Network Working Group B. Ray
Category: Internet Draft PESA Switching Systems
R. Abbi
Alcatel
June 2003
Definitions of Managed Objects for Very High
Speed Digital Subscriber Lines (VDSL)
draft-ietf-adslmib-vdsl-10.txt
Status of this Memo
This document is an Internet-Draft and is in full conformance with
all provisions of Section 10 of RFC2026.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as
Internet-Drafts.
Internet-Drafts are draft documents valid for a maximum of six
months and may be updated, replaced, or obsoleted by other documents
at any time. It is inappropriate to use Internet-Drafts as
reference material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at:
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at:
http://www.ietf.org/shadow.html.
Copyright Notice
Copyright (C) The Internet Society (2003). All Rights Reserved.
Abstract
This document defines a portion of the Management Information Base
(MIB) module for use with network management protocols in the
Internet community. In particular, it describes objects used for
managing Very High Speed Digital Subscriber Line (VDSL) interfaces.
Expires December 12, 2003 [Page 1]
INTERNET-DRAFT VDSL-LINE MIB June 2003
Table of Contents
1. The Internet-Standard Management Framework .................... 2
2. Overview ...................................................... 2
2.1 Relationship of the VDSL Line MIB Module to other MIB Modules . 2
2.2 Conventions used in the MIB Module ............................ 4
2.3 Structure ..................................................... 5
2.4 Counters, Interval Buckets and Thresholds ..................... 6
2.5 Profiles ...................................................... 7
2.6 Notifications ................................................. 8
2.7 Persistence ................................................... 9
3. Conformance and Compliance .................................... 10
4. Definitions ................................................... 10
5. Intellectual Property ......................................... 64
6. Normative References .......................................... 65
7. Informative References ........................................ 66
8. Security Considerations ....................................... 66
9. Acknowledgements .............................................. 67
10. Authors' Addresses ............................................ 68
11. Full Copyright Statement ...................................... 68
1. The Internet-Standard Management Framework
For a detailed overview of the documents that describe the current
Internet-Standard Management Framework, please refer to section 7 of
RFC 3410 [RFC3410].
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. MIB objects are generally
accessed through the Simple Network Management Protocol (SNMP).
Objects in the MIB are defined using the mechanisms defined in the
Structure of Management Information (SMI). This memo specifies a
MIB module that is compliant to the SMIv2, which is described in STD
58, RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC
2580 [RFC2580].
2. Overview
This document describes an SNMP MIB module for managing VDSL Lines.
These definitions are based upon the specifications for VDSL as
defined in T1E1, ETSI, and ITU documentation [T1E1311, T1E1011,
T1E1013, ETSI2701, ETSI2702, ITU9931, ITU9971].
The MIB module is located in the MIB tree under MIB 2 transmission,
as discussed in the MIB-2 Integration (RFC 2863 [RFC2863]) section
of this document.
2.1 Relationship of the VDSL Line MIB Module to other MIB Modules
This section outlines the relationship of this MIB with other MIBs
Expires December 12, 2003 [Page 2]
INTERNET-DRAFT VDSL-LINE MIB June 2003
described in RFCs. Specifically, IF-MIB as presented in RFC 2863
[RFC2863] is discussed.
2.1.1 General IF-MIB Integration (RFC 2863)
The VDSL Line MIB specifies the detailed attributes of a data
interface. As such, it needs to integrate with RFC 2863 [RFC2863].
The IANA has assigned the following ifType to VDSL:
IANAifType ::= TEXTUAL-CONVENTION
...
SYNTAX INTEGER {
...
vdsl(97), -- Very H-speed Digital Subscrib. Loop
...
}
Additionally, a VDSL line may contain an optional fast channel
and an optional interleaved channel which also integrate into RFC
2863 [RFC2863]. The IANA has assigned the following ifTypes to
these channels:
IANAifType ::= TEXTUAL-CONVENTION
...
SYNTAX INTEGER {
...
interleave (124), -- Interleave channel
fast (125), -- Fast channel
...
}
2.1.2 Usage of ifTable
The MIB branch identified by this ifType contains tables appropriate
for this interface type. Most such tables extend the ifEntry table,
and are indexed by ifIndex. For interfaces in systems implementing
this MIB, those table entries indexed by ifIndex MUST be persistent.
The following attributes are part of the mandatory ifGeneral group
in RFC 2863 [RFC2863], and are not duplicated in the VDSL Line MIB.
===================================================================
ifIndex Interface index.
ifDescr See interfaces MIB [RFC2863].
ifType vdsl(97),
interleaved(124), or
fast(125)
ifSpeed Set as appropriate.
Expires December 12, 2003 [Page 3]
INTERNET-DRAFT VDSL-LINE MIB June 2003
ifPhysAddress This object MUST have an octet string
with zero length.
ifAdminStatus See interfaces MIB [RFC2863].
ifOperStatus See interfaces MIB [RFC2863].
ifLastChange See interfaces MIB [RFC2863].
ifName See interfaces MIB [RFC2863].
ifHighSpeed Set as appropriate.
ifConnectorPresent Set as appropriate.
ifLinkUpDownTrapEnable Default to enabled(1).
===================================================================
Figure 1: Use of ifTable Objects
Section 2.3, below, describes the structure of this MIB in relation
to ifEntry in greater detail.
2.2 Conventions used in the MIB Module
2.2.1 Naming Conventions
A. Vtuc -- (VTUC) transceiver at near (Central) end of line
B. Vtur -- (VTUR) transceiver at Remote end of line
C. Vtu -- One of either Vtuc or Vtur
D. Curr -- Current
E. Prev -- Previous
F. Atn -- Attenuation
G. ES -- Errored Second
H. SES -- Severely Errored Second
I. UAS -- Unavailable Second
J. LCS -- Line Code Specific
K. Lof -- Loss of Frame
L. Lol -- Loss of Link
M. Los -- Loss of Signal
N. Lpr -- Loss of Power
O. xxxs -- Sum of Seconds in which xxx has occurs (e.g., xxx=Lof,
Los, Lpr, Lol)
P. Max -- Maximum
Q. Mgn -- Margin
R. Min -- Minimum
S. Psd -- Power Spectral Density
T. Snr -- Signal to Noise Ratio
U. Tx -- Transmit
V. Blks -- Blocks
Expires December 12, 2003 [Page 4]
INTERNET-DRAFT VDSL-LINE MIB June 2003
2.2.2 Textual Conventions
The following textual conventions are defined to reflect the line
topology in the MIB (further discussed in the following section)
and to define the behavior of the statistics to be maintained
by an agent.
o VdslLineCodingType :
Attributes with this syntax identify the line coding used.
Specified as an INTEGER, the three values are:
other(1) -- none of the following
mcm(2) -- Multiple Carrier Modulation
scm(3) -- Single Carrier Modulation
o VdslLineEntity :
Attributes with this syntax reference the two sides of a line.
Specified as an INTEGER, the two values are:
vtuc(1) -- central site transceiver
vtur(2) -- remote site transceiver
2.3 Structure
The MIB is structured into the following MIB groups:
o vdslGroup :
This group supports all line code independent MIB objects found
in this MIB. The following tables contain objects permitted for
ifType vdsl(97):
- vdslLineTable
- vdslPhysTable
- vdslPerfDataTable
- vdslPerfIntervalTable
- vdslPerf1DayIntervalTable
- vdslLineConfProfileTable
- vdslLineAlarmConfProfileTable
The following tables contain objects permitted for ifTypes
interleaved(124) and (fast):
- vdslChanTable
- vdslChanPerfDataTable
- vdslChanPerfIntervalTable
- vdslChanPerf1DayIntervalTable
Figure 2, below, displays the relationship of the tables in the
vdslGroup to ifEntry (and each other):
Expires December 12, 2003 [Page 5]
INTERNET-DRAFT VDSL-LINE MIB June 2003
ifEntry(ifType=97) ----> vdslLineTableEntry 1:(0 to 1)
vdslLineTableEntry ----> vdslPhysTableEntry 1:(0 to 2)
----> vdslPerfDataEntry 1:(0 to 2)
----> vdslLineConfProfileEntry 1:(0 to 1)
----> vdslLineAlarmConfProfileEntry 1:(0 to 1)
vdslPhysTableEntry ----> vdslPerfIntervalEntry 1:(0 to 96)
----> vdslPerf1DayIntervalEntry 1:(0 to 30)
ifEntry(ifType=124) ----> vdslChanEntry 1:(0 to 2)
----> vdslChanPerfDataEntry 1:(0 to 2)
ifEntry(ifType=125) ----> vdslChanEntry 1:(0 to 2)
----> vdslChanPerfDataEntry 1:(0 to 2)
vdslChanEntry ----> vdslchanPerfIntervalEntry 1:(0 to 96)
----> vdslchan1DayPerfIntervalEntry 1:(0 to 30)
Figure 2: Table Relationships
o vdslNotificationGroup :
This group contains definitions of VDSL line notifications. Section
2.6, below, presents greater detail on the notifications defined
within the MIB module.
2.3.1 Line Topology
A VDSL Line consists of two units - a Vtuc (the central tranceiver
unit) and a Vtur (the remote transceiver unit).
<-- Network Side Customer Side -->
|<////////// VDSL Line ///////////>|
+-------+ +-------+
| | | |
| Vtuc +------------------+ Vtur |
| | | |
+-------+ +-------+
Figure 3: General topology for a VDSL Line
2.4 Counters, Interval Buckets and Thresholds
For Loss of Frame (lof), Loss of Link (lol), Loss of Signal (los),
and Loss of Power (lpr), Errored Seconds (ES), Severely Errored
Seconds (SES), and Unavailable Seconds (UAS) there are event
counters, current 15-minute, 0 to 96 15-minute history bucket(s),
Expires December 12, 2003 [Page 6]
INTERNET-DRAFT VDSL-LINE MIB June 2003
and 0 to 30 1-day history bucket(s) of "interval-counters". Each
current 15-minute event bucket has an associated threshold
notification.
Each of these counters uses the textual conventions defined in the
HC-PerfHist-TC-MIB [RFCXXXX]. The HC-PerfHist-TC-MIB defines 64-
--- RFC Ed: please replace XXXX with the RFC number assigned to the
--- accompanying HC-TC MIB
bit versions of the textual conventions found in RFC 2493 [RFC2493].
There is no requirement for an agent to ensure a fixed relationship
between the start of a fifteen minute interval and any wall clock;
however, some implementations may align the fifteen minute intervals
with quarter hours. Likewise, an implementation may choose to align
one day intervals with the start of a day.
Counters are not reset when a Vtu is reinitialized, only when the
agent is reset or reinitialized (or under specific request outside
the scope of this MIB module).
2.5 Profiles
As a managed node can handle a large number of Vtus, (e.g., hundreds
or perhaps thousands of lines), provisioning every parameter on
every Vtu may become burdensome. Moreover, most lines are
provisioned identically with the same set of parameters. To
simplify the provisioning process, this MIB makes use of profiles.
A profile is a set of parameters that can be shared by multiple
lines using the same configuration.
The following profiles are used in this MIB module:
o Line Configuration Profiles - Line configuration profiles
contain parameters for configuring VDSL lines. They are defined
in the vdslLineConfProfileTable.
o Alarm Configuration Profiles - These profiles contain parameters
for configuring alarm thresholds for VDSL transceivers. These
profiles are defined in the vdslLineAlarmConfProfileTable.
One or more lines may be configured to share parameters of a single
profile by setting its vdslLineConfProfile objects to the value of
this profile. If a change is made to the profile, all lines that
refer to it will be reconfigured to the changed parameters. Before
a profile can be deleted or taken out of service it must be first
unreferenced from all associated lines.
Implementations MUST provide a default profile with an index value
of 'DEFVAL' for each profile type. The values of the associated
parameters will be vendor specific unless otherwise indicated in
this document. Before a line's profiles have been set, these
profiles will be automatically used by setting vdslLineConfProfile
Expires December 12, 2003 [Page 7]
INTERNET-DRAFT VDSL-LINE MIB June 2003
and vdslLineAlarmConfProfile to 'DEFVAL' where appropriate. This
default profile name, 'DEFVAL', is considered reserved in the
context of profiles defined in this MIB module.
Profiles are created, assigned, and deleted dynamically using the
profile name and profile row status in each of the ten profile
tables (nine line configuration tables and one alarm configuration
table).
Profile changes MUST take effect immediately. These changes MAY
result in a restart (hard reset or soft restart) of the units on the
line.
2.6 Notifications
The ability to generate the SNMP notifications coldStart/WarmStart
(per [RFC3418]) which are per agent (e.g., per Digital Subscriber
Line Access Multiplexer, or DSLAM, in such a device), and
linkUp/linkDown (per [RFC2863]) which are per interface (i.e., VDSL
line) is required.
The notifications defined in this MIB are for initialization failure
and for the threshold crossings associated with the following
events: lof, lol, los, lpr, ES, SES, and UAS. Each threshold has
its own enable/threshold value. When that value is 0, the
notification is disabled.
A linkDown notification MAY be generated whenever any of lof, lol,
los, lpr, ES, SES, or UAS threshold crossing event (as defined
in this MIB module) occurs. The corresponding linkUp notification
MAY be sent when all link failure conditions are cleared.
