Network Working Group D. Thaler
INTERNET-DRAFT Microsoft
Expires July 2004 January 2004
IP Tunnel MIB
<draft-ietf-ipv6-inet-tunnel-mib-00.txt>
Status of this Memo
This document is an Internet-Draft and is in full conformance with
all provisions of Section 10 of RFC2026.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six
months and may be updated, replaced, or obsoleted by other
documents at any time. It is inappropriate to use Internet-
Drafts as reference material or to cite them other than as "work
in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
Copyright Notice
Copyright (C) The Internet Society (2004). All Rights Reserved.
Abstract
Expires July 2004 [Page 1]
Draft Inet Tunnel MIB January 2004
This memo defines a Management Information Base (MIB) for use with
network management protocols in the Internet community. In
particular, it describes managed objects used for managing tunnels
of any type over IPv4 and IPv6 networks. Extension MIBs may be
designed for managing protocol-specific objects. Likewise,
extension MIBs may be designed for managing security-specific
objects. This MIB does not support tunnels over non-IP networks.
Management of such tunnels may be supported by other MIBs.
1. Introduction
Over the past several years, there have been a number of
"tunneling" protocols specified by the IETF (see [RFC1241] for an
early discussion of the model and examples). This document
describes a Management Information Base (MIB) used for managing
tunnels of any type over IPv4 networks, including GRE
[RFC1701,RFC1702], IP-in-IP [RFC2003], Minimal Encapsulation
[RFC2004], L2TP [RFC2661], PPTP [RFC2637], L2F [RFC2341], UDP
(e.g., [RFC1234]), ATMP [RFC2107], and IPv6-in-IPv4 [RFC2893]
tunnels.
Extension MIBs may be designed for managing protocol-specific
objects. Likewise, extension MIBs may be designed for managing
security-specific objects (e.g., IPSEC [RFC2401]), and traffic
conditioner [RFC2474] objects. Finally, this MIB does not support
tunnels over non- IPv4 networks (including IPv6 networks).
Management of such tunnels may be supported by other MIBs.
2. The Internet-Standard Management Framework
For a detailed overview of the documents that describe the
current Internet-Standard Management Framework, please refer to
section 7 of RFC 3410 [RFC3410].
Managed objects are accessed via a virtual information store,
termed the Management Information Base or MIB. MIB objects are
generally accessed through the Simple Network Management
Protocol (SNMP). Objects in the MIB are defined using the
mechanisms defined in the Structure of Management Information
(SMI). This memo specifies a MIB module that is compliant to
the SMIv2, which is described in STD 58, RFC 2578 [RFC2578],
STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580 [RFC2580].
Expires July 2004 [Page 2]
Draft Inet Tunnel MIB January 2004
3. Overview
This MIB module contains two current tables and one deprecated
table. The current tables are:
o the Tunnel Interface Table, containing information on the
tunnels known to a router; and
o the Tunnel Inet Config Table, which can be used for dynamic
creation of tunnels, and also provides a mapping from
endpoint addresses to the current interface index value.
The version of this MIB that appeared in RFC 2667 contained
the Tunnel Config Table, which mapped IPv4 endpoint addresses
to interface indexes. It is now deprecated in favor of the
Tunnel Inet Config Table.
3.1. Relationship to the Interfaces MIB
This section clarifies the relationship of this MIB to the
Interfaces MIB [RFC2863]. Several areas of correlation are
addressed in the following subsections. The implementor is
referred to the Interfaces MIB document in order to understand the
general intent of these areas.
3.1.1. Layering Model
Each logical interface (physical or virtual) has an ifEntry in the
Interfaces MIB [RFC2863]. Tunnels are handled by creating a
logical interface (ifEntry) for each tunnel. These are then
correlated, using the ifStack table of the Interfaces MIB, to
those interfaces on which the local IPv4 addresses of the tunnels
are configured. The basic model, therefore, looks something like
this (for example):
| | | | | |
+--+ +---+ +--+ +---+ | |
|IP-in-IP| | GRE | | |
| tunnel | | tunnel | | |
+--+ +---+ +--+ +---+ | |
| | | | | | <== attachment to underlying
+--+ +---------+ +----------+ +--+ interfaces, to be provided
| Physical interface | by ifStack table
Expires July 2004 [Page 3]
Draft Inet Tunnel MIB January 2004
+--------------------------------+
3.1.2. ifRcvAddressTable
The ifRcvAddressTable usage can be defined in the MIBs defining
the encapsulation below the network layer, and holds the local IP
addresses on which decapsulation will occur. For example, if IP-
in-IP encapsulation is being used, the ifRcvAddressTable can be
defined by IP- in-IP. If it is not specified, the default is that
one entry will exist for the tunnel interface, where
ifRcvAddressAddress contains the local IP address used for
encapsulation/decapsulation (i.e., tunnelIfLocalInetAddress in the
Tunnel Interface Table).
