Internet Draft M. Stiemerling
Document: draft-ietf-midcom-semantics-07.txt J. Quittek
Expires: July 2004 NEC Europe Ltd.
Tom Taylor
Nortel Networks
January 2004
MIDCOM Protocol Semantics
<draft-ietf-midcom-semantics-07.txt>
Status of this Memo
This document is an Internet-Draft and is in full conformance with
all provisions of Section 10 of RFC 2026. Internet-Drafts are
working documents of the Internet Engineering Task Force (IETF), its
areas, and its working groups. Note that other groups may also
distribute working documents as Internet-Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html
Distribution of this document is unlimited.
Copyright Notice
Copyright (C) The Internet Society (2004). All Rights Reserved.
Abstract
This memo specifies semantics for a Middlebox Communication (MIDCOM)
protocol to be used by MIDCOM agents for interacting with
middleboxes, such as firewalls and NATs. The semantics discussion
does not include any specification of a concrete syntax or a
transport protocol. However, a concrete protocol is expected to
implement the specified semantics or - more probably - a superset of
it. The MIDCOM protocol semantics is derived from the MIDCOM
requirements, from the MIDCOM framework, and from working group
decisions.
Stiemerling, Quittek, Taylor [Page 1]
Internet-Draft MIDCOM Protocol Semantics January 2004
Table of Contents
1 Introduction ................................................. 4
1.1 Terminology ................................................ 5
1.2 Transaction Definition Template ............................ 7
2 Semantics Specification ...................................... 8
2.1 General Protocol Design .................................... 8
2.1.1 Protocol Transactions .................................... 8
2.1.2 Message Types ............................................ 9
2.1.3 Session, Policy Rule, and Policy Rule Group .............. 10
2.1.4 Atomicity ................................................ 10
2.1.5 Access Control ........................................... 11
2.1.6 Middlebox Capabilities ................................... 11
2.1.7 Agent and Middlebox Identifiers .......................... 12
2.1.8 Conformance .............................................. 12
2.2 Session Control Transactions ............................... 13
2.2.1 Session Establishment (SE) ............................... 13
2.2.2 Session Termination (ST) ................................. 15
2.2.3 Asynchronous Session Termination (AST) ................... 16
2.2.4 Session Termination by Interruption of Connection ........ 17
2.2.5 Session State Machine .................................... 17
2.3 Policy Rule Transactions ................................... 18
2.3.1 Configuration Transactions ............................... 18
2.3.2 Establishing Policy Rules ................................ 18
2.3.3 Maintaining Policy Rules and Policy Rule Groups .......... 19
2.3.4 Policy Events and Asynchronous Notifications ............. 20
2.3.5 Address Tuples ........................................... 21
2.3.6 Address Parameter Constraints ............................ 22
2.3.7 Interface specific Policy Rules .......................... 24
2.3.8 Policy Reserve Rule (PRR) ................................ 25
2.3.9 Policy Enable Rule (PER) ................................. 29
2.3.10 Policy Rule Lifetime Change (RLC) ....................... 35
2.3.11 Policy Rule List (PRL) .................................. 36
2.3.12 Policy Rule Status (PRS) ................................ 37
2.3.13 Asynchronous Policy Rule Event (ARE) .................... 39
2.3.14 Policy Rule State Machine ............................... 40
2.4 Policy Rule Group Transactions ............................. 41
2.4.1 Overview ................................................. 41
2.4.2 Group Lifetime Change (GLC) .............................. 42
2.4.3 Group List (GL) .......................................... 44
2.4.4 Group Status (GS) ........................................ 45
3 Conformance Statements ....................................... 46
3.1 General Implementation Conformance ......................... 47
3.2 Middlebox Conformance ...................................... 47
3.3 Agent Conformance .......................................... 48
4 Transaction Usage Examples ................................... 48
4.1 Exploring Policy Rules and Policy Rule Groups .............. 48
4.2 Enabling a SIP-Signaled Call ............................... 52
5 Compliance with MIDCOM Requirements .......................... 57
5.1 Protocol Machinery Requirements ............................ 57
Stiemerling, Quittek, Taylor [Page 2]
Internet-Draft MIDCOM Protocol Semantics January 2004
5.1.1 Authorized Association ................................... 57
5.1.2 Agent connects to Multiple Middleboxes ................... 57
5.1.3 Multiple Agents connect to same Middlebox ................ 58
5.1.4 Deterministic Behavior ................................... 58
5.1.5 Known and Stable State ................................... 58
5.1.6 Status Report ............................................ 59
5.1.7 Unsolicited Messages (Asynchronous Notifications) ........ 59
5.1.8 Mutual Authentication .................................... 59
5.1.9 Session Termination by any Party ......................... 59
5.1.10 Request Result .......................................... 59
5.1.11 Version Interworking .................................... 60
5.1.12 Deterministic Handling of Overlapping Rules ............. 60
5.2 Protocol Semantics Requirements ............................ 60
5.2.1 Extensible Syntax and Semantics .......................... 60
5.2.2 Policy Rules for Different Types of Middleboxes .......... 60
5.2.3 Ruleset Groups ........................................... 60
5.2.4 Policy Rule Lifetime Extension ........................... 61
5.2.5 Robust Failure Modes ..................................... 61
5.2.6 Failure Reasons .......................................... 61
5.2.7 Multiple Agents Manipulating Same Policy Rule ............ 61
5.2.8 Carrying Filtering Rules ................................. 61
5.2.9 Parity of Port Numbers ................................... 61
5.2.10 Consecutive Range of Port Numbers ....................... 62
5.2.11 Contradicting Overlapping Policy Rules .................. 62
5.3 Security Requirements ...................................... 62
5.3.1 Authentication, Confidentiality, Integrity ............... 62
5.3.2 Optional Confidentiality of Control Messages ............. 62
5.3.3 Operation across Un-trusted Domains ...................... 62
5.3.4 Mitigate Replay Attacks .................................. 62
6 Security Considerations ...................................... 63
7 IAB Considerations on UNSAF .................................. 63
8 Acknowledgments .............................................. 64
9 Normative References ......................................... 65
10 Informative References ...................................... 65
11 Authors' Addresses .......................................... 65
12 Full Copyright Statement .................................... 66
Stiemerling, Quittek, Taylor [Page 3]
Internet-Draft MIDCOM Protocol Semantics January 2004
1. Introduction
The MIDCOM working group has defined a framework [MDC-FRM] for the
middlebox communication and a list of requirements [MDC-REQ]. The
next step towards a MIDCOM protocol is the specification of protocol
semantics that are constrained, but not completely implied by the
documents mentioned above.
This memo suggests a semantics for the MIDCOM protocol. It is fully
compliant with the requirements listed in [MDC-REQ] and with the
working group's consensus on semantic issues.
In conformance with the working group charter, the semantics
description is targeted at packet filters and network address
translators (NATs) and it supports applications that require dynamic
configuration of these middleboxes.
The semantics are defined in terms of transactions. Two basic types
of transactions are used: request-reply transactions and asynchronous
transactions. For each transaction the semantics is specified by
describing (1) the parameters of the transaction, (2) the processing
of request messages at the middlebox, and (3) the state transitions
at the middlebox caused by the request transactions or indicated by
the asynchronous transactions, respectively, and the (4) reply and
notification messages sent from the middlebox to the agent in order
to inform the agent about the state change.
The semantics can be implemented by any protocol that supports these
two transaction types and that is sufficiently flexible concerning
transaction parameters. Different implementations for different
protocols might need to extend the semantics described below by
adding further transactions and/or adding further parameters to
transactions and/or splitting single transactions into a set of
transactions. Regardless of such extensions, the semantics below
provide a minimum necessary subset of what must be implemented.
The remainder of this document is structured as follows. Section 2
describes the protocol semantics. It is structured in four
subsections:
- General Protocol Issues (Section 2.1)
- Session Control (Section 2.2)
- Policy Rules (Section 2.3)
- Policy Rule Groups (Section 2.4)
Section 3 contains conformance statements for MIDCOM protocol
definitions and MIDCOM protocol implementations with respect to the
semantics defined in Section 2. Section 4 gives two elaborated usage
examples. Finally, Section 5 explains how the semantics meets the
MIDCOM requirements.
Stiemerling, Quittek, Taylor [Page 4]
Internet-Draft MIDCOM Protocol Semantics January 2004
1.1. Terminology
The terminology in this memo follows the definitions given in the
framework [MDC-FRM] and requirements [MDC-REQ] document.
In addition the following terms are used:
request transaction A request transaction consists of a
request message transfer from the agent to
the middlebox, processing of the message
at the middlebox, a reply message transfer
from the middlebox to the agent, and the
optional transfer of notification messages
from the middlebox to other agents than
the one requesting the transaction. A
request transaction might cause a state
transition at the middlebox.
configuration transaction A configuration transaction is a request
transaction containing a request for state
change in the middlebox. If accepted, it
causes a state change at the middlebox.
monitoring transaction A monitoring transaction is a request
transaction containing a request for state
information from the middlebox. It does
not cause a state transition at the
middlebox.
asynchronous transaction An asynchronous transaction is not
triggered by an agent. It may occur
without any agent participating in a
session with the middlebox. Potentially,
an asynchronous transaction includes the
transfer of notification messages from the
middlebox to agents that participate in an
open session. A notification message is
sent to each agent that need to be
notified about the asynchronous event.
The message indicates the state transition
at the middlebox.
agent unique An agent unique value is unique in the
context of the agent. This context
includes all MIDCOM sessions the agent
participates in. An agent unique value is
assigned by the agent.
middlebox unique A middlebox unique value is unique in the
context of the middlebox. This context
Stiemerling, Quittek, Taylor [Page 5]
Internet-Draft MIDCOM Protocol Semantics January 2004
includes all MIDCOM sessions the middlebox
participates in. A middlebox unique value
is assigned by the middlebox.
policy rule In general, a policy rule is "a basic
building block of a policy-based system.
It is the binding of a set of actions to a
set of conditions - where the conditions
are evaluated to determine whether the
actions are performed." [RFC3198]. In
the MIDCOM context the condition is a
specification of a set of packets to which
rules are applied. The set of actions
always contains just a single element per
rule, either action "reserve" or action
"enable".
policy reserve rule A policy rule containing a reserve action.
The policy condition of this rule is
always true. The action is the
reservation of just an IP address or a
combination of an IP address and a range
of port numbers on neither, one, or both
sides of the middlebox, depending on the
middlebox configuration.
policy enable rule A policy rule containing an enable action.
The policy condition consists of a
descriptor of one or more unidirectional
or bidirectional packet flows, and the
policy action enables packets belonging to
this flow to traverse the middlebox. The
descriptor identifies the protocol, the
flow direction, the source and destination
addresses, optionally with a range of port
numbers.
NAT binding The term NAT binding used in this document
is not necessarily refering to a NAT bind
as defined in [NAT-TERM]. A NAT binding
in the MIDCOM semantics refers to an
abstraction that enables communcation
between two end points through the NAT-
type middlebox. An enable action may
result in a NAT bind or a NAT session,
depending on the request and its
parameters.
Stiemerling, Quittek, Taylor [Page 6]
Internet-Draft MIDCOM Protocol Semantics January 2004
1.2. Transaction Definition Template
In the following sections, semantics of the MIDCOM protocol is
specified per transaction. A transaction specification contains the
following entries. Parameter entries, failure reason and notification
message type are only specified if applicable.
transaction-name
A description name for this type of transaction.
transaction-type
The transaction type is either 'configuration', 'monitoring', or
'asynchronous'. See Section 1.1. for a description of
transaction types.
transaction-compliance
This entry contains either 'mandatory' or 'optional'. For details
see Section 2.1.8.
request-parameters
This entry lists all parameters that are necessary for this
request. A description for each parameter is given.
reply-parameters (success)
This entry lists all parameters that are sent back from the
middlebox to the agent as positive response to the prior request.
A description for each parameter is given.
failure reason
All negative replies do have two parameters, a request identifier
identifying the request on which the reply is sent and a parameter
indicating the failure reason. Since these parameters are
compulsory, they are not listed in the template. But the template
contains a list of potential failure reasons that may be indicated
by the second parameter. The list is not exhaustive. A concrete
protocol specification may extend the list.
notification message type
The type of the notification message type that may be used by this
transaction.
semantics
This entry describes the actual semantics of the transaction.
Particularly, it describes the processing of the request message
by the middlebox, and middlebox state transitions caused by or
causing the transaction, respectively.
Stiemerling, Quittek, Taylor [Page 7]
Internet-Draft MIDCOM Protocol Semantics January 2004
2. Semantics Specification
2.1. General Protocol Design
The semantics specification aims at a balance between proper support
of applications that require dynamic configuration of middleboxes and
simplicity of specification and implementation of the protocol.
Protocol interactions are structured into transactions. State of
middleboxes is described by state machines. The state machines are
defined by states and state transitions. A single transaction may
cause or be caused by state transitions in more than one state
machine, but per state machine there is no more than one transition
per transaction.
2.1.1. Protocol Transactions
State transitions are either initiated by a request message from the
agent to the middlebox, or they are initiated by some other event at
the middlebox. In the first case, the middlebox informs the agent by
sending a reply message on the actual state transition, in latter
case the middlebox sends an unsolicited asynchronous notification
message to each agent that is affected by the transaction (if it
participates in an open session with the middlebox).
Request and reply messages contain an agent unique request identifier
that allows the agent to determine to which sent request a received
reply corresponds.
An analysis of the requirements showed that four kinds of
transactions are required:
- configuration transactions allowing the agent to request state
transitions at the middlebox
- asynchronous transactions allowing the middlebox to change state
without a request by an agent.
- monitoring transaction allowing the agent to request state
information from the middlebox
- convenience transactions combining a set of configuration
transactions
Configuration transactions and asynchronous transactions provide the
basic MIDCOM protocol functionality. They are related to middlebox
state transitions and they concern establishment and termination of
MIDCOM sessions and of policy rules.
Stiemerling, Quittek, Taylor [Page 8]
Internet-Draft MIDCOM Protocol Semantics January 2004
Monitoring transactions are not related to middlebox state
transitions. They are used by agents for exploring number, status
and properties of policy rules established at the middlebox.
