J. Kempf,
Editor
Internet Draft K. Leung
Document: draft-ietf-netlmm-nohost-req-00.txt P. Roberts
K. Nishida
G. Giaretta
M. Liebsch
Expires: August, 2006 Feburary, 2006
Requirements and Gap Analysis for IP Local Mobility
(draft-ietf-netlmm-nohost-req-00.txt)
Status of this Memo
By submitting this Internet-Draft, each author represents that any
applicable patent or other IPR claims of which he or she is aware have been
or will be disclosed, and any of which he or she becomes aware will be
disclosed, in accordance with Section 6 of BCP 79.
Internet-Drafts are working documents of the Internet Engineering Task Force
(IETF), its areas, and its working groups. Note that other groups may also
distribute working documents as Internet-Drafts.
Internet-Drafts are draft documents valid for a maximum of six months and
may be updated, replaced, or obsoleted by other documents at any time. It is
inappropriate to use Internet-Drafts as reference material or to cite them
other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
Abstract
In draft-kempf-netlmm-nohost-ps, the problems with using global IP mobility
management protocols for local mobility and some problems with existing
localized mobility management protocols are described. In this document, we
explore requirements for localized mobility management in more detail. An
extensive gap analysis against the protocols illustrates where existing
protocols are able to fulfill the requirements and where they are lacking.
Table of Contents
1.0 Introduction.....................................................2
2.0 Requirements for Localized Mobility Management...................3
3.0 Gap Analysis.....................................................8
4.0 Security Considerations.........................................18
5.0 Recommendation..................................................18
6.0 Author Information..............................................19
Kempf, et. al. Expires August, 2006 [Page 1]
Internet Draft LMM Requirements and Gap Analysis Feburary, 2006
7.0 Informative References..........................................20
8.0 IPR Statements..................................................21
9.0 Disclaimer of Validity..........................................22
10.0 Copyright Notice................................................22
11.0 Changes in 01 (remove before publication).......................22
1.0 Introduction
In draft-kempf-netlmm-nohost-ps [1], the basic problems that occur when a
global mobility protocol is used for managing local mobility are described,
and two basic approaches to localized mobility management - the host-based
approach that is used by most IETF protocols and the WLAN switch approach -
are examined. The conclusion from the problem statement document is that
neither approach has a complete solution to the problem. While the WLAN
switch approach is most convenient for network operators and users because
it requires no mobile node support, the proprietary nature limits
interoperability and the restriction to a single wireless link type and
wired backhaul link type restricts scalablity. The IETF host-based protocols
require host software stack changes that may not be compatible with all
global mobility protocols, and also require specialized and complex security
transactions with the network that may limit deployability.
This document develops more detailed requirements for a localized mobility
management protocol and analyzes existing protocols against those
requirements. In Section 2.0, we review a list of requirements that are
desirable in a localized mobility management solution. Section 3.0 performs
a gap analysis against the requirements of proposed solutions to localized
mobility management. Section 4.0 briefly outlines security considerations.
Finally, in Section 5.0, a recommendation is made for the development of a
network-based approach to localized mobility management.
1.1 Terminology
Mobility terminology in this draft follows that in RFC 3753 [2] and in [2].
In addition, the following terms are used here:
Node
A node can be either an end host or router that is served by the
localized mobility management domain. Such a node may perform global
mobility management (e.g. NEMO [3] or MIPv6[5]). In this case, the IP
address obtained by the node from the localized mobility management
domain is the care-of address.
Host-Based Approach
A host-based approach to localized mobility management requires binding
between a local care-of address and a regional care-of address at a
mobility anchor within the localized mobility management domain. The
binding is maintained by the mobile node and requires software in the
mobile node's stack to perform the binding. The localized mobility
service is authorized with the mobility anchor point separately from
network access. An example is HMIPv6 [20]. A mobility anchor is a kind
Kempf, et. al. Expires August 2006 [Page 2]
Internet Draft LMM Requirements and Gap Analysis Feburary, 2006
of localized mobility management domain gateway. The regional care-of
address is fixed at the mobility anchor while the local care-of address
on the access router changes when the mobile node moves to a new IP
link.
Micromobility Approach
A micromobility approach to localized mobility management requires host
route propagation from the mobile node to a collection of specialized
routers in the localized mobility management domain along a path back
to a boundary router at the edge of the localized mobility management
domain. A boundary router is a kind of localized mobility management
domain gateway. Localized mobility management is authorized with the
access router, but reauthorization with each new access router is
necessary on IP link movement, in addition to any reauthorization for
basic network access. The host routes allow the mobile node to maintain
the same IP address when it moves to a new IP link, and still continue
to receive packets on the new IP link.
Edge Mobility Approach
In the edge mobility approach to localized mobility management, the
access routers update bindings between the mobile node's care-of
address and the mobile node's current IP link. The bindings are
maintained at an edge mobility anchor point. The mobile node is not
involved in localized mobility management beyond movement detection.
The mobile node requires no special authorization for localized
mobility management service beyond the authorization required for basic
network access. A mobile node's IP address does not change when the
mobile node moves from one access router to another within the coverage
area of the edge mobility anchor point, because the mobility anchor and
access routers take care of changing the routing.
2.0 Requirements for Localized Mobility Management
Any localized mobility solution must naturally address the three problems
described in [1]. In addition, the side effects of introducing such a
solution into the network need to be limited. In this section, we address
requirements on a localized mobility solution including both solving the
basic problems and limiting the side effects.
Some basic requirements of all IETF protocols are not discussed in detail
here, but any solution is expected to satisfy them. These requirements are
interoperability, scalability, and minimal requirement for specialized
network equipment. A good discussion of their applicability to IETF
protocols can be found in [4].
Out of scope for the initial requirements discussion are QoS, multicast, and
dormant mode/paging. While these are important functions for mobile nodes,
they are not part of the base localized mobility management problem. In
addition, mobility between localized mobility management domains is not
covered here. It is assumed that this is covered by the global mobility
management protocols.
Kempf, et. al. Expires July 2006 [Page 3]
Internet Draft LMM Requirements and Gap Analysis Feburary, 2006
2.1 Handover Performance Improvement (Requirement #1)
Handover packet loss occurs because there is usually latency between when
the wireless link handover starts and when the IP link handover completes.
