MASQUE                                                       D. Schinazi
Internet-Draft                                                Google LLC
Intended status: Standards Track                             8 June 2022
Expires: 10 December 2022


                          Proxying UDP in HTTP
                    draft-ietf-masque-connect-udp-14

Abstract

   This document describes how to proxy UDP in HTTP, similar to how the
   HTTP CONNECT method allows proxying TCP in HTTP.  More specifically,
   this document defines a protocol that allows an HTTP client to create
   a tunnel for UDP communications through an HTTP server that acts as a
   proxy.

About This Document

   This note is to be removed before publishing as an RFC.

   The latest revision of this draft can be found at https://ietf-wg-
   masque.github.io/draft-ietf-masque-connect-udp/draft-ietf-masque-
   connect-udp.html.  Status information for this document may be found
   at https://datatracker.ietf.org/doc/draft-ietf-masque-connect-udp/.

   Discussion of this document takes place on the MASQUE Working Group
   mailing list (mailto:masque@ietf.org), which is archived at
   https://mailarchive.ietf.org/arch/browse/masque/.

   Source for this draft and an issue tracker can be found at
   https://github.com/ietf-wg-masque/draft-ietf-masque-connect-udp.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at https://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."




Schinazi                Expires 10 December 2022                [Page 1]


Internet-Draft            Proxying UDP in HTTP                 June 2022


   This Internet-Draft will expire on 10 December 2022.

Copyright Notice

   Copyright (c) 2022 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents (https://trustee.ietf.org/
   license-info) in effect on the date of publication of this document.
   Please review these documents carefully, as they describe your rights
   and restrictions with respect to this document.  Code Components
   extracted from this document must include Revised BSD License text as
   described in Section 4.e of the Trust Legal Provisions and are
   provided without warranty as described in the Revised BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   2
     1.1.  Conventions and Definitions . . . . . . . . . . . . . . .   3
   2.  Client Configuration  . . . . . . . . . . . . . . . . . . . .   3
   3.  Tunnelling UDP over HTTP  . . . . . . . . . . . . . . . . . .   4
     3.1.  UDP Proxy Handling  . . . . . . . . . . . . . . . . . . .   5
     3.2.  HTTP/1.1 Request  . . . . . . . . . . . . . . . . . . . .   6
     3.3.  HTTP/1.1 Response . . . . . . . . . . . . . . . . . . . .   7
     3.4.  HTTP/2 and HTTP/3 Requests  . . . . . . . . . . . . . . .   8
     3.5.  HTTP/2 and HTTP/3 Responses . . . . . . . . . . . . . . .   8
     3.6.  Note About Draft Versions . . . . . . . . . . . . . . . .   9
   4.  Context Identifiers . . . . . . . . . . . . . . . . . . . . .   9
   5.  HTTP Datagram Payload Format  . . . . . . . . . . . . . . . .  10
   6.  Performance Considerations  . . . . . . . . . . . . . . . . .  11
     6.1.  MTU Considerations  . . . . . . . . . . . . . . . . . . .  12
     6.2.  Tunneling of ECN Marks  . . . . . . . . . . . . . . . . .  12
   7.  Security Considerations . . . . . . . . . . . . . . . . . . .  13
   8.  IANA Considerations . . . . . . . . . . . . . . . . . . . . .  13
     8.1.  HTTP Upgrade Token  . . . . . . . . . . . . . . . . . . .  13
     8.2.  Well-Known URI  . . . . . . . . . . . . . . . . . . . . .  13
   9.  References  . . . . . . . . . . . . . . . . . . . . . . . . .  14
     9.1.  Normative References  . . . . . . . . . . . . . . . . . .  14
     9.2.  Informative References  . . . . . . . . . . . . . . . . .  15
   Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . . .  16
   Author's Address  . . . . . . . . . . . . . . . . . . . . . . . .  16

1.  Introduction

   While HTTP provides the CONNECT method (see Section 9.3.6 of [HTTP])
   for creating a TCP [TCP] tunnel to a proxy, prior to this
   specification it lacked a method for doing so for UDP [UDP] traffic.



Schinazi                Expires 10 December 2022                [Page 2]


Internet-Draft            Proxying UDP in HTTP                 June 2022


   This document describes a protocol for tunnelling UDP to a server
   acting as a UDP-specific proxy over HTTP.  UDP tunnels are commonly
   used to create an end-to-end virtual connection, which can then be
   secured using QUIC [QUIC] or another protocol running over UDP.
   Unlike CONNECT, the UDP proxy itself is identified with an absolute
   URL containing the traffic's destination.  Clients generate those
   URLs using a URI Template [TEMPLATE], as described in Section 2.

