Internet Draft Sean Harnedy
InfiniSwitch Corp.
Expiration Date: November 2002 Bill Swortwood
Omegaband Inc.
May 2002
Definitions of Managed Objects for the
Infiniband Subnet Management Agent (SMA)
<draft-ietf-ipoib-subnet-mgmt-agent-mib-02.txt>
Status of this Memo
This document is an Internet-Draft and is in full conformance with
all provisions of Section 10 of RFC2026.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six
months and may be updated, replaced, or obsoleted by other documents
at any time. It is inappropriate to use Internet-Drafts as
reference material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
Copyright Notice
Copyright (C) The Internet Society (2001). All Rights Reserved.
Abstract
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in the Internet community.
In particular, it defines objects for managing Infiniband Subnet
Management Agents (SMA).
Table of Contents
1. Introduction ................................................ 2
2. The SNMP Management Framework ............................... 2
3. Conventions used in this document ........................... 3
4. Structure of the MIB ........................................ 4
4.1. Overview .................................................. 4
4.2. Discussion of MIB Groups .................................. 4
4.3. The SMA MIB Objects ....................................... 4
4.3.1. The Node Info Group ..................................... 4
4.3.2. The Switch Info Group ................................... 4
4.3.3. The GUID Info Group ..................................... 4
4.3.4. The Port Info Group ..................................... 4
Expires November 2002 [Page 1]
Internet Draft IPOVERIB SMA MIB May 2002
4.3.5. The Partition Key Group ................................. 5
4.3.6. The Service-Level-to-Virtual-Lane-Mapping Group ......... 5
4.3.7. The Virtual Lane Arbitration Group ...................... 5
4.3.8. The Linear Forwarding Group ............................. 5
4.3.9. The Random Forwarding Group ............................. 5
4.3.10. The Multicast Forwarding Group ......................... 5
4.3.11. The Subnet Manager Info Group .......................... 5
4.3.12. The Vendor Diagnostics Group ........................... 5
4.3.13. The LED Info Group ..................................... 5
4.4. The SMA Notifications Group ............................... 5
4.4.1. SMA Notifications ....................................... 6
4.5. The SMA Conformance Group ................................. 6
4.5.1. SMA Compliance Groups ................................... 6
5. IPOIB SMA MIB Definitions ................................... 6
6. Revision History ............................................ 65
6.1. Changes from <draft-ipoib-subnet-mgmt-agent-mib-00.txt> ... 65
6.2. Changes from <draft-ipoib-subnet-mgmt-agent-mib-01.txt> ... 66
7. Security Considerations ..................................... 66
8. Acknowledgements ............................................ 66
9. Intellectual Property ....................................... 66
10. References ................................................. 67
11. Authors' Addresses ......................................... 68
1. Introduction
This document defines a MIB for the InfiniBand Subnet Management
Agent (SMA).
The Infiniband Architecture[IBTAArch] is defined by the Infiniband
Trade Association. Infiniband is designed to provide low latency
high bandwidth interconnect in a computing environment. This
document will define the objects related to managing the subnet
management agent on each device in an Infiniband Fabric.
Each InfiniBand node--switch, channel adapter (CA), or router--
includes a managed entity called the Subnet Management Agent (SMA).
All SMAs in a subnet are managed by the master Subnet Manager (SM).
The SMA receives and transmits the class of Management Datagrams
(MAD) called Subnet Management Packets (SMP) when it communicates
with the SM. Note: SMPs never travel beyond the boundaries of its
local InfiniBand subnet. Also, SMPs always use Virtual Lane 15
(VL15) and are exclusively addressed to Queue Pair 0 (QP0).
2. The SNMP Management Framework
The SNMP Management Framework presently consists of five major
components:
o An overall architecture, described in RFC 2571[RFC2571].
Expires November 2002 [Page 2]
Internet Draft IPOVERIB SMA MIB May 2002
o Mechanisms for describing and naming objects and events for
the purpose of management. The first version of this
Structure of Management Information (SMI) is called SMIv1
and described in STD 16, RFC 1155[RFC1155], STD 16, RFC 1212
[RFC1212] and RFC 1215 [RFC1215]. The second version,
called SMIv2, is described in STD 58, RFC 2578[RFC2578], STD
58, RFC 2579[RFC2579], and STD 58, RFC 2580[RFC2580].
o Message protocols for transferring management information.
The first version of the SNMP message protocol is called
SNMPv1 and described in STD 15, RFC 1157[RFC1157]. A second
version of the SNMP message protocol, which is not an
Internet standards track protocol, is called SNMPv2c and
described in RFC 1901[RFC1901] and RFC 1906[RFC1906]. The
third version of the message protocol is called SNMPv3 and
described in RFC 1906[RFC1906], RFC 2572[RFC2572] and RFC
2574[RFC2574].
o Protocol operations for accessing management information.
The first set of protocol operations and associated PDU
formats is described in STD 15, RFC 1157[RFC1157]. A second
set of protocol operations and associated PDU formats is
described in RFC 1905[RFC1905].
o A set of fundamental applications described in RFC
2573[RFC2573] and the view-based access control mechanism
described in RFC 2575[RFC2575].
A more detailed introduction to the current SNMP Management
Framework can be found in RFC 2570[RFC2570].
Managed objects are accessed via a virtual information store,
termed the Management Information Base or MIB. Objects in the MIB
are defined using the mechanisms defined in the SMI.
This memo specifies a MIB module that is compliant to the SMIv2.
A MIB conforming to the SMIv1 can be produced through the
appropriate translations. The resulting translated MIB must be
semantically equivalent, except where objects or events are
omitted because no translation is possible (use of Counter64).
Some machine readable information in SMIv2 will be converted into
textual descriptions in SMIv1 during the translation process.
However, this loss of machine readable information is not
considered to change the semantics of the MIB.
3. Conventions used in this document
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL
NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in
RFC 2119 [RFC2119].
Expires November 2002 [Page 3]
Internet Draft IPOVERIB SMA MIB May 2002
4. Structure of the MIB
This section describes the structure of the IPOIB SMA MIB.
4.1. Overview
The SNMP management of the SMA involves the monitoring of key subnet
management attributes.
4.2. Discussion of MIB Groups
The SMA MIB is divided into three basic groups: MIB objects, events
(notifications), and the conformance section.
4.3. The SMA MIB Objects
The SMA MIB objects primarily correlate to the Subnet Mangagement
Attributes as defined in Table 112 Subnet Management Attributes
(Summary) from InfiniBand Architecture Release 1.0.a. Vol 1.
These attributes are organized into fourteen major SMA MIB groups.
These are: The Node Info Group, The Switch Info Group, The GUID Info
Group, the Management Port Info Group, the Data Port Info Group, the
Partition Key Group, the Service-Level-to-Virtual-Lane-Mapping Group,
the Virtual Lane Arbitration Group, the Linear Forwarding Group, the
Random Forwarding Group, the Multicast Forwarding Group, the Subnet
Manager Info Group, the Vendor Diagnostics Group, and the LED Info
Group.
4.3.1. The Node Info Group
This group provides node-level information common to any InfiniBand
node (switch, router, or CA).
4.3.2. The Switch Info Group
This group contains management information about InfiniBand switches.
4.3.3. The GUID Info Group
This group contains the assigned local scope EUI-64 identifiers for
CAs, routers, and switch management ports.
4.3.4. The Management Port Info Group
This group contains contains management information about the
management port.
4.3.5. The Data Port Info Group
This group contains contains management information about the data
ports.
Expires November 2002 [Page 4]
Internet Draft IPOVERIB SMA MIB May 2002
4.3.6. The Partition Key Group
This group contains a table with information about the Partition
Keys (P-Keys).
4.3.7. The Service-Level-to-Virtual-Lane-Mapping Group
This group contains the SLToVL Mapping Table that allows the
mapping of Virtual Lanes to Service Levels.
4.3.8. The Virtual Lane Arbitration Group
This group contains the table that can be used to examine the VL
arbitration for the node's ports.
4.3.9. The Linear Forwarding Group
This group contains information about the Linear Unicast Forwarding
Table.
4.3.10. The Random Forwarding Group
This group contains information about the Random Unicast Forwarding
Table.
4.3.11. The Multicast Forwarding Group
This group contains information about the Multicast Forwarding Table.
4.3.12. The Subnet Manager Info Group
This group contains information that the Subnet Manager can use for
its tasks of subnet discovery, polling, etc.
4.3.13. The Vendor Diagnostics Group
This group contains vendor-specific diagnostic information.
4.3.14. The LED Info Group
This group contains information about the node's LEDs.
4.4. The SMA Notifications Group
The SMA Notifications Group contains the definitions for the agent
events.
Expires November 2002 [Page 5]
Internet Draft IPOVERIB SMA MIB May 2002
4.4.1. SMA Notifications
Currently, there are several notifications which are specific for
the SMA MIB. This includes the mapping of the InfiniBand Traps
to SNMP notifications. The InfiniBand traps are summarized in
Table 114 Traps (Section 14.2.5.1) from InfiniBand Architecture
Release 1.0.a. Vol 1.
4.5. The SMA Conformance Group
The SMA Conformance Group lists the possible compliances for various
types of InfiniBand nodes (basic, full switch and full router/channel
adapter), and the units of conformance which define the constituent
object groups.
4.5.1. SMA Compliance Groups
The Compliance Groups list acceptable MIB implementation requirements.
5. IPOIB SMA MIB Definitions
SMA-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, experimental,
Counter32, NOTIFICATION-TYPE FROM SNMPv2-SMI
TEXTUAL-CONVENTION,
TruthValue FROM SNMPv2-TC
SnmpAdminString FROM SNMP-FRAMEWORK-MIB
MODULE-COMPLIANCE, OBJECT-GROUP,
NOTIFICATION-GROUP FROM SNMPv2-CONF
InterfaceIndex FROM IF-MIB
TRAP-TYPE FROM RFC-1215
IbDataPort, IbGuid,
IbUnicastLid, IbMulticastLid FROM IB-TC-MIB;
Expires November 2002 [Page 6]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaMIB MODULE-IDENTITY
LAST-UPDATED "200205101200Z" -- May 10, 2002
ORGANIZATION "IETF IP Over IB Working Group
Email: ipoib@ietf.org"
CONTACT-INFO
"Sean Harnedy (sharnedy@infiniswitch.com)
InfiniSwitch Corporation
Bill Swortwood (billiam@omegaband.com)
OmegaBand Incorporated"
DESCRIPTION
"This module contains managed object definitions for
the Subnet Management Agent instrumentation for an
InfiniBand Subnet Management Agent (SMA)."
REVISION
"200205101200Z"
DESCRIPTION
"Fixed TC assignments; LED table; GUID table index;
(-02)."
REVISION
"200203011200Z"
DESCRIPTION
"Added IANA SMI value; moved TCs to separate ID; renamed OIDs
(-01)."
REVISION
"200110200000Z"
DESCRIPTION
"Initial IETF Draft Revision (-00)."
