Internet Engineering Task Force H. Chen
Internet-Draft R. Li
Intended status: Standards Track Huawei Technologies
Expires: July 20, 2014 G. Cauchie
A. Retana
Cisco Systems, Inc.
N. So
Tata Communications
M. Toy
Comcast
L. Liu
UC Davis
January 16, 2014
OSPF Topology-Transparent Zone
draft-chen-ospf-ttz-07.txt
Abstract
This document presents a topology-transparent zone in a domain. A
topology-transparent zone comprises a group of routers and a number
of links connecting these routers. Any router outside of the zone is
not aware of the zone. The information about the links and routers
inside the zone is not distributed to any router outside of the zone.
Any link state change such as a link down inside the zone is not seen
by any router outside of the zone.
Status of this Memo
This Internet-Draft is submitted to IETF in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on July 20, 2014.
Copyright Notice
Chen, et al. Expires July 20, 2014 [Page 1]
Internet-Draft Topology-Transparent Zone January 2014
Copyright (c) 2014 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Conventions Used in This Document . . . . . . . . . . . . . . 4
3. Requirements . . . . . . . . . . . . . . . . . . . . . . . . . 4
4. Topology-Transparent Zone . . . . . . . . . . . . . . . . . . 4
4.1. Overview of Topology-Transparent Zone . . . . . . . . . . 4
4.2. An Example of TTZ . . . . . . . . . . . . . . . . . . . . 5
4.2.1. Creation of a TTZ . . . . . . . . . . . . . . . . . . 5
5. Changes to OSPF Protocols . . . . . . . . . . . . . . . . . . 6
5.1. One Bit to Indicate an Internal TTZ Link . . . . . . . . . 7
5.2. A TTZ TLV in Router Information LSA . . . . . . . . . . . 8
6. Constructing Router LSA . . . . . . . . . . . . . . . . . . . 9
7. Establishing Adjacencies . . . . . . . . . . . . . . . . . . . 10
8. Distribution of LSAs . . . . . . . . . . . . . . . . . . . . . 11
8.1. Distribution of LSAs within TTZ . . . . . . . . . . . . . 11
8.2. Distribution of LSAs through TTZ . . . . . . . . . . . . . 11
9. Computation of Routing Table . . . . . . . . . . . . . . . . . 11
10. Operations . . . . . . . . . . . . . . . . . . . . . . . . . . 12
10.1. Configuring TTZ . . . . . . . . . . . . . . . . . . . . . 12
10.2. Smooth Migration to TTZ . . . . . . . . . . . . . . . . . 12
11. Security Considerations . . . . . . . . . . . . . . . . . . . 13
12. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 13
13. Acknowledgement . . . . . . . . . . . . . . . . . . . . . . . 13
14. References . . . . . . . . . . . . . . . . . . . . . . . . . . 14
14.1. Normative References . . . . . . . . . . . . . . . . . . . 14
14.2. Informative References . . . . . . . . . . . . . . . . . . 14
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 14
Chen, et al. Expires July 20, 2014 [Page 2]
Internet-Draft Topology-Transparent Zone January 2014
1. Introduction
The number of routers in a network becomes larger and larger as the
Internet traffic keeps growing. Through splitting the network into
multiple areas, we can extend the network further. However, there
are a number of issues when a network is split further into more
areas.
At first, dividing a network from one area into multiple areas or
from a number of existing areas to even more areas is a very
challenging and time consuming task since it is involved in
significant network architecture changes. Considering the one area
case, originally the network has only one area, which is the
backbone. This original backbone area will be split into a new
backbone and a number of non backbone areas. In general, each of the
non backbone areas is connected to the new backbone area through the
area border routers between the non backbone and the backbone area.
There is not any direct connection between any two non backbone
areas. Each area border router summarizes the topology of its
attached non backbone area for transmission on the backbone area, and
hence to all other area border routers.
Secondly, the services carried by the network may be interrupted
while the network is being split from one area into multiple areas or
from a number of existing areas into even more areas.
Furthermore, it is complex for a Multi-Protocol Label Switching
(MPLS) Traffic Engineering (TE) Label Switching Path (LSP) crossing
multiple areas to be setup. In one option, a TE path crossing
multiple areas is computed by using collaborating Path Computation
Elements (PCEs) [RFC5441] through the PCE Communication Protocol
(PCEP)[RFC5440], which is not easy to configure by operators since
the manual configuration of the sequence of domains is required.
Although this issue can be addressed by using the Hierarchical PCE,
this solution may further increase the complexity of network design.
Especially, the current PCE standard method may not guarantee that
the path found is optimal.