   This protocol supports all existing versions of HTTP by using HTTP
   Datagrams [HTTP-DGRAM].  When using HTTP/2 [HTTP/2] or HTTP/3
   [HTTP/3], it uses HTTP Extended CONNECT as described in
   [EXT-CONNECT2] and [EXT-CONNECT3].  When using HTTP/1.x [HTTP/1.1],
   it uses HTTP Upgrade as defined in Section 7.8 of [HTTP].

1.1.  Conventions and Definitions

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
   "OPTIONAL" in this document are to be interpreted as described in
   BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all
   capitals, as shown here.

   In this document, we use the term "UDP proxy" to refer to the HTTP
   server that acts upon the client's UDP tunnelling request to open a
   UDP socket to a target server, and generates the response to this
   request.  If there are HTTP intermediaries (as defined in Section 3.7
   of [HTTP]) between the client and the UDP proxy, those are referred
   to as "intermediaries" in this document.

   Note that, when the HTTP version in use does not support multiplexing
   streams (such as HTTP/1.1), any reference to "stream" in this
   document represents the entire connection.

2.  Client Configuration

   HTTP clients are configured to use a UDP proxy with a URI Template
   [TEMPLATE] that has the variables "target_host" and "target_port".
   Examples are shown below:

https://masque.example.org/.well-known/masque/udp/{target_host}/{target_port}/
https://proxy.example.org:4443/masque?h={target_host}&p={target_port}
https://proxy.example.org:4443/masque{?target_host,target_port}

                   Figure 1: URI Template Examples

   The following requirements apply to the URI Template:

   *  The URI Template MUST be a level 3 template or lower.



Schinazi                Expires 10 December 2022                [Page 3]


Internet-Draft            Proxying UDP in HTTP                 June 2022


   *  The URI Template MUST be in absolute form, and MUST include non-
      empty scheme, authority and path components.

   *  The path component of the URI Template MUST start with a slash
      "/".

   *  All template variables MUST be within the path or query components
      of the URI.

   *  The URI template MUST contain the two variables "target_host" and
      "target_port" and MAY contain other variables.

   *  The URI Template MUST NOT contain any non-ASCII unicode characters
      and MUST only contain ASCII characters in the range 0x21-0x7E
      inclusive (note that percent-encoding is allowed).

   *  The URI Template MUST NOT use Reserved Expansion ("+" operator),
      Fragment Expansion ("#" operator), Label Expansion with Dot-
      Prefix, Path Segment Expansion with Slash-Prefix, nor Path-Style
      Parameter Expansion with Semicolon-Prefix.

   Clients SHOULD validate the requirements above; however, clients MAY
   use a general-purpose URI Template implementation that lacks this
   specific validation.  If a client detects that any of the
   requirements above are not met by a URI Template, the client MUST
   reject its configuration and fail the request without sending it to
   the UDP proxy.

   Since the original HTTP CONNECT method allowed conveying the target
   host and port but not the scheme, proxy authority, path, nor query,
   there exist clients with proxy configuration interfaces that only
   allow the user to configure the proxy host and the proxy port.
   Client implementations of this specification that are constrained by
   such limitations MAY attempt to access UDP proxying capabilities
   using the default template, which is defined as:
   "https://$PROXY_HOST:$PROXY_PORT/.well-known/masque/
   udp/{target_host}/{target_port}/" where $PROXY_HOST and $PROXY_PORT
   are the configured host and port of the UDP proxy respectively.  UDP
   proxy deployments SHOULD offer service at this location if they need
   to interoperate with such clients.

3.  Tunnelling UDP over HTTP

   To allow negotiation of a tunnel for UDP over HTTP, this document
   defines the "connect-udp" HTTP Upgrade Token.  The resulting UDP
   tunnels use the Capsule Protocol (see Section 3.2 of [HTTP-DGRAM])
   with HTTP Datagram in the format defined in Section 5.




Schinazi                Expires 10 December 2022                [Page 4]


Internet-Draft            Proxying UDP in HTTP                 June 2022


   To initiate a UDP tunnel associated with a single HTTP stream, a
   client issues a request containing the "connect-udp" upgrade token.
   The target of the tunnel is indicated by the client to the UDP proxy
   via the "target_host" and "target_port" variables of the URI
   Template, see Section 2.  If the request is successful, the UDP proxy
   commits to converting received HTTP Datagrams into UDP packets and
   vice versa until the tunnel is closed.

