Network Working Group T. Dietz, Ed.
Internet-Draft NEC Europe Ltd.
Intended status: Standards Track B. Claise
Expires: May 3, 2012 Cisco Systems, Inc.
J. Quittek
NEC Europe Ltd.
October 31, 2011
Definitions of Managed Objects for Packet Sampling
<draft-ietf-ipfix-psamp-mib-04.txt>
Abstract
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in the Internet community.
In particular, it describes extensions to the IPFIX SELECTOR MIB
module [I-D.dkcm-ipfix-rfc5815bis]. For IPFIX implementations that
use packet Sampling (PSAMP) techniques as described in [RFC5475],
this memo defines the PSAMP MIB module containing managed objects for
providing information on applied packet selection functions and their
parameters.
Status of this Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on May 3, 2012.
Copyright Notice
Copyright (c) 2011 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
Dietz, et al. draft-ietf-ipfix-psamp-mib-04.txt [Page 1]
Internet-Draft PSAMP MIB October 2011
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. The Internet-Standard Management Framework . . . . . . . . . . 3
2. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3
3. PSAMP Documents Overview . . . . . . . . . . . . . . . . . . . 4
4. Related IPFIX Documents . . . . . . . . . . . . . . . . . . . 4
5. Structure of the PSAMP MIB module . . . . . . . . . . . . . . 4
5.1. Textual Conventions . . . . . . . . . . . . . . . . . . . 5
5.2. Packet Selection Functions . . . . . . . . . . . . . . . . 6
5.2.1. Systematic Count-based Sampling . . . . . . . . . . . 6
5.2.2. Systematic Time-based Sampling . . . . . . . . . . . . 7
5.2.3. Random n-out-of-N Sampling . . . . . . . . . . . . . . 7
5.2.4. Uniform Probabilistic Sampling . . . . . . . . . . . . 7
5.2.5. Property Match Filtering . . . . . . . . . . . . . . . 8
5.2.6. Hash-based Filtering . . . . . . . . . . . . . . . . . 8
6. Definitions . . . . . . . . . . . . . . . . . . . . . . . . . 8
7. Security Considerations . . . . . . . . . . . . . . . . . . . 25
8. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 25
9. Acknowledgment . . . . . . . . . . . . . . . . . . . . . . . . 26
10. References . . . . . . . . . . . . . . . . . . . . . . . . . . 26
10.1. Normative References . . . . . . . . . . . . . . . . . . . 26
10.2. Informative References . . . . . . . . . . . . . . . . . . 27
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 27
Dietz, et al. draft-ietf-ipfix-psamp-mib-04.txt [Page 2]
Internet-Draft PSAMP MIB October 2011
1. The Internet-Standard Management Framework
For a detailed overview of the documents that describe the current
Internet-Standard Management Framework, please refer to section 7 of
RFC 3410 [RFC3410].
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. MIB objects are generally
accessed through the Simple Network Management Protocol (SNMP).
Objects in the MIB are defined using the mechanisms defined in the
Structure of Management Information (SMI). This memo specifies MIB
modules that is compliant to the SMIv2, which is described in STD 58,
RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58,RFC 2580
[RFC2580].
2. Introduction
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in RFC
2119 [RFC2119].
This document is a product of the IP Flow Information eXport (IPFIX)
working group. Work on this document was started in the Packet
Sampling (PSAMP) Working Group (WG) and moved to the IPFIX WG when
the PSAMP WG was concluded.
Its purpose is to define managed objects for monitoring PSAMP Devices
performing packet selection by Sampling and Filtering as described in
[RFC5475].
It is assumed that packet Sampling is performed according to the
framework defined in [RFC5474].
Managed objects in the PSAMP MIB module are defined as an extension
of the IPFIX MIB and IPFIX SELECTOR MIB modules
[I-D.dkcm-ipfix-rfc5815bis]. Since the IPFIX MIB module is only for
monitoring the same holds true for the PSAMP MIB module defined in
this document. The definition of objects is in line with the PSAMP
information model [RFC5477].
Section 3 gives an overview of the PSAMP documents, while section 4
refers to the related IPFIX documents. Section 5 describes the
structure of the PSAMP MIB module and section 6 contains the formal
definition. Security issues are discussed in section 7.
Dietz, et al. draft-ietf-ipfix-psamp-mib-04.txt [Page 3]
Internet-Draft PSAMP MIB October 2011
3. PSAMP Documents Overview
[RFC5474]: "A Framework for Packet Selection and Reporting" describes
the PSAMP framework for network elements to select subsets of packets
by statistical and other methods, and to export a stream of reports
on the selected packets to a Collector.
[RFC5475]: "Sampling and Filtering Techniques for IP Packet
Selection" describes the set of packet selection techniques supported
by PSAMP.
[RFC5476]: "Packet Sampling (PSAMP) Protocol Specifications"
specifies the export of packet information from a PSAMP Exporting
Process to a PSAMP Collecting Process.
[RFC5477]: "Information Model for Packet Sampling Exports" defines an
information and data model for PSAMP.
This document: "Definitions of Managed Objects for Packet Sampling"
describes the PSAMP Management Information Base.
4. Related IPFIX Documents
The IPFIX protocol provides network administrators with access to IP
Flow information.
[RFC5101]: The protocol document "Specification of the IP Flow
Information Export (IPFIX) Protocol for the Exchange of IP Traffic
Flow Information" specifies how IPFIX Data Records and Templates are
carried via a congestion-aware transport protocol from IPFIX
Exporting Processes to IPFIX Collecting Processes. It also specifies
the data types used in the PSAMP MIB module and their encoding.
[I-D.dkcm-ipfix-rfc5815bis]: The IPFIX MIB "Definitions of Managed
Objects for IP Flow Information Export" is the basis for this
document because it extends the IPFIX SELECTOR MIB defined there.