This document presents a topology-transparent zone in an area and
describes extensions to OSPF for supporting the topology-transparent
zone, which is scalable and resolves the issues above.
A topology-transparent zone comprises a group of routers and a number
of links connecting these routers. Any router outside of the zone is
not aware of the zone. The information about the links and routers
inside the zone is not distributed to any router outside of the zone.
Any link state change such as a link down inside the zone is not seen
by any router outside of the zone.
Chen, et al. Expires July 20, 2014 [Page 3]
Internet-Draft Topology-Transparent Zone January 2014
2. Conventions Used in This Document
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119.
3. Requirements
Topology-Transparent Zone (TTZ) may be deployed for resolving some
critical issues in existing networks and future networks. The
requirements for TTZ are listed as follows:
o TTZ MUST be backward compatible. When a TTZ is deployed on a set
of routers in a network, the routers outside of the TTZ in the
network do not need to know or support TTZ.
o TTZ MUST support at least one more levels of network hierarchies,
in addition to the hierarchies supported by existing routing
protocols.
o Users SHOULD be able to easily set up an end to end service
crossing TTZs.
o The configuration for a TTZ in a network SHOULD be minimum.
o The changes on the existing protocols for supporting TTZ SHOULD be
minimum.
4. Topology-Transparent Zone
4.1. Overview of Topology-Transparent Zone
A Topology-Transparent Zone (TTZ) is identified by an Identifier
(ID), and it includes a group of routers and a number of links
connecting the routers. A TTZ is in an OSPF area.
The ID of a Topology-Transparent Zone (TTZ) or TTZ ID is a number
that is unique for identifying an entity such as a node in an OSPF
domain. It is not zero in general.
In addition to having the functions of an OSPF area, an OSPF TTZ
makes some improvements on an OSPF area, which include:
o An OSPF TTZ is virtualized as a group of TTZ edge routers
connected.
Chen, et al. Expires July 20, 2014 [Page 4]
Internet-Draft Topology-Transparent Zone January 2014
o An OSPF TTZ receives the link state information about the topology
outside of the TTZ, stores the information in the TTZ and floods
the information through the TTZ to the routers outside of TTZ.
4.2. An Example of TTZ
4.2.1. Creation of a TTZ
The figure below illustrates an example of a routing area containing
a topology-transparent zone: TTZ 600.
TTZ 600
\
\ ^~^~^~^~^~^~^~^~^~^~^~^~
( )
===[R15]========(==[R61]------------[R63]==)======[R29]===
|| ( | \ / | ) ||
|| ( | \ / | ) ||
|| ( | \ / | ) ||
|| ( | ___\ / | ) ||
|| ( | / [R71] | ) ||
|| ( | [R73] / \ | ) ||
|| ( | / \ | ) ||
|| ( | / \ | ) ||
|| ( | / \ | ) ||
===[R17]========(==[R65]------------[R67]==)======[R31]===
\\ (// \\) //
|| //v~v~v~v~v~v~v~v~v~v~v~\\ ||
|| // \\ ||
|| // \\ ||
\\ // \\ //
======[R23]==============================[R25]=====
// \\
// \\
Figure 1: An Example of TTZ
The routing area comprises routers R15, R17, R23, R25, R29 and R31.
It also contains a topology-transparent zone TTZ 600. The TTZ 600
comprises routers R61, R63, R65, R67, R71 and R73, and the links
connecting them.
There are two types of routers in a TTZ: TTZ internal routers and TTZ
edge routers. A TTZ internal router is a router inside the TTZ and
every adjacent router of the TTZ internal router is a router inside
the TTZ. A TTZ edge router is a router inside the TTZ and has at
least one adjacent router that is outside of the TTZ.
Chen, et al. Expires July 20, 2014 [Page 5]
Internet-Draft Topology-Transparent Zone January 2014
The TTZ in the figure above comprises four TTZ edge routers R61, R63,
R65 and R67. Each TTZ edge router is connected to at least one
router outside of the TTZ. For instance, router R61 is a TTZ edge
router since it is connected to router R15, which is outside of the
TTZ.
In addition, the TTZ comprises two TTZ internal routers R71 and R73.
A TTZ internal router is not connected to any router outside of the
TTZ. For instance, router R71 is a TTZ internal router since it is
not connected to any router outside of the TTZ. It is just connected
to routers R61, R63, R65, R67 and R73 inside the TTZ.
A TTZ MUST hide the information inside the TTZ from the outside. It
MUST NOT directly distribute any internal information about the TTZ
to a router outside of the TTZ.
For instance, the TTZ in the figure above MUST NOT send the
information about TTZ internal router R71 to any router outside of
the TTZ in the routing domain; it MUST NOT send the information about
the link between TTZ router R61 and R65 to any router outside of the
TTZ.