   When sending its UDP proxying request, the client SHALL perform URI
   Template expansion to determine the path and query of its request.
   target_host supports using DNS names, IPv6 literals and IPv4
   literals.  Note that this URI Template expansion requires using pct-
   encoding, so for example if the target_host is "2001:db8::42", it
   will be encoded in the URI as "2001%3Adb8%3A%3A42".

   By virtue of the definition of the Capsule Protocol (see
   [HTTP-DGRAM]), UDP proxying requests do not carry any message
   content.  Similarly, successful UDP proxying responses also do not
   carry any message content.

3.1.  UDP Proxy Handling

   Upon receiving a UDP proxying request:

   *  if the recipient is configured to use another HTTP proxy, it will
      act as an intermediary: it forwards the request to another HTTP
      server.  Note that such intermediaries may need to reencode the
      request if they forward it using a version of HTTP that is
      different from the one used to receive it, as the request encoding
      differs by version (see below).

   *  otherwise, the recipient will act as a UDP proxy: it extracts the
      "target_host" and "target_port" variables from the URI it has
      reconstructed from the request headers, and establishes a tunnel
      by directly opening a UDP socket to the requested target.

   Unlike TCP, UDP is connection-less.  The UDP proxy that opens the UDP
   socket has no way of knowing whether the destination is reachable.
   Therefore it needs to respond to the request without waiting for a
   packet from the target.  However, if the target_host is a DNS name,
   the UDP proxy MUST perform DNS resolution before replying to the HTTP
   request.  If errors occur during this process, the UDP proxy MUST
   fail the request and SHOULD send details using an appropriate "Proxy-
   Status" header field [PROXY-STATUS] (for example, if DNS resolution
   returns an error, the proxy can use the dns_error Proxy Error Type
   from Section 2.3.2 of [PROXY-STATUS]).





Schinazi                Expires 10 December 2022                [Page 5]


Internet-Draft            Proxying UDP in HTTP                 June 2022


   UDP proxies can use connected UDP sockets if their operating system
   supports them, as that allows the UDP proxy to rely on the kernel to
   only send it UDP packets that match the correct 5-tuple.  If the UDP
   proxy uses a non-connected socket, it MUST validate the IP source
   address and UDP source port on received packets to ensure they match
   the client's request.  Packets that do not match MUST be discarded by
   the UDP proxy.

   The lifetime of the socket is tied to the request stream.  The UDP
   proxy MUST keep the socket open while the request stream is open.  If
   a UDP proxy is notified by its operating system that its socket is no
   longer usable (for example, this can happen when an ICMP "Destination
   Unreachable" message is received, see Section 3.1 of [ICMP6]), it
   MUST close the request stream.  UDP proxies MAY choose to close
   sockets due to a period of inactivity, but they MUST close the
   request stream when closing the socket.  UDP proxies that close
   sockets after a period of inactivity SHOULD NOT use a period lower
   than two minutes, see Section 4.3 of [BEHAVE].

   A successful response (as defined in Section 3.3 and Section 3.5)
   indicates that the UDP proxy has opened a socket to the requested
   target and is willing to proxy UDP payloads.  Any response other than
   a successful response indicates that the request has failed, and the
   client MUST therefore abort the request.

   UDP proxies MUST NOT introduce fragmentation at the IP layer when
   forwarding HTTP Datagrams onto a UDP socket.  In IPv4, the Don't
   Fragment (DF) bit MUST be set if possible, to prevent fragmentation
   on the path.  Future extensions MAY remove these requirements.

3.2.  HTTP/1.1 Request

   When using HTTP/1.1 [HTTP/1.1], a UDP proxying request will meet the
   following requirements:

   *  the method SHALL be "GET".

   *  the request SHALL include a single "Host" header field containing
      the origin of the UDP proxy.

   *  the request SHALL include a "Connection" header field with value
      "Upgrade" (note that this requirement is case-insensitive as per
      Section 7.6.1 of [HTTP]).

   *  the request SHALL include an "Upgrade" header field with value
      "connect-udp".





