INTERNET DRAFT EXPIRES SEPT 1998 INTERNET DRAFT
N.S.C Working Group A.Robert
INTERNET DRAFT SITA
Category: Informational March 1998
MAPPING OF AIRLINE TRAFFIC OVER IP
<draft-rfced-info-matip-00.txt>
Status of This Memo
This document is an Internet-Draft. Internet-Drafts are working
documents of the Internet Engineering Task Force (IETF), its
areas, and its working groups. Note that other groups may also
distribute working documents as Internet-Drafts.
Internet-Drafts are draft documents valid for a maximum of six
months and may be updated, replaced, or obsoleted by other
documents at any time. It is inappropriate to use Internet-
Drafts as reference material or to cite them other than as
"work in progress."
To learn the current status of any Internet-Draft, please check
the "1id-abstracts.txt" listing contained in the Internet-
Drafts Shadow Directories on ftp.is.co.za (Africa),
ftp.nordu.net (Europe), munnari.oz.au (Pacific Rim),
ds.internic.net (US East Coast), or ftp.isi.edu (US West Coast).
Distribution of this document is unlimited.
Abstract
This memo specifies a protocol for the encapsulation of the airline
specific protocol over IP.
Contents
. INTRODUCTION 3
2. TERMINOLOGY & ACRONYMS 5
3. LAYERING 7
4. TRAFFIC IDENTIFICATION 8
5. TCP PORT ALLOCATION 8
6. MATIP SESSION ESTABLISHMENT 8
SITA [Page 1]
7. OVERALL PACKET FORMAT FOR TYPE A & TYPE B 10
8. MATIP FORMAT FOR TYPE A CONVERSATIONAL TRAFFIC 11
8. 1 Control Packet Format 11
8.1.1 Session Open format (SO) 11
8.1.2 Open Confirm format (OC) 13
8.1.3 Session Close (SC) 14
8.2 Data Packet Format 15
9. MATIP FORMAT FOR TYPE A HOST-TO-HOST TRAFFIC 16
9. 1 Control Packet Format 16
9.1.1 Session Open format (SO) 16
9.1.2 Open Confirm format (OC) 18
9.1.3 Session Close (SC) 19
9.2 Data Packet Format 19
10. MATIP FORMAT FOR TYPE B TRAFFIC 20
10.1 Control packet format 20
10.1.1 Session Open format (SO) 20
10.1.2 Open confirm format (OC) 21
10.1.3 Session Close (SC) 22
10.2 Data packet format 23
11. SECURITY 23
12. AUTHOR ADDRESS 24
SITA [Page 2]
. Introduction
The airline community has been using a worldwide data network for over
40 years, with two main types of traffic:
Transactional traffic
This is used typically for communication between an airline office or
travel agency and a central computer system for seat reservations and
ticket issuing. A dumb terminal or a PC accesses the central system
(IBM or UNISYS) through a data network.
This traffic is also called TYPE A and is based on real-time
query/response with limited protection, high priority and can be
discarded. The user can access only one predetermined central computer
system. In case of no response (data loss), the user can duplicate the
request.
Messaging
This is an e-mail application where real-time is not needed. However a
high level of protection is required. The addressing scheme uses an
international format defined by IATA and contains the city and airline
codes.
This traffic is also called TYPE B and is transmitted with a high
level of protection, multi-addressing and 4 levels of priority.
The detailed formats for TYPE A and TYPE B messages are defined in the
IATA standards.
At the bottom level, synchronous protocols have been built since
1960's and well before the OSI and SNA standards.
At present, there is a big number of legacy equipment installed in
thousands of airline offices around the world. Many airlines do not
have immediate plans to replace their terminals with more modern
equipment using open standards. They are in search of more economical
ways for connecting these terminals to the present reservation system.
Most airlines are willing to migrate from airline specific protocols
to standardized protocols in order to benefit from the lower cost of
new technologies, but the migration has been slow done to the
following factors:
SITA [Page 3]
- Applications have not been migrated.
- Dumb terminals using airline protocols P1024B (IBM ALC) or P1024C
(UNISYS UTS) are still numerous.