5. Structure of the PSAMP MIB module
The IPFIX MIB module defined in [I-D.dkcm-ipfix-rfc5815bis] has the
concept of a packet Selection Process containing a set of Selector
function instances. Selection Processes and functions are referenced
in the ipfixSelectionProcessTable of the IPFIX MIB module. The
ipfixSelectionProcessTable identifies an instance of a Selector
function by an OID. The OID points to an object that describes the
Selector function. For simple Selector functions without parameters,
Dietz, et al. draft-ietf-ipfix-psamp-mib-04.txt [Page 4]
Internet-Draft PSAMP MIB October 2011
the OID refers to an object which contains only one additional object
indicating the current availability of the function. For functions
which have one or more parameters the object has a subtree that in
addition to an availability object contains a table with a conceptual
column for each parameter. Entries (conceptual rows) in this table
represent different combinations of parameter values for instances of
the Selector function.
The object ipfixSelectorFunctions in the IPFIX SELECTOR MIB module
serves as the root for objects that describe instances of packet
Selector functions. The IPFIX SELECTOR MIB is a very small module
which is defined in [I-D.dkcm-ipfix-rfc5815bis]. The top level OIDs
of the parameter trees located beneath ipfixSelectorFunctions are
maintained by IANA. In the IPFIX SELECTOR MIB module as defined by
[I-D.dkcm-ipfix-rfc5815bis] the object ipfixSelectorFunctions
contains just a single trivial packet Selector function called
ipfixFuncSelectAll that selects every packet and has no parameter:
ipfixSelectorMIB
+- ipfixSelectorObjects(1)
+- ipfixSelectorFunctions(1)
+- ipfixFuncSelectAll(1)
+- ipfixFuncSelectAllAvail(1)
The PSAMP MIB module defined in this document registers additional
toplevel OIDs for the parameter subtrees of its Selector functions in
the IPFIX-SELECTOR-MIB Function subregistry according to the
procedures defined in [I-D.dkcm-ipfix-rfc5815bis]. It introduces six
new subtrees beneath ipfixSelectorFunctions. Each of them describes
a packet Selector function with one or more parameters. Naming and
ordering of objects is fully in line with the guidelines given in
section 6.1 of [I-D.dkcm-ipfix-rfc5815bis]. All functions and their
parameters are already listed in the overview of functions given by
the table in section 8.2.1 of [RFC5477].
5.1. Textual Conventions
The PSAMP MIB module imports two textual conventions which define
data types used in this MIB from other MIB modules. The Unsigned64TC
data type is imported from the APPLICATION MIB [RFC2564] and the
Float64TC data type is imported from the FLOAT-TC-MIB [RFC6340].
Those data types are defined according to [RFC5101]. Those data
types are not an integral part of [RFC2578] but are needed to define
objects in this MIB module that conform to the Information Elements
defined for those objects in [RFC5477].
The Unsigned64TC textual convention describes an unsigned integer of
64 bits. It is imported from the APPLICATION MIB. The Float64TC
Dietz, et al. draft-ietf-ipfix-psamp-mib-04.txt [Page 5]
Internet-Draft PSAMP MIB October 2011
textual convention describes the format that is used for 64 bit
floating point numbers.
5.2. Packet Selection Functions
In general, different packet Selector functions have different
parameters. The PSAMP MIB module contains six objects with subtrees
that provide information on parameters of function instances of
different Selector functions. All objects are named and structured
according to section 8.2.1 of [RFC5477]:
ipfixSelectorFunctions(1)
+-- psampSampCountBased(2)
+- -psampSampTimeBased(3)
+-- psampSampRandOutOfN(4)
+-- psampSampUniProb(5)
+-- psampFiltPropMatch(6)
+-- psampFiltHash(7)
Indexing of these functions in the PSAMP MIB module starts with index
(2). The function ipfixFuncSelectAll with index (1) is already
defined in the IPFIX SELECTOR MIB module as shown above.
The object tree for each of these functions is described below.
Semantics of all functions and their parameters are described in
detail in [RFC5475]. More information on the Selector Reports can
also be found in section 6.5.2 of [RFC5476].
5.2.1. Systematic Count-based Sampling
The first Selector function is systematic count-based Sampling. Its
availability is indicated by object psampSampCountBasedAvail. The
function has two parameters: psampSampCountBasedInterval and
psampSampCountBasedSpace. Different combination of values of these
parameters for different instances of the Selector function are
represented by different conceptual rows in table
psampSampCountBasedParamSetEntry:
psampSampCountBased(2)
+-- psampSampCountBasedAvail(1)
+-- psampSampCountBasedParamSetTable(2)
+-- psampSampCountBasedParamSetEntry(1) [psampSampCountBasedIndex]
+-- psampSampCountBasedIndex(1)
+-- psampSampCountBasedInterval(2)
+-- psampSampCountBasedSpace(3)
Dietz, et al. draft-ietf-ipfix-psamp-mib-04.txt [Page 6]
Internet-Draft PSAMP MIB October 2011
5.2.2. Systematic Time-based Sampling
The second Selector function is systematic time-based Sampling. The
structure of the sub-tree for this function is similar to the
psampSampCountBased sub-tree. Parameters are
psampSampTimeBasedInterval and psampSampTimeBasedSpace. They appear
to be the same as for count based Sampling, but their data types are
different because they indicate time values instead of numbers of
packets:
psampSampTimeBased(3)
+-- psampSampTimeBasedAvail(1)
+-- psampSampTimeBasedParamSetTable(2)
+-- psampSampTimeBasedParamSetEntry(1) [psampSampTimeBasedIndex]
+-- psampSampTimeBasedIndex(1)
+-- psampSampTimeBasedInterval(2)
+-- psampSampTimeBasedSpace(3)
5.2.3. Random n-out-of-N Sampling
The third Selector function is random n-out-of-N Sampling.
