BESS Working Group Ali Sajassi
Internet-Draft Samir Thoria
Intended Status: Standards Track Cisco
Keyur Patel
Derek Yeung
Arrcus
John Drake
Wen Lin
Juniper
Expires: December 12, 2019 June 10, 2019
IGMP and MLD Proxy for EVPN
draft-ietf-bess-evpn-igmp-mld-proxy-03
Abstract
Ethernet Virtual Private Network (EVPN) solution [RFC 7432] is
becoming pervasive in data center (DC) applications for Network
Virtualization Overlay (NVO) and DC interconnect (DCI) services, and
in service provider (SP) applications for next generation virtual
private LAN services.
This draft describes how to support efficiently endpoints running
IGMP for the above services over an EVPN network by incorporating
IGMP proxy procedures on EVPN PEs.
Status of this Memo
This Internet-Draft is submitted to IETF in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as
Internet-Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/1id-abstracts.html
Sajassi et al. Expires December 12, 2019 [Page 1]
INTERNET DRAFT IGMP Reports Aggregation in EVPN June 10, 2019
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html
Copyright and License Notice
Copyright (c) 2018 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.1 Terminology . . . . . . . . . . . . . . . . . . . . . . . . 5
2 IGMP Proxy . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.1 Proxy Reporting . . . . . . . . . . . . . . . . . . . . . . 6
2.1.1 IGMP Membership Report Advertisement in BGP . . . . . . 7
2.1.1 IGMP Leave Group Advertisement in BGP . . . . . . . . . 8
2.2 Proxy Querier . . . . . . . . . . . . . . . . . . . . . . . 9
3 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.1 PE with only attached hosts/VMs for a given subnet . . . . . 10
3.2 PE with mixed of attached hosts/VMs and multicast source . . 11
3.3 PE with mixed of attached hosts/VMs, multicast source and
router . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4 All-Active Multi-Homing . . . . . . . . . . . . . . . . . . . . 11
4.1 Local IGMP Join Synchronization . . . . . . . . . . . . . . 11
4.2 Local IGMP Leave Group Synchronization . . . . . . . . . . . 12
4.2.1 Remote Leave Group Synchronization . . . . . . . . . . . 13
4.2.2 Common Leave Group Synchronization . . . . . . . . . . . 13
4.3 Mass Withdraw of Multicast join Sync route in case of
failure . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5 Single-Active Multi-Homing . . . . . . . . . . . . . . . . . . . 14
6 Selective Multicast Procedures for IR tunnels . . . . . . . . . 14
7 BGP Encoding . . . . . . . . . . . . . . . . . . . . . . . . . . 15
7.1 Selective Multicast Ethernet Tag Route . . . . . . . . . . . 15
7.1.1 Constructing the Selective Multicast Ethernet Tag
route . . . . . . . . . . . . . . . . . . . . . . . . . 17
Sajassi et al. Expires December 12, 2019 [Page 2]
INTERNET DRAFT IGMP Reports Aggregation in EVPN June 10, 2019
7.1.2 Default Selective Multicast Route . . . . . . . . . . . 18
7.2 Multicast Join Synch Route . . . . . . . . . . . . . . . . 19
7.2.1 Constructing the Multicast Join Synch Route . . . . . . 21
7.3 Multicast Leave Synch Route . . . . . . . . . . . . . . . . 22
7.3.1 Constructing the Multicas Leave Synch Route . . . . . . 24
7.4 Multicast Flags Extended Community . . . . . . . . . . . . . 25
7.5 EVI-RT Extended Community . . . . . . . . . . . . . . . . . 26
7.6 Rewriting of RT ECs and EVI-RT ECs by ASBRs . . . . . . . . 28
8 IGMP/MLD Immediate leave . . . . . . . . . . . . . . . . . . . 28
9 IGMP Version 1 membership request . . . . . . . . . . . . . . . 29
10 Security Considerations . . . . . . . . . . . . . . . . . . . 29
11 IANA Considerations . . . . . . . . . . . . . . . . . . . . . 29
12 References . . . . . . . . . . . . . . . . . . . . . . . . . . 30
12.1 Normative References . . . . . . . . . . . . . . . . . . . 30
12.2 Informative References . . . . . . . . . . . . . . . . . . 30
13 Acknowledgement . . . . . . . . . . . . . . . . . . . . . . . 30
14 Contributors . . . . . . . . . . . . . . . . . . . . . . . . . 30
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 30
Sajassi et al. Expires December 12, 2019 [Page 3]
INTERNET DRAFT IGMP Reports Aggregation in EVPN June 10, 2019
1 Introduction
Ethernet Virtual Private Network (EVPN) solution [RFC 7432] is
becoming pervasive in data center (DC) applications for Network
Virtualization Overlay (NVO) and DC interconnect (DCI) services, and
in service provider (SP) applications for next generation virtual
private LAN services.
In DC applications, a point of delivery (POD) can consist of a
collection of servers supported by several top of rack (TOR) and
Spine switches. This collection of servers and switches are self
contained and may have their own control protocol for intra-POD
communication and orchestration. However, EVPN is used as way of
standard inter-POD communication for both intra-DC and inter-DC. A
subnet can span across multiple PODs and DCs. EVPN provides robust
multi-tenant solution with extensive multi-homing capabilities to
stretch a subnet (e.g., VLAN) across multiple PODs and DCs. There can
be many hosts/VMs (e.g., several hundreds) attached to a subnet that
is stretched across several PODs and DCs.
These hosts/VMs express their interests in multicast groups on a
given subnet/VLAN by sending IGMP membership reports (Joins) for
their interested multicast group(s). Furthermore, an IGMP router
periodically sends membership queries to find out if there are hosts
on that subnet still interested in receiving multicast traffic for
that group. The IGMP/MLD Proxy solution described in this draft has
three objectives to accomplish:
1) Reduce flooding of IGMP messages: just like ARP/ND suppression
mechanism in EVPN to reduce the flooding of ARP messages over EVPN,
it is also desired to have a mechanism to reduce the flood of IGMP
messages (both Queries and Reports) in EVPN.
2) Distributed anycast multicast proxy: it is desired for the EVPN
network to act as a distributed anycast multicast router with respect
to IGMP/MLD proxy function for all the hosts attached to that
subnet.
3) Selective Multicast: to forward multicast traffic over EVPN
network such that it only gets forwarded to the PEs that have
interest in the multicast group(s) - i.e., multicast traffic will not
be forwarded to the PEs that have no receivers attached to them for
that multicast group. This draft shows how this objective may be
achieved when Ingress Replication is used to distribute the multicast
traffic among the PEs. Procedures for supporting selective multicast
using P2MP tunnels can be found in [bum-procedure-updates]
The first two objectives are achieved by using IGMP/MLD proxy on the
Sajassi et al. Expires December 12, 2019 [Page 4]
INTERNET DRAFT IGMP Reports Aggregation in EVPN June 10, 2019
PE and the third objective is achieved by setting up a multicast
tunnel (e.g., ingress replication) only among the PEs that have
interest in that multicast group(s) based on the trigger from
IGMP/MLD proxy processes. The proposed solutions for each of these
objectives are discussed in the following sections.