There are currently many different proprietary solutions based on
gateways available to take advantage of low cast networking, but they
are not scalable and cannot interact.
In the future, TCP/IP will be more commonly used as a common transport
means for traffic types because:
- TCP/IP is the standard protocol of UNIX based applications
- TCP/IP stacks are inexpensive
- TCP/IP is used on intranets.
The purpose of this memo is to define the mapping of the airline
traffic types over TCP/IP. The airlines implementing it in their
systems should have a TCP/IP stack to enable the traffic exchange
below :
!----! ( )
! !----------( )
!----! ( )
Type B HOST ( NETWORK )
( )
( ) !---o
!----! ( )--------! D !---o Type A stations
!----!----------( ) !---o
!----! ( )
TYPE A HOST !
!
!
!
--------
! !
--------
Network Messaging System
(D) : Gateway TYPE A router
The different airline traffic flows concerned by this memo are :
- TYPE A Host / Terminal
- TYPE A Host / TYPE A host
- TYPE B Host / Network messaging System
SITA [Page 4]
In the case of dumb terminals, a conversion is required on the
terminal side in order to have an IP connection between the host and
the router. However, the IP connection is directly between the central
airline host and the intelligent workstation if the latter has a
direct connection to the network, a TCP/IP stack and a terminal
emulation
2. Terminology & acronyms
ALC :
Airline Line Control: IBM airline specific protocol (see P1024B)
ASCII
American Standard Code for Information Interchange
ASCU
Agent Set Control Unit: Cluster at the user side.
AX.25
Airline X.25 : Airline application of the X.25 OSI model (published by
IATA)
BAUDOT
Alphabet defined in ITU-T Number 5. BAUDOT uses 5 bits. Padded BAUDOT
uses 7 bits with the Most significant bit (bit 7) for the parity and
the bit 6 equal to 1.
BATAP
Type B Application to Application Protocol. Protocol to secure the
TYPE B traffic. It was specified by SITA and is now published by IATA
(SCR Vol. 3)
EBCDIC
Extended Binary Coded Decimal Interchange Code
Flow ID Traffic
Flow identifier used in host to host traffic to differentiate traffic
flow types.
HLD
High Level Designator: Indicates the entry or exit point of a block in
the network.
IA
SITA [Page 5]
Interchange Address: ASCU identifier in P1024B protocol.
IATA
International Air Transport Association
IP
Internet Protocol
IPARS
International Program Airline Reservation System: IPARS code is used
in ALC
HTH
Host to Host (traffic).
LSB
Least Significant Bit
MATIP
Mapping of Airline Traffic over Internet Protocol
MSB
Most Significant Bit
OC
Open Confirm (MATIP command)
OSI
Open Standard Interface
P1024B
SITA implementation of the ALC, the IBM airlines specific protocol. It
uses 6- bit padded characters (IPARS) and IA/ TA for physical
addressing.
P1024C
SITA implementation of the UTS, the UNISYS terminal protocol. It uses
7-bit (ASCII) characters and RID/ SID for physical addressing.
RFU
Reserved for Future Use
RID
Remote Identifier: ASCU identifier in P1024C protocol.
SC
Session Close (MATIP command)
SITA [Page 6]
SCR : System and Communication Reference. (IATA document)
SID
Station Identifier: Terminal identifier in P1024C protocol.
SITA
Societe International de Telecommunications Aeronautiques
SO
Session Open (MATIP command)
TA
Terminal Address: Terminal identifier in P1024B protocol.
TCP
Transport Control Protocol
TYPE A Traffic
Interactive traffic or host to host
TYPE B Traffic
Messaging traffic in IATA compliant format with high level of
reliability
UTS
Universal Terminal System by Unisys: (see P1024C)
3. LAYERING
MATIP is an end to end protocol. Its purpose is to have a mapping
standard between the TCP layer and the airline application without any
routing element.
