Internet Engineering Task Force R. Geib, Ed.
Internet-Draft Deutsche Telekom
Intended status: Standards Track A. Morton
Expires: January 3, 2011 AT&T Labs
R. Fardid
Cariden Technologies
A. Steinmitz
HS Fulda
July 2, 2010
IPPM standard advancement testing
draft-ietf-ippm-metrictest-00
Abstract
This document specifies tests to determine if multiple independent
instantiations of a performance metric RFC have implemented the
specifications in the same way. This is the performance metric
equivalent of interoperability, required to advance RFCs along the
standards track. Results from different implementations of metric
RFCs will be collected under the same underlying network conditions
and compared using state of the art statistical methods. The goal is
an evaluation of the metric RFC itself, whether its definitions are
clear and unambiguous to implementors and therefore a candidate for
advancement on the IETF standards track.
Status of this Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on January 3, 2011.
Copyright Notice
Copyright (c) 2010 IETF Trust and the persons identified as the
document authors. All rights reserved.
Geib, et al. Expires January 3, 2011 [Page 1]
Internet-Draft IPPM standard advancement testing July 2010
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1. Requirements Language . . . . . . . . . . . . . . . . . . 6
2. Basic idea . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3. Verification of conformance to a metric specification . . . . 8
3.1. Tests of an individual implementation against a metric
specification . . . . . . . . . . . . . . . . . . . . . . 8
3.2. Test setup resulting in identical live network testing
conditions . . . . . . . . . . . . . . . . . . . . . . . . 9
3.3. Tests of two or more different implementations against
a metric specification . . . . . . . . . . . . . . . . . . 14
3.4. Clock synchronisation . . . . . . . . . . . . . . . . . . 14
3.5. Recommended Metric Verification Measurement Process . . . 15
3.6. Miscellaneous . . . . . . . . . . . . . . . . . . . . . . 19
4. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 19
5. Contributors . . . . . . . . . . . . . . . . . . . . . . . . . 19
6. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 20
7. Security Considerations . . . . . . . . . . . . . . . . . . . 20
8. References . . . . . . . . . . . . . . . . . . . . . . . . . . 20
8.1. Normative References . . . . . . . . . . . . . . . . . . . 20
8.2. Informative References . . . . . . . . . . . . . . . . . . 21
Appendix A. An example on a One-way Delay metric validation . . . 22
A.1. Compliance to Metric specification requirements . . . . . 22
A.2. Examples related to statistical tests for One-way Delay . 24
Appendix B. Anderson-Darling 2 sample C++ code . . . . . . . . . 25
Appendix C. Glossary . . . . . . . . . . . . . . . . . . . . . . 34
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 35
Geib, et al. Expires January 3, 2011 [Page 2]
Internet-Draft IPPM standard advancement testing July 2010
1. Introduction
The Internet Standards Process RFC2026 [RFC2026] requires that for a
IETF specification to advance beyond the Proposed Standard level, at
least two genetically unrelated implementations must be shown to
interoperate correctly with all features and options. This
requirement can be met by supplying:
o evidence that (at least a sub-set of) the specification has been
implemented by multiple parties, thus indicating adoption by the
IETF community and the extent of feature coverage.
o evidence that each feature of the specification is sufficiently
well-described to support interoperability, as demonstrated
through testing and/or user experience with deployment.
In the case of a protocol specification, the notion of
"interoperability" is reasonably intuitive - the implementations must
successfully "talk to each other", while exercising all features and
options. To achieve interoperability, two implementors need to
interpret the protocol specifications in equivalent ways. In the
case of IP Performance Metrics (IPPM), this definition of
interoperability is only useful for test and control protocols like
the One-Way Active Measurement Protocol, OWAMP [RFC4656], and the
Two-Way Active Measurement Protocol, TWAMP [RFC5357].
A metric specification RFC describes one or more metric definitions,
methods of measurement and a way to report the results of
measurement. One example would be a way to test and report the One-
way Delay that data packets incur while being sent from one network
location to another, One-way Delay Metric.
In the case of metric specifications, the conditions that satisfy the
"interoperability" requirement are less obvious, and there was a need
for IETF agreement on practices to judge metric specification
"interoperability" in the context of the IETF Standards Process.
This memo provides methods which should be suitable to evaluate
metric specifications for standards track advancement. The methods
proposed here MAY be generally applicable to metric specification
RFCs beyond those developed under the IPPM Framework [RFC2330].
Since many implementations of IP metrics are embedded in measurement
systems that do not interact with one another (they were built before
OWAMP and TWAMP), the interoperability evaluation called for in the
IETF standards process cannot be determined by observing that
independent implementations interact properly for various protocol
exchanges. Instead, verifying that different implementations give
statistically equivalent results under controlled measurement
Geib, et al. Expires January 3, 2011 [Page 3]
Internet-Draft IPPM standard advancement testing July 2010
conditions takes the place of interoperability observations. Even
when evaluating OWAMP and TWAMP RFCs for standards track advancement,
the methods described here are useful to evaluate the measurement
results because their validity would not be ascertained in typical
interoperability testing.
The standards advancement process aims at producing confidence that
the metric definitions and supporting material are clearly worded and
unambiguous, or reveals ways in which the metric definitions can be
revised to achieve clarity. The process also permits identification
of options that were not implemented, so that they can be removed
from the advancing specification. Thus, the product of this process
is information about the metric specification RFC itself:
determination of the specifications or definitions that are clear and
unambiguous and those that are not (as opposed to an evaluation of
the implementations which assist in the process).
This document defines a process to verify that implementations (or
practically, measurement systems) have interpreted the metric
specifications in equivalent ways, and produce equivalent results.
Testing for statistical equivalence requires ensuring identical test
setups (or awareness of differences) to the best possible extent.
Thus, producing identical test conditions is a core goal of the memo.
Another important aspect of this process is to test individual
implementations against specific requirements in the metric
specifications using customized tests for each requirement. These
tests can distinguish equivalent interpretations of each specific
requirement.
Conclusions on equivalence are reached by two measures.
First, implementations are compared against individual metric
specifications to make sure that differences in implementation are
minimised or at least known.