1.1 Terminology
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL
NOT","SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY",
and "OPTIONAL" in this document are to be interpreted as described in
BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all
capitals, as shown here.
POD: Point of Delivery
ToR: Top of Rack
NV: Network Virtualization
NVO: Network Virtualization Overlay
VNI: Virtual Network Identifier (for VXLAN)
EVPN: Ethernet Virtual Private Network
IGMP: Internet Group Management Protocol
MLD: Multicast Listener Discovery
EVI: An EVPN instance spanning the Provider Edge (PE) devices
participating in that EVPN
MAC-VRF: A Virtual Routing and Forwarding table for Media Access
Control (MAC) addresses on a PE
Ethernet Segment (ES): When a customer site (device or network) is
connected to one or more PEs via a set of Ethernet links, then that
set of links is referred to as an 'Ethernet segment'.
Ethernet Segment Identifier (ESI): A unique non-zero identifier that
identifies an Ethernet segment is called an 'Ethernet Segment
Identifier'.
PE: Provider Edge device.
BD: Broadcast Domain. As per [RFC7432], an EVI consists of a single
Sajassi et al. Expires December 12, 2019 [Page 5]
INTERNET DRAFT IGMP Reports Aggregation in EVPN June 10, 2019
or multiple BDs. In case of VLAN-bundle and VLAN-based service models
VLAN-aware bundle service model, an EVI contains multiple BDs. Also,
in this document, BD and subnet are equivalent terms.
Ethernet Tag: An Ethernet tag identifies a particular broadcast
domain, e.g., a VLAN. An EVPN instance consists of one or more
broadcast domains.
Single-Active Redundancy Mode: When only a single PE, among all the
PEs attached to an Ethernet segment, is allowed to forward traffic
to/from that Ethernet segment for a given VLAN, then the Ethernet
segment is defined to be operating in Single-Active redundancy mode.
All-Active Redundancy Mode: When all PEs attached to an Ethernet
segment are allowed to forward known unicast traffic to/from that
Ethernet segment for a given VLAN, then the Ethernet segment is
defined to be operating in All-Active redundancy mode.
This document also assumes familiarity with the terminology of
[RFC7432]. Though most of the place this document uses term IGMP
membership request (Joins), it MUST be considered true for MLD
membership request too. IGMPv2 corresponds to MLDv1 & IGMPv3
corresponds to MLDv2.
2 IGMP Proxy
IGMP Proxy mechanism is used to reduce the flooding of IGMP messages
over EVPN network similar to ARP proxy used in reducing the flooding
of ARP messages over EVPN. It also provides triggering mechanism for
the PEs to setup their underlay multicast tunnels. IGMP Proxy
mechanism consist of two components: a) Proxy for IGMP Reports and b)
Proxy for IGMP Queries.
2.1 Proxy Reporting
When IGMP protocol is used between host/VMs and its first hop EVPN
router (EVPN PE), Proxy-reporting is used by the EVPN PE to summarize
(when possible) reports received from downstream hosts and propagate
it in BGP to other PEs that are interested in the information. This
is done by terminating IGMP Reports in the first hop PE, translating
and exchanging the relevant information among EVPN BGP speakers. The
information is again translated back to IGMP message at the recipient
EVPN speaker. Thus it helps create an IGMP overlay subnet using BGP.
In order to facilitate such an overlay, this document also defines a
new EVPN route type NLRI, EVPN Selective Multicast Ethernet Tag
route, along with its procedures to help exchange and register IGMP
multicast groups [section 5].
Sajassi et al. Expires December 12, 2019 [Page 6]
INTERNET DRAFT IGMP Reports Aggregation in EVPN June 10, 2019
2.1.1 IGMP Membership Report Advertisement in BGP
When a PE wants to advertise an IGMP membership report (Join) using
the BGP EVPN route, it follows the following rules:
1) When the first hop PE receives several IGMP membership reports
(Joins) , belonging to the same IGMP version, from different attached
hosts/VMs for the same (*,G) or (S,G), it only sends a single BGP
message corresponding to the very first IGMP Join. This is because
BGP is a statefull protocol and no further transmission of the same
report is needed. If the IGMP Join is for (*,G), then multicast group
address along with the corresponding version flag (v2 or v3) are set.
In case of IGMPv3, exclude flag also needs to be set to indicate that
no source IP address to be excluded (e.g., include all sources "*").
If the IGMP Join is for (S,G), then besides setting multicast group
address along with the version flag v3, the source IP address and the
include/exclude flag must be set. It should be noted that when
advertising the EVPN route for (S,G), the only valid version flag is
v3 (i.e., v1 and v2 flags must be set to zero).
2) When the first hop PE receives an IGMPv3 Join for (S,G) on a given
BD, it advertises the corresponding EVPN Selective Multicast Ethernet
Tag (SMET) route regardless of whether the source (S) is attached to
itself or not in order to facilitate the source move in the future.
3) When the first hop PE receives an IGMP version-X Join first for
(*,G) and then later it receives an IGMP version-Y Join for the same
(*,G), then it will re-advertise the same EVPN SMET route with flag
for version-Y set in addition to any previously-set version flag(s).
In other words, the first hop PE does not withdraw the EVPN route
before sending the new route because the flag field is not part of
BGP route key processing.
4) When the first hop PE receives an IGMP version-X Join first for
(*,G) and then later it receives an IGMPv3 Join for the same
multicast group address but for a specific source address S, then the
PE will advertise a new EVPN SMET route with v3 flag set (and v1 and
v2 reset). Include/exclude flag also need to be set accordingly.
Since source IP address is used as part of BGP route key processing,
it is considered as a new BGP route advertisement.
5) When a PE receives an EVPN SMET route with more than one version
flag set, it will generate the corresponding IGMP report for (*,G)
for each version specified in the flag field. With multiple version
flags set, there MUST not be source IP address in the receive EVPN
route. If there is, then an error SHOULD be logged. If v3 flag is set
Sajassi et al. Expires December 12, 2019 [Page 7]
INTERNET DRAFT IGMP Reports Aggregation in EVPN June 10, 2019
(in addition to v2), then the include/exclude flag MUST indicate
"exclude". If not, then an error SHOULD be logged. The PE MUST
generate an IGMP membership report (Join) for that (*,G) and each
IGMP version in the version flag.
6) When a PE receives a list of EVPN SMET NLRIs in its BGP update
message, each with a different source IP address and the same
multicast group address, and the version flag is set to v3, then the
PE generates an IGMPv3 membership report with a record corresponding
to the list of source IP addresses and the group address along with
the proper indication of inclusion/exclusion.
7) Upon receiving EVPN SMET route(s) and before generating the
corresponding IGMP Join(s), the PE checks to see whether it has any
CE multicast router for that BD on any of its ES's . The PE provides
such check by listening for PIM hellos on that AC (i.e, <ES,BD>). If
it has router's ACs, then the generated IGMP Join(s) are sent to
those ACs. If it doesn't have any router's AC, then no IGMP Join(s)
needs to be generated because sending IGMP Joins to other hosts can
result in unintentionally preventing a host from joining a specific
multicast group for IGMPv2 - i.e., if the PE does not receive a join
from the host it will not forward multicast data to it. Per
[RFC4541], when an IGMPv2 host receives a membership report for a
group address that it intends to join, the host will suppress its own
membership report for the same group. In other words, an IGMPv2 Join
MUST NOT be sent on an AC that does not lead to a CE multicast
router. This message suppression is a requirement for IGMPv2 hosts.
