Network Working Group M. Chen
Internet-Draft W. Cao
Intended status: Standards Track Huawei Technologies Co., Ltd
Expires: September 12, 2012 A. Takacs
Ericsson
P. Pan
Infinera
March 11, 2012
LDP extensions for Pseudowire Binding to LSP Tunnels
draft-cao-pwe3-mpls-tp-pw-over-bidir-lsp-05.txt
Abstract
Many transport services require that user traffic, in the forms of
Pseudowires (PW), to be delivered on a single co-routed bidirectional
LSP or two LSPs that share the same routes. In addition, the user
traffic may traverse through multiple transport networks.
This document specifies an optional extension in LDP that enable the
binding between PWs and the underlying LSPs.
Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
Status of this Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on September 12, 2012.
Copyright Notice
Chen, et al. Expires September 12, 2012 [Page 1]
Internet-Draft Binding PW to Bi-directional LSP Tunnels March 2012
Copyright (c) 2012 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. LDP Extensions . . . . . . . . . . . . . . . . . . . . . . . . 4
2.1. PSN Tunnel Binding TLV . . . . . . . . . . . . . . . . . . 5
2.1.1. PSN Tunnel Sub-TLV . . . . . . . . . . . . . . . . . . 6
3. Theory of Operation . . . . . . . . . . . . . . . . . . . . . 8
4. PSN Binding Operation for SS-PW . . . . . . . . . . . . . . . 9
5. PSN Binding Operation for MS-PW . . . . . . . . . . . . . . . 11
6. Security Considerations . . . . . . . . . . . . . . . . . . . 12
7. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 13
7.1. LDP TLV Types . . . . . . . . . . . . . . . . . . . . . . 13
7.1.1. PSN Tunnel Sub-TLVs . . . . . . . . . . . . . . . . . 13
7.2. LDP Status Codes . . . . . . . . . . . . . . . . . . . . . 13
8. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 13
9. References . . . . . . . . . . . . . . . . . . . . . . . . . . 13
9.1. Normative References . . . . . . . . . . . . . . . . . . . 13
9.2. Informative References . . . . . . . . . . . . . . . . . . 14
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 14
Chen, et al. Expires September 12, 2012 [Page 2]
Internet-Draft Binding PW to Bi-directional LSP Tunnels March 2012
1. Introduction
Pseudo Wire (PW) Emulation Edge-to-Edge (PWE3) [RFC3985] is a
mechanism to emulate a number of layer 2 services, such as
Asynchronous Transfer Mode (ATM), Frame Relay or Ethernet. Such
services are emulated between two Attachment Circuits (ACs) and the
PW encapsulated layer 2 service payload is carried through Packet
Switching Network (PSN) tunnels between Provider Edges (PEs). PWE3
typically uses Label Distribution Protocol (LDP) [RFC5036] or
Resource ReserVation Protocol-Traffic Engineering (RSVP-TE) [RFC3209]
LSPs as PSN tunnels. The PEs select and bind the Pseudowires to PSN
tunnels independently. Today, there is no protocol-based
provisioning mechanism to associate a PW with a specific PSN tunnel.
The requirement for explicit control of PW-to-LSP mapping has been
specified in Section 5.3.2 ( "Support for Explicit Control of PW-to-
LSP Binding" ) of [RFC6373]. The following figure (Figure 1)
illustrates a scenario that requires the explicit PW-to-LSP binding.
+------+ +------+
---AC1 ---|..............PWs...............|---AC1---
---...----| PE1 |=======LSPs=======| PE2 |---...---
---ACn ---| |-------Links------| |---ACn---
+------+ +------+
Figure 1: Explicit PW-to-LSP binding scenario
There are two PEs (PE1 and PE2) connected through multiple parallel
links that may be on different fibers. Each link is managed and
controlled as a bi-directional LSP. At each PE, there are a large
number of bi-directional user flows from multiple Ethernet
interfaces. Each user flow uses a PW to carry traffic on forwarding
and reverse direction. The operators need to make sure that the user
flows (that is, the PW-pairs) to be carried on the same fiber (or,
bidirectional LSP).