::= { infinibandMIB 3 }
--****************************************************************
-- Object Indentifiers for the IPOIB SMA MIB
--****************************************************************
ibSmaObjects OBJECT IDENTIFIER ::= { ibSmaMIB 1 }
ibSmaNotifications OBJECT IDENTIFIER ::= { ibSmaMIB 2 }
ibSmaConformance OBJECT IDENTIFIER ::= { ibSmaMIB 3 }
--****************************************************************
-- Node Info Group
--****************************************************************
ibSmaNodeInfo OBJECT IDENTIFIER ::= { ibSmaObjects 1 }
--****************************************************************
-- NodeInfo Scalars Group
--
-- DESCRIPTION: This group contains scalar variables that describe
-- information about the node. It also contains objects that can
-- be used to monitor the behavior of this node via information
-- provided by the SMA.
--****************************************************************
Expires November 2002 [Page 7]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaNodeString OBJECT-TYPE
SYNTAX DisplayString(SIZE(1..64))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The node description. This is the Node description string
from the NodeDescription attribute. The contents of the
NodeDescription attribute is the same for all ports on a
node."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.2; Table 120 NodeDescription."
::= { ibSmaNodeInfo 1 }
ibSmaNodeBaseVersion OBJECT-TYPE
SYNTAX Integer32(1..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The supported Management Datagram (MAD) base version.
This value indicates that the node supports up to and
including this version. This value is the same for all
ports on a node. (NOTE: for InfiniBand Release 1 this
value should be set to 1.)"
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.3; Table 121 NodeInfo."
::= { ibSmaNodeInfo 2 }
ibSmaNodeClassVersion OBJECT-TYPE
SYNTAX Integer32(1..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The supported Subnet Management Class (SMP) version.
This value indicates that the node supports up to and
including this version. This value is the same for all
ports on a node. (NOTE: for InfiniBand Release 1 this
value should be set to 1.)"
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.3; Table 121 NodeInfo."
::= { ibSmaNodeInfo 3 }
Expires November 2002 [Page 8]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaNodeType OBJECT-TYPE
SYNTAX INTEGER
{
channelAdapter(1),
switch(2),
router(3),
other(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Type of IBA device this SMA is supporting. Types are
1: Channel Adapter
2: Switch
3: Router
0,4-255: reserved
NOTE: all reserved values are reported as other."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.3; Table 121 NodeInfo."
::= { ibSmaNodeInfo 4 }
ibSmaNodeNumPorts OBJECT-TYPE
SYNTAX Integer32(1..254)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of physical InfiniBand ports on this node."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.3; Table 121 NodeInfo."
::= { ibSmaNodeInfo 5 }
ibSmaNodeGuid OBJECT-TYPE
SYNTAX IbGuid
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The GUID of this node. The node can be an HCA, TCA,
switch, or router. All ports on the same node shall
report the same NodeGUID value. This provides a
means for uniquely identifing a node within a
subnet and helps to determine the co-location of
the ports."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.3; Table 121 NodeInfo."
::= { ibSmaNodeInfo 6 }
Expires November 2002 [Page 9]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaNodePortGuid OBJECT-TYPE
SYNTAX IbGuid
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The GUID of this port. One node within a port can return
the NodeGUID as its PortGUID if the port is an integral
part of the node and is not field-replaceable."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.3; Table 121 NodeInfo."
::= { ibSmaNodeInfo 7 }
ibSmaNodePartitionTableNum OBJECT-TYPE
SYNTAX Integer32(1..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of entries in the Partition Table for CA, router, and
the switch management port. This is at a minimum set to 1
for all nodes including switches."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.3; Table 121 NodeInfo."
::= { ibSmaNodeInfo 8 }
ibSmaNodeDeviceId OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(2))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Device ID information as assigned by device manufacturer."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.3; Table 121 NodeInfo."
::= { ibSmaNodeInfo 9 }
ibSmaNodeRevision OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(4))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Device revision as assigned by manufacturer."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.3; Table 121 NodeInfo."
::= { ibSmaNodeInfo 10 }
Expires November 2002 [Page 10]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaNodeLocalPortNumOrZero OBJECT-TYPE
SYNTAX Integer32(0..254)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of the IBA port which received this SNMP request.
If the port is unknown a 0 is returned."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.3; Table 121 NodeInfo."
::= { ibSmaNodeInfo 11 }
ibSmaNodeVendorId OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(3))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Device vendor Identifier as specified by the IEEE."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.3; Table 121 NodeInfo."
::= { ibSmaNodeInfo 12 }
ibSmaNodeTrapBuffer OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(256))
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"Special purpose string buffer for InfiniBand Trap Data.
This buffer contains the Notice DataDetails field for this
Trap SMP."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.1; Tables 114--119 Notice Data Details
For Traps nnn."
::= { ibSmaNodeInfo 13 }
--****************************************************************
-- Switch Info Group
--****************************************************************
ibSmaSwitchInfo OBJECT IDENTIFIER ::= { ibSmaObjects 2 }
--****************************************************************
-- SwitchInfo Scalars Group
--
-- DESCRIPTION: This group contains scalar variables that describe
-- information about an InfiniBand switch. This table shall be
-- implemented by all switches.
--****************************************************************
Expires November 2002 [Page 11]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaSwLinearFdbTableNum OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of entries in the Linear Forwarding Data Base. This
counts the number of entries supported in the Linear Unicast
Forwarding Table (starting at LID=0x0000 and going up).
The InfiniBand SwitchInfo component is called LinearFDBCap.
When this count is 0, this indicates that there is no Linear
Forwarding Database present."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 122 SwitchInfo."
::= { ibSmaSwitchInfo 1 }
ibSmaSwRandomFdbTableNum OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of entries in the Random Forwarding Data Base. This
counts the number of entries supported in the Random Unicast
Forwarding Table. The InfiniBand SwitchInfo component is
called RandomFDBCap. When this count is 0, this indicates
that there is no Random Forwarding Database present."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 122 SwitchInfo."
::= { ibSmaSwitchInfo 2 }
ibSmaSwMulticastFdbTableNum OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of entries in the Multicast Forwarding Data Base. This
counts the number of entries supported in the Multicast
Forwarding Table (starting at LID=0xC000 and going up).
The InfiniBand SwitchInfo component is called MulticastFDBCap."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 122 SwitchInfo."
::= { ibSmaSwitchInfo 3 }
Expires November 2002 [Page 12]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaSwLinearFdbTop OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the top of the linear forwarding database. Packets
received with unicast DLIDs greater than this value are
discarded by the switch. This component applies only to
switches that implement linear forwarding tables and is
ignored by switches that implement random forwarding
tables. For the latter cases a 0 is returned."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 122 SwitchInfo."
::= { ibSmaSwitchInfo 4 }
ibSmaSwDefaultPort OBJECT-TYPE
SYNTAX Integer32(0..254)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Default forwarding port for unicast packets from the other
ports whose DLID does not exist in the random forwarding
table. If the port number is unknown, a 0 is returned."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 122 SwitchInfo."
::= { ibSmaSwitchInfo 5 }
ibSmaSwDefMcastPriPort OBJECT-TYPE
SYNTAX Integer32(0..254)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Default forwarding port for multicast packets from the other
ports whose DLID does not exist in the forwarding table. If
port number is unknown, a 0 is returned."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 122 SwitchInfo. Also section
18.2.4.3.3 on Required Multicast Relay."
::= { ibSmaSwitchInfo 6 }
Expires November 2002 [Page 13]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaSwDefMcastNotPriPort OBJECT-TYPE
SYNTAX Integer32(0..254)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Forward to this port all the multicast packets from the
Default Primary port whose DLID does not exist in the
forwarding table. If it is unknown, a 0 is returned."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 122 SwitchInfo. Also section
18.2.4.3.3 on Required Multicast Relay."
::= { ibSmaSwitchInfo 7 }
ibSmaSwLifeTimeValue OBJECT-TYPE
SYNTAX Integer32(0..31)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Sets the time a packet can live in the switch. This Lifetime
Value (LV) is used as a parameter to calculate Switch Lifetime
Limit (SLL) value. To calculate a valid SLL, the LV must be
between 0 and 19, inclusive. If the LV value is greater than
19, the SLL is to be interpreted as infinite."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 122 SwitchInfo. Also section
18.2.5.4 on Transmitter Queueing."
::= { ibSmaSwitchInfo 8 }
ibSmaSwPortStateChange OBJECT-TYPE
SYNTAX Integer32(0..1)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is set to 1 whenever the PortState component
makes any of the following state changes in the link FSM:
Down-->Initialize,
Initialize-->Down,
Armed-->Down, or
Active-->Down
Also, changes in PortState resulting from SubnSet IBA command
do not change this bit. This object is set to 0 when the SMA
writes a 1; writing a 0 is ignored."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 122 SwitchInfo."
::= { ibSmaSwitchInfo 9 }
Expires November 2002 [Page 14]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaSwLidsPerPort OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the number of LID/LMC combinations that may be
assigned to a given external port for switches that support
the Random Forwarding table."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 122 SwitchInfo."
::= { ibSmaSwitchInfo 10 }
ibSmaSwPartitionEnforceNum OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the number of entries in the partition enforcement
table per physical IBA port. The 0 value indicates that
partition enforcement is not supported by the switch."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 122 SwitchInfo."
::= { ibSmaSwitchInfo 11 }
ibSmaSwInboundEnforceCap OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Flag that indicates whether the switch is capable
of partition enforcement on received packets."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 122 SwitchInfo."
::= { ibSmaSwitchInfo 12 }
ibSmaSwOutboundEnforceCap OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Flag that indicates whether the switch is capable
of partition enforcement on transmitted packets."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 122 SwitchInfo."
::= { ibSmaSwitchInfo 13 }
Expires November 2002 [Page 15]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaSwFilterRawPktInputCap OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Flag to indicate whether the switch is capable of
raw packet enforcement on received packets."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 122 SwitchInfo."
::= { ibSmaSwitchInfo 14 }
ibSmaSwFilterRawPktOutputCap OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Flag to indicate whether the switch is capable of
raw packet enforcement on transmitted packets."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 122 SwitchInfo."
::= { ibSmaSwitchInfo 15 }
--****************************************************************
-- The GUID Info Group
--****************************************************************
ibSmaGuidInfo OBJECT IDENTIFIER ::= { ibSmaObjects 3 }
-- *************************************************************
-- The Global Unique Identifier (GUID) Info Group
--
-- DESCRIPTION: The Global Unique Identifier Table.
-- *************************************************************
ibSmaGuidInfoTable OBJECT-TYPE
SYNTAX SEQUENCE OF IbSmaGuidInfoEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing SMA GUID information."
::= { ibSmaGuidInfo 1 }
ibSmaGuidInfoEntry OBJECT-TYPE
SYNTAX IbSmaGuidInfoEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row of the ibSmaGuidInfoTable containing
information about a particular GUID entry."