This is not a problem for hosts running IGMPv3 because there is no
suppression of IGMP Membership reports.
2.1.1 IGMP Leave Group Advertisement in BGP
When a PE wants to withdraw an EVPN SMET route corresponding to an
IGMPv2 Leave Group (Leave) or IGMPv3 "Leave" equivalent message, it
follows the following rules:
1) When a PE receives an IGMPv2 Leave Group or its "Leave" equivalent
message for IGMPv3 from its attached host, it checks to see if this
host is the last host who is interested in this multicast group by
sending a query for the multicast group. If the host was indeed the
last one, then the PE re-advertises EVPN SMET Multicast route with
the corresponding version flag reset. If this is the last version
flag to be reset, then instead of re-advertising the EVPN route with
all version flags reset, the PE withdraws the EVPN route for that
(*,G).
2) When a PE receives an EVPN SMET route for a given (*,G), it
Sajassi et al. Expires December 12, 2019 [Page 8]
INTERNET DRAFT IGMP Reports Aggregation in EVPN June 10, 2019
compares the received version flags from the route with its per-PE
stored version flags. If the PE finds that a version flag associated
with the (*,G) for the remote PE is reset, then the PE generates IGMP
Leave for that (*,G) toward its local interface (if any) attached to
the multicast router for that multicast group. It should be noted
that the received EVPN route should at least have one version flag
set. If all version flags are reset, it is an error because the PE
should have received an EVPN route withdraw for the last version
flag. If the PE receives an EVPN SMET route withdraw, then it must
remove the remote PE from the OIF list associated with that multicast
group.
3) When a PE receives an EVPN SMET route withdraw, it removes the
remote PE from its OIF list for that multicast group and if there are
no more OIF entries for that multicast group (either locally or
remotely), then the PE MUST stop responding to queries from the
locally attached router (if any). If there is a source for that
multicast group, the PE stops sending multicast traffic for that
source.
2.2 Proxy Querier
As mentioned in the previous sections, each PE need to have proxy
querier functionality for the following reasons:
1) To enable the collection of EVPN PEs providing L2VPN service to
act as distributed multicast router with Anycast IP address for all
attached hosts/VMs in that subnet.
2) To enable suppression of IGMP membership reports and queries over
MPLS/IP core.
3 Operation
Consider the EVPN network of figure-1, where there is an EVPN
instance configured across the PEs shown in this figure (namely PE1,
PE2, and PE3). Lets consider that this EVPN instance consist of a
single bridge domain (single subnet) with all the hosts, sources and
the multicast router shown in this figure connected to this subnet.
PE1 only has hosts connected to it. PE2 has a mix of hosts and
multicast source. PE3 has a mix of hosts, multicast source, and
multicast router. Further more, lets consider that for (S1,G1), R1 is
used as the multicast router. The following subsections describe the
IGMP proxy operation in different PEs with regard to whether the
locally attached devices for that subnet are:
- only hosts/VMs
Sajassi et al. Expires December 12, 2019 [Page 9]
INTERNET DRAFT IGMP Reports Aggregation in EVPN June 10, 2019
- mix of hosts/VMs and multicast source
- mix of hosts/VMs, multicast source, and multicast router
+--------------+
| |
| |
+----+ | | +----+
H1:(*,G1)v2 ---| | | | | |---- H6(*,G1)v2
H2:(*,G1)v2 ---| PE1| | IP/MPLS | | PE2|---- H7(S2,G2)v3
H3:(*,G1)v3 ---| | | Network | | |---- S2
H4:(S2,G2)v3 --| | | | | |
+----+ | | +----+
| |
+----+ | |
H5:(S1,G1)v3 --| | | |
S1 ---| PE3| | |
R1 ---| | | |
+----+ | |
| |
+--------------+
Figure 1:
3.1 PE with only attached hosts/VMs for a given subnet
When PE1 receives an IGMPv2 Join Report from H1, it does not forward
this join to any of its other ports (for this subnet) because all
these local ports are associated with the hosts/VMs. PE1 sends an
EVPN Multicast Group route corresponding to this join for (*,G1) and
setting v2 flag. This EVPN route is received by PE2 and PE3 that are
the member of the same BD (i.e., same EVI in case of VLAN-based
service or <EVI,VLAN> in case of VLAN-aware bundle service). PE3
reconstructs IGMPv2 Join Report from this EVPN BGP route and only
sends it to the port(s) with multicast routers attached to it (for
that subnet). In this example, PE3 sends the reconstructed IGMPv2
Join Report for (*,G1) to only R1. Furthermore, PE2 although receives
the EVPN BGP route, it does not send it to any of its port for that
subnet - namely ports associated with H6 and H7.
When PE1 receives the second IGMPv2 Join from H2 for the same
multicast group (*,G1), it only adds that port to its OIF list but it
doesn't send any EVPN BGP route because there is no change in
information. However, when it receives the IGMPv3 Join from H3 for
Sajassi et al. Expires December 12, 2019 [Page 10]
INTERNET DRAFT IGMP Reports Aggregation in EVPN June 10, 2019
the same (*,G1), besides adding the corresponding port to its OIF
list, it re-advertises the previously sent EVPN SMET route with the
version-3 & exclude flag set.
Finally when PE1 receives the IMGMPv3 Join from H4 for (S2,G2), it
advertises a new EVPN SMET route corresponding to it.
3.2 PE with mixed of attached hosts/VMs and multicast source
The main difference in here is that when PE2 receives IGMPv3 Join
from H7 for (S2,G2), it does advertises it in BGP to support source
move even though PE2 knows that S2 is attached to its local AC. PE2
adds the port associated with H7 to its OIF list for (S2,G2). The
processing for IGMPv2 received from H6 is the same as the v2 Join
described in previous section.
3.3 PE with mixed of attached hosts/VMs, multicast source and router
The main difference in here relative to the previous two sections is
that Join messages received locally needs to be sent to the port
associated with router R1. Furthermore, the Joins received via BGP
need to be passed to the R1 port but filtered for all other ports.
4 All-Active Multi-Homing
Because a CE's LAG flow hashing algorithm is unknown, in an All-
Active redundancy mode it must be assumed that the CE can send a
given IGMP message to any one of the multi-homed PEs, either DF or
non-DF - i.e., different IGMP Join messages can arrive at different
PEs in the redundancy group and furthermore their corresponding Leave
messages can arrive at PEs that are different from the ones received
the Join messages. Therefore, all PEs attached to a given ES must
coordinate IGMP Join and Leave Group (x, G) state, where x may be
either '*' or a particular source S, for each BD on that ES. This
allows the DF for that [ES, BD] to correctly advertise or withdraw a
Selective Multicast Ethernet Tag (SMET) route for that (x, G) group
in that BD when needed.
All-Active multihoming PEs for a given ES MUST support IGMP synch
procedures described in this section if they want to perform IGMP
proxy for hosts connects to that ES.