Second, a test setup is proposed ensuring identical networking
conditions so that unknowns are minimized and comparisons are
simplified. The resulting separate data sets may be seen as samples
taken from the same underlying distribution. Using state of the art
statistical methods, the equivalence of the results is verified. To
illustrate application of the process and methods defined here,
evaluation of the One-way Delay Metric [RFC2679] is provided in an
Appendix. While test setups will vary with the metrics to be
validated, the general methodology of determining equivalent results
will not. Documents defining test setups to evaluate other metrics
should be developed once the process proposed here has been agreed
and approved.
Geib, et al. Expires January 3, 2011 [Page 4]
Internet-Draft IPPM standard advancement testing July 2010
The metric RFC advancement process begins with a request for protocol
action accompanied by a memo that documents the supporting tests and
results. The procedures of [RFC2026] are expanded in[RFC5657],
including sample implementation and interoperability reports.
Section 3 of [morton-advance-metrics-01] can serve as a template for
a metric RFC report which accompanies the protocol action request to
the Area Director, including description of the test set-up,
procedures, results for each implementation and conclusions.
Changes from prior ID -02 to WG -00 draft
o Incorporation of aspects of reporting to support the protocol
action request in the Introduction and section 3.5
o Overhaul of sectcion 3.2 regarding tunneling: Added generic
tunneling requirements and L2TPv3 as an example tunneling
mechanism fulfilling the tunneling requirements. Removed and
adapted some of the prior references to other tunneling protocols
o Softened a requirement within section 3.4 (MUST to SHOULD on
precision) and removed some comments of the authors.
o Updated contact information of one author and added a new author.
o Added example C++ code of an Anderson-Darling two sample test
implementation.
Changes from ID -01 to ID -02 version
o Major editorial review, rewording and clarifications on all
contents.
o Additional text on parrallel testing using VLANs and GRE or
Pseudowire tunnels.
o Additional examples and a glossary.
Changes from ID -00 to ID -01 version
o Addition of a comparison of individual metric implementations
against the metric specification (trying to pick up problems and
solutions for metric advancement [morton-advance-metrics]).
o More emphasis on the requirement to carefully design and document
the measurement setup of the metric comparison.
o Proposal of testing conditions under identical WAN network
conditions using IP in IP tunneling or Pseudo Wires and parallel
Geib, et al. Expires January 3, 2011 [Page 5]
Internet-Draft IPPM standard advancement testing July 2010
measurement streams.
o Proposing the requirement to document the smallest resolution at
which an ADK test was passed by 95%. As no minimum resolution is
specified, IPPM metric compliance is not linked to a particular
performance of an implementation.
o Reference to RFC 2330 and RFC 2679 for the 95% confidence interval
as preferred criterion to decide on statistical equivalence
o Reducing the proposed statistical test to ADK with 95% confidence.
1.1. Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
2. Basic idea
The implementation of a standard compliant metric is expected to meet
the requirements of the related metric specification. So before
comparing two metric implementations, each metric implementation is
individually compared against the metric specification.
Most metric specifications leave freedom to implementors on non-
fundamental aspects of an individual metric (or options). Comparing
different measurement results using a statistical test with the
assumption of identical test path and testing conditions requires
knowledge of all differences in the overall test setup. Metric
specification options chosen by implementors have to be documented.
It is REQUIRED to use identical implementation options wherever
possible for any test proposed here. Calibrations proposed by metric
standards should be performed to further identify (and possibly
reduce) potential sources of errors in the test setup.
The Framework for IP Performance Metrics [RFC2330] expects that a
"methodology for a metric should have the property that it is
repeatable: if the methodology is used multiple times under identical
conditions, it should result in consistent measurements." This means
an implementation is expected to repeatedly measure a metric with
consistent results (repeatability with the same result). Small
deviations in the test setup are expected to lead to small deviations
in results only. To characterise statistical equivalence in the case
of small deviations, RFC 2330 and [RFC2679] suggest to apply a 95%
confidence interval. Quoting RFC 2679, "95 percent was chosen
because ... a particular confidence level should be specified so that
Geib, et al. Expires January 3, 2011 [Page 6]
Internet-Draft IPPM standard advancement testing July 2010
the results of independent implementations can be compared."
Two different implementations are expected to produce statistically
equivalent results if they both measure a metric under the same
networking conditions. Formulating in statistical terms: separate
metric implementations collect separate samples from the same
underlying statistical process (the same network conditions). The
statistical hypothesis to be tested is the expectation that both
samples do not expose statistically different properties. This
requires careful test design:
o The measurement test setup must be self-consistent to the largest
possible extent. To minimize the influence of the test and
measurement setup on the result, network conditions and paths MUST
be identical for the compared implementations to the largest
possible degree. This includes both the stability and non-
ambiguity of routes taken by the measurement packets. See RFC
2330 for a discussion on self-consistency.
o The error induced by the sample size must be small enough to
minimize its influence on the test result. This may have to be
respected, especially if two implementations measure with
different average probing rates.
o Every comparison must be repeated several times based on different
measurement data to avoid random indications of compatibility (or
the lack of it).
o To minimize the influence of implementation options on the result,
metric implementations SHOULD use identical options and parameters
for the metric under evaluation.
o The implementation with the lowest probing frequency determines
the smallest temporal interval for which samples can be compared.
The metric specifications themselves are the primary focus of
evaluation, rather than the implementations of metrics. The
documentation produced by the advancement process should identify
which metric definitions and supporting material were found to be
clearly worded and unambiguous, OR, it should identify ways in which
the metric specification text should be revised to achieve clarity
and unified interpretation.
The process should also permit identification of options that were
not implemented, so that they can be removed from the advancing
specification (this is an aspect more typical of protocol advancement
along the standards track).
Geib, et al. Expires January 3, 2011 [Page 7]
Internet-Draft IPPM standard advancement testing July 2010
Note that this document does not propose to base interoperability
indications of performance metric implementations on comparisons of
individual singletons. Individual singletons may be impacted by many
statistical effects while they are measured. Comparing two
singletons of different implementations may result in failures with
higher probability than comparing samples.