There are a number of reasons behind this requirement. First, due to
delay and latency, traffic going over different fibers may require
large amount of expensive buffer memory to compensate for the
differential delay at the headend nodes. Further, the operators may
apply different protection mechanisms on different parts of the
network. As such, for optimal traffic management, traffic belongs to
the same user should traverse over the same fiber. In
transportation, both forwarding and reserve direction PW's that
belong to the same user flow need to be mapped to the same co-routed
bi-directional LSP or two LSPs with the same route.
Chen, et al. Expires September 12, 2012 [Page 3]
Internet-Draft Binding PW to Bi-directional LSP Tunnels March 2012
Figure 2 illustrates the case where explicit PW-LSP binding not
applied.
+----+ +--+ LSP1 +--+ +----+
+-----+ | PE1|===|P1|======|P2|===| PE2| +-----+
| |----| | +--+ +--+ | |----| |
| CE1 | |............PW................| | CE2 |
| |----| | +--+ | |----| |
+-----+ | |======|P3|==========| | +-----+
+----+ +--+ LSP2 +----+
Figure 2: Inconsistent SS-PW to LSP binding scenario
There are two bidirectional LSPs, LSP1 and LSP2, on diverse paths.
The operator is to deliver a bi-directional flow between PE1 and PE2.
Using the existing mechanisms, it's possible that PE1 may select LSP1
(PE1-P1-P2-PE2) as the PSN tunnel for the PW from PE1 to PE2, while
selecting LSP2 (PE1-P3-PE2) as the PSN tunnel for the PW from PE2 to
PE1.
Consequently, the bidirectional transport service is delivered over
two disjoint LSPs, that may have completely different service
attributes in terms of latency and protection. This may not be
acceptable as a reliable and effective transport service to the
customers.
The similar problems may also exist in multi-segment PWs (MS-PWs),
where user traffic on a particular PW may hop over different networks
on forward and reverse directions.
One way to solve this problem is by introducing manual configuration
at each PE to bind the PWs and the underlying PSN tunnels. However,
this is prone to configuration errors and does not scale.
In this documentation, we will introduce an automatic solution by
extending FEC 128/129 PW based on [RFC4447].
2. LDP Extensions
This document defines a new TLV, PSN Tunnel Binding TLV, to
communicate tunnel/LSPs selection and binding requests between PEs at
the PW setup time. The TLV carries PW's binding profile and provides
explicit and/or inexplicit information on the underlying PSN tunnels.
The binding TLV is optional, and MUST NOT affect the existing PW
Chen, et al. Expires September 12, 2012 [Page 4]
Internet-Draft Binding PW to Bi-directional LSP Tunnels March 2012
operation when not present in the messages.
The binding operation applies in both single-segment (SS) and multi-
segment (MS) scenarios.
The extension supports two types of binding requests:
1. Congruent binding: a requesting PE will suggest a underlying LSP
to a remote PE. On receive, the remote PE has the option to
either using the suggested LSP, or choose another LSP that can
deliver both forwarding and reverse direction traffic over the
same route.
2. Strict binding: the requesting PE will choose and explicitly
indicate the LSP information in the requests.
In this document, the terminology of "tunnel" is identical to the "TE
Tunnel" defined in Section 2.1 of [RFC3209], which is uniquely
identified by a SESSION object that includes Tunnel end point
address, Tunnel ID and Extended Tunnel ID. The terminology "LSP" is
identical to the "LSP tunnel" defined in Section 2.1 of [RFC3209],
which is uniquely identified by the SESSION object together with
SENDER_TEMPLATE (or FILTER_SPEC) object that consists of LSP ID and
Tunnel end point address.