The vdslCurrStatus is a bitmask representing all outstanding error
conditions associated with a particular VDSL transceiver. Note that
since status of remote transceivers is obtained via the EOC, this
information may be unavailable for units that are unreachable via
EOC during a line error condition. Therefore, not all conditions
may always be included in its current status. Notifications
corresponding to the bit fields in this object are defined.
A threshold notification occurs whenever the corresponding current
15-minute interval error counter becomes equal to, or exceeds the
threshold value. One notification may be sent per interval per
interface. Since the current 15-minute counter are reset to 0 every
15 minutes, if the condition persists, the notification may recur as
often as every 15 minutes. For example, to get a notification
whenever a "loss of" event occurs (but at most once every 15
minutes), set the corresponding threshold to 1. The agent will
generate a notification when the event originally occurs.
Note that the Network Management System, or NMS, may receive a
linkDown notification, as well, if enabled (via
Expires December 12, 2003 [Page 8]
INTERNET-DRAFT VDSL-LINE MIB June 2003
ifLinkUpDownTrapEnable [RFC2863]). At the beginning of the next 15
minute interval, the counter is reset. When the first second goes
by and the event occurs, the current interval bucket will be 1,
which equals the threshold and the notification will be sent again.
2.7 Persistence
All read-write and read-create objects defined in this MIB module
SHOULD be stored persistently. Following is an exhaustive list of
these persistent objects:
vdslLineConfProfile
vdslLineAlarmConfProfile
vdslLineConfProfileName
vdslLineConfDownRateMode
vdslLineConfUpRateMode
vdslLineConfDownMaxPwr
vdslLineConfUpMaxPwr
vdslLineConfDownMaxSnrMgn
vdslLineConfDownMinSnrMgn
vdslLineConfDownTargetSnrMgn
vdslLineConfUpMaxSnrMgn
vdslLineConfUpMinSnrMgn
vdslLineConfUpTargetSnrMgn
vdslLineConfDownFastMaxDataRate
vdslLineConfDownFastMinDataRate
vdslLineConfDownSlowMaxDataRate
vdslLineConfDownSlowMinDataRate
vdslLineConfUpFastMaxDataRate
vdslLineConfUpFastMinDataRate
vdslLineConfUpSlowMaxDataRate
vdslLineConfUpSlowMinDataRate
vdslLineConfDownRateRatio
vdslLineConfUpRateRatio
vdslLineConfDownMaxInterDelay
vdslLineConfUpMaxInterDelay
vdslLineConfDownPboControl
vdslLineConfUpPboControl
vdslLineConfDownPboLevel
vdslLineConfUpPboLevel
vdslLineConfDeploymentScenario
vdslLineConfAdslPresence
vdslLineConfApplicableStandard
vdslLineConfBandPlan
vdslLineConfBandPlanFx
vdslLineConfBandOptUsage
vdslLineConfUpPsdTemplate
vdslLineConfDownPsdTemplate
vdslLineConfHamBandMask
vdslLineConfCustomNotch1Start
vdslLineConfCustomNotch1Stop
vdslLineConfCustomNotch2Start
Expires December 12, 2003 [Page 9]
INTERNET-DRAFT VDSL-LINE MIB June 2003
vdslLineConfCustomNotch2Stop
vdslLineConfDownTargetSlowBurst
vdslLineConfUpTargetSlowBurst
vdslLineConfDownMaxFastFec
vdslLineConfUpMaxFastFec
vdslLineConfLineType
vdslLineConfProfRowStatus
vdslLineAlarmConfProfileName
vdslThresh15MinLofs
vdslThresh15MinLoss
vdslThresh15MinLprs
vdslThresh15MinLols
vdslThresh15MinESs
vdslThresh15MinSESs
vdslThresh15MinUASs
vdslInitFailureNotifyEnable
vdslLineAlarmConfProfRowStatus
It SHOULD also be noted that interface indices in this MIB are
maintained persistently. VACM data relating to these SHOULD be
stored persistently as well [RFC2575].
3. Conformance and Compliance
For VDSL lines, the following groups are mandatory:
- vdslGroup
- vdslNotificationGroup
4. Definitions
VDSL-LINE-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY,
OBJECT-TYPE,
Gauge32,
Integer32,
Unsigned32,
NOTIFICATION-TYPE,
transmission FROM SNMPv2-SMI
ZeroBasedCounter64 FROM HCNUM-TC
TEXTUAL-CONVENTION,
RowStatus,
TruthValue FROM SNMPv2-TC
HCPerfValidIntervals,
HCPerfInvalidIntervals,
HCPerfTimeElapsed,
HCPerfIntervalThreshold,
HCPerfCurrentCount,
HCPerfIntervalCount FROM HC-PerfHist-TC-MIB
Expires December 12, 2003 [Page 10]
INTERNET-DRAFT VDSL-LINE MIB June 2003
MODULE-COMPLIANCE,
OBJECT-GROUP,
NOTIFICATION-GROUP FROM SNMPv2-CONF
ifIndex FROM IF-MIB
SnmpAdminString FROM SNMP-FRAMEWORK-MIB;
vdslMIB MODULE-IDENTITY
LAST-UPDATED "200306060000Z" -- June 6, 2003
ORGANIZATION "ADSLMIB Working Group"
CONTACT-INFO "WG-email: adslmib@ietf.org
Info: https://www1.ietf.org/mailman/listinfo/adslmib
Chair: Mike Sneed
Sand Channel Systems
Postal: P.O. Box 37324
Raleigh NC 27627-7324
USA
Email: sneedmike@hotmail.com
Phone: +1 206 600 7022
Co-editor: Bob Ray
PESA Switching Systems, Inc.
Postal: 330-A Wynn Drive
Huntsville, AL 35805
USA
Email: rray@pesa.com
Phone: +1 256 726 9200 ext. 142
Co-editor: Rajesh Abbi
Alcatel USA
Postal: 2912 Wake Forest Road
Raleigh, NC 27609-7860
USA
Email: Rajesh.Abbi@alcatel.com
Phone: +1 919 850 6194
"
DESCRIPTION
"The MIB module defining objects for the management of a pair
of VDSL transceivers at each end of the VDSL line. Each such
line has an entry in an ifTable which may include multiple
transceiver lines. An agent may reside at either end of the
VDSL line. However, the MIB is designed to require no
management communication between them beyond that inherent in
the low-level VDSL line protocol. The agent may monitor and
control this protocol for its needs.
VDSL lines may support optional Fast or Interleaved channels.
If these are supported, additional entries corresponding to the
supported channels must be created in the ifTable. Thus a VDSL
line that supports both channels will have three entries in the
ifTable, one for each physical, fast, and interleaved, whose
ifType values are equal to vdsl(97), fast(125), and
Expires December 12, 2003 [Page 11]
INTERNET-DRAFT VDSL-LINE MIB June 2003
interleaved(124), respectively. The ifStackTable is used to
represent the relationship between the entries.
Naming Conventions:
Vtuc -- (VTUC) transceiver at near (Central) end of line
Vtur -- (VTUR) transceiver at Remote end of line
Vtu -- One of either Vtuc or Vtur
Curr -- Current
Prev -- Previous
Atn -- Attenuation
ES -- Errored Second.
SES -- Severely Errored Second
UAS -- Unavailable Second
LCS -- Line Code Specific
Lof -- Loss of Frame
Lol -- Loss of Link
Los -- Loss of Signal
Lpr -- Loss of Power
xxxs -- Interval of Seconds in which xxx occurs
(e.g., xxx=Lof, Los, Lpr)
Max -- Maximum
Mgn -- Margin
Min -- Minimum
Psd -- Power Spectral Density
Snr -- Signal to Noise Ratio
Tx -- Transmit
Blks -- Blocks
Copyright (C) The Internet Society (2003). This version
of this MIB module is part of RFC XXXX: see the RFC
itself for full legal notices."
-- RFC Ed.: replace XXXX with assigned number & remove this note
REVISION "200306060000Z" -- June 6, 2003
DESCRIPTION "Initial version, published as RFC XXXX."
-- RFC Ed.: replace XXXX with assigned number & remove this note
::= { transmission YYYY }
-- RFC Ed.: replace YYYY with IANA-assigned number & remove this note
vdslLineMib OBJECT IDENTIFIER ::= { vdslMIB 1 }
vdslMibObjects OBJECT IDENTIFIER ::= { vdslLineMib 1 }
--
-- textual conventions used in this MIB
--
VdslLineCodingType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This data type is used as the syntax for the VDSL Line
Code. Attributes with this syntax identify the line coding
used. Specified as an INTEGER, the three values are:
Expires December 12, 2003 [Page 12]
INTERNET-DRAFT VDSL-LINE MIB June 2003
other(1) -- none of the following
mcm(2) -- Multiple Carrier Modulation
scm(3) -- Single Carrier Modulation"
SYNTAX INTEGER
{
other(1),
mcm(2),
scm(3)
}
VdslLineEntity ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Identifies a transceiver as being either Vtuc or Vtur.
A VDSL line consists of two transcievers, a Vtuc and a
Vtur. Attributes with this syntax reference the two sides
of a line. Specified as an INTEGER, the two values are:
vtuc(1) -- central site transceiver
vtur(2) -- remote site transceiver"
SYNTAX INTEGER
{
vtuc(1),
vtur(2)
}
--
-- objects
--
vdslLineTable OBJECT-TYPE
SYNTAX SEQUENCE OF VdslLineEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table includes common attributes describing
both ends of the line. It is required for all VDSL
physical interfaces. VDSL physical interfaces are
those ifEntries where ifType is equal to vdsl(97)."
::= { vdslMibObjects 1 }
vdslLineEntry OBJECT-TYPE
SYNTAX VdslLineEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "An entry in the vdslLineTable."
INDEX { ifIndex }
::= { vdslLineTable 1 }
VdslLineEntry ::=
SEQUENCE
{
Expires December 12, 2003 [Page 13]
INTERNET-DRAFT VDSL-LINE MIB June 2003
vdslLineCoding VdslLineCodingType,
vdslLineType INTEGER,
vdslLineConfProfile SnmpAdminString,
vdslLineAlarmConfProfile SnmpAdminString
}
vdslLineCoding OBJECT-TYPE
SYNTAX VdslLineCodingType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the VDSL coding type used on this line."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslLineEntry 1 }
vdslLineType OBJECT-TYPE
SYNTAX INTEGER
{
noChannel(1), -- no channels exist
fastOnly(2), -- only fast channel exists
interleavedOnly(3), -- only interleaved channel exists
fastOrInterleaved(4), -- either fast or interleaved channel
-- exist, but only one at a time
fastAndInterleaved(5) -- both fast and interleaved channels
-- exist
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Defines the type of VDSL physical line entity that exists,
by defining whether and how the line is channelized. If
the line is channelized, the value will be other than
noChannel(1). This object defines which channel type(s)
are supported. Defined values are:
noChannel(1) -- no channels exist
fastOnly(2) -- only fast channel exists
interleavedOnly(3) -- only interleaved channel exists
fastOrInterleaved(4) -- either fast or interleaved channel
-- exist, but only one at a time
fastAndInterleaved(5) -- both fast and interleaved channels
-- exist
In the case that the line is channelized, the manager
can use the ifStackTable to determine the ifIndex for
the associated channel(s)."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslLineEntry 2 }
vdslLineConfProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS read-write
Expires December 12, 2003 [Page 14]
INTERNET-DRAFT VDSL-LINE MIB June 2003
STATUS current
DESCRIPTION
"The value of this object identifies the row
in the VDSL Line Configuration Profile Table,
vdslLineConfProfileTable, which applies for this
VDSL line, and channels if applicable."
DEFVAL { "DEFVAL" }
::= { vdslLineEntry 3 }
vdslLineAlarmConfProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value of this object identifies the row in the VDSL
Line Alarm Configuration Profile Table,
vdslLineAlarmConfProfileTable, which applies to this
VDSL line, and channels if applicable."
DEFVAL { "DEFVAL" }
::= { vdslLineEntry 4 }
vdslPhysTable OBJECT-TYPE
SYNTAX SEQUENCE OF VdslPhysEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides one row for each Vtu. Each row
contains the Physical Layer Parameters table for that
Vtu. VDSL physical interfaces are those ifEntries where
ifType is equal to vdsl(97)."
::= { vdslMibObjects 2 }
vdslPhysEntry OBJECT-TYPE
SYNTAX VdslPhysEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "An entry in the vdslPhysTable."
INDEX { ifIndex,
vdslPhysSide }
::= { vdslPhysTable 1 }
VdslPhysEntry ::=
SEQUENCE
{
vdslPhysSide VdslLineEntity,
vdslInvSerialNumber SnmpAdminString,
vdslInvVendorID SnmpAdminString,
vdslInvVersionNumber SnmpAdminString,
vdslCurrSnrMgn Integer32,
vdslCurrAtn Gauge32,
vdslCurrStatus BITS,
vdslCurrOutputPwr Integer32,
Expires December 12, 2003 [Page 15]
INTERNET-DRAFT VDSL-LINE MIB June 2003
vdslCurrAttainableRate Gauge32,
vdslCurrLineRate Gauge32
}
vdslPhysSide OBJECT-TYPE
SYNTAX VdslLineEntity
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Identifies whether the transceiver is the Vtuc or Vtur."