+-------------------------------+
|Airline TYPE A | Airline TYPE B|
| | Application |
| |---------------|
| Application | BATAP |
+-------------------------------+
| MATIP A | MATIP B |
+-------------------------------+
| T.C.P |
+-------------------------------+
| I.P |
+-------------------------------+
SITA [Page 7]
| MEDIA |
+-------------------------------+
4. TRAFFIC IDENTIFICATION
In TYPE A conversational traffic, the airline host application
recognizes the ASCU due to 4 bytes (H1, H2, A1, A2). These bytes are
assigned by the host and are unique per ASCU. Thus, a host can
dynamically recognize the ASCU independent of IP address.
H1 H2 A1 A2 bytes follow one of the three cases below:
- A1,A2 only are used and H1H2 is set to 0000.
- H1,H2 identify the session and A1A2 the ASCU inside the session.
- H1,H2,A1,A2 identify the ASCU.
The first two cases are fully compatible with the AX.25 mapping where
H1H2 may be equivalent to the HLD of the concentrator, i.e., 2 bytes
hexadecimal. The third rule allows more flexibility but is not
compatible with AX.25.
In TYPE A host to host traffic the identification field is also
present and is equal to 3 bytes H1 H2 Flow ID (optional). H1H2 are
reserved for remote host identification (independently of the IP
address) and must be allocated bilaterally.
In Type B traffic, identification of End Systems may be carried out by
the use of HLDs, or directly by the pair of IP addresses.
5. TCP PORT ALLOCATION
IANA (Internet Assigned Numbers Authority) has allocated the following
ports for MATIP TYPE A and TYPE B traffic:
MATIP Type A TCP port = 350
MATIP Type B TCP port = 351
Therefore the traffic type A or B is selected according to the TCP port.
6. MATIP SESSION ESTABLISHMENT
Prior to any exchange between two applications, a single MATIP session
is established above the TCP connection in order to identify the
traffic characteristic such as:
SITA [Page 8]
- Subtype of traffic for TYPE A (Type A host to host or Type A
conversational )
- Multiplexing used (for Type A)
- Data header
- Character set
A separate session and TCP connection must be established for each set
of parameters (e.g., P1024B, P1024C traffic between two points needs
two separate sessions).
The establishment of a MATIP session can be initiated by either side.
No keep-alive mechanism is defined at MATIP level. Session time out
relies on the TCP time-out parameters.
There are three commands defined to manage the MATIP session:
- Session Open (SO) to open a session.
- Open Confirm (OC) to confirm the SO command.
- Session close (SC) to close the current session.
A MATIP session can be up only if the associated TCP connection is up.
However it is not mandatory to close the TCP connection when closing
the associated MATIP session.
Typical exchange is:
TCP session establishment
Session Open --------->
<----------- Open confirm
data exchange
---------------------->
<-------------------------
.
.
.
Session Close ----------------->
.
.
.
<------------------------- Session Open
Open confirm ------------------->
data exchange
<-------------------------
---------------------->
The Session Open command may contain configuration elements. An Session
Open command received on a session already opened (i.e. same IP address
SITA [Page 9]
and port number) will automatically clear the associated configuration
and a new configuration will be set up according to the information
contained in the new open session command.
As illustrated above, the open and close commands are symmetrical.
For type A conversational traffic, the SO and OC commands contain
information for the identification of the ASCUs and the session. ASCUs
are identified within a session by two or 4 bytes. A flag is set to
indicate if the ASCU is identified by 4 bytes (H1H2A1A2) or by 2 bytes
(A1A2). In the latter case, H1H2 is reserved for session identification.
The SO command is sent to open the MATIP session. In Type A
conversational it may contains the list of ASCUs configured in this
session.
The OC command confirms the SO command. It can refuse or accept it,
totally or conditionally. In Type A, it contains the list of the ASCUs
either rejected or configured in the session.
7. OVERALL PACKET FORMAT FOR TYPE A & TYPE B
The first 4 bytes of the MATIP header follow the following rules.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0|0|0|0|0| Ver |C| Cmd | length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Ver
The `Ver' (Version) field represents the version of the MATIP. It must
contain the value 001 otherwise the packet is considered as invalid.