Convenience transactions simplify MIDCOM sessions by combining a set
of configuration transactions into a single one. They are not
necessary for MIDCOM protocol operation.
As specified in detail in Section 3, configuration transactions and
asynchronous transactions are mandatory. They must be implemented by
a compliant middlebox. All convenience transactions are optional and
some of the monitoring transactions are optional.
2.1.2. Message Types
The MIDCOM protocol supports three kinds of messages: request
messages, reply messages and notification messages. For each kind,
there exist different message types. In this semantics document,
message types are only defined by the list of parameters. The order
of the parameters and their encoding is left to a concrete protocol
definition. A protocol definition may also add further parameters to
a message type or combine several parameters into one, as long as the
information contained in the parameters defined in the semantics is
still contained.
For request messages and positive reply messages there exists one
message type per request transaction. Each reply transaction defines
the parameter list of the request message and of the positive
(successful) reply message using the transaction definition template
that is defined in Section 1.2.
In case of a failed request transaction, a negative reply message is
sent from the middlebox to the agent. This message has the same type
for all request transactions. It contains the request identifier
identifying the request on which the reply is sent and a parameter
indicating the failure reason.
For notification messages, there exist three message types: the
Session Termination Notification (STN) message type, the Policy Rule
Event Notification (REN) message type and the Group Event
Notification (GEN) message type. All of them contain a middlebox-
unique notification identifier.
STN The Session Termination Notification message additionally
contains a single parameter indicating the reason of session
termination by the middlebox.
PEN The Policy Rule Event Notification message contains the
notification identifier, a policy rule identifier and the
Stiemerling, Quittek, Taylor [Page 9]
Internet-Draft MIDCOM Protocol Semantics January 2004
remaining policy lifetime.
GEN The Group Event Notification message contains the notification
identifier, a policy rule group identifier and the remaining
policy rule group lifetime.
2.1.3. Session, Policy Rule, and Policy Rule Group
All transactions can further be grouped into transactions concerning
sessions, transactions concerning policy rules, and transactions
concerning policy rule groups. Policy rule groups can be used to
indicate relationships between policy rules and to simplify
transactions on a set of policy rules by using a single transaction
per group instead of one per policy rule.
Sessions and policy rules at the middlebox are stateful. Their
states are independent of each other and their state machines (one
per session and one per policy rule) can be separated. Policy rule
groups are also stateful, but the middlebox does not need to maintain
state for policy rule groups, because the semantics were chosen such
that the policy rule group state is implicitly defined by the state
of all policy rules belonging to the group (see Section 2.4).
The separation of session state and policy rule state simplifies the
specification of the semantics as well as a protocol implementation.
Therefore, the semantics specification is structured accordingly and
we use two separated state machines to illustrate the semantics.
Please note, that state machines of concrete protocol designs and
implementations will most probably be more complex than the state
machines presented here. However, the protocol state machines are
expected to be a superset of the semantics state machines in this
document.
2.1.4. Atomicity
All request transactions are atomic with respect to each other. This
means that processing of a request at the middlebox is never
interrupted by another arriving or already queued request. This
particularly applies when the middlebox concurrently receives
requests originating in different sessions. However, asynchronous
transactions may interrupt and/or terminate processing of a request
at any time.
All request transactions are atomic from the point of view of the
agent. Processing of a request does not start before the complete
request arrives at the middlebox. No intermediate state is stable at
the middlebox and no intermediate state is reported to any agent.
Stiemerling, Quittek, Taylor [Page 10]
Internet-Draft MIDCOM Protocol Semantics January 2004
The number of transactions specified in this document is rather
small. Again for simplicity we reduced it close to a minimal set
that still meets the requirements. For a real implementation of the
protocol, it might be required to split some of the transactions
specified below into two or more transactions of the respective
protocol. Reasons for this might be constraints of the particular
protocol or the desire for more flexibility. In general this should
not be a problem. However, it should be considered that this might
change atomicity of the affected transactions.
2.1.5. Access Control
Access to policy rules and policy rule groups is based on ownership.
When a policy rule is created, a middlebox unique identifier is
generated for identifying it in further transactions. Beyond the
identifier, each policy rule has an owner. The owner is the
authenticated agent that established the policy rule. The middlebox
uses the owner attribute of a policy rule for controlling access to
it: each time an authenticated agent requests to modify an existing
policy rule, the middlebox determines the owner of the policy rule
and checks if the requesting agent is authorized to perform
transactions on the owning agent's policy rules.
All policy rules belonging to the same policy rule group must have
the same owner. Therefore, authenticated agents either have access
to all members of a policy rule group, or to none of them.
The middlebox may be configured to allow specific authenticated
agents to access and modify policy rules with certain specific
owners. Certainly, a reasonable default configuration would be that
each agent can access its own policy rules. Also, it might be a good
idea, to have an agent identity configured to act as administrator
being allowed to modify all policy rules owned by any agent. Anyway,
the configuration of authorization at the middlebox is out of scope
of the MIDCOM semantics and protocol.
2.1.6. Middlebox Capabilities
For several reasons it is useful that the agent learns at session
establishment about particular capabilities of the middlebox.
Therefore, the session establishment procedure described in Section
2.2.1 includes a transfer of capability information from the
middlebox to the agent. The list of covered middlebox capabilities
includes
- type of the middlebox
for example: FW, NAT, NAPT, NAT-PT, twice-NAT or combination
of those
- internal IP address wildcard support
Stiemerling, Quittek, Taylor [Page 11]
Internet-Draft MIDCOM Protocol Semantics January 2004
- external IP address wildcard support
- port wildcard support
- supported IP version(s) for internal network:
IPv4, IPv6, or both
- supported IP version(s) for external network:
IPv4, IPv6, or both
- list of supported optional MIDCOM protocol transactions
- optional interface specific policy rule support: not
supported or supported.
- policy rule persistency: persistent or non-persistent
A rule is persistent when the middlebox can save the rule to
a non-volatile memory, e.g. a hard disk or flash memory.
- maximum remaining lifetime of a policy rule or policy rule
group
- idle-timeout of policy rules in the middlebox
Reserved and enabled policy rules that are not used by any
data traffic for the time of this idle-timeout are deleted
automatically by the middlebox. For the deletion of policy
rules by middleboxes see Section 2.3.13 about Asynchronous
Policy Rule Event (ARE).
- maximum number of simultaneous MIDCOM sessions
The list of middlebox capabilities may be extended by a concrete
protocol specification by further information that is useful for the
agent.
2.1.7. Agent and Middlebox Identifiers
In order to allow both agents and middleboxes to maintain multiple
sessions each request message contains a parameter identifying the
requesting agent, and each reply message and each notification
message contains a parameter identifying the middlebox. These
parameters are not explicitly listed in the description of the
individual transactions, because they are common to all of them and
not further referred to in the individual semantics descriptions.
Also, they are not necessarily passed explicitly as parameters of the
MIDCOM protocol, but they might be provided by the used underlying
(secure) transport protocol. Agent identifiers at the middlebox are
middlebox unique and middlebox identifiers at the agent are agent
unique respectively.
2.1.8. Conformance
The MIDCOM requirements in [MDC-REQ] demand certain capabilities of
the MIDCOM protocol, which are met by the set of transactions
specified below. However, an actual implementation of a middlebox
may support only a subset of these transactions. The set of
announced supported transactions may be different for different
Stiemerling, Quittek, Taylor [Page 12]
Internet-Draft MIDCOM Protocol Semantics January 2004
authenticated agents. At session establishment, the middlebox
informs the authenticated agent by capability exchange, which
transactions the agent is authorized to perform. Some transactions
need to be offered to every authenticated agent.
Each transaction definition below has a conformance entry which
contains either 'mandatory' or 'optional'. A mandatory transaction
needs to be implemented by every middlebox offering MIDCOM service
and must be must be offered to each of the authenticated agents. An
optional transaction does not necessarily need to be implemented by a
middlebox. If an optional transactions is implemented in the
middlebox, the middlebox may offer these optional transactions only
to certain authenticated agents. The middlebox may offer one,
several, all, or no optional transactions to the agents. Whether or
not an agent is allowed to use an optional request transaction is
determined by the middlebox's authorization procedure which is not
further specified by this document.
2.2. Session Control Transactions
Before any transaction on policy rules or policy rule groups is
possible, a valid MIDCOM session must be established. A MIDCOM
session is an authenticated and authorized association between agent
and middlebox. Sessions are initiated by agents and can be
terminated by either the agent or the middlebox. Both agent and
middlebox may participate in several sessions (with different
entities) at the same time. For distinguishing different sessions
each party uses local session identifiers.
All transactions are transmitted within this MIDCOM session.
Session control is supported by three transactions:
- Session Establishment (SE)
- Session Termination (ST)
- Asynchronous Session Termination (AST)
The first two are configuration transactions initiated by the agent,
the last one is a asynchronous transaction initiated by the
middlebox.
2.2.1. Session Establishment (SE)
transaction-name: session establishment
transaction-type: configuration
transaction-compliance: mandatory
Stiemerling, Quittek, Taylor [Page 13]
Internet-Draft MIDCOM Protocol Semantics January 2004
request-parameters:
- request identifier: an agent unique identifier for matching
corresponding request and reply at the agent.
- version: the version of the MIDCOM protocol
- middlebox authentication challenge (mc): an authentication
challenge token for authentication of the middlebox. As seen
below, this is present only in the first iteration of the
request.
- agent authentication (aa): an authentication token to
authenticate the agent to the middlebox. As seen below, this is
updated in the second iteration of the request with material
responding to the middlebox challenge.
reply-parameters (success):
- request identifier: an identifier matching the identifier
request.
- middlebox authentication (ma): an authentication token to
authenticate the middlebox to the agent.
- agent challenge token (ac): an authentication challenge token for
the agent authentication.
- middlebox capabilities: a list describing the middlebox's
capabilities. See Section 2.1.6. for the list of middlebox
capabilities.
failure reason:
- authentication failed
- no authorization
- protocol version of agent and middlebox do not match
- lack of resources
semantics:
This session establishment transaction is used to establish a
MIDCOM session. For mutual authentication of both parties two
subsequent session establishment transactions are required as
shown in Figure 1.
Stiemerling, Quittek, Taylor [Page 14]
Internet-Draft MIDCOM Protocol Semantics January 2004
agent middlebox
| session establishment request |
| (with middlebox challenge mc) | CLOSED
|-------------------------------------------->|
| |
| successful reply (with middlebox |
| authentication ma and agent challenge ac) |
|<--------------------------------------------|
| | NOAUTH
| session establishment request |
| (with agent authentication aa) |
|-------------------------------------------->|
| |
| successful reply |
|<--------------------------------------------|
| | OPEN
| |
Figure 1: Mutual authentication of agent and middlebox
Session establishment may be simplified by using only a single
transaction. In this case server challenge and agent challenge
are omitted by the sender or ignored by the receiver, and
authentication must be provided by other means, for example by TLS
[RFC2246] or IPSEC [RFC2402][RFC2406].
The middlebox checks with its policy decision point if the
requesting agent is authorized to open a MIDCOM session. If not a
negative reply with 'no authorization' as failure reason is
generated by the middlebox. If authentication and authorization
are successful, the session is established and the agent may start
with requesting transactions on policy rules and policy rule
groups.
Part of the successful reply is an indication of the middlebox's
capabilities.
2.2.2. Session Termination (ST)
transaction-name: session termination
transaction-type: configuration
transaction-compliance: mandatory
request-parameters:
- request identifier: an agent unique identifier for matching
corresponding request and reply at the agent.
Stiemerling, Quittek, Taylor [Page 15]
Internet-Draft MIDCOM Protocol Semantics January 2004
reply-parameters (success only):
- request identifier: an identifier matching the identifier of the
request.
semantics:
This transaction is used to close the MIDCOM session on behalf of
the agent. After session termination the middlebox keeps all
established policy rules until their lifetime expires or until an
event occurs which causes the middlebox to terminate them.
The middlebox always generates a successful reply. After sending
the reply, the middlebox will not send any further messages to the
agent within the current session. It also will not process any
further request within this session, which it has received while
it was processing the session termination request, or which it
receives later.
2.2.3. Asynchronous Session Termination (AST)
transaction-name: asynchronous session termination
transaction-type: asynchronous
transaction-compliance: mandatory
notification message type: Session Termination Notification (STN)
reply-parameters (success only):
- termination reason: the reason why the session is terminated.
semantics:
The middlebox may decide at any point in time to terminate a
MIDCOM session. Before terminating the actual session the
middlebox generates a STN message and sends it to the agent. After
sending the notification, the middlebox will not process any
further request by the agent, even if it is already queued at the
middlebox.
After session termination the middlebox keeps all established
policy rules until their lifetime expires or until an event occurs
on which the middlebox terminates them.
Different to other asynchronous transactions, no more than one
notification is sent, because there is only one agent affected by
the transaction.
Stiemerling, Quittek, Taylor [Page 16]
Internet-Draft MIDCOM Protocol Semantics January 2004
2.2.4. Session Termination by Interruption of Connection
If a MIDCOM session is based on an underlying network connection,
then the session can also be terminated by an interruption of this
connection. If the middlebox detects this, it immediately terminates
the session. The effect on established policy rules is the same as
for the Asynchronous Session Termination.
2.2.5. Session State Machine
A state machine illustrating the semantics of the session
transactions is shown in Figure 2. The used transaction
abbreviations can be found in the headings of the particular
transaction section.