In order to create a TTZ, we MUST configure the same TTZ ID on the
edge routers and identify the TTZ internal links on them. In
addition, we SHOULD configure the TTZ ID on every TTZ internal router
which indicates that every link of the router is a TTZ internal link.
From a router outside of the TTZ, a TTZ is seen as a group of routers
fully connected. For instance, router R15 in the figure above, which
is outside of TTZ 600, sees TTZ 600 as a group of TTZ edge routers:
R61, R63, R65 and R67. These four TTZ edge routers are fully
connected.
In addition, a router outside of the TTZ sees TTZ edge routers having
normal connections to the routers outside of the TTZ. For example,
router R15 sees four TTZ edge routers R61, R63, R65 and R67, which
have the normal connections to R15, R29, R17 and R23, R25 and R31
respectively.
5. Changes to OSPF Protocols
There are a number of ways to extend the existing OSPF protocol to
support TTZ. This section describes a couple of them.
o One way is to use one bit to indicate that a link is a TTZ link in
a router LSA.
Chen, et al. Expires July 20, 2014 [Page 6]
Internet-Draft Topology-Transparent Zone January 2014
o Another option is to have a TLV in a Router Information LSA
containing TTZ ID and flags to indicate that the router is a TTZ
edge router or a TTZ internal router.
5.1. One Bit to Indicate an Internal TTZ Link
A router LSA contains the description of a number of router links.
The existing format of a router LSA is illustrated as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| LS age | Options | 1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Link State ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Advertising Router |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| LS sequence number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| LS checksum | length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0 |V|E|B| 0 | # links |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Link ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Link Data |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | # TOS | metric |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TOS | 0 | TOS metric |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Link ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Link Data |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ... |
Figure 2: Format of Router LSA
For a router link, the value of an eight bit Type field indicates the
kind of the link. The value of the Type field may be 1, 2, 3 or 4,
which indicates that the kind of the link is a point-to-point
connection to another router, a connection to a transit network, a
connection to a stub network, or a virtual link respectively.
Chen, et al. Expires July 20, 2014 [Page 7]
Internet-Draft Topology-Transparent Zone January 2014
The existing eight bit Type field for a router link may be split into
two fields as follows:
0 1 2 3 4 5 6 7
+---+---+---+---+---+---+---+---+
| I | Type-1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
I bit flag:
1: This indicates that the router link is an internal link
to a router inside the TTZ.
0: This indicates that the router link is an external link.
Type-1:
The kind of the link.
Figure 3: Bit to Indicate Internal TTZ Link
For a link inside a TTZ, the value of I bit flag is set to one,
indicating that this link is an internal TTZ link. For a link
connecting to a router outside of a TTZ from a TTZ edge router, the
value of I bit flag is set to zero, indicating that this link is an
external TTZ link.
The value of Type-1 field may have value 1, 2, 3, or 4, which
indicates that the kind of a link being described is a point-to-point
connection to another router, a connection to a transit network, a
connection to a stub network, or a virtual link respectively.
5.2. A TTZ TLV in Router Information LSA
A new TLV is proposed in Router Information LSA for TTZ in the figure
below to indicate a router's TTZ capability and the TTZ to which the
router belongs.
Chen, et al. Expires July 20, 2014 [Page 8]
Internet-Draft Topology-Transparent Zone January 2014
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|E| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TTZ ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type A 16-bit field set to a number to be determined by IANA.
Length A 16-bit field indicating the length of the value, which
is 8.
Value E bit set to 1 indicating a TTZ edge router
0 indicating a TTZ internal router
TTZ ID gives the TTZ to which the router belongs
Figure 4: TTZ TLV in Router Information LSA
The TTZ TLV follows the Router Informational Capabilities TLV in a
Router Information LSA. Every edge router of a TTZ generates a
Router Information LSA containing a TTZ TLV with E bit set to 1 and
the ID of the TTZ. Each internal router of the TTZ originates a
Router Information LSA containing a TTZ TLV with E bit set to 0 and
the ID of the TTZ.
A TTZ is defined by all the routers with the same TTZ ID and all the
TTZ links. For a TTZ edge router, its links connected to other TTZ
routers belong to the TTZ. For a TTZ internal router, all its links
belong to the TTZ.
6. Constructing Router LSA
Two types of router LSAs are generated by an edge router of a TTZ.
The first type describes the links connecting to it; in fact, this
LSA is the "normal" LSA that would be constructed if the TTZ feature
is not used. This LSA is also generated by a router inside the TTZ.
The second is generated to virtualize the TTZ as a group of edge
routers connected.