::= { vdslPhysEntry 1 }
vdslInvSerialNumber OBJECT-TYPE
SYNTAX SnmpAdminString(SIZE (0..32))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The vendor specific string that identifies the
vendor equipment."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPhysEntry 2 }
vdslInvVendorID OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (0..16))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The vendor ID code is a copy of the binary vendor
identification field expressed as readable characters
in hexadecimal notation."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPhysEntry 3 }
vdslInvVersionNumber OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (0..16))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The vendor specific version number sent by this Vtu
as part of the initialization messages. It is a copy
of the binary version number field expressed as
readable characters in hexadecimal notation."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPhysEntry 4 }
vdslCurrSnrMgn OBJECT-TYPE
SYNTAX Integer32 (-127..127)
UNITS "0.25dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Noise Margin as seen by this Vtu with respect to its
Expires December 12, 2003 [Page 16]
INTERNET-DRAFT VDSL-LINE MIB June 2003
received signal in 0.25dB. The effective range is
-31.75 to +31.75 dB."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPhysEntry 5 }
vdslCurrAtn OBJECT-TYPE
SYNTAX Gauge32 (0..255)
UNITS "0.25dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Measured difference in the total power transmitted by
the peer Vtu and the total power received by this Vtu.
The effective range is 0 to +63.75 dB."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPhysEntry 6 }
vdslCurrStatus OBJECT-TYPE
SYNTAX BITS
{
noDefect(0),
lossOfFraming(1),
lossOfSignal(2),
lossOfPower(3),
lossOfSignalQuality(4),
lossOfLink(5),
dataInitFailure(6),
configInitFailure(7),
protocolInitFailure(8),
noPeerVtuPresent(9)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates current state of the Vtu line. This is a
bit-map of possible conditions. The various bit
positions are:
0 noDefect There are no defects on the line.
1 lossOfFraming Vtu failure due to not receiving
a valid frame.
2 lossOfSignal Vtu failure due to not receiving
signal.
3 lossOfPower Vtu failure due to loss of power.
4 lossOfSignalQuality Loss of Signal Quality is declared
when the Noise Margin falls below
the Minimum Noise Margin, or the
bit-error-rate exceeds 10^-7.
Expires December 12, 2003 [Page 17]
INTERNET-DRAFT VDSL-LINE MIB June 2003
5 lossOfLink Vtu failure due to inability to
link with peer Vtu. Set whenever
the transceiver is in the 'Warm
Start' state.
6 dataInitFailure Vtu failure during initialization
due to bit errors corrupting
startup exchange data.
7 configInitFailure Vtu failure during initialization
due to peer Vtu not able to
support requested configuration.
8 protocolInitFailure Vtu failure during initialization
due to incompatible protocol used
by the peer Vtu.
9 noPeerVtuPresent Vtu failure during initialization
due to no activation sequence
detected from peer Vtu.
This is intended to supplement ifOperStatus."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPhysEntry 7 }
vdslCurrOutputPwr OBJECT-TYPE
SYNTAX Integer32 (0..160)
UNITS "0.1dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Measured total output power transmitted by this VTU.
This is the measurement that was reported during
the last activation sequence."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPhysEntry 8 }
vdslCurrAttainableRate OBJECT-TYPE
SYNTAX Gauge32
UNITS "kbps"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the maximum currently attainable data rate
in steps of 1000 bits/second by the Vtu. This value
will be equal to or greater than vdslCurrLineRate.
Note that for SCM, the minimum and maximum data rates
are equal. Note: 1 kbps = 1000 bps."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPhysEntry 9 }
Expires December 12, 2003 [Page 18]
INTERNET-DRAFT VDSL-LINE MIB June 2003
vdslCurrLineRate OBJECT-TYPE
SYNTAX Gauge32
UNITS "kbps"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the current data rate in steps of 1000
bits/second by the Vtu. This value will be less than
or equal to vdslCurrAttainableRate. Note: 1 kbps =
1000 bps."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPhysEntry 10 }
vdslChanTable OBJECT-TYPE
SYNTAX SEQUENCE OF VdslChanEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides one row for each Vtu channel.
VDSL channel interfaces are those ifEntries where
ifType is equal to interleave(124) or fast(125)."
::= { vdslMibObjects 3 }
vdslChanEntry OBJECT-TYPE
SYNTAX VdslChanEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the vdslChanTable."
INDEX { ifIndex,
vdslPhysSide }
::= { vdslChanTable 1 }
VdslChanEntry ::=
SEQUENCE
{
vdslChanInterleaveDelay Gauge32,
vdslChanCrcBlockLength Gauge32,
vdslChanCurrTxRate Gauge32,
vdslChanCurrTxSlowBurstProtect Gauge32,
vdslChanCurrTxFastFec Gauge32
}
vdslChanInterleaveDelay OBJECT-TYPE
SYNTAX Gauge32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Interleave Delay for this channel.
Interleave delay applies only to the interleave
Expires December 12, 2003 [Page 19]
INTERNET-DRAFT VDSL-LINE MIB June 2003
(slow) channel and defines the mapping (relative
spacing) between subsequent input bytes at the
interleaver input and their placement in the bit
stream at the interleaver output. Larger numbers
provide greater separation between consecutive
input bytes in the output bit stream allowing for
improved impulse noise immunity at the expense of
payload latency.
In the case where the ifType is fast(125), return
a value of zero."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslChanEntry 1 }
vdslChanCrcBlockLength OBJECT-TYPE
SYNTAX Gauge32
UNITS "bytes"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the length of the channel data-block
on which the CRC operates."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslChanEntry 2 }
vdslChanCurrTxRate OBJECT-TYPE
SYNTAX Gauge32
UNITS "kbps"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Actual transmit data rate on this channel. Note: 1
kbps = 1000 bps."
::= { vdslChanEntry 3 }
vdslChanCurrTxSlowBurstProtect OBJECT-TYPE
SYNTAX Gauge32 (0..1275)
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Actual level of impulse noise (burst) protection
for an interleaved (slow) channel. This parameter is
not applicable to fast channels. For fast channels,
a value of zero shall be returned."
REFERENCE "ITU-T G.997.1, section 7.3.2.3"
::= { vdslChanEntry 4 }
vdslChanCurrTxFastFec OBJECT-TYPE
SYNTAX Gauge32 (0..50)
UNITS "%"
MAX-ACCESS read-only
Expires December 12, 2003 [Page 20]
INTERNET-DRAFT VDSL-LINE MIB June 2003
STATUS current
DESCRIPTION
"Actual Forward Error Correction (FEC) redundancy
related overhead for a fast channel. This parameter
is not applicable to an interleaved (slow) channel.
For interleaved channels, a value of zero shall be
returned."
::= { vdslChanEntry 5 }
vdslPerfDataTable OBJECT-TYPE
SYNTAX SEQUENCE OF VdslPerfDataEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides one row for each VDSL physical
interface. VDSL physical interfaces are those ifEntries
where ifType is equal to vdsl(97)."
::= { vdslMibObjects 4 }
vdslPerfDataEntry OBJECT-TYPE
SYNTAX VdslPerfDataEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the vdslPerfDataTable."
INDEX { ifIndex,
vdslPhysSide }
::= { vdslPerfDataTable 1 }
VdslPerfDataEntry ::=
SEQUENCE
{
vdslPerfValidIntervals HCPerfValidIntervals,
vdslPerfInvalidIntervals HCPerfInvalidIntervals,
vdslPerfLofs Unsigned32,
vdslPerfLoss Unsigned32,
vdslPerfLprs Unsigned32,
vdslPerfLols Unsigned32,
vdslPerfESs Unsigned32,
vdslPerfSESs Unsigned32,
vdslPerfUASs Unsigned32,
vdslPerfInits Unsigned32,
vdslPerfCurr15MinTimeElapsed HCPerfTimeElapsed,
vdslPerfCurr15MinLofs HCPerfCurrentCount,
vdslPerfCurr15MinLoss HCPerfCurrentCount,
vdslPerfCurr15MinLprs HCPerfCurrentCount,
vdslPerfCurr15MinLols HCPerfCurrentCount,
vdslPerfCurr15MinESs HCPerfCurrentCount,
vdslPerfCurr15MinSESs HCPerfCurrentCount,
vdslPerfCurr15MinUASs HCPerfCurrentCount,
vdslPerfCurr15MinInits HCPerfCurrentCount,
vdslPerf1DayValidIntervals HCPerfValidIntervals,
Expires December 12, 2003 [Page 21]
INTERNET-DRAFT VDSL-LINE MIB June 2003
vdslPerf1DayInvalidIntervals HCPerfInvalidIntervals,
vdslPerfCurr1DayTimeElapsed HCPerfTimeElapsed,
vdslPerfCurr1DayLofs Unsigned32,
vdslPerfCurr1DayLoss Unsigned32,
vdslPerfCurr1DayLprs Unsigned32,
vdslPerfCurr1DayLols Unsigned32,
vdslPerfCurr1DayESs Unsigned32,
vdslPerfCurr1DaySESs Unsigned32,
vdslPerfCurr1DayUASs Unsigned32,
vdslPerfCurr1DayInits Unsigned32
}
vdslPerfValidIntervals OBJECT-TYPE
SYNTAX HCPerfValidIntervals
UNITS "intervals"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Valid Intervals per definition found in
HC-PerfHist-TC-MIB."
::= { vdslPerfDataEntry 1 }
vdslPerfInvalidIntervals OBJECT-TYPE
SYNTAX HCPerfInvalidIntervals
UNITS "intervals"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Invalid Intervals per definition found in
HC-PerfHist-TC-MIB."
::= { vdslPerfDataEntry 2 }
vdslPerfLofs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds since the unit was last reset that there
was Loss of Framing."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPerfDataEntry 3 }
vdslPerfLoss OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds since the unit was last reset that there
was Loss of Signal."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
Expires December 12, 2003 [Page 22]
INTERNET-DRAFT VDSL-LINE MIB June 2003
::= { vdslPerfDataEntry 4 }
vdslPerfLprs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds since the unit was last reset that there
was Loss of Power."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPerfDataEntry 5 }
vdslPerfLols OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds since the unit was last reset that there
was Loss of Link."
::= { vdslPerfDataEntry 6 }
vdslPerfESs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Errored Seconds since the unit was last reset.
An Errored Second is a one-second interval containing one
or more CRC anomalies, or one or more LOS or LOF defects."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPerfDataEntry 7 }
vdslPerfSESs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Severely Errored Seconds since the unit was last
reset."
::= { vdslPerfDataEntry 8 }
vdslPerfUASs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Unavailable Seconds since the unit was last
Expires December 12, 2003 [Page 23]
INTERNET-DRAFT VDSL-LINE MIB June 2003
reset."
::= { vdslPerfDataEntry 9 }
vdslPerfInits OBJECT-TYPE
SYNTAX Unsigned32
UNITS "occurences"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of the line initialization attempts since the unit
was last reset. This count includes both successful and
failed attempts."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPerfDataEntry 10 }
vdslPerfCurr15MinTimeElapsed OBJECT-TYPE
SYNTAX HCPerfTimeElapsed
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total elapsed seconds in this interval."
::= { vdslPerfDataEntry 11 }
vdslPerfCurr15MinLofs OBJECT-TYPE
SYNTAX HCPerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval that there
was Loss of Framing."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPerfDataEntry 12 }
vdslPerfCurr15MinLoss OBJECT-TYPE
SYNTAX HCPerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval that there
was Loss of Signal."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPerfDataEntry 13 }
vdslPerfCurr15MinLprs OBJECT-TYPE
SYNTAX HCPerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
Expires December 12, 2003 [Page 24]
INTERNET-DRAFT VDSL-LINE MIB June 2003
"Count of seconds during this interval that there
was Loss of Power."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPerfDataEntry 14 }
vdslPerfCurr15MinLols OBJECT-TYPE
SYNTAX HCPerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval that there
was Loss of Link."
::= { vdslPerfDataEntry 15 }
vdslPerfCurr15MinESs OBJECT-TYPE
SYNTAX HCPerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Errored Seconds during this interval. An Errored
Second is a one-second interval containing one or more CRC
anomalies, or one or more LOS or LOF defects."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPerfDataEntry 16 }
vdslPerfCurr15MinSESs OBJECT-TYPE
SYNTAX HCPerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Severely Errored Seconds during this interval."
::= { vdslPerfDataEntry 17 }
vdslPerfCurr15MinUASs OBJECT-TYPE
SYNTAX HCPerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Unavailable Seconds during this interval."
::= { vdslPerfDataEntry 18 }
vdslPerfCurr15MinInits OBJECT-TYPE
SYNTAX HCPerfCurrentCount
UNITS "occurences"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of the line initialization attempts during this
Expires December 12, 2003 [Page 25]
INTERNET-DRAFT VDSL-LINE MIB June 2003
interval. This count includes both successful and
failed attempts."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPerfDataEntry 19 }
vdslPerf1DayValidIntervals OBJECT-TYPE
SYNTAX HCPerfValidIntervals
UNITS "intervals"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Valid Intervals per definition found in
HC-PerfHist-TC-MIB."
::= { vdslPerfDataEntry 20 }
vdslPerf1DayInvalidIntervals OBJECT-TYPE
SYNTAX HCPerfInvalidIntervals
UNITS "intervals"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Invalid Intervals per definition found in
HC-PerfHist-TC-MIB."
::= { vdslPerfDataEntry 21 }
vdslPerfCurr1DayTimeElapsed OBJECT-TYPE
SYNTAX HCPerfTimeElapsed
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of seconds that have elapsed since the beginning
of the current 1-day interval."