Schinazi                Expires 10 December 2022                [Page 6]


Internet-Draft            Proxying UDP in HTTP                 June 2022


   For example, if the client is configured with URI Template
   "https://proxy.example.org/.well-known/masque/
   udp/{target_host}/{target_port}/" and wishes to open a UDP proxying
   tunnel to target 192.0.2.42:443, it could send the following request:

GET https://proxy.example.org/.well-known/masque/udp/192.0.2.42/443/ HTTP/1.1
Host: proxy.example.org
Connection: Upgrade
Upgrade: connect-udp

                  Figure 2: Example HTTP/1.1 Request

   In HTTP/1.1, this protocol uses the GET method to mimic the design of
   the WebSocket Protocol [WEBSOCKET].

3.3.  HTTP/1.1 Response

   The UDP proxy SHALL indicate a successful response by replying with
   the following requirements:

   *  the HTTP status code on the response SHALL be 101 (Switching
      Protocols).

   *  the reponse SHALL include a single "Connection" header field with
      value "Upgrade" (note that this requirement is case-insensitive as
      per Section 7.6.1 of [HTTP]).

   *  the response SHALL include a single "Upgrade" header field with
      value "connect-udp".

   *  the response SHALL NOT include any "Transfer-Encoding" or
      "Content-Length" header fields.

   If any of these requirements are not met, the client MUST treat this
   proxying attempt as failed and abort the connection.

   For example, the UDP proxy could respond with:

   HTTP/1.1 101 Switching Protocols
   Connection: Upgrade
   Upgrade: connect-udp

                    Figure 3: Example HTTP/1.1 Response








Schinazi                Expires 10 December 2022                [Page 7]


Internet-Draft            Proxying UDP in HTTP                 June 2022


3.4.  HTTP/2 and HTTP/3 Requests

   When using HTTP/2 [HTTP/2] or HTTP/3 [HTTP/3], UDP proxying requests
   use Extended CONNECT.  This requires that servers send an HTTP
   Setting as specified in [EXT-CONNECT2] and [EXT-CONNECT3], and that
   requests use HTTP pseudo-header fields with the following
   requirements:

   *  The ":method" pseudo-header field SHALL be "CONNECT".

   *  The ":protocol" pseudo-header field SHALL be "connect-udp".

   *  The ":authority" pseudo-header field SHALL contain the authority
      of the UDP proxy.

   *  The ":path" and ":scheme" pseudo-header fields SHALL NOT be empty.
      Their values SHALL contain the scheme and path from the URI
      Template after the URI template expansion process has been
      completed.

   A UDP proxying request that does not conform to these restrictions is
   malformed (see Section 8.1.1 of [HTTP/2]).

   For example, if the client is configured with URI Template
   "https://proxy.example.org/{target_host}/{target_port}/" and wishes
   to open a UDP proxying tunnel to target 192.0.2.42:443, it could send
   the following request:

   HEADERS
   :method = CONNECT
   :protocol = connect-udp
   :scheme = https
   :path = /.well-known/masque/udp/192.0.2.42/443/
   :authority = proxy.example.org

                      Figure 4: Example HTTP/2 Request

3.5.  HTTP/2 and HTTP/3 Responses

   The UDP proxy SHALL indicate a successful response by replying with
   any 2xx (Successful) HTTP status code, without any "Transfer-
   Encoding" or "Content-Length" header fields.

   If any of these requirements are not met, the client MUST treat this
   proxying attempt as failed and abort the request.

   For example, the UDP proxy could respond with:




Schinazi                Expires 10 December 2022                [Page 8]


Internet-Draft            Proxying UDP in HTTP                 June 2022


   HEADERS
   :status = 200

                     Figure 5: Example HTTP/2 Response

3.6.  Note About Draft Versions

   [[RFC editor: please remove this section before publication.]]

   In order to allow implementations to support multiple draft versions
   of this specification during its development, we introduce the
   "connect-udp-version" header field.  When sent by the client, it
   contains a list of draft numbers supported by the client (e.g.,
   "connect-udp-version: 0, 2").  When sent by the UDP proxy, it
   contains a single draft number selected by the UDP proxy from the
   list provided by the client (e.g., "connect-udp-version: 2").
   Sending this header field is RECOMMENDED but not required.  The
   "connect-udp-version" header field is a List Structured Field, see
   Section 3.1 of [STRUCT-FIELD].  Each list member MUST be an Integer.

4.  Context Identifiers

   The mechanism for proxying UDP in HTTP defined in this document
   allows future extensions to exchange HTTP Datagrams which carry
   different semantics from UDP payloads.  Some of these extensions can
   augment UDP payloads with additional data, while others can exchange
   data that is completely separate from UDP payloads.  In order to
   accomplish this, all HTTP Datagrams associated with UDP Proxying
   request streams start with a context ID, see Section 5.