3.1.3. ifEntry
IfEntries are defined in the MIBs defining the encapsulation below
the network layer. For example, if IP-in-IP encapsulation [20] is
being used, the ifEntry is defined by IP-in-IP.
The ifType of a tunnel should be set to "tunnel" (131). An entry
in the IP Tunnel MIB will exist for every ifEntry with this
ifType. An implementation of the IP Tunnel MIB may allow
ifEntries to be created via the tunnelConfigTable. Creating a
tunnel will also add an entry in the ifTable and in the
tunnelIfTable, and deleting a tunnel will likewise delete the
entry in the ifTable and the tunnelIfTable.
The use of two different tables in this MIB was an important
design decision. Traditionally, ifIndex values are chosen by
agents, and are permitted to change across restarts. Allowing row
creation directly in the Tunnel Interface Table, indexed by
ifIndex, would complicate row creation and/or cause
interoperability problems (if each agent had special restrictions
on ifIndex). Instead, a separate table is used which is indexed
only by objects over which the manager has control. Namely, these
are the addresses of the tunnel endpoints and the encapsulation
protocol. Finally, an additional manager- chosen ID is used in
the index to support protocols such as L2F which allow multiple
tunnels between the same endpoints.
Expires July 2004 [Page 4]
Draft Inet Tunnel MIB January 2004
3.1.4. ifEntry
IfEntries are defined in the MIBs defining the encapsulation below
the network layer. For example, if IP-in-IP encapsulation [20] is
being used, the ifEntry is defined by IP-in-IP.
The ifType of a tunnel should be set to "tunnel" (131). An entry
in the IP Tunnel MIB will exist for every ifEntry with this
ifType. An implementation of the IP Tunnel MIB may allow
ifEntries to be created via the tunnelConfigTable. Creating a
tunnel will also add an entry in the ifTable and in the
tunnelIfTable, and deleting a tunnel will likewise delete the
entry in the ifTable and the tunnelIfTable.
The use of two different tables in this MIB was an important
design decision. Traditionally, ifIndex values are chosen by
agents, and are permitted to change across restarts. Allowing row
creation directly in the Tunnel Interface Table, indexed by
ifIndex, would complicate row creation and/or cause
interoperability problems (if each agent had special restrictions
on ifIndex). Instead, a separate table is used which is indexed
only by objects over which the manager has control. Namely, these
are the addresses of the tunnel endpoints and the encapsulation
protocol. Finally, an additional manager- chosen ID is used in
the index to support protocols such as L2F which allow multiple
tunnels between the same endpoints.
4. Definitions
TUNNEL-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, transmission,
Integer32, IpAddress FROM SNMPv2-SMI
RowStatus, StorageType FROM SNMPv2-TC
MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF
InetAddressType, InetAddress FROM INET-ADDRESS-MIB
IPv6FlowLabelOrAny FROM IPV6-FLOW-LABEL-MIB
ifIndex, InterfaceIndexOrZero FROM IF-MIB
IANAtunnelType FROM IANA-TUNNELTYPE-MIB;
tunnelMIB MODULE-IDENTITY
LAST-UPDATED "200401191200Z" -- January 19, 2003
ORGANIZATION "IETF Interfaces MIB Working Group"
Expires July 2004 [Page 5]
Draft Inet Tunnel MIB January 2004
CONTACT-INFO
" Dave Thaler
Microsoft Corporation
One Microsoft Way
Redmond, WA 98052-6399
EMail: dthaler@microsoft.com"
DESCRIPTION
"The MIB module for management of IP Tunnels,
independent of the specific encapsulation scheme in
use.
Copyright (C) The Internet Society (date). This
version of this MIB module is part of RFC yyyy; see
the RFC itself for full legal notices."
-- RFC Ed.: replace yyyy with actual RFC number & remove this note
REVISION "199908241200Z" -- August 24, 1999
DESCRIPTION
"Initial version, published as RFC 2667."
REVISION "200401191200Z" -- January 19, 2003
DESCRIPTION
"Added support for IPv6. Published as RFC yyyy."
-- RFC Ed.: replace yyyy with actual RFC number & remove this note
::= { transmission 131 }
tunnelMIBObjects OBJECT IDENTIFIER ::= { tunnelMIB 1 }
tunnel OBJECT IDENTIFIER ::= { tunnelMIBObjects 1 }
-- the IP Tunnel MIB-Group
--
-- a collection of objects providing information about
-- IP Tunnels
tunnelIfTable OBJECT-TYPE
SYNTAX SEQUENCE OF TunnelIfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The (conceptual) table containing information on
configured tunnels."