::= { vdslPerfDataEntry 22 }
vdslPerfCurr1DayLofs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Loss of Framing (LOF) Seconds since the
beginning of the current 1-day interval."
::= { vdslPerfDataEntry 23 }
vdslPerfCurr1DayLoss OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Loss of Signal (LOS) Seconds since the beginning
Expires December 12, 2003 [Page 26]
INTERNET-DRAFT VDSL-LINE MIB June 2003
of the current 1-day interval."
::= { vdslPerfDataEntry 24 }
vdslPerfCurr1DayLprs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Loss of Power (LPR) Seconds since the beginning
of the current 1-day interval."
::= { vdslPerfDataEntry 25 }
vdslPerfCurr1DayLols OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Loss of Link (LOL) Seconds since the beginning
of the current 1-day interval."
::= { vdslPerfDataEntry 26 }
vdslPerfCurr1DayESs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Errored Seconds (ES) since the beginning
of the current 1-day interval."
::= { vdslPerfDataEntry 27 }
vdslPerfCurr1DaySESs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Severely Errored Seconds (SES) since the
beginning of the current 1-day interval."
::= { vdslPerfDataEntry 28 }
vdslPerfCurr1DayUASs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Unavailable Seconds (UAS) since the beginning
of the current 1-day interval."
::= { vdslPerfDataEntry 29 }
Expires December 12, 2003 [Page 27]
INTERNET-DRAFT VDSL-LINE MIB June 2003
vdslPerfCurr1DayInits OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of the line initialization attempts since the
beginning of the current 1-day interval. This count
includes both successful and failed attempts."
::= { vdslPerfDataEntry 30 }
vdslPerfIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF VdslPerfIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides one row for each Vtu performance
data collection interval. VDSL physical interfaces are
those ifEntries where ifType is equal to vdsl(97)."
::= { vdslMibObjects 5 }
vdslPerfIntervalEntry OBJECT-TYPE
SYNTAX VdslPerfIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the vdslPerfIntervalTable."
INDEX { ifIndex,
vdslPhysSide,
vdslIntervalNumber }
::= { vdslPerfIntervalTable 1 }
VdslPerfIntervalEntry ::=
SEQUENCE
{
vdslIntervalNumber Unsigned32,
vdslIntervalLofs HCPerfIntervalCount,
vdslIntervalLoss HCPerfIntervalCount,
vdslIntervalLprs HCPerfIntervalCount,
vdslIntervalLols HCPerfIntervalCount,
vdslIntervalESs HCPerfIntervalCount,
vdslIntervalSESs HCPerfIntervalCount,
vdslIntervalUASs HCPerfIntervalCount,
vdslIntervalInits HCPerfIntervalCount
}
vdslIntervalNumber OBJECT-TYPE
SYNTAX Unsigned32 (1..96)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
Expires December 12, 2003 [Page 28]
INTERNET-DRAFT VDSL-LINE MIB June 2003
"Performance Data Interval number 1 is the most recent
previous interval; interval 96 is 24 hours ago.
Intervals 2 to 96 are optional."
::= { vdslPerfIntervalEntry 1 }
vdslIntervalLofs OBJECT-TYPE
SYNTAX HCPerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds in the interval when there was Loss
of Framing."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPerfIntervalEntry 2 }
vdslIntervalLoss OBJECT-TYPE
SYNTAX HCPerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds in the interval when there was Loss
of Signal."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPerfIntervalEntry 3 }
vdslIntervalLprs OBJECT-TYPE
SYNTAX HCPerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds in the interval when there was Loss
of Power."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPerfIntervalEntry 4 }
vdslIntervalLols OBJECT-TYPE
SYNTAX HCPerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds in the interval when there was Loss
of Link."
::= { vdslPerfIntervalEntry 5 }
vdslIntervalESs OBJECT-TYPE
SYNTAX HCPerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
Expires December 12, 2003 [Page 29]
INTERNET-DRAFT VDSL-LINE MIB June 2003
STATUS current
DESCRIPTION
"Count of Errored Seconds (ES) in the interval. An Errored
Second is a one-second interval containing one or more CRC
anomalies, one or more LOS or LOF defects."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPerfIntervalEntry 6 }
vdslIntervalSESs OBJECT-TYPE
SYNTAX HCPerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Severely Errored Seconds in the interval."
::= { vdslPerfIntervalEntry 7 }
vdslIntervalUASs OBJECT-TYPE
SYNTAX HCPerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Unavailable Seconds in the interval."
::= { vdslPerfIntervalEntry 8 }
vdslIntervalInits OBJECT-TYPE
SYNTAX HCPerfIntervalCount
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of the line initialization attempts during this
interval. This count includes both successful and
failed attempts."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslPerfIntervalEntry 9 }
vdsl1DayIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF Vdsl1DayIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides one row for each VDSL performance
data collection interval. This table contains live data
from equipment. As such, it is NOT persistent."
::= { vdslMibObjects 6 }
vdsl1DayIntervalEntry OBJECT-TYPE
SYNTAX Vdsl1DayIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
Expires December 12, 2003 [Page 30]
INTERNET-DRAFT VDSL-LINE MIB June 2003
"An entry in the vdsl1DayIntervalTable."
INDEX { ifIndex,
vdslPhysSide,
vdsl1DayIntervalNumber }
::= { vdsl1DayIntervalTable 1 }
Vdsl1DayIntervalEntry ::=
SEQUENCE
{
vdsl1DayIntervalNumber Unsigned32,
vdsl1DayIntervalMoniSecs HCPerfTimeElapsed,
vdsl1DayIntervalLofs Unsigned32,
vdsl1DayIntervalLoss Unsigned32,
vdsl1DayIntervalLprs Unsigned32,
vdsl1DayIntervalLols Unsigned32,
vdsl1DayIntervalESs Unsigned32,
vdsl1DayIntervalSESs Unsigned32,
vdsl1DayIntervalUASs Unsigned32,
vdsl1DayIntervalInits Unsigned32
}
vdsl1DayIntervalNumber OBJECT-TYPE
SYNTAX Unsigned32 (1..30)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"History Data Interval number. Interval 1 is the most
recent previous day; interval 30 is 30 days ago. Intervals
2 to 30 are optional."
::= { vdsl1DayIntervalEntry 1 }
vdsl1DayIntervalMoniSecs OBJECT-TYPE
SYNTAX HCPerfTimeElapsed
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The amount of time in the 1-day interval over which the
performance monitoring information is actually counted.
This value will be the same as the interval duration except
in a situation where performance monitoring data could not
be collected for any reason."
::= { vdsl1DayIntervalEntry 2 }
vdsl1DayIntervalLofs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Loss of Frame (LOF) Seconds during the 1-day
interval as measured by vdsl1DayIntervalMoniSecs."
Expires December 12, 2003 [Page 31]
INTERNET-DRAFT VDSL-LINE MIB June 2003
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdsl1DayIntervalEntry 3 }
vdsl1DayIntervalLoss OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Loss of Signal (LOS) Seconds during the 1-day
interval as measured by vdsl1DayIntervalMoniSecs."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdsl1DayIntervalEntry 4 }
vdsl1DayIntervalLprs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Loss of Power (LPR) Seconds during the 1-day
interval as measured by vdsl1DayIntervalMoniSecs."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdsl1DayIntervalEntry 5 }
vdsl1DayIntervalLols OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Loss of Link (LOL) Seconds during the 1-day
interval as measured by vdsl1DayIntervalMoniSecs."
::= { vdsl1DayIntervalEntry 6 }
vdsl1DayIntervalESs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Errored Seconds (ES) during the 1-day
interval as measured by vdsl1DayIntervalMoniSecs."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdsl1DayIntervalEntry 7 }
vdsl1DayIntervalSESs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
Expires December 12, 2003 [Page 32]
INTERNET-DRAFT VDSL-LINE MIB June 2003
"Count of Severely Errored Seconds (SES) during the 1-day
interval as measured by vdsl1DayIntervalMoniSecs."
::= { vdsl1DayIntervalEntry 8 }
vdsl1DayIntervalUASs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Unavailable Seconds (UAS) during the 1-day
interval as measured by vdsl1DayIntervalMoniSecs."
::= { vdsl1DayIntervalEntry 9 }
vdsl1DayIntervalInits OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of the line initialization attempts during the
1-day interval as measured by vdsl1DayIntervalMoniSecs.
This count includes both successful and failed attempts."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdsl1DayIntervalEntry 10 }
vdslChanPerfDataTable OBJECT-TYPE
SYNTAX SEQUENCE OF VdslChanPerfDataEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides one row for each Vtu channel.
VDSL channel interfaces are those ifEntries where
ifType is equal to interleave(124) or fast(125)."
::= { vdslMibObjects 7 }
vdslChanPerfDataEntry OBJECT-TYPE
SYNTAX VdslChanPerfDataEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the vdslChanPerfDataTable."
INDEX { ifIndex,
vdslPhysSide }
::= { vdslChanPerfDataTable 1 }
VdslChanPerfDataEntry ::=
SEQUENCE
{
vdslChanValidIntervals HCPerfValidIntervals,
vdslChanInvalidIntervals HCPerfInvalidIntervals,
vdslChanFixedOctets ZeroBasedCounter64,
Expires December 12, 2003 [Page 33]
INTERNET-DRAFT VDSL-LINE MIB June 2003
vdslChanBadBlks ZeroBasedCounter64,
vdslChanCurr15MinTimeElapsed HCPerfTimeElapsed,
vdslChanCurr15MinFixedOctets HCPerfCurrentCount,
vdslChanCurr15MinBadBlks HCPerfCurrentCount,
vdslChan1DayValidIntervals HCPerfValidIntervals,
vdslChan1DayInvalidIntervals HCPerfInvalidIntervals,
vdslChanCurr1DayTimeElapsed HCPerfTimeElapsed,
vdslChanCurr1DayFixedOctets HCPerfCurrentCount,
vdslChanCurr1DayBadBlks HCPerfCurrentCount
}
vdslChanValidIntervals OBJECT-TYPE
SYNTAX HCPerfValidIntervals
UNITS "intervals"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Valid Intervals per definition found in
HC-PerfHist-TC-MIB."
::= { vdslChanPerfDataEntry 1 }
vdslChanInvalidIntervals OBJECT-TYPE
SYNTAX HCPerfInvalidIntervals
UNITS "intervals"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Invalid Intervals per definition found in
HC-PerfHist-TC-MIB."
::= { vdslChanPerfDataEntry 2 }
vdslChanFixedOctets OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of corrected octets since the unit was last reset."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslChanPerfDataEntry 3 }
vdslChanBadBlks OBJECT-TYPE
SYNTAX ZeroBasedCounter64
UNITS "blocks"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of uncorrectable blocks since the unit was last
reset."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslChanPerfDataEntry 4 }
Expires December 12, 2003 [Page 34]
INTERNET-DRAFT VDSL-LINE MIB June 2003
vdslChanCurr15MinTimeElapsed OBJECT-TYPE
SYNTAX HCPerfTimeElapsed
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total elapsed seconds in this interval."
::= { vdslChanPerfDataEntry 5 }
vdslChanCurr15MinFixedOctets OBJECT-TYPE
SYNTAX HCPerfCurrentCount
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of corrected octets in this interval."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslChanPerfDataEntry 6 }
vdslChanCurr15MinBadBlks OBJECT-TYPE
SYNTAX HCPerfCurrentCount
UNITS "blocks"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of uncorrectable blocks in this interval."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslChanPerfDataEntry 7 }
vdslChan1DayValidIntervals OBJECT-TYPE
SYNTAX HCPerfValidIntervals
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Valid Intervals per definition found in
HC-PerfHist-TC-MIB."
::= { vdslChanPerfDataEntry 8 }
vdslChan1DayInvalidIntervals OBJECT-TYPE
SYNTAX HCPerfInvalidIntervals
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Invalid Intervals per definition found in
HC-PerfHist-TC-MIB."
::= { vdslChanPerfDataEntry 9 }
vdslChanCurr1DayTimeElapsed OBJECT-TYPE
SYNTAX HCPerfTimeElapsed
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
Expires December 12, 2003 [Page 35]
INTERNET-DRAFT VDSL-LINE MIB June 2003
DESCRIPTION
"Number of seconds that have elapsed since the beginning
of the current 1-day interval."
::= { vdslChanPerfDataEntry 10 }
vdslChanCurr1DayFixedOctets OBJECT-TYPE
SYNTAX HCPerfCurrentCount
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of corrected octets since the beginning of the
current 1-day interval."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslChanPerfDataEntry 11 }
vdslChanCurr1DayBadBlks OBJECT-TYPE
SYNTAX HCPerfCurrentCount
UNITS "blocks"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of uncorrectable blocks since the beginning of the
current 1-day interval."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslChanPerfDataEntry 12 }
vdslChanIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF VdslChanIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides one row for each Vtu channel data
collection interval. VDSL channel interfaces are those
ifEntries where ifType is equal to interleave(124) or
fast(125)."
::= { vdslMibObjects 8 }
vdslChanIntervalEntry OBJECT-TYPE
SYNTAX VdslChanIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the vdslChanIntervalTable."