INDEX { ibSmaGuidPortIndex, ibSmaGuidIndex }
::= { ibSmaGuidInfoTable 1 }
Expires November 2002 [Page 16]
Internet Draft IPOVERIB SMA MIB May 2002
IbSmaGuidInfoEntry ::= SEQUENCE {
ibSmaGuidPortIndex IbDataPort,
ibSmaGuidIndex Integer32,
ibSmaGuidVal OCTET STRING
}
ibSmaGuidPortIndex OBJECT-TYPE
SYNTAX IbDataPort
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index that identifies the IB port assoicated with this
GUID table."
::= { ibGuidInfoEntry 1 }
ibSmaGuidIndex OBJECT-TYPE
SYNTAX Integer32(1..255)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index that identifies the GUID entry for this port.
For any given IB port there can be multiple 64 bit GUIDS
assigned. The maximum number is determined by the device's
implementation. If the port does not have a GUID assigned
to it, the row will have 1 entry with a value of 0."
::= { ibGuidInfoEntry 2 }
ibSmaGuidVal OBJECT-TYPE
SYNTAX IbGuid
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Global Unique Identifier (GUID) for this port entity."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.5; Table 123 GUIDInfo and
Table 124 GUID Block Element."
::= { ibGuidInfoEntry 3 }
--****************************************************************
-- The Port Info Group
--****************************************************************
ibSmaMgmtPortInfo OBJECT IDENTIFIER ::= { ibSmaObjects 4 }
ibSmaDataPortInfo OBJECT IDENTIFIER ::= { ibSmaObjects 5 }
--****************************************************************
-- PortInfo Management Port Scalars Group
--
-- DESCRIPTION: This Group contains Subnet Management Information
-- about the Management Port (InfiniBand Port 0).
--****************************************************************
Expires November 2002 [Page 17]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaPortMKey OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(8))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 8-byte management key that is kept locally
on each port. If the value is 0's, no authentication
is done."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo. Also
see Section 14.2.4."
::= { ibSmaMgmtPortInfo 1 }
ibSmaPortGidPrefix OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(8))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"GID prefix for this port."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo."
::= { ibSmaMgmtPortInfo 2 }
ibSmaPortLid OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The base LID of this port."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo."
::= { ibSmaMgmtPortInfo 3 }
ibSmaPortMasterSmLid OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The LID of the master SM that is managing this port."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo."
::= { ibSmaMgmtPortInfo 4 }
Expires November 2002 [Page 18]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaPortIsSubnetManager OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Capability flag for this node: Is Subnet Manager?"
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo."
::= { ibSmaMgmtPortInfo 5 }
ibSmaPortIsNoticeSupported OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Capability flag for this node: Are Notices Supported?"
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo."
::= { ibSmaMgmtPortInfo 6 }
ibSmaPortIsTrapSupported OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Capability flag for this node: Are IBA Traps Supported?"
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo."
::= { ibSmaMgmtPortInfo 7 }
ibSmaPortIsResetSupported OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Capability flag for this node: Is Reset Supported?"
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo."
::= { ibSmaMgmtPortInfo 8 }
Expires November 2002 [Page 19]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaPortIsAutoMigrateSupported OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Capability flag for this node: Is Automatic Migration
Supported?"
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo."
::= { ibSmaMgmtPortInfo 9 }
ibSmaPortIsSlMappingSupported OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Capability flag for this node: Is SL Mapping Supported?"
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo."
::= { ibSmaMgmtPortInfo 10 }
ibSmaPortIsMKeyNvram OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Capability flag for this node: Is M_Key in NVRAM?"
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo."
::= { ibSmaMgmtPortInfo 11 }
ibSmaPortIsPKeyNvram OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Capability flag for this node: Is P_Key in NVRAM?"
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo."
::= { ibSmaMgmtPortInfo 12 }
Expires November 2002 [Page 20]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaPortIsLedInfoSupported OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Capability flag for this node: Is LED Information
Supported?"
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo."
::= { ibSmaMgmtPortInfo 13 }
ibSmaPortIsSmDisabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Capability flag for this node: Is Subnet Manager Disabeld?"
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo."
::= { ibSmaMgmtPortInfo 14 }
ibSmaPortIsConnManageSupported OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Capability flag for this node: Is Connection Management
Supported?"
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo."
::= { ibSmaMgmtPortInfo 15 }
ibSmaPortIsSnmpTunnelSupported OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Capability flag for this node: Is SNMP Tunneling
Supported?"
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo."
::= { ibSmaMgmtPortInfo 16 }
Expires November 2002 [Page 21]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaPortIsDevManageSupported OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Capability flag for this node: Is Device Management
Supported?"
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo."
::= { ibSmaMgmtPortInfo 17 }
ibSmaPortIsVendorClassSupported OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Capability flag for this node: Is Vendor Class Supported?"
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo."
::= { ibSmaMgmtPortInfo 18 }
ibSmaPortGenericDiagCode OBJECT-TYPE
SYNTAX INTEGER {
portReady(1),
performingSelfTest(2),
initializing(3),
softError(4),
hardError(5),
other(6)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The generic portion of the Port Info Diagnostic code."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo. Also see Section
14.2.5.6.1; Table 126: Standard Encoding of DiagCode
Bits 3-0."
::= { ibSmaMgmtPortInfo 19 }
Expires November 2002 [Page 22]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaPortVendorDiagCode OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The vendor specific portion of the Port Info Diagnostic
code."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo. Also see Section
14.2.5.6.1 and Figure 162."
::= { ibSmaMgmtPortInfo 20 }
ibSmaPortMKeyLeasePeriod OBJECT-TYPE
SYNTAX Integer32(0..65535)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the initial value of the lease period timer (in
seconds). The lease period is the length of time that the
M_Key Protection bits are to remain non-zero after a
SubnSet(PortInfo) fails the M_Key authentication check.
When the value is 0, the lease period shall never expire."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo; Also Section
14.2.4.2."
::= { ibSmaMgmtPortInfo 21 }
ibSmaPortMKeyProtectBits OBJECT-TYPE
SYNTAX INTEGER {
noMKeyProtection(1),
succeedWithReturnKey(2),
succeedWithReturnZeroes(3),
failOnNoMatch(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Management Key (M_Key) protection bits. Management Key
must have a non-zero value."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo; Also
Section 14.2.4.1; Table 111 explains the Protection
Levels."
::= { ibSmaMgmtPortInfo 22 }
Expires November 2002 [Page 23]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaPortMasterSmSl OBJECT-TYPE
SYNTAX Integer32(0..15)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The administrative Service Level of the master SM that
is managing this port. "
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo."
::= { ibSmaMgmtPortInfo 23 }
ibSmaPortMKeyViolations OBJECT-TYPE
SYNTAX Gauge32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Counts the number of SMP packets that have been received at
this port that have invalid M_Keys. This object is a
latching gauge, in that whenever the maximum gauge value is
encounterd (i.e., the count reaches all 1's), the SMA must
reset the gauge to 0, before this object begins incrementing
its count again."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo."
::= { ibSmaMgmtPortInfo 24 }
ibSmaPortPKeyViolations OBJECT-TYPE
SYNTAX Gauge32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Counts the number of SMP packets that have been received at
this port that have invalid P_Keys. This object is a
latching gauge, in that whenever the maximum gauge value is
encounterd (i.e., the count reaches all 1's), the SMA must
reset the gauge to 0, before this object begins incrementing
its count again."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo; Also Section 10.9.4."
::= { ibSmaMgmtPortInfo 25 }
Expires November 2002 [Page 24]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaPortQKeyViolations OBJECT-TYPE
SYNTAX Gauge32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Counts the number of SMP packets that have been received at
this port that have invalid Q_Keys. This object is a
latching gauge, in that whenever the maximum gauge value is
encounterd (i.e., the count reaches all 1's), the SMA must
reset the gauge to 0, before this object begins incrementing
its count again."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo; Also see Section
10.2.4."
::= { ibSmaMgmtPortInfo 26 }
ibSmaPortNumGuid OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of GUID entries supported in the GUIDInfo attribute
for this port."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo."
::= { ibSmaMgmtPortInfo 27 }
ibSmaPortSubnetTimeout OBJECT-TYPE
SYNTAX Integer32(0..31)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the maximum expected subnet propagation delay,
which depends upon the configuration of the switches, to
reach any other port in the subnet and shall also be used
to determine the maximum rate which SubnTraps() can be sent
from this port by the SMA."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo."
::= { ibSmaMgmtPortInfo 28 }
Expires November 2002 [Page 25]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaPortResponseTimeValue OBJECT-TYPE
SYNTAX Integer32(0..31)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the expected maximum time between the port
reception of a SMP and the transmission of the associated
response."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo."
::= { ibSmaMgmtPortInfo 29 }
--****************************************************************
-- PortInfo InfiniBand Data Port Group
--
-- DESCRIPTION: This Group contains a table that contains the Subnet
-- Management Information about each InfiniBand data port.
--****************************************************************
ibSmaPortInfoTable OBJECT-TYPE
SYNTAX SEQUENCE OF IbSmaPortInfoEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing SMA PortInfo information."
::= { ibSmaDataPortInfo 1 }
ibSmaPortInfoEntry OBJECT-TYPE
SYNTAX IbSmaPortInfoEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row of the ibSmaPortInfoTable containing
information about a particular data port and its attributes."
INDEX { ibSmaPortIndex }
::= { ibSmaPortInfoTable 1 }
Expires November 2002 [Page 26]
Internet Draft IPOVERIB SMA MIB May 2002
IbSmaPortInfoEntry ::= SEQUENCE {
ibSmaPortIndex IbDataPort,
ibSmaPortLinkWidthEnabled INTEGER,
ibSmaPortLinkWidthSupported INTEGER,
ibSmaPortLinkWidthActive INTEGER,
ibSmaPortLinkSpeedSupported INTEGER,
ibSmaPortLinkState INTEGER,
ibSmaPortPhysState INTEGER,
ibSmaPortLinkDownDefaultState INTEGER,
ibSmaPortLinkSpeedActive INTEGER,
ibSmaPortLinkSpeedEnabled INTEGER,
ibSmaPortNeighborMtu INTEGER,
ibSmaPortVirtLaneSupport INTEGER,
ibSmaPortVlHighPriorityLimit Integer32,
ibSmaPortVlArbHighCapacity Integer32,
ibSmaPortVlArbLowCapacity Integer32,
ibSmaPortMtuCapacity INTEGER,
ibSmaPortVlStallCount Integer32,
ibSmaPortHeadOfQueueLife Integer32,
ibSmaPortOperationalVls INTEGER,
ibSmaPortPartEnforceInbound TruthValue,
ibSmaPortPartEnforceOutbound TruthValue,
ibSmaPortFilterRawPktInbound TruthValue,
ibSmaPortFilterRawPktOutbound TruthValue,
ibSmaPortLocalPhysError Integer32,
ibSmaPortOverrunError Integer32
}
ibSmaPortIndex OBJECT-TYPE
SYNTAX IbDataPort
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index that identifies the InfiniBand data port."