4.1 Local IGMP Join Synchronization
When a PE, either DF or non-DF, receives, on a given multihomed ES
operating in All-Active redundancy mode, an IGMP Membership Report
Sajassi et al. Expires December 12, 2019 [Page 11]
INTERNET DRAFT IGMP Reports Aggregation in EVPN June 10, 2019
for (x, G), it determines the BD to which the IGMP Membership Report
belongs. If the PE doesn't already have local IGMP Join (x, G) state
for that BD on that ES, it instantiates local IGMP Join (x, G) state
and advertises a BGP IGMP Join Synch route for that [ES, BD]. Local
IGMP Join (x, G) state refers to IGMP Join (x, G) state that is
created as the result of processing an IGMP Membership Report for (x,
G).
The IGMP Join Synch route carries the ES-Import RT for the ES on
which the IGMP Membership Report was received. Thus it may only go
to the PEs attached to that ES (and not any other PEs).
When a PE, either DF or non-DF, receives an IGMP Join Synch route it
installs that route and if it doesn't already have IGMP Join (x, G)
state for that [ES, BD], it instantiates that IGMP Join (x,G) state -
i.e., IGMP Join (x, G) state is the union of local IGMP Join (x, G)
state and installed IGMP Join Synch route. If the DF is not currently
advertising (originating) a SMET route for that (x, G) group in that
BD, it does so now.
When a PE, either DF or non-DF, deletes its local IGMP Join (x, G)
state for that [ES, BD], it withdraws its BGP IGMP Join Synch route
for that [ES, BD].
When a PE, either DF or non-DF, receives the withdrawal of an IGMP
Join Synch route from another PE it removes that route. When a PE
has no local IGMP Join (x, G) state and it has no installed IGMP Join
Synch routes, it removes IGMP Join (x, G) state for that [ES, BD].
If the DF no longer has IGMP Join (x, G) state for that BD on any ES
for which it is DF, it withdraws its SMET route for that (x, G) group
in that BD.
I.e., A PE advertises an SMET route for that (x, G) group in that BD
when it has IGMP Join (x, G) state in that BD on at least one ES for
which it is DF and it withdraws that SMET route when it does not have
IGMP Join (x, G) state in that BD on any ES for which it is DF.
4.2 Local IGMP Leave Group Synchronization
When a PE, either DF or non-DF, receives, on a given multihomed ES
operating in All-Active redundancy mode, an IGMP Leave Group message
for (x, G) from the attached CE, it determines the BD to which the
IGMPv2 Leave Group belongs. Regardless of whether it has IGMP Join
(x, G) state for that [ES, BD], it initiates the (x, G) leave group
synchronization procedure, which consists of the following steps:
1) It computes the Maximum Response Time, which is the duration of
(x, G) leave group synchronization procedure. This is the product of
Sajassi et al. Expires December 12, 2019 [Page 12]
INTERNET DRAFT IGMP Reports Aggregation in EVPN June 10, 2019
two locally configured values, Last Member Query Count and Last
Member Query Interval (described in Section 3 of [RFC2236]), plus
delta, the time it takes for a BGP advertisement to propagate between
the PEs attached to the multihomed ES (delta is a consistently
configured value on all PEs attached to the multihomed ES).
2) It starts the Maximum Response Time timer. Note that the receipt
of subsequent IGMP Leave Group messages or BGP Leave Synch routes for
(x, G) do not change the value of a currently running Maximum
Response Time timer and are ignored by the PE.
3) It initiates the Last Member Query procedure described in Section
3 of [RFC2236]; viz, it sends a number of Group-Specific Query (x, G)
messages (Last Member Query Count) at a fixed interval (Last Member
Query Interval) to the attached CE.
4) It advertises an IGMP Leave Synch route for that that [ES, BD].
This route notifies the other multihomed PEs attached to the given
multihomed ES that it has initiated an (x, G) leave group
synchronization procedure; i.e., it carries the ES-Import RT for the
ES on which the IGMP Leave Group was received. It also contains the
Maximum Response Time and the Leave Group Synchronization Procedure
Sequence number. The latter identifies the specific (x, G) leave
group synchronization procedure initiated by the advertising PE,
which increments the value whenever it initiates a procedure.
5) When the Maximum Response Timer expires, the PE that has
advertised the IGMP Leave Synch route withdraws it.
4.2.1 Remote Leave Group Synchronization
When a PE, either DF or non-DF, receives an IGMP Leave Synch route it
installs that route and it starts a timer for (x, G) on the specified
[ES, BD] whose value is set to the Maximum Response Time in the
received IGMP Leave Synch route. Note that the receipt of subsequent
IGMPv2 Leave Group messages or BGP Leave Synch routes for (x, G) do
not change the value of a currently running Maximum Response Time
timer and are ignored by the PE.
4.2.2 Common Leave Group Synchronization
If a PE attached to the multihomed ES receives an IGMP Membership
Report for (x, G) before the Maximum Response Time timer expires, it
advertises a BGP IGMP Join Synch route for that [ES, BD]. If it
doesn't already have local IGMP Join (x, G) state for that [ES, BD],
it instantiates local IGMP Join (x, G) state. If the DF is not
currently advertising (originating) a SMET route for that (x, G)
Sajassi et al. Expires December 12, 2019 [Page 13]
INTERNET DRAFT IGMP Reports Aggregation in EVPN June 10, 2019
group in that BD, it does so now.
If a PE attached to the multihomed ES receives an IGMP Join Synch
route for (x, G) before the Maximum Response Time timer expires, it
installs that route and if it doesn't already have IGMP Join (x, G)
state for that BD on that ES, it instantiates that IGMP Join (x,G)
state. If the DF is not currently advertising (originating) a SMET
route for that (x, G) group in that BD, it does so now.
When the Maximum Response Timer expires a PE that has advertised an
IGMP Leave Synch route, withdraws it. Any PE attached to the
multihomed ES, that started the Maximum Response Time and has no
local IGMP Join (x, G) state and no installed IGMP Join Synch routes,
it removes IGMP Join (x, G) state for that [ES, BD]. If the DF no
longer has IGMP Join (x, G) state for that BD on any ES for which it
is DF, it withdraws its SMET route for that (x, G) group in that BD.
4.3 Mass Withdraw of Multicast join Sync route in case of failure
A PE which has received IGMP join, would have synced IGMP join by
procedure section(4.1). If PE with local join state goes down or PE
to CE link goes down, it would lead to mass withdraw of multicast
routes. Remote PE (PE where these routes were remote IGMP join)
SHOULD not remove the state immediately where as General Query SHOULD
be generated to refresh the states. Some of the way (But not limited
to) to detect failure at peer could be IGP next hop tracking or ES
route withdraw.
5 Single-Active Multi-Homing
Note that to facilitate state synchronization after failover, the PEs
attached to a mutihomed ES operating in Single-Active redundancy mode
should also coordinate IGMP Join (x, G) state. In this case all IGMP
Join messages are received by the DF and distributed to the non-DF
PEs using the procedures described above.