   Context IDs are 62-bit integers (0 to 2^62-1).  Context IDs are
   encoded as variable-length integers, see Section 16 of [QUIC].  The
   context ID value of 0 is reserved for UDP payloads, while non-zero
   values are dynamically allocated: non-zero even-numbered context IDs
   are client-allocated, and odd-numbered context IDs are proxy-
   allocated.  The context ID namespace is tied to a given HTTP request:
   it is possible for a context ID with the same numeric value to be
   simultaneously allocated in distinct requests, potentially with
   different semantics.  Context IDs MUST NOT be re-allocated within a
   given HTTP namespace but MAY be allocated in any order.  The context
   ID allocation restrictions to the use of even-numbered and odd-
   numbered context IDs exist in order to avoid the need for
   synchronisation between endpoints.  However, once a context ID has
   been allocated, those restrictions do not apply to the use of the
   context ID: it can be used by any client or UDP proxy, independent of
   which endpoint initially allocated it.





Schinazi                Expires 10 December 2022                [Page 9]


Internet-Draft            Proxying UDP in HTTP                 June 2022


   Registration is the action by which an endpoint informs its peer of
   the semantics and format of a given context ID.  This document does
   not define how registration occurs.  Future extensions MAY use HTTP
   header fields or capsules to register contexts.  Depending on the
   method being used, it is possible for datagrams to be received with
   Context IDs which have not yet been registered, for instance due to
   reordering of the packet containing the datagram and the packet
   containing the registration message during transmission.

5.  HTTP Datagram Payload Format

   When HTTP Datagrams (see [HTTP-DGRAM]) are associated with UDP
   proxying request streams, the HTTP Datagram Payload field has the
   format defined in Figure 6.  Note that when HTTP Datagrams are
   encoded using QUIC DATAGRAM frames, the Context ID field defined
   below directly follows the Quarter Stream ID field which is at the
   start of the QUIC DATAGRAM frame payload:

   UDP Proxying HTTP Datagram Payload {
     Context ID (i),
     Payload (..),
   }

                Figure 6: UDP Proxying HTTP Datagram Format

   Context ID:  A variable-length integer (see Section 16 of [QUIC])
      that contains the value of the Context ID.  If an HTTP/3 datagram
      which carries an unknown Context ID is received, the receiver
      SHALL either drop that datagram silently or buffer it temporarily
      (on the order of a round trip) while awaiting the registration of
      the corresponding Context ID.
   Payload:  The payload of the datagram, whose semantics depend on
      value of the previous field.  Note that this field can be empty.

   UDP packets are encoded using HTTP Datagrams with the Context ID set
   to zero.  When the Context ID is set to zero, the Payload field
   contains the unmodified payload of a UDP packet (referred to as "data
   octets" in [UDP]).













Schinazi                Expires 10 December 2022               [Page 10]


Internet-Draft            Proxying UDP in HTTP                 June 2022


   By virtue of the definition of the UDP header [UDP], it is not
   possible to encode UDP payloads longer than 65527 bytes.  Therefore,
   endpoints MUST NOT send HTTP Datagrams with a Payload field longer
   than 65527 using Context ID zero.  An endpoint that receives a
   DATAGRAM capsule using Context ID zero whose Payload field is longer
   than 65527 MUST abort the stream.  If a UDP proxy knows it can only
   send out UDP packets of a certain length due to its underlying link
   MTU, it SHOULD discard incoming DATAGRAM capsules using Context ID
   zero whose Payload field is longer than that limit without buffering
   the capsule contents.

   If a UDP proxy receives an HTTP Datagram before it has received the
   corresponding request, it SHALL either drop that HTTP Datagram
   silently or buffer it temporarily (on the order of a round trip)
   while awaiting the corresponding request.

   Note that buffering datagrams (either because the request was not yet
   received, or because the Context ID is not yet known) consumes
   resources.  Receivers that buffer datagrams SHOULD apply buffering
   limits in order to reduce the risk of resource exhaustion occuring.
   For example, receivers can limit the total number of buffered
   datagrams, or the cumulative size of buffered datagrams, on a per-
   stream, per-context, or per-connection basis.