Parameters are psampSampRandOutOfNSize and
psampSampRandOutOfNPopulation:
psampSampRandOutOfN(4)
+-- psampSampRandOutOfNAvail(1)
+-- psampSampRandOutOfNParamSetTable(2)
+-- psampSampRandOutOfNParamSetEntry(1) [psampSampRandOutOfNIndex]
+-- psampSampRandOutOfNIndex(1)
+-- psampSampRandOutOfNSize(2)
+-- psampSampRandOutOfNPopulation(3)
5.2.4. Uniform Probabilistic Sampling
The fourth Selector function is uniform probabilistic Sampling. It
has just a single parameter called psampSampUniProbProbability:
psampSampUniProb(5)
+-- psampSampUniProbAvail(1)
+-- psampSampUniProbParamSetTable(2)
+-- psampSampUniProbParamSetEntry(1) [psampSampUniProbIndex]
+-- psampSampUniProbIndex(1)
+-- psampSampUniProbProbability(2)
Dietz, et al. draft-ietf-ipfix-psamp-mib-04.txt [Page 7]
Internet-Draft PSAMP MIB October 2011
5.2.5. Property Match Filtering
The fifth Selector function is property match Filtering. For this
Selector function there is a broad variety of possible parameters
that could be used. But as stated in section 8.2.1 of [RFC5477]
there are no agreed parameters specified and the sub-tree for this
function only contains an object indicating the availability of this
function. Parameters cannot be retrieved via the PSAMP MIB module:
psampFiltPropMatch(6)
+-- psampFiltPropMatchAvail(1)
5.2.6. Hash-based Filtering
The sixth Selector function is hash-based Filtering. The object
psampFiltHashFunction is an enumeration that specifies the kind of
hash function that is applied. These hash function have quite a
number of parameters and the actual number may vary with the choice
of the hash function applied. The common parameter set for all hash-
based Filtering functions contains 7 parameters:
psampFiltHashInitializerValue, psampFiltHashIpPayloadOffset,
psampFiltHashIpPayloadSize, psampFiltHashSelectedRangeMin,
psampFiltHashSelectedRangeMax, psampFiltHashOutputRangeMin, and
psampFiltHashOutputRangeMax.
psampFiltHash(7)
+-- psampFiltHashAvail(1)
+-- psampFiltHashCapabilities(2)
+-- psampFiltHashParamSetTable(3)
+-- psampFiltHashParamSetEntry(1) [psampFiltHashIndex]
+-- psampFiltHashIndex(1)
+-- psampFiltHashFunction(2)
+-- psampFiltHashInitializerValue(3)
+-- psampFiltHashIpPayloadOffset(4)
+-- psampFiltHashIpPayloadSize(5)
+-- psampFiltHashSelectedRangeMin(6)
+-- psampFiltHashSelectedRangeMax(7)
+-- psampFiltHashOutputRangeMin(8)
+-- psampFiltHashOutputRangeMax(9)
Further parameters depend on the applied hash function and are not
specified within the PSAMP MIB module.
6. Definitions
PSAMP-MIB DEFINITIONS ::= BEGIN
Dietz, et al. draft-ietf-ipfix-psamp-mib-04.txt [Page 8]
Internet-Draft PSAMP MIB October 2011
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, Integer32, Unsigned32, mib-2
FROM SNMPv2-SMI -- RFC2578
TruthValue
FROM SNMPv2-TC -- RFC2579
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF -- RFC2580
Unsigned64TC
FROM APPLICATION-MIB -- RFC2564
Float64TC
FROM FLOAT-TC-MIB -- RFC6340
ipfixSelectorFunctions
FROM IPFIX-SELECTOR-MIB;
psampMIB MODULE-IDENTITY
LAST-UPDATED "201110311200Z" -- 31 October 2011
ORGANIZATION "IETF IPFIX Working Group"
CONTACT-INFO
"WG charter:
http://www.ietf.org/html.charters/ipfix-charter.html
Mailing Lists:
General Discussion: ipfix@ietf.org
To Subscribe: http://www1.ietf.org/mailman/listinfo/ipfix
Archive:
http://www1.ietf.org/mail-archive/web/ipfix/current/index.html
Editor:
Thomas Dietz
NEC Europe Ltd.
NEC Laboratories Europe
Network Research Division
Kurfuersten-Anlage 36
69115 Heidelberg
Germany
Phone: +49 6221 4342-128
Email: Thomas.Dietz@neclab.eu
Benoit Claise
Cisco Systems, Inc.
De Kleetlaan 6a b1
Degem 1831
Belgium
Phone: +32 2 704 5622
Email: bclaise@cisco.com
Juergen Quittek
NEC Europe Ltd.
Dietz, et al. draft-ietf-ipfix-psamp-mib-04.txt [Page 9]
Internet-Draft PSAMP MIB October 2011
NEC Laboratories Europe
Network Research Division
Kurfuersten-Anlage 36
69115 Heidelberg
Germany
Phone: +49 6221 4342-115
Email: quittek@neclab.eu"
DESCRIPTION
"The PSAMP MIB defines managed objects for packet sampling
and filtering.
These objects provide information about managed nodes
supporting packet sampling, including packet sampling
capabilities, configuration and statistics.
The PSAMP MIB module registers additional toplevel OIDs for
the parameter subtrees of its Selector functions in the
IPFIX-SELECTOR-MIB Function subregistry according to the
procedures defined in RFC 5815bis.