6 Selective Multicast Procedures for IR tunnels
If an ingress PE uses ingress replication, then for a given (x, G)
group in a given BD:
1) It sends (x, G) traffic to the set of PEs not supporting IGMP
Proxy. This set consists of any PE that has advertised an Inclusive
Multicast Tag route for the BD without the "IGMP Proxy Support" flag.
2) It sends (x, G) traffic to the set of PEs supporting IGMP Proxy
Sajassi et al. Expires December 12, 2019 [Page 14]
INTERNET DRAFT IGMP Reports Aggregation in EVPN June 10, 2019
and having listeners for that (x, G) group in that BD. This set
consists of any PE that has advertised an Inclusive Multicast Tag
route for the BD with the "IGMP Proxy Support" flag and that has
advertised an SMET route for that (x, G) group in that BD.
If an ingress PE's Selective P-Tunnel for a given BD uses P2MP and
all of the PEs in the BD support that tunnel type and IGMP, then for
a given (x, G) group in a given BD it sends (x, G) traffic using the
Selective P-Tunnel for that (x, G) group in that BD. This tunnel
will include those PEs that have advertised an SMET route for that
(x, G) group on that BD (for Selective P-tunnel) but it may include
other PEs as well (for Aggregate Selective P-tunnel).
7 BGP Encoding
This document defines three new BGP EVPN routes to carry IGMP
membership reports. This route type is known as:
+ 6 - Selective Multicast Ethernet Tag Route
+ 7 - Multicast Join Synch Route
+ 8 - Multicast Leave Synch Route
The detailed encoding and procedures for this route type is described
in subsequent section.
7.1 Selective Multicast Ethernet Tag Route
An Selective Multicast Ethernet Tag route type specific EVPN NLRI
consists of the following:
Sajassi et al. Expires December 12, 2019 [Page 15]
INTERNET DRAFT IGMP Reports Aggregation in EVPN June 10, 2019
+---------------------------------------+
| RD (8 octets) |
+---------------------------------------+
| Ethernet Tag ID (4 octets) |
+---------------------------------------+
| Multicast Source Length (1 octet) |
+---------------------------------------+
| Multicast Source Address (variable) |
+---------------------------------------+
| Multicast Group Length (1 octet) |
+---------------------------------------+
| Multicast Group Address (Variable) |
+---------------------------------------+
| Originator Router Length (1 octet) |
+---------------------------------------+
| Originator Router Address (variable) |
+---------------------------------------+
| Flags (1 octets) (optional) |
+---------------------------------------+
For the purpose of BGP route key processing, all the fields are
considered to be part of the prefix in the NLRI except for the one-
octet optional flag field (if included). The Flags fields are defined
as follows:
0 1 2 3 4 5 6 7
+--+--+--+--+--+--+--+--+
| reserved |IE|v3|v2|v1|
+--+--+--+--+--+--+--+--+
The least significant bit, bit 7 indicates support for IGMP version
1.
The second least significant bit, bit 6 indicates support for IGMP
version 2.
The third least significant bit, bit 5 indicates support for IGMP
version 3.
The forth least significant bit, bit 4 indicates whether the (S, G)
information carried within the route-type is of Include Group type
(bit value 0) or an Exclude Group type (bit value 1). The Exclude
Group type bit MUST be ignored if bit 5 is not set.
This EVPN route type is used to carry tenant IGMP multicast group
information. The flag field assists in distributing IGMP membership
interest of a given host/VM for a given multicast route. The version
Sajassi et al. Expires December 12, 2019 [Page 16]
INTERNET DRAFT IGMP Reports Aggregation in EVPN June 10, 2019
bits help associate IGMP version of receivers participating within
the EVPN domain.
The include/exclude bit helps in creating filters for a given
multicast route.
If route is being prepared for IPv6 (MLD) then bit 7 indicates
support for MLD version 1. The second least significant bit, bit 6
indicates support for MLD version 2. Since there is no MLD version 3,
in case of IPv6 route third least significant bit MUST be 0. In case
of IPv6 route, the fourth least significant bit MUST be ignored if
bit 6 is not set.
7.1.1 Constructing the Selective Multicast Ethernet Tag route
This section describes the procedures used to construct the Selective
Multicast Ethernet Tag (SMET) route. Support for this route type is
optional.
The Route Distinguisher (RD) SHOULD be a Type 1 RD [RFC4364]. The
value field comprises an IP address of the PE (typically, the
loopback address) followed by a number unique to the PE.
The Ethernet Tag ID MUST be set as follows:
EVI is VLAN-Based or VLAN Bundle service - set to 0
EVI is VLAN-Aware Bundle service without translation - set to
the customer VID for that BD
EVI is VLAN-Aware Bundle service with translation - set to the
normalized Ethernet Tag ID - e.g., normalized VID
The Multicast Source length MUST be set to length of Multicast Source
address in bits. If the Multicast Source field contains an IPv4
address, then the value of the Multicast Source Length field is 32.
If the Multicast Source field contains an IPv6 address, then the
value of the Multicast Source Length field is 128. In case of a (*,
G) Join, the Multicast Source Length is set to 0.
The Multicast Source is the Source IP address of the IGMP membership
report. In case of a (*, G) Join, this field does not exist.
The Multicast Group length MUST be set to length of multicast group
address in bits. If the Multicast Group field contains an IPv4
address, then the value of the Multicast Group Length field is 32.
If the Multicast Group field contains an IPv6 address, then the value
of the Multicast Group Length field is 128.
Sajassi et al. Expires December 12, 2019 [Page 17]
INTERNET DRAFT IGMP Reports Aggregation in EVPN June 10, 2019
The Multicast Group is the Group address of the IGMP membership
report.
The Originator Router Length is the length of the Originator Router
address in bits.
The Originator Router Address is the IP address of Router Originating
the prefix. It should be noted that using the "Originating Router's
IP address" field is needed for local-bias procedures and may be
needed for building inter-AS multicast underlay tunnels where BGP
next hop can get over written.
The Flags field indicates the version of IGMP protocol from which the
membership report was received. It also indicates whether the
multicast group had INCLUDE or EXCLUDE bit set.
IGMP protocol is used to receive group membership information from
hosts/VMs by TORs. Upon receiving the hosts/VMs expression of
interest of a particular group membership, this information is then
forwarded using Ethernet Multicast Source Group Route NLRI. The NLRI
also keeps track of receiver's IGMP protocol version and any "source
filtering" for a given group membership. All EVPN SMET routes are
announced with per-EVI Route Target extended communities.
7.1.2 Default Selective Multicast Route
If there is multicast router connected behind EVPN domain, PE MAY
originate default SMET (*,*) to get all multicast traffic in domain.
For example,
Sajassi et al. Expires December 12, 2019 [Page 18]
INTERNET DRAFT IGMP Reports Aggregation in EVPN June 10, 2019
+--------------+
| |
| |
| | +----+
| | | |---- H1(*,G1)v2
| IP/MPLS | | PE1|---- H2(S2,G2)v3
| Network | | |---- S2
| | | |
| | +----+
| |
+----+ | |
+----+ | | | |
| | S1 ---| PE2| | |
|PIM |----R1 ---| | | |
|ASM | +----+ | |
| | | |
+----+ +--------------+
Figure 2:
Consider the EVPN network of figure-2, where there is an EVPN
instance configured across the PEs shows in this figure. Lets
consider PE2 is connected to multicast router R1 and there is PIM ASM
network behind R1. If there are receivers behind PIM ASM network, PIM
join would be forwarded to PIM RP (Rendezvous Point). If receivers
behind PIM ASM network are interested in multicast flow originated by
multicast source S2 (Behind PE1), it is necessary for PE2 to receive
multicast traffic. In this case PE2 MUST originate (*,*) SMET route
to receive all of the multicast traffic in EVPN domain.