3. Verification of conformance to a metric specification
This section specifies how to verify compliance of two or more IPPM
implementations against a metric specification. This document only
proposes a general methodology. Compliance criteria to a specific
metric implementation need to be defined for each individual metric
specification. The only exception is the statistical test comparing
two metric implementations which are simultaneously tested. This
test is applicable without metric specific decision criteria.
3.1. Tests of an individual implementation against a metric
specification
A metric implementation MUST support the requirements classified as
"MUST" and "REQUIRED" of the related metric specification to be
compliant to the latter.
Further, supported options of a metric implementation SHOULD be
documented in sufficient detail. The documentation of chosen options
is RECOMMENDED to minimise (and recognise) differences in the test
setup if two metric implementations are compared. Further, this
documentation is used to validate and improve the underlying metric
specification option, to remove options which saw no implementation
or which are badly specified from the metric specification to be
promoted to a standard. This documentation SHOULD be made for all
implementation relevant specifications of a metric picked for a
comparison, which aren't explicitly marked as "MUST" or "REQUIRED" in
the metric specification. This applies for the following sections of
all metric specifications:
o Singleton Definition of the Metric.
o Sample Definition of the Metric.
o Statistics Definition of the Metric. As statistics are compared
by the test specified here, this documentation is required even in
the case, that the metric specification does not contain a
Statistics Definition.
Geib, et al. Expires January 3, 2011 [Page 8]
Internet-Draft IPPM standard advancement testing July 2010
o Timing and Synchronisation related specification (if relevant for
the Metric).
o Any other technical part present or missing in the metric
specification, which is relevant for the implementation of the
Metric.
RFC2330 and RFC2679 emphasise precision as an aim of IPPM metric
implementations. A single IPPM conformant implementation MUST under
otherwise identical network conditions produce precise results for
repeated measurements of the same metric.
RFC 2330 prefers the "empirical distribution function" EDF to
describe collections of measurements. RFC 2330 determines, that
"unless otherwise stated, IPPM goodness-of-fit tests are done using
5% significance." The goodness of fit test determines by which
precision two or more samples of a metric implementation belong to
the same underlying distribution (of measured network performance
events). The goodness of fit test to be applied is the Anderson-
Darling K sample test (ADK sample test, K stands for the number of
samples to be compared) [ADK]. Please note that RFC 2330 and RFC
2679 apply an Anderson Darling goodness of fit test too.
The results of a repeated test with a single implementation MUST pass
an ADK sample test with confidence level of 95%. The resolution for
which the ADK test has been passed with the specified confidence
level MUST be documented. To formulate this differently: The
requirement is to document the smallest resolution, at which the
results of the tested metric implementation pass an ADK test with a
confidence level of 95%. The minimum resolution available in the
reported results from each implementation MUST be taken into account
in the ADK test.
3.2. Test setup resulting in identical live network testing conditions
Two major issues complicate tests for metric compliance across live
networks under identical testing conditions. One is the general
point that metric definition implementations cannot be conveniently
examined in field measurement scenarios. The other one is more
broadly described as "parallelism in devices and networks", including
mechanisms like those that achieve load balancing (see [RFC4928]).
This section proposes two measures to deal with both issues.
Tunneling mechanisms can be used to avoid parallel processing of
different flows in the network. Measuring by separate parallel probe
flows results in repeated collection of data. If both measures are
combined, WAN network conditions are identical for a number of
independent measurement flows, no matter what the network conditions
Geib, et al. Expires January 3, 2011 [Page 9]
Internet-Draft IPPM standard advancement testing July 2010
are in detail.
Any measurement setup MUST be made to avoid the probing traffic
itself to impede the metric measurement. The created measurement
load MUST NOT result in congestion at the access link connecting the
measurement implementation to the WAN. The created measurement load
MUST NOT overload the measurement implementation itself, eg. by
causing a high CPU load or by creating imprecisions due to internal
transmit (receive respectively) probe packet collisions.
Tunneling multiple flows reaching a network element on a single
physical port may allow to transmit all packets of the tunnel via the
same path. Applying tunnels to avoid undesired influence of standard
routing for measurement purposes is a concept known from literature,
see e.g. GRE encapsulated multicast probing [GU+Duffield]. An
existing IP in IP tunnel protocol can be applied to avoid Equal-Cost
Multi-Path (ECMP) routing of different measurement streams if it
meets the following criteria:
o Inner IP packets from different measurement implementations are
mapped into a single tunnel with single outer IP origin and
destination address as well as origing and destination port
numbers which are identical for all packets.
o An easily accessible commodity tunneling protocol allows to carry
out a metric test from more test sites.
o A low operational overhead may enable a broader audience to set up
a metric test with the desired properties.
o The tunneling protocol should be reliable and stable in set up and
operation to avoid disturbances or influence on the test results.
o The tunneling protocol should not incurr any extra cost for those
interested in setting up a metric test.
An illustration of a test setup with two tunnels and two flows
between two linecards of one implementation is given in Figure 1.
Geib, et al. Expires January 3, 2011 [Page 10]
Internet-Draft IPPM standard advancement testing July 2010
Implementation ,---. +--------+
+~~~~~~~~~~~/ \~~~~~~| Remote |
+------->-----F2->-| / \ |->---+ |
| +---------+ | Tunnel 1( ) | | |
| | transmit|-F1->-| ( ) |->+ | |
| | LC1 | +~~~~~~~~~| |~~~~| | | |
| | receive |-<--+ ( ) | F1 F2 |
| +---------+ | |Internet | | | | |
*-------<-----+ F2 | | | | | |
+---------+ | | +~~~~~~~~~| |~~~~| | | |
| transmit|-* *-| | | |--+<-* |
| LC2 | | Tunnel 2( ) | | |
| receive |-<-F1-| \ / |<-* |
+---------+ +~~~~~~~~~~~\ /~~~~~~| Router |
`-+-' +--------+
Illustration of a test setup with two tunnels. For simplicity, only
two linecards of one implementation and two flows F between them are
shown.
Figure 1
Figure 2 shows the network elements required to set up GRE tunnels or
as shown by figure 1.