INDEX { ifIndex,
vdslPhysSide,
vdslChanIntervalNumber }
::= { vdslChanIntervalTable 1 }
VdslChanIntervalEntry ::=
SEQUENCE
{
Expires December 12, 2003 [Page 36]
INTERNET-DRAFT VDSL-LINE MIB June 2003
vdslChanIntervalNumber Unsigned32,
vdslChanIntervalFixedOctets HCPerfIntervalCount,
vdslChanIntervalBadBlks HCPerfIntervalCount
}
vdslChanIntervalNumber OBJECT-TYPE
SYNTAX Unsigned32 (1..96)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Performance Data Interval number 1 is the most recent
previous interval; interval 96 is 24 hours ago.
Intervals 2 to 96 are optional."
::= { vdslChanIntervalEntry 1 }
vdslChanIntervalFixedOctets OBJECT-TYPE
SYNTAX HCPerfIntervalCount
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of corrected octets in this interval."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslChanIntervalEntry 2 }
vdslChanIntervalBadBlks OBJECT-TYPE
SYNTAX HCPerfIntervalCount
UNITS "blocks"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of uncorrectable blocks in this interval."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslChanIntervalEntry 3 }
vdslChan1DayIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF VdslChan1DayIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides one row for each VDSL performance
data collection interval. This table contains live data
from equipment. As such, it is NOT persistent."
::= { vdslMibObjects 9 }
vdslChan1DayIntervalEntry OBJECT-TYPE
SYNTAX VdslChan1DayIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the vdslChan1DayIntervalTable."
INDEX { ifIndex,
Expires December 12, 2003 [Page 37]
INTERNET-DRAFT VDSL-LINE MIB June 2003
vdslPhysSide,
vdslChan1DayIntervalNumber }
::= { vdslChan1DayIntervalTable 1 }
VdslChan1DayIntervalEntry ::=
SEQUENCE
{
vdslChan1DayIntervalNumber Unsigned32,
vdslChan1DayIntervalMoniSecs HCPerfTimeElapsed,
vdslChan1DayIntervalFixedOctets HCPerfCurrentCount,
vdslChan1DayIntervalBadBlks HCPerfCurrentCount
}
vdslChan1DayIntervalNumber OBJECT-TYPE
SYNTAX Unsigned32 (1..30)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"History Data Interval number. Interval 1 is the most
recent previous day; interval 30 is 30 days ago. Intervals
2 to 30 are optional."
::= { vdslChan1DayIntervalEntry 1 }
vdslChan1DayIntervalMoniSecs OBJECT-TYPE
SYNTAX HCPerfTimeElapsed
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The amount of time in the 1-day interval over which the
performance monitoring information is actually counted.
This value will be the same as the interval duration except
in a situation where performance monitoring data could not
be collected for any reason."
::= { vdslChan1DayIntervalEntry 2 }
vdslChan1DayIntervalFixedOctets OBJECT-TYPE
SYNTAX HCPerfCurrentCount
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of corrected octets in this interval."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslChan1DayIntervalEntry 3 }
vdslChan1DayIntervalBadBlks OBJECT-TYPE
SYNTAX HCPerfCurrentCount
UNITS "blocks"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
Expires December 12, 2003 [Page 38]
INTERNET-DRAFT VDSL-LINE MIB June 2003
"Count of uncorrectable blocks in this interval."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
::= { vdslChan1DayIntervalEntry 4 }
--
-- profile tables
--
vdslLineConfProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF VdslLineConfProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains information on the VDSL line
configuration. One entry in this table reflects a
profile defined by a manager which can be used to
configure the VDSL line."
::= { vdslMibObjects 11 }
vdslLineConfProfileEntry OBJECT-TYPE
SYNTAX VdslLineConfProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry consists of a list of parameters that
represents the configuration of a VDSL line.
A default profile with an index of 'DEFVAL', will
always exist and its parameters will be set to vendor
specific values, unless otherwise specified in this
document."
INDEX { vdslLineConfProfileName }
::= { vdslLineConfProfileTable 1 }
VdslLineConfProfileEntry ::=
SEQUENCE
{
vdslLineConfProfileName SnmpAdminString,
vdslLineConfDownRateMode INTEGER,
vdslLineConfUpRateMode INTEGER,
vdslLineConfDownMaxPwr Unsigned32,
vdslLineConfUpMaxPwr Unsigned32,
vdslLineConfDownMaxSnrMgn Unsigned32,
vdslLineConfDownMinSnrMgn Unsigned32,
vdslLineConfDownTargetSnrMgn Unsigned32,
vdslLineConfUpMaxSnrMgn Unsigned32,
vdslLineConfUpMinSnrMgn Unsigned32,
vdslLineConfUpTargetSnrMgn Unsigned32,
vdslLineConfDownFastMaxDataRate Unsigned32,
vdslLineConfDownFastMinDataRate Unsigned32,
vdslLineConfDownSlowMaxDataRate Unsigned32,
vdslLineConfDownSlowMinDataRate Unsigned32,
Expires December 12, 2003 [Page 39]
INTERNET-DRAFT VDSL-LINE MIB June 2003
vdslLineConfUpFastMaxDataRate Unsigned32,
vdslLineConfUpFastMinDataRate Unsigned32,
vdslLineConfUpSlowMaxDataRate Unsigned32,
vdslLineConfUpSlowMinDataRate Unsigned32,
vdslLineConfDownRateRatio Unsigned32,
vdslLineConfUpRateRatio Unsigned32,
vdslLineConfDownMaxInterDelay Unsigned32,
vdslLineConfUpMaxInterDelay Unsigned32,
vdslLineConfDownPboControl INTEGER,
vdslLineConfUpPboControl INTEGER,
vdslLineConfDownPboLevel Unsigned32,
vdslLineConfUpPboLevel Unsigned32,
vdslLineConfDeploymentScenario INTEGER,
vdslLineConfAdslPresence INTEGER,
vdslLineConfApplicableStandard INTEGER,
vdslLineConfBandPlan INTEGER,
vdslLineConfBandPlanFx Unsigned32,
vdslLineConfBandOptUsage INTEGER,
vdslLineConfUpPsdTemplate INTEGER,
vdslLineConfDownPsdTemplate INTEGER,
vdslLineConfHamBandMask BITS,
vdslLineConfCustomNotch1Start Unsigned32,
vdslLineConfCustomNotch1Stop Unsigned32,
vdslLineConfCustomNotch2Start Unsigned32,
vdslLineConfCustomNotch2Stop Unsigned32,
vdslLineConfDownTargetSlowBurst Unsigned32,
vdslLineConfUpTargetSlowBurst Unsigned32,
vdslLineConfDownMaxFastFec Unsigned32,
vdslLineConfUpMaxFastFec Unsigned32,
vdslLineConfLineType INTEGER,
vdslLineConfProfRowStatus RowStatus
}
vdslLineConfProfileName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (1..32))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object identifies a row in this table.
A default profile with an index of 'DEFVAL', will
always exist and its parameters will be set to vendor
specific values, unless otherwise specified in this
document."
::= { vdslLineConfProfileEntry 1 }
vdslLineConfDownRateMode OBJECT-TYPE
SYNTAX INTEGER
{
manual(1),
adaptAtInit(2)
}
Expires December 12, 2003 [Page 40]
INTERNET-DRAFT VDSL-LINE MIB June 2003
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the rate selection behavior for the line
in the downstream direction.
manual(1) forces the rate to the configured rate
adaptAtInit(2) adapts the line based upon line quality."
DEFVAL { adaptAtInit }
::= { vdslLineConfProfileEntry 2 }
vdslLineConfUpRateMode OBJECT-TYPE
SYNTAX INTEGER
{
manual(1),
adaptAtInit(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the rate selection behavior for the line
in the upstream direction.
manual(1) forces the rate to the configured rate
adaptAtInit(2) adapts the line based upon line quality."
DEFVAL { adaptAtInit }
::= { vdslLineConfProfileEntry 3 }
vdslLineConfDownMaxPwr OBJECT-TYPE
SYNTAX Unsigned32 (0..58)
UNITS "0.25dBm"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the maximum aggregate downstream power
level in the range 0 to 14.5 dBm."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
DEFVAL { 0 }
::= { vdslLineConfProfileEntry 4 }
vdslLineConfUpMaxPwr OBJECT-TYPE
SYNTAX Unsigned32 (0..58)
UNITS "0.25dBm"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the maximum aggregate upstream power
level in the range 0 to 14.5 dBm."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
DEFVAL { 0 }
::= { vdslLineConfProfileEntry 5 }
Expires December 12, 2003 [Page 41]
INTERNET-DRAFT VDSL-LINE MIB June 2003
vdslLineConfDownMaxSnrMgn OBJECT-TYPE
SYNTAX Unsigned32 (0..127)
UNITS "0.25dBm"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the maximum downstream Signal/Noise Margin
in units of 0.25 dB, for a range of 0 to 31.75 dB."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
DEFVAL { 0 }
::= { vdslLineConfProfileEntry 6 }
vdslLineConfDownMinSnrMgn OBJECT-TYPE
SYNTAX Unsigned32 (0..127)
UNITS "0.25dBm"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the minimum downstream Signal/Noise Margin
in units of 0.25 dB, for a range of 0 to 31.75 dB."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
DEFVAL { 0 }
::= { vdslLineConfProfileEntry 7 }
vdslLineConfDownTargetSnrMgn OBJECT-TYPE
SYNTAX Unsigned32 (0..127)
UNITS "0.25dBm"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the target downstream Signal/Noise Margin
in units of 0.25 dB, for a range of 0 to 31.75 dB.
This is the Noise Margin the transceivers must achieve
with a BER of 10^-7 or better to successfully complete
initialization."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
DEFVAL { 0 }
::= { vdslLineConfProfileEntry 8 }
vdslLineConfUpMaxSnrMgn OBJECT-TYPE
SYNTAX Unsigned32 (0..127)
UNITS "0.25dBm"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the maximum upstream Signal/Noise Margin
in units of 0.25 dB, for a range of 0 to 31.75 dB."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
DEFVAL { 0 }
::= { vdslLineConfProfileEntry 9 }
vdslLineConfUpMinSnrMgn OBJECT-TYPE
Expires December 12, 2003 [Page 42]
INTERNET-DRAFT VDSL-LINE MIB June 2003
SYNTAX Unsigned32 (0..127)
UNITS "0.25dBm"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the minimum upstream Signal/Noise Margin
in units of 0.25 dB, for a range of 0 to 31.75 dB."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
DEFVAL { 0 }
::= { vdslLineConfProfileEntry 10 }
vdslLineConfUpTargetSnrMgn OBJECT-TYPE
SYNTAX Unsigned32 (0..127)
UNITS "0.25dBm"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the target upstream Signal/Noise Margin in
units of 0.25 dB, for a range of 0 to 31.75 dB. This
is the Noise Margin the transceivers must achieve with
a BER of 10^-7 or better to successfully complete
initialization."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
DEFVAL { 0 }
::= { vdslLineConfProfileEntry 11 }
vdslLineConfDownFastMaxDataRate OBJECT-TYPE
SYNTAX Unsigned32
UNITS "kbps"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the maximum downstream fast channel
data rate in steps of 1000 bits/second."
DEFVAL { 0 }
::= { vdslLineConfProfileEntry 12 }
vdslLineConfDownFastMinDataRate OBJECT-TYPE
SYNTAX Unsigned32
UNITS "kbps"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the minimum downstream fast channel
data rate in steps of 1000 bits/second."
DEFVAL { 0 }
::= { vdslLineConfProfileEntry 13 }
vdslLineConfDownSlowMaxDataRate OBJECT-TYPE
SYNTAX Unsigned32
UNITS "kbps"
MAX-ACCESS read-create
Expires December 12, 2003 [Page 43]
INTERNET-DRAFT VDSL-LINE MIB June 2003
STATUS current
DESCRIPTION
"Specifies the maximum downstream slow channel
data rate in steps of 1000 bits/second.
The maximum aggregate downstream transmit speed
of the line can be derived from the sum of maximum
downstream fast and slow channel data rates."
DEFVAL { 0 }
::= { vdslLineConfProfileEntry 14 }
vdslLineConfDownSlowMinDataRate OBJECT-TYPE
SYNTAX Unsigned32
UNITS "kbps"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the minimum downstream slow channel
data rate in steps of 1000 bits/second.
The minimum aggregate downstream transmit speed
of the line can be derived from the sum of minimum
downstream fast and slow channel data rates."
DEFVAL { 0 }
::= { vdslLineConfProfileEntry 15 }
vdslLineConfUpFastMaxDataRate OBJECT-TYPE
SYNTAX Unsigned32
UNITS "kbps"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the maximum upstream fast channel
data rate in steps of 1000 bits/second.
The maximum aggregate upstream transmit speed
of the line can be derived from the sum of maximum
upstream fast and slow channel data rates."
DEFVAL { 0 }
::= { vdslLineConfProfileEntry 16 }
vdslLineConfUpFastMinDataRate OBJECT-TYPE
SYNTAX Unsigned32
UNITS "kbps"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the minimum upstream fast channel
data rate in steps of 1000 bits/second.
The minimum aggregate upstream transmit speed
of the line can be derived from the sum of minimum
Expires December 12, 2003 [Page 44]
INTERNET-DRAFT VDSL-LINE MIB June 2003
upstream fast and slow channel data rates."
DEFVAL { 0 }
::= { vdslLineConfProfileEntry 17 }
vdslLineConfUpSlowMaxDataRate OBJECT-TYPE
SYNTAX Unsigned32
UNITS "kbps"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the maximum upstream slow channel
data rate in steps of 1000 bits/second."