7.2 Multicast Join Synch Route
This EVPN route type is used to coordinate IGMP Join (x,G) state for
a given BD between the PEs attached to a given ES operating in All-
Active (or Single-Active) redundancy mode and it consists of
following:
Sajassi et al. Expires December 12, 2019 [Page 19]
INTERNET DRAFT IGMP Reports Aggregation in EVPN June 10, 2019
+--------------------------------------------------+
| RD (8 octets) |
+--------------------------------------------------+
| Ethernet Segment Identifier (10 octets) |
+--------------------------------------------------+
| Ethernet Tag ID (4 octets) |
+--------------------------------------------------+
| Multicast Source Length (1 octet) |
+--------------------------------------------------+
| Multicast Source Address (variable) |
+--------------------------------------------------+
| Multicast Group Length (1 octet) |
+--------------------------------------------------+
| Multicast Group Address (Variable) |
+--------------------------------------------------+
| Originator Router Length (1 octet) |
+--------------------------------------------------+
| Originator Router Address (variable) |
+--------------------------------------------------+
| Flags (1 octet) |
+--------------------------------------------------+
For the purpose of BGP route key processing, all the fields are
considered to be part of the prefix in the NLRI except for the one-
octet Flags field, whose fields are defined as follows:
0 1 2 3 4 5 6 7
+--+--+--+--+--+--+--+--+
| reserved |IE|v3|v2|v1|
+--+--+--+--+--+--+--+--+
The least significant bit, bit 7 indicates support for IGMP version
1. The second least significant bit, bit 6 indicates support for
IGMP version 2. The third least significant bit, bit 5 indicates
support for IGMP version 3. The fourth least significant bit, bit 4
indicates whether the (S, G) information carried within the route-
type is of Include Group type (bit value 0) or an Exclude Group type
(bit value 1). The Exclude Group type bit MUST be ignored if bit 5 is
not set.
The Flags field assists in distributing IGMP membership interest of a
given host/VM for a given multicast route. The version bits help
associate IGMP version of receivers participating within the EVPN
domain. The include/exclude bit helps in creating filters for a
Sajassi et al. Expires December 12, 2019 [Page 20]
INTERNET DRAFT IGMP Reports Aggregation in EVPN June 10, 2019
given multicast route.
If route is being prepared for IPv6 (MLD) then bit 7 indicates
support for MLD version 1. The second least significant bit, bit 6
indicates support for MLD version 2. Since there is no MLD version 3,
in case of IPv6 route third least significant bit MUST be 0. In case
of IPv6 route, the fourth least significant bit MUST be ignored if
bit 6 is not set.
7.2.1 Constructing the Multicast Join Synch Route
This section describes the procedures used to construct the IGMP Join
Synch route. Support for this route type is optional. If a PE does
not support this route, then it MUST not indicate that it supports
'IGMP proxy' in Multicast Flag extended community for the EVIs
corresponding to its multi-homed Ethernet Segments.
An IGMP Join Synch route MUST carry exactly one ES-Import Route
Target extended community, the one that corresponds to the ES on
which the IGMP Join was received. It MUST also carry exactly one
EVI-RT EC, the one that corresponds to the EVI on which the IGMP Join
was received. See Section 7.5 for details on how to form the EVI-RT
EC.
The Route Distinguisher (RD) SHOULD be a Type 1 RD [RFC4364]. The
value field comprises an IP address of the PE (typically, the
loopback address) followed by a number unique to the PE.
The Ethernet Segment Identifier (ESI) MUST be set to the 10-octet
value defined for the ES.
The Ethernet Tag ID MUST be set as follows:
EVI is VLAN-Based or VLAN Bundle service - set to 0
EVI is VLAN-Aware Bundle service without translation - set to
the customer VID for the BD
EVI is VLAN-Aware Bundle service with translation - set to the
normalized Ethernet Tag ID - e.g., normalized VID
The Multicast Source length MUST be set to length of Multicast Source
address in bits. If the Multicast Source field contains an IPv4
address, then the value of the Multicast Source Length field is 32.
If the Multicast Source field contains an IPv6 address, then the
value of the Multicast Source Length field is 128. In case of a (*,
G) Join, the Multicast Source Length is set to 0.
The Multicast Source is the Source IP address of the IGMP membership
Sajassi et al. Expires December 12, 2019 [Page 21]
INTERNET DRAFT IGMP Reports Aggregation in EVPN June 10, 2019
report. In case of a (*, G) Join, this field does not exist.
The Multicast Group length MUST be set to length of multicast group
address in bits. If the Multicast Group field contains an IPv4
address, then the value of the Multicast Group Length field is 32.
If the Multicast Group field contains an IPv6 address, then the value
of the Multicast Group Length field is 128.
The Multicast Group is the Group address of the IGMP membership
report.
The Originator Router Length is the length of the Originator Router
address in bits.
The Originator Router Address is the IP address of Router Originating
the prefix.
The Flags field indicates the version of IGMP protocol from which the
membership report was received. It also indicates whether the
multicast group had INCLUDE or EXCLUDE bit set.
7.3 Multicast Leave Synch Route
This EVPN route type is used to coordinate IGMP Leave Group (x,G)
state for a given BD between the PEs attached to a given ES operating
in All-Active (or Single-Active) redundancy mode and it consists of
following:
Sajassi et al. Expires December 12, 2019 [Page 22]
INTERNET DRAFT IGMP Reports Aggregation in EVPN June 10, 2019
+--------------------------------------------------+
| RD (8 octets) |
+--------------------------------------------------+
| Ethernet Segment Identifier (10 octets) |
+--------------------------------------------------+
| Ethernet Tag ID (4 octets) |
+--------------------------------------------------+
| Multicast Source Length (1 octet) |
+--------------------------------------------------+
| Multicast Source Address (variable) |
+--------------------------------------------------+
| Multicast Group Length (1 octet) |
+--------------------------------------------------+
| Multicast Group Address (Variable) |
+--------------------------------------------------+
| Originator Router Length (1 octet) |
+--------------------------------------------------+
| Originator Router Address (variable) |
+--------------------------------------------------+
| Leave Group Synchronization # (4 octets) |
+--------------------------------------------------+
| Maximum Response Time (1 octet) |
+--------------------------------------------------+
| Flags (1 octet) |
+--------------------------------------------------+
For the purpose of BGP route key processing, all the fields are
considered to be part of the prefix in the NLRI except for the
Maximum Response Time and the one-octet Flags field, whose fields are
defined as follows:
0 1 2 3 4 5 6 7
+--+--+--+--+--+--+--+--+
| reserved |IE|v3|v2|v1|
+--+--+--+--+--+--+--+--+
The least significant bit, bit 7 indicates support for IGMP version
1. The second least significant bit, bit 6 indicates support for
IGMP version 2. The third least significant bit, bit 5 indicates
support for IGMP version 3. The fourth least significant bit, bit 4
indicates whether the (S, G) information carried within the route-
type is of Include Group type (bit value 0) or an Exclude Group type
(bit value 1). The Exclude Group type bit MUST be ignored if bit 5 is
not set.