Implementation
+-----+ ,---.
| LC1 | / \
+-----+ / \ +------+
| +-------+ ( ) +-------+ |Remote|
+--------+ | | | | | | | |
|Ethernet| | Tunnel| |Internet | | Tunnel| | |
|Switch |--| Head |--| |--| Head |--| |
+--------+ | Router| | | | Router| | |
| | | ( ) | | |Router|
+-----+ +-------+ \ / +-------+ +------+
| LC2 | \ /
+-----+ `-+-'
Illustration of a hardware setup to realise the test setup
illustrated by figure 1 with GRE tunnels or Pseudowires.
Figure 2
If tunneling is applied, two tunnels MUST carry all test traffic in
between the test site and the remote site. For example, if 802.1Q
Geib, et al. Expires January 3, 2011 [Page 11]
Internet-Draft IPPM standard advancement testing July 2010
Ethernet Virtual LANs (VLAN) are applied and the measurement streams
are carried in different VLANs, the IP tunnel or Pseudo Wires
respectively MUST be set up in physical port mode to avoid set up of
Pseudo Wires per VLAN (which may see different paths due to ECMP
routing), see RFC 4448. The remote router and the Ethernet switch
shown in figure 2 must support 802.1Q in this set up.
The IP packet size of the metric implementation SHOULD be chosen
small enough to avoid fragmentation due to the added Ethernet and
tunnel headers. Otherwise, the impact of tunnel overhead on
fragmentation and interface MTU size MUST be understood and taken
into account (see [RFC4459]).
An Ethernet port mode IP tunnel carrying several 802.1Q VLANs each
containing measurement traffic of a single measurement system was set
up as a proof of concept using RFC4719 [RFC4719], Transport of
Ethernet Frames over L2TPv3. Ethernet over L2TPv3 seems to fulfill
most of the desired tunneling protocol criteria mentioned above.
The following headers may have to be accounted for when calculating
total packet length, if VLANs and Ethernet over L2TPv3 tunnels are
applied:
o Ethernet 802.1Q: 22 Byte.
o L2TPv3 Header: 4-16 Byte for L2TPv3 data messages over IP; 16-28
Byte for L2TPv3 data messages over UDP.
o IPv4 Header (outer IP header): 20 Byte.
o MPLS Labels may be added by a carrier. Each MPLS Label has a
length of 4 Bytes. By the time of writing, between 1 and 4 Labels
seems to be a fair guess of what's expectable.
The applicability of one or more of the following tunneling protocols
may be investigated by interested parties if Ethernet over L2TPv3 is
felt to be not suitable: IP in IP [RFC2003] or Generic Routing
Encapsulation (GRE) [RFC2784]. RFC 4928 [RFC4928] proposes measures
how to avoid ECMP treatment in MPLS networks.
L2TP is a commodity tunneling protocol [RFC2661]. By the time of
writing, L2TPv3 [RFC3931]is the latest version of L2TP.
Ethernet Pseudo Wires may also be set up on MPLS networks [RFC4448].
While there's no technical issue with this solution, MPLS interfaces
are mostly found in the network provider domain. Hence not all of
the above tunneling criteria are met.
Geib, et al. Expires January 3, 2011 [Page 12]
Internet-Draft IPPM standard advancement testing July 2010
Each test is repeated several times. WAN conditions may change over
time. Sequential testing is desirable, but may not be a useful
metric test option. It is RECOMMENDED that tests be carried out by
establishing N different parallel measurement flows. Two or three
linecards per implementation serving to send or receive measurement
flows should be sufficient to create 5 or more parallel measurement
flows. If three linecards are used, each card sends and receives 2
flows. Other options are to separate flows by DiffServ marks
(without deploying any QoS in the inner or outer tunnel) or using a
single CBR flow and evaluating every n-th singleton to belong to a
specific measurement flow.
Some additional rules to calculate and compare samples have to be
respected to perform a metric test:
o To compare different probes of a common underlying distribution in
terms of metrics characterising a communication network requires
to respect the temporal nature for which the assumption of common
underlying distribution may hold. Any singletons or samples to be
compared MUST be captured within the same time interval.
o Whenever statistical events like singletons or rates are used to
characterise measured metrics of a time-interval, at least 5
singletons of a relevant metric SHOULD be present to ensure a
minimum confidence into the reported value (see Wikipedia on
confidence [Rule of thumb]). Note that this criterion also is to
be respected e.g. when comparing packet loss metrics. Any packet
loss measurement interval to be compared with the results of
another implementation SHOULD contain at least five lost packets
to have a minimum confidence that the observed loss rate wasn't
caused by a small number of random packet drops.
o The minimum number of singletons or samples to be compared by an
Anderson-Darling test SHOULD be 100 per tested metric
implementation. Note that the Anderson-Darling test detects small
differences in distributions fairly well and will fail for high
number of compared results (RFC2330 mentions an example with 8192
measurements where an Anderson-Darling test always failed).
o Generally, the Anderson-Darling test is sensitive to differences
in the accuracy or bias associated with varying implementations or
test conditions. These dissimilarities may result in differing
averages of samples to be compared. An example may be different
packet sizes, resulting in a constant delay difference between
compared samples. Therefore samples to be compared by an Anderson
Darling test MAY be calibrated by the difference of the average
values of the samples. Any calibration of this kind MUST be
documented in the test result.
Geib, et al. Expires January 3, 2011 [Page 13]
Internet-Draft IPPM standard advancement testing July 2010
3.3. Tests of two or more different implementations against a metric
specification
RFC2330 expects "a methodology for a given metric [to] exhibit
continuity if, for small variations in conditions, it results in
small variations in the resulting measurements. Slightly more
precisely, for every positive epsilon, there exists a positive delta,
such that if two sets of conditions are within delta of each other,
then the resulting measurements will be within epsilon of each
other." A small variation in conditions in the context of the metric
test proposed here can be seen as different implementations measuring
the same metric along the same path.
IPPM metric specification however allow for implementor options to
the largest possible degree. It can't be expected that two
implementors pick identical options for the implementations.
Implementors SHOULD to the highest degree possible pick the same
configurations for their systems when comparing their implementations
by a metric test.