-- RFC Ed.: replace RFC 5815bis above with the actual RFC number
-- once assigned and remove this notice
Copyright (c) 2011 IETF Trust and the persons identified as
the document authors. All rights reserved. This version
of this MIB module is part of RFC yyyy; see the RFC itself
for full legal notices"
-- RFC Ed.: replace yyyy with actual RFC number & remove this notice
-- Revision history
REVISION "201110311200Z" -- 31 October 2011
DESCRIPTION
"Initial version, published as RFC yyyy."
-- RFC Ed.: replace yyyy with actual RFC number & remove this notice
::= { mib-2 xxx }
-- RFC Ed.: replace xxx which is to be assigned by IANA & remove
-- this notice.
-- Top level structure of the MIB
psampObjects OBJECT IDENTIFIER ::= { psampMIB 1 }
psampConformance OBJECT IDENTIFIER ::= { psampMIB 2 }
--==================================================================
-- Packet selection sampling methods group of objects
--==================================================================
--==================================================================
--* Method 1: Systematic count-based Sampling
Dietz, et al. draft-ietf-ipfix-psamp-mib-04.txt [Page 10]
Internet-Draft PSAMP MIB October 2011
--==================================================================
-- Reference: RFC5475, Section 5.1, RFC5476 Section 6.5.2.1 and
-- RFC5477, Section 8.2
psampSampCountBased OBJECT IDENTIFIER
::= { ipfixSelectorFunctions 2 }
psampSampCountBasedAvail OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the availability of systematic
count-based sampling at the managed node.
A Selector may be unavailable if it is implemented but
currently disabled due to e.g., administrative reasons, lack
of resources or similar."
DEFVAL { false }
::= { psampSampCountBased 1 }
-- Parameter Set Table +++++++++++++++++++++++++++++++++++++++++++++
psampSampCountBasedParamSetTable OBJECT-TYPE
SYNTAX SEQUENCE OF
PsampSampCountBasedParamSetEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table lists configurations of systematic count-based
packet sampling. A parameter set describing a
configuration contains two parameters: the sampling
interval length and space."
::= { psampSampCountBased 2 }
psampSampCountBasedParamSetEntry OBJECT-TYPE
SYNTAX PsampSampCountBasedParamSetEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Defines an entry in the psampSampCountBasedParamSetTable."
INDEX { psampSampCountBasedIndex }
::= { psampSampCountBasedParamSetTable 1 }
PsampSampCountBasedParamSetEntry ::=
SEQUENCE {
psampSampCountBasedIndex Integer32,
psampSampCountBasedInterval Unsigned32,
Dietz, et al. draft-ietf-ipfix-psamp-mib-04.txt [Page 11]
Internet-Draft PSAMP MIB October 2011
psampSampCountBasedSpace Unsigned32
}
psampSampCountBasedIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The index of this parameter set in the
psampSampCountBasedParamSetTable. It is used in the
object ipfixSelectionProcessSelectorFunction entries of
the ipfixSelectionProcessTable in the IPFIX-MIB as reference
to this parameter set."
::= { psampSampCountBasedParamSetEntry 1 }
psampSampCountBasedInterval OBJECT-TYPE
SYNTAX Unsigned32
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the number of packets that are
consecutively sampled. A value of 100 means that 100
consecutive packets are sampled."
REFERENCE
"RFC5475, Section 5.1 and RFC5477, Section 8.2"
::= { psampSampCountBasedParamSetEntry 2 }
psampSampCountBasedSpace OBJECT-TYPE
SYNTAX Unsigned32
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the number of packets between two
psampSampCountBasedInterval's. A value of 100 means that
the next interval starts 100 packets (which are not sampled)
after the current psampSampCountBasedInterval is over."
REFERENCE
"RFC5475, Section 5.1 and RFC5477, Section 8.2"
::= { psampSampCountBasedParamSetEntry 3 }
--==================================================================
--* Method 2: Systematic time-based Sampling
--==================================================================
-- Reference: RFC5475, Section 5.1, RFC5476 Section 6.5.2.2 and
-- RFC5477, Section 8.2
Dietz, et al. draft-ietf-ipfix-psamp-mib-04.txt [Page 12]
Internet-Draft PSAMP MIB October 2011
psampSampTimeBased OBJECT IDENTIFIER
::= { ipfixSelectorFunctions 3 }
psampSampTimeBasedAvail OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the availability of systematic
time-based sampling at the managed node.
A Selector may be unavailable if it is implemented but
currently disabled due to e.g., administrative reasons, lack
of resources or similar."
DEFVAL { false }
::= { psampSampTimeBased 1 }
-- Parameter Set Table +++++++++++++++++++++++++++++++++++++++++++++
psampSampTimeBasedParamSetTable OBJECT-TYPE
SYNTAX SEQUENCE OF
PsampSampTimeBasedParamSetEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table lists configurations of systematic time-based
packet sampling. A parameter set describing a configuration
contains two parameters: the sampling interval length and
the space."
::= { psampSampTimeBased 2 }
psampSampTimeBasedParamSetEntry OBJECT-TYPE
SYNTAX PsampSampTimeBasedParamSetEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Defines an entry in the psampSampTimeBasedParamSetTable."
INDEX { psampSampTimeBasedIndex }
::= { psampSampTimeBasedParamSetTable 1 }
PsampSampTimeBasedParamSetEntry ::=
SEQUENCE {
psampSampTimeBasedIndex Integer32,
psampSampTimeBasedInterval Unsigned32,
psampSampTimeBasedSpace Unsigned32
}
psampSampTimeBasedIndex OBJECT-TYPE
Dietz, et al. draft-ietf-ipfix-psamp-mib-04.txt [Page 13]
Internet-Draft PSAMP MIB October 2011
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The index of this parameter set in the
psampSampTimeBasedParamSetTable. It is used in the
object ipfixSelectionProcessSelectorFunction entries of
the ipfixSelectionProcessTable in the IPFIX-MIB as reference
to this parameter set."