   A client MAY optimistically start sending UDP packets in HTTP
   Datagrams before receiving the response to its UDP proxying request.
   However, implementors should note that such proxied packets may not
   be processed by the UDP proxy if it responds to the request with a
   failure, or if the proxied packets are received by the UDP proxy
   before the request and the UDP proxy chooses to not buffer them.

6.  Performance Considerations

   Bursty traffic can often lead to temporally correlated packet losses,
   which in turn can lead to suboptimal responses from congestion
   controllers in protocols running over UDP.  To avoid this, UDP
   proxies SHOULD strive to avoid increasing burstiness of UDP traffic:
   they SHOULD NOT queue packets in order to increase batching.

   When the protocol running over UDP that is being proxied uses
   congestion control (e.g., [QUIC]), the proxied traffic will incur at
   least two nested congestion controllers.  This can reduce performance
   but the underlying HTTP connection MUST NOT disable congestion
   control unless it has an out-of-band way of knowing with absolute
   certainty that the inner traffic is congestion-controlled.






Schinazi                Expires 10 December 2022               [Page 11]


Internet-Draft            Proxying UDP in HTTP                 June 2022


   If a client or UDP proxy with a connection containing a UDP proxying
   request stream disables congestion control, it MUST NOT signal
   Explicit Congestion Notification (ECN) [ECN] support on that
   connection.  That is, it MUST mark all IP headers with the Not-ECT
   codepoint.  It MAY continue to report ECN feedback via QUIC ACK_ECN
   frames or the TCP "ECE" bit, as the peer may not have disabled
   congestion control.

   When the protocol running over UDP that is being proxied uses loss
   recovery (e.g., [QUIC]), and the underlying HTTP connection runs over
   TCP, the proxied traffic will incur at least two nested loss recovery
   mechanisms.  This can reduce performance as both can sometimes
   independently retransmit the same data.  To avoid this, UDP proxying
   SHOULD be performed over HTTP/3 to allow leveraging the QUIC DATAGRAM
   frame.

6.1.  MTU Considerations

   When using HTTP/3 with the QUIC Datagram extension [DGRAM], UDP
   payloads are transmitted in QUIC DATAGRAM frames.  Since those cannot
   be fragmented, they can only carry payloads up to a given length
   determined by the QUIC connection configuration and the path MTU.  If
   a UDP proxy is using QUIC DATAGRAM frames and it receives a UDP
   payload from the target that will not fit inside a QUIC DATAGRAM
   frame, the UDP proxy SHOULD NOT send the UDP payload in a DATAGRAM
   capsule, as that defeats the end-to-end unreliability characteristic
   that methods such as Datagram Packetization Layer Path MTU Discovery
   (DPLPMTUD) depend on [DPLPMTUD].  In this scenario, the UDP proxy
   SHOULD drop the UDP payload and send an ICMP "Packet Too Big" message
   to the target, see Section 3.2 of [ICMP6].

6.2.  Tunneling of ECN Marks

   UDP proxying does not create an IP-in-IP tunnel, so the guidance in
   [ECN-TUNNEL] about transferring ECN marks between inner and outer IP
   headers does not apply.  There is no inner IP header in UDP proxying
   tunnels.

   Note that UDP proxying clients do not have the ability in this
   specification to control the ECN codepoints on UDP packets the UDP
   proxy sends to the target, nor can UDP proxies communicate the
   markings of each UDP packet from target to UDP proxy.

   A UDP proxy MUST ignore ECN bits in the IP header of UDP packets
   received from the target, and MUST set the ECN bits to Not-ECT on UDP
   packets it sends to the target.  These do not relate to the ECN
   markings of packets sent between client and UDP proxy in any way.




Schinazi                Expires 10 December 2022               [Page 12]


Internet-Draft            Proxying UDP in HTTP                 June 2022


7.  Security Considerations

   There are significant risks in allowing arbitrary clients to
   establish a tunnel to arbitrary targets, as that could allow bad
   actors to send traffic and have it attributed to the UDP proxy.  HTTP
   servers that support UDP proxying ought to restrict its use to
   authenticated users.

