Internet Engineering Task Force                            T. Stach, Ed.
Internet-Draft                                                 A. Hutton
Intended status: Informational         Siemens Enterprise Communications
Expires: September 12, 2013                                    J. Uberti
                                                                  Google
                                                          March 11, 2013


       RTCWEB Considerations for NATs, Firewalls and HTTP proxies
           draft-hutton-rtcweb-nat-firewall-considerations-00

Abstract

   This document describes mechanism to enable media stream
   establishment in the presence of NATs, firewalls and HTTP proxies.
   HTTP proxy and firewall policies applied in many private network
   domains introduce obstacles to the successful establishment of media
   stream via RTCWEB.  This document examines some of these policies and
   develops requirements on the web browsers designed to provide the
   best possible chance of media connectivity between RTCWEB peers.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at http://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on September 12, 2013.

Copyright Notice

   Copyright (c) 2013 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect



Stach, et al.          Expires September 12, 2013               [Page 1]


Internet-Draft               RTCWEB NAT-FW                    March 2013


   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   2
     1.1.  Requirements Language . . . . . . . . . . . . . . . . . .   3
   2.  Considerations for NATs/Firewalls independent of HTTP proxies   3
     2.1.  Firewall open for outgoing UDP and TCP traffic  . . . . .   3
     2.2.  Firewall open only for TCP traffic  . . . . . . . . . . .   4
     2.3.  Firewall open only for TCP-based HTTP(s) traffic  . . . .   4
   3.  Considerations for NATs/Firewalls in presence of HTTP proxies   4
     3.1.  HTTP proxy with NAT/firewall open for outgoing UDP and
           TCP traffic . . . . . . . . . . . . . . . . . . . . . . .   4
     3.2.  HTTP proxy with NAT/firewall open only for TCP traffic  .   5
     3.3.  HTTP proxy assisted TURN server connection  . . . . . . .   5
       3.3.1.  TURN server connection via TCP  . . . . . . . . . . .   5
       3.3.2.  TURN server connection via UDP  . . . . . . . . . . .   6
   4.  Requirements for RTCWEB-enabled browsers  . . . . . . . . . .   6
   5.  Acknowledgements  . . . . . . . . . . . . . . . . . . . . . .   7
   6.  IANA Considerations . . . . . . . . . . . . . . . . . . . . .   7
   7.  Security Considerations . . . . . . . . . . . . . . . . . . .   7
   8.  References  . . . . . . . . . . . . . . . . . . . . . . . . .   7
     8.1.  Normative References  . . . . . . . . . . . . . . . . . .   7
     8.2.  Informative References  . . . . . . . . . . . . . . . . .   7
   Appendix A.  Additional Stuff . . . . . . . . . . . . . . . . . .   8
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .   8

1.  Introduction

   Many organizations, e.g.  an enterprise, a public service agency or a
   university, deploy NATs and firewalls at the border to the public
   internet.  RTCWEB relies on ICE [RFC5245] in order to establish a
   media path between two RTCWEB peers in the presence of such NATs/FWs.
   As last resort in order to cater for NAT/FWs with address and port
   dependent filtering characteristics [RFC4787], the peers will
   introduce a TURN server [RFC5766] in the public internet as a media
   relay.  Aspects of TURN server deployment in the RTCWEB environment
   are also considered in [draft-ietf-rtcweb-use-cases-and-requirements]

   If an organization wants to support RTCWEB such a TURN server may be
   located in the DMZ of the private network of that organization where
   it is still under administrative control.

   In certain environments with very restrictive FW policies a TURN
   server in the public internet may not be sufficient to establish



Stach, et al.          Expires September 12, 2013               [Page 2]


Internet-Draft               RTCWEB NAT-FW                    March 2013


   connectivity towards the RTCWEB peer for RTP-based media [RFC3550].
   Such policies can include blocking of all UDP based traffic and
   allowing only HTTP(S) traffic to the TCP ports 80/443.  In addition
   access to the World Wide Web from inside an organization is often
   only possible via a HTTP proxy.

   This document examines impact of NAT/FW policies in Section 2.
   Additional impacts due to the presence of a HTTP proxy are examined
   in Section 3.

1.1.  Requirements Language

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in RFC 2119 [RFC2119].

2.  Considerations for NATs/Firewalls independent of HTTP proxies

   This section covers aspects of how NAT/FW characteristic influence
   the establishement of a media stream.  Additional aspects introduced
   by the presence of a HTTP proxy are covered in Section 3.

   If the NAT shows port and address dependent filtering behavior there
   is the need for a TURN server arises in order to establish
   connectivity for media streams.  The TURN server will relay the RTP
   packet to the RTCWEB peer using UDP.  How the RTP packets are sent
   from the RTCWEB client within the private network to the TURN server
   depends on what the firewall will let pass through.