::= { tunnel 1 }
tunnelIfEntry OBJECT-TYPE
SYNTAX TunnelIfEntry
MAX-ACCESS not-accessible
Expires July 2004 [Page 6]
Draft Inet Tunnel MIB January 2004
STATUS current
DESCRIPTION
"An entry (conceptual row) containing the information
on a particular configured tunnel."
INDEX { ifIndex }
::= { tunnelIfTable 1 }
TunnelIfEntry ::= SEQUENCE {
tunnelIfLocalAddress IpAddress, -- deprecated
tunnelIfRemoteAddress IpAddress, -- deprecated
tunnelIfEncapsMethod IANAtunnelType,
tunnelIfHopLimit Integer32,
tunnelIfSecurity INTEGER,
tunnelIfTOS Integer32,
tunnelIfFlowLabel IPv6FlowLabelOrAny,
tunnelIfAddressType InetAddressType,
tunnelIfLocalInetAddress InetAddress,
tunnelIfRemoteInetAddress InetAddress
}
tunnelIfLocalAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The address of the local endpoint of the tunnel
(i.e., the source address used in the outer IP
header), or 0.0.0.0 if unknown or if the tunnel is
over IPv6. This object is deprecated in favor of
tunnelIfLocalInetAddress."
::= { tunnelIfEntry 1 }
tunnelIfRemoteAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The address of the remote endpoint of the tunnel
(i.e., the destination address used in the outer IP
header), or 0.0.0.0 if unknown, or an IPv6 address, or
the tunnel is not a point-to-point link (e.g., if it
is a 6to4 tunnel). This object is deprecated in favor
of tunnelIfRemoteInetAddress."
::= { tunnelIfEntry 2 }
Expires July 2004 [Page 7]
Draft Inet Tunnel MIB January 2004
tunnelIfEncapsMethod OBJECT-TYPE
SYNTAX IANAtunnelType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The encapsulation method used by the tunnel."
::= { tunnelIfEntry 3 }
tunnelIfHopLimit OBJECT-TYPE
SYNTAX Integer32 (0..255)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The IPv4 TTL or IPv6 Hop Limit to use in the outer IP
header. A value of 0 indicates that the value is
copied from the payload's header."
::= { tunnelIfEntry 4 }
tunnelIfSecurity OBJECT-TYPE
SYNTAX INTEGER {
none(1), -- no security
ipsec(2), -- IPSEC security
other(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The method used by the tunnel to secure the outer IP
header. The value ipsec indicates that IPsec is used
between the tunnel endpoints for authentication or
encryption or both. More specific security-related
information may be available in a MIB for the security
protocol in use."
::= { tunnelIfEntry 5 }
tunnelIfTOS OBJECT-TYPE
SYNTAX Integer32 (-2..63)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The method used to set the high 6 bits of the IPv4
TOS or IPv6 Traffic Class in the outer IP header. A
value of -1 indicates that the bits are copied from
the payload's header. A value of -2 indicates that a
traffic conditioner is invoked and more information
Expires July 2004 [Page 8]
Draft Inet Tunnel MIB January 2004
may be available in a traffic conditioner MIB. A
value between 0 and 63 inclusive indicates that the
bit field is set to the indicated value."
::= { tunnelIfEntry 6 }
tunnelIfFlowLabel OBJECT-TYPE
SYNTAX IPv6FlowLabelOrAny
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The method used to set the IPv6 Flow Label value.
This object need not be present in rows where
tunnelIfAddressType indicates the tunnel is over IPv6.
A value of -1 indicates that a traffic conditioner is
invoked and more information may be available in a
traffic conditioner MIB. Any other value indicates
that the Flow Label field is set to the indicated
value."
::= { tunnelIfEntry 7 }
tunnelIfAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The type of address in the corresponding
tunnelIfLocalInetAddress and tunnelIfRemoteInetAddress
objects."
::= { tunnelIfEntry 8 }
tunnelIfLocalInetAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The address of the local endpoint of the tunnel
(i.e., the source address used in the outer IP
header). If the address is unknown, the value is
0.0.0.0 for IPv4 or :: for IPv6."
::= { tunnelIfEntry 9 }
tunnelIfRemoteInetAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-write
STATUS current
Expires July 2004 [Page 9]
Draft Inet Tunnel MIB January 2004
DESCRIPTION
"The address of the remote endpoint of the tunnel
(i.e., the destination address used in the outer IP
header). If the address is unknown or the tunnel is
not a point-to-point link (e.g., if it is a 6to4
tunnel), the value is 0.0.0.0 for tunnels over IPv4 or
:: for tunnels over IPv6."