The first type of LSA comprises both the router links connecting the
routers inside the TTZ and the router links connecting to the routers
Chen, et al. Expires July 20, 2014 [Page 9]
Internet-Draft Topology-Transparent Zone January 2014
outside of the TTZ. For each of the router links in the LSA, it can
be represented in one of the ways described in the previous section.
The second router LSA generated by an edge router of the TTZ
comprises two groups of links in general.
The first group of links are the router links connecting the routers
outside of the TTZ from this TTZ edge router. These router links are
normal router links. There is a router link for every adjacency
between this TTZ edge router and a router outside of the TTZ.
The second group of links are the "virtual" router links. For each
of the other TTZ edge routers, there is a "virtual" router link to it
from this TTZ edge router. The cost of the router link from this TTZ
router to one of the other TTZ edge routers may be the cost of the
shortest path from this TTZ edge router to it.
In addition, the LSA may contain a third group of links, which are
stub links for other destinations inside the TTZ. They may be the
loopback addresses to be accessed by a node outside of the TTZ.
7. Establishing Adjacencies
A router in a TTZ forms an adjacency with another router in the TTZ
in the same way as a normal router when these two routers have a
connection.
For an edge router in a TTZ, it also forms an adjacency with any
router outside of the TTZ that has a connection with the edge router.
When the edge router synchronizes its link state database with the
router outside of the TTZ, it sends the router outside of the TTZ the
information about all the LSAs except for the LSAs belonging to the
TTZ that are hidden from any router outside of the TTZ.
At the end of the link state database synchronization, the edge
router originates its own router LSA for virtualizing the TTZ and
sends this LSA to the router outside of the TTZ.
From the point of view of the router outside of the TTZ, it sees the
other end as a normal router and forms the adjacency in the same way
as a normal router. It is not aware of anything about its
neighboring TTZ. From the LSAs related to the TTZ edge router in the
other end, it knows that the TTZ edge router is connected to each of
the other TTZ edge routers and some routers outside of the TTZ.
Chen, et al. Expires July 20, 2014 [Page 10]
Internet-Draft Topology-Transparent Zone January 2014
8. Distribution of LSAs
LSAs can be divided into a couple of classes according to their
distributions. The first class of LSAs is distributed within a TTZ.
The second is distributed through a TTZ.
8.1. Distribution of LSAs within TTZ
Any LSA about a link state in a TTZ is distributed within the TTZ.
It will not be distributed to any router outside of the TTZ.
For example, any router LSA generated for a router in a TTZ is
distributed within the TTZ. It will not be distributed to any router
outside of the TTZ.
Any network LSA generated for a broadcast or NBMA network inside a
TTZ is distributed within the TTZ. It will not be distributed to any
router outside of the TTZ.
Any opaque LSA generated for a TTZ internal TE link is distributed
within the TTZ. It will not be distributed to any router outside of
the TTZ.
8.2. Distribution of LSAs through TTZ
Any LSA about a link state outside of a TTZ received by an edge
router of the TTZ is distributed through the TTZ.
For example, when an edge router of a TTZ receives an LSA for a link
state outside of the TTZ from a router outside of the TTZ, it floods
it to its neighboring routers both inside the TTZ and outside of the
TTZ. This LSA may be any LSA such as a router LSA and an opaque LSA
that is distributed in a domain.
The routers in the TTZ continue to flood the LSA. When another edge
router of the TTZ receives the LSA, it floods the LSA to its
neighboring routers both outside of the TTZ and inside the TTZ.
9. Computation of Routing Table
The computation of the routing table on a router is the same as that
described in RFC 2328, with one exception. An edge router of a TTZ
MUST ignore the router LSAs generated by the edge routers of the TTZ
for virtualizing the TTZ.
Chen, et al. Expires July 20, 2014 [Page 11]
Internet-Draft Topology-Transparent Zone January 2014
10. Operations
As described above, only the edge routers of the TTZ are aware of any
changes in the operation of the domain.
10.1. Configuring TTZ
This section proposes a few of options for configuring a TTZ.
1. Configuring TTZ on Every Link in TTZ
If every link in a TTZ is configured with a same TTZ ID as a TTZ
link, the TTZ is determined. A router with some TTZ links and some
normal links is a TTZ edge router. A router with only TTZ links is a
TTZ internal router.
2. Configuring TTZ on Every Router in TTZ
We may configure a same TTZ ID on every router in the TTZ, and on
every edge router's links connecting to the routers in the TTZ.
A router configured with the TTZ ID on some of its links is a TTZ
edge router. A router configured with the TTZ ID only is a TTZ
internal router. All the links on a TTZ internal router are TTZ
links.