DEFVAL { 0 }
::= { vdslLineConfProfileEntry 18 }
vdslLineConfUpSlowMinDataRate OBJECT-TYPE
SYNTAX Unsigned32
UNITS "kbps"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the minimum upstream slow channel
data rate in steps of 1000 bits/second."
DEFVAL { 0 }
::= { vdslLineConfProfileEntry 19 }
vdslLineConfDownRateRatio OBJECT-TYPE
SYNTAX Unsigned32 (0..100)
UNITS "percent"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"For dynamic rate adaptation at startup, the allocation
of data rate in excess of the minimum data rate for each
channel is controlled by the object. This object specifies
the ratio of the allocation of the excess data rate between
the fast and the slow channels. This allocation represents
downstream Fast Channel Allocation / Slow Channel
Allocation."
DEFVAL { 0 }
::= { vdslLineConfProfileEntry 20 }
vdslLineConfUpRateRatio OBJECT-TYPE
SYNTAX Unsigned32 (0..100)
UNITS "percent"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"For dynamic rate adaptation at startup, the allocation
of data rate in excess of the minimum data rate for each
channel is controlled by the object. This object specifies
the ratio of the allocation of the excess data rate between
Expires December 12, 2003 [Page 45]
INTERNET-DRAFT VDSL-LINE MIB June 2003
the fast and the slow channels. This allocation represents
upstream Fast Channel Allocation/Slow Channel Allocation."
DEFVAL { 0 }
::= { vdslLineConfProfileEntry 21 }
vdslLineConfDownMaxInterDelay OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
UNITS "milliseconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the maximum interleave delay for the
downstream slow channel."
DEFVAL { 0 }
::= { vdslLineConfProfileEntry 22 }
vdslLineConfUpMaxInterDelay OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
UNITS "milliseconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the maximum interleave delay for the
upstream slow channel."
DEFVAL { 0 }
::= { vdslLineConfProfileEntry 23 }
vdslLineConfDownPboControl OBJECT-TYPE
SYNTAX INTEGER
{
disabled(1),
auto(2),
manual(3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Downstream power backoff (PBO) control for this
line. For transceivers which do not support downstream
PBO control, this object MUST be fixed at disabled(1).
If auto(2) is selected, the transceiver will automatically
adjust the power backoff. If manual(3) is selected,
then the transceiver will use the value from
vdslLineConfDownPboLevel."
DEFVAL { disabled }
::= { vdslLineConfProfileEntry 24 }
vdslLineConfUpPboControl OBJECT-TYPE
SYNTAX INTEGER
{
disabled(1),
auto(2),
Expires December 12, 2003 [Page 46]
INTERNET-DRAFT VDSL-LINE MIB June 2003
manual(3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Upstream power backoff (PBO) control for this
line. For transceivers which do not support upstream
PBO control, this object MUST be fixed at disabled(1).
If auto(2) is selected, the transceiver will automatically
adjust the power backoff. If manual(3) is selected,
then the transceiver will use the value from
vdslLineConfUpPboLevel."
DEFVAL { disabled }
::= { vdslLineConfProfileEntry 25 }
vdslLineConfDownPboLevel OBJECT-TYPE
SYNTAX Unsigned32 (0..160)
UNITS "0.25dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the downstream backoff level to be used
when vdslLineConfDownPboControl = manual(3)."
DEFVAL { 0 }
::= { vdslLineConfProfileEntry 26 }
vdslLineConfUpPboLevel OBJECT-TYPE
SYNTAX Unsigned32 (0..160)
UNITS "0.25dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the upstream backoff level to be used
when vdslLineConfUpPboControl = manual(3)."
DEFVAL { 0 }
::= { vdslLineConfProfileEntry 27 }
vdslLineConfDeploymentScenario OBJECT-TYPE
SYNTAX INTEGER
{
fttCab(1),
fttEx(2),
other(3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The VDSL line deployment scenario. When using
fttCab(1), the VTU-C is located in a street cabinet.
When using fttEx(2), the VTU-C is located at the
central office. Changes to this value will have
no effect on the transceiver."
Expires December 12, 2003 [Page 47]
INTERNET-DRAFT VDSL-LINE MIB June 2003
REFERENCE "DSL Forum TR-057"
DEFVAL { fttCab }
::= { vdslLineConfProfileEntry 28 }
vdslLineConfAdslPresence OBJECT-TYPE
SYNTAX INTEGER
{
none(1),
adslOverPots(2),
adslOverISDN(3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates presence of ADSL service in the associated
cable bundle/binder.
none(1) indicates no ADSL service in the bundle
adslOverPots(2) indicates ADSL service over POTS is
present in the bundle
adslOverISDN(3) indicates ADSL service over ISDN is
present in the bundle"
DEFVAL { none }
::= { vdslLineConfProfileEntry 29 }
vdslLineConfApplicableStandard OBJECT-TYPE
SYNTAX INTEGER
{
ansi(1),
etsi(2),
itu(3),
other(4)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The VDSL standard to be used for the line.
ansi(1) indicates ANSI standard
etsi(2) indicates ETSI standard
itu(3) indicates ITU standard
other(4) indicates a standard other than the above."
DEFVAL { ansi }
::= { vdslLineConfProfileEntry 30 }
vdslLineConfBandPlan OBJECT-TYPE
SYNTAX INTEGER
{
bandPlan997(1),
bandPlan998(2),
bandPlanFx(3),
other(4)
Expires December 12, 2003 [Page 48]
INTERNET-DRAFT VDSL-LINE MIB June 2003
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The VDSL band plan to be used for the line.
bandPlan997(1) is to be used for
ITU-T G.993.1 Bandplan-B
ETSI Bandplan
ANSI Plan 997
bandPlan998(2) is to be used for
ITU-T G.993.1 Bandplan-A
ANSI Plan 998
bandPlanFx(3) is to be used for
ITU-T G.993.1 Bandplan-C.
other(4) is to be used for
non-standard bandplans.
If this object is set to bandPlanFx(3), then the
object vdslLineConfBandPlanFx MUST also be set."
DEFVAL { bandPlan997 }
::= { vdslLineConfProfileEntry 31 }
vdslLineConfBandPlanFx OBJECT-TYPE
SYNTAX Unsigned32 (3750..12000)
UNITS "kHz"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The frequency limit between bands D2 and U2 when
vdslLineConfBandPlan is set to bandPlanFx(3)."
DEFVAL { 3750 }
::= { vdslLineConfProfileEntry 32 }
vdslLineConfBandOptUsage OBJECT-TYPE
SYNTAX INTEGER
{
unused(1),
upstream(2),
downstream(3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Defines the VDSL link use of the optional frequency
range [25kHz - 138kHz] (Opt).
unused(1) indicates Opt is unused
upstream(2) indicates Opt usage is for upstream
Expires December 12, 2003 [Page 49]
INTERNET-DRAFT VDSL-LINE MIB June 2003
downstream(3) indicates Opt usage is for downstream."
REFERENCE "ITU-T G.993.1, section 6.1"
DEFVAL { unused }
::= { vdslLineConfProfileEntry 33 }
vdslLineConfUpPsdTemplate OBJECT-TYPE
SYNTAX INTEGER
{
templateMask1(1),
templateMask2(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The upstream PSD template to be used for the line.
Here, templateMask1(1) refers to a notched mask that
limits the transmitted PSD within the internationally
standardized HAM (Handheld Amateur Radio) radio bands,
while templateMask2(2) refers to an unnotched mask.
The masks themselves depend upon the applicable
standard being used (vdslLineConfApplicableStandard)."
REFERENCE "DSL TR-057"
DEFVAL { templateMask1 }
::= { vdslLineConfProfileEntry 34 }
vdslLineConfDownPsdTemplate OBJECT-TYPE
SYNTAX INTEGER
{
templateMask1(1),
templateMask2(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The downstream PSD template to be used for the line.
Here, templateMask1(1) refers to a notched mask that
limits the transmitted PSD within the internationally
standardized HAM (Handheld Amateur Radio) radio bands,
while templateMask2(2) refers to an unnotched mask.
The masks themselves depend upon the applicable
standard being used (vdslLineConfApplicableStandard)."
REFERENCE "DSL TR-057"
DEFVAL { templateMask1 }
::= { vdslLineConfProfileEntry 35 }
vdslLineConfHamBandMask OBJECT-TYPE
SYNTAX BITS
{
customNotch1(0), -- custom (region-specific) notch
customNotch2(1), -- custom (region-specific) notch
Expires December 12, 2003 [Page 50]
INTERNET-DRAFT VDSL-LINE MIB June 2003
amateurBand30m(2), -- amateur radio band notch
amateurBand40m(3), -- amateur radio band notch
amateurBand80m(4), -- amateur radio band notch
amateurBand160m(5) -- amateur radio band notch
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The transmit power spectral density mask code, used
to avoid interference with HAM (Handheld Amateur Radio)
radio bands by introducing power control (notching) in one
or more of these bands.
Amateur radio band notching is defined in the VDSL
spectrum as follows:
Band Start Frequency Stop Frequency
---- ------------------ --------------------------------
30m 1810 kHz 2000 kHz
40m 3500 kHz 3800 kHz (ETSI); 4000 kHz (ANSI)
80m 7000 kHz 7100 kHz (ETSI); 7300 kHz (ANSI)
160m 10100 kHz 10150 kHz
Notching for each standard band can be enabled or disabled
via the bit mask.
Two custom notches may be specified. If either of these
are enabled via the bit mask, then the following objects
MUST be specified:
If customNotch1 is enabled, then both
vdslLineConfCustomNotch1Start
vdslLineConfCustomNotch1Stop
MUST be specified.
If customNotch2 is enabled, then both
vdslLineConfCustomNotch2Start
vdslLineConfCustomNotch2Stop
MUST be specified."
REFERENCE "DSLF TR-057, section 2.6"
DEFVAL { { } }
::= { vdslLineConfProfileEntry 36 }
vdslLineConfCustomNotch1Start OBJECT-TYPE
SYNTAX Unsigned32
UNITS "kHz"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the start frequency of custom HAM (Handheld
Amateur Radio) notch 1. vdslLineConfCustomNotch1Start MUST
be less than or equal to vdslLineConfCustomNotch1Stop."
Expires December 12, 2003 [Page 51]
INTERNET-DRAFT VDSL-LINE MIB June 2003
DEFVAL { 0 }
::= { vdslLineConfProfileEntry 37 }
vdslLineConfCustomNotch1Stop OBJECT-TYPE
SYNTAX Unsigned32
UNITS "kHz"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the stop frequency of custom HAM (Handheld
Amateur Radio) notch 1. vdslLineConfCustomNotch1Stop MUST
be greater than or equal to vdslLineConfCustomNotch1Start."
DEFVAL { 0 }
::= { vdslLineConfProfileEntry 38 }
vdslLineConfCustomNotch2Start OBJECT-TYPE
SYNTAX Unsigned32
UNITS "kHz"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the start frequency of custom HAM (Handheld
Amateur Radio) notch 2. vdslLineConfCustomNotch2Start MUST
be less than or equal to vdslLineConfCustomNotch2Stop."
DEFVAL { 0 }
::= { vdslLineConfProfileEntry 39 }
vdslLineConfCustomNotch2Stop OBJECT-TYPE
SYNTAX Unsigned32
UNITS "kHz"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the stop frequency of custom HAM (Handheld
Amateur Radio) notch 2. vdslLineConfCustomNotch2Stop MUST
be greater than or equal to vdslLineConfCustomNotch2Stop."
DEFVAL { 0 }
::= { vdslLineConfProfileEntry 40 }
vdslLineConfDownTargetSlowBurst OBJECT-TYPE
SYNTAX Unsigned32 (0..1275)
UNITS "microseconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the target level of impulse noise (burst)
protection for an interleaved (slow) channel."
REFERENCE "ITU-T G.997.1, section 7.3.2.3"
DEFVAL { 0 }
::= { vdslLineConfProfileEntry 41 }
vdslLineConfUpTargetSlowBurst OBJECT-TYPE
Expires December 12, 2003 [Page 52]
INTERNET-DRAFT VDSL-LINE MIB June 2003
SYNTAX Unsigned32 (0..1275)
UNITS "microseconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the target level of impulse noise (burst)
protection for an interleaved (slow) channel."
REFERENCE "ITU-T G.997.1, section 7.3.2.3"
DEFVAL { 0 }
::= { vdslLineConfProfileEntry 42 }
vdslLineConfDownMaxFastFec OBJECT-TYPE
SYNTAX Unsigned32 (0..50)
UNITS "%"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This parameter provisions the maximum level of Forward
Error Correction (FEC) redundancy related overhead to
be maintained for a fast channel."
DEFVAL { 0 }
::= { vdslLineConfProfileEntry 43 }
vdslLineConfUpMaxFastFec OBJECT-TYPE
SYNTAX Unsigned32 (0..50)
UNITS "%"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This parameter provisions the maximum level of Forward
Error Correction (FEC) redundancy related overhead to
be maintained for a fast channel."
DEFVAL { 0 }
::= { vdslLineConfProfileEntry 44 }
vdslLineConfLineType OBJECT-TYPE
SYNTAX INTEGER
{
noChannel(1), -- no channels exist
fastOnly(2), -- only fast channel exists
interleavedOnly(3), -- only interleaved channel exists
fastOrInterleaved(4), -- either fast or interleaved channel
-- exist, but only one at a time
fastAndInterleaved(5) -- both fast and interleaved channels
-- exist
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This parameter provisions the VDSL physical entity at
start-up by defining whether and how the line will be
channelized, i.e. which channel type(s) are supported.