::= { tunnelIfEntry 10 }
tunnelConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF TunnelConfigEntry
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"The (conceptual) table containing information on
configured tunnels. This table can be used to map a
set of tunnel endpoints to the associated ifIndex
value. It can also be used for row creation. Note
that every row in the tunnelIfTable with a fixed IPv4
destination address should have a corresponding row in
the tunnelConfigTable, regardless of whether it was
created via SNMP. This table is deprecated in favor
of tunnelInetConfigTable."
::= { tunnel 2 }
tunnelConfigEntry OBJECT-TYPE
SYNTAX TunnelConfigEntry
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"An entry (conceptual row) containing the information
on a particular configured tunnel."
INDEX { tunnelConfigLocalAddress,
tunnelConfigRemoteAddress,
tunnelConfigEncapsMethod,
tunnelConfigID }
::= { tunnelConfigTable 1 }
TunnelConfigEntry ::= SEQUENCE {
tunnelConfigLocalAddress IpAddress,
tunnelConfigRemoteAddress IpAddress,
tunnelConfigEncapsMethod IANAtunnelType,
tunnelConfigID Integer32,
tunnelConfigIfIndex InterfaceIndexOrZero,
tunnelConfigStatus RowStatus
Expires July 2004 [Page 10]
Draft Inet Tunnel MIB January 2004
}
tunnelConfigLocalAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"The address of the local endpoint of the tunnel, or
0.0.0.0 if the device is free to choose any of its
addresses at tunnel establishment time."
::= { tunnelConfigEntry 1 }
tunnelConfigRemoteAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"The address of the remote endpoint of the tunnel."
::= { tunnelConfigEntry 2 }
tunnelConfigEncapsMethod OBJECT-TYPE
SYNTAX IANAtunnelType
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"The encapsulation method used by the tunnel."
::= { tunnelConfigEntry 3 }
tunnelConfigID OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"An identifier used to distinguish between multiple
tunnels of the same encapsulation method, with the
same endpoints. If the encapsulation protocol only
allows one tunnel per set of endpoint addresses (such
as for GRE or IP-in-IP), the value of this object is
1. For encapsulation methods (such as L2F) which
allow multiple parallel tunnels, the manager is
responsible for choosing any ID which does not
conflict with an existing row, such as choosing a
random number."
::= { tunnelConfigEntry 4 }
Expires July 2004 [Page 11]
Draft Inet Tunnel MIB January 2004
tunnelConfigIfIndex OBJECT-TYPE
SYNTAX InterfaceIndexOrZero
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"If the value of tunnelConfigStatus for this row is
active, then this object contains the value of ifIndex
corresponding to the tunnel interface. A value of 0
is not legal in the active state, and means that the
interface index has not yet been assigned."
::= { tunnelConfigEntry 5 }
tunnelConfigStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"The status of this row, by which new entries may be
created, or old entries deleted from this table. The
agent need not support setting this object to
createAndWait or notInService since there are no other
writable objects in this table, and writable objects
in rows of corresponding tables such as the
tunnelIfTable may be modified while this row is
active.
To create a row in this table for an encapsulation
method which does not support multiple parallel
tunnels with the same endpoints, the management
station should simply use a tunnelConfigID of 1, and
set tunnelConfigStatus to createAndGo. For
encapsulation methods such as L2F which allow multiple
parallel tunnels, the management station may select a
pseudo-random number to use as the tunnelConfigID and
set tunnelConfigStatus to createAndGo. In the event
that this ID is already in use and an
inconsistentValue is returned in response to the set
operation, the management station should simply select
a new pseudo-random number and retry the operation.
Creating a row in this table will cause an interface
index to be assigned by the agent in an
implementation-dependent manner, and corresponding
rows will be instantiated in the ifTable and the
tunnelIfTable. The status of this row will become
Expires July 2004 [Page 12]
Draft Inet Tunnel MIB January 2004
active as soon as the agent assigns the interface
index, regardless of whether the interface is
operationally up.
Deleting a row in this table will likewise delete the
corresponding row in the ifTable and in the
tunnelIfTable."
::= { tunnelConfigEntry 6 }
tunnelInetConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF TunnelInetConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The (conceptual) table containing information on
configured tunnels. This table can be used to map a
set of tunnel endpoints to the associated ifIndex
value. It can also be used for row creation. Note
that every row in the tunnelIfTable with a fixed
destination address should have a corresponding row in
the tunnelInetConfigTable, regardless of whether it
was created via SNMP."