During this time the mobile node is unreachable at its former topological
location on the old IP link where correspondents are sending packets and to
which the routing system is routing them. Such misrouted packets are
dropped. This aspect of handover performance optimization has been the
subject of an enormous amount of work, both in other SDOs, to reduce the
latency of wireless link handover, and in the IETF and elsewhere, to reduce
the latency in IP link handover. Many solutions to this problem have been
proposed at the wireless link layer and at the IP layer. One aspect of this
requirement for localized mobility management is that the processing delay
for changing the routing after handover must be minimal, in order to avoid
excessive packet loss. Ideally, if network-side link layer support is
available for handling movement detection, the routing update should
complete within the time required for wireless link handover.
Note that a related problem occurs when traffic packets are not routed
through a global mobility anchor such as a Mobile IP home agent. Route
optimized Mobile IPv6 [5] and HIP [6] are examples. A loss of connectivity
can occur when both sides of the IP conversation are mobile and they both
hand over at the same time. The two sides must use a global mobility anchor
point, like a home agent or rendezvous server, to re-establish the
connection, but there may be substantial packet loss until the problem is
discovered. Another aspect of this requirement is that the solution must
ensure that connectivity is not lost when both ends are mobile and move at
the same time.
In both cases, the loss of accurate routing caused the connection to
experience an interruption which may cause service degradation for real time
traffic such as voice
2.2 Reduction in Handover-related Signaling Volume (Requirement #2)
Considering Mobile IPv6 as the global mobility protocol (other mobility
protocols require about the same or somewhat less), if a mobile node is
required to reconfigure on every move between IP links, the following set of
signaling messages must be done:
1) Movement detection using DNA [7] or possibly a link specific protocol,
2) Any link layer or IP layer AAA signaling, such as 802.1x [8] or PANA [9].
The mobile node may also or instead have to obtain a router certificate
using SEND [10], if the certificate is not already cached,
3) Router discovery which may be part of movement detection,
4) If stateless address autoconfiguration is used, address configuration and
Duplicate Address Detection (unless optimistic Duplicate Address
Detection [11] is used). If stateful address configuration is used, then
DHCP is used for address configuration,
5) Binding Update to the home agent,
6) If route optimization is in effect, return routability to establish the
binding key,
Kempf, et. al. Expires July 2006 [Page 4]
Internet Draft LMM Requirements and Gap Analysis Feburary, 2006
7) Binding Update to correspondent nodes for route optimization.
Note that Steps 1-2 will always be necessary, even for intra-link mobility,
and Step 3 will be necessary even if the mobile node's care-of address can
remain the same when it moves to a new access router.
This is a lot of signaling just to get up on a new IP link. Furthermore, in
some cases, the mobile node may need to engage in "heartbeat signaling" to
keep the connection with the correspondent or global mobility anchor fresh,
for example, return routability in Mobile IPv6 must be done at a maximum
every 7 minutes even if the mobile node is standing still. The requirement
is that handover signaling volume from the localized mobility management
protocol should be no more than what is needed to securely redirect a mobile
node's traffic within the localized mobility management domain.
2.3 Location privacy (Requirement #3)
Location privacy in the context of IP mobility refers to hiding the
geographic location of mobile users. Although general location privacy
issues have been discussed in [13], the location privacy referred to here
focuses on the IP layer and involves the basic property of the IP address
that may change due to the mobility. The location information should not be
revealed to nor deduced by the correspondent node without the authorization
of the mobile node's owner. Since the localized mobility management protocol
is responsible for the mobile node's mobility within the local mobility management
domain, it should conceal geographical movement of the mobile node.
The threats to location privacy come in a variety of forms. Perhaps least
likely is a man in the middle attack in which traffic between a
correspondent and the mobile node is intercepted and the mobile node's
location is deduced from that, since man in the middle attacks in the
Internet tend to be fairly rare. More likely are attacks in which the
correspondent is the attacker or the correspondent or even mobile node
itself are relaying information on the care-of address change to someone.
The owner of the correspondent or mobile node might not even be aware of the
problem if an attacker has installed spyware or some other kind of exploit
on the mobile node and the malware is relaying the change in care-of address
to an attacker.
Note that the location privacy referred to here is different from the
location privacy discussed in [15][16][17]. The location privacy discussed
in these drafts primarily concerns modifications to the Mobile IPv6 protocol
to eliminate places where an eavesdropper could track the mobile node's
movement by correlating home address and care of address.
The requirement is that the location information should not be revealed to
nor deduced by the correspondent node without the authorization of the
mobile node's owner as long as the mobile node remains within the localized
mobility management domain. Since the localized mobility management protocol
is responsible for the mobile node mobility within the localized mobility
management domain, it should conceal the geographical movement of the mobile
node.
Kempf, et. al. Expires July 2006 [Page 5]
Internet Draft LMM Requirements and Gap Analysis Feburary, 2006
2.4 Efficient Use of Wireless Resources (Requirement #4)
Advances in wireless PHY and MAC technology continue to increase the
bandwidth available from limited wireless spectrum, but even with technology
increases, wireless spectrum remains a limited resource. Unlike wired
network links, wireless links are constrained in the number of bits/Hertz by
their coding technology and use of physical spectrum, which is fixed by the
PHY. It is not possible to lay an extra cable if the link becomes
increasingly congested as is the case with wired links.
Some existing localized mobility management solutions increase packet size
over the wireless link by adding tunneling or other per packet overhead.
While header compression technology can remove header overhead, header
compression does not come without cost. Requiring header compression on the
wireless access points increases the cost and complexity of the access
points, and increases the amount of processing required for traffic across
the wireless link. Since the access points tend to be a critical bottleneck
in wireless access networks for real time traffic (especially on the
downlink), reducing the amount of per-packet processing is important. While
header compression probably cannot be completely eliminated, especially for
real time media traffic, simplifying compression to reduce processing cost
is an important requirement.
The requirement is that the localized mobility management protocol should
not introduce any new signaling or increase existing signaling over the air.
2.5 Reduction of Signaling Overhead in the Network (Requirement #5)
While bandwidth and router processing resources are typically not as
constrained in the wired network, wired networks tend to have higher
bandwidth and router processing constraints than the backbone. These
constraints are a function of the cost of laying fiber or wiring to the
wireless access points in a widely dispersed geographic area. Therefore, any
solutions for localized mobility management should minimize signaling within
the wired network as well.
2.6 No Extra Security Between Mobile Node and Network (Requirement #6)
Localized mobility management protocols that have signaling between the
mobile node and network require a security association between the mobile
node and the network entity that is the target of the signaling.