All sessions start in state CLOSED. A successful SE transaction can
cause a state transition to state OPEN, if mutual authentication is
already provided by other means. Otherwise, it causes a transition
to state NOAUTH. From this state a failed second SE transaction
returns to state CLOSED. A successful SE transaction causes a
transition to state OPEN. At any time an AST transaction or a
connection failure may occur causing a transition to state CLOSED. A
successful ST transaction from either NOAUTH or OPEN also causes a
return to CLOSED. The parameters of the transactions are explained
in Figure 2, the value mc=0 represents an empty middlebox challenge.
mc = middlebox challenge
SE/failure ma = middlebox authentication
+-------+ ac = agent challenge
| v aa = agent authentication
+----------+
| CLOSED |----------------+
+----------+ | SE(mc!=0)/
| ^ ^ | success(ma,ac)
SE(mc=0, | | | AST |
aa=OK)/ | | | SE/failure v
success | | | ST/success +----------+
| | +------------| NOAUTH |
| | +----------+
| | AST | SE(mc=0,
v | ST/success | aa=OK)/
+----------+ | success
| OPEN |<---------------+
+----------+
Figure 2: Session State Machine
Stiemerling, Quittek, Taylor [Page 17]
Internet-Draft MIDCOM Protocol Semantics January 2004
2.3. Policy Rule Transactions
This section describes the semantics for transactions on policy
rules. The following transactions are specified:
- Policy Reserve Rule (PRR)
- Policy Enable Rule (PER)
- Policy Rule Lifetime Change (RLC)
- Policy Rule List (PRL)
- Policy Rule Status (PRS)
- Asynchronous Policy Rule Event (ARE)
The first three transactions (PRR, PER, RLC) are configuration
transactions initiated by the agent. The fourth and fifth (PRL, PRS)
are a monitoring transactions. And the last one (ARE) is a
asynchronous transaction. The PRL and PRS and transactions do not
have any effect on the policy rule state machine.
Before any transaction can start, a valid MIDCOM session must be
established.
2.3.1. Configuration Transactions
Policy Rule transactions PER and RLC constitute the core of the
MIDCOM protocol. Both are mandatory and they serve for
- configuring NAT bindings (PER)
- configuring firewall pinholes (PER)
- extending the lifetime of established policy rules (RLC)
- deleting policy rules (RLC)
In some cases it is required to know in advance which IP address (and
port number) would be chosen by NAT in a PER transaction. This
information is required before sufficient information for performing
a complete PER transaction is available (see example in Section 4.2).
For supporting such cases, the core transactions are extended by the
Policy Reserve Rule (PRR) transaction serving for
- reserving addresses and port numbers at NATs (PRR)
2.3.2. Establishing Policy Rules
Both PRR and PER establish a policy rule. The action within the rule
is 'reserve' if set by PRR and 'enable' if set by PER.
The Policy Reserve Rule (PRR) transaction is used to establish an
address reservation on neither, one, or both sides of the middlebox,
depending on the middlebox configuration. The transaction returns
Stiemerling, Quittek, Taylor [Page 18]
Internet-Draft MIDCOM Protocol Semantics January 2004
the reserved IP addresses and the optional ranges of port numbers to
the agent. No address binding or pinhole configuration is performed
at the middlebox. Packet processing at the middlebox remains
unchanged.
On pure firewalls, the PRR transaction is successfully processed
without any reservation, but the state transition of the MIDCOM
protocol engine is exactly the same as on NATs.
On a traditional NAT (see [NAT-TRAD]), only an external address is
reserved; on a twice-NAT, an internal and an external address is
reserved. The reservation at a NAT is the reservation of the
required resources ,like IP addresses and port numbers, for future
use. How the reservation is exactly done depends on the
implementation of the NAT. In both cases the reservation concerns
either an IP address only or a combination of an IP address with a
range of port numbers.
The Policy Enable Rule (PER) transaction is used to establish a
policy rule that has an effect on packet processing at the middlebox.
Depending on its input parameters, it may make use of the reservation
established by a PRR transaction, or create a new rule from scratch.
On a NAT, the enable action is interpreted as bind action
establishing bindings between internal and external addresses. At a
firewall, the enable action is interpreted as one or more allow
actions configuring pinholes. The number of allow actions depends on
the parameters of the request and the implementation of the firewall.
On a combined NAT/firewall, the enable action is interpreted as a
combination of bind and allow actions.
The PRR transaction and the PER transaction are described in more
detail in Sections 2.3.8. and 2.3.9. below.
2.3.3. Maintaining Policy Rules and Policy Rule Groups
Each policy rule has a middlebox unique identifier.
Each policy rule has an owner. Access control to the policy rule is
based on ownership (see section 2.1.5). Ownership of a policy rule
does not change during lifetime of the policy rule.
Each policy rule has its individual lifetime. If the policy rule
lifetime expires, the policy rule will be terminated at the
middlebox. Typically, the middlebox indicates termination of a
policy rule by an ARE transaction. A policy rule lifetime change
(RLC) transaction may extend the lifetime of the policy rule up to
the limit specified by the middlebox at session setup. Also a RLC
Stiemerling, Quittek, Taylor [Page 19]
Internet-Draft MIDCOM Protocol Semantics January 2004
transaction may be used for shortening a policy rule's lifetime or
deleting a policy rule by requesting a lifetime of zero. (Please
note that policy rule lifetimes may also be modified by the group
lifetime change (GLC) transaction).
Each policy rule is member of exactly one policy rule group. Group
membership does not change during the lifetime of a policy rule.
Selecting the group is part of the transaction establishing the
policy rule. This transaction implicitly creates a new group if the
agent does not specify one. The new group identifier is chosen by
the middlebox. New members are added to a group, if the agent's
request designates an already existing group. A group only exists as
long as it has member policy rules. As soon as all policies
belonging to the group reach the end of their lifetimes, the group
does not exist anymore.
Agents can explore the properties and status of all policy rules they
are allowed to access by using the Policy Rule Status (PRS)
transaction.
2.3.4. Policy Events and Asynchronous Notifications
If a policy rule changes its state or if a policy rule's remaining
lifetime is changed in another way than being decreased by time, then
all agents that can access this policy rule and that participate in
an open session with the middlebox are notified by the middlebox. If
the state or lifetime change was requested explicitly by a request
message, then the middlebox notifies the agent by returning the
corresponding reply. All other agents that can access the policy are
notified by an Policy Rule Event Notification (REN) message.
Please note that a middlebox can serve multiple agents at the same
time in different parallel sessions. Between these agents, the sets
of policy rules that can be accessed by them may overlap. For
example, there might be an agent that authenticates as administrator
and can access all policies of all agents. Or there is a backup
agent running a session in parallel to a main agent and
authenticating itself as the same entity as the main agent.
In case of a PER, PRR, or RLC transaction, the requesting agent
receives a PER, PRR, or RLC reply, respectively. To all other agents
that can access the created, modified, or terminated policy rule (and
that participate in an open session with the middlebox) the middlebox
sends a REN message carrying the policy rule identifier (PID) and the
remaining lifetime of the policy rule.
In case of a rule termination by lifetime extension or other events
not triggered by an agent, then the middlebox sends a REN message to
each agents that can access the particular policy rule and that
Stiemerling, Quittek, Taylor [Page 20]
Internet-Draft MIDCOM Protocol Semantics January 2004
participates in an open session with the middlebox. This ensures
that an agent always knows the most recent state of all policy rules
it can access.
2.3.5. Address Tuples
Request and reply messages of the PRR, PER, and PRS transactions
contain address specifications for IP and transport addresses. These
parameters include
- IP version
- IP address
- IP address prefix length
- transport protocol
- port number
- port parity
- port range
Additionally the request message of PER and reply message of PRS
contains a direction of flow parameter. This direction of flow
parameter indicates for UDP and IP the direction of packets
traversing the middlebox. For 'inbound' the UDP packets are
traversing from outside to inside, for 'outbound' the UDP packets are
traversing from inside to the outside. In both cases of 'inbound'
and 'outbound' the packets can traverse the middelbox only uni-
directional. A bi-directional flow is enabled through 'bi-
directional' as direction of flow parameter. In the case of TCP the
packet flow is always bi-directional, but the direction of flow
parameter is defined as:
- inbound: bi-directional TCP packet flow. First packet, with TCP
SYN flag set, must arrive at the middlebox at the outside
interface.
- outbound: bi-directional TCP packet flow. First packet, with TCP
SYN flag set, must arrive at the middlebox at the inside
interface.
- bi-directional: bi-directional TCP packet flow. First packet,
with TCP SYN flag set, may arrive at inside or outside interface.
We refer to the set of these parameters as an address tuple. An
address tuple specifies either a communication endpoint at an
internal or external device or allocated addresses at the middlebox.
In this document, we distinguish four kinds of address tuples as
shown in Figure 3.
Stiemerling, Quittek, Taylor [Page 21]
Internet-Draft MIDCOM Protocol Semantics January 2004
+----------+ +----------+
| internal | A0 A1 +-----------+ A2 A3 | external |
| endpoint +----------+ middlebox +----------+ endpoint |
+----------+ +-----------+ +----------+
Figure 3: Address tuples A0 - A3
- A0 - internal endpoint: address tuple A0 specifies a
communication endpoint of a device within the - with respect to
the middlebox - internal network.
- A1 - middlebox inside address: address tuple A1 specifies a
virtual communication endpoint at the middlebox within the
internal network. A1 is the destination address for packets
passing from the internal endpoint to the middlebox, and is the
source for packets passing from the middlebox to the internal
endpoint.
- A2 - middlebox outside address: address tuple A2 specifies a
virtual communication endpoint at the middlebox within the
external network. A2 is the destination address for packets
passing from the external endpoint to the middlebox, and is the
source for packets passing from the middlebox to the external
endpoint.
- A3 - external endpoint: address tuple A3 specifies a
communication endpoint of a devices within the - with respect to
the middlebox - external network.
For a firewall, the inside and outside endpoints are identical to the
corresponding external or internal endpoints, respectively. In this
case the installed policy rule sets the same value in A2 as in A0
(A0=A2), and sets the same value in A1 as in A3 (A1=A3).
For a traditional NAT, A2 is given a value different from that of A0,
but the NAT binds them. As for the firewall, so at a traditional NAT:
A1 has the same value as A3.
For a twice-NAT there are two bindings of address tuples: A1 and A2
are both assigned values by the NAT. The middlebox outside address
A2 is bound to the internal endpoint A0 and the middlebox inside
address A1 is bound to the external endpoint A3.
2.3.6. Address Parameter Constraints
For transaction parameters belonging to an address tuple some
constraints exist which are common for all messages using them.
Therefore, these constraints are summarized in the following and not
Stiemerling, Quittek, Taylor [Page 22]
Internet-Draft MIDCOM Protocol Semantics January 2004
repeated again when describing the parameters in the transaction
descriptions.
The MIDCOM semantics defined in this document specifies the handling
of IPv4 and IPv6 as network protocols, and of TCP and UDP (over IPv4
and IPv6) as transport protocols. The handling of any other
transport protocol, e.g. SCTP, is not defined within the semantics
and may be added in future versions.
The IP version parameter has either the value 'IPv4' or 'IPv6'. In a
policy rule, the value of the IP version parameter must be the same
for address tuples A0 and A1, and it must be the same for A2 and A3.
The value of the IP address parameter must conform with the specified
IP version.
The IP address of an address tuple may be wildcarded. Whether IP
address wildcarding is allowed or in which range it is allowed
depends on the local policy of the middlebox, see also section 6
"Security Considerations". Wildcarding is specified by the IP
address prefix length parameter of an address tuple. In line with
the common use of a prefix length, this parameter indicates the
number of high significant bits of the IP address that are fixed,
while the remaining low significant bits of the IP address are
wildcarded.
The value of the transport protocol parameter can be either 'TCP',
'UDP', or 'ANY'. If the transport protocol parameter has the value
'ANY', only IP headers are considered for packet handling in the
middlebox, i.e. the transport header is not considered. The values
of the parameters port number, port range and port parity are
irrelevant if the protocol parameter is 'ANY'. In a policy rule the
value of the transport protocol parameter must be the same for all
address tuples A0, A1, A2, and A3.
The value of the port number parameter is either zero or a positive
integer. A positive integer specifies a concrete UDP or TCP port
number. The value zero specifies port wildcarding for the protocol
specified by the transport protocol parameter. If the port number
parameter has the value zero, then the value of the port range
parameter is irrelevant. Depending on the value of the transport
protocol parameter, this parameter may truly refer to ports, or may
refer to an equivalent concept.
The port parity parameter is differently used in the context of
policy reserve rules (PRR) and policy enable rules (PER). In the
context of a PRR, the value of the parameter may be 'odd', 'even', or
'any'. It specifies the parity of the first (lowest) reserved port
number.
Stiemerling, Quittek, Taylor [Page 23]
Internet-Draft MIDCOM Protocol Semantics January 2004
In the context of a PER, the port parity parameter indicates to the
middlebox, whether or not port numbers allocated at the middlebox
should have the same parity as the corresponding internal or external
port numbers, respectively. In this context, the parameter has
either the value 'same' or 'any'. If it has the value 'same', then
the parity of the port number of A0 must be the same as the parity of
the port number of A2, and the parity of the port number of A1 must
be the same as the parity of the port number of A3. If the port
parity parameter has the value 'any', then there are no constraints
on the parity of any port number.
The port range parameter specifies a number of consecutive port
numbers. Its value is a positive integer. Together with the port
number parameter this parameter defines a set of consecutive port
numbers starting with the port number specified by the port number
parameter as the lowest port number and having as many elements as
specified by the port range parameter. A value of one specifies just
a single port number. The port range parameter must have the same
value for each address tuple A0, A1, A2, and A3.
A single policy rule P containing a port range value greater than one
is equivalent to a set of policy rules containing a number n of
policies P_1, P_2, ..., P_n that equals the value of the port range
parameter. All policy rules P_1, P_2, ..., P_n have a port range
parameter value of one. Policy rule P_1 contains a set of address
tuples A0_1, A1_1, A2_1, and A3_1, that each contain the first port
number of the respective address tuples in P; policy rule P_2
contains a set of address tuples A0_2, A1_2, A2_2, and A3_2, that
each contain the second port number of the respective address tuples
in P; and so on.
2.3.7. Interface specific Policy Rules
Usually agents do request policy rules with the knowledge of A0 and
A3 only, i.e. the address tuples (see Section 2.3.5). But in very
special cases, agents may need to select the interfaces to which the
requested policy rule is bound. In the general case the middlebox
takes care about choosing the right interfaces when reserving or
enabling a policy rule, since it has the overall knowledge about its
configuration. For agents that want to select the interfaces,
optional parameters are include in the Policy Reserve Rule (PRR) and
Policy Enable Rule (PER) transactions. These parameter are called
- inside interface - the selected interface at the inside of the
middlebox, i.e. in the private or protected address realm.
