IPCDN Working Group Michael Patrick <draft-ietf-ipcdn-qos-mib-04.txt> Motorola BCS Data Over Cable System Quality of Service Management Information Base (DOCSIS-QOS MIB) October 18, 2000 Status of this Memo This document is an Internet-Draft and is in full conformance with all the provisions of Section 10 of RFC2026. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its Areas, and its Working Groups. Note that other groups may also distribute working documents as Internet-Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as a "work in progress". The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. Copyright (c) The Internet Society 1998. All Rights Reserved. Abstract This document defines a basic set of managed objects for SNMP-based management of extended QOS features of Cable Modems (CMs) and Cable Modem Termination Systems (CMTSs) conforming to the Data over Cable System (DOCSIS) standard version 1.1. Expires April 2001 [Page 1]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 Table of Contents Status of this Memo............................... 1 Abstract.......................................... 1 Revision History.................................. 2 1. Introduction...................................... 3 1.1 Management Framework......................... 4 1.2 Glossary..................................... 5 2. Overview.......................................... 6 2.1 Textual Conventions.......................... 7 2.2 MIB Organization............................ 8 2.2.1 docsQosPktClassTable................. 11 2.2.2 docsQosParamSetTable................. 12 2.2.2.1 Interoperation with DOCSIS 1.1....... 13 2.2.3 docsQosServiceFlowTable.............. 14 2.2.4 docsQosServiceFlowStatsTable......... 14 2.2.5 docsQosUpstreamStatsTable............ 14 2.2.6 docsQosDynamicServiceStatsTable...... 14 2.2.7 docsQosServiceFlowLogTable........... 15 2.2.8 docsQosServiceClassTable............. 15 2.2.9 docsQosServiceClassPolicyTable....... 16 2.2.10 docsQosPHSTable...................... 16 2.2.11 docsQosCmtsMacToSrvFlowTable......... 16 3. Externally Administered Classification............ 17 4. Definitions....................................... 20 5. References........................................ 73 6. Authors' Addresses................................ 75 Revision History Expires April 2001 [Page 2]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 Rev Date Description --- -------- ----------- -04 10/18/00 - Updated descriptions of UGS applicable QOS param set objects. - Added two new docsQosPktClassBitMap bits and *renumbered* the bits. - Added docsQosServiceClassDirection -04 10/10/00 - Updated Overview to not mention restriction to SnmpV1. - Updated most docsQosParamSet objects to clarify default and "not applicable" values. - Add docsQosPktClassBitMap, docsQosParamSetBitMap - Restore docsQosParamSetServiceClassName - Add 5 objects to docsQosServiceFlowLogTable -04 10/01/00 - Move six objects from docsQosServiceFlowTable back to docsQosParamSetTable. - Add DCC statistics - Removed notApplicable(256) from docsQosParamSetSchedulingType -03 08/11/00 Reorganize docsQosParamSetTable. -02 12/08/99 Add docsQosServiceFlowStatsTable, docsQosUpstreamStatsTable, docsQosDynamicServiceStatsTable, docsQosServiceFlowLogTable -01 06/25/99 Complete rewrite based on -I01 draft -00 08/07/98 Initial draft posted for discussion. 1. Introduction This memo specifies a MIB module in a manner that is compliant to the SNMP SMIv2[5][6][7]. The set of objects is consistent with the SNMP framework and existing SNMP standards. This memo is a product of the IPCDN working group within the Internet Engineering Task Force. Comments are solicited and should be addressed to the working group's mailing list at ipcdn@ietf.org and/or the author. Expires April 2001 [Page 3]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 1.1 Management Framework The SNMP Management Framework presently consists of five major components: o An overall architecture, described in RFC 2271 [1]. o Mechanisms for describing and naming objects and events for the purpose of management. The first version of this Structure of Management Information (SMI) is called SMIv1 and described in RFC 1155 [2], RFC 1212 [3] and RFC 1215 [4]. The second version, called SMIv2, is described in RFC 1902 [5], RFC 1903 [6] and RFC 1904 [7]. o Message protocols for transferring management information. The first version of the SNMP message protocol is called SNMPv1 and described in RFC 1157 [8]. A second version of the SNMP message protocol, which is not an Internet standards track protocol, is called SNMPv2c and described in RFC 1901 [9] and RFC 1906 [10]. The third version of the message protocol is called SNMPv3 and described in RFC 1906 [10], RFC 2272 [11] and RFC 2274 [12]. o Protocol operations for accessing management information. The first set of protocol operations and associated PDU formats is described in RFC 1157 [8]. A second set of protocol operations and associated PDU formats is described in RFC 1905 [13]. o A set of fundamental applications described in RFC 2273 [14] and the view-based access control mechanism described in RFC 2275 [15]. Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. Objects in the MIB are defined using the mechanisms defined in the SMI. This memo specifies a MIB module that is compliant to the SMIv2. A MIB conforming to the SMIv1 can be produced through the appropriate translations. The resulting translated MIB must be semantically equivalent, except where objects or events are omitted because no translation is possible (use of Counter64). Some machine readable information in SMIv2 will be converted into textual descriptions in SMIv1 during the translation process. However, this loss of machine readable information is not considered to change the semantics of the MIB. Expires April 2001 [Page 4]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 1.2 Glossary Active QPS Active Qos Parameter Set. The set of QOS parameters that describe the current level service provided to a Service Flow. Active SF Active Service Flow. An SF with a non-empty Active QPS. Admitted QPS Admitted Qos Parameter Set. The set of QOS parameters that describe a level of service which the Service Flow is not currently using, but which it is guaranteed to receive upon the SF's request to make the set Active. Admitted SF A Service Flow with a non-empty Admitted QPS. CATV Cable TV CM Cable Modem, a modem connecting a subscriber's LAN the CATF RF network. DOCSIS CMs operate as a MAC layer bridge between the home LAN and the RF network. CMTS Cable Modem Termination System, the "head-end" device providing connectivity between the RF network and the Internet. Downstream The direction from the head end towards the subscriber. DSA Dynamic Service Addition, a DOCSIS MAC management message requesting the dynamic creation of a new Service Flow. New SFs are created with a three- message exchange of a DSA-REQ, DSA-RSP, and DSA-ACK. DSC Dynamic Service Change, a DOCSIS MAC management message requesting a change to the attributes of a Service Flow. SFs are changed with a three-message exchange of a DSC-REQ, DSC-RSP, and DSC-ACK. DSD Dynamic Service Delete, a DOCSIS MAC management message requesting the deletion of a Service Flow. SFs are deleted with a two-message exchange of a DSD-REQ and DSD-ACK. Head-end The origination point in most cable systems of the subsriber video signals. It is generally also the location of the CMTS. Expires April 2001 [Page 5]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 PHS Payload Header Suppression, a feature of DOCSIS 1.1 in which header bytes that are common in a sequence of packets of a Service Flow are replaced by a one-byte PHSI Index (PHSI) when transmitting the packet on the RF network. Provisioned QPS A QOS Parameter Set describing an envelope of service within which a Service Flow is authorized to request admission. All existing service flows must have a non-empty Provisioned QPS, hence all SFs are considered to be "Provisioned". SCN Service Class Name -- a named set of QOS parameters. A Service Flow may or may not be associated with a single named Service Class. A Service Class has as an attribute a Qos Parameter Set that is used as the default set of values for all Service Flows belonging to the Service Class. SID Service ID. A 16-bit integer assigned by the CMTS for an Upstream Service Flow with a non-empty Active QOS Parameter Set. SF Service Flow. A unidirectional stream of packets between the CM and CMTS. SFs are characterized as upstream or downstream. The SF is the fundamental unit of service provided on a DOCSIS CATV network. SFID Service Flow ID. A 32-bit unsigned integer assigned by the CMTS to each Service Flows Upstream The direction from a subscriber CM to the head-end CMTS. 2. Overview This MIB provides a set of objects required for the management of DOCSIS 1.1 compliant Cable Modems (CM) and Cable Modem Termination Systems (CMTS). The specification is derived from the DOCSIS 1.1 Radio Frequency Interface specification [16]. Please note that the referenced DOCSIS standard only requires Cable Modems to process IPv4 customer traffic. Design choices in this MIB reflect those requirements. Future versions of the DOCSIS standard are expected to require support for IPv6 as well. The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [19]. Expires April 2001 [Page 6]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 2.1 Textual Conventions The textual convention "IfDirection" is defined to indicate the direction of a packet classifer relative to an interface. It takes the values of either inbound(1) or outbound(2). The textual convention "BitRate" corresponds to the bits per second as defined for QOS Parameter Sets in DOCSIS1.1. This definition includes all bits of the Ethernet MAC frame as transmitted on the RF network, starting with the Destination Address and ending with the Ethernet FCS. It does NOT includes bits in the DOCSIS MAC header. 2.2 MIB Organization The structure of the MIB is summarized below: docsQosMIB docsQosMIBObjects docsQosPktClassTable docsQosPktClassEntry docsQosPktClassId docsQosPktClassDirection docsQosPktClassPriority docsQosPktClassIpTosLow docsQosPktClassIpTosHigh docsQosPktClassIpTosMask docsQosPktClassIpProtocol docsQosPktClassIpSourceAddr docsQosPktClassIpSourceMask docsQosPktClassIpDestAddr docsQosPktClassIpDestMask docsQosPktClassSourcePortStart docsQosPktClassSourcePortEnd docsQosPktClassDestPortStart docsQosPktClassDestPortEnd docsQosPktClassDestMacAddr docsQosPktClassDestMacMask docsQosPktClassSourceMacAddr docsQosPktClassEnetProtocolType docsQosPktClassEnetProtocol docsQosPktClassUserPriLow docsQosPktClassUserPriHigh docsQosPktClassVlanId docsQosPktClassState docsQosPktClassPkts docsQosPktClassBitMap Expires April 2001 [Page 7]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 docsQosParamSetTable docsQosParamSetEntry docsQosParamSetServiceClassName docsQosParamSetPriority docsQosParamSetMaxTrafficRate docsQosParamSetMaxTrafficBurst docsQosParamSetMinReservedRate docsQosParamSetMinReservedPkt docsQosParamSetActiveTimeout docsQosParamSetAdmittedTimeout docsQosParamSetMaxConcatBurst docsQosParamSetSchedulingType docsQosParamSetNomPollInterval docsQosParamSetTolPollJitter docsQosParamSetUnsolicitGrantSize docsQosParamSetNomGrantInterval docsQosParamSetTolGrantJitter docsQosParamSetGrantsPerInterval docsQosParamSetTosAndMask docsQosParamSetTosOrMask docsQosParamSetMaxLatency docsQosParamSetType docsQosParamSetRequestPolicyOct docsQosParamSetBitMap docsQosServiceFlowTable docsQosServiceFlowEntry docsQosServiceFlowId docsQosServiceFlowSID docsQosServiceFlowDirection docsQosServiceFlowPrimary docsQosServiceFlowStatsTable docsQosServiceFlowStatsEntry docsQosServiceFlowPkts docsQosServiceFlowOctets docsQosServiceFlowTimeCreated docsQosServiceFlowTimeActive docsQosServiceFlowPHSUnknowns docsQosServiceFlowPolicedDropPkts docsQosServiceFlowPolicedDelayPkts docsQosUpstreamStatsTable docsQosUpstreamStatsEntry docsQosSID docsQosUpstreamFragments docsQosUpstreamFragDiscards docsQosUpstreamConcatBursts docsQosDynamicServiceStatsTable docsQosDynamicServiceStatsEntry docsQosIfDirection docsQosDSAReqs docsQosDSARsps docsQosDSAAcks Expires April 2001 [Page 8]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 docsQosDSCReqs docsQosDSCRsps docsQosDSCAcks docsQosDSDReqs docsQosDSDRsps docsQosDynamicAdds docsQosDynamicAddFails docsQosDynamicChanges docsQosDynamicChangeFails docsQosDynamicDeletes docsQosDynamicDeleteFails docsQosDCCReqs docsQosDCCRsps docsQosDCCAcks docsQosDCCs docsQosDCCFails docsQosServiceFlowLogTable docsQosServiceFlowLogEntry docsQosServiceFlowLogIndex docsQosServiceFlowLogIfIndex docsQosServiceFlowLogSFID docsQosServiceFlowLogCmMac docsQosServiceFlowLogPkts docsQosServiceFlowLogOctets docsQosServiceFlowLogTimeDeleted docsQosServiceFlowLogTimeCreated docsQosServiceFlowLogTimeActive docsQosServiceFlowLogDirection docsQosServiceFlowLogPrimary docsQosServiceFlowLogServiceClassName docsQosServiceFlowLogPolicedDropPkts docsQosServiceFlowLogPolicedDelayPkts docsQosServiceFlowLogControl docsQosServiceClassTable docsQosServiceClassEntry docsQosServiceClassName docsQosServiceClassStatus docsQosServiceClassMaxTrafficRate docsQosServiceClassMaxTrafficBurst docsQosServiceClassMinReservedRate docsQosServiceClassMinReservedPkt docsQosServiceClassMaxConcatBurst docsQosServiceClassNomPollInterval docsQosServiceClassTolPollJitter docsQosServiceClassUnsolicitGrantSize docsQosServiceClassNomGrantInterval docsQosServiceClassTolGrantJitter docsQosServiceClassGrantsPerInterval docsQosServiceClassMaxLatency docsQosServiceClassActiveTimeout docsQosServiceClassAdmittedTimeout Expires April 2001 [Page 9]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 docsQosServiceClassSchedulingType docsQosServiceClassRequestPolicy docsQosServiceClassTosAndMask docsQosServiceClassTosOrMask docsQosServiceClassDirection docsQosServiceClassPolicyTable docsQosServiceClassPolicyEntry docsQosServiceClassPolicyIndex docsQosServiceClassPolicyName docsQosServiceClassPolicyRulePriority docsQosServiceClassPolicyStatus docsQosPHSTable docsQosPHSEntry docsQosPHSField docsQosPHSMask docsQosPHSSize docsQosPHSVerify docsQosPHSIndex docsQosCMtsMacToSrvFlowTable docsQosCmtsMacToSrvFlowEntry docsQosCmtsCmMac docsQosCmtsServiceFlowId docsQosCmtsIfIndex The MIB is organized as 11 tables. Most tables are implemented in both the CM and CMTS; the docsQosUpstreamStatsTable and docsQosServiceFlowLogTable are implemented on the CMTS only. 2.2.1 docsQosPktClassTable The docsQosPktClassTable reports the Service Flow Classifiers implemented by the managed device. The table is indexed by the tuple { ifIndex, docsQosServiceFlowId, docsQosPktClassId }. The ifIndex corresponds to an CATV MAC interface. Each CATV MAC interfaces has a set of Service Flows, identified with a docsQosServiceFlowId value that is unique for that interface. Each service flow may have a number of packet classifiers that map packets to the flow. The ClassiferId for the classifier is unique only within a particular service flow. The semantics of packet classification are provided in [16]. Briefly, the DOCSIS MAC interface calls for matching packets based on values within the 802.2 (LLC), 802.3, IP, and/or UDP/TCP headers. Packets which map more than one classifier are prioritized according to their docsQosPktClassPriority value. The docsQosServiceFlowId (an index object) indicates to which service flow the packet is classified. The docsQosPktClassTable is distinct from the docsDevIpFilterTable of Expires April 2001 [Page 10]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 [21] in that docsQosPktClassTable is intended only to reflect the state of the dynamically added Service Flow Classifiers. SF Classifiers may be created only via a CM configuration file or from the Dynamic Service Addition (DSA) messages. For this reason, docsQosPktClassTable is read-only. The docsDevIpFilterTable is intended for external administration of packet classifiers. See the section "Externally Administered Classification", below. 