In some cases, a goodness of fit test may not be possible or show
disappointing results. To clarify the difficulties arising from
different implementation options, the individual options picked for
every compared implementation SHOULD be documented in sufficient
detail. Based on this documentation, the underlying metric
specification should be improved before it is promoted to a standard.
The same statistical test as applicable to quantify precision of a
single metric implementation MUST be passed to compare metric
conformance of different implementations. To document compatibility,
the smallest measurement resolution at which the compared
implementations passed the ADK sample test MUST be documented.
For different implementations of the same metric, "variations in
conditions" are reasonably expected. The ADK test comparing samples
of the different implementations may result in a lower precision than
the test for precision of each implementation individually.
3.4. Clock synchronisation
Clock synchronization effects require special attention. Accuracy of
one-way active delay measurements for any metrics implementation
depends on clock synchronization between the source and destination
of tests. Ideally, one-way active delay measurement (RFC 2679,
[RFC2679]) test endpoints either have direct access to independent
GPS or CDMA-based time sources or indirect access to nearby NTP
primary (stratum 1) time sources, equipped with GPS receivers.
Access to these time sources may not be available at all test
Geib, et al. Expires January 3, 2011 [Page 14]
Internet-Draft IPPM standard advancement testing July 2010
locations associated with different Internet paths, for a variety of
reasons out of scope of this document.
When secondary (stratum 2 and above) time sources are used with NTP
running across the same network, whose metrics are subject to
comparative implementation tests, network impairments can affect
clock synchronization, distort sample one-way values and their
interval statistics. It is RECOMMENDED to discard sample one-way
delay values for any implementation, when one of the following
reliability conditions is met:
o Delay is measured and is finite in one direction, but not the
other.
o Absolute value of the difference between the sum of one-way
measurements in both directions and round-trip measurement is
greater than X% of the latter value.
Examination of the second condition requires RTT measurement for
reference, e.g., based on TWAMP (RFC5357, RFC 5357 [RFC5357]), in
conjunction with one-way delay measurement.
Specification of X% to strike a balance between identification of
unreliable one-way delay samples and misidentification of reliable
samples under a wide range of Internet path RTTs probably requires
further study.
An IPPM compliant metric implementation whose measurement requires
synchronized clocks is however expected to provide precise
measurement results. Any IPPM metric implementation SHOULD be of a
precision of 1 ms (+/- 500 us) with a confidence of 95% if the metric
is captured along an Internet path which is stable and not congested
during a measurement duration of an hour or more.
3.5. Recommended Metric Verification Measurement Process
In order to meet their obligations under the IETF Standards Process
the IESG must be convinced that each metric specification advanced to
Draft Standard or Internet Standard status is clearly written, that
there are the required multiple verifiably equivalent
implementations, and that all options have been implemented.
In the context of this document, metrics are designed to measure some
characteristic of a data network. An aim of any metric definition
should be that it should be specified in a way that can reliably
measure the specific characteristic in a repeatable way.
Each metric, statistic or option of those to be validated MUST be
Geib, et al. Expires January 3, 2011 [Page 15]
Internet-Draft IPPM standard advancement testing July 2010
compared against a reference measurement or another implementation by
at least 5 different basic data sets, each one with sufficient size
to reach the specified level of confidence, as specified by this
document.
Finally, the metric definitions, embodied in the text of the RFCs,
are the objects that require evaluation and possible revision in
order to advance to the next step on the standards track.
IF two (or more) implementations do not measure an equivalent metric
as specified by this document,
AND sources of measurement error do not adequately explain the lack
of agreement,
THEN the details of each implementation should be audited along with
the exact definition text, to determine if there is a lack of clarity
that has caused the implementations to vary in a way that affects the
correspondence of the results.
IF there was a lack of clarity or multiple legitimate interpretations
of the definition text,
THEN the text should be modified and the resulting memo proposed for
consensus and advancement along the standards track.
Finally, all the findings MUST be documented in a report that can
support advancement on the standards track, similar to those
described in [RFC5657]. The list of measurement devices used in
testing satisfies the implementation requirement, while the test
results provide information on the quality of each specification in
the metric RFC (the surrogate for feature interoperability).
The complete process of advancing a metric specification to a
standard as defined by this document is illustrated in Figure 3.
Geib, et al. Expires January 3, 2011 [Page 16]
Internet-Draft IPPM standard advancement testing July 2010
,---.
/ \
( Start )
\ / Implementations
`-+-' +-------+
| /| 1 `.
+---+----+ / +-------+ `.-----------+ ,-------.
| RFC | / |Check for | ,' was RFC `. YES
| | / |Equivalence.... clause x --------+
| |/ +-------+ |under | `. clear? ,' |
| Metric \.....| 2 ....relevant | `---+---' +----+---+
| Metric |\ +-------+ |identical | No | |Report |
| Metric | \ |network | +--+----+ |results+|
| ... | \ |conditions | |Modify | |Advance |
| | \ +-------+ | | |Spec +----+RFC |
+--------+ \| n |.'+-----------+ +-------+ |request |
+-------+ +--------+
Illustration of the metric standardisation process
Figure 3
Any recommendation for the advancement of a metric specification MUST
be accompanied by an implementation report, as is the case with all
requests for the advancement of IETF specifications. The
implementation report needs to include the tests performed, the
applied test setup, the specific metrics in the RFC and reports of
the tests performed with two or more implementations. The test plan
needs to specify the precision reached for each measured metric and
thus define the meaning of "statistically equivalent" for the
specific metrics being tested.
Ideally, the test plan would co-evolve with the development of the
metric, since that's when people have the most context in their
thinking regarding the different subtleties that can arise.
In particular, the implementation report MUST as a minimum document:
o The metric compared and the RFC specifying it. This includes
statements as required by the section "Tests of an individual
implementation against a metric specification" of this document.
o The measurement configuration and setup.
o A complete specification of the measurement stream (mean rate,
statistical distribution of packets, packet size or mean packet
size and their distribution), DSCP and any other measurement
Geib, et al. Expires January 3, 2011 [Page 17]
Internet-Draft IPPM standard advancement testing July 2010
stream properties which could result in deviating results.