Establishing a security association specifically for localized mobility
service in a roaming situation may prove difficult, because provisioning a
mobile node with security credentials for authenticating and authorizing
localized mobility service in each roaming partner's network may be
unrealistic from a deployment perspective. Reducing the complexity of mobile
node to network security for localized mobility management can therefore
reduce barriers to deployment.
Removing mobile node involvement in localized mobility management also
limits the possibility of DoS attacks on network infrastructural elements.
Kempf, et. al. Expires July 2006 [Page 6]
Internet Draft LMM Requirements and Gap Analysis Feburary, 2006
In a host based approach, the mobile node is required to have a global or
restricted routing local IP address for a network infrastructure element,
the mobility anchor point. The network infrastructural element therefore
becomes a possible target for DoS attacks, even if mobile nodes are properly
authenticated. A properly authenticated mobile node can either willfully or
inadvertently give the network infrastructural element address to an
attacker.
In summary, ruling out mobile node involvement in local mobility management
simplifies security by removing the need for service-specific credentials to
authenticate and authorize the mobile node for localized mobility management
in the network and by limiting the possibility of DoS attacks on network
infrastructural elements. The requirement is that support for localized
mobility management should not require additional security between the
mobile node and the network.
2.7 Support for Heterogeneous Wireless Link Technologies (Requirement #7)
The number of wireless link technologies available is growing, and the
growth seems unlikely to slow down. Since the standardization of a wireless
link PHY and MAC is a time consuming process, reducing the amount of work
necessary to interface a particular wireless link technology to an IP
network is necessary. A localized mobility management solution should
ideally require minimal work to interface with a new wireless link
technology.
In addition, an edge mobility solution should provide support for multiple
wireless link technologies within the network in separate subnets. It is not
required that the localized mobility management solution support handover
from one wireless link technology to another without change in IP address.
The reason is because a change in network interface typically requires that
the hardware interface associated with one wireless link technology be
brought up and configured, and this process typically requires that the IP
stack for the new interface card be configured on the mobile node from the
driver up. Requiring that the mobile node IP stack circumvent this process
to keep the IP address constant would be a major change in the way the IP
stack software is implemented.
The requirement is that the localized mobility management protocol should
not use any wireless link specific information for basic routing management,
though it may be used for other purposes, such as identifying a mobile node.
2.8 Support for Unmodified Mobile Nodes (Requirement #8)
In the wireless LAN switching market, no modification of the software on the
mobile node is required to achieve "IP mobility" (which means localized
mobility management). Being able to accommodate unmodified mobile nodes
enables a service provider to offer service to as many customers as
possible, the only constraint being that the customer is authorized for
network access.
Kempf, et. al. Expires July 2006 [Page 7]
Internet Draft LMM Requirements and Gap Analysis Feburary, 2006
Another advantage of minimizing mobile node software for localized mobility
management is that multiple global mobility management protocols can be
supported with a localized mobility management solution that does not have
mobile node involvement. While Mobile IPv6 is clearly the global mobility
management protocol of primary interest going forward, there are a variety
of global mobility management protocols that might also need support,
including proprietary protocols needing support for backward compatibility
reasons. Within IETF, both HIP and Mobike are likely to need support in
addition to Mobile IPv6, and Mobile IPv4 support may also be necessary.
Note that this requirement does NOT mean that the mobile node has no
software at all associated with mobility or wireless. The mobile node must
have some kind of global mobility protocol if it is to move from one domain
of edge mobility support to another, although no global mobility protocol is
required if the mobile node only moves within the coverage area of the
localized mobility management protocol. Also, every wireless link protocol
requires handover support on the mobile node in the physical and MAC layers,
typically in the wireless interface driver. Information passed from the MAC
layer to the IP layer on the mobile nodenode may be necessary to trigger IP
signaling for IP link handover. Such movement detection support at the IP
level may be required in order to determine whether the mobile node's
default router is still reachable after the move to a new access point has
occurred at the MAC layer. Whether or not such support is required depends
on whether the MAC layer can completely hide link movement from the IP
layer. For a wireless link protocol such as the 3G protocols, the mobile
node and network undergo an extensive negotiation at the MAC layer prior to
handover, so it may be possible to trigger routing update without any IP
protocol involvement. However, for a wireless link protocol such as IEEE
802.11 in which there is no network involvement in handover, IP layer
movement detection signaling from the mobile node may be required to trigger
routing update.
The requirement is that the localized mobility management solution should be
able to support any mobile node that walks up to the link and has a wireless
interface that can communicate with the network, without requiring localized
mobility management software on the mobile node.
2.9 Support for IPv4 and IPv6 (Requirement #9)
While most of this document is written with IPv6 in mind, localized mobility
management is a problem in IPv4 networks as well. A solution for localized
mobility that works for both versions of IP is desirable, though the actual
protocol may be slightly different due to the technical details of how each
IP version works. From Requirement #8 (Section 2.8), minimizing mobile node
support for localized mobility means that ideally no IP version-specific
changes would be required on the mobile node for localized mobility, and
that global mobility protocols for both IPv4 and IPv6 should be supported.
Any IP version-specific features would be confined to the network protocol.
3.0 Gap Analysis
Kempf, et. al. Expires July 2006 [Page 8]
Internet Draft LMM Requirements and Gap Analysis Feburary, 2006
This section discusses a gap analysis between existing proposals for solving
localized mobility management and the requirements in Section. 2.0.
3.1 Mobile IPv6 with Local Home Agent
One option is to deploy Mobile IPv6 with a locally assigned home agent in
the local network. This solution requires the mobile node to somehow be
assigned a home agent in the local network when it boots up. This home agent
is used instead of the home agent in the home network. The advantage of this
option is that the no special solution is required for edge mobility - the
mobile node reuses the global mobility management protocol for that purpose
- if the mobile node is using Mobile IPv6. One disadvantage is that Mobile
IP has no provision for handover between home agents. Although such handover
should be infrequent, it could be quite lengthy and complex.
The analysis of this approach against the requirements above is the
following.
Requirement #1: If the mobile node does not perform route optimization, this
solution reduces, but does not eliminate, IP link handover related
performance problems.
Requirement #2: Similarly to Requirement #1, signaling volume is reduced if
no route optimization signaling is done on handover.
Requirement #3: Location privacy is preserved for external correspondents,
but the mobile node itself still maintains a local care-of address which a
worm or other exploit could misuse. If the mobile node does perform route
optimization, location privacy may be compromised, and this solution is no
better than having a remote home agent.
Requirement #4: If traffic is not route optimized, the mobile node still
pays for an over-the-air tunnel to the locally assigned home agent. The
overhead here is exactly the same as if the mobile node's home agent in the
home network is used and route optimization is not done.