   Other types of NATs do not require using the TURN relay.
   Nevertheless, the FW rules and policies still affect how media
   streams can be established.

2.1.  Firewall open for outgoing UDP and TCP traffic

   This scenario assumes that the NAT/FW is transparent for all outgoing
   traffic independent of using UDP or TCP as transport protocol.  This
   case is used as starting point for introduction of a more restrictive
   firewall.  It presents the least critical example with respect to the
   establishment of the media streams.

   The TURN server can be reached directly from within via the NAT/FW
   and the ICE procedures will reveal that media can be sent via the
   TURN server.  The TURN client will send its media to the allocated
   resources at the TURN server via UDP.






Stach, et al.          Expires September 12, 2013               [Page 3]


Internet-Draft               RTCWEB NAT-FW                    March 2013


   Dependent on the port range that is used for RTCWEB media streams,
   the same statement would be true if the NAT/Firewall would allow UDP
   traffic for that ports only.

2.2.  Firewall open only for TCP traffic

   This scenario assumes that the NAT/FW is transparent for outgoing
   traffic only using TCP as transport protocol.  This gives two options
   for media stream establishment dependent on the NAT's filering
   characteristics.  Either transport RTP over TCP or contacting the
   TURN server via TCP.

   In the first case the browser needs use ICE-TCP [RFC6544] and could
   launch a successful connectivity check directly to the remote
   endpoint.

   In the second case the browser needs to contact the TURN server via
   TCP for allocation of an UDP-based relay address at the TURN server.
   The ICE procedures will reveal that RTP media can be sent via the
   TURN relay using the TCP connection between TURN client and TURN
   server.

   The TURN server would then relay the RTP packets using UDP.  ICE-TCP
   [RFC6544] is not needed in this context.

2.3.  Firewall open only for TCP-based HTTP(s) traffic

   In this case the firewall blocks all outgoing traffic except for TCP
   traffic to port 80 for HTTP or 443 for HTTPS.  A TURN server
   listening to its default ports (3478 for TCP/UDP, 5349 for TLS) would
   not be reachable in this case.

   However, the TURN server could still be reached when it is configured
   to listen to the HTTP(S) ports as well.  In addition the RTCWEB
   clients need to be configured to contact the TURN server over the
   HTTP(S) ports.

3.  Considerations for NATs/Firewalls in presence of HTTP proxies

   This section considers a scenario where all HTTP(S) traffic is routed
   via an HTTP proxy.  Note: If both RTCWEB clients are located behind
   the same HTTP proxies, we, of course, assume that ICE would give us a
   direct media connection within the private network.  We consider this
   case as out of the scope of this document.

3.1.  HTTP proxy with NAT/firewall open for outgoing UDP and TCP traffic





Stach, et al.          Expires September 12, 2013               [Page 4]


Internet-Draft               RTCWEB NAT-FW                    March 2013


   As in Section 2.1 we assume that the NAT/FW is transparent for all
   outgoing traffic independent of using UDP or TCP as transport
   protocol.  Consequently, the same considerations as in Section 2.1
   apply with respect to the traversal of the NAT/FW.

3.2.  HTTP proxy with NAT/firewall open only for TCP traffic

   As in Section 2.2 we assume that the NAT/FW is transparent only for
   outgoing TCP traffic Consequently, the same consideration as in
   Section 2.2 apply with respect to the traversal of the NAT/FW.

3.3.  HTTP proxy assisted TURN server connection

3.3.1.  TURN server connection via TCP

   Different from the previous scenarios, we assume that the NAT/FW
   accepts outgoing traffic only via a TCP connection that is initiated
   from the HTTP proxy.  Consequently, a RTCWEB client would have to use
   the HTTP CONNECT method in order to get access to the TURN server via
   the HTTP proxy.  The HTTP CONNECT request needs to convey the TURN
   Server URI or transport address.  Afterwards, the RTCWEB client could
   upgrade the connection to use TLS, forward STUN/TURN traffic via the
   HTTP proxy and use the TURN server as media relay.

   If it is not possible to use HTTP CONNECT in this way, WebRTC will
   not work.  We consider this case as out of the scope of this
   document.

   Strictly speaking the TLS upgrade is not necessary, but using TLS
   would also prevent the HTTP proxy from sniffing into the data stream
   and provides the same flow as HTTPS and might improve
   interoperability with proxy servers.  Some tests (done a while ago)
   indicated that there are DPI proxies that expect to see at least a
   SSL handshake and, possibly, valid SSL records.  The application has
   the ability to control whether SSL is used by the parameters it
   supplies to the TURN URI (e.g.  turns: vs turn:), so the decision to
   do TURN/TCP to port 443 versus TURN/TLS to port 443 could be left up
   to the application.