2.1. PSN Tunnel Binding TLV
PSN Tunnel Binding TLV is an optional TLV and MUST be carried in the
LDP Label Mapping message if PW to LSP binding is required. The
format is as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|1|1| PSN Tunnel Binding (TBA) | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Flag | Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
~ PSN Tunnel Sub-TLV ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 3: PSN Tunnel Binding TLV
The PSN Tunnel Binding TLV type is to be allocated by IANA.
The Length field is 2 octets in length. It defines the length in
Chen, et al. Expires September 12, 2012 [Page 5]
Internet-Draft Binding PW to Bi-directional LSP Tunnels March 2012
octets of the entire TLV.
The Flag field describes the binding requests, and has following
format:
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| MUST be Zero |C|S|T|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Three flags have been defined at the present time.
C (Congruent path) bit: This informs the remote T-PE/S-PEs about the
properties of the underlying LSPs. When set, the remote T-PE/S-PEs
need to select LSPs with the same route (e.g., the same co-routed
bidirectional LSP as the requesting PE selected). If there is no
satisfied tunnel, it may trigger the remote T-PE/S-PEs to establish a
new LSP.
S (Strict) bit: This instructs the PEs with respect to the handling
of the underlying LSPs. When set, the remote PE MUST use the tunnel/
LSPs specified in the PSN Tunnel Sub-TLV as the PSN tunnel on the
reverse direction of the PW, or the PW will fail to be established.
T (Tunnel Representation) bit: This indicates the format of the LSP
tunnels. When the bit is set, the tunnel uses the tunnel information
to identify itself, and the LSP Number fields in the PSN Tunnel sub-
TLV (Section 2.1.1) MUST be set to zero. Otherwise, both tunnel and
LSP information of the PSN tunnel are required. The default is set.
C-bit and S-bit are mutually exclusive from each other, and cannot be
set in the same message.
2.1.1. PSN Tunnel Sub-TLV
PSN Tunnel Sub-TLVs are designed for inclusion in the PSN Tunnel
Binding TLV to specify the tunnel/LSPs to which a PW is required to
bind.
In this document two sub-TLVs are defined: the IPv4/IPv6 Tunnel sub-
TLVs. The format of the PSN Tunnel sub-TLVs is as follows:
Chen, et al. Expires September 12, 2012 [Page 6]
Internet-Draft Binding PW to Bi-directional LSP Tunnels March 2012
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0|0| IPv4 PSN Tunnel sub-TLV | TLV Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source Global ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source Node ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source Tunnel Number | Source LSP Number (optional) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Destination Global ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Destination Node ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Destination Tunnel Number | Destination LSP Number (opt.) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 4: IPv4 PSN Tunnel sub-TLV format
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0|0| IPv6 PSN Tunnel sub-TLV | TLV Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source Global ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
~ Source Node ID ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source Tunnel Number | Source LSP Number (optional) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Destination Global ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
~ Destination Node ID ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Destination Tunnel Number | Destination LSP Number (opt.) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 5: IPv6 PSN Tunnel sub-TLV format
The definition of Source and Destination Global/Node IDs and Tunnel/
LSP Numbers are derived from [RFC6370]. The notation is designed to
describe co-routed or associated bi-directional LSPs.
As defined in Section 4.6.1.2 and Section 4.6.2.2 of [RFC3209], the
"Tunnel end point address" is mapped to Destination Node ID, and
Chen, et al. Expires September 12, 2012 [Page 7]
Internet-Draft Binding PW to Bi-directional LSP Tunnels March 2012
"Extended Tunnel ID" is mapped to Source Node ID. Both IDs can be
IPv6 addresses.
A PSN Tunnel sub-TLV could be used to either identify a tunnel or a
specific LSP. The T-bit in the Flag field determines whether it
stands for tunnel or LSP.
When the T-bit is set, it identifies a tunnel, and the Source/
Destination LSP Number fields MUST be set to zero and ignored during
processing. Otherwise, both Source/Destination LSP Number fields
MUST have the actual LSP IDs of specific LSPs.