Requirement #5: If the localized mobility management domain is large, the
mobile node may suffer from unoptimzed routes since handover and mobility
between home agents is not supported.
Requirement #6: A local home agent in a roaming situation requires the guest
mobile node to have the proper credentials to authenticate with the local
home agent in the serving network. In addition, as in Requirement #3, the
local home agent's address could become the target of a DoS attack if
revealed to an attacker. So a local home agent would provide no benefit for
this requirement.
Requirement #7: This solution supports multiple wireless technologies in
separate IP link subnets. No special work is required to interface a local
home agent to different wireless technologies.
Kempf, et. al. Expires July 2006 [Page 9]
Internet Draft LMM Requirements and Gap Analysis Feburary, 2006
Requirement #8: The mobile node must support Mobile IPv6 in order for this
option to work. So mobile node changes are required and other IP mobility
protocols are not supported.
Requirement #9: This solution requires separate locally assigned home agents
for Mobile IPv4 and Mobile IPv6 since the local home agent should have MIP
functions or IPv4 or IPv6 in conjunction with IP version of global mobility
protocol, or some way to register an IPv4 care of address to home address
mapping in an Mobile IPv6 home agent. While there are a couple of proposals
currently active in the IETF for this (see [18] for one), it is not clear at
this point whether they will be adopted for standards track development.
3.2 Hierarchical Mobile IPv6 (HMIPv6)
HMIPv6 [20] provides the most complete localized mobility management
solution available today as an Internet RFC. In HMIPv6, a localized mobility
anchor called a MAP serves as a routing anchor for a regional care-of
address. When a mobile node moves from one access router to another, the
mobile node changes the binding between its regional care-of address and
local care-of address at the MAP. No global mobility management signaling is
required, since the care-of address seen by correspondents does not change.
This part of HMIPv6 is similar to the solution outlined in Section 3.1;
however, HMIPv6 also allows a mobile node to hand over between MAPs.
Handover between MAPs and MAP discovery requires configuration on the
routers. MAP addresses are advertised by access routers. Handover happens by
overlapping MAP coverage areas so that, for some number of access routers,
more than one MAP may be advertised. Mobile nodes need to switch MAPs in the
transition area, and then must perform global mobility management update and
route optimization to the new regional care-of address, if appropriate.
The analysis of this approach against the requirements above is the
following.
Requirement #1 This solution shortens, but does not eliminate, the latency
associated with IP link handover, since it reduces the amount of signaling
and the length of the signaling paths.
Requirement #2 Signaling volume is reduced simply because no route
optimization signaling is done on handover within the coverage area of the
MAP.
Requirement #3 Location privacy is preserved for external correspondents,
but the mobile node itself still maintains a local care-of address which a
worm or other exploit could access by sending the local care-of address to
third malicious node to enable it to track the mobile node's location.
Requirement #4 The mobile node always pays for an over-the-air tunnel to the
MAP. If the mobile node is tunneling through a global home agent or VPN
gateway, the wired link experiences double tunneling. Over-the-air tunnel
overhead can be removed by header compression, however.
Kempf, et. al. Expires July 2006 [Page 10]
Internet Draft LMM Requirements and Gap Analysis Feburary, 2006
Requirement #5 From Requirement #1 and Requirement #4, the signaling
overhead is no more or less than for mobile nodes whose global mobility
management anchor is local. However, because MAP handover is possible,
routes across large localized mobility management domains can be improved
thereby improving wired network resource utilization by using multiple MAPs
and handing over, at the expense of the configuration and management
overhead involved in maintaining multiple MAP coverage areas.
Requirement #6 In a roaming situation, the guest mobile node must have the
proper credentials to authenticate with the MAP in the serving network. In
addition, since the mobile node is required to have a unicast address for
the MAP that is either globally routed or routing restricted to the local
administrative domain, the MAP is potentially a target for DoS attacks
across a wide swath of network topology.
Requirement #7 This solution supports multiple wireless technologies in
separate IP link subnets.
Requirement #8 This solution requires modification to the mobile nodes. In
addition, the HMIPv6 design has been optimized for Mobile IPv6 mobile nodes,
and is not a good match for other global mobility management protocols.
Requirement #9 Currently, there is no IPv4 version of this protocol;
although there is an expired Internet draft with a design for a regional
registration protocol for Mobile IPv4 that has similar functionality.
3.3 Combinations of Mobile IPv6 with Optimizations
One approach to local mobility that has received much attention in the past
and has been thought to provide a solution is combinations of protocols. The
general approach is to try to cover gaps in the solution provided by MIPv6
by using other protocols. In this section, gap analyses for MIPv6 + FMIPv6
and HMIPv6 + FMIPv6 are discussed.
3.3.1 MIPv6 + FMIPv6
As discussed in Section 3.1, the use of MIPv6 with a dynamically assigned,
local home agent cannot fulfill the requirements. A fundamental limitation
is that Mobile IPv6 cannot provide seamless handover (i.e. Requirement #1).
FMIPv6 has been defined with the intent to improve the handover performance
of MIPv6. For this reason, the combined usage of FMIPv6 and MIPv6 with a
dynamically assigned local home agent has been proposed to handle local
mobility.
Note that this gap analysis only applies to localized mobility management,
and it is possible that MIPv6 and FMIPv6 might still be acceptable for
global mobility management.
The analysis of this combined approach against the requirements follows.
Requirement #1 FMIPv6 provides a solution for handover performance
improvement that should fulfill the requirements raised by real-time
Kempf, et. al. Expires July 2006 [Page 11]
Internet Draft LMM Requirements and Gap Analysis Feburary, 2006
applications in terms of jitter, delay and packet loss. The location of the
home agent (in local or home domain) does not affect the handover latency.
Requirement #2 FMIPv6 requires the mobile node to perform extra signaling with the
access router (i.e. exchange of RtSolPr/PrRtAdv and FBU/FBA). Moreover, as
in standard MIPv6, whenever the mobile node moves to another IP link, it
must send a Binding Update to the home agent. If route optimization is used,
the mobile node also performs return routability and sends a Binding Update
to each correspondent node. Nonetheless, it is worth noting that FMIPv6
should result in a reduction of the amount of IPv6 Neighbor Discovery
signaling on the new link.
Requirement #3 The mobile node mantains a local care-of address. If route
optimization is not used, location privacy can be achieved using bi-
directional tunneling. However, as mentioned in Section 3.1, a worm or other
malware can exploit this care of address by sending it to a third malicious
node.