C
Identifies a CONTROL packet.
When set to 1, the packet is a Control packet
When set to 0, the packet is a Data packet
Cmd
This field identifies the control command if the flag C is set to 1.
Length
This field indicates the number of bytes of the whole packet, header
included.
SITA [Page 10]
Notes : Fields identified as optional (Opt) are not transmitted if not
used.
8. MATIP FORMAT FOR TYPE A CONVERSATIONAL TRAFFIC
8. 1 Control Packet Format
There are 3 control packets to open or close the session at the MATIP
level.
8.1.1 Session Open format (SO)
To be able to identify the session and before sending any data
packets, a Session Open command is sent. It can be initiated by either
side. In case of collision, the open session from the side having the
lower IP address is ignored.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0|0|0|0|0| Ver |1|1 1 1 1 1 1 0| length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0 0|0 1|0| CD | STYP |0 0 0 0| RFU |MPX|HDR| PRES. |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| H1 | H2 | RFU |
|-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Reserved | RFU | Nbr of ASCUs |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Nbr of ASCUs | ASCU list (opt) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
RFU
Reserved for future use. Must be set to zero.
CD
This field specifies the Coding
000 : 5 bits (padded baudot)
010 : 6 bits (IPARS)
100 : 7 bits (ASCII)
110 : 8 bits (EBCDIC)
xx1 : R.F.U
STYP
SITA [Page 11]
This is the traffic subtype (type being TYPE A).
0001 : TYPE A Conversational
MPX
This flag specifies the multiplexing used within the TCP session.
Possible values are:
00 : Group of ASCU with 4 bytes identification per ASCU (H1H2A1A2)
01 : Group of ASCUs with 2 bytes identification per ASCU (A1A2)
10 : single ASCU inside the TCP session.
HDR
This field specifies which part of the airline's specific address is
placed ahead of the message texts transmitted over the session.
Possible values are :
00 : ASCU header = H1+H2+A1+A2
01 : ASCU Header = A1+A2
10 : No Header
11 : Not used
The MPX and HDR must be coherent. When ASCUs are multiplexed, the data
must contain the ASCU identification. The table below summarizes the
allowed combinations :
+--------------------------+
| MPX | 00 | 01 | 10 |
+--------------------------+
| HDR | |
| 00 | Y | Y | Y |
| 01 | N | Y | Y |
| 10 | N | N | Y |
+--------------------------+
PRES
This field indicates the presentation format
0001 : P1024B presentation
0010 : P1024C presentation
0011 : 3270 presentation
H1 H2
These fields can logically identify the session if MPX is not equal to
00. When this field is not used, it must be set to 0. If used in
session (MPX <> 0) with HDR=00, H1H2 in data packet must have the same
value as set in SO command.
SITA [Page 12]
Nbr of ASCUs
Nbr_of_ASCUs field is mandatory and gives the number of ASCUs per
session. A 0 (zero) value means unknown. In this case the ASCU list is
not present in the `Open Session' command and must be sent by the
other end in the `Open Confirm' command.
ASCU LIST
Contains the list of identifier for each ASCU. If MPX=00 it has a
length of four bytes (H1H2A1A2) for each ASCU, otherwise it is two
bytes (A1A2).
8.1.2 Open Confirm format (OC)
The OC (Open Confirm) command is a response to an SO (Session Open)
command and is used to either refuse the session or accept it
conditionally upon checking hte configuration of each ASCU.
In case of acceptance, the OC indicates the number and the address of
the rejected ASCUs, if any. Alternatively, it indicates the list of
ASCUs configured for that MATIP session if the list provided by the SO
command was correct or the number of ASCUs configured in the session
was unknown (n. of ASCU equals 0).
8.1.2.1 Refuse the connection
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0|0|0|0|0| Ver |1|1 1 1 1 1 0 1|0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| cause |
+-+-+-+-+-+-+-+-+
Cause
This field indicates the reason for the MATIP session refusal :
0 0 0 0 0 0 0 1 : No Traffic Type matching between Sender &
Recipient
0 0 0 0 0 0 1 0 : Information in SO header incoherent
1 0 0 0 0 1 0 0
up to : Application dependent
1 1 1 1 1 1 1 1
Other values reserved.