2.2.2 docsQosParamSetTable The docsQosParamSetTable reports the values of Qos Parameter Set as defined in Section C.2.2 of [16]. In general, a Service Flow is associated with three different Qos Parameter Sets (QPSs): an "active" QPS, an "admitted" QPS, and a "provisioned" or "authorized" QPS. The relationship of these three sets is represented below: +---------------------+ | Provisioned | | | | +---------------+ | | | Admitted | | | | | | | | +---------+ | | | | | Active | | | | | | | | | | | +---------+ | | | | | | | +---------------+ | | | +---------------------+ Figure 1: Qos Parameter Sets The Provisioned QPS describes the maximum service envelope for which the SF is authorized. The Admitted QPS is the set of services for which a service flow has requested admission to the DOCSIS RF network, but which is not yet active. The Admitted QPS is used during the two-phase process of IP Telephony service flow admission to admit the bandwidth for a bidirectional voice call when the far end is Expires April 2001 [Page 11]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 ringing. Since ringing may occur for up to four minutes, this permits the bandwidth to be reserved but not actually consumed during this interval. The Active QPS is the set of services actually being used by the Service Flow. The DOCSIS v1.1 specification [16] defines what it means for a QPS envelope to be "within" another. In general, an inner QPS is considered to be "within" an outer QPS when all QOS parameters represent demands of equal or fewer resources of the network. In addition to their use as attributes of a Service Flow, a QPS is also an attribute of a Service Class. A DOCSIS CM configuration file or DSA message may request the creation of a new SF and give only the Service Class Name. The CMTS "expands the macro" of a Service Class Name creation by populating the Provisioned, Admitted, and/or Active QPSs of the Service Flow with the QPS of the Service Class Name. All of the QPSs of a Service Flow must be expansions of the same Service Class, and in this case the SF is said to "belong" to the Service Class. Changing the contents of a Service Class' QPS does not affect the QPS of any Service Flow earlier expanded from that Service Class name. Only the CMTS implements docsQosServiceClassTable. See [16] section 8 for a full description and the theory of operation of Docsis 1.1 QOS operation. The docsQosParamSetTable sets are indexed by { ifIndex, docsQosServiceFlowId, docsQosParamSetType}. ifIndex indicates a particular "DOCSIS MAC Domain". docsQosServiceFlowId uniquely identifies a service flow on that MAC domain. The docsQosParamSetType indicates whether the row describes an active, admitted, or provisioned Qos Parameter Set. The docsQosParamSetTable is read-only, because it indicates the Qos Parameter Set contents as defined by DOCSIS signalling. The docsQosServiceClassTable is read-create to permit managers to define a template of Qos Parameters that can be referenced by DOCSIS modems when creating their Qos Parameter Sets. 2.2.2.1 Interoperation_with_DOCSIS_1.0 The DOCSIS 1.0 DOCS-IF-MIB [22] specifies a docsIfQosProfileTable to describe the set of Class Of Service (COS) parameters associated with a COS "profile". The docsIfCmServiceTable, which contains one entry per SID, references this table with a docsIfCmServiceQosProfile number. The DOCSIS 1.1 CM registration process allows a modem to register as operating either with DOCSIS 1.0 or DOCSIS 1.1 functionality. For ease of expression, we call a modem registering with DOCSIS 1.0 Expires April 2001 [Page 12]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 functionality a "DOCSIS 1.0 modem", regardless of the modem's capabilities. A CMTS or CM supporting both DOCSIS 1.0 and DOCSIS 1.1 implements both the tables of [22] and the tables of this MIB. The interoperation goal is that before modem registration, the DOCSIS 1.0 MIB [22] applies. After registration, either the DOCSIS 1.0 or DOCSIS 1.1 MIB applies, depending on the mode with which the modem registered. The specific interoperation rules are: 1. When a CM initially ranges, both the CM and CMTS implement a row in DOCS-IF-MIB docsIfQosProfileTable and docsIfCmServiceTable corresponding to the default upstream Service ID (SID) used for pre-registration upstream traffic. The docsIfQosProfileTable row may be either exclusively referenced by the docsIfCmServiceTable row for the CM or, as is likely, multiply-referenced by several docsIfCmServiceTable rows. 2. Both a CMTS and CM implementing this MIB MUST NOT implement docsQosParamSetTable or docsQosServiceFlowTable rows until after the CM registers with DOCSIS 1.1 modem operation. 3. When a modem registers with the CMTS as a "DOCSIS 1.1" modem, any exclusively-referenced row in DOCS-IF-MIB docsQosProfileTable representing the modems upstream Qos profile for pre-registration traffic MUST be removed. Multiply-referenced rows may remain, of course. The docsQosIfCmServiceQosProfile object in the CM's row of docsIfCmServiceTable MUST be set to zero. The docsIfCmServiceTable row for the DOCSIS 1.1 modem continues to exist, and the various statistic objects in that row are incremented. 4. When a DOCSIS 1.1 modem registers, both the CMTS and CM represent all service flows described in the modem configuration file in docsQosParamSetTable and docsQosServiceFlowTable. Expires April 2001 [Page 13]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 2.2.3 docsQosServiceFlowTable The docsQosServiceFlowTable provides read-only information about all of the service flows known by the device. It is indexed by the combination of { ifIndex, dosQosServiceFlowId }, where ifIndex corresponds to a CATV MAC interface and docsQosServiceFlowId is the 32- bit integer assigned by the CMTS controlling the MAC domain. A CM typically has only a single CATV MAC interface, while a CMTS may have several. See [22] for a description of the ifIndex numbering for DOCSIS devices. The table indicates whether a given SF is in the upstream or downstream direction, and whether it is the "primary" SF in that direction. The primary SF carries traffic that is not otherwise classified to any other SF in that direction. 2.2.4 docsQosServiceFlowStatsTable The docsQosServiceFlowStatsTable provides statistics for all currently existing SFs known by the managed device. It provides basic packet and octet counters, as well as certain other SF-specific stats such as the time at which the flow was created and how many seconds it has been active. The table also provides objects which can be used to fine-tune admission control decisions, namely the number of packets dropped or delayed due to QOS policing decisions enforced by the managed device. 2.2.5 docsQosUpstreamStatsTable This table provides statistics that are measured only at the CMTS in the upstream direction. These include a count of the number of fragmentation headers received, fragments discarded, and the number of concatenation headers received. 2.2.6 docsQosDynamicServiceStatsTable This table provides read-only stats on the operation of the Dynamic Service state machines as specified in section 9.4 of [16]. It provides a set of 14 counters *in each direction* for a Docsis MAC layer interface. That is, each Docsis MAC layer interface has one row for downstream stats, and a second row for upstream stats. Eight of the counters are DSx packet type counts, one counter for each of the eight DSx packet types. For example, the docsQosDSAReqs object in the upstream row at the CMTS counts the number of DSA-REQ messages received by the CMTS from that interface. The docsQosDSAReqs object in the downstream row at the CMTS counts the Expires April 2001 [Page 14]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 number of DSA-REQ messages transmitted by the CMTS on that interface. The remaining six counters per (interface, direction) combination count the number of successful and unsuccessful *transactions* that were initiated on the interface and direction. For example, the upstream docsQosDynamicAdds on a CMTS is the number of successfully completed CM-initiated dynamic additions, because at the CMTS a CM- initiated DSA starts in the upstream direction. The downstream docsQosDynamicAdds at a CMTS is the number of successful CMTS- initiated DSA transactions. Dynamic service transactions can fail for a number of reasons, as listed in the state machines of section 9.4. Rather than include still more counters for each different failure reason, they are grouped into a single count, e.g docsQosDynamicAddFails. Again, this object exists in both directions, so that locally originated vs remotely originated transaction failures are counted separately. Further troubleshooting of transaction failures will require vendor- specific queries and operation. 2.2.7 docsQosServiceFlowLogTable This table contains a log of the Service Flows no longer existing in the docsQosServiceFlowTable. It is intended to be periodically polled by traffic monitoring and billing agents. It is implemented only at the CMTS. It contains a chronlogical log of SF session statistics, including a total count of packets and octets transferred on the SF. It includes time stamps of the SF creation and deletion time, as well as its number of active seconds. The active second count is the count of seconds that the SF had a non-empty Active Qos Parameter Set, i.e. it was eligible to pass data. For unicast SFs, it includes the CM MAC address associated with the flow for billing reference purposes. The maximum number of log records kept by a CMTS, and the duration that a log record is maintained in the table is vendor-specific. An explicit control object is provided so that the monitoring application can explicitly delete records it has read. 2.2.8 docsQosServiceClassTable This table defines the Service Class Name and references a Qos Parameter Set for each Service Class defined in a CMTS. It is indexed by the Service Class Name string itself. The table is read- create on a CMTS, and is not implemented in a CM. Each entry of the docsQosServiceClassTable should define a template for flows in a given direction (upstream or downstream). Some parameters of the docsQosServiceClassTable are specific to a particular direction, and Expires April 2001 [Page 15]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 so their values are not-applicable when used as a template for flows in the other direction. 2.2.9 docsQosServiceClassPolicyTable The docsQosServiceClassPolicyTable can be referenced by the docsDevFilterPolicyTable of [21] in order to have a "policy" that classifies packets to a named Service Class. This is one mechanism by which "external" entities (like an SNMP manager) may control the classification of packet for QOS purposes. Entries are indexed by a small integer docsQosServiceClassPolicyIndex. They provide a Service Class Name and a Rule Priority. A policy referencing a row of this table intends the packet to be forwarded on a Service Flow "belonging" to the named Service Class. See the section "Externally Administered Classification", below. This table is implemented on both the CM and CMTS, and is read-create on both. 2.2.10 docsQosPHSTable The Payload Header Suppression (PHS) feature of DOCSIS 1.1 permits packets to replace the unchanging bytes of the Ethernet, IP, and UDP headers with a one-byte index when transmitting on the cable network. This is especially useful for IP Telephony packets, where such suppression can result in almost twice the number of calls supported within the same upstream channel. Each entry of the table corresponds to a PHS Rule as described in section 8.4 of [16]. The rules are identified by their corresponding service flow ID and docsQosPktClassId. A PHS rule is associated with exactly one classifier. The table is therefore indexed by the tuple { ifINdex, docsQosServiceFlowId, docsQosPktClassId}. This table is read-only, and MUST be implemented on both the CM and CMTS when PHS is supported. 