Requirement #4 As stated for Requirement #2, the combination of MIPv6 and
FMIPv6 generates extra signaling overhead. For data packets, in addition to
the Mobile IPv6 over-the-air tunnel, there is a further level of tunneling
between the mobile node and the previous access router during handover. This
tunnel is needed to forward incoming packets to the mobile node addressed to
the previous care-of address. Another reason is that, even if the mobile
node has a valid new care-of address, the mobile node cannot use the new
care of address directly with its correspondents without performing route
optimization to the new care of address. This implies that the transient
tunnel overhead is in place even for route optimized traffic.
Requirement #5 FMIPv6 generates extra signaling overhead between previous
the access router and the new access router for the HI/HAck exchange.
Concerning data packets, the use of FMIPv6 for handover performance
improvement implies a tunnel between the previous access router and the
mobile node that adds some overhead in the wired network. This overhead has
more impact on star topology deployments, since packets are routed down to
the old access router, then back up to the aggregation router and then back
down to the new access router.
Requirement #6 In addition to the analysis for Mobile IPv6 with local home
agent in Section 3.1, FMIPv6 requires the mobile node and the previous
access router to share a security association in order to secure FBU/FBA
exchange. So far, only a SEND-based solution has been proposed and this
requires the mobile node to use autoconfigured Cryptographically Generated Addresses
(CGAs)[21]. This precludes stateful address allocation using DHCP, which
might be a necessary deployment in certain circumstances. Another solution
based on AAA is under study but it could require extra signaling overhead
over the air and in the wired network and it could raise performance issues.
Requirement #7 MIPv6 and FMIPv6 support multiple wireless technologies, so
this requirement is fufilled.
Kempf, et. al. Expires July 2006 [Page 12]
Internet Draft LMM Requirements and Gap Analysis Feburary, 2006
Requirement #8 The mobile node must support both MIPv6 and FMIPv6, so it is
not possible to satisfy this requirement.
Requirement #9 Work is underway to extend MIPv6 with the capability to run
over both IPv6-enabled and IPv4-only networks [18]. FMIPv6 only supports
IPv6. Even though an IPv4 version of FMIP has been recently proposed, it is
not clear how it could be used together with FMIPv6 in order to handle fast
handovers across any wired network.
3.3.2 HMIPv6 + FMIPv6
HMIPv6 provides several advantages in terms of local mobility management.
However, as seen in Section 3.2, it does not fulfill all the requirements
identified in Section 2.0. In particular, HMIPv6 does not completely
eliminate the IP link handover latency. For this reason, FMIPv6 could be
used together with HMIPv6 in order to cover the gap.
Note that even if this solution is used, the mobile node is likely to need
MIPv6 for global mobility management, in contrast with the MIPv6 with
dynamically assigned local home agent + FMIPv6 solution. Thus, this solution
should really be considered MIPv6 + HMIPv6 + FMIPv6.
The analysis of this combined approach against the requirements follows.
Requirement #1 HMIPv6 and FMIPv6 both shorten the latency associated with IP
link handovers. In particular, FMIPv6 is expected to fulfill the
requirements on jitter, delay and packet loss raised by real-time
applications.
Requirement #2 Both FMIPv6 and HMIPv6 require extra signaling compared with
Mobile IPv6. As a whole the mobile node performs signaling message exchanges
at each handover that are RtSolPr/PrRtAdv, FBU/FBA, LBU/LBA and BU/BA.
However, as mentioned in Section 3.2, the use of HMIPv6 reduces the
signaling overhead since no route optimization signaling is done for intra-
MAP handovers. In addition, naïve combinations of FMIPv6 and HMIPv6 often
result in redundant signaling. There is much work in the academic literature
and the IETF on more refined ways of combining signaling from the two
protocols to avoid redundant signaling.
Requirement #3 HMIPv6 may preserve location privacy, depending on the
dimension of the geographic area covered by the MAP. As discussed in Section
3.2, the mobile node still maintains a local care-of address that can be
exploited by worms or other malware.
Requirement #4 As mentioned for Requirement #2, the combination of HMIPv6
and FMIPv6 generates a lot of signaling overhead in the network. Concerning
payload data, in addition to the over-the-air MIPv6 tunnel, a further level
of tunneling is established between mobile node and MAP. Notice that this
tunnel is in place even for route optimized traffic. Moreover, if FMIPv6 is
directly applied to HMIPv6 networks, there is a third temporary handover-
related tunnel between the mobile node and previous access router. Again,
Kempf, et. al. Expires July 2006 [Page 13]
Internet Draft LMM Requirements and Gap Analysis Feburary, 2006
there is much work in the academic literature and IETF on ways to reduce the
extra tunnel overhead on handover by combining HMIP and FMIP tunneling.
Requirement #5 The signaling overhead in the network is not reduced by
HMIPv6, as mentioned in Section 3.2. Instead, FMIPv6 generates extra
signaling overhead between the previous access router and new access router
for HI/HAck exchange. For payload data, the same considerations as for
Requirement #4 are applicable.
Requirement #6 FMIPv6 requires the mobile node and the previous access
router to share a security association in order to secure the FBU/FBA
exchange. In addition, HMIPv6 requires that the mobile node and MAP share an
IPsec security association in order to secure LBU/LBA exchange. The only
well understood approach to set up an IPsec security association using of
certificates, but this may raise deployment issues. Thus, the combination of
FMIPv6 and HMIPv6 doubles the amount of mobile node to network security
protocol required, since security for both FMIP and HMIP must be deployed.
Requirement #7 HMIPv6 and FMIPv6 support multiple wireless technologies, so
this requirement is fufilled.
Requirement #8 The mobile node must support both HMIPv6 and FMIPv6
protocols, so this requirement is not fulfilled.
Requirement #9 Currently there is no IPv4 version of HMIPv6. There is an
IPv4 version of FMIP but it is not clear how it could be used together with
FMIPv6 in order to handle fast handovers across any wired network.
3.4 Micromobility Protocols
Researchers have defined some protocols that are often characterized as
micromobility protocols. Two typical protocols in this category are
Cellular-IP [22] and HAWAII [23]. Researchers defined these protocols before
local mobility optimizations for Mobile IP such as FMIP and HMIP were
developed, in order to reduce handover latency.