- outside interface - the selected interface at the outside of the
middlebox, i.e. in the public address realm.
Stiemerling, Quittek, Taylor [Page 24]
Internet-Draft MIDCOM Protocol Semantics January 2004
The Policy Rule Status (PRS) transactions include these optional
parameters in its replies when they are supported.
Agents can learn at session startup whether interface specific policy
rules are supported by the middlebox or not, by checking the
middlebox capabilities (see Section 2.1.6).
2.3.8. Policy Reserve Rule (PRR)
transaction-name: policy reserve rule
transaction-type: configuration
transaction-compliance: mandatory
request-parameters:
- request identifier: an agent unique identifier for matching
corresponding request and reply at the agent.
- group identifier: a reference to the group of which the policy
reserve rule should be a member. As indicated in Section 2.3.3.,
if this value is not supplied, the middlebox assigns a new group
for this policy reserve rule.
- service: the requested NAT service of the middlebox. Allowed
values are 'traditional' or 'twice'.
- internal IP version: requested IP version at the inside of the
middlebox, see Section 2.3.5.
- internal IP address: the IP address of the internal communication
endpoint (A0 in Fig. 3), see Section 2.3.5.
- internal port number: the port number of the internal
communication endpoint (A0 in Fig. 3), see Section 2.3.5.
- inside interface (optional): interface at the inside of the
middlebox, see Section 2.3.7.
- external IP version: requested IP version at the outside of the
middlebox, see Section 2.3.5.
- outside interface (optional): interface at the outside of the
middlebox, see Section 2.3.7.
- transport protocol: see section 2.3.5.
Stiemerling, Quittek, Taylor [Page 25]
Internet-Draft MIDCOM Protocol Semantics January 2004
- port range: the number of consecutive port numbers to be
reserved, see Section 2.3.5.
- port parity: the requested parity of the first (lowest) port
number to be reserved, Allowed values of this parameter are
'odd', 'even', and 'any'. See also Section 2.3.5.
- policy rule lifetime: a lifetime proposal to the middlebox for
the requested policy rule.
reply-parameters (success):
- request identifier: an identifier matching the identifier of the
request.
- policy rule identifier: a middlebox unique policy rule
identifier. It is assigned by the middlebox and used as policy
rule handle in further policy rule transactions, particularly to
refer to the policy reserve rule in a subsequent PER transaction.
- group identifier: a reference to the group of which the policy
reserve rule is a member.
- reserved inside IP address: The reserved IPv4 or IPv6 address on
the internal side of the middlebox. For an outbound flow, this
will be the destination to which the internal endpoint sends its
packets (A1 in Figure 3). For an inbound flow, this will be the
apparent source address of the packets as forwarded to the
internal endpoint (A0 in Figure 3). The middlebox reserves and
reports an internal address only in the case where twice-NAT is
in effect. Otherwise, an empty value for the addresses indicates
that no internal reservation was made. See also Section 2.3.5.
- reserved inside port number: see section 2.3.5.
- reserved outside IP address: The reserved IPv4 or IPv6 address on
the external side of the middlebox. For an inbound flow, this
will be the destination to which the external endpoint sends its
packets (A2 in Figure 4). For an outbound flow, this will be the
apparent source address of the packets as forwarded to the
external endpoint (A3 in Figure 3). If the middlebox is
configured as a pure firewall, an empty value for the addresses
indicates that no external reservation was made. See also
Section 2.3.5.
- reserved outside port number: see section 2.3.5.
- policy rule lifetime: the policy rule lifetime granted by the
middlebox, after which the reservation will be revoked if it has
not been replaced already by a policy enable rule in a PER
Stiemerling, Quittek, Taylor [Page 26]
Internet-Draft MIDCOM Protocol Semantics January 2004
transaction.
failure reason:
- agent not authorized for this transaction
- agent not authorized for adding members to this group
- lack of IP addresses
- lack of port numbers
- lack of resources
- specified inside/outside interface does not exist
- specified inside/outside interface not available for specified
service
notification message type: Policy Rule Event Notification (REN)
semantics:
The agent can use this transaction type to reserve an IP address
or a combination of IP address, transport type, port number and
port range at neither, one, or both sides of the middlebox as
required to support the enabling of a flow. Typically the PRR
will be used in scenarios where it is required to perform such a
reservation before sufficient parameters for a complete policy
enable rule transaction are available. See section 4.2 for an
example.
When receiving the request, the middlebox determines how many
address (and port) reservations are required based on its
configuration. If it provides only packet filter services, it
does not perform any reservation and just returns empty values for
the reserved inside and outside IP addresses and port numbers. If
it is configured for twice-NAT, it reserves both inside and
outside IP addresses (and an optional range of port numbers) and
returns them. Otherwise, it reserves and returns an outside IP
address (and an optional range of port numbers) and returns empty
values for the reserved inside address and port range. The A0
parameter (inside IP address version, inside IP address, and
inside port number) can be used by the middlebox to determine the
correct NAT mapping and thus A2 if necessary.
Once a PRR transaction has reserved an outside address (A2) for an
internal end point (A0) at the middlebox, the middlebox must
ensure that this reserved A2 is available in any subsequent PER
and PRR transaction.
For middleboxes supporting interface specific policy rules, as
defined in Section 2.3.7., the optional inside and outside
interface parameters must be included both in the request or none
of them. In the presence of these parameters the middlebox uses
the outside interface parameter to select the interface at which
the outside address tuple (outside IP address and port number) is
Stiemerling, Quittek, Taylor [Page 27]
Internet-Draft MIDCOM Protocol Semantics January 2004
reserved, and the inside interface parameter to select the
interface at which the inside address tuple (inside IP address and
port number) is reserved. Without the presence of these
parameters, the middlebox selects the particular interfaces based
on its internal configuration.
If there is a lack of resources, such as available IP addresses,
port numbers, or storage for further policy rules, then the
reservation fails and an appropriate failure reply is generated.
If a non-existing policy rule group was specified, or if an
existing policy rule group was specified that is not owned by the
requesting agent, then no new policy rule is established and an
appropriate failure reply is generated.
In case of success, this transaction creates a new policy reserve
rule. If an already existing policy rule group is specified, then
the new policy rule becomes a member of it. If no policy group is
specified a new group is created with the new policy rule as its
only member. The middlebox generates a middlebox unique
identifier for the new policy rule. The owner of the new policy
rule is the authenticated agent that sent the request. The
middlebox chooses a lifetime value that is greater than zero and
less than or equal to the minimum of the requested value and the
maximum lifetime specified by the middlebox at session startup,
i.e.:
0 <= lt_granted <= MINIMUM(lt_requested, lt_maximum)
whereas:
- lt_granted is the actually granted lifetime by the middlebox
- lt_requested is the requested lifetime of the agent
- lt_maximum is the maximum lifetime specified at session
setup
The middlebox always reserves a middlebox external address tuple
(A2) due to a PRR request. In a special case of a combined twice-
NAT/NAT middlebox the agent can request only NAT service or twice-
NAT service by choosing the service parameter 'traditional' or
'twice' respectively. An agent that does not have any preference
chooses 'twice'. The 'traditional' value should only be used in
order to select traditional NAT service at middleboxes offering
both traditional NAT and twice NAT. In the 'twice' case the
combined twice-NAT/NAT middlebox reserves A2 and A1, the
'traditional' case results in a reservation of A2 only. An agent
must always use the PRR transaction for choosing NAT only or
twice-NAT service in the special case of a combined twice-NAT/NAT
middlebox. A firewall middlebox ignores this parameter.
If the protocol identifier is 'ANY', then the middlebox reserves
Stiemerling, Quittek, Taylor [Page 28]
Internet-Draft MIDCOM Protocol Semantics January 2004
available inside and/or outside IP address(es) only. The reserved
address(es) are returned to the agent. In this case the request-
parameters port range and port parity as well as reply-parameters
inside port number and outside port number are irrelevant.
If the protocol identifier is 'UDP' or 'TCP', then a combination
of an IP address and a consecutive sequence of port numbers,
starting with the specified parity, is reserved, on neither, one,
or both sides of the middlebox as appropriate. The IP address(es)
and the first (lowest) reserved port number(s) of the consecutive
sequence are returned to the agent. (This also applies to other
protocols supporting ports or the equivalent.)
After a new policy reserve rule was successfully established and
the reply message has been sent to the requesting agent, the
middlebox checks if there are other authenticated agents
participating in open sessions, which can access the new policy
rule. If the middlebox finds one or more of these agents, then it
sends a REN message reporting the new policy rule to each of them.
MIDCOM agents use the policy enable rule (PER) transaction to enable
policy reserve rules that have been established beforehand by a
policy reserve rule (PRR) transaction. See also Section 2.3.2.
2.3.9. Policy Enable Rule (PER)
transaction-name: policy enable rule
transaction-type: configuration
transaction-compliance: mandatory
request-parameters:
- request identifier: an agent unique identifier for matching
corresponding request and reply at the agent.
- policy reserve rule identifier: a reference to an already
existing policy reserve rule created by a PRR transaction. The
reference may be empty, in which case the middlebox must assign
any necessary addresses and port numbers within this PER
transaction. If it is not empty, then the following request
parameters are irrelevant: group identifier, transport protocol,
port range, port parity, internal IP version, external IP
version.
- group identifier: a reference to the group of which the policy
enable rule should be a member. As indicated in Section 2.3.3.,
if this value is not supplied, the middlebox assigns a new group
Stiemerling, Quittek, Taylor [Page 29]
Internet-Draft MIDCOM Protocol Semantics January 2004
for this policy reserve rule.
- transport protocol: see section 2.3.5.
- port range: the number of consecutive port numbers to be
reserved, see Section 2.3.5.
- port parity: the requested parity of the port number(s) to be
mapped. Allowed values of this parameter are 'same' and 'any'.
See also Section 2.3.5.
- direction of flow: this parameter specifies the direction of
enabled communication, either 'inbound', 'outbound', or 'bi-
directional'.
- internal IP version: requested IP version at the inside of the
middlebox, see Section 2.3.5.
- internal IP address: the IP address of the internal communication
endpoint (A0 in Fig. 3), see Section 2.3.5.
- internal port number: the port number of the internal
communication endpoint (A0 in Fig. 3), see Section 2.3.5.
- inside interface (optional): interface at the inside of the
middlebox, see Section 2.3.7.
- external IP version: requested IP version at the outside of the
middlebox, see Section 2.3.5.
- external IP address: the IP address of the external communication
endpoint (A3 in Fig. 3), see Section 2.3.5.
- external port number: the port number of the external
communication endpoint (A3 in Fig. 4), see Section 2.3.5.
- outside interface (optional): interface at the outside of the
middlebox, see Section 2.3.7.
- policy rule lifetime: a lifetime proposal to the middlebox for
the requested policy rule.
reply-parameters (success):
- request identifier: an identifier matching the identifier of the
request.
- policy rule identifier: a middlebox unique policy rule
identifier. It is assigned by the middlebox and used as policy
rule handle in further policy rule transactions. If a policy
Stiemerling, Quittek, Taylor [Page 30]
Internet-Draft MIDCOM Protocol Semantics January 2004
reserve rule identifier was provided in the request, then the
returned policy rule identifier has the same value.
- group identifier: a reference to the group of which the policy
enable rule is a member. If a policy reserve rule identifier was
provided in the request, then this parameter identifies the
group, of which the policy reserve rule was a member.
- inside IP address: the IP address provided at the inside of the
middlebox (A1 in Fig. 3). In case of a twice-NAT, this parameter
will be an internal IP address reserved at the inside of the
middlebox. In all other cases, this reply-parameter will be
identical with the external IP address passed with the request.
If the policy reserve rule identifier parameter was supplied in
the request and if the respective PRR transaction reserved an
inside IP address, then the inside IP address provided in the PER
response will be the identical value to that returned by the
response to the PRR request. See also Section 2.3.5.
- inside port number: the internal port number provided at the
inside of the middlebox (A1 in Fig. 3), see also Section 2.3.5.
- outside IP address: the external IP address provided at the
outside of the middlebox (A2 in Fig. 4). In case of a pure
firewall, this parameter will be identical with the internal IP
address passed with the request. In all other cases, this reply-
parameter will be an external IP address reserved at the outside
of the middlebox. See also Section 2.3.5.
- outside port number: the external port number provided at the
outside of the NAT (A2 in Fig. 3), see Section 2.3.5..
- policy rule lifetime: the policy rule lifetime granted by the
middlebox.
failure reason:
- agent not authorized for this transaction
- agent not authorized for adding members to this group
- no such policy reserve rule
- agent not authorized for replacing this policy reserve rule
- conflict with already existing policy rule (e.g. the same
internal address-port is being mapped to different outside
address-port pairs)
- lack of IP addresses
- lack of port numbers
- lack of resources
- no internal IP wildcarding allowed
- no external IP wildcarding allowed
- specified inside/outside interface does not exist
- specified inside/outside interface not available for specified
Stiemerling, Quittek, Taylor [Page 31]
Internet-Draft MIDCOM Protocol Semantics January 2004
service
- reserved A0 to requested A0 mismatch
notification message type: Policy Rule Event Notification (REN)
semantics:
This transaction can be used by an agent for enabling
communication between an internal endpoint and an external
endpoint independently of the type of middlebox (NAT, NAPT,
firewall, NAT-PT, combined devices, ... ), for unidirectional or
bi-directional traffic.
The agent sends an enable request specifying the endpoints
(optionally including wildcards) and the direction of
communication (inbound, outbound, bi-directional). The
communication endpoints are displayed in Figure 3. The basic
operation of the PER transaction can be described by
1. the agent sending A0 and A3 to the middlebox,
2. the middlebox reserving A1 and A2 or using A1 and A2 from a
previous PRR transaction
3. the middlebox enabling packet transfer between A0 and A3 by
binding A0-A2 and A1-A3 and/or by opening the corresponding
pinholes, both according to the specified direction,
4. the middlebox returning A1 and A2 to the agent.
In case of a pure packet filtering firewall, the returned address
tuples are the same as the ones in the request: A2=A0 and A1=A3.