Sajassi et al. Expires December 12, 2019 [Page 23]
INTERNET DRAFT IGMP Reports Aggregation in EVPN June 10, 2019
The Flags field assists in distributing IGMP membership interest of a
given host/VM for a given multicast route. The version bits help
associate IGMP version of receivers participating within the EVPN
domain. The include/exclude bit helps in creating filters for a
given multicast route.
If route is being prepared for IPv6 (MLD) then bit 7 indicates
support for MLD version 1. The second least significant bit, bit 6
indicates support for MLD version 2. Since there is no MLD version 3,
in case of IPv6 route third least significant bit MUST be 0. In case
of IPv6 route, the fourth least significant bit MUST be ignored if
bit 6 is not set.
7.3.1 Constructing the Multicas Leave Synch Route
This section describes the procedures used to construct the IGMP
Leave Synch route. Support for this route type is optional. If a PE
does not support this route, then it MUST not indicate that it
supports 'IGMP proxy' in Multicast Flag extended community for the
EVIs corresponding to its multi-homed Ethernet Segments.
An IGMP Leave Synch route MUST carry exactly one ES-Import Route
Target extended community, the one that corresponds to the ES on
which the IGMP Leave was received. It MUST also carry exactly one
EVI-RT EC, the one that corresponds to the EVI on which the IGMP
Leave was received. See Section 7.5 for details on how to form the
EVI-RT EC.
The Route Distinguisher (RD) SHOULD be a Type 1 RD [RFC4364]. The
value field comprises an IP address of the PE (typically, the
loopback address) followed by a number unique to the PE.
The Ethernet Segment Identifier (ESI) MUST be set to the 10-octet
value defined for the ES.
The Ethernet Tag ID MUST be set as follows:
EVI is VLAN-Based or VLAN Bundle service - set to 0
EVI is VLAN-Aware Bundle service without translation - set to
the customer VID for the BD
EVI is VLAN-Aware Bundle service with translation - set to the
normalized Ethernet Tag ID - e.g., normalized VID
The Multicast Source length MUST be set to length of multicast source
address in bits. If the Multicast Source field contains an IPv4
Sajassi et al. Expires December 12, 2019 [Page 24]
INTERNET DRAFT IGMP Reports Aggregation in EVPN June 10, 2019
address, then the value of the Multicast Source Length field is 32.
If the Multicast Source field contains an IPv6 address, then the
value of the Multicast Source Length field is 128. In case of a (*,
G) Join, the Multicast Source Length is set to 0.
The Multicast Source is the Source IP address of the IGMP membership
report. In case of a (*, G) Join, this field does not exist.
The Multicast Group length MUST be set to length of multicast group
address in bits. If the Multicast Group field contains an IPv4
address, then the value of the Multicast Group Length field is 32.
If the Multicast Group field contains an IPv6 address, then the value
of the Multicast Group Length field is 128.
The Multicast Group is the Group address of the IGMP membership
report.
The Originator Router Length is the length of the Originator Router
address in bits.
The Originator Router Address is the IP address of Router Originating
the prefix.
The Flags field indicates the version of IGMP protocol from which the
membership report was received. It also indicates whether the
multicast group had INCLUDE or EXCLUDE bit set.
7.4 Multicast Flags Extended Community
The 'Multicast Flags' extended community is a new EVPN extended
community. EVPN extended communities are transitive extended
communities with a Type field value of 6. IANA will assign a Sub-
Type from the 'EVPN Extended Community Sub-Types' registry.
A PE that supports IGMP proxy on a given BD MUST attach this extended
community to the Inclusive Multicast Ethernet Tag (IMET) route it
advertises for that BD and it Must set the IGMP Proxy Support flag to
1. Note that an [RFC7432] compliant PE will not advertise this
extended community so its absence indicates that the advertising PE
does not support IGMP Proxy.
The advertisement of this extended community enables more efficient
multicast tunnel setup from the source PE specially for ingress
replication - i.e., if an egress PE supports IGMP proxy but doesn't
have any interest in a given (x, G), it advertises its IGMP proxy
capability using this extended community but it does not advertise
Sajassi et al. Expires December 12, 2019 [Page 25]
INTERNET DRAFT IGMP Reports Aggregation in EVPN June 10, 2019
any SMET route for that (x, G). When the source PE (ingress PE)
receives such advertisements from the egress PE, it does not
replicate the multicast traffic to that egress PE; however, it does
replicate the multicast traffic to the egress PEs that don't
advertise such capability even if they don't have any interests in
that (x, G).
A Multicast Flags extended community is encoded as an 8-octet value,
as follows:
1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type=0x06 | Sub-Type=TBD | Flags (2 Octets) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Reserved=0 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
The low-order bit of the Flags is defined as the "IGMP Proxy Support"
bit. A value of 1 means that the PE supports IGMP Proxy as defined
in this document, and a value of 0 means that the PE does not support
IGMP proxy. The absence of this extended community also means that
the PE does not support IGMP proxy.
7.5 EVI-RT Extended Community
In EVPN, every EVI is associated with one or more Route Targets
(RTs). These Route Targets serve two functions:
- Distribution control: RTs control the distribution of the routes.
If a route carries the RT associated with a particular EVI, it will
be distributed to all the PEs on which that EVI exists.
- EVI Identification: Once a route has been received by a particular
PE, the RT is used to identify the EVI to which it applies.
An IGMP Join Synch or IGMP Leave Synch route is associated with a
particular combination of ES and EVI. These routes need to be
distributed only to PEs that are attached to the associated ES.
Therefore these routes carry the ES-Import RT for that ES.
Since an IGMP Join Synch or IGMP Leave Synch route does not need to
be distributed to all the PEs on which the associated EVI exists,
these routes cannot carry the RT associated with that EVI. Therefore,
when such a route arrives at a particular PE, the route's RTs cannot
Sajassi et al. Expires December 12, 2019 [Page 26]
INTERNET DRAFT IGMP Reports Aggregation in EVPN June 10, 2019
be used to identify the EVI to which the route applies. Some other
means of associating the route with an EVI must be used.
This document specifies four new Extended Communities (EC) that can
be used to identify the EVI with which a route is associated, but
which do not have any effect on the distribution of the route. These
new ECs are are known as the "Type 0 EVI-RT EC", the "Type 1 EVI-RT
EC", the "Type 2 EVI-RT EC", and the "Type 3 EVI-RT EC".
A Type 0 EVI-RT EC is an EVPN EC (type 6) of sub-type 0xA.
A Type 1 EVI-RT EC is an EVPN EC (type 6) of sub-type 0xB.
A Type 2 EVI-RT EC is an EVPN EC (type 6) of sub-type 0xC.
A Type 3 EVI-RT EC is an EVPN EC (type 6) of sub-type TBD.