This option is simpler than the above one.
3. Configuring TTZ on Edge Routers
We may configure a same TTZ ID on every edge router of the TTZ and on
every edge router's links connectting the routers in the TTZ.
A router is a TTZ router if it is connected to another TTZ router.
For a TTZ internal router, all its links are TTZ links. A TTZ
comprises all the TTZ edge routers configured, the TTZ internal
routers, and the TTZ links.
This option is simpler than the above two options.
10.2. Smooth Migration to TTZ
This section describes the mechanisms which allow users to make a
smooth migration to the TTZ with minimum interruption to the network.
For a group of routers and a number of links connecting the routers
in an area, making them to work as a TTZ eventually with minimum
interruption to the network may take a few of steps or stages.
Chen, et al. Expires July 20, 2014 [Page 12]
Internet-Draft Topology-Transparent Zone January 2014
At first, users configure the TTZ feature on the edge routers of the
TTZ. In this stage, the router has dual roles. One role is to
function as a normal router. The other is to generate and distribute
some TTZ information among the routers in the TTZ.
Secondly, users SHOULD check whether every router in the TTZ is ready
for transferring to work as a TTZ router. A router in the TTZ is
ready after it has received all the necessary information from all
the routers in the TTZ. This information may be displayed on a
router through a CLI command.
And then users may activate the TTZ. There are a few of ways to
activate the TTZ. One way is to activate it on a TTZ router through
a CLI command such as activate TTZ directly. Another is through a
TTZ activate timer, which activates the TTZ once the timer expires.
After a TTZ router is requested to activate the TTZ, it transfers to
work as a TTZ router. When a TTZ router receives a LSA for
virtualizing the TTZ, it also transfers to work as a TTZ router.
Thus, activating the TTZ on one TTZ router will make every router in
the TTZ transfer to work as a TTZ router.
For an edge router of the TTZ, transferring to work as a TTZ router
comprises generating a router LSA to virtualize the TTZ and flooding
this LSA to all its neighboring routers.
11. Security Considerations
The mechanism described in this document does not raise any new
security issues for the OSPF protocols.
12. IANA Considerations
IANA is asked to assign a TLV in the OSPF Router Informational LSA,
as described in Section 5.
13. Acknowledgement
The author would like to thank Acee Lindem, Dean Cheng, Russ White,
William McCall, Tony Przygienda, Lin Han and Yang Yu for their
valuable comments on this draft.
14. References
Chen, et al. Expires July 20, 2014 [Page 13]
Internet-Draft Topology-Transparent Zone January 2014
14.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2328] Moy, J., "OSPF Version 2", STD 54, RFC 2328, April 1998.
[RFC4970] Lindem, A., Shen, N., Vasseur, JP., Aggarwal, R., and S.
Shaffer, "Extensions to OSPF for Advertising Optional
Router Capabilities", RFC 4970, July 2007.
[RFC2740] Coltun, R., Ferguson, D., and J. Moy, "OSPF for IPv6",
RFC 2740, December 1999.
14.2. Informative References
[RFC5441] Vasseur, JP., Zhang, R., Bitar, N., and JL. Le Roux, "A
Backward-Recursive PCE-Based Computation (BRPC) Procedure
to Compute Shortest Constrained Inter-Domain Traffic
Engineering Label Switched Paths", RFC 5441, April 2009.
[RFC5440] Vasseur, JP. and JL. Le Roux, "Path Computation Element
(PCE) Communication Protocol (PCEP)", RFC 5440,
March 2009.
Authors' Addresses
Huaimo Chen
Huawei Technologies
Boston, MA
USA
Email: huaimo.chen@huawei.com
Renwei Li
Huawei Technologies
2330 Central expressway
Santa Clara, CA
USA
Email: renwei.li@huawei.com
Chen, et al. Expires July 20, 2014 [Page 14]
Internet-Draft Topology-Transparent Zone January 2014
Gregory Cauchie
FRANCE
Email: greg.cauchie@gmail.com
Alvaro Retana
Cisco Systems, Inc.
7025 Kit Creek Rd.
Raleigh, NC 27709
USA
Email: aretana@cisco.com
Ning So
Tata Communications
2613 Fairbourne Cir.
Plano, TX 75082
USA
Email: ning.so@tatacommunications.com
Mehmet Toy
Comcast
1800 Bishops Gate Blvd.
Mount Laurel, NJ 08054
USA
Email: mehmet_toy@cable.comcast.com
Lei Liu
UC Davis
CA
USA
Email: liulei.kddi@gmail.com
Chen, et al. Expires July 20, 2014 [Page 15]