2.2.11 docsQosCmtsMacToSrvFlowTable The docsQosCmtsMacToSrvFlowTable provides describes the mapping of CM mac addresses to the Service Flow Ids that are uniquely identified with that CM. External applications may collect statistics on all packets flowing through a CM by determining the SFID of all of its flows, and then collecting the statistics of packets and bytes for each flow. Expires April 2001 [Page 16]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 Downstream multicast service flows are not indicated in the docsQosCmtsMacToSrvFlowTable because they are not associated with only one CM. 3. Externally Administered Classification Docsis 1.1 provides rich semantics for the classification of packets to service flows with it Service Flow Classifier table. Service Flow Classifiers may be created statically in the DOCSIS CM configuration file, or may be created dynamically with Dynamic Service Addition (DSA) and Dynamic Service Change (DSC) DOCSIS MAC messages. Several major issues arose with the concept of externally administered classification, i.e. should an external SNMP manager be permitted to create classification rows? One problem was the co- ordination of classifier IDs, since such an approach would require either separate classifier ID number spaces or objects to co-ordinate both internal and external classifier ID assignments. A more serious problem, however, was the requirement that external creation of SF Classifiers would require "knowledge" of the individual Service Flow ID for service flows by external applications. It was strongly felt by the committee that SFIDs should remain an internal Docsis object, and not be transmitted as part of protocol flows, e.g. for IP packet telephony signalling. Docsis 1.1 introduced the concept of named Service Classes for ease of administration within a domain of CMs and CMTSs. What was desired was to permit external classification of packets to a Service Class, not a particular Service Flow. The DOCSIS committee therefore decided to use the already-defined IP Packet Filter Table [21] for the external classification of packets for QOS purposes. The docsDevIpPacketFilterTable defines similar packet matching criteria as docsQosPktClassTable, but it matches a packet to an arbitrary "policy set" instead of a particular Service Flow. One of the policies in the policy set then selects the Service Class of the SF on which to forward the packet. The docsQosServiceClassPolicyTable of this MIB defines the Service Class Name to which a packet is classified. Expires April 2001 [Page 17]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 The interaction of external and internal packet classification is depicted below. | | Outbound Pkt V docsDevIpFilterTable------> docsDevFilterPolicyTable | | | V | docsQosServiceClassPolicyTable | | | Pkt | ServiceClassName, | | ServiceClassPolicyRulePriority V V +--------------------------------------------------------+ | | DOCSIS MAC LAYER ENTITY | | | | | Select any | | V | SFID Y in SCN| | docsQosPktClassTable <---------------| | | | | | | | docsQosPktClassPriority, | | | | SFID X | | | V V | | ----------------------------------------+ | | | Select the SFID associated with the | | | | higher of docsQosPktClassPriority or | | | | docsQosServiceClassPolicyRulePriority | | | +---------------------------------------+ | | | | | V | | | | | | | | | | ... | | Service Flows | | +----+ +----+ | | SFID X SFID Y | +--------------------------------------------------------+ Figure 2: Docsis Packet Classification The processing of an outgoing packet proceeds as follows: 1. The packet is first checked for matches with rows of the docsDevIpFilterTable. If it matches, the matching row provides a docsDevFilterPolicyId integer. 2. The docsDevFilterPolicyId indexes into one (or more) rows of docsDevFilterPolicyTable. Each row provides an arbitrary RowPointer (docsDevFilterPolicyPtr), Expires April 2001 [Page 18]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 corresponding to a policy to be applied to the packet. 3. This MIB defines a docsQosServiceClassPolicyTable whose entries may be pointed to by docsDevFilterPolicyPtr in order to administratively classify packets to a named DOCSIS Service Class. The docsQosServiceClassPolicyEntry provides a Service Class Name (SCN) as docsQosServiceClassPolicyName and a classification rule priority as docsQosServiceClassPolicyRulePriority. These are submitted to the device's Docsis MAC Layer entity as a special form of the MAC_DATA.request primitive, as described in Section E.2.1 of [16]. 4. The MAC Layer selects an SFID ("Y") of an active Service Flow belonging to the named class, choosing an SF arbitrarily if there is more than one. 5. The packet is then classified according to the docsQosPktClassTable, which may classify the packet to a different SFID "X". Associated with the classifier is a docsQosPktClassPriority. 6. In the event of a conflict between the SCN-determined SFID and the classified SFID, the greater of docsQosPktClassPriority and docsQosServiceClassPolicyRulePriority determines which SFID is selected to forward the packet. A packet which does not match a docsQosServiceClassPolicyEntry is directly submitted to the Docsis MAC layer, where the docsQosPktClassTable selects the SID on which it is to be forwarded. By convention (in [16]), the "internal" docsQosPktClassPriority values should be in the range of 64-191, while the "external" priorities may be either in the range 192-255 to override the internal classification or the range 0-63 to be overriden by internal classification. This classification mechanism applies both upstream from the CM and downstream from the CMTS. Expires April 2001 [Page 19]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 4. Definitions -- -- Docsis QOS Extensions MIB -- DOCS-QOS-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Integer32, Counter32, IpAddress, Unsigned32 FROM SNMPv2-SMI TEXTUAL-CONVENTION, MacAddress, RowStatus, TruthValue, DisplayString, TimeStamp FROM SNMPv2-TC OBJECT-GROUP, MODULE-COMPLIANCE FROM SNMPv2-CONF ifIndex, InterfaceIndex FROM IF-MIB docsIfMib FROM DOCS-IF-MIB; docsQosMIB MODULE-IDENTITY LAST-UPDATED "0010180000Z" -- Oct 18, 2000 ORGANIZATION "IETF IPCDN Working Group" CONTACT-INFO " Co-Author: Michael Patrick Postal: Motorola ISG 20 Cabot Blvd, MS M4-30 Mansfield, MA 02048-1193 U.S.A. Phone: +1 508 261 5707 E-mail: michael.patrick@motorola.com" DESCRIPTION "This is the management information for Expires April 2001 [Page 20]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 Quality Of Service (QOS) for DOCSIS 1.1." REVISION "0010180000Z" -- October 18, 2000 DESCRIPTION "Published as draft-ietf-ipcdn-qos-mib-04.txt. Changes from qos-mib-03 include: - Moved six objects from docsQosServiceFlowTable back to docsQosParamSetTable. - Added five counters to docsQosDynamicServiceStatsTable for DCC counts. - Removed notApplicable(256) from docsQosParamSetSchedulingType - Clarified reported values of docsQosParamSetTable objects. The CMTS reports any CMTS-specific default value it is using, and unknown or not applicable params are reported as zero. - Add docsQosPktClassBitMap - Add docsQosParamSetBitMap - Restore docsQosParamSetServiceClassName - Add 5 objects to docsQosServiceFlowLogTable - Add docsQosServiceClassDirection " ::= { docsIfMib 7 } -- BPIPlus mib is docsIfMIb 6 docsQosMIBObjects OBJECT IDENTIFIER ::= { docsQosMIB 1 } -- Textual Conventions IfDirection ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Indicates a direction on an RF MAC interface. The value downstream(1) is from Cable Modem Termination System to Cable Modem. The value upstream(2) is from Cable Modem to Cable Modem Termination System." SYNTAX INTEGER { downstream(1), upstream(2) } BitRate ::= TEXTUAL-CONVENTION DISPLAY-HINT "d" STATUS current DESCRIPTION "The rate of traffic in unit of bits per second. Used to specify traffic rate for QOS." SYNTAX Unsigned32 SchedulingType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The scheduling service provided by a CMTS for an upstream service flow. If the parameter is omitted Expires April 2001 [Page 21]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 from an upstream QOS Parameter Set, this object takes the value of bestEffort (2). This parameter must be reported as undefined (1) for downstream QOS Parameter Sets." SYNTAX INTEGER { undefined (1), bestEffort (2), nonRealTimePollingService(3), realTimePollingService(4), unsolictedGrantServiceWithAD(5), unsolictedGrantService(6) } ----------------------------------------------------------------------- -- -- Packet Classifier Table -- docsQosPktClassTable OBJECT-TYPE SYNTAX SEQUENCE OF DocsQosPktClassEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the packet classification configured on the CM or CMTS. The model is that a packet either received as input from an interface or transmitted for output on an interface may be compared against an ordered list of rules pertaining to the packet contents. Each rule is a row of this table. A matching rule provides a service flow id to to which the packet is classified. All rules need to match for a packet to match a classifier. The objects in this row correspond to a set of Classifier Encoding parameters in a DOCSIS MAC management message. The docsQosPktClassBitMap indicates which particular parameters were present in the classifier as signalled in the DOCSIS message. If the referenced parameter was not present in the signalled DOCSIS 1.1 Classifier, the corresponding object in this row reports a value as specified in the DESCRIPTION section. " ::= { docsQosMIBObjects 1 } docsQosPktClassEntry OBJECT-TYPE SYNTAX DocsQosPktClassEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table provides a single packet Expires April 2001 [Page 22]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 classifier rule. The index ifIndex is an ifType of docsCableMaclayer(127)." INDEX { ifIndex, docsQosServiceFlowId, docsQosPktClassId } ::= { docsQosPktClassTable 1 } DocsQosPktClassEntry ::= SEQUENCE { docsQosPktClassId Integer32, docsQosPktClassDirection IfDirection, docsQosPktClassPriority Integer32, docsQosPktClassIpTosLow OCTET STRING, docsQosPktClassIpTosHigh OCTET STRING, docsQosPktClassIpTosMask OCTET STRING, docsQosPktClassIpProtocol Integer32, docsQosPktClassIpSourceAddr IpAddress, docsQosPktClassIpSourceMask IpAddress, docsQosPktClassIpDestAddr IpAddress, docsQosPktClassIpDestMask IpAddress, docsQosPktClassSourcePortStart Integer32, docsQosPktClassSourcePortEnd Integer32, docsQosPktClassDestPortStart Integer32, docsQosPktClassDestPortEnd Integer32, docsQosPktClassDestMacAddr MacAddress, docsQosPktClassDestMacMask MacAddress, docsQosPktClassSourceMacAddr MacAddress, docsQosPktClassEnetProtocolType INTEGER, docsQosPktClassEnetProtocol Integer32, docsQosPktClassUserPriLow Integer32, docsQosPktClassUserPriHigh Integer32, docsQosPktClassVlanId Integer32, docsQosPktClassState INTEGER, docsQosPktClassPkts Counter32, docsQosPktClassBitMap BITS } docsQosPktClassId OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index assigned to packet classifier entry by the CMTS which is unique per service flow." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.3.2" ::= { docsQosPktClassEntry 1 } docsQosPktClassDirection OBJECT-TYPE SYNTAX IfDirection Expires April 2001 [Page 23]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the direction to which the classifier is applied." ::= { docsQosPktClassEntry 2 } docsQosPktClassPriority OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The value specifies the order of evaluation of the classifiers. The higher the value the higher the priority. The value of 0 is used as default in provisioned service flows classifiers. The default value of 64 is used for dynamic service flow classifiers. If the referenced parameter is not present in a classifier, this object reports the default value as defined above." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.3.5" ::= { docsQosPktClassEntry 3 } docsQosPktClassIpTosLow OBJECT-TYPE SYNTAX OCTET STRING (SIZE(1)) MAX-ACCESS read-only STATUS current DESCRIPTION "The low value of a range of TOS byte values. If the referenced parameter is not present in a classifier, this object reports the value of 0." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.5.1" ::= { docsQosPktClassEntry 4 } docsQosPktClassIpTosHigh OBJECT-TYPE SYNTAX OCTET STRING (SIZE(1)) MAX-ACCESS read-only STATUS current DESCRIPTION "The 8-bit high value of a range of TOS byte values. If the referenced parameter is not present in a classifier, this object reports the value of 0." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.5.1" ::= { docsQosPktClassEntry 5 } docsQosPktClassIpTosMask OBJECT-TYPE SYNTAX OCTET STRING (SIZE(1)) MAX-ACCESS read-only STATUS current DESCRIPTION "The mask value is bitwise ANDed with TOS byte in an IP packet and this value is used check Expires April 2001 [Page 24]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 range checking of TosLow and TosHigh. If the referenced parameter is not present in a classifier, this object reports the value of 0." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.5.1" ::= { docsQosPktClassEntry 6 } docsQosPktClassIpProtocol OBJECT-TYPE SYNTAX Integer32 (0..258) MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the value of the IP Protocol field required for IP packets to match this rule. The value 256 matches traffic with any IP Protocol value. The value 257 by convention matches both TCP and UDP. If the referenced parameter is not present in a classifier, this object reports the value of 258." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.5.2" ::= { docsQosPktClassEntry 7 } docsQosPktClassIpSourceAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the value of the IP Source Address required for packets to match this rule. An IP packet matches the rule when the packet ip source address bitwise ANDed with the docsQosPktClassIpSourceMask value equals the docsQosPktClassIpSourceAddr value. If the referenced parameter is not present in a classifier, this object reports the value of 0.0.0.0." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.5.3" ::= { docsQosPktClassEntry 8 } docsQosPktClassIpSourceMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies which bits of a packet's IP Source Address that are compared to match this rule. An IP packet matches the rule when the packet source address bitwise ANDed with the docsQosPktClassIpSourceMask value equals the Expires April 2001 [Page 25]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 docsQosIpPktClassSourceAddr value. If the referenced parameter is not present in a classifier, this object reports the value of 0.0.0.0." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.5.4" ::= { docsQosPktClassEntry 9 } docsQosPktClassIpDestAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the value of the IP Destination Address required for packets to match this rule. An IP packet matches the rule when the packet IP destination address bitwise ANDed with the docsQosPktClassIpDestMask value equals the docsQosPktClassIpDestAddr value. If the referenced parameter is not present in a classifier, this object reports the value of 0.0.0.0." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.5.5" ::= { docsQosPktClassEntry 10 } docsQosPktClassIpDestMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies which bits of a packet's IP Destination Address that are compared to match this rule. An IP packet matches the rule when the packet destination address bitwise ANDed with the docsQosPktClassIpDestMask value equals the docsQosPktClassIpDestAddr value. If the referenced parameter is not present in a classifier, this object reports the value of 0.0.0.0." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.5.6" ::= { docsQosPktClassEntry 11} docsQosPktClassSourcePortStart OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the low end inclusive Expires April 2001 [Page 26]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 range of TCP/UDP source port numbers to which a packet is compared. This object is irrelevant for non-TCP/UDP IP packets. If the referenced parameter is not present in a classifier, this object reports the value of 0." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.5.7" ::= { docsQosPktClassEntry 12 } docsQosPktClassSourcePortEnd OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the high end inclusive range of TCP/UDP source port numbers to which a packet is compared. This object is irrelevant for non-TCP/UDP IP packets. If the referenced parameter is not present in a classifier, this object reports the value of 65535." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.5.9" ::= { docsQosPktClassEntry 13 } docsQosPktClassDestPortStart OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the low end inclusive range of TCP/UDP destination port numbers to which a packet is compared. If the referenced parameter is not present in a classifier, this object reports the value of 0." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.5.9" ::= { docsQosPktClassEntry 14 } docsQosPktClassDestPortEnd OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the high end inclusive range of TCP/UDP destination port numbers to which a packet is compared. If the referenced parameter is not present in a classifier, this object reports the value of 65535." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.5.10" ::= { docsQosPktClassEntry 15 } Expires April 2001 [Page 27]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 docsQosPktClassDestMacAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "An Ethernet packet matches an entry when its destination MAC address bitwise ANDed with docsQosPktClassDestMacMask equals the value of docsQosPktClassDestMacAddr. If the referenced parameter is not present in a classifier, this object reports the value of '000000000000'H. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.6.1" ::= { docsQosPktClassEntry 16 } docsQosPktClassDestMacMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "An Ethernet packet matches an entry when its destination MAC address bitwise ANDed with docsQosPktClassDestMacMask equals the value of docsQosPktClassDestMacAddr. If the referenced parameter is not present in a classifier, this object reports the value of '000000000000'H. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.6.1" ::= { docsQosPktClassEntry 17 } docsQosPktClassSourceMacAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "An Ethernet packet matches this entry when its source MAC address equals the value of this object. If the referenced parameter is not present in a classifier, this object reports the value of 'FFFFFFFFFFFF'H. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.6.2" ::= { docsQosPktClassEntry 18 } docsQosPktClassEnetProtocolType OBJECT-TYPE SYNTAX INTEGER { none(0), Expires April 2001 [Page 28]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 ethertype(1), dsap(2), mac(3), all(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the format of the layer 3 protocol id in the Ethernet packet. A value of none(0) means that the rule does not use the layer 3 protocol type as a matching criteria. A value of ethertype(1) means that the rule applies only to frames which contains an EtherType value. Ethertype values are contained in packets using the Dec-Intel-Xerox (DIX) encapsulation or the RFC1042 Sub-Network Access Protocol (SNAP) encapsulation formats. A value of dsap(2) means that the rule applies only to frames using the IEEE802.3 encapsulation format with a Destination Service Access Point (DSAP) other than 0xAA (which is reserved for SNAP). A value of mac(3) means that the rule applies only to MAC management messages for MAC management messages. A value of all(4) means that the rule matches all Ethernet packets. If the Ethernet frame contains an 802.1P/Q Tag header (i.e. EtherType 0x8100), this object applies to the embedded EtherType field within the 802.1P/Q header. If the referenced parameter is not present in a classifier, this object reports the value of 0. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.6.3" ::= { docsQosPktClassEntry 19 } docsQosPktClassEnetProtocol OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "If docsQosEthPktClassProtocolType is none(0), this object is ignored when considering whether Expires April 2001 [Page 29]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 a packet matches the current rule. If dosQosPktClassEnetProtocolType is ethertype(1), this object gives the 16-bit value of the EtherType that the packet must match in order to match the rule. If docsQosPktClassEnetProtocolType is dsap(2), the lower 8 bits of this object's value must match the DSAP byte of the packet in order to match the rule. If docsQosPktClassEnetProtocolType is mac(3), the lower 8 bits of this object value represent a lower bound (inclusive) of MAC management message type codes matched, and the upper 8 bits of this object value represent the upper bound (inclusive) of matched MAC message type codes. Certain message type codes are excluded from matching, as specified in the reference. If the Ethernet frame contains an 802.1P/Q Tag header (i.e. EtherType 0x8100), this object applies to the embedded EtherType field within the 802.1P/Q header. If the referenced parameter is not present in the classifier, the value of this object is reported as 0. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.6.3" ::= { docsQosPktClassEntry 20 } -- docsQosPktClassUserPriApplies { docsQosPktClassEntry 21 } -- was removed in revision -03. docsQosPktClassUserPriLow OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS read-only STATUS current DESCRIPTION "This object applies only to Ethernet frames using the 802.1P/Q tag header (indicated with EtherType 0x8100). Such frames include a 16-bit Tag that contains a 3 bit Priority field and a 12 bit VLAN number. Tagged Ethernet packets must have a 3-bit Priority field within the range of docsQosPktClassPriLow and docsQosPktClassPriHigh in order to match this rule. If the referenced parameter is not present in the Expires April 2001 [Page 30]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 classifier, the value of this object is reported as 0. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.7.1" ::= { docsQosPktClassEntry 22 } docsQosPktClassUserPriHigh OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS read-only STATUS current DESCRIPTION "This object applies only to Ethernet frames using the 802.1P/Qtag header (indicated with EtherType 0x8100). Such frames include a 16-bit Tag that contains a 3 bit Priority field and a 12 bit VLAN number. Tagged Ethernet packets must have a 3-bit Priority field within the range of docsQosPktClassPriLow and docsQosPktClassPriHigh in order to match this rule. If the referenced parameter is not present in the classifier, the value of this object is reported as 7. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.7.1" ::= { docsQosPktClassEntry 23 } docsQosPktClassVlanId OBJECT-TYPE SYNTAX Integer32 (0..4095) MAX-ACCESS read-only STATUS current DESCRIPTION "This object applies only to Ethernet frames using the 802.1P/Q tag header. If this object's value is nonzero, tagged packets must have a VLAN Identifier that matches the value in order to match the rule. Only the least significant 12 bits of this object's value are valid. If the referenced parameter is not present in the classifier, the value of this object is reported as 0. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.7.2" ::= { docsQosPktClassEntry 24 } docsQosPktClassState OBJECT-TYPE SYNTAX INTEGER { Expires April 2001 [Page 31]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 active(1), inactive(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates whether or not the classifier is enabled to classify packets to a Service Flow. If the referenced parameter is not present in the classifier, the value of this object is reported as active(1). " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.3.6" ::= { docsQosPktClassEntry 25 } docsQosPktClassPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object counts the number of packets that have been classified using this entry." ::= { docsQosPktClassEntry 26 } docsQosPktClassBitMap OBJECT-TYPE SYNTAX BITS { -- Reference SP-RFIv1.1-I05-000714 rulePriority(0), -- Appendix C.2.1.3.4 activationState(1), -- Appendix C.2.1.3.6 ipTos(2), -- Appendix C.2.1.5.1 ipProtocol(3), -- Appendix C.2.1.5.2 ipSourceAddr(4), -- Appendix C.2.1.5.3 ipSourceMask(5), -- Appendix C.2.1.5.4 ipDestAddr(6), -- Appendix C.2.1.5.5 ipDestMask(7), -- Appendix C.2.1.5.6 sourcePortStart(8), -- Appendix C.2.1.5.7 sourcePortEnd(9), -- Appendix C.2.1.5.8 destPortStart(10), -- Appendix C.2.1.5.9 destPortEnd(11), -- Appendix C.2.1.5.10 destMac(12), -- Appendix C.2.1.6.1 sourceMac(13), -- Appendix C.2.1.6.2 ethertype(14), -- Appendix C.2.1.6.3 userPri(15), -- Appendix C.2.1.7.1 vlanId(16) -- Appendix C.2.1.7.2 } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates which parameter encodings were actually present in the DOCSIS packet classifier encoding signalled in the DOCSIS message that created the classifier. A bit of of this object is set to 1 if the parameter Expires April 2001 [Page 32]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 indicated by the comment was present in the classifier encoding, and 0 otherwise. Note that BITS are encoded most significant bit first, so that if e.g. bits 6 and 7 are set, this object is encoded as the octet string '030000'H. " ::= { docsQosPktClassEntry 27 } -- -- QOS Parameter Set Table -- docsQosParamSetTable OBJECT-TYPE SYNTAX SEQUENCE OF DocsQosParamSetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the set of DOCSIS 1.1 QOS parameters defined in a managed device. The ifIndex index specifies a DOCSIS MAC Domain. The docsQosServiceFlowId index specifies a particular Service Flow. The docsQosParamSetType index indicates whether the active, admitted, or provisioned QOS Parameter Set is being described by the row. Only the QOS Parameter Sets of Docsis 1.1 service flows are represented in this table. Docsis 1.0 QOS service profiles are not represented in this table. Each row corresponds to a DOCSIS QOS Parameter Set as signaled via DOCSIS MAC management messages. Each object in the row corresponds to one or part of one DOCSIS 1.1 Service Flow Encoding. The docsQosParamSetBitMap object in the row indicates which particular parameters were signalled in the original registration or dynamic service request message that created the QOS Parameter Set. In many cases, even if a QOS Parameter Set parameter was not signalled, the DOCSIS specification calls for a default value to be used. That default value is reported as the value of the corresponding object in this row. Many objects are not applicable depending on the service flow direction or upstream scheduling type. The object value reported in this case Expires April 2001 [Page 33]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 is specified in the DESCRIPTION clause. " ::= { docsQosMIBObjects 2 } docsQosParamSetEntry OBJECT-TYPE SYNTAX DocsQosParamSetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A unique set of QOS parameters." INDEX { ifIndex, docsQosServiceFlowId, docsQosParamSetType } ::= { docsQosParamSetTable 2 } -- Type of docsQosParamSet Entry { docsQosParamSetTable 1 } was -- changed with revision -03 DocsQosParamSetEntry ::= SEQUENCE { docsQosParamSetServiceClassName DisplayString, docsQosParamSetPriority Integer32, docsQosParamSetMaxTrafficRate BitRate, docsQosParamSetMaxTrafficBurst Unsigned32, docsQosParamSetMinReservedRate BitRate, docsQosParamSetMinReservedPkt Integer32, docsQosParamSetActiveTimeout Integer32, docsQosParamSetAdmittedTimeout Integer32, docsQosParamSetMaxConcatBurst Integer32, docsQosParamSetSchedulingType SchedulingType, docsQosParamSetNomPollInterval Unsigned32, docsQosParamSetTolPollJitter Unsigned32, docsQosParamSetUnsolicitGrantSize Integer32, docsQosParamSetNomGrantInterval Unsigned32, docsQosParamSetTolGrantJitter Unsigned32, docsQosParamSetGrantsPerInterval Integer32, docsQosParamSetTosAndMask OCTET STRING, docsQosParamSetTosOrMask OCTET STRING, docsQosParamSetMaxLatency Unsigned32, docsQosParamSetType INTEGER, docsQosParamSetRequestPolicyOct OCTET STRING, docsQosParamSetBitMap BITS } -- Removed docsQosParamSetRowType { docsQosParamSetEntry 1 } -- with revision -03 -- Removed docsQosParamSetIndex { docsQosParamSetEntry 2 } -- with revision -03 -- Removed docsQosParamSetRowStatus { docsQosParamSetEntry 3} Expires April 2001 [Page 34]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 -- with revision -03 docsQosParamSetServiceClassName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Refers to the Service Class Name that the parameter set values were derived. If the referenced parameter is not present in the corresponding DOCSIS QOS Parameter Set, the default value of this object is a zero length string. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.3.4" ::= { docsQosParamSetEntry 4 } docsQosParamSetPriority OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS read-only STATUS current DESCRIPTION "The relative priority of a service flow. Higher numbers indicate higher priority. This priority should only be used to differentiate service flow with identical parameter sets. If the referenced parameter is not present in the corresponding DOCSIS QOS Parameter Set, the default value of this object is 0. If the parameter is not applicable, the reported value is 0. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.5.2" ::= { docsQosParamSetEntry 5 } docsQosParamSetMaxTrafficRate OBJECT-TYPE SYNTAX BitRate MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum sustained traffic rate allowed for this service flow in bits/sec. Must count all MAC frame data PDU from the bytes following the MAC header HCS to the end of the CRC. The number of bytes forwarded is limited during any time interval. The value 0 means no maximum traffic rate is enforced. This object applies to both upstream and downstream service flows. If the referenced parameter is not present in the corresponding DOCSIS QOS Parameter Set, the default value of this object is 0. If the parameter is not applicable, it is reported as 0. " Expires April 2001 [Page 35]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.5.3" ::= { docsQosParamSetEntry 6 } docsQosParamSetMaxTrafficBurst OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the token bucket size in bytes for this parameter set. The value is calculated from the byte following the MAC header HCS to the end of the CRC. This object is applied in conjunction with docsQosParamSetMaxTrafficRate to calculate maximum sustained traffic rate. If the referenced parameter is not present in the corresponding DOCSIS QOS Parameter Set, the default value of this object for scheduling types bestEffort (2), nonRealTimePollingService(3), and realTimePollingService(4) is 1522. If this parameter is not applicable, it is reported as 0. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.5.4" ::= { docsQosParamSetEntry 7 } docsQosParamSetMinReservedRate OBJECT-TYPE SYNTAX BitRate MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the guaranteed minimum rate in bits/sec for this parameter set. The value is calculated from the byte following the MAC header HCS to the end of the CRC. The default value of 0 has the meaning that no bandwidth is reserved. If the referenced parameter is not present in the corresponding DOCSIS QOS Parameter Set, the default value of this object is 0. If the parameter is not applicable, it is reported as 0. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.5.5" ::= { docsQosParamSetEntry 8 } docsQosParamSetMinReservedPkt OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies an assumed minimum packet size in bytes for which the docsQosParamSetMinReservedRate will be provided. The value is calculated from Expires April 2001 [Page 36]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 the byte following the MAC header HCS to the end of the CRC. If the referenced parameter is omitted from a DOCSIS QOS parameter set, the default value is CMTS implementation dependent. In this case, the CMTS reports the default value it is using and the CM reports a value of 0. If the referenced parameter is not applicable to the direction or scheduling type of the service flow, both CMTS and CM report this object's value as 0. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.5.6" ::= { docsQosParamSetEntry 9 } docsQosParamSetActiveTimeout OBJECT-TYPE SYNTAX Integer32 (0..65535) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the maximum duration in seconds that resources remain unused on an active service flow before CMTS signals that both active and admitted parameters set are null. The default value of 0 signifies an infinite amount of time. If the referenced parameter is not present in the corresponding DOCSIS QOS Parameter Set, the default value of this object is 0. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.5.7" ::= { docsQosParamSetEntry 10 } docsQosParamSetAdmittedTimeout OBJECT-TYPE SYNTAX Integer32 (0..65535) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the maximum duration in seconds that resources remain in admitted state before resources must be released. The value of 0 signifies an infinite amount of time. If the referenced parameter is not present in the corresponding DOCSIS QOS Parameter Set, the default value of this object is 200. " Expires April 2001 [Page 37]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.5.8" DEFVAL { 200 } ::= { docsQosParamSetEntry 11 } docsQosParamSetMaxConcatBurst OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the maximum concatenated burst in bytes which an upstream service flow is allowed. The value is calculated from the FC byte of the Concatenation MAC Header to the last CRC byte in of the last concatenated MAC frame, inclusive. The value of 0 specifies no maximum burst. If the referenced parameter is not present in the corresponding DOCSIS QOS Parameter Set, the default value of this object is 0. If the parameter is not applicable, this object's value is reported as 0. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.6.1" ::= { docsQosParamSetEntry 12 } docsQosParamSetSchedulingType OBJECT-TYPE SYNTAX SchedulingType MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the upstream scheduling service used for upstream service flow. If the referenced parameter is not present in the corresponding DOCSIS QOS Parameter Set of an upstream service flow, the default value of this object is bestEffort(2). For QOS parameter sets of downstream service flows, this object's value is reported as undefined(1). " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.6.2" ::= { docsQosParamSetEntry 13 } -- Changed type of docsQosParamSetRequestPolicy { docsQosParamSetEntry 14 } -- to docsQosParamSetRequestPolicyOct { docsQosParamSetEntry 25 } docsQosParamSetNomPollInterval OBJECT-TYPE SYNTAX Unsigned32 UNITS "microseconds" MAX-ACCESS read-only STATUS current Expires April 2001 [Page 38]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 DESCRIPTION "Specifies the nominal interval in microseconds between successive unicast request opportunities on an upstream service flow. This object applies only to upstream service flows with schedulingType of value nonRealTimePollingService(3), realTimePollingService(4), and unsolictedGrantServiceWithAD(5). The parameter is mandatory for realTimePollingService(4). If the parameter is omitted with nonRealTimePollingService(3), the CMTS uses an implementation dependent value. If the parameter is omitted with unsolictedGrantServiceWithAD(5), the CMTS uses as a default value the value of the Nominal Grant Interval parameter. In all cases, the CMTS reports the value it is using when the parameter is applicable. The CM reports the signaled parameter value if it was signaled, and 0 otherwise. If the referenced parameter is not applicable to the direction or scheduling type of the corresponding DOCSIS QOS Parameter Set, both CMTS and CM report this object's value as 0. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.6.4" ::= { docsQosParamSetEntry 15 } docsQosParamSetTolPollJitter OBJECT-TYPE SYNTAX Unsigned32 UNITS "microseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the maximum amount of time in microseconds that the unicast request interval may be delayed from the nominal periodic schedule on an upstream service flow. This parameter is applicable only to upstream service flows with a Schedulingtype of realTimePollingService(4) or unsolictedGrantServiceWithAD(5). If the referenced parameter is applicable but not present in the corresponding DOCSIS QOS Parameter Set, the CMTS uses an implementation dependent value and reports the value it is using. The CM reports a value of 0 in this case. If the parameter is not applicable to the Expires April 2001 [Page 39]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 direction or upstream scheduling type of the service flow, both CMTS and CM report this object's value as 0. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.6.5" ::= { docsQosParamSetEntry 16 } docsQosParamSetUnsolicitGrantSize OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the unsolicited grant size in bytes. The grant size includes the entired MAC frame data PDU from the Frame Control byte to end of the MAC frame. The referenced parameter is applicable only for upstream flows with a SchedulingType of of unsolicitedGrantServicewithAD(5) or unsolicitedGrantService(6), and is mandatory when applicable. Both CMTS and CM report the signaled value of the parameter in this case. If the referenced parameter is not applicable to the direction or scheduling type of the corresponding DOCSIS QOS Parameter Set, both CMTS and CM report this object's value as 0. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.6.6" ::= { docsQosParamSetEntry 17 } docsQosParamSetNomGrantInterval OBJECT-TYPE SYNTAX Unsigned32 UNITS "microseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the nominal interval in microseconds between successive data grant opportunities on an upstream service flow. The referenced parameter is applicable only for upstream flows with a SchedulingType of of unsolicitedGrantServicewithAD(5) or unsolicitedGrantService(6), and is mandatory when applicable. Both CMTS and CM report the signaled value of the parameter in this case. If the referenced parameter is not applicable to the direction or scheduling type of the corresponding DOCSIS QOS Parameter Set, both Expires April 2001 [Page 40]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 CMTS and CM report this object's value as 0. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.6.7" ::= { docsQosParamSetEntry 18 } docsQosParamSetTolGrantJitter OBJECT-TYPE SYNTAX Unsigned32 UNITS "microseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the maximum amount of time in microseconds that the transmission opportunities may be delayed from the nominal periodic schedule. The referenced parameter is applicable only for upstream flows with a SchedulingType of of unsolicitedGrantServicewithAD(5) or unsolicitedGrantService(6), and is mandatory when applicable. Both CMTS and CM report the signaled value of the parameter in this case. If the referenced parameter is not applicable to the direction or scheduling type of the corresponding DOCSIS QOS Parameter Set, both CMTS and CM report this object's value as 0. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.6.8" ::= { docsQosParamSetEntry 19 } docsQosParamSetGrantsPerInterval OBJECT-TYPE SYNTAX Integer32 (0..127) MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the number of data grants per Nominal Grant Interval (docsQosParamSetNomGrantInterval). The referenced parameter is applicable only for upstream flows with a SchedulingType of of unsolicitedGrantServicewithAD(5) or unsolicitedGrantService(6), and is mandatory when applicable. Both CMTS and CM report the signaled value of the parameter in this case. If the referenced parameter is not applicable to the direction or scheduling type of the corresponding DOCSIS QOS Parameter Set, both CMTS and CM report this object's value as 0. " Expires April 2001 [Page 41]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.6.9" ::= { docsQosParamSetEntry 20 } docsQosParamSetTosAndMask OBJECT-TYPE SYNTAX OCTET STRING (SIZE(1)) MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the AND mask for IP TOS byte for overwriting IP packets TOS value. The IP packets TOS byte is bitwise ANDed with docsQosParamSetTosAndMask and result is bitwise ORed with docsQosParamSetTosORMask and result is written to IP packet TOS byte. A value of 'FF'H for docsQosParamSetTosAndMask and a value of '00'H for docsQosParamSetTosOrMask means that IP Packet TOS byte is not overwritten. This combination is reported if the referenced parameter is not present in a QOS Parameter Set." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.6.10" ::= { docsQosParamSetEntry 21 } docsQosParamSetTosOrMask OBJECT-TYPE SYNTAX OCTET STRING (SIZE(1)) MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the OR mask for IP TOS byte. See the description of docsQosParamSetTosAndMask for further details." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.6.10" ::= { docsQosParamSetEntry 22 } docsQosParamSetMaxLatency OBJECT-TYPE SYNTAX Unsigned32 UNITS "microseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the maximum latency between the reception of a packet by the CMTS on its NSI and the forwarding of the packet to the RF interface. A value of 0 signifies no maximum latency enforced. This object only applies to downstream service flows. If the referenced parameter is not present in the corresponding downstream DOCSIS QOS Parameter Set, the default value is 0. This parameter is not applicable to upstream DOCSIS QOS Parameter Sets, and its value is reported as 0 in this case. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.7.1" ::= { docsQosParamSetEntry 23 } Expires April 2001 [Page 42]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 docsQosParamSetType OBJECT-TYPE SYNTAX INTEGER { active (1), admitted (2), provisioned (3) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "Defines the type of the QOS parameter set defined by this row. active(1) indicates the Active QOS parameter set, describing the service currently being provided by the Docsis MAC domain to the service flow. admitted(2) indicates the Admitted QOS Parameter Set, describing services reserved by by the Docsis MAC domain for use by the service flow. provisioned (3) describes the QOS Parameter Set defined in the DOCSIS CM Configuration file for the service flow." REFERENCE "SP-RFIv1.1-I05-000714, 8.1.5" ::= { docsQosParamSetEntry 24 } docsQosParamSetRequestPolicyOct OBJECT-TYPE SYNTAX OCTET STRING (SIZE(4)) -- A 32-bit mask represented most significant byte -- first. The 32 bit integer represented in this manner -- equals the binary value of the referenced integer -- parameter of the DOCSIS RFI specification. -- The BITS syntax is not used in order to avoid -- the confusion caused by different bit numbering -- conventions. MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies which transmit interval opportunities the CM omits for upstream transmission requests and packet transmissions. This object takes its default value for downstream service flows. Unless otherwise indicated, a bit value of 1 means that a CM must *not* use that opportunity for upstream transmission. Calling bit 0 the least significant bit of the least significant (4th) octet, and increasing bit number with significance, the bit definitions are as defined below: broadcastReqOpp(0): all CMs broadcast request opportunities priorityReqMulticastReq(1): priority request multicast request opportunities Expires April 2001 [Page 43]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 reqDataForReq(3): request/data opportunities for requests reqDataForData(4): request/data opportunities for data concatenateData(5): concatenate data fragmentData(6): fragment data suppresspayloadheaders(7): suppress payload headers dropPktsExceedUGSize(8): A value of 1 mean that service flow must drop packet that do not fit in the Unsolicited Grant size If the referenced parameter is not present in a QOS Parameter Set, the value of this object is reported as '00000000'H. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.6.3" ::= { docsQosParamSetEntry 25 } docsQosParamSetBitMap OBJECT-TYPE -- Each bit corresponds to a parameter -- from SP-RFI-v1.1-I05-000714, Appendix C SYNTAX BITS { -- in the indicated section number. trafficPriority(0), -- C.2.2.5.2 maxTrafficRate(1), -- C.2.2.5.3 maxTrafficBurst(2), -- C.2.2.5.4 minReservedRate(3), -- C.2.2.5.5 minReservedPkt(4), -- C.2.2.5.6 activeTimeout(5), -- C.2.2.5.7 admittedTimeout(6), -- C.2.2.5.8 maxConcatBurst(7), -- C.2.2.6.1 schedulingType(8), -- C.2.2.6.2 requestPolicy(9), -- C.2.2.6.3 nomPollInterval(10), -- C.2.2.6.4 tolPollJitter(11), -- C.2.2.6.5 unsolicitGrantSize(12), -- C.2.2.6.6 nomGrantInterval(13), -- C.2.2.6.7 tolGrantJitter(14), -- C.2.2.6.8 grantsPerInterval(15), -- C.2.2.6.9 tosOverwrite(16), -- C.2.2.6.10 maxLatency(17) -- C.2.2.7.1 } MAX-ACCESS read-only Expires April 2001 [Page 44]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 STATUS current DESCRIPTION "This object indicates the set of QOS Parameter Set parameters actually signaled in the DOCSIS registration or dynamic service request message that created the QOS Parameter Set. A bit is set to 1 when the parameter described by the indicated reference section is present in the original request. Note that when Service Class names are expanded, the registration or dynamic response message may contain parameters as expanded by the CMTS based on a stored service class. These expanded parameters are *not* indicated by a 1 bit in this object. Note that even though some QOS Parameter Set parameters may not be signalled in a message (so that the paramater's bit in this object is 0) the DOCSIS specification calls for default values to be used. These default values are reported as the corresponding object's value in the row. Note that BITS objects are encoded most significant bit first. For example, if bits 1 and 16 are set, the value of this object is the octet string '400080'H. " ::= { docsQosParamSetEntry 26 } -- -- Service Flow Table -- docsQosServiceFlowTable OBJECT-TYPE SYNTAX SEQUENCE OF DocsQosServiceFlowEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the set of Docsis-QOS Service Flows in a managed device. " ::= { docsQosMIBObjects 3 } docsQosServiceFlowEntry OBJECT-TYPE SYNTAX DocsQosServiceFlowEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Describes a service flow. An entry in the table exists for each Service Flow ID. The ifIndex is an ifType of docsCableMaclayer(127)." Expires April 2001 [Page 45]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 INDEX { ifIndex, docsQosServiceFlowId } ::= { docsQosServiceFlowTable 1 } DocsQosServiceFlowEntry ::= SEQUENCE { docsQosServiceFlowId Unsigned32, docsQosServiceFlowSID Unsigned32, docsQosServiceFlowDirection IfDirection, docsQosServiceFlowPrimary TruthValue } docsQosServiceFlowId OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index assigned to a service flow by CMTS." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.3.2" ::= { docsQosServiceFlowEntry 1 } -- Remove docsQosServiceFlowProvisionedParamSetIndex -- {docsQosServiceFlowEntry 2} with revision -03 -- Remove docsQosServiceFlowAdmittedParamSetIndex -- {docsQosServiceFlowEntry 3} with revision -03 -- Remove docsQosServiceFlowActiveParamSetIndex -- {docsQosServiceFlowEntry 4} with revision -03 docsQosServiceFlowSID OBJECT-TYPE SYNTAX Unsigned32 (0..16383) MAX-ACCESS read-only STATUS current DESCRIPTION "Service Identifier (SID) assigned to an admitted or active service flow. This object reports a value of 0 if a Service Id is not associated with the service flow. Only active or admitted upstream service flows will have a Service Id (SID)." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.3.3" ::= { docsQosServiceFlowEntry 6 } docsQosServiceFlowDirection OBJECT-TYPE SYNTAX IfDirection MAX-ACCESS read-only STATUS current DESCRIPTION "The direction of the service flow." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.1/2" ::= { docsQosServiceFlowEntry 7 } docsQosServiceFlowPrimary OBJECT-TYPE SYNTAX TruthValue Expires April 2001 [Page 46]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 MAX-ACCESS read-only STATUS current DESCRIPTION "Object reflects whether service flow is the primary or a secondary service flow. A primary service flow is the default service flow for otherwise unclassified traffic and all MAC messages." REFERENCE "SP-RFIv1.1-I05-000714, Section 8.1 " ::= { docsQosServiceFlowEntry 8 } -- Moved docsQosServiceFlow'ActiveTimeout, 'AdmittedTimeout, -- 'SchedulingType, 'RequestPolicy, 'TosAndMask, and 'TosOrMask -- back to docsQosParamSetTable with QOS-MIB-04. -- -- Service Flow Stats Table -- docsQosServiceFlowStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF DocsQosServiceFlowStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes statistics associated with the Service Flows in a managed device. " ::= { docsQosMIBObjects 4 } docsQosServiceFlowStatsEntry OBJECT-TYPE SYNTAX DocsQosServiceFlowStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Describes a set of service flow statistics. An entry in the table exists for each Service Flow ID. The ifIndex is an ifType of docsCableMaclayer(127)." INDEX { ifIndex, docsQosServiceFlowId } ::= { docsQosServiceFlowStatsTable 1 } DocsQosServiceFlowStatsEntry ::= SEQUENCE { docsQosServiceFlowPkts Counter32, docsQosServiceFlowOctets Counter32, docsQosServiceFlowTimeCreated TimeStamp, docsQosServiceFlowTimeActive Counter32, docsQosServiceFlowPHSUnknowns Counter32, docsQosServiceFlowPolicedDropPkts Counter32, docsQosServiceFlowPolicedDelayPkts Counter32 } docsQosServiceFlowPkts OBJECT-TYPE Expires April 2001 [Page 47]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packet counted on this service flow." ::= { docsQosServiceFlowStatsEntry 1 } docsQosServiceFlowOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of octets counted on this service flow after payload header suppression." ::= { docsQosServiceFlowStatsEntry 2 } docsQosServiceFlowTimeCreated OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime when the service flow was created." ::= { docsQosServiceFlowStatsEntry 3 } docsQosServiceFlowTimeActive OBJECT-TYPE SYNTAX Counter32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The total time that service flow has been active." ::= { docsQosServiceFlowStatsEntry 4 } docsQosServiceFlowPHSUnknowns OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packet with unknown payload header suppression index." ::= { docsQosServiceFlowStatsEntry 5 } docsQosServiceFlowPolicedDropPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets dropped due to policing of the service flow, especially to limit the maximum rate of the flow." ::= { docsQosServiceFlowStatsEntry 6 } docsQosServiceFlowPolicedDelayPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only Expires April 2001 [Page 48]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 STATUS current DESCRIPTION "The number of packet delayed due to policing of the service flow, especially to limit the maximum rate of the flow." ::= { docsQosServiceFlowStatsEntry 7 } -- -- Upstream Service Flow Stats Table (CMTS ONLY) -- docsQosUpstreamStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF DocsQosUpstreamStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes statistics associated with upstream service flows. All counted frames must be received without an FCS error." ::= { docsQosMIBObjects 5 } docsQosUpstreamStatsEntry OBJECT-TYPE SYNTAX DocsQosUpstreamStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Describes a set of upstream service flow statistics. An entry in the table exists for each upstream Service Flow in a managed device. The ifIndex is an ifType of docsCableMaclayer(127)." INDEX { ifIndex, docsQosSID } ::= { docsQosUpstreamStatsTable 1 } DocsQosUpstreamStatsEntry ::= SEQUENCE { docsQosSID Integer32, docsQosUpstreamFragments Counter32, docsQosUpstreamFragDiscards Counter32, docsQosUpstreamConcatBursts Counter32 } docsQosSID OBJECT-TYPE SYNTAX Integer32 (1..16383) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Identifies a service id for an admitted or active upstream service flow." ::= { docsQosUpstreamStatsEntry 1 } -- Renamed in revision -03 from docsQosUpstreamFragPkts docsQosUpstreamFragments OBJECT-TYPE SYNTAX Counter32 Expires April 2001 [Page 49]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of fragmentation headers received on an upstream service flow, regardless of whether the fragment was correctly reassembled into a valid packet. " ::= { docsQosUpstreamStatsEntry 2 } docsQosUpstreamFragDiscards OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of upstream fragments discarded and not assembled into a valid upstream packet." ::= { docsQosUpstreamStatsEntry 3 } docsQosUpstreamConcatBursts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of concatenation headers received on an upstream service flow." ::= { docsQosUpstreamStatsEntry 4 } -- -- Dynamic Service Stats Table -- docsQosDynamicServiceStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF DocsQosDynamicServiceStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes statistics associated with the Dynamic Service Flows in a managed device. " ::= { docsQosMIBObjects 6 } docsQosDynamicServiceStatsEntry OBJECT-TYPE SYNTAX DocsQosDynamicServiceStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Describes a set of dynamic service flow statistics. Two entries exist for each Docsis mac layer interface for the upstream and downstream direction. On the CMTS, the downstream direction row indicates messages transmitted or transactions originated by the CMTS. The upstream direction row indicates messages received or transaction originated by the CM. On the CM, the downstream direction row indicates messages received or transactions originated by the CMTS. The upstream direction row indicates messages transmitted by the CM or Expires April 2001 [Page 50]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 transactions originated by the CM. The ifIndex is an ifType of docsCableMaclayer(127)." INDEX { ifIndex, docsQosIfDirection } ::= { docsQosDynamicServiceStatsTable 1 } DocsQosDynamicServiceStatsEntry ::= SEQUENCE { docsQosIfDirection IfDirection, docsQosDSAReqs Counter32, docsQosDSARsps Counter32, docsQosDSAAcks Counter32, docsQosDSCReqs Counter32, docsQosDSCRsps Counter32, docsQosDSCAcks Counter32, docsQosDSDReqs Counter32, docsQosDSDRsps Counter32, docsQosDynamicAdds Counter32, docsQosDynamicAddFails Counter32, docsQosDynamicChanges Counter32, docsQosDynamicChangeFails Counter32, docsQosDynamicDeletes Counter32, docsQosDynamicDeleteFails Counter32, docsQosDCCReqs Counter32, docsQosDCCRsps Counter32, docsQosDCCAcks Counter32, docsQosDCCs Counter32, docsQosDCCFails Counter32 } docsQosIfDirection OBJECT-TYPE SYNTAX IfDirection MAX-ACCESS not-accessible STATUS current DESCRIPTION "The direction of interface." ::= { docsQosDynamicServiceStatsEntry 1 } docsQosDSAReqs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Dynamic Service Addition Requests" ::= { docsQosDynamicServiceStatsEntry 2 } docsQosDSARsps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Dynamic Service Addition Responses" ::= { docsQosDynamicServiceStatsEntry 3 } Expires April 2001 [Page 51]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 docsQosDSAAcks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Dynamic Service Addition Acknowledgements." ::= { docsQosDynamicServiceStatsEntry 4 } docsQosDSCReqs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Dynamic Service Change Requests" ::= { docsQosDynamicServiceStatsEntry 5 } docsQosDSCRsps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Dynamic Service Change Responses" ::= { docsQosDynamicServiceStatsEntry 6 } docsQosDSCAcks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Dynamic Service Change Acknowlegements." ::= { docsQosDynamicServiceStatsEntry 7 } docsQosDSDReqs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Dynamic Service Delete Requests" ::= { docsQosDynamicServiceStatsEntry 8 } docsQosDSDRsps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Dynamic Service Delete Responses" ::= { docsQosDynamicServiceStatsEntry 9 } docsQosDynamicAdds OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of successful Dynamic Service Addition transactions." ::= { docsQosDynamicServiceStatsEntry 10 } docsQosDynamicAddFails OBJECT-TYPE Expires April 2001 [Page 52]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of failed Dynamic Service Addition transactions." ::= { docsQosDynamicServiceStatsEntry 11 } docsQosDynamicChanges OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of successful Dynamic Service Change transactions." ::= { docsQosDynamicServiceStatsEntry 12 } docsQosDynamicChangeFails OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of failed Dynamic Service Change transactions." ::= { docsQosDynamicServiceStatsEntry 13 } docsQosDynamicDeletes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of successful Dynamic Service Delete transactions." ::= { docsQosDynamicServiceStatsEntry 14 } docsQosDynamicDeleteFails OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of failed Dynamic Service Delete transactions." ::= { docsQosDynamicServiceStatsEntry 15 } docsQosDCCReqs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Dynamic Channel Change Request messages traversing an interface. This count is nonzero only on downstream direction rows." ::= { docsQosDynamicServiceStatsEntry 16 } docsQosDCCRsps OBJECT-TYPE SYNTAX Counter32 Expires April 2001 [Page 53]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Dynamic Channel Change Response messages traversing an interface. This count is nonzero only on upstream direction rows." ::= { docsQosDynamicServiceStatsEntry 17 } docsQosDCCAcks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Dynamic Channel Change Acknowledgement messages traversing an interface. This count is nonzero only on downstream direction rows." ::= { docsQosDynamicServiceStatsEntry 18 } docsQosDCCs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of successful Dynamic Channel Change transactions. This count is nonzero only on downstream direction rows." ::= { docsQosDynamicServiceStatsEntry 19 } docsQosDCCFails OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of failed Dynamic Channel Change transactions. This count is nonzero only on downstream direction rows." ::= { docsQosDynamicServiceStatsEntry 20 } -- -- Service Flow Log Table (CMTS ONLY) -- docsQosServiceFlowLogTable OBJECT-TYPE SYNTAX SEQUENCE OF DocsQosServiceFlowLogEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains a log of the disconnected Service Flows in a managed device." ::= { docsQosMIBObjects 7 } docsQosServiceFlowLogEntry OBJECT-TYPE SYNTAX DocsQosServiceFlowLogEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The information regarding a single disconnected Expires April 2001 [Page 54]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 service flow." INDEX { docsQosServiceFlowLogIndex } ::= { docsQosServiceFlowLogTable 1 } DocsQosServiceFlowLogEntry ::= SEQUENCE { docsQosServiceFlowLogIndex Unsigned32, docsQosServiceFlowLogIfIndex InterfaceIndex, docsQosServiceFlowLogSFID Unsigned32, docsQosServiceFlowLogCmMac MacAddress, docsQosServiceFlowLogPkts Counter32, docsQosServiceFlowLogOctets Counter32, docsQosServiceFlowLogTimeDeleted TimeStamp, docsQosServiceFlowLogTimeCreated TimeStamp, docsQosServiceFlowLogTimeActive Counter32, docsQosServiceFlowLogDirection IfDirection, docsQosServiceFlowLogPrimary TruthValue, docsQosServiceFlowLogServiceClassName DisplayString, docsQosServiceFlowLogPolicedDropPkts Counter32, docsQosServiceFlowLogPolicedDelayPkts