::= { psampSampTimeBasedParamSetEntry 1 }
psampSampTimeBasedInterval OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the time interval in microseconds
during which all arriving packets are sampled."
REFERENCE
"RFC5475, Section 5.1 and RFC5477, Section 8.2"
::= { psampSampTimeBasedParamSetEntry 2 }
psampSampTimeBasedSpace OBJECT-TYPE
SYNTAX Unsigned32
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the time interval in microseconds
between two psampSampTimeBasedInterval's. A value of 100
means that the next interval starts 100 microseconds (during
which no packets are sampled) after the current
psampSampTimeBasedInterval is over."
REFERENCE
"RFC5475, Section 5.1 and RFC5477, Section 8.2"
::= { psampSampTimeBasedParamSetEntry 3 }
--==================================================================
--* Method 3: Random n-out-of-N Sampling
--==================================================================
-- Reference: RFC5475, Section 5.2.1, RFC5476 Section 6.5.2.3 and
-- RFC5477, Section 8.2
psampSampRandOutOfN OBJECT IDENTIFIER
::= { ipfixSelectorFunctions 4 }
psampSampRandOutOfNAvail OBJECT-TYPE
Dietz, et al. draft-ietf-ipfix-psamp-mib-04.txt [Page 14]
Internet-Draft PSAMP MIB October 2011
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the availability of random n-out-of-N
sampling at the managed node.
A Selector may be unavailable if it is implemented but
currently disabled due to e.g., administrative reasons, lack
of resources or similar."
DEFVAL { false }
::= { psampSampRandOutOfN 1 }
-- Parameter Set Table +++++++++++++++++++++++++++++++++++++++++++++
psampSampRandOutOfNParamSetTable OBJECT-TYPE
SYNTAX SEQUENCE OF
PsampSampRandOutOfNParamSetEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table lists configurations of random n-out-of-N
sampling. A parameter set describing a configuration
contains two parameters, the sampling size and the
parent population."
::= { psampSampRandOutOfN 2 }
psampSampRandOutOfNParamSetEntry OBJECT-TYPE
SYNTAX PsampSampRandOutOfNParamSetEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Defines an entry in the psampSampRandOutOfNParamSetTable."
INDEX { psampSampRandOutOfNIndex }
::= { psampSampRandOutOfNParamSetTable 1 }
PsampSampRandOutOfNParamSetEntry ::=
SEQUENCE {
psampSampRandOutOfNIndex Integer32,
psampSampRandOutOfNSize Unsigned32,
psampSampRandOutOfNPopulation Unsigned32
}
psampSampRandOutOfNIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
Dietz, et al. draft-ietf-ipfix-psamp-mib-04.txt [Page 15]
Internet-Draft PSAMP MIB October 2011
"The index of this parameter set in the
psampSampRandOutOfNParamSetTable. It is used in the
object ipfixSelectionProcessSelectorFunction entries of
the ipfixSelectionProcessTable in the IPFIX-MIB as reference
to this parameter set."
::= { psampSampRandOutOfNParamSetEntry 1 }
psampSampRandOutOfNSize OBJECT-TYPE
SYNTAX Unsigned32
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the number of elements taken from the
parent Population specified in
psampSampRandOutOfNPopulation."
REFERENCE
"RFC5475, Section 5.2.1 and RFC5477, Section 8.2"
::= { psampSampRandOutOfNParamSetEntry 2 }
psampSampRandOutOfNPopulation OBJECT-TYPE
SYNTAX Unsigned32
UNITS "packets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the number of elements in the parent
Population."
REFERENCE
"RFC5475, Section 5.2.1 and RFC5477, Section 8.2"
::= { psampSampRandOutOfNParamSetEntry 3 }
--==================================================================
--* Method 4: Uniform probabilistic Sampling
--==================================================================
-- Reference: RFC5475, Section 5.2.2, RFC5476 Section 6.5.2.4 and
-- RFC5477, Section 8.2
psampSampUniProb OBJECT IDENTIFIER ::= { ipfixSelectorFunctions 5 }
psampSampUniProbAvail OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the availability of random uniform
probabilistic sampling at the managed node.
Dietz, et al. draft-ietf-ipfix-psamp-mib-04.txt [Page 16]
Internet-Draft PSAMP MIB October 2011
A Selector may be unavailable if it is implemented but
currently disabled due to e.g., administrative reasons, lack
of resources or similar."
DEFVAL { false }
::= { psampSampUniProb 1 }
-- Parameter Set Table +++++++++++++++++++++++++++++++++++++++++++++
-- Reference: RFC5475, Section 5.2.2.1 and RFC5477, Section 8.2
psampSampUniProbParamSetTable OBJECT-TYPE
SYNTAX SEQUENCE OF
PsampSampUniProbParamSetEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table lists configurations of random probabilistic
sampling. A parameter set describing a configuration
contains a single parameter only: the sampling probability."
::= { psampSampUniProb 2 }
psampSampUniProbParamSetEntry OBJECT-TYPE
SYNTAX PsampSampUniProbParamSetEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Defines an entry in the psampSampUniProbParamSetTable."
INDEX { psampSampUniProbIndex }
::= { psampSampUniProbParamSetTable 1 }
PsampSampUniProbParamSetEntry ::=
SEQUENCE {
psampSampUniProbIndex Integer32,
psampSampUniProbProbability Float64TC
}
psampSampUniProbIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The index of this parameter set in the
psampSampUniProbParamSetTable. It is used in the
object ipfixSelectionProcessSelectorFunction entries of
the ipfixSelectionProcessTable in the IPFIX-MIB as reference
to this parameter set."