Cellular IP and HAWAII have a few things in common. Both are compatible
with Mobile IP and are intended to provide a higher level of handover
performance in local networks than was previously available with Mobile IP
without such extensions as HMIP and FMIP. Both use host routes installed in
a number of routers within a restricted routing domain. Both define specific
messaging to update those routes along the forwarding path and specify how
the messaging is to be used to update the routing tables and forwarding
tables along the path between the mobile and a micromobility domain boundary
router at which point Mobile IP is to used to handle scalable global
mobility. Unlike the FMIP and HMIP protocols, however, these protocols do
not require the mobile node to obtain a new care of address on each access
router as it moves; but rather, the mobile node maintains the same care of
address across the micromobility domain. From outside the micromobility
domain, the care of address is routed using traditional longest prefix
matching IP routing to the domain's boundary router, so the care of address
conceptually is within the micromobiity domain boundary router's subnet.
Kempf, et. al. Expires July 2006 [Page 14]
Internet Draft LMM Requirements and Gap Analysis Feburary, 2006
Within the micromobility domain, the care of address is routed to the
correct access router using host routes.
Cellular IP and HAWAII differ in a few aspects. Cellular IP seems to be
restricted, based on the nature of the protocol, to tree-based network
topologies. HAWAII claims to be applicable in both tree-based and more
complete network topologies. HAWAII documents more functionality in the
realm of reliability and QoS interworking. Both protocols involve the
mobile node itself in mobility operations, although this is also true of the
Mobile IP based optimizations, so both protocols raise the same security
concerns with respect to authorizing address update as the Mobile IP based
optimizations. HAWAII provides some analysis of network deployment
scenarios including scale, density, and efficiency, but some of these
assumptions seem very conservative compared to realistic cellular type
deployments.
Micromobility protocols have some potential drawbacks from a deployment and
scalability standpoint. Both protocols involve every routing element between
the mobile device and the micromobility domain boundary router in all packet
forwarding decisions specific to care of addresses for mobile nodes.
Scalability is limited because each care of address corresponding to a
mobile node generates a routing table entry, and perhaps multiple forwarding
table entries, in every router along the path. Since mobile nodes can have
multiple global care of addresses in IPv6, this can result in a large
expansion in router state throughout the micromobility routing domain.
Although the extent of the scalability for micromobility protocols is still
not clearly understood from a research standpoint, it seems certain that
they will be less scalable than the Mobile IP optimization enhancements, and
will require more specialized gear in the wired network.
The following is a gap analysis of the micromobility protocols against the
requirements in Section 2.0:
Requirement #1 The micromobility protocols reduce handover latency by
quickly fixing up routes between the boundary router and the access router.
While some additional latency may be expected during host route propagation,
it is typically much less than experienced with standard Mobile IP.
Requirement #2 The micromobility protocols require signaling from the mobile
node to the access router to initiate the host route propagation, but that
is a considerable reduction over the amount of signaling required to
configure to a new IP link.
Requirement #3 No care-of address changes are exposed to correspondent nodes
or the mobile node itself while the mobile node is moving in the
micromobility-managed network. Because there is no local care-of address,
there is no threat from malware that exposes the location by sending the
care-of address to an adversary.
Requirement #4 The only additional over-the-air signaling is involved in
propagating host routes from the mobile node to the network upon movement.
Kempf, et. al. Expires July 2006 [Page 15]
Internet Draft LMM Requirements and Gap Analysis Feburary, 2006
Since this signaling would be required for movement detection in any case,
it is expected to be minimal. Mobile node traffic experiences no overhead.
Requirement #5 Host route propagation is required throughout the wired
network. The volume of signaling could be more or less depending on the
speed of mobile node movement and the size of the wired network.
Requirement #6 The mobile node only requires a security association of some
type with the access router. Because the signaling is causing routes to the
mobile node's care-of address to change, the signaling must prove
authorization to hold the address.
Requirement #7 The micromobility protocols support multiple wireless
technologies, so this requirement is satisfied.
Requirement #8 The mobile node must support some way of signaling the access
router on link handover, but this is required for movement detection anyway.
The nature of the signaling for the micromobility protocols may mobile node
software changes, however.
Requirement #9 Most of the work on the micromobility protocols was done in
IPv4, but little difference could be expected for IPv6.
3.5 Standard Internal Gateway Route Distribution Protocols (OSPF and IS-IS)
It has also been suggested that instead of using a specialized
micromobility routing protocol in the access network, a standardized
Internal Gateway route distribution Protocol (IGP) such as IS-IS [25] or
OSPF [26] should be used to distribute host routes. Host route messages are
formatted in the IGPs by including a subnet mask in the route information
update, indicating that the address is a /32 for IPv4 or a /128 for IPv6
instead of a subnet prefix. Since IGPs typically distribute route
information by flooding, every router in the domain obtains a copy of the
host route eventually. Using an IGP instead of a micromobility protocol has
the advantage that standardized routing equipment can be used for all
routers in the access network, and, if a particular router goes down, the
host routes maintained along alternate routes should be sufficient to
continue routing, unlike micromobility protocols where only targeted routers
have the host routes.
Distributing host routes with an IGP has some significant disadvantages
however. One is that flooding requires a certain amount of time to converge;
so for some period after the link handover blackout, delivery to a mobile
node that has moved will be disrupted until convergence along the routes
traveled by the mobile node's traffic has occurred. Because micromobility
protocols target host routes back to the micromobility domain border router,
convergence can potentially be achieved more quickly. Tunnel-based solutions
such as HMIP don't suffer from convergence latency because only the two
endpoints need to know the routing. As a result, the internal routing
tables updated by the IGP remain stable when a mobile node moves. The
movement does not affect routing of traffic to other mobile nodes due to
intensive path computation.
Kempf, et. al. Expires July 2006 [Page 16]
Internet Draft LMM Requirements and Gap Analysis Feburary, 2006
Another disadvantage of using an IGP is that each router in the domain must
maintain a full host route table for all hosts. This requirement raises a
scalability issue. For example, an experiment [24] using OSPF to distribute
host routes through an access network consisting of a collection of rather
smallish enterprise routers indicated that about 25,000 routes could be
supported in 22 Mb of memory before performance started to degrade. This
works out to about 0.88 kb/host. Scaling this up to, say, 10 million hosts
(what one might expect in a large metropolitan area such as Tokyo or San
Francisco) would require about 8.8 Gb of memory per router. While memory
costs continue to drop, the amount of processing power for searching a
routing database of that size essentially means that each router in the
domain must have the same processing power as a high end, border router.
Micromobility and tunnel- based solutions don't suffer from this problem,
because the host route is local to the tunnel endpoints. Other routers in
the domain route based on highly scalable shortest matching network prefix
method.