Each PSN Tunnel Binding TLV can only have one such sub-TLV.
3. Theory of Operation
During PW setup, the PEs may select desired forwarding tunnels/LSPs,
and inform the remote T-PE/S-PEs about the desired reverse tunnels/
LSPs.
Specifically, to set up a PW (or PW Segment), a PE may select a
candidate LSP to act as the PSN tunnel. If none is available or
satisfies the constraints, the PE may trigger to establish a new
tunnel/LSP. The selected tunnel/LSP information is carried in the
PSN Tunnel Binding TLV and sent with the Label Mapping message to the
target PE.
Upon the reception of the Label Mapping message, the receiving PE
will process the PSN Tunnel Binding TLV, determine whether it can
accept the suggested tunnel/LSP or find the reverse tunnel/LSP that
meets the request, and respond with a Label Mapping message, which
contains the corresponding PSN Tunnel Binding TLV.
It is possible that two PEs may request PSN binding to the same PW or
PW segment over different tunnels/LSPs at the same time. There may
cause collisions of tunnel/LSPs selection as both PEs assume the
active role.
The PEs can be generally categorized into two types:
1. Active PE: the PE which initiates the selection of the tunnel/
LSPs and informs the remote PE;
2. Passive PE: the PE which obeys the active PE's suggestion.
Segmented PW has defined the active/passive role election (Section
7.2.1, [RFC6073]). This document will not define any new procedures.
Chen, et al. Expires September 12, 2012 [Page 8]
Internet-Draft Binding PW to Bi-directional LSP Tunnels March 2012
In the remaining of this document, it will elaborate the operation in
two situations:
1. SS-PW: In this scenario, both PEs of a PW assume active roles
2. MS-PW: One PE is active, while the other is passive. The PWs are
setup using FEC 129
4. PSN Binding Operation for SS-PW
As illustrated in Figure-5, both PEs (say, PE1 and PE2) of a PW may
independently initiate the setup. To perform PSN binding, the Label
Mapping messages MUST carry a PSN Tunnel Binding TLV, and the PSN
Tunnel sub-TLV MUST contains the desired tunnel/LSPs of the sender.
+----+ LSP1 +----+
+-----+ | PE1|====================| PE2| +-----+
| |----| | | |----| |
| CE1 | |............PW................| | CE2 |
| |----| | | |----| |
+-----+ | |====================| | +-----+
+----+ LSP2 +----+
Figure 6: PSN binding operation in SS-PW environment
As outlined previously, there are two types of binding request:
congruent and strict.
In strict binding, a PE (e.g., PE1) will mandate the other PE (e.g.,
PE2) to use a specified tunnel/LSP (e.g. LSP1) as the PSN tunnel on
the reverse direction. In the PSN Tunnel Binding TLV, the S-bit MUST
be set, the C-bit MUST be reset, and the Source and Destination IDs/
Numbers MUST be filled.
On receive, if the S-bit is set, other than following the processing
procedure defined in Section 5.3.3 of [RFC4447], the receiving PE
(i.e. PE2) needs to determine whether to accept the indicated
tunnel/LSP in PSN Tunnel Sub-TLV.
If the receiving PE (PE2) is also an active PE, and may have
initiated the PSN binding requests to the other PE (PE1), it MUST
compare its own Node ID against the received Source Node ID. If it
is numerically lower, the PE (PE2) will reply a Label Mapping message
to complete the PW setup and confirm the binding request. The PSN
Tunnel Binding TLV in the message MUST contain the same Source and
Destination IDs/Numbers as in the received binding request, in the
Chen, et al. Expires September 12, 2012 [Page 9]
Internet-Draft Binding PW to Bi-directional LSP Tunnels March 2012
appropriate order.