Deviations in results can be caused also if chosen IP addresses
and ports of different implementations can result in different
layer 2 or layer 3 paths due to operation of Equal Cost Multi-Path
routing in an operational network.
o The duration of each measurement to be used for a metric
validation, the number of measurement points collected for each
metric during each measurement interval (i.e. the probe size) and
the level of confidence derived from this probe size for each
measurement interval.
o The result of the statistical tests performed for each metric
validation as required by the section "Tests of two or more
different implementations against a metric specification" of this
document.
o A parameterization of laboratory conditions and applied traffic
and network conditions allowing reproduction of these laboratory
conditions for readers of the implementation report.
o The documentation helping to improve metric specifications defined
by this section.
All of the tests for each set SHOULD be run in a test setup as
specified in the section "Test setup resulting in identical live
network testing conditions."
If a different test set up is chosen, it is RECOMMENDED to avoid
effects falsifying results of validation measurements caused by real
data networks (like parallelism in devices and networks). Data
networks may forward packets differently in the case of:
o Different packet sizes chosen for different metric
implementations. A proposed countermeasure is selecting the same
packet size when validating results of two samples or a sample
against an original distribution.
o Selection of differing IP addresses and ports used by different
metric implementations during metric validation tests. If ECMP is
applied on IP or MPLS level, different paths can result (note that
it may be impossible to detect an MPLS ECMP path from an IP
endpoint). A proposed counter measure is to connect the
measurement equipment to be compared by a NAT device, or
establishing a single tunnel to transport all measurement traffic
The aim is to have the same IP addresses and port for all
measurement packets or to avoid ECMP based local routing diversion
by using a layer 2 tunnel.
Geib, et al. Expires January 3, 2011 [Page 18]
Internet-Draft IPPM standard advancement testing July 2010
o Different IP options.
o Different DSCP.
o If the N measurements are captured using sequential measurements
instead of simultaneous ones, then the following factors come into
play: Time varying paths and load conditions.
3.6. Miscellaneous
In the case that a metric validation requires capturing rare events,
an impairment generator may have to be added to the test set up.
Inclusion of an impairment generator and the parameterisation of the
impairments generated MUST be documented. Rare events could be
packet duplications, packet loss rates above one digit percentages,
loss patterns or packet re-ordering and so on.
As specified above, 5 singletons are the recommended basis to
minimise interference of random events with the statistical test
proposed by this document. In the case of ratio measurements (like
packet loss), the underlying sum of basic events, against the which
the metric's monitored singletons are "rated", determines the
resolution of the test. A packet loss statistic with a resolution of
1% requires one packet loss statistic-datapoint to consist of 500
delay singletons (of which at least 5 were lost). To compare EDFs on
packet loss requires one hundred such statistics per flow. That
means, all in all at least 50 000 delay singletons are required per
single measurement flow. Live network packet loss is assumed to be
present during main traffic hours only. Let this interval be 5
hours. The required minimum rate of a single measurement flow in
that case is 2.8 packets/sec (assuming a loss of 1% during 5 hours).
If this measurement is too demanding under live network conditions,
an impairment generator should be used.
4. Acknowledgements
Gerhard Hasslinger commented a first version of this document,
suggested statistical tests and the evaluation of time series
information. Henk Uijterwaal pushed this work and Mike Hamilton,
Scott Bradner and Emile Stephan commented on versions of this draft
before initial publication. Carol Davids reviewed the 01 version of
this draft.
5. Contributors
Scott Bradner, Vern Paxson and Allison Mankin drafted bradner-
Geib, et al. Expires January 3, 2011 [Page 19]
Internet-Draft IPPM standard advancement testing July 2010
metrictest [bradner-metrictest], and major parts of it are included
in this document.
6. IANA Considerations
This memo includes no request to IANA.
7. Security Considerations
This draft does not raise any specific security issues.
8. References
8.1. Normative References
[RFC2003] Perkins, C., "IP Encapsulation within IP", RFC 2003,
October 1996.
[RFC2026] Bradner, S., "The Internet Standards Process -- Revision
3", BCP 9, RFC 2026, October 1996.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2330] Paxson, V., Almes, G., Mahdavi, J., and M. Mathis,
"Framework for IP Performance Metrics", RFC 2330,
May 1998.
[RFC2661] Townsley, W., Valencia, A., Rubens, A., Pall, G., Zorn,
G., and B. Palter, "Layer Two Tunneling Protocol "L2TP"",
RFC 2661, August 1999.
[RFC2679] Almes, G., Kalidindi, S., and M. Zekauskas, "A One-way
Delay Metric for IPPM", RFC 2679, September 1999.
[RFC2680] Almes, G., Kalidindi, S., and M. Zekauskas, "A One-way
Packet Loss Metric for IPPM", RFC 2680, September 1999.
[RFC2681] Almes, G., Kalidindi, S., and M. Zekauskas, "A Round-trip
Delay Metric for IPPM", RFC 2681, September 1999.
[RFC2784] Farinacci, D., Li, T., Hanks, S., Meyer, D., and P.
Traina, "Generic Routing Encapsulation (GRE)", RFC 2784,
March 2000.
Geib, et al. Expires January 3, 2011 [Page 20]
Internet-Draft IPPM standard advancement testing July 2010
[RFC3931] Lau, J., Townsley, M., and I. Goyret, "Layer Two Tunneling
Protocol - Version 3 (L2TPv3)", RFC 3931, March 2005.
[RFC4448] Martini, L., Rosen, E., El-Aawar, N., and G. Heron,
"Encapsulation Methods for Transport of Ethernet over MPLS
Networks", RFC 4448, April 2006.
[RFC4459] Savola, P., "MTU and Fragmentation Issues with In-the-
Network Tunneling", RFC 4459, April 2006.
[RFC4656] Shalunov, S., Teitelbaum, B., Karp, A., Boote, J., and M.
Zekauskas, "A One-way Active Measurement Protocol
(OWAMP)", RFC 4656, September 2006.
[RFC4719] Aggarwal, R., Townsley, M., and M. Dos Santos, "Transport
of Ethernet Frames over Layer 2 Tunneling Protocol Version
3 (L2TPv3)", RFC 4719, November 2006.