The following is a gap analysis of host route distribution using a
standardized IGP against the requirements in Section 2.0:
Requirement #1 Host route distribution using an IGP is likely to suffer from
increased handover latency due to a lag time as routes converge over the
access network. The exact amount of latency depends on the convergence
characteristics of the particular IGP and the topology of the access
network, i.e. how fast convergence occurs along routes taken by the mobile
node's traffic.
Requirement #2 Host route distribution using an IGP requires signaling from
the mobile node to the access router to initiate the host route propagation,
but that is a considerable reduction over the amount of signaling required
to configure to a new IP link. However, if a mobile node is moving quickly,
the flooding traffic necessary to propagate a host route may not converge
before the mobile node hands over again. This could result in a cacscading
series of host route updates that never converge. Whether or not this effect
occurs depends on the size of the localized mobility domain, and so the need
to ensure convergence places an upper bound on the size of the domain or
expected movement speed of the mobile nodes.
Requirement #3 No care-of address changes are exposed to correspondent nodes
or the mobile node itself while the mobile node is moving in the localized
mobility management domain. Because there is no local care-of address, there
is no threat from malware that exposes the location by sending the care-of
address to an adversary.
Requirement #4 The only additional over-the-air signaling involved is
signaling from the mobile node to the access router indicating that the
mobile node has moved. Mobile node traffic experiences no overhead.
Requirement #5 Host route propagation is required throughout the wired
network. The volume of signaling could be more or less depending on the
speed of mobile node movement and the size of the wired network.
Kempf, et. al. Expires July 2006 [Page 17]
Internet Draft LMM Requirements and Gap Analysis Feburary, 2006
Requirement #6 The mobile node only requires a security association of some
type with the access router. Because the signaling is causing routes to the
mobile node's care-of address to change, the signaling must prove
authorization to hold the address.
Requirement #7 This requirement is satisfied by default, since the IGPs are
used over the wired backbone.
Requirement #8 The mobile node needs to perform some kind of active movement
detection with proof of identity to trigger the host route distribution, but
this kind of signaling is needed for movement regardless of whether
localized mobility management is deployed. Depending on the wireless link
type, this may be handled by the wireless link layer.
Requirement #9 Since the IGPs support both IPv4 and IPv6, both are
supported by this technique.
4.0 Security Considerations
There are two kinds of security issues involved in network-based localized
mobility management: security between the mobile node and the network, and
security between network elements that participate in the network-based
localized mobility management protocol
Security between the mobile node and the network itself consists of two
parts: threats involved in localized mobility management in general, and
threats to the network-based localized mobility management from the host.
The first is discussed above in Sections 2.3 and 2.6. The second is
discussed in the threat analysis document [27].
For threats to network-based localized mobility management, the basic threat
is an attempt by an unauthorized party to signal a bogus mobility event.
Such an event must be detectable. This requires proper bidirectional
authentication and authorization of network elements that participate in the
network-based localized mobility management protocol, and data origin
authentication on the signaling traffic between network elements.
5.0 Recommendation
In view of the gap analysis in Section 3.0, none of the existing solutions
provide complete coverage of the requirements. FMIPv6 provides a complete
solution to Requirement 3.1 but to no other requirement. FMIP, HMIP and
micromobility protocols require that the mobile node is modified to support the
additional functionality. But as analyzed above, the functionality provided
by each protocol is does not fully support the set of requirements discussed
in Section 2.0.
We therefore recommend that a new, network based localized mobility
management protocol be developed that minimizes or eliminates mobile node
Kempf, et. al. Expires July 2006 [Page 18]
Internet Draft LMM Requirements and Gap Analysis Feburary, 2006
involvement in localized mobility management. Such a localized mobility
management protocol can be treated as part of the network infrastructure.
This kind of architecture is required to address the gaps with existing
protocols described in Section 3.0. The new localized mobility management
protocol can be paired with a link layer specific IP link handover
optimization protocol, such as are provided by wireless LAN switches, or an
IP link handover optimization protocol, such as FMIPv6, to eliminate
handover related packet latency. The protocol should minimize the number of
specialized routers in the localized mobility management domain to reduce
the amount of state update needed upon movement and to allow standardized
network equipment to be used where mobility support is not required.
With the edge mobility approach, a mobile node has a single IP address that
does not change when the mobile node moves from one access router to
another, because the mobility anchor and access routers take care of
changing the routing. An edge mobility approach does not require a separate
security association with a network element, reducing the amount of overhead
required to get a connection up on the network. In an edge mobility approach,
mobile nodes only have link local addresses for access routers, so it is
much more difficult to mount off-link DoS attacks, and on-link attacks are
easier to trace and stop. With the edge mobility approach, no authentication
and authorization is necessary beyond that necessary for initial network
access and whatever additional authentication and authorization is required
by the wireless link layer upon movement between access points.
6.0 Author Information
James Kempf
DoCoMo USA Labs
181 Metro Drive, Suite 300
San Jose, CA 95110
USA
Phone: +1 408 451 4711
Email: kempf@docomolabs-usa.com
Kent Leung
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134
USA
EMail: kleung@cisco.com
Phil Roberts
Motorola Labs
Schaumberg, IL
USA
Email: phil.roberts@motorola.com
Katsutoshi Nishida
NTT DoCoMo Inc.
3-5 Hikarino-oka, Yokosuka-shi
Kempf, et. al. Expires July 2006 [Page 19]
Internet Draft LMM Requirements and Gap Analysis Feburary, 2006
Kanagawa,
Japan
Phone: +81 46 840 3545
Email: nishidak@nttdocomo.co.jp
Gerardo Giaretta
Telecom Italia Lab
via G. Reiss Romoli, 274
10148 Torino
Italy
Phone: +39 011 2286904
Email: gerardo.giaretta@tilab.com
Marco Liebsch
NEC Network Laboratories
Kurfuersten-Anlage 36
69115 Heidelberg
Germany
Phone: +49 6221-90511-46
Email: marco.liebsch@ccrle.nec.de
7.0 Informative References
[1] Kempf, J., Leung, K., Roberts, P., Nishda, K., Giaretta, G., Liebsch,
M., and Gwon, Y., "Problem Statement for IP Local Mobility," Internet
Draft, work in progress.
[2] Manner, J., and Kojo, M., "Mobility Related Terminology", RFC 3753,
June, 2004.
[3] Devarapalli,V., Wakikawa, R., Petrescu, A., Thubert, P., "Network
Mobility (NEMO) Basic Support Protocol", RFC 3963, January, 2005.