On the other hand, if the receiving PE (PE2) has a Node ID that is
numerically higher than the Source Node ID carried in the PSN Tunnel
Binding TLV, it MUST reply a Label Release message with status code
set to "Reject to use the suggested tunnel/LSPs" and the received PSN
Tunnel Binding TLV.
To support congruent binding, the receiving PE can select the
appropriated PSN tunnel/LSP for the reverse direction of the PW, so
long as the forwarding and reverse PSNs have the same route.
Initially, a PE (PE1) sends a Label Mapping message to the remote PE
(PE2) with the PSN Tunnel Binding TLV, with C-bit set, S-bit reset,
and the appropriate Source and Destination IDs/Numbers. In case of
unidirectional LSPs, the PSN Tunnel Binding TLV may only contain the
Source IDs/Numbers, the Destination IDs/Numbers are set to zero and
left for PE2 to fill when responding the Label Mapping message.
On receive, since PE2 is also an active PE, it needs to compare its
own Node ID against the received Source Node ID. If it's numerically
lower, PE2 needs to find/establish a tunnel/LSP that meets the
congruent constraint, and then reply a Label Mapping message with a
PSN Binding TLV that contains the Source and Destination IDs/Numbers
in the appropriate order.
On the other hand, if the receiving PE (PE2) has a Node ID that is
numerically higher than the Source Node ID carried in the PSN Tunnel
Binding TLV, it MUST reply a Label Release message with status code
set to "Reject to use the suggested tunnel/LSPs" and the received PSN
Tunnel Binding TLV.
In both strict and congruent bindings, if T-bit is set, the LSP
Number field MUST be set to zero. Otherwise, the field MUST contain
the actual LSP number for the associated PSN LSP.
After a PW established, the operators may choose to switch the PW
from the current tunnel/LSPs. Or, the underlying PSN is broken due
to network failure. In this scenario, a new Label Mapping message
MUST be sent to update the changes. Noting that when T-bit is set,
the working LSP broken will not trigger to update the changes if
there are protection LSPs.
The message may carry a new PSN Tunnel Binding TLV, which contains
the new Source and Destination Numbers/IDs. The handling of the new
message should be identical to what has been described in this
section.
Chen, et al. Expires September 12, 2012 [Page 10]
Internet-Draft Binding PW to Bi-directional LSP Tunnels March 2012
However, if the new Label Binding message does not contain the PSN
Tunnel Binding TLV, it declares the removal of any congruent/strict
constraints. The PEs may not map the PW to the underlying PSN on
purpose, the current independent PW to PSN binding will be used.
Further, as an implementation option, the PEs should not remove the
traffic from an operational PW, until the completion of the
underlying PSN tunnel/LSP changes.
5. PSN Binding Operation for MS-PW
MS-PW uses FEC 129 for PW setup. We refer the operation to Figure-6.
+-----+ LSP1 +-----+ LSP2 +-----+ LSP3 +-----+
+---+ |T-PE1|======|S-PE1|======|S-PE2|======|T-PE2| +---+
| |---| | | | | | | |---| |
|CE1| |......................PW....................| |CE2|
| |---| | | | | | | |---| |
+---+ | |======| |======| |======| | +---+
+-----+ LSP4 +-----+ LSP5 +-----+ LSP6 +-----+
Figure 7: PSN binding operation in MS-PW environment
When the active PE (T-PE1) starts to signal for a MS-PW, a PSN Tunnel
Binding TLV MUST be carried in the Label Mapping message and sent to
the adjacent S-PE (say S-PE1). The PSN Tunnel Binding TLV includes
the PSN Tunnel sub-TLV that carries the desired tunnel/LSP of
T-PE1's.
For strict binding, the initiating PE (T-PE1) MUST set the S-bit,
reset the C-bit and indicates the binding tunnel/LSP to the next-hop
S-PE (S-PE1).