Each partner uses the other one's real address. In case of a
traditional NAT the internal endpoint may use the real address of
the external endpoint (A1=A3), but the external endpoint uses an
address tuple provided by the NAT (A2!=A0). In case of a twice-
NAT device, both endpoints use address tuples provided by the NAT
for addressing their communication partner (A3!=A1 and A2!=A0).
If a firewall is combined with a NAT or a twice-NAT, the replied
address tuples will be the same as for pure traditional NAT or
twice-NAT, respectively, but the middlebox will configure its
packet filter in addition to the performed NAT bindings. In case
of a firewall combined with a traditional NAT, the policy rule may
imply more than one enable action for the firewall configuration,
because incoming and outgoing packets may use different source-
destination pairs.
For middleboxes supporting interface specific policy rules, as
defined in Section 2.3.7., the optional inside and outside
Stiemerling, Quittek, Taylor [Page 32]
Internet-Draft MIDCOM Protocol Semantics January 2004
interface parameters must be included both in the request or none
of them. In the presence of these parameters the middlebox uses
the outside interface parameter to select the interface at which
the outside address tuple (outside IP address and port number) is
bound, and the inside interface parameter to select the interface
at which the inside address tuple (inside IP address and port
number) is bound. Without the presence of these parameters, the
middlebox selects the particular interfaces based on its internal
configuration.
Checking the policy reservation rule identifier
If the parameter specifying the policy reservation rule
identifier is not empty, then the middlebox checks whether or
not the referenced policy rule exists, whether or not the agent
is authorized to replace this policy rule, and whether or not
this policy rule is a policy reserve rule.
In case of success, this transaction creates a new policy
enable rule. If a policy reserve rule was referenced, then the
policy reserve rule is terminated without an explicit
notification sent to the agent (besides the successful PER
reply).
The PRR transaction sets the internal endpoint A0 during the
reservation process. In the process of creating a new policy
enable rule, the middlebox may check whether the requested A0
is equal to the reserved A0. The middlebox may reject a PER
request with a requested A0 not equal to the reserved A0 and
must sent an appropriate failure message. The middlebox may
change A0 due to the PER request.
The middlebox generates a middlebox unique identifier for the
new policy rule. If a policy reserve rule was referenced, then
the identifier of the policy reserve rule is re-used.
The owner of the new policy rule is the authenticated agent
that sent the request.
Checking the policy rule group identifier
If no policy reserve rule was specified, then the policy rule
group parameter is checked. If a non-existing policy rule group
is specified, or if an existing policy rule group is specified
that is not owned by the requesting agent, then no new policy
rule is established and an appropriate failure reply is
generated.
If an already existing policy rule group is specified, then the
new policy rule becomes a member of it. If no policy group is
Stiemerling, Quittek, Taylor [Page 33]
Internet-Draft MIDCOM Protocol Semantics January 2004
specified, then a new group is created with the new policy rule
as its only member.
If the transport protocol parameter value is 'any', then the
middlebox enables communication between the specified external IP
address and the specified internal IP address. The addresses to
be used by the communication partners in order to address each
other are returned to the agent as inside IP address and outside
IP address. If the reservation identifier is not empty and if the
reservation used the same transport protocol type, then the
reserved IP addresses are used.
For the transport protocol parameter values 'UDP' and 'TCP' the
middlebox acts analogously to 'ANY' but additionally maps ranges
of port numbers, keeping the port parity if requested.
The configuration of the middlebox may fail because of lack of
resources, such as available IP addresses, port numbers, or
storage for further policy rules. Also it may fail because of a
conflict with an already established policy rule. In case of a
conflict, the first come first serve mechanism is applied.
Already existing policy rules remain unchanged and arriving new
ones are rejected. However, in case of a non-conflicting overlap
of policy rules (including identical policy rules), all policy
rules are accepted.
The middlebox chooses a lifetime value that is greater than zero
and less than or equal to the minimum of the requested value and
the maximum lifetime specified by the middlebox at session
startup, i.e.:
0 <= lt_granted <= MINIMUM(lt_requested, lt_maximum)
whereas:
- lt_granted is the actually granted lifetime by the middlebox
- lt_requested is the requested lifetime of the agent
- lt_maximum is the maximum lifetime specified at session
setup
In each case of failure, an appropriate failure reply is
generated. The policy reserve rule that is referenced in the PER
transaction is not affected in case of a failure within the PER
transaction, i.e. the policy reserve rule remains.
After a new policy enable rule was successfully established and
the reply message has been sent to the requesting agent, the
middlebox checks if there are other authenticated agents
participating in open sessions, which can access the new policy
rule. If the middlebox finds one or more of these agents, then it
sends a REN message reporting the new policy rule to each of them.
Stiemerling, Quittek, Taylor [Page 34]
Internet-Draft MIDCOM Protocol Semantics January 2004
2.3.10. Policy Rule Lifetime Change (RLC)
transaction-name: policy rule lifetime change
transaction-type: configuration
transaction-compliance: mandatory
request-parameters:
- request identifier: an agent unique identifier for matching
corresponding request and reply at the agent.
- policy rule identifier: identifying the policy rule for which the
lifetime is requested to be changed. This may identify either a
policy reserve rule or a policy enable rule.
- policy rule lifetime: the new lifetime proposal for the policy
rule.
reply-parameters (success):
- request identifier: an identifier matching the identifier of the
request.
- policy rule lifetime: The remaining policy rule lifetime granted
by the middlebox.
failure reason:
- agent not authorized for this transaction
- agent not authorized for changing lifetime of this policy
rule
- no such policy rule
- lifetime cannot be extended
notification message type: Policy Rule Event Notification (REN)
semantics:
The agent can use this transaction type to request the extension
of an already established policy rule's lifetime, to request
shortening of the life time, or to request policy rule
termination. Policy rule termination is requested by suggesting a
new policy rule lifetime of zero.
The middlebox first checks whether or not the specified policy
rule exists and whether or not the agent is authorized to access
this policy rule. If one of the checks fails, an appropriate
failure reply is generated. If the requested lifetime is longer
than the current one, the middlebox also checks, whether or not
Stiemerling, Quittek, Taylor [Page 35]
Internet-Draft MIDCOM Protocol Semantics January 2004
the lifetime of the policy rule may be extended and generates an
appropriate failure message if not.
A failure reply implies that the new lifetime was not accepted,
and the policy rule remains unchanged. A success reply is
generated by the middlebox, if the lifetime of the policy rule was
changed in any way.
The success reply contains the new lifetime of the policy rule.
The middlebox chooses a lifetime value that is greater than zero
and less than or equal to the minimum of the requested value and
the maximum lifetime specified by the middlebox at session
startup, i.e.:
0 <= lt_granted <= MINIMUM(lt_requested, lt_maximum)
whereas:
- lt_granted is the actually granted lifetime by the middlebox
- lt_requested is the requested lifetime of the agent
- lt_maximum is the maximum lifetime specified at session
setup
After sending a success reply with a lifetime of zero, the
middlebox will consider the policy rule to be non-existent. Any
further transaction on this policy rule results in a negative
reply, indicating that this policy rule does not exist anymore.
Please note, that policy rule lifetime may also be changed by the
Group Lifetime Change (GLC) transaction if applied to the group of
which the policy rule is a member.
After the remaining policy rule lifetime was successfully changed
and the reply message has been sent to the requesting agent, the
middlebox checks if there are other authenticated agents
participating in open sessions, which can access the policy rule.
If the middlebox finds one or more of these agents, then it sends
a REN message reporting the new remaining policy rule lifetime to
each of them.
2.3.11. Policy Rule List (PRL)
transaction-name: policy rule list
transaction-type: monitoring
transaction-compliance: mandatory
request-parameters:
Stiemerling, Quittek, Taylor [Page 36]
Internet-Draft MIDCOM Protocol Semantics January 2004
- request identifier: an agent unique identifier for matching
corresponding request and reply at the agent.
reply-parameters (success):
- request identifier: an identifier matching the identifier of the
request.
- policy list: list of policy rule identifiers of all policy rules
that the agent can access.
failure reason:
- transaction not supported
- agent not authorized for this transaction
semantics:
The agent can use this transaction type to list all policies which
it can access. Usually, the agent has this information already,
but in special cases (for example after an agent fail-over) or for
special agents (for example an administrating agent that can
access all policies) this transaction can be helpful.
The middlebox first checks whether or not the agent is authorized
to request this transaction. If the check fails, an appropriate
failure reply is generated. Otherwise a list of all policies the
agent can access is returned indicating the identifier and the
owner of each policy.
This transaction does not have any effect on the policy rule
state.
2.3.12. Policy Rule Status (PRS)
transaction-name: policy rule status
transaction-type: monitoring
transaction-compliance: mandatory
request-parameters:
- request identifier: an agent unique identifier for matching
corresponding request and reply at the agent.
- policy rule identifier: the middlebox unique policy rule
identifier.
reply-parameters (success):
Stiemerling, Quittek, Taylor [Page 37]
Internet-Draft MIDCOM Protocol Semantics January 2004
- request identifier: an identifier matching the identifier of the
request.
- policy rule owner: an identifier of the agent owning this policy
rule.
- group identifier: a reference to the group of which the policy
rule is a member.
- policy rule action: this parameter has either the value 'reserve'
or the value 'enable'.
- transport protocol: identifies the protocol for which a
reservation is requested, see Section 2.3.5.
- port range: the number of consecutive port numbers, see Section
2.3.5.
- direction: the direction of the communication enabled by the
middlebox. Applicable only to policy enable rules.
- internal IP address version: the version of the internal IP
address (IP version of A0 in Fig. 3)
- external IP address version: the version of the external IP
address (IP version of A3 in Fig. 3)
- internal IP address: the IP address of the internal communication
endpoint (A0 in Fig. 3), see Section 2.3.5.
- internal port number: the port number of the internal
communication endpoint (A0 in Fig. 3), see Section 2.3.5.
- external IP address: the IP address of the external communication
endpoint (A3 in Fig. 3), see Section 2.3.5.
- external port number: the port number of the external
communication endpoint (A3 in Fig. 3), see Section 2.3.5.
- inside interface (optional): the inside interface at the
middlebox, see Section 2.3.7.
- inside IP address: the internal IP address provided at the inside
of the NAT (A1 in Fig. 3), see Section 2.3.5.
- inside port number: the internal port number provided at the
inside of the NAT (A1 in Fig. 3), see Section 2.3.5.
- outside interface (optional): the outside interface at the
middlebox, see Section 2.3.7.
Stiemerling, Quittek, Taylor [Page 38]
Internet-Draft MIDCOM Protocol Semantics January 2004
- outside IP address: the external IP address provided at the
outside of the NAT (A2 in Fig. 3), see Section 2.3.5.
- outside port number: the external port number provided at the
outside of the NAT (A2 in Fig. 3), see Section 2.3.5.
- port parity: The parity of the allocated ports.
- service: The selected service in the case of mixed traditional
and twice-NAT middlebox(see section 2.3.8.)
- policy rule lifetime: the remaining lifetime of the policy rule.
failure reason:
- transaction not supported
- agent not authorized for this transaction
- no such policy rule
- agent not authorized for accessing this policy rule
semantics:
The agent can use this transaction type to list all properties of
a policy rule. Usually, the agent has this information already,
but in special cases (for example after an agent fail-over) or for
special agents (for example an administrating agent that can
access all policy rules) this transaction can be helpful.
The middlebox first checks whether or not the specified policy
rule exists and whether or not the agent is authorized to access
this group. If one of the checks fails, an appropriate failure
reply is generated. Otherwise all properties of the policy rule
are returned to the agent. Some of the returned parameters may be
irrelevant, depending on the policy rule action ('reserve' or
'enable') and depending on other parameters, for example the
protocol identifier.
This transaction does not have any effect on the policy rule
state.
2.3.13. Asynchronous Policy Rule Event (ARE)
transaction-name: asynchronous policy rule event
transaction-type: notification
transaction-compliance: mandatory
notification message type: Policy Rule Event Notification (REN)
Stiemerling, Quittek, Taylor [Page 39]
Internet-Draft MIDCOM Protocol Semantics January 2004
semantics:
The middlebox may decide at any point in time to terminate a
policy rule. Particularly, this transaction is triggered by
lifetime expiration of the policy rule. Among other events that
may cause this transaction are changes in the policy rule decision
point.
The middlebox sends a REN message to all agents that participate
in an open session with the middlebox and that are authorized to
access the policy rule. The notification is sent to the agents
before the middlebox changes the policy rule's lifetime. The
change of lifetime may be triggered by any other authorized agent
and results in shortening (lt_new < lt_exisiting), extending
(lt_new > lt_existing), or in terminating the policy rule (lt_new
= 0).
The ARE transaction corresponds to the REN message handling described
in Section 2.3.4. for multiple agents.
2.3.14. Policy Rule State Machine
The state machine for the policy rule transactions is shown in Figure
4 with all possible state transitions. You'll find the used
transaction abbreviations in the headings of the particular
transaction section.
PRR/success +---------------+
+-----------------+ PRID UNUSED |<-+
+----+ | +---------------+ |
| | | ^ | |
| v v | | |
| +-------------+ ARE | | PER/ | ARE
| | RESERVED +------------+ | success | RLC(lt=0)/
| +-+----+------+ RLC(lt=0)/ | | success
| | | success | |
+----+ | v |
RLC(lt>0)/ | PER/success +---------------+ |
success +---------------->| ENABLED +--+
+-+-------------+
| ^
lt = lifetime +-----------+
RLC(lt>0)/success
Figure 4: Policy Rule State Machine
This state machine exists per policy rule identifier (PRID).
Initially, all policy rules are in state PRID UNUSED, which means
Stiemerling, Quittek, Taylor [Page 40]
Internet-Draft MIDCOM Protocol Semantics January 2004
that the policy rule does not exist or is not active. After
returning to state PRID UNUSED, the policy rule identifier is no
longer bound to an existing policy rule and may be re-used by the
middlebox.
A successful PRR transaction causes a transition from the initial
state PRID UNUSED to state RESERVED, where an address reservation is
established. From there, state ENABLED can be entered by a PER
transaction. This transaction can also be used for entering state
ENABLED directly from state PRID UNUSED without a reservation. In
state ENABLED the requested communication between the internal and
the external endpoint is enabled.