   UDP proxies have similar properties to TCP proxies when it comes to
   facilitating denial of service attacks.  In theory the stateful
   nature of TCP provides better protection than stateless UDP but in
   practice this provides negligible benefits when considering proxying.
   Because the CONNECT method creates a TCP connection to the target,
   the target has to indicate its willingness to accept TCP connections
   by responding with a TCP SYN-ACK before the CONNECT proxy can send it
   application data.  UDP doesn't have this property, so a UDP proxy
   could send more data to an unwilling target than a CONNECT proxy.
   However, in practice denial of service attacks target open TCP ports
   so the TCP SYN-ACK does not offer much protection in real scenarios.
   While a UDP proxy could potentially limit the number of UDP packets
   it is willing to forward until it has observed a response from the
   target, that is unlikely to provide any protection against denial of
   service attacks because such attacks target open UDP ports where the
   protocol running over UDP would respond, and that would be
   interpreted as willingness to accept UDP by the UDP proxy.

   The security considerations described in [HTTP-DGRAM] also apply
   here.

8.  IANA Considerations

8.1.  HTTP Upgrade Token

   This document will request IANA to register "connect-udp" in the
   "HTTP Upgrade Tokens" registry maintained at
   <https://www.iana.org/assignments/http-upgrade-tokens>.

   Value:  connect-udp
   Description:  Proxying of UDP Payloads
   Expected Version Tokens:  None
   Reference:  This document

8.2.  Well-Known URI

   This document will request IANA to register "masque" in the "Well-
   Known URIs" registry maintained at <https://www.iana.org/assignments/
   well-known-uris>.




Schinazi                Expires 10 December 2022               [Page 13]


Internet-Draft            Proxying UDP in HTTP                 June 2022


   URI Suffix:  masque
   Change Controller:  IETF
   Reference:  This document
   Status:  permanent (if this document is approved)
   Related Information:  Includes all resources identified with the path
      prefix "/.well-known/masque/udp/"

9.  References

9.1.  Normative References

   [DGRAM]    Pauly, T., Kinnear, E., and D. Schinazi, "An Unreliable
              Datagram Extension to QUIC", RFC 9221,
              DOI 10.17487/RFC9221, March 2022,
              <https://www.rfc-editor.org/rfc/rfc9221>.

   [ECN]      Ramakrishnan, K., Floyd, S., and D. Black, "The Addition
              of Explicit Congestion Notification (ECN) to IP",
              RFC 3168, DOI 10.17487/RFC3168, September 2001,
              <https://www.rfc-editor.org/rfc/rfc3168>.

   [EXT-CONNECT2]
              McManus, P., "Bootstrapping WebSockets with HTTP/2",
              RFC 8441, DOI 10.17487/RFC8441, September 2018,
              <https://www.rfc-editor.org/rfc/rfc8441>.

   [EXT-CONNECT3]
              Hamilton, R., "Bootstrapping WebSockets with HTTP/3", Work
              in Progress, Internet-Draft, draft-ietf-httpbis-h3-
              websockets-04, 8 February 2022,
              <https://datatracker.ietf.org/doc/html/draft-ietf-httpbis-
              h3-websockets-04>.

   [HTTP]     Fielding, R., Ed., Nottingham, M., Ed., and J. Reschke,
              Ed., "HTTP Semantics", STD 97, RFC 9110,
              DOI 10.17487/RFC9110, June 2022,
              <https://www.rfc-editor.org/rfc/rfc9110>.

   [HTTP-DGRAM]
              Schinazi, D. and L. Pardue, "HTTP Datagrams and the
              Capsule Protocol", Work in Progress, Internet-Draft,
              draft-ietf-masque-h3-datagram-10, 8 June 2022,
              <https://datatracker.ietf.org/doc/html/draft-ietf-masque-
              h3-datagram-10>.

   [HTTP/1.1] Fielding, R., Ed., Nottingham, M., Ed., and J. Reschke,
              Ed., "HTTP/1.1", STD 99, RFC 9112, DOI 10.17487/RFC9112,
              June 2022, <https://www.rfc-editor.org/rfc/rfc9112>.



Schinazi                Expires 10 December 2022               [Page 14]


Internet-Draft            Proxying UDP in HTTP                 June 2022


   [HTTP/2]   Thomson, M., Ed. and C. Benfield, Ed., "HTTP/2", RFC 9113,
              DOI 10.17487/RFC9113, June 2022,
              <https://www.rfc-editor.org/rfc/rfc9113>.

   [HTTP/3]   Bishop, M., Ed., "HTTP/3", RFC 9114, DOI 10.17487/RFC9114,
              June 2022, <https://www.rfc-editor.org/rfc/rfc9114>.

   [PROXY-STATUS]
              Nottingham, M. and P. Sikora, "The Proxy-Status HTTP
              Response Header Field", Work in Progress, Internet-Draft,
              draft-ietf-httpbis-proxy-status-08, 13 October 2021,
              <https://datatracker.ietf.org/doc/html/draft-ietf-httpbis-
              proxy-status-08>.