::= { tunnel 3 }
tunnelInetConfigEntry OBJECT-TYPE
SYNTAX TunnelInetConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) containing the information
on a particular configured tunnel. Note that there is
a 128 subid maximum for object OIDs. In practice this
is not expected to be a problem since IPv4 and IPv6
addresses will not cause the limit to be reached. If
other types are supported by an agent, care must be
taken to ensure that the sum of the lengths do not
cause the limit to be exceeded."
INDEX { tunnelInetConfigAddressType,
tunnelInetConfigLocalAddress,
tunnelInetConfigRemoteAddress,
tunnelInetConfigEncapsMethod,
tunnelInetConfigID }
::= { tunnelInetConfigTable 1 }
TunnelInetConfigEntry ::= SEQUENCE {
Expires July 2004 [Page 13]
Draft Inet Tunnel MIB January 2004
tunnelInetConfigAddressType InetAddressType,
tunnelInetConfigLocalAddress InetAddress,
tunnelInetConfigRemoteAddress InetAddress,
tunnelInetConfigEncapsMethod IANAtunnelType,
tunnelInetConfigID Integer32,
tunnelInetConfigIfIndex InterfaceIndexOrZero,
tunnelInetConfigStatus RowStatus,
tunnelInetConfigStorageType StorageType
}
tunnelInetConfigAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The address type over which the tunnel encapsulates
packets."
::= { tunnelInetConfigEntry 1 }
tunnelInetConfigLocalAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The address of the local endpoint of the tunnel, or
0.0.0.0 if the device is free to choose any of its
addresses at tunnel establishment time."
::= { tunnelInetConfigEntry 2 }
tunnelInetConfigRemoteAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The address of the remote endpoint of the tunnel."
::= { tunnelInetConfigEntry 3 }
tunnelInetConfigEncapsMethod OBJECT-TYPE
SYNTAX IANAtunnelType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The encapsulation method used by the tunnel."
::= { tunnelInetConfigEntry 4 }
Expires July 2004 [Page 14]
Draft Inet Tunnel MIB January 2004
tunnelInetConfigID OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An identifier used to distinguish between multiple
tunnels of the same encapsulation method, with the
same endpoints. If the encapsulation protocol only
allows one tunnel per set of endpoint addresses (such
as for GRE or IP-in-IP), the value of this object is
1. For encapsulation methods (such as L2F) which
allow multiple parallel tunnels, the manager is
responsible for choosing any ID which does not
conflict with an existing row, such as choosing a
random number."
::= { tunnelInetConfigEntry 5 }
tunnelInetConfigIfIndex OBJECT-TYPE
SYNTAX InterfaceIndexOrZero
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If the value of tunnelInetConfigStatus for this row
is active, then this object contains the value of
ifIndex corresponding to the tunnel interface. A
value of 0 is not legal in the active state, and means
that the interface index has not yet been assigned."
::= { tunnelInetConfigEntry 6 }
tunnelInetConfigStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this row, by which new entries may be
created, or old entries deleted from this table. The
agent need not support setting this object to
createAndWait or notInService since there are no other
writable objects in this table, and writable objects
in rows of corresponding tables such as the
tunnelIfTable may be modified while this row is
active.
To create a row in this table for an encapsulation
method which does not support multiple parallel
Expires July 2004 [Page 15]
Draft Inet Tunnel MIB January 2004
tunnels with the same endpoints, the management
station should simply use a tunnelInetConfigID of 1,
and set tunnelInetConfigStatus to createAndGo. For
encapsulation methods such as L2F which allow multiple
parallel tunnels, the management station may select a
pseudo-random number to use as the tunnelInetConfigID
and set tunnelInetConfigStatus to createAndGo. In the
event that this ID is already in use and an
inconsistentValue is returned in response to the set
operation, the management station should simply select
a new pseudo-random number and retry the operation.
Creating a row in this table will cause an interface
index to be assigned by the agent in an
implementation-dependent manner, and corresponding
rows will be instantiated in the ifTable and the
tunnelIfTable. The status of this row will become
active as soon as the agent assigns the interface
index, regardless of whether the interface is
operationally up.
Deleting a row in this table will likewise delete the
corresponding row in the ifTable and in the
tunnelIfTable."
::= { tunnelInetConfigEntry 7 }
tunnelInetConfigStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The storage type of this row. If the row is
permanent(4), no objects in the row need be writable."
::= { tunnelInetConfigEntry 8 }
-- conformance information
tunnelMIBConformance
OBJECT IDENTIFIER ::= { tunnelMIB 2 }
tunnelMIBCompliances
OBJECT IDENTIFIER ::= { tunnelMIBConformance 1 }
tunnelMIBGroups OBJECT IDENTIFIER ::= { tunnelMIBConformance 2 }
-- compliance statements
Expires July 2004 [Page 16]
Draft Inet Tunnel MIB January 2004
tunnelMIBCompliance MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"The (deprecated) IPv4-only compliance statement for
the IP Tunnel MIB."