Stach, et al.          Expires September 12, 2013               [Page 5]


Internet-Draft               RTCWEB NAT-FW                    March 2013


   In contrast to using UDP or TCP for transport of STUN messages, the
   browser would now need to first establish a HTTP over TCP connection
   to the HTTP proxy, upgrade to using TLS and then switch to using this
   TLS connection for transport of STUN messages.  It is also desirable
   that the browser detects the need to connect to the TURN server
   through a HTTP proxy automatically in order to achieve seamless
   deployment and interoperability.  The browser should use the same
   proxy selection procedure for TURN as currently done for HTTP.  The
   user or network administrator should not be required to change
   browser or proxy script configuration.

3.3.2.  TURN server connection via UDP

   If a local TURN server under administrative control of the
   organization is deployed it is desirable to reach this TURN server
   via UDP.  The TURN server could be specified in the proxy
   configuration script, giving the browser the possibility to learn how
   to access it.  Then, when gathering candidates, this TURN server
   would always be used such the RTCWWEB client application could get
   UDP traffic out to the internet.

4.  Requirements for RTCWEB-enabled browsers

   For the purpose of relaying RTCWEB media streams or data channels a
   browser needs to be able to

   - connect to a TURN server via UDP, TCP and TLS for the purpose of
   relaying RTCWEB media streams or data channels

   - connect to a TURN server via a HTTP proxy using the HTTP connect
   method

   - connect to a TURN server via the HTTP(s) ports 80/443 instead of
   the default STUN ports 3478/5349.

   - upgrade the HTTP proxy-relayed connection to the TURN server to use
   TLS

   - use the same proxy selection procedure for TURN as currently done
   for HTTP

   - switch the usage of the HTTP proxy-relayed connection with the TURN
   server from HTTP to STUN/TURN in order to relay media streams or data
   channels.

   - to use a preconfigured or standardized port range for UPD-based
   media streams or data channels.




Stach, et al.          Expires September 12, 2013               [Page 6]


Internet-Draft               RTCWEB NAT-FW                    March 2013


   - learn from the proxy configuration script about the presence of a
   local TURN server and use it for sending UDP traffic to the internet.

   - support ICE-TCP for TCP-based direct media connection to the RTCWEB
   peer.

5.  Acknowledgements

   The authors want to thank Heinrich Haager for all his input during
   many valuable discussions.

6.  IANA Considerations

   This memo includes no request to IANA.

7.  Security Considerations

   TBD

8.  References

8.1.  Normative References

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119, March 1997.

8.2.  Informative References

   [RFC3550]  Schulzrinne, H., Casner, S., Frederick, R., and V.
              Jacobson, "RTP: A Transport Protocol for Real-Time
              Applications", STD 64, RFC 3550, July 2003.

   [RFC4787]  Audet, F. and C. Jennings, "Network Address Translation
              (NAT) Behavioral Requirements for Unicast UDP", BCP 127,
              RFC 4787, January 2007.

   [RFC5245]  Rosenberg, J., "Interactive Connectivity Establishment
              (ICE): A Protocol for Network Address Translator (NAT)
              Traversal for Offer/Answer Protocols", RFC 5245, April
              2010.

   [RFC5766]  Mahy, R., Matthews, P., and J. Rosenberg, "Traversal Using
              Relays around NAT (TURN): Relay Extensions to Session
              Traversal Utilities for NAT (STUN)", RFC 5766, April 2010.

   [RFC6544]  Rosenberg, J., Keranen, A., Lowekamp, B.B., and A.B.
              Roach, "TCP Candidates with Interactive Connectivity
              Establishment (ICE)", RFC 6544, March 2012.



Stach, et al.          Expires September 12, 2013               [Page 7]


Internet-Draft               RTCWEB NAT-FW                    March 2013


   [draft-ietf-rtcweb-use-cases-and-requirements]
              C. Holmberg, S. Hakansson, G. Eriksson , "Web Real-Time
              Communication Use-cases and Requirements ", 2012, <http://
              tools.ietf.org/html/draft-ietf-rtcweb-use-cases-and-
              requirements>.

Appendix A.  Additional Stuff

   This becomes an Appendix.

Authors' Addresses

   Thomas Stach (editor)
   Siemens Enterprise Communications
   Dietrichgasse 27-29
   Vienna  1030
   AT

   Email: thomas.stach@siemens-enterprise.com


   Andrew Hutton
   Siemens Enterprise Communications
   Technology Drive
   Nottingham  NG9 1LA
   UK

   Email: andrew.hutton@siemens-enterprise.com


   Justin Uberti
   Google
   5 Cambridge Center
   Cambridge, MA  02142
   US

   Email: justin@uberti.name













Stach, et al.          Expires September 12, 2013               [Page 8]