SITA [Page 13]
As specified in chapter 6, an already opened session is closed in this
case.
8.1.2.2 Accept the connection
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0|0|0|0|0| Ver |1|1 1 1 1 1 0 1| length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0 0 R 0 0 0 0 0| Nbr of ASCUs |Nbr of ASCU(opt| ASCU LIST |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
R
Flag indicating an error in the ASCU configuration provided in the SO
command.
NBR of ASCUs
If the MPX value is equal to 00 in the SO command, this field is two
bytes long. Otherwise, it is one byte.
If the R flag is set, the Nbr_of_ASCUs field represents the number of
ASCUs in error. Otherwise, it indicates the number of ASCUs configured
for that MATIP session.
Notes : The length of this field is either one or two bytes. In the SO
command, the length is always two bytes. This discrepancy comes from
backward compatibility with AX25 (see chapter 4). In the SO command,
it is possible to use a free byte defined in the AX25 call user data.
Unfortunately, there is no such free byte in the AX25 clear user data.
ASCU LIST
Depending on the R flag, this field indicates the list of ASCUs (A1A2
or H1H2A1A2) either in error or within the session.
8.1.3 Session Close (SC)
The SC (Session Close) command is used to close an existing MATIP
session.
SITA [Page 14]
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0|0|0|0|0| Ver |1|1 1 1 1 1 0 0|0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Close Cause |
+-+-+-+-+-+-+-+-+
Close Cause
Indicates the reason for the session closure:
0 0 0 0 0 0 0 0 : Normal Close
1 0 0 0 0 1 0 0
up to : Application dependent
1 1 1 1 1 1 1 1
Other values reserved.
8.2 Data Packet Format
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0|0|0|0|0| Ver |0|0 0 0 0 0 0 0| length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ID (optional) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
| Payload |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
ID
This field is optional and has a different length and format according
to the value of HDR, PRES indicated during the session establishment.
+------------------------------+-------------------------------+
|HDR | PRES = P1024B and 3270 | PRES = P1024C |
+------------------------------+-------------------------------+
|00 |ID = 4 bytes H1-H2-A1-A2 | ID = 5 bytes H1-H2-A1-0x01-A2 |
SITA [Page 15]
+------------------------------+-------------------------------+
|01 |ID = 2 bytes A1-A2 | ID = 3 bytes A1-0x01-A2 |
+------------------------------+-------------------------------+
|10 |ID = 0 bytes | ID = 0 bytes |
+------------------------------+-------------------------------+
H1, H2 value must match the value given in the SO command if MPX is
different from 0.
Payload
payload begins with the terminal identification :
- One byte Terminal identifier (TA) in P1024B
- Two bytes SID/DID Terminal identifier in P1024C.
9. MATIP FORMAT FOR TYPE A HOST-TO-HOST TRAFFIC
9. 1 Control Packet Format
There are 3 control packets to open or close the session at the MATIP
level.
9.1.1 Session Open format (SO)
To be able to identify the session and before sending any data packet,
a Session Open command is sent. It can be initiated by either side. In
case of collision, the open session from the side having the lower IP
address is ignored.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0|0|0|0|0| Ver |1|1 1 1 1 1 1 0| length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0 0|0 1|0| CD | STYP |0 0 0 0| RFU |MPX|HDR|0 0 0 0|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| H1 | H2 | RFU |
|-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Flow ID(opt)|
+-+-+-+-+-+-+-+-+
RFU
SITA [Page 16]
Reserved for future use. Must be set to zero.
CD
This field specifies the Coding, as defined in section 8.1.1.1.
STYP
This is the traffic subtype (type being Type A).
0010 : TYPE A IATA Host to Host
1000 : SITA Host to Host
MPX
This flag specifies the multiplexing used within the MATIP session in
TYPE A SITA host to host. Possible values are:
00 : irrelevant
01 : multiple flow inside the TCP connection
10 : single flow inside the TCP connection
HDR
This field specifies which part of the airline's specific address is
placed ahead of the message text transmitted over the session.