Counter32, docsQosServiceFlowLogControl INTEGER } docsQosServiceFlowLogIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "Unique index for a logged service flow." ::= { docsQosServiceFlowLogEntry 1 } docsQosServiceFlowLogIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The ifIndex of ifType docsCableMacLayter(127) on the CMTS where the service flow was present." ::= { docsQosServiceFlowLogEntry 2 } docsQosServiceFlowLogSFID OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "The index assigned to the service flow by the CMTS." ::= { docsQosServiceFlowLogEntry 3 } docsQosServiceFlowLogCmMac OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The MAC address for the cable modem associated with Expires April 2001 [Page 55]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 the service flow." ::= { docsQosServiceFlowLogEntry 4 } docsQosServiceFlowLogPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets counted on this service flow after payload header suppression." ::= { docsQosServiceFlowLogEntry 5 } docsQosServiceFlowLogOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of octets counted on this service flow after payload header suppression." ::= { docsQosServiceFlowLogEntry 6 } docsQosServiceFlowLogTimeDeleted OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime when the service flow was deleted." ::= { docsQosServiceFlowLogEntry 7 } docsQosServiceFlowLogTimeCreated OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime when the service flow was created." ::= { docsQosServiceFlowLogEntry 8 } docsQosServiceFlowLogTimeActive OBJECT-TYPE SYNTAX Counter32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The total time that service flow was active." ::= { docsQosServiceFlowLogEntry 9 } -- docsQosServiceFlowLogControl was formerly { docsQosServiceFlowLogEntry 10} -- and was renumbered in version -04. docsQosServiceFlowLogDirection OBJECT-TYPE SYNTAX IfDirection MAX-ACCESS read-only Expires April 2001 [Page 56]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 STATUS current DESCRIPTION "The value of docsQosServiceFlowDirection for the service flow." ::= { docsQosServiceFlowLogEntry 11} docsQosServiceFlowLogPrimary OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The value of docsQosServiceFlowPrimary for the service flow." ::= { docsQosServiceFlowLogEntry 12} docsQosServiceFlowLogServiceClassName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The value of docsQosParamSetServiceClassName for the provisioned QOS Parameter Set of the service flow." ::= { docsQosServiceFlowLogEntry 13} docsQosServiceFlowLogPolicedDropPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The final value of docsQosServiceFlowPolicedDropPkts for the service flow." ::= { docsQosServiceFlowLogEntry 14} docsQosServiceFlowLogPolicedDelayPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The final value of docsQosServiceFlowPolicedDelayPkts for the service flow." ::= { docsQosServiceFlowLogEntry 15} docsQosServiceFlowLogControl OBJECT-TYPE SYNTAX INTEGER { active(1), destroy(6) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this object to the value destroy(6) removes this entry from the table. Reading this object return the value active(1)." ::= { docsQosServiceFlowLogEntry 16} Expires April 2001 [Page 57]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 -- -- Service Class Table (CMTS ONLY) -- docsQosServiceClassTable OBJECT-TYPE SYNTAX SEQUENCE OF DocsQosServiceClassEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the set of Docsis-QOS Service Classes in a CMTS. " ::= { docsQosMIBObjects 8 } docsQosServiceClassEntry OBJECT-TYPE SYNTAX DocsQosServiceClassEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A provisioned service class on a CMTS. Each entry defines a template for certain DOCSIS QOS Parameter Set values. When a CM creates or modifies an Admitted QOS Parameter Set for a Service Flow, it may reference a Service Class Name instead of providing explicit QOS Parameter Set values. In this case, the CMTS populates the QOS Parameter Set with the applicable corresponding values from the named Service Class. Subsequent changes to a Service Class row do *not* affect the QOS Parameter Set values of any service flows already admitted. A service class template applies to only a single direction, as indicated in the docsQosServiceClassDirection object. " INDEX { docsQosServiceClassName } ::= { docsQosServiceClassTable 1 } DocsQosServiceClassEntry ::= SEQUENCE { docsQosServiceClassName DisplayString (SIZE(1..15)), docsQosServiceClassStatus RowStatus, docsQosServiceClassPriority Integer32, docsQosServiceClassMaxTrafficRate BitRate, docsQosServiceClassMaxTrafficBurst Unsigned32, docsQosServiceClassMinReservedRate BitRate, docsQosServiceClassMinReservedPkt Integer32, docsQosServiceClassMaxConcatBurst Integer32, docsQosServiceClassNomPollInterval Unsigned32, docsQosServiceClassTolPollJitter Unsigned32, docsQosServiceClassUnsolicitGrantSize Integer32, docsQosServiceClassNomGrantInterval Unsigned32, docsQosServiceClassTolGrantJitter Unsigned32, Expires April 2001 [Page 58]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 docsQosServiceClassGrantsPerInterval Integer32, docsQosServiceClassMaxLatency Unsigned32, docsQosServiceClassActiveTimeout Integer32, docsQosServiceClassAdmittedTimeout Integer32, docsQosServiceClassSchedulingType SchedulingType, docsQosServiceClassRequestPolicy OCTET STRING (SIZE(4)), docsQosServiceClassTosAndMask OCTET STRING (SIZE(1)), docsQosServiceClassTosOrMask OCTET STRING (SIZE(1)), docsQosServiceClassDirection IfDirection } docsQosServiceClassName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..15)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Service Class Name. DOCSIS specifies that the maximum size is 15 printable ASCII characters with a terminating zero. The terminating zero is not represented in this DisplayString syntax object. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.3.4" ::= { docsQosServiceClassEntry 1 } -- docsQosServiceClassParamSetIndex { docsQosServiceClassEntry 2 } -- was removed in revision -03 docsQosServiceClassStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Used to create or delete rows in this table." ::= { docsQosServiceClassEntry 3 } docsQosServiceClassPriority OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS read-create STATUS current DESCRIPTION "Template for docsQosParamSetPriority." DEFVAL { 0 } ::= { docsQosServiceClassEntry 4 } docsQosServiceClassMaxTrafficRate OBJECT-TYPE SYNTAX BitRate MAX-ACCESS read-create STATUS current DESCRIPTION "Template for docsQosParamSetMaxTrafficRate." DEFVAL { 0 } ::= { docsQosServiceClassEntry 5 } docsQosServiceClassMaxTrafficBurst OBJECT-TYPE SYNTAX Unsigned32 Expires April 2001 [Page 59]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 MAX-ACCESS read-create STATUS current DESCRIPTION "Template for docsQosParamSetMaxTrafficBurst." DEFVAL { 1522 } ::= { docsQosServiceClassEntry 6 } docsQosServiceClassMinReservedRate OBJECT-TYPE SYNTAX BitRate MAX-ACCESS read-create STATUS current DESCRIPTION "Template for docsQosParamSEtMinReservedRate." DEFVAL { 0 } ::= { docsQosServiceClassEntry 7 } docsQosServiceClassMinReservedPkt OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "Template for docsQosParamSetMinReservedPkt." ::= { docsQosServiceClassEntry 8 } docsQosServiceClassMaxConcatBurst OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "Template for docsQosParamSetMaxConcatBurst." DEFVAL { 0 } ::= { docsQosServiceClassEntry 9 } docsQosServiceClassNomPollInterval OBJECT-TYPE SYNTAX Unsigned32 UNITS "microseconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Template for docsQosParamSetNomPollInterval." DEFVAL { 0 } ::= { docsQosServiceClassEntry 10 } docsQosServiceClassTolPollJitter OBJECT-TYPE SYNTAX Unsigned32 UNITS "microseconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Template for docsQosParamSetTolPollJitter." DEFVAL { 0 } ::= { docsQosServiceClassEntry 11 } docsQosServiceClassUnsolicitGrantSize OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-create STATUS current Expires April 2001 [Page 60]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 DESCRIPTION "Template for docsQosParamSetUnsolicitGrantSize." DEFVAL { 0 } ::= { docsQosServiceClassEntry 12 } docsQosServiceClassNomGrantInterval OBJECT-TYPE SYNTAX Unsigned32 UNITS "microseconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Template for docsQosParamSetNomGrantInterval." DEFVAL { 0 } ::= { docsQosServiceClassEntry 13 } docsQosServiceClassTolGrantJitter OBJECT-TYPE SYNTAX Unsigned32 UNITS "microseconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Template for docsQosParamSetTolGrantJitter." DEFVAL { 0 } ::= { docsQosServiceClassEntry 14 } docsQosServiceClassGrantsPerInterval OBJECT-TYPE SYNTAX Integer32 (0..127) MAX-ACCESS read-create STATUS current DESCRIPTION "Template for docsQosParamSetGrantsPerInterval." DEFVAL { 0 } ::= { docsQosServiceClassEntry 15 } docsQosServiceClassMaxLatency OBJECT-TYPE SYNTAX Unsigned32 UNITS "microseconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Template for docsQosParamSetClassMaxLatency." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.7.1" DEFVAL { 0 } ::= { docsQosServiceClassEntry 16 } docsQosServiceClassActiveTimeout OBJECT-TYPE SYNTAX Integer32 (0..65535) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Template for docsQosServiceFlowActiveTimeout." DEFVAL { 0 } ::= { docsQosServiceClassEntry 17 } docsQosServiceClassAdmittedTimeout OBJECT-TYPE SYNTAX Integer32 (0..65535) Expires April 2001 [Page 61]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Template for docsQosServiceFlowAdmittedTimeout." DEFVAL { 200 } ::= { docsQosServiceClassEntry 18 } docsQosServiceClassSchedulingType OBJECT-TYPE SYNTAX SchedulingType MAX-ACCESS read-create STATUS current DESCRIPTION "Template for docsQosServiceFlowSchedulingType." DEFVAL { bestEffort } ::= { docsQosServiceClassEntry 19 } docsQosServiceClassRequestPolicy OBJECT-TYPE SYNTAX OCTET STRING (SIZE(4)) MAX-ACCESS read-create STATUS current DESCRIPTION "Template for docsQosServiceFlowRequestPolicy." DEFVAL { '00000000'H } -- no bits are set ::= { docsQosServiceClassEntry 20 } docsQosServiceClassTosAndMask OBJECT-TYPE SYNTAX OCTET STRING (SIZE(1)) MAX-ACCESS read-create STATUS current DESCRIPTION "Template for docsQosServiceFlowTosAndMask." DEFVAL { 'FF'H } ::= { docsQosServiceClassEntry 21 } docsQosServiceClassTosOrMask OBJECT-TYPE SYNTAX OCTET STRING (SIZE(1)) MAX-ACCESS read-create STATUS current DESCRIPTION "Template for docsQosServiceFlowTosOrMask." DEFVAL { '00'H } ::= { docsQosServiceClassEntry 22 } docsQosServiceClassDirection OBJECT-TYPE SYNTAX IfDirection MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies whether the service class template applies to upstream or downstream service flows." DEFVAL { upstream } ::= { docsQosServiceClassEntry 23 } -- -- Service Class PolicyTable -- Expires April 2001 [Page 62]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 docsQosServiceClassPolicyTable OBJECT-TYPE SYNTAX SEQUENCE OF DocsQosServiceClassPolicyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the set of Docsis-QOS Service Class Policies. This table is an adjunct to the docsDevFilterPolicy table. Entries in docsDevFilterPolicy table can point to specific rows in this table. This table permits mapping a packet to a service class name of an active service flow so long as a classifier does not exist at a higher priority. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix E.2.1" ::= { docsQosMIBObjects 9 } docsQosServiceClassPolicyEntry OBJECT-TYPE SYNTAX DocsQosServiceClassPolicyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A service class name policy entry." INDEX { docsQosServiceClassPolicyIndex } ::= { docsQosServiceClassPolicyTable 1 } DocsQosServiceClassPolicyEntry ::= SEQUENCE { docsQosServiceClassPolicyIndex Integer32, docsQosServiceClassPolicyName DisplayString, docsQosServiceClassPolicyRulePriority Integer32, docsQosServiceClassPolicyStatus RowStatus } docsQosServiceClassPolicyIndex OBJECT-TYPE SYNTAX Integer32 (1..2147483647) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index value to uniquely identify an entry in this table." ::= { docsQosServiceClassPolicyEntry 1 } docsQosServiceClassPolicyName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "Service Class Name to identify the name of the service class flow to which the packet should be Expires April 2001 [Page 63]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 directed." REFERENCE "SP-RFIv1.1-I05-000714, Appendix E.2.1" ::= { docsQosServiceClassPolicyEntry 2 } docsQosServiceClassPolicyRulePriority OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "Service Class Policy rule priority for the entry." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.3.5" ::= { docsQosServiceClassPolicyEntry 3 } docsQosServiceClassPolicyStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Used to create or delete rows in this table. This object should not be deleted if it is reference by an entry in docsDevFilterPolicy. The reference should be deleted first." ::= { docsQosServiceClassPolicyEntry 4 } -- -- Payload Header Suppression(PHS) Table -- docsQosPHSTable OBJECT-TYPE SYNTAX SEQUENCE OF DocsQosPHSEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes set of payload header suppression entries." ::= { docsQosMIBObjects 10 } docsQosPHSEntry OBJECT-TYPE SYNTAX DocsQosPHSEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A payload header suppression entry. The ifIndex is an ifType of docsCableMaclayer(127). The index docsQosServiceFlowId selects one service flow from the cable MAC layer interface. The docsQosPktClassId index matches an index of the docsQosPktClassTable. " INDEX { ifIndex, docsQosServiceFlowId, docsQosPktClassId } ::= { docsQosPHSTable 1 } Expires April 2001 [Page 64]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 DocsQosPHSEntry ::= SEQUENCE { docsQosPHSField OCTET STRING, docsQosPHSMask OCTET STRING, docsQosPHSSize Integer32, docsQosPHSVerify TruthValue, docsQosPHSIndex Integer32 } -- The object docsQosPHSIndex used as an index {docsQosPHSEntry 1} -- was changed to be a non-index column in revision -03. docsQosPHSField OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "Payload header suppression field defines the bytes of the header which must be suppressed/restored by the sending/receiving device. The number of octets in this object should be the same as the value of docsQosPHSSize." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.10.1" ::= { docsQosPHSEntry 2 } docsQosPHSMask OBJECT-TYPE SYNTAX OCTET STRING(SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "Payload header suppression mask defines the bit mask which used in combination with the docsQosPHSField defines which bytes in header must be suppressed/restored by the sending or receiving device. Each bit of this bit mask corresponds to a byte in the docsQosPHSField, with the least significant bit corresponding to first byte of the docsQosPHSField. Each bit of the bit mask specifies whether of not the corresponding byte should be suppressed in the packet. A bit value of '1' indicates that the byte should be suppressed by the sending device and restored by the receiving device. A bit value of '0' indicates that the byte should not be suppressed by the sending device or restored by the receiving device. If the bit mask does not contain a bit for each byte in the docsQosPHSField then the bit mask is Expires April 2001 [Page 65]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 extended with bit values of '1' to be the necessary length." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.10.3" ::= { docsQosPHSEntry 3 } docsQosPHSSize OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Payload header suppression size specifies the number of bytes in the header to be suppressed and restored. The value of this object must match the number of bytes in the docsQosPHSField." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.10.4" ::= { docsQosPHSEntry 4 } docsQosPHSVerify OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Payload header suppression verification value of 'true' the sender must verify docsQosPHSField is the same as what is contained in the packet to be suppressed." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.10.5" ::= { docsQosPHSEntry 5 } -- Removed dosQosPHSClassifierIndex {docsQosPHSEntry 6} -- in revision -03. docsQosPHSIndex OBJECT-TYPE SYNTAX Integer32 (1..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Payload header suppression index uniquely references the PHS rule for a given service flow." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.10.2" ::= { docsQosPHSEntry 7 } -- -- docsQosCmtsMacToSrvFlowTable (CMTS Only) -- docsQosCmtsMacToSrvFlowTable OBJECT-TYPE SYNTAX SEQUENCE OF DocsQosCmtsMacToSrvFlowEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provide for referencing the service flows associated with a particular cable modem. This allows Expires April 2001 [Page 66]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 for indexing into other docsQos tables that are indexed by docsQosServiceFlowId and ifIndex." ::= { docsQosMIBObjects 11 } docsQosCmtsMacToSrvFlowEntry OBJECT-TYPE SYNTAX DocsQosCmtsMacToSrvFlowEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry is created by CMTS for each service flow connected to this CMTS." INDEX { docsQosCmtsCmMac, docsQosCmtsServiceFlowId } ::= { docsQosCmtsMacToSrvFlowTable 1 } DocsQosCmtsMacToSrvFlowEntry ::= SEQUENCE { docsQosCmtsCmMac MacAddress, docsQosCmtsServiceFlowId Unsigned32, docsQosCmtsIfIndex InterfaceIndex } docsQosCmtsCmMac OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The MAC address for the referenced CM." ::= { docsQosCmtsMacToSrvFlowEntry 1 } docsQosCmtsServiceFlowId OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index assigned to a service flow by CMTS." ::= { docsQosCmtsMacToSrvFlowEntry 2 } docsQosCmtsIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The ifIndex of ifType docsCableMacLayter(127) on the CMTS that is connected to the Cable Modem." ::= { docsQosCmtsMacToSrvFlowEntry 3 } -- -- Placeholder for notifications/traps. -- docsQosNotification OBJECT IDENTIFIER ::= { docsQosMIB 2 } Expires April 2001 [Page 67]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 -- -- Conformance definitions -- docsQosConformance OBJECT IDENTIFIER ::= { docsQosMIB 3 } docsQosGroups OBJECT IDENTIFIER ::= { docsQosConformance 1 } docsQosCompliances OBJECT IDENTIFIER ::= { docsQosConformance 2 } docsQosCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for MCNS Cable Modems and Cable Modem Termination Systems that implement DOCSIS Service Flows." MODULE -- docsQosMIB MANDATORY-GROUPS { docsQosBaseGroup } GROUP docsQosCmtsGroup DESCRIPTION "This group is mandatory for only Cable Modem Termination Systems (CMTS) and not implemented for Cable Modems." GROUP docsQosParamSetGroup DESCRIPTION "This group is mandatory for Cable Modem Termination Systems (CMTS) and Cable Modems. Cable modems only implement objects in this group as read-only." GROUP docsQosSrvClassPolicyGroup DESCRIPTION "This group is optional for Cable Modem Termination Systems (CMTS) and Cable Modems. This group only needs to be implement if policy based service flow classification is implemented. See docsDevPolicyTable in DOCS-CABLE-DEVICE-MIB for more details. " GROUP docsQosServiceClassGroup DESCRIPTION "The docsQosServiceClassTable group of objects. " OBJECT docsQosPktClassPkts DESCRIPTION "This object only needs to be implemented in entries that are classifying packets and not policing packets." ::= { docsQosCompliances 1 } docsQosBaseGroup OBJECT-GROUP OBJECTS { docsQosPktClassDirection, Expires April 2001 [Page 68]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 docsQosPktClassPriority, docsQosPktClassIpTosLow, docsQosPktClassIpTosHigh, docsQosPktClassIpTosMask, docsQosPktClassIpProtocol, docsQosPktClassIpSourceAddr, docsQosPktClassIpSourceMask, docsQosPktClassIpDestAddr, docsQosPktClassIpDestMask, docsQosPktClassSourcePortStart, docsQosPktClassSourcePortEnd, docsQosPktClassDestPortStart, docsQosPktClassDestPortEnd, docsQosPktClassDestMacAddr, docsQosPktClassDestMacMask, docsQosPktClassSourceMacAddr, docsQosPktClassEnetProtocolType, docsQosPktClassEnetProtocol, docsQosPktClassUserPriLow, docsQosPktClassUserPriHigh, docsQosPktClassVlanId, docsQosPktClassState, docsQosPktClassPkts, docsQosPktClassBitMap, docsQosServiceFlowSID, docsQosServiceFlowDirection, docsQosServiceFlowPrimary, docsQosServiceFlowPkts, -- not sure if CM should implement docsQosServiceFlowOctets, docsQosServiceFlowTimeCreated, docsQosServiceFlowTimeActive, docsQosServiceFlowPHSUnknowns, docsQosServiceFlowPolicedDropPkts, docsQosServiceFlowPolicedDelayPkts, docsQosDSAReqs, docsQosDSARsps, docsQosDSAAcks, docsQosDSCReqs, docsQosDSCRsps, docsQosDSCAcks, docsQosDSDReqs, docsQosDSDRsps, docsQosDynamicAdds, docsQosDynamicAddFails, docsQosDynamicChanges, docsQosDynamicChangeFails, docsQosDynamicDeletes, docsQosDynamicDeleteFails, Expires April 2001 [Page 69]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 docsQosDCCReqs, docsQosDCCRsps, docsQosDCCAcks, docsQosDCCs, docsQosDCCFails, docsQosPHSField, docsQosPHSMask, docsQosPHSSize, docsQosPHSVerify, docsQosPHSIndex } STATUS current DESCRIPTION "Group of objects implemented in both Cable Modems and Cable Modem Termination Systems." ::= { docsQosGroups 1 } docsQosParamSetGroup OBJECT-GROUP OBJECTS { docsQosParamSetServiceClassName, docsQosParamSetPriority, docsQosParamSetMaxTrafficRate, docsQosParamSetMaxTrafficBurst, docsQosParamSetMinReservedRate, docsQosParamSetMinReservedPkt, docsQosParamSetActiveTimeout, docsQosParamSetAdmittedTimeout, docsQosParamSetMaxConcatBurst, docsQosParamSetSchedulingType, docsQosParamSetNomPollInterval, docsQosParamSetTolPollJitter, docsQosParamSetUnsolicitGrantSize, docsQosParamSetNomGrantInterval, docsQosParamSetTolGrantJitter, docsQosParamSetGrantsPerInterval, docsQosParamSetTosAndMask, docsQosParamSetTosOrMask, docsQosParamSetMaxLatency, docsQosParamSetRequestPolicyOct, docsQosParamSetBitMap } STATUS current DESCRIPTION "Group of objects implemenent in both Cable Modems and Cable Modem Termination Systems for QOS parameter sets." ::= { docsQosGroups 2 } docsQosCmtsGroup OBJECT-GROUP OBJECTS { Expires April 2001 [Page 70]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 docsQosUpstreamFragments, docsQosUpstreamFragDiscards, docsQosUpstreamConcatBursts, docsQosServiceFlowLogIfIndex, docsQosServiceFlowLogSFID, docsQosServiceFlowLogCmMac, docsQosServiceFlowLogPkts, docsQosServiceFlowLogOctets, docsQosServiceFlowLogTimeDeleted, docsQosServiceFlowLogTimeCreated, docsQosServiceFlowLogTimeActive, docsQosServiceFlowLogDirection, docsQosServiceFlowLogPrimary, docsQosServiceFlowLogServiceClassName, docsQosServiceFlowLogPolicedDropPkts, docsQosServiceFlowLogPolicedDelayPkts, docsQosServiceFlowLogControl, docsQosCmtsIfIndex -- docsQosCmtsMacToSrvFlowTable required } STATUS current DESCRIPTION "Mandatory group of objects implemented only in the CMTS." ::= { docsQosGroups 3 } docsQosSrvClassPolicyGroup OBJECT-GROUP OBJECTS { docsQosServiceClassPolicyName, docsQosServiceClassPolicyRulePriority, docsQosServiceClassPolicyStatus } STATUS current DESCRIPTION "Group of objects implemented in both Cable Modems and Cable Modem Termination Systems when supporting policy based service flows." ::= { docsQosGroups 4 } docsQosServiceClassGroup OBJECT-GROUP OBJECTS { docsQosServiceClassStatus, docsQosServiceClassPriority, docsQosServiceClassMaxTrafficRate, docsQosServiceClassMaxTrafficBurst, docsQosServiceClassMinReservedRate, docsQosServiceClassMinReservedPkt, docsQosServiceClassMaxConcatBurst, docsQosServiceClassNomPollInterval, docsQosServiceClassTolPollJitter, Expires April 2001 [Page 71]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 docsQosServiceClassUnsolicitGrantSize, docsQosServiceClassNomGrantInterval, docsQosServiceClassTolGrantJitter, docsQosServiceClassGrantsPerInterval, docsQosServiceClassMaxLatency, docsQosServiceClassActiveTimeout, docsQosServiceClassAdmittedTimeout, docsQosServiceClassSchedulingType, docsQosServiceClassRequestPolicy, docsQosServiceClassTosAndMask, docsQosServiceClassTosOrMask, docsQosServiceClassDirection } STATUS current DESCRIPTION "The docsQosServiceClassTable objects. If a CMTS implements expansion of Service Class Names in a QOS Parameter Set, this group is mandatory on the CMTS. If the CMTS does not support Service Class Names, this group may be unimplemented in the CMTS. This group is not implemented on the CM. " ::= { docsQosGroups 5 } END Expires April 2001 [Page 72]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 5. References [1] Harrington, D., Presuhn, R., and B. Wijnen, "An Architecture for Describing SNMP Management Frameworks", RFC 2271, Cabletron Systems, Inc., BMC Software, Inc., IBM T. J. Watson Research, January 1998 [2] Rose, M., and K. McCloghrie, "Structure and Identification of Management Information for TCP/IP-based Internets", RFC 1155, Performance Systems International, Hughes LAN Systems, May 1990 [3] Rose, M., and K. McCloghrie, "Concise MIB Definitions", RFC 1212, Performance Systems International, Hughes LAN Systems, March 1991 [4] M. Rose, "A Convention for Defining Traps for use with the SNMP", RFC 1215, Performance Systems International, March 1991 [5] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Structure of Management Information for Version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1902, SNMP Research,Inc., Cisco Systems, Inc., Dover Beach Consulting, Inc., International Network Services, January 1996. [6] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Textual Conventions for Version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1903, SNMP Research, Inc., Cisco Systems, Inc., Dover Beach Consulting, Inc., International Network Services, January 1996. [7] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Conformance Statements for Version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1904, SNMP Research, Inc., Cisco Systems, Inc., Dover Beach Consulting, Inc., International Network Services, January 1996. [8] Case, J., Fedor, M., Schoffstall, M., and J. Davin, "Simple Network Management Protocol", RFC 1157, SNMP Research, Performance Systems International, Performance Systems International, MIT Laboratory for Computer Science, May 1990. [9] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Introduction to Community-based SNMPv2", RFC 1901, SNMP Research, Inc., Cisco Systems, Inc., Dover Beach Consulting, Inc., International Network Services, January 1996. [10] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Transport Mappings for Version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1906, SNMP Research, Inc., Cisco Systems, Inc., Dover Beach Consulting, Inc., International Network Services, January 1996. Expires April 2001 [Page 73]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 [11] Case, J., Harrington D., Presuhn R., and B. Wijnen, "Message Processing and Dispatching for the Simple Network Management Protocol (SNMP)", RFC 2272, SNMP Research, Inc., Cabletron Systems, Inc., BMC Software, Inc., IBM T. J. Watson Research, January 1998. [12] Blumenthal, U., and B. Wijnen, "User-based Security Model (USM) for version 3 of the Simple Network Management Protocol (SNMPv3)", RFC 2274, IBM T. J. Watson Research, January 1998. [13] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Protocol Operations for Version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1905, SNMP Research, Inc., Cisco Systems, Inc., Dover Beach Consulting, Inc., International Network Services, January 1996. [14] Levi, D., Meyer, P., and B. Stewart, "SNMPv3 Applications", RFC 2273, SNMP Research, Inc., Secure Computing Corporation, Cisco Systems, January 1998 [15] Wijnen, B., Presuhn, R., and K. McCloghrie, "View-based Access Control Model (VACM) for the Simple Network Management Protocol (SNMP)", RFC 2275, IBM T. J. Watson Research, BMC Software, Inc., Cisco Systems, Inc., January 1998 [16] " Data-Over-Cable Service Interface Specifications: Cable Modem Radio Frequency Interface Specification SP-RFIv1_1-I05-000714", DOCSIS, March 1999, http://www.cablemodem.com. [17] L. Steinberg, "Techniques for Managing Asynchronously Generated Alerts", RFC 1224, May 1991. [18] "Data-Over-Cable Service Interface Specifications: Operations Support System Interface Specification RF Interface SP-OSSI-RF- I02-980410", DOCSIS, April 1998, http://www.cablemodem.com/public/pubtechspec/ossi/sp-ossi.PDF. [19] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", RFC2119, Harvard University, March 1997 [20] "Data-Over-Cable Service Interface Specifications: Baseline Privacy Interface Specification SP-BPI-I01-970922", DOCSIS, September 1977, http://www.cablemodem.com/public/pubtechspec/ss/SP-BPI-I01- 970922.pdf [21] "Cable Device Management Information Base for DOCSIS compliant Cable Modems and Cable Modem Termination Systems", RFC2669 [22] "Radio Frequency (RF) Interface Management Information Base for MCNS/DOCSIS compliant RF interfaces", RFC 2670 Expires April 2001 [Page 74]
INTERNET-DRAFT<draft-ietf-ipcdn-qos-mib-04.txt> October 2000 6. Authors' Addresses Michael Patrick Motorola Broadband Communications Sector 20 Cabot Blvd., MS M4-30 Mansfield, MA 02048 Phone: (508) 261-5707 Email: michael.patrick@motorola.com Expires April 2001 [Page 75]