::= { ibSmaPortInfoEntry 1 }
Expires November 2002 [Page 27]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaPortLinkWidthEnabled OBJECT-TYPE
SYNTAX INTEGER {
noStateChange(1),
oneX(2),
fourX(3),
oneXOr4X(4),
twelveX(5),
oneXOr12X(6),
fourXOr12X(7),
oneX4XOr12X(8),
other(9)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Enabled link width, indicated as follows:
0: No State Change (NOP)
1: 1x
2: 4x
3: 1x or 4x
8: 12x
9: 1x or 12x
10: 4x or 12x
11: 1x, 4x or 12x
4 - 7, 12 - 254: Reserved (Ignored)
255: Set to LinkWidthSupported value. When writing this
field, only legal transitions are valid. See Volume 2.
[NOTE: 255 currently returns other(9) value]."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo."
::= { ibSmaPortInfoEntry 2 }
ibSmaPortLinkWidthSupported OBJECT-TYPE
SYNTAX INTEGER {
oneX(1), -- 1x
oneXOr4X(2), -- 1x or 4x
oneX4XOr12X(3), -- 1x, 4x, or 12x
other(4) -- 0, 2, 4-10, 12-255: reserved
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Supported link width for this port.
This is indicated as follows by the SMA:
1: 1x
3: 1x or 4x
11: 1x, 4x or 12x
0, 2, 4-10, 12-255: Reserved."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo."
::= { ibSmaPortInfoEntry 3 }
Expires November 2002 [Page 28]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaPortLinkWidthActive OBJECT-TYPE
SYNTAX INTEGER {
oneX(1), -- 1x
fourX(2), -- 4x
twelveX(3), -- 12x
other(4) -- 0, 3, 4-7, 9-255: reserved
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Currently active link width on this port.
This is indicated as follows by the SMA:
1: 1x
2: 4x
8: 12x
0, 3, 4-7, 9-255: Reserved."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo."
::= { ibSmaPortInfoEntry 4 }
ibSmaPortLinkSpeedSupported OBJECT-TYPE
SYNTAX INTEGER {
twoPoint5Gbps(1),
other(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Supported link speed, indicated as follows:
1: 2.5Gbps
0, 2 - 15: reserved "
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo."
::= { ibSmaPortInfoEntry 5 }
Expires November 2002 [Page 29]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaPortLinkState OBJECT-TYPE
SYNTAX INTEGER {
noStateChange(1),
downState(2),
initState(3),
armedState(4),
activeState(5),
unknownState(6)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The state of the link on this port.
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo."
::= { ibSmaPortInfoEntry 6 }
ibSmaPortPhysState OBJECT-TYPE
SYNTAX INTEGER {
noStateChange(1),
sleepState(2),
pollingState(3),
disabledState(4),
portConfigTrainingState(5),
linkUpState(6),
linkErrorRecoveryState(7),
unknownState(8)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Physical Port State. Enumerated as:
0: No state change
1: Sleep
2: Polling
3: Disabled
4: PortConfigurationTraining
5: LinkUp
6: LinkErrorRecovery
7 - 15: Reserved - ignored When SM is writing this
field, only legal transitions are valid. See Volume
2."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo."
::= { ibSmaPortInfoEntry 7 }
Expires November 2002 [Page 30]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaPortLinkDownDefaultState OBJECT-TYPE
SYNTAX INTEGER {
noStateChange(1),
sleepState(2),
pollingState(3),
unknownState(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"LinkDownDefault-State
0: No state change
1: Sleep
2: Polling
3 - 15: Reserved - ignored When writing this field, only
legal transitions are valid. See Volume 2. "
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo."
::= { ibSmaPortInfoEntry 8 }
ibSmaPortLinkSpeedActive OBJECT-TYPE
SYNTAX INTEGER {
twoPoint5Gbps(1),
other(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Currently active link speed, indicated as follows:
1: 2.5Gbps
0, 2 - 15: reserved."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo."
::= { ibSmaPortInfoEntry 9 }
Expires November 2002 [Page 31]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaPortLinkSpeedEnabled OBJECT-TYPE
SYNTAX INTEGER {
twoPoint5Gbps(1),
other(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Enabled link speed, indicated as follows:
0: No State Change (NOP)
1: 2.5 Gbps
2 - 14: Reserved (Ignored)
15: Set to LinkSpeedSupported value."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo."
::= { ibSmaPortInfoEntry 10 }
ibSmaPortNeighborMtu OBJECT-TYPE
SYNTAX INTEGER {
mtu256(1),
mtu512(2),
mtu1024(3),
mtu2048(4),
mtu4096(5),
other(6)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Active maximum MTU enabled on this port for transmit:
1: 256 bytes
2: 512 bytes
3: 1024 bytes
4: 2048 bytes
5: 4096 bytes
0, 6 - 15: reserved "
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo."
::= { ibSmaPortInfoEntry 11 }
Expires November 2002 [Page 32]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaPortVirtLaneSupport OBJECT-TYPE
SYNTAX INTEGER {
vl0(1), -- virtual lane 0
vl0ToVl1(2), -- VL0, VL1
vl0ToVl3(3), -- VL0 to VL3
vl0ToVl7(4), -- VL0 to VL7
vl0ToVl14(5), -- VL0 to VL14
other(6) -- reserved
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Virtual Lane configuration supported on this port.
Indicated as as follows by the SMA:
1: VL0
2: VL0, VL1
3: VL0 - VL3
4: VL0 - VL7
5: VL0 - VL14
0, 6 - 15: reserved."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo."
::= { ibSmaPortInfoEntry 12 }
ibSmaPortVlHighPriorityLimit OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Limit of High Priority component of VL Arbitration Table.
This object indicates the amount of high priority packets
that can be trasnmitted wihout an opportunity to send a
low priority packet. Specifically, the number of bytes
that can be sent is this value times 4K bytes. A 255 value
means the byte limit is unbounded and a value of 0 means
that only a single packet from the high-priority table
may be sent before an opportunity is given to the low-
priority table."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo; See also Section 7.6.9."
::= { ibSmaPortInfoEntry 13 }
Expires November 2002 [Page 33]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaPortVlArbHighCapacity OBJECT-TYPE
SYNTAX Integer32(0..64)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"VL/Weight pairs supported on this port in the VLArbitration
table for high priority. Shall be 1 to 64 if more than one
data VL is supported on this port, 0 otherwise."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo; Also Section 7.6.9."
::= { ibSmaPortInfoEntry 14 }
ibSmaPortVlArbLowCapacity OBJECT-TYPE
SYNTAX Integer32(0..64)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"VL/Weight pairs supported on this port in the VLArbitration
table for low priority. Shall be N to 64 if more than one
data VL is supported on this port, 0 otherwise, N being the
number of data VLs supported."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo; Also see Section 7.6.9."
::= { ibSmaPortInfoEntry 15 }
ibSmaPortMtuCapacity OBJECT-TYPE
SYNTAX INTEGER {
mtu256(1),
mtu512(2),
mtu1024(3),
mtu2048(4),
mtu4096(5),
other(6)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Maximum MTU supported by this port.
1: 256 bytes
2: 512 bytes
3: 1024 bytes
4: 2048 bytes
5: 4096 bytes
0, 6 - 15: reserved "
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo."
::= { ibSmaPortInfoEntry 16 }
Expires November 2002 [Page 34]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaPortVlStallCount OBJECT-TYPE
SYNTAX Integer32(0..7)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the number of sequential packets dropped that
causes the port to enter the VLStalled state."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo; Section 18.2.4.4."
::= { ibSmaPortInfoEntry 17 }
ibSmaPortHeadOfQueueLife OBJECT-TYPE
SYNTAX Integer32(0..31)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Sets the time a packet can live at the head of a
Virtual Lane queue. This variable (HL) is used to
compute the Head of the Queue Lifetime Limit (HLL).
It is used in the formula when the HL value is between
0 and 19, inclusive. When HL is greater than 19, the
HLL is to be interpreted as infinite."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo; Also Section 18.2.5.4."
::= { ibSmaPortInfoEntry 18 }
ibSmaPortOperationalVls OBJECT-TYPE
SYNTAX INTEGER {
vl0(1), -- virtual lane 0
vl0ToVl1(2), -- VL0, VL1
vl0ToVl3(3), -- VL0 to VL3
vl0ToVl7(4), -- VL0 to VL7
vl0ToVl14(5), -- VL0 to VL14
other(6) -- reserved
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Virtual Lanes operational on this port, indicated
as follows:
0: No change
1: VL0
2: VL0 - VL1
3: VL0 - VL3
4: VL0 - VL7
5: VL0 - VL14
6 - 15: reserved"
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo."
::= { ibSmaPortInfoEntry 19 }
Expires November 2002 [Page 35]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaPortPartEnforceInbound OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates support of optional inbound partition enforcement.
If true, partition enforcement on packets received on this
port is enabled. If false partition enforcement on
packets received from this port is disabled."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo."
::= { ibSmaPortInfoEntry 20 }
ibSmaPortPartEnforceOutbound OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates support of optional outbound partition
enforcement. If true, partition enforcement on packets
transmitted on this port is enabled. If false partition
enforcement on packets transmitted from this port is
disabled."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo."
::= { ibSmaPortInfoEntry 21 }
ibSmaPortFilterRawPktInbound OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates support of optional inbound raw packet
enforcement. If true, raw packets arriving on this port
are discarded. If false, raw enforcement on packets received
from this port is disabled."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo."
::= { ibSmaPortInfoEntry 22 }
Expires November 2002 [Page 36]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaPortFilterRawPktOutbound OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates support of optional outbound raw packet
enforcement. If true, raw packets departing on this port
are discarded. If false, raw enforcement on packets leaving
from this port is disabled."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo."
::= { ibSmaPortInfoEntry 23 }
ibSmaPortLocalPhysError OBJECT-TYPE
SYNTAX Integer32(0..15)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Local Physical Error threshold value. When the count of
marginal link errors exceeds this threshold, the local
link integrity error shall be detected."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo; Also Section 7.12.2."
::= { ibSmaPortInfoEntry 24 }
ibSmaPortOverrunError OBJECT-TYPE
SYNTAX Integer32(0..15)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Overrun error threshold value. When the count of buffer
overruns over consecutive flow control update periods
exceeds this threshold, the excessive buffer overrun
error shall be detected."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo; Also Section 7.12.2."
::= { inSmaPortInfoEntry 25 }
--****************************************************************
-- The Partition Key Group
--****************************************************************
ibSmaPKeyInfo OBJECT IDENTIFIER ::= { ibSmaObjects 6 }
-- *************************************************************
-- The Partition Key (P_Key) Table
--
-- DESCRIPTION: This table contains SMA information about the
-- Partition Key Table.
-- *************************************************************
Expires November 2002 [Page 37]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaPKeyTable OBJECT-TYPE
SYNTAX SEQUENCE OF IbPKeyEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains SMA Partition Key information for
this port."
::= { ibSmaPKeyInfo 1 }
ibSmaPKeyEntry OBJECT-TYPE
SYNTAX IbPKeyEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row of the ibPKeyTable containing
information about the partition keys."