Possible values are :
00 : used in TYPE A SITA Host to Host Header = H1+H2+Flow ID
01 : used in TYPE A SITA Host to Host Header = Flow ID
10 : No Header (default for IATA host to Host)
11 : Not used
The MPX and HDR must be coherent. When flow are multiplexed, the data
must contain the flow identification. The table below summarizes the
possible combinations:
+---------------------+
| MPX | 01 | 10 |
+---------------------+
| HDR | | |
| 00 | Y | Y |
| 01 | Y | Y |
| 10 | N | Y |
+---------------------+
SITA [Page 17]
H1 H2
These fields can be used to identify the session. When this field is
not used, it must be set to 0. If HDR=00, H1H2 in data packet must
have the same value as set in SO command.
Flow ID
This field is optional and indicates the Flow ID (range 3F - 4F Hex).
9.1.2 Open Confirm format (OC)
The OC (Open Confirm) command is a response to an SO (Session Open)
command and is used to either refuse the session or accept it.
9.1.2.1 Refuse the connection
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0|0|0|0|0| Ver |1|1 1 1 1 1 0 1|0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| cause |
+-+-+-+-+-+-+-+-+
Cause
This field indicates the reason for the MATIP session refusal
0 0 0 0 0 0 0 1 : No Traffic Type matching between Sender &
Recipient
0 0 0 0 0 0 1 0 : Information in SO header incoherent
1 0 0 0 0 1 0 0
up to : Application dependent
1 1 1 1 1 1 1 1
Other values reserved.
9.1.2.2 Accept the connection
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0|0|0|0|0| Ver |1|1 1 1 1 1 0 1|0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0 0 0 0 0 0 0 0|
SITA [Page 18]
+-+-+-+-+-+-+-+-+
9.1.3 Session Close (SC)
The SC (Session Close) command is used to close an existing MATIP
session.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0|0|0|0|0| Ver |1|1 1 1 1 1 0 0|0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Close Cause |
+-+-+-+-+-+-+-+-+
Close Cause
Indicates the reason for the session closure:
0 0 0 0 0 0 0 0 : Normal Close
1 0 0 0 0 1 0 0
up to : Application dependent
1 1 1 1 1 1 1 1
Other values reserved
9.2 Data Packet Format
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0|0|0|0|0| Ver |0|0 0 0 0 0 0 0| length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ID (optional) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
| Payload |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
ID
SITA [Page 19]
This field is optional and has a different length and format according
to the value of HDR indicated during the session establishment.
+-------------------------------+
|HDR | I.D. |
+-------------------------------+
|00 |ID = 3 bytes H1-H2 FLOW ID|
+-------------------------------+
|01 |ID = FLOW ID |
+-------------------------------+
|10 |ID nor present |
+-------------------------------+
Payload packet
The payload format is relevant to the MATIP layer. It is formatted
according to the IATA host to host specifications and agreed
bilaterally by the sender and the receiver.
10. MATIP FORMAT FOR TYPE B TRAFFIC
10.1 Control packet format
There are 3 control packets used to open or close the session at the
MATIP level for exchanging Type B data
10.1.1 Session Open format (SO)
Before sending any data packets, it is recommended to let the systems
establishing a session check that they are indeed able to communicate
(i.e.: Both systems agree on the characteristics of the traffic that
will cross the connection). For this purpose, a two way handshake,
using the Session commands defined hereafter, is performed immediately
after the establishment of the TCP level connection. Either side can
initiate this procedure. In case of collision, the open session from
the side having the lower IP address is ignored.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0|0|0|0|0| Ver |1|1 1 1 1 1 1 0| length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0 0 0 0 0| C D | PROTEC| BFLAG | Sender HLD |
SITA [Page 20]
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Recipient HLD |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Length
This field indicates the number of bytes of the whole command, header
included. The only possible values are equal to 6 bytes or 10 bytes.
CD
This field specifies the Coding, as defined in section 8.1.1.1.