MODULE -- this module
MANDATORY-GROUPS { tunnelMIBGroup }
OBJECT tunnelIfHopLimit
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT tunnelIfTOS
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT tunnelConfigStatus
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
::= { tunnelMIBCompliances 1 }
tunnelMIBInetReadWriteCompliance MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"The full compliance statement for the IP Tunnel MIB."
MODULE -- this module
MANDATORY-GROUPS { tunnelMIBInetGroup }
OBJECT tunnelIfAddressType
SYNTAX InetAddressType { ipv4(1), ipv6(2),
ipv4z(3), ipv6z(4) }
DESCRIPTION
"An implementation is only required to support IPv4
and/or IPv6 addresses. An implementation only needs to
support the addresses it actually supports on the
device."
OBJECT tunnelInetConfigStatus
SYNTAX RowStatus { active(1) }
WRITE-SYNTAX RowStatus { createAndGo(4), destroy(6) }
DESCRIPTION
"Support for createAndWait and notInService is not
Expires July 2004 [Page 17]
Draft Inet Tunnel MIB January 2004
required."
::= { tunnelMIBCompliances 2 }
tunnelMIBInetReadOnlyCompliance MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"The read-only compliance statement for the IP Tunnel
MIB."
MODULE -- this module
MANDATORY-GROUPS { tunnelMIBInetGroup }
OBJECT tunnelIfHopLimit
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT tunnelIfTOS
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT tunnelIfFlowLabel
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT tunnelIfAddressType
SYNTAX InetAddressType { ipv4(1), ipv6(2),
ipv4z(3), ipv6z(4) }
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required.
An implementation is only required to support IPv4
and/or IPv6 addresses. An implementation only needs to
support the addresses it actually supports on the
device."
OBJECT tunnelIfLocalInetAddress
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT tunnelIfRemoteInetAddress
MIN-ACCESS read-only
Expires July 2004 [Page 18]
Draft Inet Tunnel MIB January 2004
DESCRIPTION
"Write access is not required."
OBJECT tunnelInetConfigStatus
SYNTAX RowStatus { active(1) }
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required, and active is the only
status that needs to be supported."
OBJECT tunnelInetConfigStorageType
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
::= { tunnelMIBCompliances 3 }
-- units of conformance
tunnelMIBGroup OBJECT-GROUP
OBJECTS { tunnelIfLocalAddress, tunnelIfRemoteAddress,
tunnelIfEncapsMethod, tunnelIfHopLimit, tunnelIfTOS,
tunnelIfSecurity, tunnelConfigIfIndex, tunnelConfigStatus }
STATUS deprecated
DESCRIPTION
"A collection of objects to support basic management
of IPv4 Tunnels."
::= { tunnelMIBGroups 1 }
tunnelMIBInetGroup OBJECT-GROUP
OBJECTS { tunnelIfAddressType, tunnelIfLocalInetAddress,
tunnelIfRemoteInetAddress, tunnelIfEncapsMethod,
tunnelIfHopLimit, tunnelIfTOS, tunnelIfFlowLabel,
tunnelIfSecurity, tunnelInetConfigIfIndex,
tunnelInetConfigStatus, tunnelInetConfigStorageType }
STATUS current
DESCRIPTION
"A collection of objects to support basic management
of IPv4 and IPv6 Tunnels."
::= { tunnelMIBGroups 2 }
END
Expires July 2004 [Page 19]
Draft Inet Tunnel MIB January 2004
5. IANA Considerations
This document introduces a new IANA-maintained textual convention
(TC) which is to be added to the IANAifType-MIB. The initial
version of this IANAtunnelType TC can be found in Appendix A. The
current version of the textual convention can be accessed at
http://www.iana.org/assignments/ianaiftype-mib
The policy for assigning new IANAtunnelType values is First Come
First Served, as defined in [RFC2434], just as it is for new
IANAifTypes values. The assignment policy for IANAtunnelType
values should always be identical to the policy for assigning
IANAifType values.
New types of tunnels over IPv4 or IPv6 should not be assigned
IANAifType values. Instead, they should be assigned
IANAtunnelType values and hence reuse the interface type
tunnel(131). (Note this restriction does not apply to "tunnels"
which are not over IPv4 or IPv6.)
Previously tunnel types which were not point-to-point tunnels were
problematic in that they could not be properly expressed in the
tunnel MIB, and hence were assigned IANAifType values. This
document now corrects this problem, and as a result, IANA should
deprecate the sixToFour(215) IANAifType value in favor of the
sixToFour(11) IANAtunnelType value.