The states RESERVED and ENABLED can be maintained by a successful RLC
transactions with a requested lifetime greater than 0. Transitions
from both of these states back to state PRID UNUSED can be caused by
an ARE transaction or by a successful RLC transaction with a lifetime
parameter of 0.
A failed request transactions does not change state at the middlebox.
Please note, transitions initiated by RLC transactions may also be
initiated by GLC transactions.
2.4. Policy Rule Group Transactions
This section describes the semantics for transactions on groups of
policy rules. These transactions are specified:
- Group Lifetime Change (GLC)
- Group List (GL)
- Group Status (GS)
All are request transactions initiated by the agent. GLC is a
convenience transaction. GL and GS are monitoring transactions that
do not have any effect on the group state machine.
2.4.1. Overview
A policy rule group has only one attribute: the list of its members.
All member policies of a single group must be owned by the same
authenticated agent. Therefore, an implicit property of a group is
its owner, which is the owner of the member policy rules.
A group is created implicitly, when its first member policy rule is
established. A group is terminated implicitly, when the last
remaining member policy rule is terminated. Consequently, the
lifetime of a group is the maximum of the lifetimes of all member
Stiemerling, Quittek, Taylor [Page 41]
Internet-Draft MIDCOM Protocol Semantics January 2004
policy rules.
A group has a middlebox unique identifier.
Group transactions are declared as 'optional' by their respective
compliance entry in Section 3. However, they provide some
functionality, like convenience for the agent in sending only one
request instead of several, that is not available if only mandatory
transactions are available.
The Group Lifetime Change (GLC) transaction is equivalent to
simultaneously performed Policy Rule Lifetime Change (RLC)
transactions on all members of the group. The result of a successful
GLC transaction is that all member policy rules have the same
lifetime. Analogously to the RLC transaction, the GLC transaction
can be use for deleting all member policy rules by requesting a
lifetime of zero.
The monitoring transactions Group List (GL) and Group Status (GS) can
be used by the agent for exploring the state of the middlebox and for
exploring its access rights. The GL transaction lists all groups
that the agent may access, including groups owned by other agents.
The GS transaction reports the status on an individual group and it
lists all policy rules of this group by their policy rule
identifiers. The agent can explore the state of the individual
policy rules by using the policy rule identifiers in a policy rule
status (PRS) transaction (see Section 2.3.12).
The GL and GS transactions are particularly helpful in case of an
agent fail-over. The agent taking over the role of a failed one can
use these transactions for retrieving which policies has been
established by the failed agent.
Notifications on group events are generated analogously to policy
rule events. For notifying agents about group events, the Policy
Rule Group Event Notification (GEN) message type is used. GEN
messages contain a agent unique notification identifier, the policy
rule group identifier and the remaining lifetime of the group.
2.4.2. Group Lifetime Change (GLC)
transaction-name: group lifetime change
transaction-type: convenience
transaction-compliance: optional
request-parameters:
Stiemerling, Quittek, Taylor [Page 42]
Internet-Draft MIDCOM Protocol Semantics January 2004
- request identifier: an agent unique identifier for matching
corresponding request and reply at the agent.
- group identifier: a reference to the group for which the lifetime
is requested to be changed.
- group lifetime: the new lifetime proposal for the group.
reply-parameters (success):
- request identifier: an identifier matching the identifier of the
request.
- group lifetime: The group lifetime granted by the middlebox.
failure reason:
- transaction not supported
- agent not authorized for this transaction
- agent not authorized for changing lifetime of this group
- no such group
- lifetime cannot be extended
notification message type: Policy Rule Group Event Notification (GEN)
semantics:
The agent can use this transaction type to request an extension of
the lifetime of all members of a policy rule group, to request
shortening the lifetime of all members, or to request termination
of all member policies (which implies termination of the group).
Termination is requested by suggesting a new group lifetime of
zero.
The middlebox first checks whether or not the specified group
exists and whether or not the agent is authorized to access this
group. If one of the checks fails, an appropriate failure reply
is generated. If the requested lifetime is longer than the
current one, the middlebox also checks whether or not the lifetime
of the group may be extended and generates an appropriate failure
message if not.
A failure reply implies that the lifetime of the group remains
unchanged. A success reply is generated by the middlebox if the
lifetime of the group was changed in any way.
The success reply contains the new common lifetime of all member
policy rules of the group. The middlebox chooses the new lifetime
less than or equal to the minimum of the requested lifetime and
the maximum lifetime that the middlebox specified at session setup
together with its other capabilities, i.e.:
Stiemerling, Quittek, Taylor [Page 43]
Internet-Draft MIDCOM Protocol Semantics January 2004
0 <= lt_granted <= MINIMUM(lt_requested, lt_maximum)
whereas:
- lt_granted is the actually granted lifetime by the middlebox
- lt_requested is the requested lifetime of the agent
- lt_maximum is the maximum lifetime specified at session
setup
After sending a success reply with a lifetime of zero, the member
policy rules will be terminated without any further notification
to the agent, and the middlebox will consider the group and all of
its members to be non-existent. Any further transaction on this
policy rule group or on any of its members results in a negative
reply, indicating that this group or policy rule, respectively,
does not exist anymore.
After the remaining policy rule group lifetime was successfully
changed and the reply message has been sent to the requesting
agent, the middlebox checks if there are other authenticated
agents participating in open sessions, which can access the policy
rule group. If the middlebox finds one or more of these agents,
then it sends a GEN message reporting the new remaining policy
rule group lifetime to each of them.
2.4.3. Group List (GL)
transaction-name: group list
transaction-type: monitoring
transaction-compliance: optional
request-parameters:
- request identifier: an agent unique identifier for matching
corresponding request and reply at the agent.
reply-parameters (success):
- request identifier: an identifier matching the identifier of the
request.
- group list: list of all groups that the agent can access. For
each listed group the identifier and the owner are indicated.
failure reason:
- transaction not supported
- agent not authorized for this transaction
Stiemerling, Quittek, Taylor [Page 44]
Internet-Draft MIDCOM Protocol Semantics January 2004
semantics:
The agent can use this transaction type to list all groups which
it can access. Usually, the agent has this information already,
but in special cases (for example after an agent fail-over) or for
special agents (for example an administrating agent that can
access all groups) this transaction can be helpful.
The middlebox first checks whether or not the agent is authorized
to request this transaction. If the check fails, an appropriate
failure reply is generated. Otherwise a list of all groups the
agent can access is returned indicating the identifier and the
owner of each group.
This transaction does not have any effect on the group state.
2.4.4. Group Status (GS)
transaction-name: group status
transaction-type: monitoring
transaction-compliance: optional
request-parameters:
- request identifier: an agent unique identifier for matching
corresponding request and reply at the agent.
- group identifier: a reference to the group for which status
information is requested.
reply-parameters (success):
- request identifier: an identifier matching the identifier of the
request.
- group owner: an identifier of the agent owning this policy rule
group.
- group lifetime: the remaining lifetime of the group. This is the
maximum of the remaining lifetime of all members policy rules.
- member list: list of all policy rules that are members of the
group. The policy rules are specified by their middlebox unique
policy rule identifier.
failure reason:
- transaction not supported
Stiemerling, Quittek, Taylor [Page 45]
Internet-Draft MIDCOM Protocol Semantics January 2004
- agent not authorized for this transaction
- no such group
- agent not authorized for listing members of this group
semantics:
The agent can use this transaction type to list all member policy
rules of a group. Usually, the agent has this information
already, but in special cases (for example after an agent fail-
over) or for special agents (for example an administrating agent
that can access all groups) this transaction can be helpful.
The middlebox first checks whether or not the specified group
exists and whether or not the agent is authorized to access this
group. If one of the checks fails, an appropriate failure reply
is generated. Otherwise a list of all group members is returned
indicating the identifier of each group.
This transaction does not have any effect on the group state.
3. Conformance Statements
A protocol definition complies with the semantics defined in Section
2 if the protocol specification includes all specified transactions
with all their mandatory parameters. However, concrete
implementations of the protocol may support only some of the optional
transactions, but not all of them. Which transactions are required
for compliancy is different for agent and middlebox.
This section contains conformance statements for MIDCOM protocol
implementations related to the semantics. Conformance is specified
differently for agents and middleboxes. Most probably these
conformance statements will be extended by a concrete protocol
specification. However, such an extension is expected to extend the
statements below in a way that all of them still hold.
The following list shows the transaction-compliance property of all
transactions as specified in the previous section:
- Session Control Transactions
- Session Establishment (SE) mandatory
- Session Termination (ST) mandatory
- Asynchronous Session Termination (AST) mandatory
- Policy Rule Transactions
- Policy Reserve Rule (PRR) mandatory
- Policy Enable Rule (PER) mandatory
- Policy Rule Lifetime Change (RLC) mandatory
- Policy Rule List (PRL) mandatory
Stiemerling, Quittek, Taylor [Page 46]
Internet-Draft MIDCOM Protocol Semantics January 2004
- Policy Rule Status (PRS) mandatory
- Asynchronous Policy Rule Event (ARE) mandatory
- Policy Rule Group Transactions
- Group Lifetime Change (GLC) optional
- Group List (GL) optional
- Group Status (GS) optional
3.1. General Implementation Conformance
A compliant implementation of a MIDCOM protocol must support all
mandatory transactions.
A compliant implementation of a MIDCOM protocol may support none,
one, or more of the following transactions: GLC, GL, GS.
A compliant implementation may extend the protocol semantics by
further transactions.
A compliant implementation of a MIDCOM protocol must support all
mandatory parameters of each transaction concerning the information
contained. The set of parameters can be redefined per transaction as
long as the contained information is maintained.
A compliant implementation of a MIDCOM protocol may support the use
of interface specific policy rules. The optional inside and outside
interface parameters in PRR, PER, and PRS must be included both or
none of them when interface specific policy rules are supported.
A compliant implementation may extend the list of parameters of
transactions.
A compliant implementation may replace a single transaction by a set
of more fine-grained transactions. In such a case, it must be
ensured, that requirement 2.1.4 (deterministic behavior) and
requirement 2.1.5 (known and stable state) of [MDC-REQ] are still
met. When a single transaction is replaced by a set of multiple
fine-grained transactions, this set must be equivalent to a single
transaction. This multiple fine-grained transactions must further
meet the atomicity requirement stated in section 2.1.3.
3.2. Middlebox Conformance
A middlebox implementation of a MIDCOM protocol supports a request
transaction if it is able to receive and process all possible correct
message instances of the particular request transaction and if it
generates a correct reply for any correct request it receives.
Stiemerling, Quittek, Taylor [Page 47]
Internet-Draft MIDCOM Protocol Semantics January 2004
A middlebox implementation of a MIDCOM protocol supports a
asynchronous transaction if it is able to generate the corresponding
notification message properly.
A compliant middlebox implementation of a MIDCOM protocol must inform
the agent about the list of supported transactions within the SE
transaction.
3.3. Agent Conformance
An agent implementation of a MIDCOM protocol supports a request
transaction if it is able to generate the corresponding request
message properly and if it is able to receive and process all
possible correct replies to the particular request.
An agent implementation of a MIDCOM protocol supports a asynchronous
transaction if it is able to receive and process all possible correct
message instances of the particular transaction.
A compliant agent implementation of a MIDCOM protocol must not use
any optional transaction that is not supported by the middlebox. The
middlebox informs the agent about the list of supported transactions
within the SE transaction.
4. Transaction Usage Examples
This section gives two usage examples of the transactions specified
in Section 2. First it is shown, how an agent can explore all policy
rules and policy rule groups, which it may access at a middlebox.
Then the middlebox configuration for enabling a SIP-signaled call is
demonstrated.
4.1. Exploring Policy Rules and Policy Rule Groups
This example assumes an already established session. It shows how an
agent can find out
- which groups it may access and who owns these groups
- the status and member list of all accessible groups
- the status and properties of all accessible policy rules
If there is just a single session, there is no need for any of these
actions, because the middlebox informs the agent about each state
transition of any policy rule or policy rule group. However, after
the disruption of a session or after an intentional session
termination, the agent might want to re-establish the session and
explore, which of the groups and policy rules it established are
Stiemerling, Quittek, Taylor [Page 48]
Internet-Draft MIDCOM Protocol Semantics January 2004
still in place.
Also an agent system may fail and another one takes over. Then the
other one need to find out what has already been configured by the
failing system and what still needs to be done.
A third situation where exploring policy rules and groups is useful
is the case of an agent with 'administrator' authorization. This
agent may access any policy rule or group created by any other agent
and modify them.
All of them probably will start their exploration with the Group List
(GL) transaction, as shown in Figure 5. On this request, the
middlebox returns a list of pairs each containing an agent identifier
and a group identifier (GID). The agent gets informed which own
group and which of other agents' groups it may access.
agent middlebox
| GL |
|**********************************************>|
|<**********************************************|
| (agent1,GID1) (agent1,GID2) (agent2,GID3) |
| |
| GS GID2 |
|**********************************************>|
|<**********************************************|
| agent1 lifetime PID1 PID2 PID3 PID4 |
| |
Figure 5: Using the GL and the GS transaction
In Figure 5 three groups are accessible to the agent, and the agent
retrieves information about the second group by using the Group
Status (GS) transaction. It receives the owner of the group, the
remaining lifetime, and the list of member policy rules, in this case
containing four policy rule identifiers (PIDs).
In the following, the agent explores these four policy rules. The
example assumes the middlebox to be a traditional NAPT. Figure 6
shows the exploration of the first policy rule. As reply to a Policy
Rule Status (PRS) transaction, the middlebox always returns the
following list of parameters:
- policy rule owner
- group identifier
- policy rule action (reserve or enable)
- protocol type
- port range
- direction
- internal IP address
Stiemerling, Quittek, Taylor [Page 49]
Internet-Draft MIDCOM Protocol Semantics January 2004
- internal port number
- external address
- external port number
- middlebox inside IP address
- middlebox inside port number
- middlebox outside IP address
- middlebox outside port number
- IP address versions (not printed)
- middlebox service (not printed)
- inside and outside interface (not printed and optional)somit
agent middlebox
| PRS PID1 |
|**********************************************>|
|<**********************************************|
| agent1 GID2 RESERVE UDP 1 |
| ANY ANY ANY ANY |
| ANY ANY IPADR_OUT PORT_OUT1 |
| |
Figure 6: Status report for an outside reservation
The `ANY' parameter printed in Figure 6 is used as a placeholder in
policy rules status replies for policy reserve rules. The policy
rule with PID1 is a policy reserve rule for UDP traffic at the
outside of the middlebox. Since there is no internal or external
address involved yet, these four fields are wildcarded in the reply.