::= { psampSampUniProbParamSetEntry 1 }
psampSampUniProbProbability OBJECT-TYPE
Dietz, et al. draft-ietf-ipfix-psamp-mib-04.txt [Page 17]
Internet-Draft PSAMP MIB October 2011
SYNTAX Float64TC
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the probability that a packet is
sampled, expressed as a value between 0 and 1. The
probability is equal for every packet. A value of 0 means
no packet is sampled since the probability is 0. A value
of 1 means all packets are sampled since the
probability is 1. NaN (not a number) and infinity MUST NOT
be used."
REFERENCE
"RFC5475, Section 5.2.2.1 and RFC5477, Section 8.2"
::= { psampSampUniProbParamSetEntry 2 }
--==================================================================
-- Packet selection filtering methods group of objects
--==================================================================
--==================================================================
--* Method 5: Property Match filtering
--==================================================================
-- Reserves Method 5 (see RFC5475, Section 6.1, RFC5476
-- Section 6.5.2.5 and RFC5477)
psampFiltPropMatch OBJECT IDENTIFIER
::= { ipfixSelectorFunctions 6 }
psampFiltPropMatchAvail OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the availability of property match
filtering at the managed node.
A Selector may be unavailable if it is implemented but
currently disabled due to e.g., administrative reasons, lack
of resources or similar."
DEFVAL { false }
::= { psampFiltPropMatch 1 }
--==================================================================
--* Method 6: Hash filtering
--==================================================================
-- Reference: RFC5475, Section 6.2, RFC5476 Section 6.5.2.6 and
-- RFC5477, Section 8.3
Dietz, et al. draft-ietf-ipfix-psamp-mib-04.txt [Page 18]
Internet-Draft PSAMP MIB October 2011
psampFiltHash OBJECT IDENTIFIER ::= { ipfixSelectorFunctions 7 }
psampFiltHashAvail OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the availability of hash filtering
at the managed node.
A Selector may be unavailable if it is implemented but
currently disabled due to e.g., administrative reasons, lack
of resources or similar."
DEFVAL { false }
::= { psampFiltHash 1 }
psampFiltHashCapabilities OBJECT IDENTIFIER
::= { psampFiltHash 2 }
-- Parameter Set Table +++++++++++++++++++++++++++++++++++++++++++++
-- Reference: RFC5475, Sections 6.2, 3.8, and 7.1
psampFiltHashParamSetTable OBJECT-TYPE
SYNTAX SEQUENCE OF
PsampFiltHashParamSetEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table lists configurations of hash filtering. A
parameter set describing a configuration contains eight
parameters describing the hash function."
::= { psampFiltHash 3 }
psampFiltHashParamSetEntry OBJECT-TYPE
SYNTAX PsampFiltHashParamSetEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Defines an entry in the psampFiltHashParamSetTable."
INDEX { psampFiltHashIndex }
::= { psampFiltHashParamSetTable 1 }
PsampFiltHashParamSetEntry ::=
SEQUENCE {
psampFiltHashIndex Integer32,
psampFiltHashFunction INTEGER,
psampFiltHashInitializerValue Unsigned64TC,
psampFiltHashIpPayloadOffset Unsigned64TC,
Dietz, et al. draft-ietf-ipfix-psamp-mib-04.txt [Page 19]
Internet-Draft PSAMP MIB October 2011
psampFiltHashIpPayloadSize Unsigned64TC,
psampFiltHashSelectedRangeMin Unsigned64TC,
psampFiltHashSelectedRangeMax Unsigned64TC,
psampFiltHashOutputRangeMin Unsigned64TC,
psampFiltHashOutputRangeMax Unsigned64TC
}
psampFiltHashIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The index of this parameter set in the
psampFiltHashParamSetTable. It is used in the
object ipfixSelectionProcessSelectorFunction entries of
the ipfixSelectionProcessTable in the IPFIX-MIB as reference
to this parameter set."
::= { psampFiltHashParamSetEntry 1 }
psampFiltHashFunction OBJECT-TYPE
SYNTAX INTEGER {
crc32(1),
ipsx(2),
bob(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Hash Function used by this filter. The PSAMP-MIB
defines the following Hash Functions:
crc32(1): The CRC32 Hash Function as defined in RFC1141.
ipsx(2): The IPSX Hash Function as described in RFC5475
appendix A.1.
bob(3): The BOB Hash Function as described in RFC5475
appendix A.2.
"
REFERENCE
"RFC5475, Section 6.2 and Appendixes A.1 and A.2."
::= { psampFiltHashParamSetEntry 2 }
psampFiltHashInitializerValue OBJECT-TYPE
SYNTAX Unsigned64TC
MAX-ACCESS read-only
STATUS current
DESCRIPTION
Dietz, et al. draft-ietf-ipfix-psamp-mib-04.txt [Page 20]
Internet-Draft PSAMP MIB October 2011
"This object specifies the initializer value to the hash
function."
REFERENCE
"RFC5475, Sections 6.2, 3.8, and 7.1"
::= { psampFiltHashParamSetEntry 3 }
psampFiltHashIpPayloadOffset OBJECT-TYPE
SYNTAX Unsigned64TC
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the IP payload offset used by a
Hash-based Selection Selector."
REFERENCE
"RFC5475, Sections 6.2, 3.8, and 7.1"
::= { psampFiltHashParamSetEntry 4 }
psampFiltHashIpPayloadSize OBJECT-TYPE
SYNTAX Unsigned64TC
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the IP payload size used by a
Hash-based Selection Selector."
REFERENCE
"RFC5475, Sections 6.2, 3.8, and 7.1"
::= { psampFiltHashParamSetEntry 5 }
psampFiltHashSelectedRangeMin OBJECT-TYPE
SYNTAX Unsigned64TC
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the value for the beginning of a hash
function's selected range."