Expires December 12, 2003 [Page 53]
INTERNET-DRAFT VDSL-LINE MIB June 2003
If the line is to be channelized, the value will be other
than noChannel(1).
This configuration can be activated only during start-up.
Afterwards, the value of vdslLineType coincides with the
value of vdslLineConfLineType. Depending on this vlaue,
the corresponding entries in the ifTable for the
interleaved and the fast channels are enabled or disabled
according to the value of their ifOperStatus.
Defined values are:
noChannel(1) -- no channels exist
fastOnly(2) -- only the fast channel exists
interleavedOnly(3) -- only the interleaved channel exists
fastOrInterleaved(4) -- either the fast or the interleaved
-- channel exists, but only one at a
-- time
fastAndInterleaved(5) -- both fast and interleaved channels
-- exist
Note that 'slow' and 'interleaved' refer to the same
channel."
REFERENCE "T1E1.4/2000-009R3, Part 1, common spec"
DEFVAL { noChannel }
::= { vdslLineConfProfileEntry 45 }
vdslLineConfProfRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is used to create a new row or modify or
delete an existing row in this table.
A profile activated by setting this object to 'active'.
When 'active' is set, the system will validate the profile.
Before a profile can be deleted or taken out of
service, (by setting this object to 'destroy' or
'outOfService') it must be first unreferenced
from all associated lines."
::= { vdslLineConfProfileEntry 46 }
--
-- Alarm configuration profile table
--
vdslLineAlarmConfProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF VdslLineAlarmConfProfileEntry
MAX-ACCESS not-accessible
STATUS current
Expires December 12, 2003 [Page 54]
INTERNET-DRAFT VDSL-LINE MIB June 2003
DESCRIPTION
"This table contains information on the VDSL line alarm
configuration. One entry in this table reflects a profile
defined by a manager which can be used to configure the
VDSL line alarm thresholds."
::= { vdslMibObjects 20 }
vdslLineAlarmConfProfileEntry OBJECT-TYPE
SYNTAX VdslLineAlarmConfProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry consists of a list of parameters that
represents the configuration of a VDSL line alarm
profile.
A default profile with an index of 'DEFVAL', will
always exist and its parameters will be set to vendor
specific values, unless otherwise specified in this
document."
INDEX { vdslLineAlarmConfProfileName }
::= { vdslLineAlarmConfProfileTable 1 }
VdslLineAlarmConfProfileEntry ::=
SEQUENCE
{
vdslLineAlarmConfProfileName SnmpAdminString,
vdslThresh15MinLofs HCPerfIntervalThreshold,
vdslThresh15MinLoss HCPerfIntervalThreshold,
vdslThresh15MinLprs HCPerfIntervalThreshold,
vdslThresh15MinLols HCPerfIntervalThreshold,
vdslThresh15MinESs HCPerfIntervalThreshold,
vdslThresh15MinSESs HCPerfIntervalThreshold,
vdslThresh15MinUASs HCPerfIntervalThreshold,
vdslInitFailureNotifyEnable TruthValue,
vdslLineAlarmConfProfRowStatus RowStatus
}
vdslLineAlarmConfProfileName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (1..32))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The name for this profile as specified by an
adminstrator."
::= { vdslLineAlarmConfProfileEntry 1 }
vdslThresh15MinLofs OBJECT-TYPE
SYNTAX HCPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
Expires December 12, 2003 [Page 55]
INTERNET-DRAFT VDSL-LINE MIB June 2003
DESCRIPTION
"This object configures the threshold for the number of
loss of frame seconds (lofs) within any given 15-minute
performance data collection interval. If the value of
loss of frame seconds in a particular 15-minute collection
interval reaches/exceeds this value, a
vdslPerfLofsThreshNotification notification will be
generated. No more than one notification will be sent
per interval."
DEFVAL { 0 }
::= { vdslLineAlarmConfProfileEntry 2 }
vdslThresh15MinLoss OBJECT-TYPE
SYNTAX HCPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the threshold for the number of
loss of signal seconds (loss) within any given 15-minute
performance data collection interval. If the value of
loss of signal seconds in a particular 15-minute
collection interval reaches/exceeds this value, a
vdslPerfLossThreshNotification notification will be
generated. One notification will be sent per interval
per endpoint."
DEFVAL { 0 }
::= { vdslLineAlarmConfProfileEntry 3 }
vdslThresh15MinLprs OBJECT-TYPE
SYNTAX HCPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the threshold for the number of
loss of power seconds (lprs) within any given 15-minute
performance data collection interval. If the value of
loss of power seconds in a particular 15-minute collection
interval reaches/exceeds this value, a
vdslPerfLprsThreshNotification notification will be
generated. No more than one notification will be sent
per interval."
DEFVAL { 0 }
::= { vdslLineAlarmConfProfileEntry 4 }
vdslThresh15MinLols OBJECT-TYPE
SYNTAX HCPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
Expires December 12, 2003 [Page 56]
INTERNET-DRAFT VDSL-LINE MIB June 2003
"This object configures the threshold for the number of
loss of link seconds (lols) within any given 15-minute
performance data collection interval. If the value of
loss of power seconds in a particular 15-minute collection
interval reaches/exceeds this value, a
vdslPerfLolsThreshNotification notification will be
generated. No more than one notification will be sent
per interval."
DEFVAL { 0 }
::= { vdslLineAlarmConfProfileEntry 5 }
vdslThresh15MinESs OBJECT-TYPE
SYNTAX HCPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the threshold for the number of
errored seconds (ESs) within any given 15-minute
performance data collection interval. If the value of
errored seconds in a particular 15-minute collection
interval reaches/exceeds this value, a
vdslPerfESsThreshNotification notification will be
generated. No more than one notification will be sent
per interval."
DEFVAL { 0 }
::= { vdslLineAlarmConfProfileEntry 6 }
vdslThresh15MinSESs OBJECT-TYPE
SYNTAX HCPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the threshold for the number of
severely errored seconds (SESs) within any given 15-minute
performance data collection interval. If the value of
severely errored seconds in a particular 15-minute
collection interval reaches/exceeds this value, a
vdslPerfSESsThreshNotification notification will be
generated. No more than one notification will be sent
per interval."
DEFVAL { 0 }
::= { vdslLineAlarmConfProfileEntry 7 }
vdslThresh15MinUASs OBJECT-TYPE
SYNTAX HCPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the threshold for the number of
Expires December 12, 2003 [Page 57]
INTERNET-DRAFT VDSL-LINE MIB June 2003
unavailable seconds (UASs) within any given 15-minute
performance data collection interval. If the value of
unavailable seconds in a particular 15-minute collection
interval reaches/exceeds this value, a
vdslPerfUASsThreshNotification notification will be
generated. No more than one notification will be sent
per interval."
DEFVAL { 0 }
::= { vdslLineAlarmConfProfileEntry 8 }
vdslInitFailureNotifyEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies if a vdslInitFailureNotification
notification will be generated if an initialization
failure occurs."
DEFVAL { false }
::= { vdslLineAlarmConfProfileEntry 9 }
vdslLineAlarmConfProfRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is used to create a new row or modify or
delete an existing row in this table.
A profile activated by setting this object to 'active'.
When 'active' is set, the system will validate the profile.
Before a profile can be deleted or taken out of service,
(by setting this object to 'destroy' or 'outOfService') it
must be first unreferenced from all associated lines."
::= { vdslLineAlarmConfProfileEntry 10 }
-- Notification definitions
vdslNotifications OBJECT IDENTIFIER ::= { vdslLineMib 0 }
vdslPerfLofsThreshNotification NOTIFICATION-TYPE
OBJECTS {
vdslPerfCurr15MinLofs
}
STATUS current
DESCRIPTION
"Loss of Framing 15-minute interval threshold
(vdslThresh15MinLofs) reached."
::= { vdslNotifications 1 }
vdslPerfLossThreshNotification NOTIFICATION-TYPE
Expires December 12, 2003 [Page 58]
INTERNET-DRAFT VDSL-LINE MIB June 2003
OBJECTS {
vdslPerfCurr15MinLoss
}
STATUS current
DESCRIPTION
"Loss of Signal 15-minute interval threshold
(vdslThresh15MinLoss) reached."
::= { vdslNotifications 2 }
vdslPerfLprsThreshNotification NOTIFICATION-TYPE
OBJECTS {
vdslPerfCurr15MinLprs
}
STATUS current
DESCRIPTION
"Loss of Power 15-minute interval threshold
(vdslThresh15MinLprs) reached."
::= { vdslNotifications 3 }
vdslPerfLolsThreshNotification NOTIFICATION-TYPE
OBJECTS {
vdslPerfCurr15MinLols
}
STATUS current
DESCRIPTION
"Loss of Link 15-minute interval threshold
(vdslThresh15MinLols) reached."
::= { vdslNotifications 4 }
vdslPerfESsThreshNotification NOTIFICATION-TYPE
OBJECTS {
vdslPerfCurr15MinESs
}
STATUS current
DESCRIPTION
"Errored Seconds 15-minute interval threshold
(vdslThresh15MinESs) reached."
::= { vdslNotifications 5 }
vdslPerfSESsThreshNotification NOTIFICATION-TYPE
OBJECTS {
vdslPerfCurr15MinSESs
}
STATUS current
DESCRIPTION
"Severely Errored Seconds 15-minute interval threshold
(vdslThresh15MinSESs) reached."
::= { vdslNotifications 6 }
vdslPerfUASsThreshNotification NOTIFICATION-TYPE
OBJECTS {
vdslPerfCurr15MinUASs
Expires December 12, 2003 [Page 59]
INTERNET-DRAFT VDSL-LINE MIB June 2003
}
STATUS current
DESCRIPTION
"Unavailable Seconds 15-minute interval threshold
(vdslThresh15MinUASs) reached."
::= { vdslNotifications 7 }
vdslDownMaxSnrMgnNotification NOTIFICATION-TYPE
OBJECTS {
vdslCurrSnrMgn
}
STATUS current
DESCRIPTION
"The downstream Signal to Noise Margin exceeded
vdslLineConfDownMaxSnrMgn. The object
vdslCurrSnrMgn will contain the Signal to Noise
margin as measured by the VTU-R."
::= { vdslNotifications 8 }
vdslDownMinSnrMgnNotification NOTIFICATION-TYPE
OBJECTS {
vdslCurrSnrMgn
}
STATUS current
DESCRIPTION
"The downstream Signal to Noise Margin fell below
vdslLineConfDownMinSnrMgn. The object
vdslCurrSnrMgn will contain the Signal to Noise
margin as measured by the VTU-R."
::= { vdslNotifications 9 }
vdslUpMaxSnrMgnNotification NOTIFICATION-TYPE
OBJECTS {
vdslCurrSnrMgn
}
STATUS current
DESCRIPTION
"The upstream Signal to Noise Margin exceeded
vdslLineConfUpMaxSnrMgn. The object
vdslCurrSnrMgn will contain the Signal to Noise
margin as measured by the VTU-C."
::= { vdslNotifications 10 }
vdslUpMinSnrMgnNotification NOTIFICATION-TYPE
OBJECTS {
vdslCurrSnrMgn
}
STATUS current
DESCRIPTION
"The upstream Signal to Noise Margin fell below
vdslLineConfUpMinSnrMgn. The object
vdslCurrSnrMgn will contain the Signal to Noise
Expires December 12, 2003 [Page 60]
INTERNET-DRAFT VDSL-LINE MIB June 2003
margin as measured by the VTU-C."
::= { vdslNotifications 11 }
vdslInitFailureNotification NOTIFICATION-TYPE
OBJECTS {
vdslCurrStatus
}
STATUS current
DESCRIPTION
"Vtu initialization failed. See vdslCurrStatus for
potential reasons."
::= { vdslNotifications 12 }
-- conformance information
vdslConformance OBJECT IDENTIFIER ::= { vdslLineMib 3 }
vdslGroups OBJECT IDENTIFIER ::= { vdslConformance 1 }
vdslCompliances OBJECT IDENTIFIER ::= { vdslConformance 2 }
vdslLineMibCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for SNMP entities which
manage VDSL interfaces."