   [QUIC]     Iyengar, J., Ed. and M. Thomson, Ed., "QUIC: A UDP-Based
              Multiplexed and Secure Transport", RFC 9000,
              DOI 10.17487/RFC9000, May 2021,
              <https://www.rfc-editor.org/rfc/rfc9000>.

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/RFC2119, March 1997,
              <https://www.rfc-editor.org/rfc/rfc2119>.

   [RFC8174]  Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
              2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
              May 2017, <https://www.rfc-editor.org/rfc/rfc8174>.

   [STRUCT-FIELD]
              Nottingham, M. and P-H. Kamp, "Structured Field Values for
              HTTP", RFC 8941, DOI 10.17487/RFC8941, February 2021,
              <https://www.rfc-editor.org/rfc/rfc8941>.

   [TCP]      Postel, J., "Transmission Control Protocol", STD 7,
              RFC 793, DOI 10.17487/RFC0793, September 1981,
              <https://www.rfc-editor.org/rfc/rfc793>.

   [TEMPLATE] Gregorio, J., Fielding, R., Hadley, M., Nottingham, M.,
              and D. Orchard, "URI Template", RFC 6570,
              DOI 10.17487/RFC6570, March 2012,
              <https://www.rfc-editor.org/rfc/rfc6570>.

   [UDP]      Postel, J., "User Datagram Protocol", STD 6, RFC 768,
              DOI 10.17487/RFC0768, August 1980,
              <https://www.rfc-editor.org/rfc/rfc768>.

9.2.  Informative References




Schinazi                Expires 10 December 2022               [Page 15]


Internet-Draft            Proxying UDP in HTTP                 June 2022


   [BEHAVE]   Audet, F., Ed. and C. Jennings, "Network Address
              Translation (NAT) Behavioral Requirements for Unicast
              UDP", BCP 127, RFC 4787, DOI 10.17487/RFC4787, January
              2007, <https://www.rfc-editor.org/rfc/rfc4787>.

   [DPLPMTUD] Fairhurst, G., Jones, T., Tüxen, M., Rüngeler, I., and T.
              Völker, "Packetization Layer Path MTU Discovery for
              Datagram Transports", RFC 8899, DOI 10.17487/RFC8899,
              September 2020, <https://www.rfc-editor.org/rfc/rfc8899>.

   [ECN-TUNNEL]
              Briscoe, B., "Tunnelling of Explicit Congestion
              Notification", RFC 6040, DOI 10.17487/RFC6040, November
              2010, <https://www.rfc-editor.org/rfc/rfc6040>.

   [ICMP6]    Conta, A., Deering, S., and M. Gupta, Ed., "Internet
              Control Message Protocol (ICMPv6) for the Internet
              Protocol Version 6 (IPv6) Specification", STD 89,
              RFC 4443, DOI 10.17487/RFC4443, March 2006,
              <https://www.rfc-editor.org/rfc/rfc4443>.

   [WEBSOCKET]
              Fette, I. and A. Melnikov, "The WebSocket Protocol",
              RFC 6455, DOI 10.17487/RFC6455, December 2011,
              <https://www.rfc-editor.org/rfc/rfc6455>.

Acknowledgments

   This document is a product of the MASQUE Working Group, and the
   author thanks all MASQUE enthusiasts for their contibutions.  This
   proposal was inspired directly or indirectly by prior work from many
   people.  In particular, the author would like to thank Eric Rescorla
   for suggesting to use an HTTP method to proxy UDP.  The author is
   indebted to Mark Nottingham and Lucas Pardue for the many
   improvements they contributed to this document.  The extensibility
   design in this document came out of the HTTP Datagrams Design Team,
   whose members were Alan Frindell, Alex Chernyakhovsky, Ben Schwartz,
   Eric Rescorla, Lucas Pardue, Marcus Ihlar, Martin Thomson, Mike
   Bishop, Tommy Pauly, Victor Vasiliev, and the author of this
   document.

Author's Address

   David Schinazi
   Google LLC
   1600 Amphitheatre Parkway
   Mountain View, CA 94043
   United States of America



Schinazi                Expires 10 December 2022               [Page 16]


Internet-Draft            Proxying UDP in HTTP                 June 2022


   Email: dschinazi.ietf@gmail.com


















































Schinazi                Expires 10 December 2022               [Page 17]