INDEX { ibPKeyIBAPortIndex, ibPKeyIndex }
::= { ibPKeyTable 1 }
IbSmaPKeyEntry ::= SEQUENCE {
ibSmaPKeyIBAPortIndex IbDataPort,
ibSmaPKeyIndex Integer32,
ibSmaPKeyMembership INTEGER,
ibSmaPKeyBase OCTET STRING
}
ibSmaPKeyIBAPortIndex OBJECT-TYPE
SYNTAX IbDataPort
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The IB data port index."
::= { ibSmaPKeyEntry 1 }
ibSmaPKeyIndex OBJECT-TYPE
SYNTAX Integer32 (1..1024)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The 1-based entry Identifier for each Partition Key
defined on a port"
::= { ibSmaPKeyEntry 2 }
Expires November 2002 [Page 38]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaPKeyMembership OBJECT-TYPE
SYNTAX INTEGER {
none(1),
limited(2),
full(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If the P_Key type is limited, the switch may accept a
packet with a matching full P_Key, but may not accept a
packet with a matching limited key. If the P_Key type
is full, the switch can accept packets with either a
full or limited P_Key. If the P_Key type is none,
there is no associated Key Base."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.7; Table 127 P_KeyTable and
Table 128 P_Key Block Element."
::= { ibSmaPKeyEntry 3 }
ibSmaPKeyBase OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(2))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Base value of the P_Key that the switch will use to
check against incoming packets."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.7; Table 127 P_KeyTable and
Table 128 P_Key Block Element."
::= { ibSmaPKeyEntry 4 }
--****************************************************************
-- The Service-Level-to-Virtual-Lane-Mapping Group
--****************************************************************
ibSmaSlToVlMapInfo OBJECT IDENTIFIER ::= { ibSmaObjects 7 }
-- *************************************************************
-- The Service Level to Virtual Lane Configuration Mapping Table
--
-- DESCRIPTION: This table reflects the current Service Level
-- value for the input port/output port/virtual lane.
-- *************************************************************
Expires November 2002 [Page 39]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaSL2VLMapTable OBJECT-TYPE
SYNTAX SEQUENCE OF IbSmaSL2VLMapEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides the virtual lane value for the
output port/input port/service level mapping.
Each output port contains a VL mapping for the
next hop based on the input port the packet arrived
on and its SL value."
::= { ibSmaSlToVlMapInfo 1 }
ibSmaSL2VLMapEntry OBJECT-TYPE
SYNTAX IbSmaSL2VLMapEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Column definitions for the VL to output/input/VL entry."
INDEX { ibSmaIBAOutPortIndex, ibSmaIBAInPortIndex,
ibSmaServiceLevelIndex }
::= { ibSmaSL2VLMapTable 1 }
IbSmaSL2VLMapEntry ::= SEQUENCE {
ibSmaIBAOutPortIndex IbDataPort,
ibSmaIBAInPortIndex IbDataPort,
ibSmaServiceLevelIndex Integer32,
ibSmaVirtualLane Integer32
}
ibSmaIBAOutPort OBJECT-TYPE
SYNTAX IbDataPort
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The egress port index for the service level Mapping."
::= { ibSmaSL2VLMapEntry 1 }
ibSmaIBAInPort OBJECT-TYPE
SYNTAX IbDataPort
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The ingress port index for the service level Mapping."
::= { ibSmaSL2VLMapEntry 2 }
ibSmaServiceLevel OBJECT-TYPE
SYNTAX Integer32(1..16)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The (1-based) Service Level value index for this mapping."
::= { ibSmaSL2VLMapEntry 3 }
Expires November 2002 [Page 40]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaVirtualLane OBJECT-TYPE
SYNTAX Integer32(0..15)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The outgoing packet's Virtual Lane value for
this Service Level Mapping."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.8.; Table 129 SLtoVLMappingTable."
::= { ibSmaSL2VLMapEntry 4 }
--****************************************************************
-- The Virtual Lane Arbitration Group
--****************************************************************
ibSmaVLArbitInfo OBJECT IDENTIFIER ::= { ibSmaObjects 8 }
-- *************************************************************
-- The Virtual Lane High Priority Arbitration Table
--
-- DESCRIPTION: This table contains the VL High Priority
-- Arbitration Table. The second index is the list index
-- that allows for the viewing of the configuration of the
-- VL/weight pairs configured by the SM.
-- *************************************************************
ibSmaHiPriVlArbTable OBJECT-TYPE
SYNTAX SEQUENCE OF IbSmaHiPriVlArbEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides visibility into the High Priority
Arbitration process for configuring VL/Weight pairs for
the IB data ports."
::= { ibSmaVLArbitInfo 1 }
ibSmaHiPriVlArbEntry OBJECT-TYPE
SYNTAX IbSmaHiPriVlArbEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Column definitions for High Priority Arbitration Table."
INDEX { ibSmaHiPriIBAPortIndex, ibSmaHiPriNIndex }
::= { ibSmaHiPriVlArbTable 1 }
IbSmaHiPriVlArbEntry ::= SEQUENCE {
ibSmaHiPriIBAPortIndex IbDataPort,
ibSmaHiPriNIndex Integer32,
ibSmaHiPriVirtLane Integer32,
ibSmaHiPriWeight Integer32
}
Expires November 2002 [Page 41]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaHiPriIBAPortIndex OBJECT-TYPE
SYNTAX IbDataPort
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The index for the IBA port that is being configured."
::= { ibSmaHiPriVlArbEntry 1 }
ibSmaHiPriNIndex OBJECT-TYPE
SYNTAX Integer32 (1..64)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The High Priority list index."
::= { ibHiPriVlArbEntry 2 }
ibSmaHiPriVirtLane OBJECT-TYPE
SYNTAX Integer32(0..14)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The virtual lane this entry applies to."
::= { ibSmaHiPriVlArbEntry 3 }
ibSmaHiPriWeight OBJECT-TYPE
SYNTAX Integer32 (0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of 64-byte units that may be transmitted from this
VL when its turn in the arbitration process occurs. A weight
of 0 indicates that the entry should be skipped."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.9; Table 130 VLArbitrationTable."
::= { ibSmaHiPriVlArbEntry 4 }
-- *************************************************************
-- The Virtual Lane Low Priority Arbitration Table
--
-- DESCRIPTION: This table contains the VL Low Priority Arbitration
-- Table. The second index is the list index that allows for the
-- viewing of the configuration of the VL/weight pairs done by SM.
-- *************************************************************
ibSmaLowPriVlArbTable OBJECT-TYPE
SYNTAX SEQUENCE OF IbSmaLowPriVlArbEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides visibility into the Low Priority
Arbitration process."
::= { ibSmaVLArbitInfo 2 }
Expires November 2002 [Page 42]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaLowPriVlArbEntry OBJECT-TYPE
SYNTAX IbSmaLowPriVlArbEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Column definitions for Low Priority Arbitration Table."
INDEX { ibSmaLowPriIBAPortIndex, ibSmaLowPriNIndex }
::= { ibSmaLowPriVlArbTable 1 }
IbSmaLowPriVlArbEntry ::= SEQUENCE {
ibSmaLowPriIBAPortIndex IbDataPort,
ibSmaLowPriNIndex Integer32,
ibSmaLowPriVirtLane Integer32,
ibSmaLowPriWeight Integer32
}
ibSmaLowPriIBAPort OBJECT-TYPE
SYNTAX IbDataPort
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The index for the IB data port that is being configured."
::= { ibSmaLowPriVlArbEntry 1 }
ibSmaLowPriNIndex OBJECT-TYPE
SYNTAX Integer32(1..64)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Low Priority list index."
::= { ibSmaLowPriVlArbEntry 2 }
ibSmaLowPriVirtLane OBJECT-TYPE
SYNTAX Integer32(0..14)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Virtual Lane this entry applies to."
::= { ibSmaLowPriVlArbEntry 3 }
ibSmaLowPriWeight OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of 64-byte units that may be transmitted from this VL
when its turn in the arbitration process occurs. A weight
of 0 indicates that the entry should be skipped."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.9; Table 130 VLArbitrationTable."
::= { ibSmaLowPriVlArbEntry 4 }
Expires November 2002 [Page 43]
Internet Draft IPOVERIB SMA MIB May 2002
--****************************************************************
-- The Linear Forwarding Group
--****************************************************************
ibSmaLFTInfo OBJECT IDENTIFIER ::= { ibSmaObjects 9 }
--****************************************************************
-- Linear Forwarding Table Group: ibLinForTable
--
-- DESCRIPTION: This table contains information about the Linear
-- Forwarding Table.
--****************************************************************
ibSmaLinForTable OBJECT-TYPE
SYNTAX SEQUENCE OF IbSmaLinForEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing information about the Linear Forwarding
Table."
::= { ibSmaLFTInfo 1 }
ibSmaLinForEntry OBJECT-TYPE
SYNTAX IbSmaLinForEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Current unicast forwarding Table entry configured by the
Subnet Manager based on destination LID."
INDEX { ibSmaLinDestDLIDIndex }
::= { ibSmaLinForTable 1 }
IbSmaLinForEntry ::= SEQUENCE {
ibSmaLinDestDLIDIndex IbUnicastLid,
ibSmaLinForwEgressPort IbDataPort
}
ibSmaLinDestDLIDIndex OBJECT-TYPE
SYNTAX IbUnicastLid
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index that identifies Destination Local Identifier (DLID)
that the forwarding entry refers to in the Linear Forwarding
Table."
REFERENCE
"InfiniBand Architecture Release 1.0.a Vol 1
Section 14.2.5.10 LinearForwardingTable; Table 132 and
Table 133."
::= { ibSmaLinForEntry 1 }
Expires November 2002 [Page 44]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaLinForwEgressPort OBJECT-TYPE
SYNTAX IbDataPort
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The port to which packets with the LID corresponding to
this entry are to be forwarded."
REFERENCE
"InfiniBand Architecture Release 1.0.a Vol 1
Section 14.2.5.10 LinearForwardingTable; Table 132 and
Table 133."
::= { ibSmaLinForEntry 2 }
--****************************************************************
-- The Random Forwarding Group
--****************************************************************
ibSmaRFTInfo OBJECT IDENTIFIER ::= { ibSmaObjects 10 }
--****************************************************************
-- Random Forwarding Table
--
-- DESCRIPTION: This Table contains Subnet Management Information
-- about the Random Forwarding Table.
--****************************************************************
ibSmaRandomForwardingTable OBJECT-TYPE
SYNTAX SEQUENCE OF IbSmaRandomForwardingEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing SMA Random Forwarding information."
::= { ibSmaRFTInfo 1 }
ibSmaRandomForwardingEntry OBJECT-TYPE
SYNTAX IbSmaRandomForwardingEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row of the ibSmaRandomForwardingTable
containing information about the Random Forwarding Table."
INDEX { ibSmaRandomForwardingPortIndex }
::= { ibSmaRandomForwardingTable 1 }
IbSmaRandomForwardingEntry ::= SEQUENCE {
ibSmaRandomForwardingPortIndex IbDataPort,
ibSmaRandomDestLID Integer32,
ibSmaRandomForwEgressPort Integer32,
ibSmaRandomLMC Integer32,
ibSmaRandomIsValid TruthValue
}
Expires November 2002 [Page 45]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaRandomForwardingPortIndex OBJECT-TYPE
SYNTAX IbDataPort
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The port index value."