6. Security Considerations
There are a number of management objects defined in this MIB
module with a MAX-ACCESS clause of read-write and/or read-create.
Such objects may be considered sensitive or vulnerable in some
network environments. The support for SET operations in a non-
secure environment without proper protection can have a negative
effect on network operations.
Unauthorized write access to any of the writable objects could
cause unauthorized creation and/or manipulation of tunnels,
resulting in a denial of service, or redirection of packets to an
arbitrary destination.
Some of the readable objects in this MIB module (i.e., objects
with a MAX-ACCESS other than not-accessible) may be considered
sensitive or vulnerable in some network environments. It is thus
Expires July 2004 [Page 20]
Draft Inet Tunnel MIB January 2004
important to control even GET and/or NOTIFY access to these
objects and possibly to even encrypt the values of these objects
when sending them over the network via SNMP.
Unauthorized read access to tunnelIfLocalInetAddress,
tunnelIfRemoteInetAddress, tunnelIfLocalAddress,
tunnelIfRemoteAddress, or any object in the tunnelConfigTable or
tunnelInetConfigTable would reveal information about the tunnel
topology.
SNMP versions prior to SNMPv3 did not include adequate security.
Even if the network itself is secure (for example by using IPSec),
even then, there is no control as to who on the secure network is
allowed to access and GET/SET (read/change/create/delete) the
objects in this MIB module.
It is RECOMMENDED that implementers consider the security features
as provided by the SNMPv3 framework (see [RFC3410], section 8),
including full support for the SNMPv3 cryptographic mechanisms
(for authentication and privacy).
Further, deployment of SNMP versions prior to SNMPv3 is NOT
RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to
enable cryptographic security. It is then a customer/operator
responsibility to ensure that the SNMP entity giving access to an
instance of this MIB module is properly configured to give access
to the objects only to those principals (users) that have
legitimate rights to indeed GET or SET (change/create/delete)
them.
7. Acknowledgements
This MIB module was updated based on feedback from the IETF's
Interfaces MIB (IF-MIB) and Point-to-Point Protocol Extensions
(PPPEXT) Working Groups.
8. Authors' Addresses
Dave Thaler
Microsoft Corporation
One Microsoft Way
Redmond, WA 98052-6399
Expires July 2004 [Page 21]
Draft Inet Tunnel MIB January 2004
Phone: +1 425 703 8835
EMail: dthaler@microsoft.com
9. Normative References
[RFC2434] Narten, T. and H. Alvestrand, "Guidelines for Writing
an IANA Considerations Section in RFCs", RFC 2434,
October 1998.
[RFC2578] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case,
J., Rose, M. and S. Waldbusser, "Structure of
Management Information Version 2 (SMIv2)", STD 58, RFC
2578, April 1999.
[RFC2579] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case,
J., Rose, M. and S. Waldbusser, "Textual Conventions
for SMIv2", STD 58, RFC 2579, April 1999.
[RFC2580] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case,
J., Rose, M. and S. Waldbusser, "Conformance
Statements for SMIv2", STD 58, RFC 2580, April 1999.
[RFC2863] McCloghrie, K. and F. Kastenholz. "The Interfaces
Group MIB", RFC 2863, June 2000.
[RFC3595] B. Wijnen, "Textual Conventions for IPv6 Flow Label",
RFC 3595, September 2003.
10. Informative References
[RFC1234] D. Provan, "Tunneling IPX Traffic through IP
Networks", RFC 1234, June 1991.
[RFC1241] Woodburn, R. and D. Mills, "A Scheme for an Internet
Encapsulation Protocol: Version 1", RFC 1241, July
1991.
[RFC1701] Hanks, S., Li, T., Farinacci, D. and P. Traina,
"Generic Routing Encapsulation (GRE)", RFC 1701,
October 1994.
[RFC1702] Hanks, S., Li, T., Farinacci, D. and P. Traina,
"Generic Routing Encapsulation over IPv4 networks",
Expires July 2004 [Page 22]
Draft Inet Tunnel MIB January 2004
RFC 1702, October 1994.
[RFC2003] Perkins, C., "IP Encapsulation within IP", RFC 2003,
October 1996.
[RFC2004] Perkins, C., "Minimal Encapsulation within IP", RFC
2004, October 1996.
[RFC2107] Hamzeh, K., "Ascend Tunnel Management Protocol -
ATMP", RFC 2107, February 1997.
[RFC2341] Valencia, A., Littlewood, M. and T. Kolar. "Cisco
Layer Two Forwarding (Protocol) "L2F"", RFC 2341, May
1998.