When S-PE1 receives the Label Mapping message, S-PE1 needs to
determine if the signaling is for forward or reverse direction, as
defined in Section 6.2.3 of [I-D.ietf-pwe3-dynamic-ms-pw].
If the Label Mapping message is for forward direction, and S-PE1
accepts the requested tunnel/LSPs from T-PE1, S-PE1 must save the
tunnel/LSP information for reverse-direction processing later on. If
the PSN binding request is not acceptable, S-PE1 MUST reply a Label
Release Message to the upstream PE (T-PE1) with Status Code set to
"Reject to use the suggested tunnel/LSPs".
Chen, et al. Expires September 12, 2012 [Page 11]
Internet-Draft Binding PW to Bi-directional LSP Tunnels March 2012
Otherwise, S-PE1 relays the Label Mapping message to the next S-PE
(S-PE2), with the PSN Tunnel sub-TLV carrying the information of the
new PSN tunnel/LSPs selected by S-PE1 for the next PW segment. S-PE2
and subsequent S-PEs will repeat the same operation until the Label
Mapping message reaches to the remote T-PE (T-PE2).
If T-PE2 agrees with the requested tunnel/LSPs, it will reply a Label
Mapping message to initiate to the binding process on the reverse
direction. The Label Mapping message contains the received PSN
Tunnel Binding TLV for confirmation purposes.
When its upstream S-PE (S-PE2) receives the Label Mapping message,
the S-PE relays the Label Mapping message to its upstream adjacent
S-PE (S-PE1), with the previously saved PSN tunnel/LSP information in
the PSN Tunnel sub-TLV. The same procedure will be applied on
subsequent S-PEs, until the message reaches to T-PE1 to complete the
PSN binding setup.
During the binding process, if any PE does not agree to the requested
tunnel/LSPs, it can send a Label Release Message to its upstream
adjacent PE with Status Code set to "Reject to use the suggested
tunnel/LSPs".
For congruent binding, the initiating PE (T-PE1) MUST set the C-bit,
reset the S-bit and indicates the suggested tunnel/LSP in PSN Tunnel
sub-TLV to the next-hop S-PE (S-PE1).
During the MS-PW setup, the PEs have the option to ignore the
suggested tunnel/LSP, and select another tunnel/LSP for the segment
PW between itself and its upstream PE on reverse direction only if
the tunnel/LSP is congruent with the forwarding one. Otherwise, the
procedure is the same as the strict binding.
The tunnel/LSPs may change after a MS-PW being established. When a
tunnel/LSP has changed, the PE that detects the change SHOULD select
an alternative tunnel/LSP for temporary use while negotiating with
other PEs following the procedure described in this section.
6. Security Considerations
The ability to control which LSP to carry traffic from a PW can be a
potential security risk both for denial of service and traffic
interception. It is RECOMMENDED that PEs do not accept the use of
LSPs identified in the PSN Tunnel Binding TLV unless the LSP end
points match the PW or PW segment end points. Furthermore, where
security of the network is believed to be at risk, it is RECOMMENDED
that PEs implement the LDP security mechanisms described in [RFC5036]
Chen, et al. Expires September 12, 2012 [Page 12]
Internet-Draft Binding PW to Bi-directional LSP Tunnels March 2012
and [RFC5920].
7. IANA Considerations
7.1. LDP TLV Types
This document defines new TLV [Section 2.1 of this document] for
inclusion in LDP Label Mapping message. IANA is required to assign
TLV type value to the new defined TLVs from LDP "TLV Type Name Space"
registry.
7.1.1. PSN Tunnel Sub-TLVs
This document defines two sub-TLVs [Section 2.1.1 of this document]
for PSN Tunnel Binding TLV. IANA is required to create a new
registry ("PSN Tunnel Sub-TLV Name Space") for PSN Tunnel sub-TLVs
and to assign Sub-TLV type values to the following sub-TLVs.