::= { ibSmaRandomForwardingEntry 1 }
ibSmaRandomDestLID OBJECT-TYPE
SYNTAX Integer32(1..49152)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Identifies Destination Local Identifier (DLID) that the
forwarding entry refers to."
REFERENCE
"InfiniBand Architecture Release 1.0.a Vol 1
Section 14.2.5.11 RandomForwardingTable; Table 134 and
Table 135."
::= { ibSmaRandomForwardingEntry 2 }
ibSmaRandomForwEgressPort OBJECT-TYPE
SYNTAX IbDataPort
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The port to which packets with the LID corresponding to this
entry are to be forwarded."
REFERENCE
"InfiniBand Architecture Release 1.0.a Vol 1
Section 14.2.5.11 RandomForwardingTable; Table 134 and
Table 135."
::= { ibSmaRandomForwardingEntry 3 }
ibSmaRandomLMC OBJECT-TYPE
SYNTAX Integer32(0..7)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The LMC of this LID."
REFERENCE
"InfiniBand Architecture Release 1.0.a Vol 1
Section 14.2.5.11 RandomForwardingTable; Table 134 and
Table 135."
::= { ibSmaRandomForwardingEntry 4 }
Expires November 2002 [Page 46]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaRandomIsValid OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If true this LID/Port pair is valid. Note that when the SMA
sets this parameter to 0, entries can be removed."
REFERENCE
"InfiniBand Architecture Release 1.0.a Vol 1
Section 14.2.5.11 RandomForwardingTable; Table 134 and
Table 135."
::= { ibSmaRandomForwardingEntry 5 }
--****************************************************************
-- The Multicast Forwarding Group
--****************************************************************
ibSmaMFTInfo OBJECT IDENTIFIER ::= { ibSmaObjects 11 }
--****************************************************************
-- Multicast Forwarding Table Group: ibMulForTable
--
-- DESCRIPTION: This table contains information about the Multicast
-- Forwarding Table.
--****************************************************************
ibSmaMulForTable OBJECT-TYPE
SYNTAX SEQUENCE OF IbSmaMulForEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing information about the Multicast Forwarding
Table."
::= { ibSmaMFTInfo 1 }
ibSmaMulForEntry OBJECT-TYPE
SYNTAX IbMulForEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Current multicast forwarding table entry as configured by the
Subnet Manager based on destination LID."
INDEX { ibSmaMulDestDLIDIndex }
::= { ibSmaMulForTable 1 }
IbSmaMulForEntry ::= SEQUENCE {
ibSmaMulDestDLIDIndex IbMulticastLid,
ibSmaMulForwMask IbSmPortList
}
Expires November 2002 [Page 47]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaMulDestDLID OBJECT-TYPE
SYNTAX IbMulticastLid
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Identifies Destination Local Identifier (DLID) that the
forwarding entry refers to in the Multicast Forwarding Table."
REFERENCE
"InfiniBand Architecture Release 1.0.a Vol 1
Section 14.2.5.12 MulticastForwardingTable; Table 136 and
Table 137."
::= { ibSmaMulForEntry 1 }
ibSmaMulForwMask OBJECT-TYPE
SYNTAX IbSmPortList
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A 256 bit mask that represents a port list. An incoming packet
with this LID table entry will be forwarded to all ports for
which the bit in the port mask is set to 1."
REFERENCE
"InfiniBand Architecture Release 1.0.a Vol 1
Section 14.2.5.12 MulticastForwardingTable; Table 136 and
Table 137."
::= { ibSmaMulForEntry 2 }
--****************************************************************
-- The Subnet Manager Info Group
--****************************************************************
ibSmaSMInfo OBJECT IDENTIFIER ::= { ibSmaObjects 12 }
--****************************************************************
-- Subnet Manager Information Table Group
--****************************************************************
ibSmaSubMgrInfo OBJECT IDENTIFIER ::= { ibSmaSMInfo 1 }
--****************************************************************
-- Subnet Manager Information Table
--
-- DESCRIPTION: This Table contains Subnet Management Information
-- about the Subnet Managers on this subnet. This information
-- is available on a port where a Subnet Manager resides.
--****************************************************************
ibSmaSmInfoTable OBJECT-TYPE
SYNTAX SEQUENCE OF IbSmaSmInfoEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing SMA Subnet Manager information."
::= { ibSmaSubMgrInfo 1 }
Expires November 2002 [Page 48]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaSmInfoEntry OBJECT-TYPE
SYNTAX IbSmaSmInfoEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row of the ibSmaSmInfoTable containing
information about the Subnet Manager Table."
INDEX { ibSmaSmInfoPortIndex }
::= { ibSmaSmInfoTable 1 }
IbSmaSmInfoEntry ::= SEQUENCE {
ibSmaSmInfoPortIndex IbDataPort,
ibSmaSmGuid OCTET STRING,
ibSmaSmSmKey OCTET STRING,
ibSmaSmSmpCount Counter32,
ibSmaSmPriority Integer32,
ibSmaSmState INTEGER
}
ibSmaSmInfoPortIndex OBJECT-TYPE
SYNTAX IbDataPort
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The port index value."
::= { ibSmaSmInfoEntry 1 }
ibSmaSmGuid OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(8))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Port GUID of the port where the SM resides."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.13; Table 138 SMInfo Table."
::= { ibSmaSmInfoEntry 2 }
ibSmaSmSmKey OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(8))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Key for this SM. This is shown as zeroes unless the
requesting SM is proven to be the master, or the
requester is otherwise authenticated."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.13; Table 138 SMInfo Table."
::= { ibSmaSmInfoEntry 3 }
Expires November 2002 [Page 49]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaSmSmpCount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Counter that increments each time the SM issues an
SMP or performs other management activities. This
counter is used as a heartbeat indicator by standby SMs."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.13; Table 138 SMInfo Table."
::= { ibSmaSmInfoEntry 4 }
ibSmaSmPriority OBJECT-TYPE
SYNTAX Integer32(0..15)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Administratively assigned priority for this SM. This
can be reset by master SM. 0 is the lowest priority."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.13; Table 138 SMInfo Table."
::= { ibSmaSmInfoEntry 5 }
ibSmaSmState OBJECT-TYPE
SYNTAX INTEGER
{
unknown(1),
notActive(2),
discovering(3),
standby(4),
master(5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Enumerated value indicating this SM's state.
The InfiniBand enumeration values are:
0 - not active
1 - discovering
2 - standby
3 - master
4-15 - reserved.
Note: a value of reserved returns unknown(1)."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.13; Table 138 SMInfo Table."
::= { ibSmaSmInfoEntry 6 }
Expires November 2002 [Page 50]
Internet Draft IPOVERIB SMA MIB May 2002
--****************************************************************
-- The Vendor Diagnostics Group
--****************************************************************
ibSmaVendDiagInfo OBJECT IDENTIFIER ::= { ibSmaObjects 13 }
--****************************************************************
-- Vendor Diagnostics Information Table
--
-- DESCRIPTION: This Table contains Subnet Management Information
-- about the Vendor Diagnostics.
--****************************************************************
ibSmaVendDiagInfoTable OBJECT-TYPE
SYNTAX SEQUENCE OF IbSmaVendDiagInfoEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing SMA Vendor Diagnostic Info information."
::= { ibSmaVendDiagInfo 1 }
ibSmaVendDiagInfoEntry OBJECT-TYPE
SYNTAX IbSmaVendDiagInfoEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row of the ibSmaVendDiagInfoTable containing
information about a particular data port's diagnostic status."
INDEX { ibSmaVendDiagPortIndex }
::= { ibSmaLedInfoTable 1 }
IbSmaVendDiagInfoEntry ::= SEQUENCE {
ibSmaVendDiagPortIndex IbDataPort,
ibSmaPortGenericDiagCode INTEGER,
ibSmaPortVendorDiagCode INTEGER,
ibSmaPortVendorDiagIndexFwd TruthValue,
ibSmaPortVendorDiagData OCTET STRING
}
ibSmaVendDiagPortIndex OBJECT-TYPE
SYNTAX IbDataPort
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index that identifies the port for the diagnostics."
::= { ibSmaVendDiagInfoEntry 1 }
Expires November 2002 [Page 51]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaPortGenericDiagCode OBJECT-TYPE
SYNTAX INTEGER {
portReady(1),
performingSelfTest(2),
initializing(3),
softError(4),
hardError(5),
other(6)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The generic portion of the Port Info Diagnostic code."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo. Also see Section
14.2.5.6.1; Table 126: Standard Encoding of DiagCode
Bits 3-0."
::= { ibSmaVendDiagInfoEntry 2 }
ibSmaPortVendorDiagCode OBJECT-TYPE
SYNTAX Integer32(0..2047)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The vendor specific portion of the Port Info Diagnostic
code."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 125 PortInfo. Also see Section
14.2.5.6.1 and Figure 162."
::= { ibSmaVendDiagInfoEntry 3 }
ibSmaPortVendorDiagIndexFwd OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Flag to control ibSmaPortVendorDiagData data buffer. If
this boolean is true(1), the data buffer contains meaningful
vendor-supplied additional diagnostic information. If this
object is false(2), the buffer is empty or this was the final
data buffer in the chain."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Table 139 VendorDiag."
::= { ibSmaVendDiagInfoEntry 4 }
Expires November 2002 [Page 52]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaPortVendorDiagData OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(62))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Data buffer that can contain additional vendor-specific
diagnostic information. The ibSmaPortVendorDiag flag
controls whether this object contains meaningful data."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.4; Table 139 VendorDiag. Also see Section
14.2.5.14 and Figure 163."
::= { ibSmaVendDiagInfoEntry 5 }
--****************************************************************
-- The LED Info Group
--****************************************************************
ibSmaLedInfo OBJECT IDENTIFIER ::= { ibSmaObjects 14 }
--****************************************************************
-- LED Information Table
--
-- DESCRIPTION: This Table contains Subnet Management Information
-- about the LEDs.
--****************************************************************
ibSmaLedInfoTable OBJECT-TYPE
SYNTAX SEQUENCE OF IbSmaLedInfoEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing SMA LED Info information."
::= { ibSmaLedInfo 1 }
ibSmaLedInfoEntry OBJECT-TYPE
SYNTAX IbSmaLedInfoEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A conceptual row of the ibSmaLedInfoTable containing
information about a particular data port's LED status."
INDEX { ibSmaLedIndex }
::= { ibSmaLedInfoTable 1 }
IbSmaLedInfoEntry ::= SEQUENCE {
ibSmaLedIndex IbDataPort,
ibSmaLedState INTEGER
}
Expires November 2002 [Page 53]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaLedIndex OBJECT-TYPE
SYNTAX IbDataPort
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index that identifies the IB data port that can have an
LED associated with it."
::= { ibSmaLedInfoEntry 1 }
ibSmaLedState OBJECT-TYPE
SYNTAX INTEGER
{
unknown(1),
on(2),
off(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"State of the LED."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.15 LedInfo; Table 140 LedInfo Table."