Each IGMP Join Synch or IGMP Leave Synch route MUST carry exactly one
EVI-RT EC. The EVI-RT EC carried by a particular route is
constructed as follows. Each such route is the result of having
received an IGMP Join or an IGMP Leave message from a particular BD.
We will say that the route is associated with that BD. For each BD,
there is a corresponding RT that is used to ensure that routes
"about" that BD are distributed to all PEs attached to that BD. So
suppose a given IGMP Join Synch or Leave Synch route is associated
with a given BD, say BD1, and suppose that the corresponding RT for
BD1 is RT1. Then:
0. If RT1 is a Transitive Two-Octet AS-specific EC, then the EVI-RT
EC carried by the route is a Type 0 EVI-RT EC. The value field of
the Type 0 EVI-RT EC is identical to the value field of RT1.
1. If RT1 is a Transitive IPv4-Address-specific EC, then the EVI-RT
EC carried by the route is a Type 1 EVI-RT EC. The value field of
the Type 1 EVI-RT EC is identical to the value field of RT1.
2. If RT1 is a Transitive Four-Octet-specific EC, then the EVI-RT EC
carried by the route is a Type 2 EVI-RT EC. The value field of the
Type 2 EVI-RT EC is identical to the value field of RT1.
3. If RT1 is a Transitive IPv6-Address-specific EC, then the EVI-RT
EC carried by the route is a Type 3 EVI-RT EC. The value field of
the Type 3 EVI-RT EC is identical to the value field of RT1.
An IGMP Join Synch or Leave Synch route MUST carry exactly one EVI-
RT EC.
Suppose a PE receives a particular IGMP Join Synch or IGMP Leave
Sajassi et al. Expires December 12, 2019 [Page 27]
INTERNET DRAFT IGMP Reports Aggregation in EVPN June 10, 2019
Synch route, say R1, and suppose that R1 carries an ES-Import RT that
is one of the PE's Import RTs. If R1 has no EVI-RT EC, or has more
than one EVI-RT EC, the PE MUST apply the "treat-as-withdraw"
procedure of [RFC7606].
Note that an EVI-RT EC is not a Route Target Extended Community, is
not visible to the RT Constrain mechanism [RFC4684], and is not
intended to influence the propagation of routes by BGP.
1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type=0x06 | Sub-Type=n | RT associated with EVI |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| RT associated with the EVI (cont.) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Where the value of 'n' is 0x0A, 0x0B, 0x0C, or 0x0D corresponding to
EVI-RT type 0, 1, 2, or 3 respectively.
7.6 Rewriting of RT ECs and EVI-RT ECs by ASBRs
There are certain situations in which an ES is attached to a set of
PEs that are not all in the same AS, or not all operated by the same
provider. In some such situations, the RT that corresponds to a
particular EVI may be different in each AS. If a route is propagated
from AS1 to AS2, an ASBR at the AS1/AS2 border may be provisioned
with a policy that removes the RTs that are meaningful in AS1 and
replaces them with the corresponding (i.e., RTs corresponding to the
same EVIs) RTs that are meaningful in AS2. This is known as RT-
rewriting.
Note that if a given route's RTs are rewritten, and the route carries
an EVI-RT EC, the EVI-RT EC needs to be rewritten as well.
8 IGMP/MLD Immediate leave
IGMP MAY be configured with immediate leave option. This allows the
device to remove the group entry from the multicast routing table
immediately upon receiving a IGMP leave message for (x,G). In case of
all active multi-homing while synchronizing IGMP leave state to
redundancy peers, Maximum Response Time MAY be filled as Zero.
Implementation SHOULD make sure to have identical configuration
across multi home peer. In case IGMP leave Synch route is received
Sajassi et al. Expires December 12, 2019 [Page 28]
INTERNET DRAFT IGMP Reports Aggregation in EVPN June 10, 2019
with Maximum Response Time Zero, irrespective of local IGMP
configuration it MAY be processed as immediate leave.
9 IGMP Version 1 membership request
This document does not provide any detail about IGMPv1 processing.
Multicast working group are in process of absoluting uses of IGMPv1
so implementation are RECOMENDED to use IGMPv2 / MLDv1 and above
only.
10 Security Considerations
Same security considerations as [RFC7432].
11 IANA Considerations
IANA has allocated the following codepoints from the EVPN Extended
Community sub-types registry.
0x09 Multicast Flags Extended Community [this document]
0x0A EVI-RT Type 0 [this document]
0x0B EVI-RT Type 1 [this document]
0x0C EVI-RT Type 2 [this document]
IANA is requested to allocate a new codepoint from the EVPN Extended
Community sub-types registry for the following.
0x0D EVI-RT Type 3 [this document]
IANA has allocated the following EVPN route types from the EVPN Route
Type registry.
6 - Selective Multicast Ethernet Tag Route
7 - IGMP Join Synch Route
8 - IGMP Leave Synch Route
IANA is requested to create a registry, "Multicast Flags Extended
Community Flags", in the BGP registry.
The Multicast Flags Extended Community contains a 16-bit Flags field.
The bits are numbered 0-15, from low-order to high-order.
The registry should be initialized as follows:
0 : IGMP Proxy Support [this document]
1-15 : unassigned
The registration policy should be "Standards Action".
Sajassi et al. Expires December 12, 2019 [Page 29]
INTERNET DRAFT IGMP Reports Aggregation in EVPN June 10, 2019
12 References
12.1 Normative References
[KEYWORDS] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, DOI
10.17487/RFC2119, March 1997, <http://www.rfc-
editor.org/info/rfc2119>.
[RFC4360] S. Sangli et al, ""BGP Extended Communities Attribute",
February, 2006.
[RFC7432] Sajassi et al., "BGP MPLS Based Ethernet VPN", February,
2015.
12.2 Informative References
[RFC7387] Key, et al., ""A Framework for Ethernet Tree (E-Tree)
Service over a Multiprotocol Label Switching (MPLS) Network", October
2014.
[RFC7623] Sajassi, et al., ""Provider Backbone Bridging Combined with
Ethernet VPN (PBB-EVPN)", September 2015.
[FC4541] Christensen, M., Kimball, K., and F. Solensky,
"Considerations for IGMP and MLD snooping PEs", 2006.
[RFC3376] Cain, et. al., "Internet Group Management Protocol, Version
3", October 2002.
[RFC3810] Vida & Costa , "Multicast Listener Discovery Version 2
(MLDv2) for IPv6", June 2004
13 Acknowledgement
14 Contributors
Mankamana Mishra
Cisco systems
Email: mankamis@cisco.com
Authors' Addresses
Ali Sajassi
Sajassi et al. Expires December 12, 2019 [Page 30]
INTERNET DRAFT IGMP Reports Aggregation in EVPN June 10, 2019
Cisco
Email: sajassi@cisco.com
Samir Thoria
Cisco
Email: sthoria@cisco.com
Keyur Patel
Arrcus
Email: keyur@arrcus.com
Derek Yeung
Arrcus
Email: derek@arrcus.com
John Drake
Juniper
Email: jdrake@juniper.net
Wen Lin
Juniper
Email: wlin@juniper.net
Sajassi et al. Expires December 12, 2019 [Page 31]