REFERENCE
"RFC5475, Sections 6.2, 3.8, and 7.1"
::= { psampFiltHashParamSetEntry 6 }
psampFiltHashSelectedRangeMax OBJECT-TYPE
SYNTAX Unsigned64TC
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the value for the end of a hash
function's selected range."
REFERENCE
"RFC5475, Sections 6.2, 3.8, and 7.1"
Dietz, et al. draft-ietf-ipfix-psamp-mib-04.txt [Page 21]
Internet-Draft PSAMP MIB October 2011
::= { psampFiltHashParamSetEntry 7 }
psampFiltHashOutputRangeMin OBJECT-TYPE
SYNTAX Unsigned64TC
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the value for the beginning of a hash
function's potential output range."
REFERENCE
"RFC5475, Sections 6.2, 3.8, and 7.1"
::= { psampFiltHashParamSetEntry 8 }
psampFiltHashOutputRangeMax OBJECT-TYPE
SYNTAX Unsigned64TC
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the value for the end of a hash
function's potential output range."
REFERENCE
"RFC5475, Sections 6.2, 3.8, and 7.1"
::= { psampFiltHashParamSetEntry 9 }
--==================================================================
-- Conformance information
--==================================================================
psampCompliances OBJECT IDENTIFIER ::= { psampConformance 1 }
psampGroups OBJECT IDENTIFIER ::= { psampConformance 2 }
--==================================================================
-- Compliance statements
--==================================================================
psampCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The implementation of all objects is optional and depends
on the implementation of the corresponding functionality in
the equipment."
MODULE -- this module
GROUP psampGroupSampCountBased
DESCRIPTION
"These objects must be implemented if systematic
count-based sampling is implemented in the equipment."
GROUP psampGroupSampTimeBased
DESCRIPTION
Dietz, et al. draft-ietf-ipfix-psamp-mib-04.txt [Page 22]
Internet-Draft PSAMP MIB October 2011
"These objects must be implemented if systematic
time-based sampling is implemented in the equipment."
GROUP psampGroupSampRandOutOfN
DESCRIPTION
"These objects must be implemented if random n-out-of-N
sampling is implemented in the equipment."
GROUP psampGroupSampUniProb
DESCRIPTION
"These objects must be implemented if uniform
probabilistic sampling is implemented in the equipment."
GROUP psampGroupFiltPropMatch
DESCRIPTION
"These objects must be implemented if the property match
filtering is implemented in the equipment."
GROUP psampGroupFiltHash
DESCRIPTION
"These objects must be implemented if hash filtering
is implemented in the equipment."
::= { psampCompliances 1 }
--==================================================================
-- MIB groupings
--==================================================================
psampGroupSampCountBased OBJECT-GROUP
OBJECTS {
psampSampCountBasedAvail,
psampSampCountBasedInterval,
psampSampCountBasedSpace
}
STATUS current
DESCRIPTION
"These objects are needed if count based sampling is
implemented."
::= { psampGroups 1 }
psampGroupSampTimeBased OBJECT-GROUP
OBJECTS {
psampSampTimeBasedAvail,
psampSampTimeBasedInterval,
psampSampTimeBasedSpace
}
STATUS current
DESCRIPTION
"These objects are needed if time based sampling is
implemented."
::= { psampGroups 2 }
Dietz, et al. draft-ietf-ipfix-psamp-mib-04.txt [Page 23]
Internet-Draft PSAMP MIB October 2011
psampGroupSampRandOutOfN OBJECT-GROUP
OBJECTS {
psampSampRandOutOfNAvail,
psampSampRandOutOfNSize,
psampSampRandOutOfNPopulation
}
STATUS current
DESCRIPTION
"These objects are needed if random n-out-of-N sampling is
implemented."
::= { psampGroups 3 }
psampGroupSampUniProb OBJECT-GROUP
OBJECTS {
psampSampUniProbAvail,
psampSampUniProbProbability
}
STATUS current
DESCRIPTION
"These objects are needed if uniform probabilistic sampling
is implemented."
::= { psampGroups 4 }
psampGroupFiltPropMatch OBJECT-GROUP
OBJECTS {
psampFiltPropMatchAvail
}
STATUS current
DESCRIPTION
"These objects are needed if property match filtering is
implemented."
::= { psampGroups 5 }
psampGroupFiltHash OBJECT-GROUP
OBJECTS {
psampFiltHashAvail,
psampFiltHashFunction,
psampFiltHashInitializerValue,
psampFiltHashIpPayloadOffset,
psampFiltHashIpPayloadSize,
psampFiltHashSelectedRangeMin,
psampFiltHashSelectedRangeMax,
psampFiltHashOutputRangeMin,
psampFiltHashOutputRangeMax
}
STATUS current
DESCRIPTION
"These objects are needed if hash filtering is implemented."
Dietz, et al. draft-ietf-ipfix-psamp-mib-04.txt [Page 24]
Internet-Draft PSAMP MIB October 2011
::= { psampGroups 6 }
END
7. Security Considerations
There are no management objects defined in this MIB module that have
a MAX-ACCESS clause of read-write and/or read-create. So, if this
MIB module is implemented correctly, then there is no risk that an
intruder can alter or create any management objects of this MIB
module via direct SNMP SET operations.
All tables in this MIB module may be considered sensitive or
vulnerable in some network environments because objects in the tables
may reveal information about the network infrastructure and device
configuration. It is thus important to control even GET and/or
NOTIFY access to these objects and possibly to even encrypt the
values of these objects when sending them over the network via SNMP.
SNMP versions prior to SNMPv3 did not include adequate security.
Even if the network itself is secure (for example by using IPsec),
there is no control as to who on the secure network is allowed to
access and GET/SET (read/change/create/delete) the objects in this
MIB module.