The same holds for the inside middlebox address and port number. The
only address information given by the reply is the reserved outside
IP address of the middlebox (IPADDR_OUT) and the corresponding port
number (PORT_OUT1). Note, that IPADR_OUT and PORT_OUT1 may not be
wildcarded, because the reserve action does not support this.
Applying PRS to PID2 (Figure 7) shows that the second policy rule is
an policy enable rule for inbound UDP packets. The internal
destination is fixed concerning IP address, protocol and port number,
but for the external source, the port number is wildcarded. The
outside IP address and port number of the middlebox are the ones the
external sender needs to use as destination in the original packet it
sends. At the middlebox, the destination address is replaced with
the internal address of the final receiver. During address
translation, the source IP address and the source port numbers of the
packets remain unchanged. This is indicated by the inside address
which is identical to the external address.
Stiemerling, Quittek, Taylor [Page 50]
Internet-Draft MIDCOM Protocol Semantics January 2004
agent middlebox
| PRS PID2 |
|**********************************************>|
|<**********************************************|
| agent1 GID2 ENABLE UDP 1 IN |
| IPADR_INT PORT_INT1 IPADR_EXT ANY |
| IPADR_EXT ANY IPADR_OUT PORT_OUT2 |
| |
Figure 7: Status report for enabled inbound packets
For traditional NATs the identity of the inside IP address and port
number with the external IP address and port number always holds
(A1=A3 in Figure 3). For a pure firewall, also the outside IP
address and port number are always identical with the internal IP
address and port number (A0=A2 in Figure 3).
agent middlebox
| PRS PID3 |
|**********************************************>|
|<**********************************************|
| agent1 GID2 ENABLE UDP 1 OUT |
| IPADR_INT PORT_INT2 IPADR_EXT PORT_EXT1 |
| IPADR_EXT PORT_EXT1 IPADR_OUT PORT_OUT3 |
| |
Figure 8: Status report for enabled outbound packets
Figure 8 shows enabled outbound UDP communication between the same
host. Here all port numbers are known. Since again A1=A3, the
internal sender uses the external IP address and port number as
destination in the original packets. At the firewall, the internal
source IP address and port number are replaced by the shown outside
IP address and port number of the middlebox.
agent middlebox
| PRS PID4 |
|**********************************************>|
|<**********************************************|
| agent1 GID2 ENABLE TCP 1 BI |
| IPADR_INT PORT_INT3 IPADR_EXT PORT_EXT2 |
| IPADR_EXT PORT_EXT2 IPADR_OUT PORT_OUT4 |
| |
Figure 9: Status report for bi-directional TCP traffic
Finally, Figure 9 shows the status report for enabled bi-directional
TCP traffic. Please note that still A1=A3: For outbound packets, only
Stiemerling, Quittek, Taylor [Page 51]
Internet-Draft MIDCOM Protocol Semantics January 2004
the source IP address and port number are replaced at the middlebox,
and for inbound packets, only the destination IP address and port
number are replaced.
4.2. Enabling a SIP-Signaled Call
This elaborated transaction usage example shows the interaction
between a SIP proxy and a middlebox. The middlebox itself is a
traditional Network Address and Port Translation (NAPT) and two SIP
user agents communicate with each other via the SIP proxy and NAPT as
shown in figure 10. The MIDCOM agent is co-located with the SIP
proxy and the MIDCOM server is at the middlebox. Thus the MIDCOM
protocol runs between the SIP proxy and middlebox
+----------+
|SIP Proxy |
|for domain++++
| mb.com | +
+----------+ +
Private ^ ^ + Public Network
Network | | +
+----------+ | | +---+-----+ +----------+
| SIP User |<-+ +->|Middlebox|<------->| SIP User |
| Agent A |<#######>| NAPT |<#######>| Agent B |
+----------+ +---------+ +----------+
<--> SIP Signaling
<##> RTP Traffic
++++ MIDCOM protocol
Figure 10: Example SIP Scenario
For the below sequence charts we make these assumptions:
- The NAPT is statically configured to forward SIP signaling from
the outside to the SIP proxy server, i.e. traffic to the NAPT's
external IP address and port 5060 is forwarded to the internal
SIP proxy.
- The SIP user agent A, located inside the private network, is
registered at the SIP proxy with its private IP address.
- User A knows the general SIP URL of user B. The URL is B@b.de.
However, the concrete URL of the SIP User Agent B, which user B
currently uses is not known.
Stiemerling, Quittek, Taylor [Page 52]
Internet-Draft MIDCOM Protocol Semantics January 2004
- Only the RTP paths are configured, but not the RTCP paths.
- The middlebox and the SIP server share an already established
MIDCOM session.
- Some parameters are omitted, like the request identifier (RID)
Furthermore these abbreviations are used:
- IP_AI: Internal IP address of user agent A
- P_AI: Internal port number of user agent A to receive RTP data
- P_AE: External mapped port number of user agent A
- IP_AE: External IP address of the middlebox
- IP_B: IP address of user agent B
- P_B: Port number of user agent B to receive RTP data
- GID: Group identifier
- PID: Policy rule identifier
The abbreviations of the MIDCOM transactions can be found in the
particular section headings.
In our example, user A tries to call user B. Therefore, the user
agent A sends an INVITE SIP message to the SIP proxy server (see
Figure 10). The SDP part of the particular SIP message that is
relevant for the middlebox configuration is shown in the sequence
chart as:
SDP: m=..P_AI..
c=IP_AI
where the m tag is the media tag which contains the receiving UDP
port number and the c tag contains the IP address of the terminal
receiving the media stream.
The INVITE message forwarded to user agent B must contain a public IP
address and a port number to which user agent B can send its RTP
media stream. The SIP proxy requests a policy enable rule at the
middlebox with a PER request with wildcarded IP address and port
number of user agent B. Since neither IP address nor port numbers of
user agent B are known at this point of time, the address of user
agent B must be wildcarded. The wildcarded IP address and port
number enables the 'early media' capability, but results in some
insecurity, since any outside host can reach user agent A on the
enabled port number through the middlebox.
Stiemerling, Quittek, Taylor [Page 53]
Internet-Draft MIDCOM Protocol Semantics January 2004
User Agent SIP Middlebox User Agent
A Proxy NAPT B
| | | |
| INIVTE B@B.DE | | |
| SDP:m=..P_AI.. | | |
| c=IP_AI | | |
|--------------->| | |
| | | |
| | PER PID1 UDP 1 EVEN IN | |
| | IP_AI P_AI ANY ANY 300s | |
| |*****************************>| |
| |<*****************************| |
| | PER OK GID1 PID1 ANY ANY | |
| | IP_AE P_AE1 300s | |
Figure 11: PER with wildcard address and port number
A successfully PER reply, as shown in Figure 11, results in a NAT
binding at the middlebox. This binding enables UDP traffic from any
host outside of user agent A's private network to reach user agent
A. So user agent B could start sending traffic immediately after
receiving the INVITE message, and so can do any other host. Even
hosts that are not intended to be a participant, like any malicious
host.
In the case the middlebox does not support or does not permit IP
address wildcarding for security reasons, the PER request will be
rejected with an appropriate failure reason, like 'IP wildcarding not
supported'. Nevertheless, the SIP proxy server needs an outside IP
address and port number at the middlebox (the NAPT) in order to
forward the SIP INVITE message.
The IP address of user agent B is still not known yet (it will be
sent by user agent B in the SIP reply message) and IP address
wildcarding is not permitted, the SIP proxy server uses the PRR
transaction.
By using the PRR request the SIP proxy requests an outside IP address
and port number (see Figure 12) without already establishing a NAT
binding or pin hole. The PRR request contains the service parameter
'tw', i.e. the MIDCOM agent chooses the default value. In this
configuration, NAPT and no twice NAT, only an outside address is
reserved. The SIP proxy server replaces in the SDP payload of the
INVITE message the IP address and port number of user agent A by the
reserved IP address and port from PRR reply (see Figure 12). The SIP
INVITE message is forwarded to user agent B with a modified SDP body
containing the outside address and port number, to which user agent B
will send its RTP media stream.
Stiemerling, Quittek, Taylor [Page 54]
Internet-Draft MIDCOM Protocol Semantics January 2004
User Agent SIP Middlebox User Agent
A Proxy NAPT B
| | | |
...PER in Figure 11 has failed, continuing with PRR ...
| | | |
| |PRR tw v4 v4 A UDP 1 EVEN 300s| |
| |*****************************>| |
| |<*****************************| |
| | PRR OK PID1 GID1 EMPTY | |
| | IP_AE/P_AE 300s | |
| | | |
| | INVITE B@B.DE SDP:m=..P_AE.. c=IP_AE |
| |-------------------------------------------->|
| |<--------------------------------------------|
| | 200 OK SDP:m=..P_B.. c=IP_B |
Figure 12: Address reservation with PRR transaction
This SIP `200 OK' reply contains the IP address and port number, at
which user agent B will receive a media stream. The IP address is
assumed to be equal to the IP address from which user agent B will
send its media stream.
Now, the SIP proxy server has sufficient information for establishing
the complete NAT binding with a policy enable rule (PER) transaction,
i.e. the UDP/RTP data of the call can flow from user agent B to user
agent A. The PER transaction references the reservation by passing
the PID of the PRR (PID1).
For the opposite direction, UDP/RTP data from user agent A to B, has
to be enabled also. This is done by a second PER transaction with
all the necessary parameters (see figure 13). The request message
contains the group identifier (GID1) the middlebox has assigned in
the first PER transaction. Therefore, both policy rules have become
members of the same group. After having enabled both UDP/RTP streams
the SIP proxy can forward the `200 OK' SIP message to user agent A to
indicate that the telephone call can start.
Stiemerling, Quittek, Taylor [Page 55]
Internet-Draft MIDCOM Protocol Semantics January 2004
User Agent SIP Middlebox User Agent
A Proxy NAPT B
| | | |
| | PER PID1 UDP 1 SAME IN | |
| | IP_AI P_AI IP_B ANY 300s | |
| |*****************************>| |
| |<*****************************| |
| | PER OK GID1 PID1 IP_B ANY | |
| | IP_AE P_AE1 300s | |
| | | |
...media stream from user agent B to A enabled...
| | | |
| | PER GID1 UDP 1 SAME OUT | |
| | IP_AI ANY IP_B P_B 300s | |
| |*****************************>| |
| |<*****************************| |
| | PER OK GID1 PID2 IP_B P_B | |
| | IP_AE P_AE2 300s | |
| | | |
...media streams from both directions enabled...
| | | |
| 200 OK | | |
|<---------------| | |
| SDP:m=..P_B.. | | |
| c=IP_B | | |
Figure 13: Policy rule establishment for UDP flows
User agent B decides to terminate the call and sends its `BYE' SIP
message to user agent A. The SIP proxy forwards all SIP messages and
terminates the group afterwards using a group lifetime change (GLC)
transaction with a requested remaining lifetime of 0 seconds (see
Figure 14). Termination of the group includes terminating all member
policy rules.
Stiemerling, Quittek, Taylor [Page 56]
Internet-Draft MIDCOM Protocol Semantics January 2004
User Agent SIP Middlebox User Agent
A Proxy NAPT B
| | | |
| BYE | BYE |
|<---------------|<--------------------------------------------|
| | | |
| 200 OK | 200 OK |
|--------------->|-------------------------------------------->|
| | | |
| | GLC GID1 0s | |
| |*****************************>| |
| |<*****************************| |
| | GLC OK 0s | |
| | | |
...both NAT bindings for the media streams are removed...
Figure 14: Termination of Policy Rule Groups
5. Compliance with MIDCOM Requirements
This section explains the compliance of the specified semantics with
the MIDCOM requirements. It is structured according to [MDC-REQ]:
- Compliance with Protocol Machinery Requirements (Section 5.1)
- Compliance with Protocol Semantics Requirements (Section 5.2)
- Compliance with Security Requirements (Section 5.3)
The requirements are referred to using the section number they are
defined in: "requirement x.y.z" refers to the requirement specified
in section x.y.z of [MDC-REQ].
5.1. Protocol Machinery Requirements
5.1.1. Authorized Association
The specified semantics enable a MIDCOM agent to establish an
authorized association between itself and the middlebox. The agent
identifies itself by the authentication mechanism of the Session
Establishment transaction described in Section 2.2.1. Based on this
authentication the middlebox can make a determination as to whether
or not the agent will be permitted to request a service. Thus,
requirement 2.1.1 is met.
5.1.2. Agent connects to Multiple Middleboxes
As specified in Section 2.2, the MIDCOM protocol allows the agent to
communicate with more than one middlebox simultaneously. The
selection of a mechanism for separating different sessions is left to
the concrete protocol definition. It must provide a clear mapping of
protocol messages to open sessions. Then requirement 2.1.2 is met.
Stiemerling, Quittek, Taylor [Page 57]
Internet-Draft MIDCOM Protocol Semantics January 2004
5.1.3. Multiple Agents connect to same Middlebox
As specified in Section 2.2, the MIDCOM protocol allows the middlebox
to communicate with more than one agent simultaneously. The
selection of a mechanism for separating different sessions is left to
the concrete protocol definition. It must provide a clear mapping of
protocol messages to open sessions. Then requirement 2.1.3 is met.
5.1.4. Deterministic Behavior
Section 2.1.2 states, that processing a request of an agent may not
be interrupted by any request of the same or another agent. This
provides atomicity among request transactions. This avoids race
conditions resulting in an unpredictable behavior of the middlebox.
Anyway, the behavior of the middlebox can only be predictable in the
view of its administrators. In the view of an agent, the middlebox
behavior is unpredictable, because the administrator can, for example
at any time modify the authorization of the agent without the agent
being able to observe this change. Consequently, the behavior of the
middlebox is not necessarily deterministic from the point of view of
any agent.
