Skip to main content

Authentication service
RFC 912

Document Type RFC - Unknown (September 1984)
Obsoleted by RFC 931
Authors
Last updated 2013-03-02
RFC stream Legacy
Formats
IESG Responsible AD (None)
Send notices to (None)
RFC 912
Network Working Group                                       Mike StJohns
Request for Comments: 912                                           TPSC
                                                          September 1984

                         Authentication Service

STATUS OF THIS MEMO

   This RFC suggests a proposed protocol for the ARPA-Internet
   community, and  requests discussion and suggestions for improvements.
   Distribution of this memo is unlimited.

INTRODUCTION

   The Authentication Server provides a means to determine the identity
   of a user of a particular TCP connection.  Given a TCP port number
   pair, it returns a character string which identifies the owner of
   that connection on the server's system.  Suggested uses include
   automatic identification and verification of a user during an FTP
   session, additional verification of a TAC dial up user, and access
   verification for a generalized network file server.

OVERVIEW

   This is a connection based application on TCP.  A server listens for
   TCP connections on TCP port 113 (decimal).  Once a connection is
   established, the server reads one line of data which specifies the
   connection of interest.  If it exists, the system dependent user
   identifier of the connection of interest is sent out the connection.
   The service closes the connection after sending the user identifier.

RESTRICTIONS

   Queries are permitted only for fully specified connections.  The
   local/foreign host pair used to fully specify the connection are
   taken from the query connection.  This means a user on Host A may
   only query the server on Host B about connections between A and B.

QUERY/RESPONSE FORMAT

   The server accepts simple text query requests of the form

      <local-port>, <foreign-port>

   where <local-port>, is the TCP port (decimal) on the target (server)
   system, and <foreign-port> is the TCP port (decimal) on the source
   (user) system.

      For example:

StJohns                                                         [Page 1]



RFC 912                                                   September 1984
Authentication Service

         23, 6191

   The response is of the form

      <local-port>, <foreign-port> : <response-type> : <additional-info>

   where <local-port>, <foreign-port> are the same pair as the query,
   <response-type> is a keyword identifying the type of response, and
   <additional info> is context dependent.

      For example:

         23, 6191 : USERID : StJohns

RESPONSE TYPES

   A response can be one of two types:

   USERID

      In this case, <additional-info> is the printable representation of
      the user identifier of the owner of the connection.  The format of
      the returned user identifier is completely system dependent.

   ERROR

      For some reason the owner of the TCP port could not be determined,
      <additional-info> tells why.  The following are suggested values
      of <additional-info> and their meanings.

         INVALID PORT

            Either the local or foreign port was improperly specified.

         NO USER

            The connection specified by the port pair is not currently
            in use.

         UNKNOWN ERROR

            Can't determine connection owner; reason unknown.
            Other values may be specified as necessary.

StJohns                                                         [Page 2]



RFC 912                                                   September 1984
Authentication Service

CAVEATS

   Unfortunately, the trustworthiness of the various host systems that
   might implement an authentication server will vary quite a bit.  It
   is up to the various applications that will use the server to
   determine the amount of trust they will place in the returned
   information.  It may be appropriate in some cases restrict the use of
   the server to within a locally controlled subnet.

APPLICATIONS

   1) Automatic user authentication for FTP.

   2) Verification for privileged network operations.  For example,
   having the server start or stop special purpose servers.

DISCLAIMER

   I designed this protocol to allow me to eliminate the bother of
   having to identify myself before continuing an FTP session.

   Since I started work on it, other applications appeared.  I have
   tried to consider all of our applications while still making this as
   general as possible.

StJohns                                                         [Page 3]