[RFC2401] R. Atkinson, "Security architecture for the internet
protocol", RFC 2401, November 1998.
[RFC2474] Nichols, K., Blake, S., Baker, F. and D. Black.
"Definition of the Differentiated Services Field (DS
Field) in the IPv4 and IPv6 Headers", RFC 2474,
December 1998.
[RFC2637] Hamzeh, K., Pall, G., Verthein, W. Taarud, J., Little,
W. and G. Zorn, "Point-to-Point Tunneling Protocol",
RFC 2637, July 1999.
[RFC2661] Townsley, W., Valencia, A., Rubens, A., Pall, G.,
Zorn, G. and B. Palter, "Layer Two Tunneling Protocol
"L2TP"", RFC 2661, August 1999.
[RFC2893] Gilligan, R. and E. Nordmark. "Transition Mechanisms
for IPv6 Hosts and Routers", RFC 2893, August 2000.
[RFC3410] Case, J., Mundy, R., Partain, D. and B. Stewart,
"Introduction and Applicability Statements for
Internet-Standard Management Framework", RFC 3410,
December 2002.
11. Appendix A: IANA Tunnel Type TC
This appendix defines the initial content of the IANAtunnelType
textual convention which should appear in the IANAifType-MIB.
Expires July 2004 [Page 23]
Draft Inet Tunnel MIB January 2004
IANAtunnelType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The encapsulation method used by a tunnel. The value
direct indicates that a packet is encapsulated
directly within a normal IP header, with no
intermediate header, and unicast to the remote tunnel
endpoint (e.g., an RFC 2003 IP-in-IP tunnel, or an RFC
1933 IPv6-in-IPv4 tunnel). The value minimal indicates
that a Minimal Forwarding Header (RFC 2004) is
inserted between the outer header and the payload
packet. The value UDP indicates that the payload
packet is encapsulated within a normal UDP packet
(e.g., RFC 1234).
The values sixToFour, sixOverFour, and isatap
indicates that an IPv6 packet is encapsulated directly
within an IPv4 header, with no intermediate header,
and unicast to the destination determined by the 6to4,
6over4, or ISATAP protocol.
The remaining protocol-specific values indicate that a
header of the protocol of that name is inserted
between the outer header and the payload header."
SYNTAX INTEGER {
other(1), -- none of the following
direct(2), -- no intermediate header
gre(3), -- GRE encapsulation
minimal(4), -- Minimal encapsulation
l2tp(5), -- L2TP encapsulation
pptp(6), -- PPTP encapsulation
l2f(7), -- L2F encapsulation
udp(8), -- UDP encapsulation
atmp(9), -- ATMP encapsulation
msdp(10), -- MSDP encapsulation
sixToFour(11), -- 6to4 encapsulation
sixOverFour(12), -- 6over4 encapsulation
isatap(13), -- ISATAP encapsulation
teredo(14) -- Teredo encapsulation
}
Expires July 2004 [Page 24]
Draft Inet Tunnel MIB January 2004
12. Full Copyright Statement
Copyright (C) The Internet Society (2004). All Rights Reserved.
This document and translations of it may be copied and furnished
to others, and derivative works that comment on or otherwise
explain it or assist in its implmentation may be prepared, copied,
published and distributed, in whole or in part, without
restriction of any kind, provided that the above copyright notice
and this paragraph are included on all such copies and derivative
works. However, this document itself may not be modified in any
way, such as by removing the copyright notice or references to the
Internet Society or other Internet organizations, except as needed
for the purpose of developing Internet standards in which case the
procedures for copyrights defined in the Internet Standards
process must be followed, or as required to translate it into
languages other than English.
The limited permissions granted above are perpetual and will not
be revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on
an "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET
ENGINEERING TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
13. Intellectual Property
The IETF takes no position regarding the validity or scope of any
intellectual property or other rights that might be claimed to
pertain to the implementation or use of the technology described
in this document or the extent to which any license under such
rights might or might not be available; neither does it represent
that it has made any effort to identify any such rights.
Information on the IETF's procedures with respect to rights in
standards-track and standards-related documentation can be found
in BCP-11. Copies of claims of rights made available for
publication and any assurances of licenses to be made available,
or the result of an attempt made to obtain a general license or
permission for the use of such proprietary rights by implementors
or users of this specification can be obtained from the IETF
Secretariat.
Expires July 2004 [Page 25]
Draft Inet Tunnel MIB January 2004
The IETF invites any interested party to bring to its attention
any copyrights, patents or patent applications, or other
proprietary rights which may cover technology that may be required
to practice this standard. Please address the information to the
IETF Executive Director."
Expires July 2004 [Page 26]