[RFC4928] Swallow, G., Bryant, S., and L. Andersson, "Avoiding Equal
Cost Multipath Treatment in MPLS Networks", BCP 128,
RFC 4928, June 2007.
[RFC5657] Dusseault, L. and R. Sparks, "Guidance on Interoperation
and Implementation Reports for Advancement to Draft
Standard", BCP 9, RFC 5657, September 2009.
8.2. Informative References
[ADK] Scholz, F. and M. Stephens, "K-sample Anderson-Darling
Tests of fit, for continuous and discrete cases",
University of Washington, Technical Report No. 81,
May 1986.
[GU+Duffield]
Gu, Y., Duffield, N., Breslau, L., and S. Sen, "GRE
Encapsulated Multicast Probing: A Scalable Technique for
Measuring One-Way Loss", SIGMETRICS'07 San Diego,
California, USA, June 2007.
[RFC5357] Hedayat, K., Krzanowski, R., Morton, A., Yum, K., and J.
Babiarz, "A Two-Way Active Measurement Protocol (TWAMP)",
RFC 5357, October 2008.
[Rule of thumb]
Hardy, M., "Confidence interval", March 2010.
[bradner-metrictest]
Bradner, S., Mankin, A., and V. Paxson, "Advancement of
Geib, et al. Expires January 3, 2011 [Page 21]
Internet-Draft IPPM standard advancement testing July 2010
metrics specifications on the IETF Standards Track",
draft -bradner-metricstest-03, (work in progress),
July 2007.
[morton-advance-metrics]
Morton, A., "Problems and Possible Solutions for Advancing
Metrics on the Standards Track", draft -morton-ippm-
advance-metrics-00, (work in progress), July 2009.
[morton-advance-metrics-01]
Morton, A., "Lab Test Results for Advancing Metrics on the
Standards Track", draft -morton-ippm-advance-metrics-01,
(work in progress), June 2010.
Appendix A. An example on a One-way Delay metric validation
The text of this appendix is not binding. It is an example how parts
of a One-way Delay metric test could look like.
http://xml.resource.org/public/rfc/bibxml/
A.1. Compliance to Metric specification requirements
One-way Delay, Loss threshold, RFC 2679
This test determines if implementations use the same configured
maximum waiting time delay from one measurement to another under
different delay conditions, and correctly declare packets arriving in
excess of the waiting time threshold as lost. See Section 3.5 of
RFC2679, 3rd bullet point and also Section 3.8.2 of RFC2679.
(1) Configure a path with 1 sec one-way constant delay.
(2) Measure one-way delay with 2 or more implementations, using
identical waiting time thresholds for loss set at 2 seconds.
(3) Configure the path with 3 sec one-way delay.
(4) Repeat measurements.
(5) Observe that the increase measured in step 4 caused all packets
to be declared lost, and that all packets that arrive
successfully in step 2 are assigned a valid one-way delay.
One-way Delay, First-bit to Last bit, RFC 2679
This test determines if implementations register the same relative
increase in delay from one measurement to another under different
Geib, et al. Expires January 3, 2011 [Page 22]
Internet-Draft IPPM standard advancement testing July 2010
delay conditions. This test tends to cancel the sources of error
which may be present in an implementation. See Section 3.7.2 of
RFC2679, and Section 10.2 of RFC2330.
(1) Configure a path with X ms one-way constant delay, and ideally
including a low-speed link.
(2) Measure one-way delay with 2 or more implementations, using
identical options and equal size small packets (e.g., 100 octet
IP payload).
(3) Maintain the same path with X ms one-way delay.
(4) Measure one-way delay with 2 or more implementations, using
identical options and equal size large packets (e.g., 1500 octet
IP payload).
(5) Observe that the increase measured in steps 2 and 4 is
equivalent to the increase in ms expected due to the larger
serialization time for each implementation. Most of the
measurement errors in each system should cancel, if they are
stationary.
One-way Delay, RFC 2679
This test determines if implementations register the same relative
increase in delay from one measurement to another under different
delay conditions. This test tends to cancel the sources of error
which may be present in an implementation. This test is intended to
evaluate measurments in sections 3 and 4 of RFC2679.
(1) Configure a path with X ms one-way constant delay.
(2) Measure one-way delay with 2 or more implementations, using
identical options.
(3) Configure the path with X+Y ms one-way delay.
(4) Repeat measurements.
(5) Observe that the increase measured in steps 2 and 4 is ~Y ms for
each implementation. Most of the measurement errors in each
system should cancel, if they are stationary.
Error Calibration, RFC 2679
This is a simple check to determine if an implementation reports the
error calibration as required in Section 4.8 of RFC2679. Note that
Geib, et al. Expires January 3, 2011 [Page 23]
Internet-Draft IPPM standard advancement testing July 2010
the context (Type-P) must also be reported.
A.2. Examples related to statistical tests for One-way Delay
A one way delay measurement may pass an ADK test with a timestamp
resultion of 1 ms. The same test may fail, if timestamps with a
resolution of 100 microseconds are eavluated. The implementation
then is then conforming to the metric specification up to a timestamp
resolution of 1 ms.
Let's assume another one way delay measurement comparison between
implementation 1, probing with a frequency of 2 probes per second and
implementation 2 probing at a rate of 2 probes every 3 minutes. To
ensure reasonable confidence in results, sample metrics are
calculated from at least 5 singletons per compared time interval.
This means, sample delay values are calculated for each system for
identical 6 minute intervals for the whole test duration. Per 6
minute interval, the sample metric is calculated from 720 singletons
for implementation 1 and from 6 singletons for implementation 2.
Note, that if outliers are not filtered, moving averages are an
option for an evaluation too. The minimum move of an averaging
interval is three minutes in this example.
The data in table 1 may result from measuring One-Way Delay with
implementation 1 (see column Implemnt_1) and implementation 2 (see
column implemnt_2). Each data point in the table represents a
(rounded) average of the sampled delay values per interval. The
resolution of the clock is one micro-second. The difference in the
delay values may result eg. from different probe packet sizes.