It is RECOMMENDED that implementers consider the security features
provided by the SNMPv3 framework (see [RFC3410], section 8),
including full support for the SNMPv3 cryptographic mechanisms (for
authentication and privacy).
Further, deployment of SNMP versions prior to SNMPv3 is NOT
RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to
enable cryptographic security. It is then a customer/operator
responsibility to ensure that the SNMP entity giving access to an
instance of this MIB module is properly configured to give access to
the objects only to those principals (users) who have legitimate
rights to GET or SET (change/create/delete) them.
8. IANA Considerations
The MIB module in this document uses the following IANA-assigned
OBJECT IDENTIFIER values recorded in the SMI Numbers registry:
Descriptor OBJECT IDENTIFIER value
---------- -----------------------
psampMIB { mib-2 xxx }
Dietz, et al. draft-ietf-ipfix-psamp-mib-04.txt [Page 25]
Internet-Draft PSAMP MIB October 2011
Further on, IANA will register the following toplevel OIDs in the
IPFIX-SELECTOR-MIB Functions sub-registry at
http://www.iana.org/assignments/smi-numbers according to the
procedures set forth in [I-D.dkcm-ipfix-rfc5815bis]:
Decimal Name Description Reference
------- ---- ----------- ---------
2 psampSampCountBased Count based sampling [RFCyyyy]
3 psampSampTimeBased Time based sampling [RFCyyyy]
4 psampSampRandOutOfN Random n-out-of-N sampling [RFCyyyy]
5 psampSampUniProb Universal probabilistic samp.[RFCyyyy]
6 psampFiltPropMatch Property match filtering [RFCyyyy]
7 psampFiltHash Hash filtering [RFCyyyy]
The prerequisites set forth for addition of these OIDs are to be
verified based on the content of this document.
Editor's Note (to be removed prior to publication): the IANA is
requested to assign a value for "xxx" under the 'mib-2' subtree and
to record the assignment in the SMI Numbers registry. When the
assignment has been made, the RFC Editor is asked to replace "xxx"
(here and in the MIB module) with the assigned value and to remove
this note. The RFC editor is also asked to replace "yyyy" in this
document and the MIB module by the number of the RFC when the
assignment has been made.
9. Acknowledgment
This document is a product of the PSAMP and IPFIX working groups.
The authors would like to thank the following persons: Paul Aitken
for his detailed review, Dan Romascanu and the MIB doctors, and many
more, for the technical reviews and feedback.
10. References
10.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2578] McCloghrie, K., Ed., Perkins, D., Ed., and J.
Schoenwaelder, Ed., "Structure of Management Information
Version 2 (SMIv2)", STD 58, RFC 2578, April 1999.
[RFC2579] McCloghrie, K., Ed., Perkins, D., Ed., and J.
Schoenwaelder, Ed., "Textual Conventions for SMIv2",
Dietz, et al. draft-ietf-ipfix-psamp-mib-04.txt [Page 26]
Internet-Draft PSAMP MIB October 2011
STD 58, RFC 2579, April 1999.
[RFC2580] McCloghrie, K., Perkins, D., and J. Schoenwaelder,
"Conformance Statements for SMIv2", STD 58, RFC 2580,
April 1999.
[RFC2564] Kalbfleisch, C., Krupczak, C., Presuhn, R., and J.
Saperia, "Application Management MIB", RFC 2564, May 1999.
[RFC5101] Claise, B., "Specification of the IP Flow Information
Export (IPFIX) Protocol for the Exchange of IP Traffic
Flow Information", RFC 5101, January 2008.
[RFC5477] Dietz, T., Claise, B., Aitken, P., Dressler, F., and G.
Carle, "Information Model for Packet Sampling Exports",
RFC 5477, March 2009.
[I-D.dkcm-ipfix-rfc5815bis]
Dietz, T., Kobayashi, A., Claise, B., and G. Muenz,
"Definitions of Managed Objects for IP Flow Information
Export", draft-dkcm-ipfix-rfc5815bis-00 (work in
progress), October 2011.
[RFC6340] Presuhn, R., "Textual Conventions for the Representation
of Floating-Point Numbers", RFC 6340, August 2011.
10.2. Informative References
[RFC3410] Case, J., Mundy, R., Partain, D., and B. Stewart,
"Introduction and Applicability Statements for Internet-
Standard Management Framework", RFC 3410, December 2002.
[RFC5474] Duffield, N., Chiou, D., Claise, B., Greenberg, A.,
Grossglauser, M., and J. Rexford, "A Framework for Packet
Selection and Reporting", RFC 5474, March 2009.
[RFC5475] Zseby, T., Molina, M., Duffield, N., Niccolini, S., and F.
Raspall, "Sampling and Filtering Techniques for IP Packet
Selection", RFC 5475, March 2009.
[RFC5476] Claise, B., Johnson, A., and J. Quittek, "Packet Sampling
(PSAMP) Protocol Specifications", RFC 5476, March 2009.
Dietz, et al. draft-ietf-ipfix-psamp-mib-04.txt [Page 27]
Internet-Draft PSAMP MIB October 2011
Authors' Addresses
Thomas Dietz (editor)
NEC Europe Ltd.
NEC Laboratories Europe
Kurfuersten-Anlage 36
Heidelberg 69115
DE
Phone: +49 6221 4342-128
Email: dietz@neclab.eu
Benoit Claise
Cisco Systems, Inc.
De Kleetlaan 6a b1
Degem 1831
BE
Phone: +32 2 704 5622
Email: bclaise@cisco.com
Juergen Quittek
NEC Europe Ltd.
NEC Laboratories Europe
Kurfuersten-Anlage 36
Heidelberg 69115
DE
Phone: +49 6221 4342-115
Email: quittek@neclab.eu
Dietz, et al. draft-ietf-ipfix-psamp-mib-04.txt [Page 28]