[4] Carpenter, B., "Architectural Principles of the Internet," RFC 1958,
June, 1996.
[5] Johnson, D., Perkins, C., and Arkko, J., "Mobility Support in IPv6",
RFC 3775.
[6] Moskowitz, R., Nikander, P., Jokela, P., and Henderson, T., "Host
Identity Protocol", Internet Draft, work in progress.
[7] Choi, J, and Daley, G., " Goals of Detecting Network Attachment in
IPv6", Internet Draft, work in progress.
[8] IEEE, "Port-based Access Control", IEEE LAN/MAN Standard 802.1x, June,
2001.
[9] Forsberg, D., Ohba, Y., Patil, B., Tschofenig, H., and Yegin, A.,
"Protocol for Carrying Authentication for Network Access (PANA)",
Internet Draft, work in progress.
[10] Arkko, J., Kempf, J., Zill, B., and Nikander, P., "SEcure Neighbor
Discovery (SEND)", RFC 3971, March, 2005.
[11] Moore, N., "Optimistic Neighbor Discovery", Internet Draft, Work in
Progress.
[12] Ackerman, L., Kempf, J., and Miki, T., "Wireless Location Privacy: Law
and Policy in the US, EU, and Japan", ISOC Member Briefing #15,
http://www.isoc.org/briefings/015/index.shtml
Kempf, et. al. Expires July 2006 [Page 20]
Internet Draft LMM Requirements and Gap Analysis Feburary, 2006
[13] Haddad, W., Nordmark, E., Dupont, F., Bagnulo, M., Park, S.D., and
Patil, B., "Privacy for Mobile and Multi-homed Nodes: MoMiPriv Problem
Statement", Internet Draft, work in progress.
[14] Kivinen, T., and Tschopfening, H., "Design of the MOBIKE Protocol",
Internet Draft, work in progress.
[15] Koodli, R., "IP Address Location Privacy and IP Mobility", Internet
Draft, work in progress.
[16] Koodli, R., Devarapalli, V., Flinck, H., and Perkins, C., "Solutions
for IP Address Location Privacy in the presence of IP Mobility",
Internet Draft, work in progress.
[17] Bao, F., Deng, R., Kempf, J., Qui, Y., and Zhou, J., "Protocol for
Protecting Movement of Mobile Nodes in Mobile IPv6", Internet Draft,
work in progress.
[18] Soliman, H., Tsirtsis, G., Devarapalli, V., Kempf, J., Levkowetz, H.,
Thubert, P, and Wakikawa, R. "Dual Stack Mobile IPv6 (DSMIPv6) for
Hosts and Routers", Internet Draft, work in progress.
[19] Koodli, R., editor, "Fast Handovers for Mobile IPv6", RFC 4068, July,
2005.
[20] Soliman, H., Castelluccia, C., El Malki, K., and Bellier, L.,
"Hierarchical Mobile IPv6 Mobility Management (HMIPv6)", RFC 4140,
August, 2005.
[21] Kempf, J., and Koodli, R., "Bootstrapping a Symmetric IPv6 Handover Key
from SEND", Internet Draft, work in progress.
[22] Campbell, A., Gomez, J., Kim, S., Valko, A., and Wan, C., "Design,
Implementation and Evaluation of Cellular IP", IEEE Personal
Communications, June/July 2000.
[23] Ramjee, R., La Porta, T., Thuel, S., and Varadhan, K., "HAWAII: A
domain-based approach for supporting mobility in wide-area wireless
networks", in Proceedings of the International Conference on Networking
Protocols (ICNP), 1999.
[24] "Mobile VPN Network Configuration Alternatives", IP Unplugged,
http://www.ipunplugged.com/pdf/Network-blueprints_A.pdf.
[25] Oran, D., "OSI IS-IS Intra-domain Routing Protocol", RFC 1142,
Feburary, 1990.
[26] Moy, J., "OSPF Version 2", STD 54, April, 1998.
[27] Threat analysis draft, TBD
8.0 IPR Statements
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in this
document or the extent to which any license under such rights might or might
not be available; nor does it represent that it has made any independent
effort to identify any such rights. Information on the procedures with
respect to rights in RFC documents can be found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any assurances of
licenses to be made available, or the result of an attempt made to obtain a
general license or permission for the use of such proprietary rights by
Kempf, et. al. Expires July 2006 [Page 21]
Internet Draft LMM Requirements and Gap Analysis Feburary, 2006
implementers or users of this specification can be obtained from the IETF
on-line IPR repository at http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary rights that
may cover technology that may be required to implement this standard.
Please address the information to the IETF at ietf-ipr@ietf.org.
9.0Disclaimer of Validity
This document and the information contained herein are provided on an "AS
IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS OR IS
SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT
LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT
INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE.
10.0 Copyright Notice
Copyright (C) The Internet Society (2006). This document is subject to the
rights, licenses and restrictions contained in BCP 78, and except as set
forth therein, the authors retain all their rights.
11.0 Changes in 01 (remove before publication)
- Changed wording so as not to seem to exclude mobile routers;
. Changed "host" to "mobile node" when the wireless device is meant,
. Changed "host" or "host-based" when localized mobility management is
described to be "mobile node",
. Removed definition for "host" and added a definition to Section 1.1
for "mobile node" to indicate that the end device is meant to apply to
mobile routers that use a global mobility management protocol such as
NEMO in addition to terminals,
- Modified Section 2.7 to indicate that support for multiple wireless link
technologies is not meant to include keeping the same IP address when a new
wireless interface is activated on the mobile device,
- Modified Section 2.8 to indicate that unmodified mobile node support is
meant to apply only to localized mobility management, and is not meant to
exclude global mobility management or driver changes needed to support
handover at the wireless link layer,
- Changed the text in Section 4.0 to clarify the difference in the threat
from host-side malware for global mobility protocols such as Mobile IPv6 and
localized mobility management,
Kempf, et. al. Expires July 2006 [Page 22]
Internet Draft LMM Requirements and Gap Analysis Feburary, 2006
- Rewrote Section 4 to remove text that duplicates discussions in Section
2.3 and 2.6, and focused instead on the threat to the NETLMM protocol
itself.
- Added Section 3.5 discussing use of standardized IGPs for host route
distribution.
- Added text to each subsection in Section 2 that clearly and explicitly
states the requirement for the NETLMM protocol. Previously, the
requirements were in some cases only implicit in the discussion.
- Added reference to Threat Analysis draft (TBD).
Kempf, et. al. Expires July 2006 [Page 23]