PROTEC
Identifies the end to end Messaging Responsibility Transfer protocol
used.
0010: BATAP
All other values available.
BFLAG (X means `do not care'
X X 0 0 means that the fields `Sender HLD, Recipient HLD' do not exist
in this packet. In this case, the exact length of the packet is 6
Bytes.
X X 1 0 means that the `Sender HLD, Recipient HLD' are carried
respectively in bytes 9,10 and 11,12 of this packet. In this
case, the exact length of the packet is 10 Bytes.
0 0 X X means that the connection request has been transmitted from a
host (Mainframe system)
0 1 X X means that the connection request has been transmitted from a
gateway)
Sender HLD
HLD of the Type B System sending the Session Open.
Recipient HLD
HLD of the Type B system to which session opening is destined.
10.1.2 Open confirm format (OC)
The OC (Open Confirm) command is a response to an SO (Session Open)
SITA [Page 21]
command and is used to either refuse the session or accept it.
10.1.2.1 Refuse the connection
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0|0|0|0|0| Ver |1|1 1 1 1 1 0 1|0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0|1| Cause |
+-+-+-+-+-+-+-+-+
Length of this packet is 5 Bytes.
Cause
Indicates the cause of the rejection
0 0 0 0 0 1 : No Traffic Type matching between Sender & Recipient
0 0 0 0 1 0 : Information in SO header incoherent
0 0 0 0 1 1 : Type of Protection mechanism are different
0 0 0 1 0 0 up to 1 1 1 1 1 1 : R.F.U
10.1.2.2 Accept the connection
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0|0|0|0|0| Ver |1|1 1 1 1 1 0 1|0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0 0 0 0 0 0 0 0|
+-+-+-+-+-+-+-+-+
Length of this packet is 5 Bytes.
10.1.3 Session Close (SC)
The SC (Session Close) command is used to close an existing MATIP
session.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0|0|0|0|0| Ver |1|1 1 1 1 1 0 0|0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Close Cause |
SITA [Page 22]
+-+-+-+-+-+-+-+-+
Close Cause
Indicates the reason for the session closure:
0 0 0 0 0 0 0 0 : Normal Close
1 0 0 0 0 1 0 0 up to 1 1 1 1 1 1 1 1 : Application dependent
Other values reserved
10.2 Data packet format
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0|0|0|0|0| Ver |0|0 0 0 0 0 0 0| length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
| Payload |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Length
This field indicates the number of bytes of the whole packet, header
included.
Payload
Type B message formatted according to the IATA standard and conforming
to the rules of the accessed TYPE B service
11. Security
The security is a very sensitive point for airline industry. Security
for the MATIP users can take place at different levels :
The ASCU must be defined to enable the session with the host
application. The control can be achieved in two ways: either the ASCU
address (H1 H2 A1 A2) is defined at the application level by the means
of a static configuration, or the ASCU is identified by a User ID /
password. In most cases, the User ID and Password are verified by a
dedicated software running in the central host. But they can also be
checked by the application itself.
SITA [Page 23]
The MATIP sessions being transported over TCP/IP, It can go through a
firewall. Depending on the firewall level, the control can be
performed at network (IP addresses) or TCP application layer.
For higher level of security all compliant implementations MAY
implement IPSEC ESP for securing control packets. Replay
protection, the compulsory cipher suite for IPSEC ESP, and NULL
encryption MAY be implemented. Optionally, IPSEC AH MAY also be
supported. All compliant implementations MAY also implement IPSEC ESP
for protection of data packets. Replay prevention and integrity
protection using IPSEC ESP mandated cipher suit MAY be implemented.
NULL encryption also MAY be supported. Other IPSEC ESP required
ciphers MAY also be supported.
12. Author address
Alain Robert
S.I.T.A.
18, rue Paul Lafargue
92904 PARIS LA DEFENSE 10
FRANCE
Phone : 33 1 46411491
Fax : 33 1 46411277
Email : arobert par1.par.sita.int
@
SITA [Page 24]
INTERNET DRAFT EXPIRES SEPT 1998 INTERNET DRAFT