Since predictability of the middlebox behavior is given for its
administrator, requirement 2.1.4 is met.
5.1.5. Known and Stable State
Section 2.1 states that request transactions are atomic with respect
to each other and from the point of view of an agent. All
transactions are defined clearly as state transitions that either
leave the current stable and well defined state and enter a new
stable and well defined one or that remain in the current stable and
well defined state. Section 2.1 clearly demands that intermediate
states are not stable and not reported to any agent.
Furthermore, for each state transition a message is sent to the
corresponding agent, either a reply or a notification. The agent can
uniquely map each reply to one of the requests that it sent to the
middlebox, because request agent unique request identifiers are used
for this purpose. Notifications are self-explanatory by their
definition.
Furthermore, the Group List transaction (Section 2.4.3), the Group
Status transaction (Section 2.4.4), the Policy Rule List transaction
(Section 2.3.11), and the Policy Rule Status transaction (Section
2.3.12) allow the agent at any time during a session to retrieve
information about
- all policy rule groups it may access,
- the status and member policy rules of all accessible groups,
Stiemerling, Quittek, Taylor [Page 58]
Internet-Draft MIDCOM Protocol Semantics January 2004
- all policy rules it may access,
- and the status of all accessible policy rules.
Therefore, the agent is precisely informed about the state of the
middlebox (as far as the services requested by the agent are
affected) and requirement 2.1.5 is met.
5.1.6. Status Report
As argued in the previous section, the middlebox unambiguously
informs the agent about every state transition related to any of the
services requested by the agent. Also the agent can at any time
retrieve full status information about all accessible policy rules
and policy rule groups. Thus, requirement 2.1.6 is met.
5.1.7. Unsolicited Messages (Asynchronous Notifications)
The semantics include asynchronous notifications messages from the
middlebox to the agent, including the Session Termination
Notification message, the Policy Rule Event Notification (REN)
message and the Group Event Notification (GEN) message (see Section
2.1.2). These notifications report every change of state of policy
rules or policy rule groups, that was not explicitly requested by the
agent. Thus, requirement 2.1.7 is met by the semantics specified
above.
5.1.8. Mutual Authentication
As specified in Section 2.2.1, the semantics require mutual
authentication of agent and middlebox, either by using two subsequent
Session Establishment transactions or by using mutual authentication
provided on a lower protocol layer. Thus, requirement 2.1.8 is met.
5.1.9. Session Termination by any Party
The semantics specification states in Section 2.2.2 that the agent
may request session termination by generating the Session Termination
request and that the middlebox may not reject this request. In turn,
Section 2.2.3 states that the middlebox may send the Asynchronous
Session Termination notification at any time and then terminate the
session. Thus, requirement 2.1.9 is met.
5.1.10. Request Result
Section 2.1 states that each request of an agent is followed by a
reply of the middlebox indicating either success of failure. Thus,
requirement 2.2.10 is met.
Stiemerling, Quittek, Taylor [Page 59]
Internet-Draft MIDCOM Protocol Semantics January 2004
5.1.11. Version Interworking
Section 2.2.1 states that the agent need to specify the protocol
version number which it is going to use during the session. The
middlebox may accept this and act according to this protocol version
or reject the session if it does not support this version. If the
session setup gets rejected, the agent may try again with another
version. Thus, requirement 2.2.11 is met.
5.1.12. Deterministic Handling of Overlapping Rules
The only policy rule actions specified are 'reserve' and 'enable'.
For firewalls, overlapping enable actions or reserve actions do not
create any conflict, so a firewall will always accept overlapping
rules as specified in Section 2.3.2 (assuming the required
authorization is given).
For NATs reserve and enable may conflict. If a conflicting request
arrives, it is rejected, as stated in Section 2.3.2. If an
overlapping request arrives that does not conflict with the ones it
overlaps, it is accepted (assuming the required authorization is
given).
Therefore, the behavior of the middlebox in the presence of
overlapping rules can be predicted deterministically, and requirement
2.1.12 is met.
5.2. Protocol Semantics Requirements
5.2.1. Extensible Syntax and Semantics
Requirement 2.2.1 explicitly requests extensibility of protocol
syntax. This needs to be addressed by the concrete protocol
definition. The semantics specification is extensible anyway,
because new transaction may be added.
5.2.2. Policy Rules for Different Types of Middleboxes
Section 2.3 explains that the semantics use identical transactions
for all middlebox types and that the same policy rule can be applied
to all of them. Thus requirement 2.2.2 is met.
5.2.3. Ruleset Groups
The semantics explicitly supports grouping of policy rules and
transactions on policy rule groups, as described in Section 2.4. The
group transactions can be used for lifetime extension and termination
of all policy rules being member of the particular group. Thus,
requirement 2.2.3 is met.
Stiemerling, Quittek, Taylor [Page 60]
Internet-Draft MIDCOM Protocol Semantics January 2004
5.2.4. Policy Rule Lifetime Extension
The semantics include a transaction for explicit lifetime extension
of policy rules, as described in Section 2.3.3. Thus requirement
2.2.4 is met.
5.2.5. Robust Failure Modes
The state transitions at the middlebox are clearly specified and
communicated to the agent. There is no intermediate state reached by
a partial processing of a request. All requests are always processed
completely, either successful or unsuccessful. All request
transaction include a list of failure reasons. These failure reasons
cover indication of invalid parameters where applicable. In case of
failure one of the specified reasons is returned from the middlebox
to the agent. Thus requirement 2.2.5 is met.
5.2.6. Failure Reasons
The semantics include a failure reason parameter in each failure
reply. Thus requirement 2.2.6 is met.
5.2.7. Multiple Agents Manipulating Same Policy Rule
As specified in Sections 2.3 and 2.4, each installed policy rule and
policy rule group has an owner, which is the authenticated agent that
created the policy rule or group, respectively. The authenticated
identity is input to authorization of access to policy rules and
groups.
If the middlebox is sufficiently configurable, its administrator can
configure it such that one authenticated agent is authorized to
access and modify policy rules and groups owned by another agent.
Because specified semantics does not preclude this, it meets
requirement 2.2.7.
5.2.8. Carrying Filtering Rules
The Policy Enable Rule transaction specified in Section 2.3.8 can
carry 5-tuple filtering rules. It meets requirement 2.2.8.
5.2.9. Parity of Port Numbers
As specified in Section 2.3.6, the agent is able to request keeping
the port parity when reserving port numbers with the PRR transaction
(see Section 2.3.8) and when establishing address bindings with the
PER transaction (see Section 2.3.9). Thus requirement 2.2.9 is met.
Stiemerling, Quittek, Taylor [Page 61]
Internet-Draft MIDCOM Protocol Semantics January 2004
5.2.10. Consecutive Range of Port Numbers
As specified in Section 2.3.6, the agent is able to request a
consecutive range of port numbers when reserving port numbers with
the PRR transaction (see Section 2.3.8) and when establishing address
bindings or pinholes with the PER transaction (see Section 2.3.9).
Thus requirement 2.2.10 is met.
5.2.11. Contradicting Overlapping Policy Rules
Requirement 2.2.11 is based on the assumption that contradicting
policy rule actions, such as 'enable'/'allow' and
'disable'/'disallow' are supported. In conformance with decisions
made by the working group after finalizing the requirements document,
this requirement is not met by the semantics, because no
'disable'/'disallow' action is supported.
5.3. Security Requirements
5.3.1. Authentication, Confidentiality, Integrity
The semantics definition support mutual authentication of agent and
middlebox in the Session Establishment transaction (Section 2.2.1).
The use of an underlying protocol like TLS or IPSEC is mandatory.
Thus requirement 2.3.1 is met.
5.3.2. Optional Confidentiality of Control Messages
The use of IPSEC or TLS allows agent and middlebox to use an
encryption method (including no encryption). Thus requirement 2.3.2
is met.
5.3.3. Operation across Un-trusted Domains
Operation across untrusted domains is supported by mutual
authentication and by the use of TLS and IPSEC. Thus requirement
2.3.3 is met.
5.3.4. Mitigate Replay Attacks
The specified semantics mitigates replay attacks and meets
requirement 2.3.4 by requiring mutual authentication of agent and
middlebox, and by mandating the use of TLS or IPSEC encryption.
Further mitigation can be provided as part of a concrete MIDCOM
protocol definition, for example by requiring consecutively
increasing numbers for request identifiers.
Stiemerling, Quittek, Taylor [Page 62]
Internet-Draft MIDCOM Protocol Semantics January 2004
6. Security Considerations
The interaction between a middlebox and an agent is (see [MDC-FRM]) a
very sensitive point with respect to security. The configuration of
policy rules from a middlebox external entity appears to be
contradicting the nature of a middlebox. Therefore, effective means
have to be used to ensure:
- mutual authentication between agent and middlebox
- authorization
- message integrity
- message confidentiality
The semantics define a mechanism to ensure mutual authentication
between agent and middlebox (see section 2.2.1). In combination with
the authentication, the middlebox is able to decide whether an agent
is authorized to request an action at the middlebox or not. The
semantics rely on underlying protocols, like TLS or IPSEC, to keep
the message integrity and confidentiality of the transferred data
between both entities.
For the TLS and IPSEC use, both sides must use securely-configured
credentials for authentication and authorization.
The configuration of policy rules with wildcarded IP addresses and
port numbers results in certain risks, like opening too much
wildcarded policy rules. A too much wildcarded policy rule is A0 and
A3 with IP address set to 'any' IP address for instance. This type
of pin-hole would render the middlebox, in the sense of security,
useless, since any packet can traverse the middlebox without further
checking. The local policy of the middlebox should reject such policy
rule enable requests. A reasonable default configuration for
wildcarding would be that only one port number may be wildcarded and
all IP addresses must be set without wildcarding. Depending on the
particular application this could be too strict, e.g. SIP.
7. IAB Considerations on UNSAF
UNilateral Self-Address Fixing (UNSAF) is described in [RFC3424] as
process at originating endpoints that attempt to determine or fix the
address (and port) by which it is known to another endpoint. UNSAF
proposals, like STUN [RFC3489], are considered as a general class of
workarounds for NAT traversal and as solutions for scenarios with no
middlebox communication (MIDCOM).
This document describes the protocol semantics for such a middlebox
communication (MIDCOM) solution. MIDCOM is not intended as short
term workaround, but more as long term solution for middlebox
communication. In MIDCOM, endpoints are not involved in allocating,
Stiemerling, Quittek, Taylor [Page 63]
Internet-Draft MIDCOM Protocol Semantics January 2004
maintaining, and deleting addresses and ports at the middlebox. The
full control of addresses and ports at the middlebox is located at
the MIDCOM server.
Therefore, the UNSAF considerations of [RFC2424] do not apply.
8. Acknowledgments
We like to thank all the people contributing to the semantics
discussion on the mailing list for a lot of valuable comments.
Stiemerling, Quittek, Taylor [Page 64]
Internet-Draft MIDCOM Protocol Semantics January 2004
9. Normative References
[MDC-FRM] Srisuresh, P., Kuthan, J., Rosenberg, J., Molitor, A.,
Rayhan, A., "Middlebox Communication Architecture and
Framework", RFC 3303, August 2002
[MDC-REQ] Swale, R.P., Mart, P.A., Sijben, P., Brimm, S., Shore, M.,
"Middlebox Control (MIDCOM) Protocol Architecture and
Requirements", RFC 3304, August 2002
[NAT-TERM] Srisuresh,P., and Holdrege, M., "IP Network Translator (NAT)
Terminology and Considerations", RFC 2663, August 1999.
[NAT-TRAD] Srisuresh,P., and Egevang, K., "Traditional IP Network
Address Translator (Traditional NAT)", RFC 3022, January
2001
10. Informative References
[RFC3198] Westerinen, A. et al., "Terminology for Policy-Based
Management", RFC 3198, November 2001.
[RFC2246] Dierks, T., Allen, C., "The TLS Protocol Version 1.0", RFC
2246, January 1999.
[RFC2402] Kent, S., and Atkinson, R., "IP Authentication Header", RFC
2402, November 1998.
[RFC2406] Kent, S., and Atkinson, R., "IP Encapsulating Security
Payload (ESP)", RFC 2406, November 1998.
[RFC3424] Daigle, L., "IAB Considerations for UNilateral Self-Address
Fixing (UNSAF) Across Network Address Translation", RFC
3424, November 2002
[RFC3489] Rosenberg, J., et al., "STUN - Simple Traversal of User
Datagram Protocol (UDP) Through Network Address Translators
(NATs)", RFC 3489, March 2003
11. Authors' Addresses
Martin Stiemerling
NEC Europe Ltd.
Network Laboratories
Kurfuersten-Anlage 36
69115 Heidelberg
Germany
Stiemerling, Quittek, Taylor [Page 65]
Internet-Draft MIDCOM Protocol Semantics January 2004
Phone: +49 6221 90511-13
Email: stiemerling@netlab.nec.de
Juergen Quittek
NEC Europe Ltd.
Network Laboratories
Kurfuersten-Anlage 36
69115 Heidelberg
Germany
Phone: +49 6221 90511-15
EMail: quittek@netlab.nec.de
Tom Taylor
Nortel Networks
1852 Lorraine Ave.
Ottawa, Ontario
Canada K1H 6Z8
Phone: +1 613 736 0961
Email: taylor@nortelnetworks.com
12. Full Copyright Statement
Copyright (C) The Internet Society (2004). All Rights Reserved.
This document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain it
or assist in its implementation may be prepared, copied, published
and distributed, in whole or in part, without restriction of any
kind, provided that the above copyright notice and this paragraph are
included on all such copies and derivative works. However, this
document itself may not be modified in any way, such as by removing
the copyright notice or references to the Internet Society or other
Internet organizations, except as needed for the purpose of
developing Internet standards in which case the procedures for
copyrights defined in the Internet Standards process must be
followed, or as required to translate it into languages other than
English.
The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an
"AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
Stiemerling, Quittek, Taylor [Page 66]
Internet-Draft MIDCOM Protocol Semantics January 2004
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Stiemerling, Quittek, Taylor [Page 67]