::= { ibSmaLedInfoEntry 2 }
--****************************************************************
-- Notifications Group
--****************************************************************
ibSmaNotificationPrefix OBJECT IDENTIFIER ::= { ibSmaNotifications 0 }
--****************************************************************
-- Notifications
--
-- DESCRIPTION: The Notifications Group contains the set
-- of SMA Traps that will be translated into SNMP
-- notifications and sent to the proper NMS manager.
--****************************************************************
ibSmaPortNowInService NOTIFICATION-TYPE
OBJECTS
{
ibSmaNodeTrapBuffer
}
STATUS current
DESCRIPTION
"This notification translates InfiniBand SMA Trap 64."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.1; Table 114 and 115."
::= { ibSmaNotifications 1 }
Expires November 2002 [Page 54]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaPortOutOfService NOTIFICATION-TYPE
OBJECTS
{
ibSmaNodeTrapBuffer
}
STATUS current
DESCRIPTION
"This notification translates InfiniBand SMA Trap 65."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.1; Table 114 and 115."
::= { ibSmaNotifications 2 }
ibSmaPortLinkStateChange NOTIFICATION-TYPE
OBJECTS
{
ibSmaNodeTrapBuffer
}
STATUS current
DESCRIPTION
"128:Link State of at least one port has changed."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.1; Table 114 and 116."
::= { ibSmaNotifications 3 }
ibSmaLinkIntegrityThresReached NOTIFICATION-TYPE
OBJECTS
{
ibSmaPortLid,
ibSmaNodeTrapBuffer
}
STATUS current
DESCRIPTION
"129:any Local Link Integrity threshold reached at
<LIDADDR><PORTNO>."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.1; Table 114 and 117."
::= { ibSmaNotifications 4 }
Expires November 2002 [Page 55]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaExcessBuffOverrunThres NOTIFICATION-TYPE
OBJECTS
{
ibSmaPortLid,
ibSmaNodeTrapBuffer
}
STATUS current
DESCRIPTION
"130:any Exccessive Buffer Overrun threshold reached at
<LIDADDR><PORTNO>"
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.1; Table 114 and 117."
::= { ibSmaNotifications 5 }
ibSmaFlowCntrlUpdateTimerExpire NOTIFICATION-TYPE
OBJECTS
{
ibSmaPortLid,
ibSmaNodeTrapBuffer
}
STATUS current
DESCRIPTION
"131:switch Flow Control Update watchdog timer expired at
<LIDADDR><PORTNO>"
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.1; Table 114 and 117."
::= { ibSmaNotifications 6 }
ibSmaBadManagementKey NOTIFICATION-TYPE
OBJECTS
{
ibSmaPortLid,
ibSmaNodeTrapBuffer
}
STATUS current
DESCRIPTION
"256:any Bad M_Key, <MKEY> from <LIDADDR> attempted <METHOD>
with <ATTRIBUTEID> and <ATTRIBUTEMODIFIER>."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.1; Table 114 and 118."
::= { ibSmaNotifications 7 }
Expires November 2002 [Page 56]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaBadPartitionKey NOTIFICATION-TYPE
OBJECTS
{
ibSmaPortLid,
ibSmaNodeTrapBuffer
}
STATUS current
DESCRIPTION
"257:any Bad P_Key, <KEY> from <LIDADDR1> /<GIDADDR1>/<QP1> to
<LIDADDR2>/<GIDADDR2>/<QP2> on <SL>. "
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.1; Table 114 and 119."
::= { ibSmaNotifications 8 }
ibSmaBadQueueKey NOTIFICATION-TYPE
OBJECTS
{
ibSmaPortLid,
ibSmaNodeTrapBuffer
}
STATUS current
DESCRIPTION
"258:any Bad Q_Key, <KEY> from <LIDADDR1>/<GIDADDR1>/<QP1> to
<LIDADDR2>/<GIDADDR2>/<QP2> on <SL>."
REFERENCE
"InfiniBand Architecture Release 1.0.a. Vol 1.
Section 14.2.5.1; Table 114 and 119."
::= { ibSmaNotifications 9 }
--****************************************************************
-- Module Conformance Statement
--
-- DESCRIPTION: The module conformance statement includes the
-- compliance statements and the units of conformance
-- section.
--****************************************************************
ibSmaCompliances OBJECT IDENTIFIER ::= { ibSmaConformance 1 }
ibSmaGroups OBJECT IDENTIFIER ::= { ibSmaConformance 2 }
Expires November 2002 [Page 57]
Internet Draft IPOVERIB SMA MIB May 2002
--****************************************************************
-- Compliance Statements
--****************************************************************
ibSmaBasicNodeCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The basic node implementation requirements for agents that
support the IPOIB SMA MIB."
MODULE -- this module
MANDATORY-GROUPS {
ibSmaNodeGroup
}
::= { ibSmaCompliances 1 }
ibSmaFullSwitchCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The full node implementation requirements for agents that
support the IPOIB SMA MIB for InfiniBand switches."
MODULE -- this module
MANDATORY-GROUPS {
ibSmaNodeGroup,
ibSmaSwitchGroup,
ibSmaGuidGroup,
ibSmaMgmtPortGroup,
ibSmaDataPortGroup,
ibSmaPKeyGroup,
ibSmaSlToVlMapGroup,
ibSmaVLArbitGroup,
ibSmaLFTGroup,
ibSmaRFTGroup,
ibSmaMFTGroup,
ibSmaSMGroup,
ibSmaVendDiagGroup,
ibSmaLedGroup,
ibSmaNotificationsGroup
}
::= { ibSmaCompliances 2 }
Expires November 2002 [Page 58]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaFullRouterCACompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The full node implementation requirements for agents that
support the IPOIB SMA MIB for InfiniBand CAs and routers."
MODULE -- this module
MANDATORY-GROUPS {
ibSmaNodeGroup,
ibSmaGuidGroup,
ibSmaMgmtPortGroup,
ibSmaDataPortGroup,
ibSmaPKeyGroup,
ibSmaSlToVlMapGroup,
ibSmaVLArbitGroup,
ibSmaSMGroup,
ibSmaVendDiagGroup,
ibSmaLedGroup,
ibSmaNotificationsGroup
}
::= { ibSmaCompliances 3 }
--****************************************************************
-- Units Of Conformance
--****************************************************************
ibSmaNodeGroup OBJECT-GROUP
OBJECTS {
ibSmaNodeString,
ibSmaNodeBaseVersion,
ibSmaNodeClassVersion,
ibSmaNodeType,
ibSmaNodeNumPorts,
ibSmaNodeGuid,
ibSmaNodePortGuid,
ibSmaNodePartitionTableNum,
ibSmaNodeDeviceId,
ibSmaNodeRevision,
ibSmaNodeLocalPortNumOrZero
ibSmaNodeVendorId,
ibSmaNodeTrapBuffer
}
STATUS current
DESCRIPTION
"The ibSmaNodeGroup defines the MIB objects that describe
this InfiniBand subnet node."
::= { ibSmaGroups 1 }
Expires November 2002 [Page 59]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaSwitchGroup OBJECT-GROUP
OBJECTS {
ibSmaSwLinearFdbTableNum,
ibSmaSwRandomFdbTableNum,
ibSmaSwMulticastFdbTableNum,
ibSmaSwLinearFdbTop,
ibSmaSwDefaultPort,
ibSmaSwDefMcastPriPort,
ibSmaSwDefMcastNotPriPort,
ibSmaSwLifeTimeValue,
ibSmaSwPortStateChange,
ibSmaSwLidsPerPort,
ibSmaSwPartitionEnforceNum,
ibSmaSwInboundEnforceCap,
ibSmaSwOutboundEnforceCap,
ibSmaSwFilterRawPktInputCap,
ibSmaSwFilterRawPktOutputCap
}
STATUS current
DESCRIPTION
"The ibSmaSwitchGroup defines the MIB objects that describe
this InfiniBand switch."
::= { ibSmaGroups 2 }
ibSmaGuidGroup OBJECT-GROUP
OBJECTS {
ibSmaGuidVal
}
STATUS current
DESCRIPTION
"The ibSmaGuidGroup defines the MIB object that describes
the GUIDs associated with this node.
::= { ibSmaGroups 3 }
Expires November 2002 [Page 60]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaMgmtPortGroup OBJECT-GROUP
OBJECTS {
ibSmaPortMKey,
ibSmaPortGidPrefix,
ibSmaPortLid,
ibSmaPortMasterSmLid,
ibSmaPortIsSubnetManager,
ibSmaPortIsNoticeSupported,
ibSmaPortIsTrapSupported,
ibSmaPortIsResetSupported,
ibSmaPortIsAutoMigrateSupported,
ibSmaPortIsSlMappingSupported,
ibSmaPortIsMKeyNvram,
ibSmaPortIsPKeyNvram,
ibSmaPortIsLedInfoSupported,
ibSmaPortIsSmDisabled,
ibSmaPortIsConnManageSupported,
ibSmaPortIsSnmpTunnelSupported,
ibSmaPortIsDevManageSupported,
ibSmaPortIsVendorClassSupported,
ibSmaPortGenericDiagCode,
ibSmaPortVendorDiagCode,
ibSmaPortMKeyLeasePeriod,
ibSmaPortMKeyProtectBits,
ibSmaPortMasterSmSl,
ibSmaPortMKeyViolations,
ibSmaPortPKeyViolations,
ibSmaPortQKeyViolations,
ibSmaPortNumGuid,
ibSmaPortSubnetTimeout,
ibSmaPortResponseTimeValue
}
STATUS current
DESCRIPTION
"The ibSmaMgmtPortGroup defines the MIB objects that describe
the management port."
::= { ibSmaGroups 4 }
Expires November 2002 [Page 61]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaDataPortGroup OBJECT-GROUP
OBJECTS {
ibSmaPortLinkWidthEnabled,
ibSmaPortLinkWidthSupported,
ibSmaPortLinkWidthActive,
ibSmaPortLinkSpeedSupported,
ibSmaPortLinkState,
ibSmaPortPhysState,
ibSmaPortLinkDownDefaultState,
ibSmaPortLinkSpeedActive,
ibSmaPortLinkSpeedEnabled,
ibSmaPortNeighborMtu,
ibSmaPortVirtLaneSupport,
ibSmaPortVlHighPriorityLimit,
ibSmaPortVlArbHighCapacity,
ibSmaPortVlArbLowCapacity,
ibSmaPortMtuCapacity,
ibSmaPortVlStallCount,
ibSmaPortHeadOfQueueLife,
ibSmaPortOperationalVls,
ibSmaPortPartEnforceInbound,
ibSmaPortPartEnforceOutbound,
ibSmaPortFilterRawPktInbound,
ibSmaPortFilterRawPktOutbound,
ibSmaPortLocalPhysError,
ibSmaPortOverrunError
}
STATUS current
DESCRIPTION
"The ibSmaDataPortGroup defines the MIB objects that describe
the IB data ports."