IPv4 PSN Tunnel sub-TLV - 0x01 (to be confirmed by IANA)
IPv6 PSN Tunnel sub-TLV - 0x02 (to be confirmed by IANA)
7.2. LDP Status Codes
This document defines a new LDP status codes, IANA is required to
assigned status codes to these new defined codes from LDP "STATUS
CODE NAME SPACE" registry.
"Reject to use the suggested tunnel/LSPs" - 0x0000003B (to be
confirmed by IANA)
8. Acknowledgements
The authors would like to thank Adrian Farrel, Mingming Zhu and Li
Xue for their comments and help in preparing this document. Also
this draft benefits from the discussions with Nabil Bitar, Paul
Doolan, Frederic Journay, Andy Malis, Curtis Villamizar and Luca
Martini.
9. References
9.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
Chen, et al. Expires September 12, 2012 [Page 13]
Internet-Draft Binding PW to Bi-directional LSP Tunnels March 2012
[RFC4447] Martini, L., Rosen, E., El-Aawar, N., Smith, T., and G.
Heron, "Pseudowire Setup and Maintenance Using the Label
Distribution Protocol (LDP)", RFC 4447, April 2006.
[RFC6370] Bocci, M., Swallow, G., and E. Gray, "MPLS Transport
Profile (MPLS-TP) Identifiers", RFC 6370, September 2011.
9.2. Informative References
[I-D.ietf-pwe3-dynamic-ms-pw]
Martini, L., Bocci, M., and F. Balus, "Dynamic Placement
of Multi Segment Pseudowires",
draft-ietf-pwe3-dynamic-ms-pw-14 (work in progress),
July 2011.
[RFC3209] Awduche, D., Berger, L., Gan, D., Li, T., Srinivasan, V.,
and G. Swallow, "RSVP-TE: Extensions to RSVP for LSP
Tunnels", RFC 3209, December 2001.
[RFC3471] Berger, L., "Generalized Multi-Protocol Label Switching
(GMPLS) Signaling Functional Description", RFC 3471,
January 2003.
[RFC3473] Berger, L., "Generalized Multi-Protocol Label Switching
(GMPLS) Signaling Resource ReserVation Protocol-Traffic
Engineering (RSVP-TE) Extensions", RFC 3473, January 2003.
[RFC3985] Bryant, S. and P. Pate, "Pseudo Wire Emulation Edge-to-
Edge (PWE3) Architecture", RFC 3985, March 2005.
[RFC5036] Andersson, L., Minei, I., and B. Thomas, "LDP
Specification", RFC 5036, October 2007.
[RFC5920] Fang, L., "Security Framework for MPLS and GMPLS
Networks", RFC 5920, July 2010.
[RFC6073] Martini, L., Metz, C., Nadeau, T., Bocci, M., and M.
Aissaoui, "Segmented Pseudowire", RFC 6073, January 2011.
[RFC6373] Andersson, L., Berger, L., Fang, L., Bitar, N., and E.
Gray, "MPLS Transport Profile (MPLS-TP) Control Plane
Framework", RFC 6373, September 2011.
Chen, et al. Expires September 12, 2012 [Page 14]
Internet-Draft Binding PW to Bi-directional LSP Tunnels March 2012
Authors' Addresses
Mach(Guoyi) Chen
Huawei Technologies Co., Ltd
Q14 Huawei Campus, No. 156 Beiqing Road, Hai-dian District
Beijing 100095
China
Email: mach@huawei.com
Wei Cao
Huawei Technologies Co., Ltd
Q14 Huawei Campus, No. 156 Beiqing Road, Hai-dian District
Beijing 100095
China
Email: wayne.caowei@huawei.com
Attila Takacs
Ericsson
Laborc u. 1.
Budapest 1037
Hungary
Email: attila.takacs@ericsson.com
Ping Pan
Infinera
169 West Java Drive, Sunnyvale, CA 94089
US
Email: ppan@infinera.com
Chen, et al. Expires September 12, 2012 [Page 15]