MODULE -- this module
MANDATORY-GROUPS
{
vdslGroup,
vdslNotificationGroup
}
::= { vdslCompliances 1 }
-- units of conformance
vdslGroup OBJECT-GROUP
OBJECTS
{
vdslLineCoding,
vdslLineType,
vdslLineConfProfile,
vdslLineAlarmConfProfile,
vdslInvSerialNumber,
vdslInvVendorID,
vdslInvVersionNumber,
vdslCurrSnrMgn,
vdslCurrAtn,
vdslCurrStatus,
vdslCurrOutputPwr,
vdslCurrAttainableRate,
vdslCurrLineRate,
vdslChanInterleaveDelay,
Expires December 12, 2003 [Page 61]
INTERNET-DRAFT VDSL-LINE MIB June 2003
vdslChanCrcBlockLength,
vdslChanCurrTxRate,
vdslChanCurrTxSlowBurstProtect,
vdslChanCurrTxFastFec,
vdslPerfValidIntervals,
vdslPerfInvalidIntervals,
vdslPerfLofs,
vdslPerfLoss,
vdslPerfLprs,
vdslPerfLols,
vdslPerfESs,
vdslPerfSESs,
vdslPerfUASs,
vdslPerfInits,
vdslPerfCurr15MinTimeElapsed,
vdslPerfCurr15MinLofs,
vdslPerfCurr15MinLoss,
vdslPerfCurr15MinLprs,
vdslPerfCurr15MinLols,
vdslPerfCurr15MinESs,
vdslPerfCurr15MinSESs,
vdslPerfCurr15MinUASs,
vdslPerfCurr15MinInits,
vdslPerf1DayValidIntervals,
vdslPerf1DayInvalidIntervals,
vdslPerfCurr1DayTimeElapsed,
vdslPerfCurr1DayLofs,
vdslPerfCurr1DayLoss,
vdslPerfCurr1DayLprs,
vdslPerfCurr1DayLols,
vdslPerfCurr1DayESs,
vdslPerfCurr1DaySESs,
vdslPerfCurr1DayUASs,
vdslPerfCurr1DayInits,
vdslIntervalLofs,
vdslIntervalLoss,
vdslIntervalLprs,
vdslIntervalLols,
vdslIntervalESs,
vdslIntervalSESs,
vdslIntervalUASs,
vdslIntervalInits,
vdsl1DayIntervalMoniSecs,
vdsl1DayIntervalLofs,
vdsl1DayIntervalLoss,
vdsl1DayIntervalLprs,
vdsl1DayIntervalLols,
vdsl1DayIntervalESs,
vdsl1DayIntervalSESs,
vdsl1DayIntervalUASs,
vdsl1DayIntervalInits,
vdslChanValidIntervals,
Expires December 12, 2003 [Page 62]
INTERNET-DRAFT VDSL-LINE MIB June 2003
vdslChanInvalidIntervals,
vdslChanFixedOctets,
vdslChanBadBlks,
vdslChanCurr15MinTimeElapsed,
vdslChanCurr15MinFixedOctets,
vdslChanCurr15MinBadBlks,
vdslChan1DayValidIntervals,
vdslChan1DayInvalidIntervals,
vdslChanCurr1DayTimeElapsed,
vdslChanCurr1DayFixedOctets,
vdslChanCurr1DayBadBlks,
vdslChanIntervalFixedOctets,
vdslChanIntervalBadBlks,
vdslChan1DayIntervalMoniSecs,
vdslChan1DayIntervalFixedOctets,
vdslChan1DayIntervalBadBlks,
vdslLineConfDownRateMode,
vdslLineConfUpRateMode,
vdslLineConfDownMaxPwr,
vdslLineConfUpMaxPwr,
vdslLineConfDownMaxSnrMgn,
vdslLineConfDownMinSnrMgn,
vdslLineConfDownTargetSnrMgn,
vdslLineConfUpMaxSnrMgn,
vdslLineConfUpMinSnrMgn,
vdslLineConfUpTargetSnrMgn,
vdslLineConfDownFastMaxDataRate,
vdslLineConfDownFastMinDataRate,
vdslLineConfDownSlowMaxDataRate,
vdslLineConfDownSlowMinDataRate,
vdslLineConfUpFastMaxDataRate,
vdslLineConfUpFastMinDataRate,
vdslLineConfUpSlowMaxDataRate,
vdslLineConfUpSlowMinDataRate,
vdslLineConfDownRateRatio,
vdslLineConfUpRateRatio,
vdslLineConfDownMaxInterDelay,
vdslLineConfUpMaxInterDelay,
vdslLineConfDownPboControl,
vdslLineConfUpPboControl,
vdslLineConfDownPboLevel,
vdslLineConfUpPboLevel,
vdslLineConfDeploymentScenario,
vdslLineConfAdslPresence,
vdslLineConfApplicableStandard,
vdslLineConfBandPlan,
vdslLineConfBandPlanFx,
vdslLineConfBandOptUsage,
vdslLineConfUpPsdTemplate,
vdslLineConfDownPsdTemplate,
vdslLineConfHamBandMask,
vdslLineConfCustomNotch1Start,
Expires December 12, 2003 [Page 63]
INTERNET-DRAFT VDSL-LINE MIB June 2003
vdslLineConfCustomNotch1Stop,
vdslLineConfCustomNotch2Start,
vdslLineConfCustomNotch2Stop,
vdslLineConfDownTargetSlowBurst,
vdslLineConfUpTargetSlowBurst,
vdslLineConfDownMaxFastFec,
vdslLineConfUpMaxFastFec,
vdslLineConfLineType,
vdslLineConfProfRowStatus,
vdslThresh15MinLofs,
vdslThresh15MinLoss,
vdslThresh15MinLprs,
vdslThresh15MinLols,
vdslThresh15MinESs,
vdslThresh15MinSESs,
vdslThresh15MinUASs,
vdslInitFailureNotifyEnable,
vdslLineAlarmConfProfRowStatus
}
STATUS current
DESCRIPTION
"A collection of objects providing information about
a VDSL Line."
::= { vdslGroups 1 }
vdslNotificationGroup NOTIFICATION-GROUP
NOTIFICATIONS
{
vdslPerfLofsThreshNotification,
vdslPerfLossThreshNotification,
vdslPerfLprsThreshNotification,
vdslPerfLolsThreshNotification,
vdslPerfESsThreshNotification,
vdslPerfSESsThreshNotification,
vdslPerfUASsThreshNotification,
vdslDownMaxSnrMgnNotification,
vdslDownMinSnrMgnNotification,
vdslUpMaxSnrMgnNotification,
vdslUpMinSnrMgnNotification,
vdslInitFailureNotification
}
STATUS current
DESCRIPTION
"This group supports notifications of significant
conditions associated with VDSL Lines."
::= { vdslGroups 2 }
END
5. Intellectual Property Notice
The IETF takes no position regarding the validity or scope of any
Expires December 12, 2003 [Page 64]
INTERNET-DRAFT VDSL-LINE MIB June 2003
intellectual property or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; neither does it represent that it
has made any effort to identify any such rights. Information on the
IETF's procedures with respect to rights in standards-track and
standards-related documentation can be found in BCP-11. Copies of
claims of rights made available for publication and any assurances
of licenses to be made available, or the result of an attempt made
to obtain a general license or permission for the use of such
proprietary rights by implementors or users of this specification
can be obtained from the IETF Secretariat.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights which may cover technology that may be required to practice
this standard. Please address the information to the IETF Executive
Director.
6. Normative References
[DSLFTR057] DSL Forum TR-057, "VDSL Network Element Management",
February 2003.
[ETSI2701] ETSI TS 101 270-1 V1.2.1 "Transmission and Multiplexing
(TM); Access transmission systems on metallic access
cables; Very high speed Digital Subscriber Line (VDSL);
Part 1: Functional requirements", October 1999.
[ETSI2702] ETSI TS 101 270-2 V1.1.1 "Transmission and Multiplexing
(TM); Access transmission systems on metallic access
cables; Very high speed Digital Subscriber Line (VDSL);
Part 1: Transceiver specification", February 2001.
[ITU9931] ITU-T G.993.1 "Very-high-speed digital subscriber line
foundation", November 2001.
[ITU9971] ITU-T G.997.1 "Physical layer management for Digital
Subscriber Line (DSL) Transceivers", July 1999.
[RFC2493] Tesink, K., "Textual Conventions for MIB Modules Using
Performance History Based on 15 Minute Intervals", RFC
2493, January 1999.
[RFC2578] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
Rose, M. and S. Waldbusser, "Structure of Management
Information Version 2 (SMIv2)", STD 58, RFC 2578, April
1999.
[RFC2579] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
Rose, M. and S. Waldbusser, "Textual Conventions for
SMIv2", STD 58, RFC 2579, April 1999.
Expires December 12, 2003 [Page 65]
INTERNET-DRAFT VDSL-LINE MIB June 2003
[RFC2580] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
Rose, M. and S. Waldbusser, "Conformance Statements for
SMIv2", STD 58, RFC 2580, April 1999.
[RFC2863] McCloghrie, K. and F. Kastenholz, "The Interfaces Group
MIB", RFC 2863, June 2000.
[RFC3418] Presuhn, R., "Management Information Base (MIB) for the
Simple Network Management Protocol (SNMP)", STD 62, RFC
3418, December 2002.
[RFCXXXX] Ray, B. and R. Abbi, "High Capacity Textual Conventions
for MIB Modules Using Performance History Based on
15 Minute Intervals", RFC XXXX, YYYY 2003.
--- RFC Ed: please replace XXXX with the RFC number assigned to the
--- accompanying HC-TC MIB and YYYY with the appropriate month.
[T1E1311] ANSI T1E1.4/2001-311, "Very-high-bit-rate Digital
Subscriber Line (VDSL) Metallic Interface, Part 1:
Functional Requirements and Common Specification",
February 2001.
[T1E1011] ANSI T1E1.4/2001-011R3, "VDSL Metallic Interface, Part 2:
Technical Specification for a Single-Carrier Modulation
(SCM) Transceiver", November 2001.
[T1E1013] ANSI T1E1.4/2001-013R4, "VDSL Metallic Interface, Part 3:
Technical Specification for a Multi-Carrier Modulation
(MCM) Transceiver", November 2000.
7. Informative References
[RFC2575] Wijnen, B., Presuhn, R. and K. McCloghrie, "View-based
Access Control Model (VACM) for the Simple Network
Management Protocol (SNMP)", RFC 2575, April 1999.
[RFC3410] Case, J., Mundy, R., Partain, D. and B. Stewart,
"Introduction and Applicability Statements for Internet-
Standard Management Framework", RFC 3410, December 2002.
8. Security Considerations
There are a number of management objects defined in this MIB that
have a MAX-ACCESS clause of read-write and/or read-create. Such
objects may be considered sensitive or vulnerable in some network
environments. The support for SET operations in a non-secure
environment without proper protection can have a negative effect on
network operations.
VDSL layer connectivity from the Vtur will permit the subscriber
to manipulate both the VDSL link directly and the VDSL embedded
Expires December 12, 2003 [Page 66]
INTERNET-DRAFT VDSL-LINE MIB June 2003
operations channel (EOC) for their own loop. For example, unchecked
or unfiltered fluctuations initiated by the subscriber could
generate sufficient notifications to potentially overwhelm either
the management interface to the network or the element manager.
For this reason, there are a number of managed objects in this MIB
that may contain sensitive information. These are:
vdslThresh15MinLofs
vdslThresh15MinLoss
vdslThresh15MinLprs
vdslThresh15MinLols
vdslThresh15MinESs
vdslThresh15MinSESs
vdslThresh15MinUASs
It is thus important to control even GET access to these objects and
possibly to even encrypt the values of these objects when sending
them over the network via SNMP. Not all versions of SNMP provide
features for such a secure environment.
Further, notifications generated by agents implementing this MIB
will contain the above threshold information.
SNMP versions prior to SNMPv3 did not include adequate security.
Even if the network itself is secure (for example by using IPSec),
even then, there is no control as to who on the secure network is
allowed to access and GET/SET (read/change/create/delete) objects
which utilize the textual conventions defined in this MIB module.
It is RECOMMENDED that implementers consider the security features
as provided by the SNMPv3 framework (see [RFC3410], section 8),
including full support for the SNMPv3 cryptographic mechanisms (for
authentication and privacy).
Further, deployment of SNMP versions prior to SNMPv3 is NOT
RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to
enable cryptographic security. It is then a customer/operator
responsibility to ensure that the SNMP entity giving access to an
instance of a MIB module which utilizes the textual conventions
defined in this MIB module is properly configured to give access to
the objects only to those principals (users) that have legitimate
rights to indeed GET or SET (change/create/delete) them.
9. Acknowledgments
Greg Bathrick (Nokia)
Umberto Bonollo (NEC)
Andrew Cheers (NEC)
Expires December 12, 2003 [Page 67]
INTERNET-DRAFT VDSL-LINE MIB June 2003
Felix Flemisch (Siemens)
David Horton (CiTR)
Travis Levin (Paradyne)
Moti Morgenstern (Inovia)
Randy Presuhn (BMC)
Say Sabit (NLC)
Bert Wijnen (Lucent)
10. Authors' Addresses
Bob Ray
PESA Switching Systems, Inc.
330-A Wynn Drive
Huntsville, AL 35805
USA
Phone: +1 256 726 9200 ext. 142
Fax: +1 256 726 9271
EMail: rray@pesa.com
Rajesh Abbi
Alcatel USA
2912 Wake Forest Road
Raleigh, NC 27609-7860
USA
Phone: +1 919 850 6194
EMail: Rajesh.Abbi@alcatel.com
11. Full Copyright Statement
Copyright (C) The Internet Society (2003). All Rights Reserved.
This document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain it
or assist in its implementation may be prepared, copied, published
and distributed, in whole or in part, without restriction of any
kind, provided that the above copyright notice and this paragraph
are included on all such copies and derivative works. However, this
document itself may not be modified in any way, such as by removing
the copyright notice or references to the Internet Society or other
Internet organizations, except as needed for the purpose of
developing Internet standards in which case the procedures for
copyrights defined in the Internet Standards process must be
followed, or as required to translate it into languages other than
English.
Expires December 12, 2003 [Page 68]
INTERNET-DRAFT VDSL-LINE MIB June 2003
The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an
"AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Expires December 12, 2003 [Page 69]