::= { ibSmaGroups 5 }
ibSmaPKeyGroup OBJECT-GROUP
OBJECTS {
ibSmaPKeyMembership,
ibSmaPKeyBase
}
STATUS current
DESCRIPTION
"The ibSmaPKeyGroup defines the MIB objects that describe
the Partition Keys."
::= { ibSmaGroups 6 }
ibSmaSlToVlMapGroup OBJECT-GROUP
OBJECTS {
ibSmaVirtualLane
}
STATUS current
DESCRIPTION
"The ibSmaSlToVlMapGroup defines the MIB objects that describe
the Service Level to Virtual Lane mapping."
::= { ibSmaGroups 7 }
Expires November 2002 [Page 62]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaVLArbitGroup OBJECT-GROUP
OBJECTS {
ibSmaHiPriVirtLane,
ibSmaHiPriWeight,
ibSmaLowPriVirtLane,
ibSmaLowPriWeight
}
STATUS current
DESCRIPTION
"The ibSmaVLArbitGroup defines the MIB objects that describe
the Virtual Lane High and Low Arbitrations."
::= { ibSmaGroups 8 }
ibSmaLFTGroup OBJECT-GROUP
OBJECTS {
ibSmaLinForwEgressPort
}
STATUS current
DESCRIPTION
"The ibSmaLFTGroup defines the MIB objects that describe
the Linear Forwarding Table."
::= { ibSmaGroups 9 }
ibSmaRFTGroup OBJECT-GROUP
OBJECTS {
ibSmaRandomDestLID,
ibSmaRandomForwEgressPort,
ibSmaRandomLMC,
ibSmaRandomIsValid
}
STATUS current
DESCRIPTION
"The ibSmaRFTGroup defines the MIB objects that describe
the Random Forwarding Table."
::= { ibSmaGroups 10 }
ibSmaMFTGroup OBJECT-GROUP
OBJECTS {
ibSmaMulForwMask
}
STATUS current
DESCRIPTION
"The ibSmaMFTGroup defines the MIB objects that describe
the Multicast Forwarding Table."
::= { ibSmaGroups 11 }
Expires November 2002 [Page 63]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaSMGroup OBJECT-GROUP
OBJECTS {
ibSmaSmGuid,
ibSmaSmSmKey,
ibSmaSmSmpCount,
ibSmaSmPriority,
ibSmaSmState
}
STATUS current
DESCRIPTION
"The ibSmaSMGroup defines the MIB objects that describe
the Subnet Manager Information Table."
::= { ibSmaGroups 12 }
ibSmaVendDiagGroup OBJECT-GROUP
OBJECTS {
ibSmaPortGenericDiagCode,
ibSmaPortVendorDiagCode,
ibSmaPortVendorDiagIndexFwd,
ibSmaPortVendorDiagData
}
STATUS current
DESCRIPTION
"The ibSmaVendDiagGroup defines the MIB objects that describe
the vendor diagnostics table."
::= { ibSmaGroups 13 }
ibSmaLedGroup OBJECT-GROUP
OBJECTS {
ibSmaLedState
}
STATUS current
DESCRIPTION
"The ibSmaSMGroup defines the MIB objects that describe
the LED table."
::= { ibSmaGroups 14 }
Expires November 2002 [Page 64]
Internet Draft IPOVERIB SMA MIB May 2002
ibSmaNotificationsGroup NOTIFICATION-GROUP
NOTIFICATIONS {
ibSmaPortNowInService,
ibSmaPortOutOfService,
ibSmaPortLinkStateChange,
ibSmaLinkIntegrityThresReached,
ibSmaExcessBuffOverrunThres,
ibSmaFlowCntrlUpdateTimerExpire,
ibSmaBadManagementKey,
ibSmaBadPartitionKey,
ibSmaBadQueueKey
}
STATUS current
DESCRIPTION
"The notifications that an IPOIB SNMP agent transmits
on the behalf of the SMA Trap message implementation."
::= { ibSmaGroups 15 }
END
6.0 Revision History
This section should be removed when this document is published as an
RFC.
6.1 Changes from <draft-ietf-ipoib-subnet-mgmt-agent-mib-00.txt>
Added Section 7.0 Revision History to keep track of updates to the MIB.
Sean Harnedy from InfiniSwitch Corporation was added as an author.
Title of the ID was changed to "Definitions of Managed Objects for
the Infiniband Subnet Management Agent (SMA)".
Updated the MODULE-IDENTITY changed the name to ibSmaMib.
The Textual Convention macros were removed from the document and the
current IPOIB TC MIB containing the definitions was IMPORTed.
Throughout the MIB the sma prefix was replaced with ibSma to align with
IPOIB MIB object naming convention.
The IPOIB SMA MIB Definitions were expanded to 14 MIB groups to cover the
full SMA attribute management set. The REFERENCE clause was added to each
object for cross-reference to the IBTA specification [IBTAArch].
Action items in former section 7. Next Steps were addressed, and this
section was removed. Added Section 4. Structure of the MIB that contains
descriptive text giving an overview of the various groups in the MIB.
Section 8. Security Considerations was updated. The Compliance macros
were added to the MIB. Textual Conventions are now IMPORTed from the
IPOIB Textual Convention MIB. The MIB was assigned the appropriate OID
in the SNMP naming hierarchy.
Expires November 2002 [Page 65]
Internet Draft IPOVERIB SMA MIB May 2002
Updated Table of Contents, section numbering, and other minor edits
as needed.
6.2 Changes from <draft-ietf-ipoib-subnet-mgmt-agent-mib-01.txt>
Updated author information for Bill Swortwood. Corrected INDEX clause for
the ibSmaGuidInfoEntry. Updated for new TCs. Fixed minor bugs, updated
DESCRIPTION, etc.
7. Security Considerations
SNMPv1 by itself is not a secure environment. Even if the network
itself is secure (for example by using IPSec), even then, there is no
control as to who on the secure network is allowed to access and
GET/SET (read/change/create/delete) the objects in this MIB.
It is recommended that the implementers consider the security
features as provided by the SNMPv3 framework. Specifically, the use
of the User-based Security Model RFC 2574 [RFC2574] and the View-
based Access Control Model RFC 2575 [RFC2575] is recommended.
It is then a customer/user responsibility to ensure that the SNMP
entity giving access to an instance of this MIB, is properly configured
to give access to the objects only to those principals (users) that
have legitimate rights to indeed GET or SET (change/create/delete) them.
8. Acknowledgements
The author [Bill Swortwood] would like to acknowledge Anne Marie
Merritt who authored the VIA MIB which this document [-00] was based on.
9. Intellectual Property
The IETF takes no position regarding the validity or scope of any
intellectual property or other rights that might be claimed to
pertain to the implementation or use of the technology described
in this document or the extent to which any license under such
rights might or might not be available; neither does it
represent that it has made any effort to identify any such
rights. Information on the IETF's procedures with respect to
rights in standards-track and standards-related documentation
can be found in BCP-11. Copies of claims of rights made
available for publication and any assurances of licenses to be
made available, or the result of an attempt made to obtain a
general license or permission for the use of such proprietary
rights by implementors or users of this specification can be
obtained from the IETF Secretariat.
The IETF invites any interested party to bring to its attention
any copyrights, patents or patent applications, or other
proprietary rights which may cover technology that may be required
to practice this standard. Please address the information to the
IETF Executive Director.
Expires November 2002 [Page 66]
Internet Draft IPOVERIB SMA MIB May 2002
10. References
[RFC2571] Harrington, D., Presuhn, R. and B. Wijnen, "An
Architecture for Describing SNMP Management Frameworks",
RFC 2571, April 1999.
[RFC1155] Rose, M. and K. McCloghrie, "Structure and Identification
of Management Information for TCP/IP-based Internets", STD
16, RFC 1155, May 1990.
[RFC1212] Rose, M. and K. McCloghrie, "Concise MIB Definitions", STD
16, RFC 1212, March 1991.
[RFC1215] Rose, M., "A Convention for Defining Traps for use with
the SNMP", RFC 1215, March 1991.
[RFC2578] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
Rose, M. and S. Waldbusser, "Structure of Management
Information Version 2 (SMIv2)", STD 58, RFC 2578, April
1999.
[RFC2579] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
Rose, M. and S. Waldbusser, "Textual Conventions for
SMIv2", STD 58, RFC 2579, April 1999.
[RFC2580] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
Rose, M. and S. Waldbusser, "Conformance Statements for
SMIv2", STD 58, RFC 2580, April 1999.
[RFC1157] Case, J., Fedor, M., Schoffstall, M. and J. Davin, "Simple
Network Management Protocol", STD 15, RFC 1157, May 1990.
[RFC1901] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser,
"Introduction to Community-based SNMPv2", RFC 1901,
January 1996.
[RFC1906] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser,
"Transport Mappings for Version 2 of the Simple Network
Management Protocol (SNMPv2)", RFC 1906, January 1996.
[RFC2572] Case, J., Harrington D., Presuhn R. and B. Wijnen,
"Message Processing and Dispatching for the Simple Network
Management Protocol (SNMP)", RFC 2572, April 1999.
[RFC2574] Blumenthal, U. and B. Wijnen, "User-based Security Model
(USM) for version 3 of the Simple Network Management
Protocol (SNMPv3)", RFC 2574, April 1999.
[RFC1905] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser,
"Protocol Operations for Version 2 of the Simple Network
Management Protocol (SNMPv2)", RFC 1905, January 1996.
Expires November 2002 [Page 67]
Internet Draft IPOVERIB SMA MIB May 2002
[RFC2573] Levi, D., Meyer, P. and B. Stewart, "SNMPv3 Applications",
RFC 2573, April 1999.
[RFC2575] Wijnen, B., Presuhn, R. and K. McCloghrie, "View-based
Access Control Model (VACM) for the Simple Network
Management Protocol (SNMP)", RFC 2575, April 1999.
[RFC2570] Case, J., Mundy, R., Partain, D. and B. Stewart,
"Introduction to Version 3 of the Internet-standard
Network Management Framework", RFC 2570, April 1999.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[IBTAArch] Infiniband Trade Association, Infiniband(TM)
Architecture Specification Vol 1&2 Release 1.0a, 1999,
2000.
[IBIF] Anderson, B., and S. Harnedy, "Definition of Managed Objects
Infiniband Interface Types" <draft-ietf-ipoib-ibif-mib-02.txt>,
May 2002.
[IBTC] Harnedy, S., "Definitions of Textual Conventions and OBJECT-
IDENTITIES for IP Over InfiniBand (IPOVERIB) Management"
<draft-ietf-ipoib-ibmib-tc-mib-01.txt>. May 2002.
11. Authors' Addresses
Bill Swortwood
Omegaband Incorporated
9020-I Capital of Texas Highway North
Austin, TX 78759 Phone: 1-512-401-8208
USA Email: billiam@omegaband.com
Sean Harnedy
InfiniSwitch Corporation
134 Flanders Road Phone: 1-508-599-6388
Westborough, MA 01581 Email: sharnedy@infiniswitch.com
USA
Expires November 2002 [Page 68]