Geib, et al. Expires January 3, 2011 [Page 24]
Internet-Draft IPPM standard advancement testing July 2010
+------------+------------+-----------------------------+
| Implemnt_1 | Implemnt_2 | Implemnt_2 - Delta_Averages |
+------------+------------+-----------------------------+
| 5000 | 6549 | 4997 |
| 5008 | 6555 | 5003 |
| 5012 | 6564 | 5012 |
| 5015 | 6565 | 5013 |
| 5019 | 6568 | 5016 |
| 5022 | 6570 | 5018 |
| 5024 | 6573 | 5021 |
| 5026 | 6575 | 5023 |
| 5027 | 6577 | 5025 |
| 5029 | 6580 | 5028 |
| 5030 | 6585 | 5033 |
| 5032 | 6586 | 5034 |
| 5034 | 6587 | 5035 |
| 5036 | 6588 | 5036 |
| 5038 | 6589 | 5037 |
| 5039 | 6591 | 5039 |
| 5041 | 6592 | 5040 |
| 5043 | 6599 | 5047 |
| 5046 | 6606 | 5054 |
| 5054 | 6612 | 5060 |
+------------+------------+-----------------------------+
Table 1
Average values of sample metrics captured during identical time
intervals are compared. This excludes random differences caused by
differing probing intervals or differing temporal distance of
singletons resulting from their Poisson distributed sending times.
In the example, 20 values have been picked (note that at least 100
values are recommended for a single run of a real test). Data must
be ordered by ascending rank. The data of Implemnt_1 and Implemnt_2
as shown in the first two columns of table 1 clearly fails an ADK
test with 95% confidence.
The results of Implemnt_2 are now reduced by difference of the
averages of column 2 (rounded to 6581 us) and column 1 (rounded to
5029 us), which is 1552 us. The result may be found in column 3 of
table 1. Comparing column 1 and column 3 of the table by an ADK test
shows, that the data contained in these columns passes an ADK tests
with 95% confidence.
Appendix B. Anderson-Darling 2 sample C++ code
Geib, et al. Expires January 3, 2011 [Page 25]
Internet-Draft IPPM standard advancement testing July 2010
/* Routines for computing the Anderson-Darling 2 sample
* test statistic.
*
* Implemented based on the description in
* "Anderson-Darling K Sample Test" Heckert, Alan and
* Filliben, James, editors, Dataplot Reference Manual,
* Chapter 15 Auxiliary, NIST, 2004.
* Official Reference by 2010
* Heckert, N. A. (2001). Dataplot website at the
* National Institute of Standards and Technology:
* http://www.itl.nist.gov/div898/software/dataplot.html/
* June 2001.
*/
#include <iostream>
#include <fstream>
#include <vector>
#include <sstream>
using namespace std;
vector<double> vec1, vec2;
double adk_result;
double adk_criterium = 1.993;
/* vec1 and vec2 to be initialised with sample 1 and
* sample 2 values in ascending order.
*/
/* example for iterating the vectors
* for(vector<double>::iterator it = vec1->begin();
* it != vec1->end(); it++
* {
* cout << *it << endl;
* }
*/
static int k, val_st_z_samp1, val_st_z_samp2,
val_eq_z_samp1, val_eq_z_samp2,
j, n_total, n_sample1, n_sample2, L,
max_number_samples, line, maxnumber_z;
static int column_1, column_2;
static double adk, n_value, z, sum_adk_samp1,
sum_adk_samp2, z_aux;
static double H_j, F1j, hj, F2j, denom_1_aux, denom_2_aux;
static bool next_z_sample2, equal_z_both_samples;
static int stop_loop1, stop_loop2, stop_loop3,old_eq_line2,
old_eq_line1;
Geib, et al. Expires January 3, 2011 [Page 26]
Internet-Draft IPPM standard advancement testing July 2010
static double adk_criterium = 1.993;
k = 2;
n_sample1 = vec1->size() - 1;
n_sample2 = vec2->size() - 1;
// -1 because vec[0] is a dummy value
n_total = n_sample1 + n_sample2;
/* value equal to the line with a value = zj in sample 1.
* Here j=1, so the line is 1.
*/
val_eq_z_samp1 = 1;
/* value equal to the line with a value = zj in sample 2.
* Here j=1, so the line is 1.
*/
val_eq_z_samp2 = 1;
/* value equal to the last line with a value < zj
* in sample 1. Here j=1, so the line is 0.
*/
val_st_z_samp1 = 0;
/* value equal to the last line with a value < zj
* in sample 1. Here j=1, so the line is 0.
*/
val_st_z_samp2 = 0;
sum_adk_samp1 = 0;
sum_adk_samp2 = 0;
j = 1;
// as mentioned above, j=1
equal_z_both_samples = false;
next_z_sample2 = false;
//assuming the next z to be of sample 1
stop_loop1 = n_sample1 + 1;
// + 1 because vec[0] is a dummy, see n_sample1 declaration
Geib, et al. Expires January 3, 2011 [Page 27]
Internet-Draft IPPM standard advancement testing July 2010
stop_loop2 = n_sample2 + 1;
stop_loop3 = n_total + 1;
/* The required z values are calculated until all values
* of both samples have been taken into account. See the
* lines above for the stoploop values. Construct required
* to avoid a mathematical operation in the While condition
*/
while (((stop_loop1 > val_eq_z_samp1)
|| (stop_loop2 > val_eq_z_samp2)) && stop_loop3 > j)
{
if(val_eq_z_samp1 < n_sample1+1)
{
/* here, a preliminary zj value is set.
* See below how to calculate the actual zj.
*/
z = (*vec1)[val_eq_z_samp1];
/* this while sequence calculates the number of values
* equal to z.
*/
while ((val_eq_z_samp1+1 < n_sample1)
&& z == (*vec1)[val_eq_z_samp1+1] )
{
val_eq_z_samp1++;
}
}
else
{
val_eq_z_samp1 = 0;
val_st_z_samp1 = n_sample1;
// this should be val_eq_z_samp1 - 1 = n_sample1
}
if(val_eq_z_samp2 < n_sample2+1)
{
z_aux = (*vec2)[val_eq_z_samp2];;
/* this while sequence calculates the number of values
* equal to z_aux
*/
while ((val_eq_z_samp2+1 < n_sample2)
Geib, et al. Expires January 3, 2011 [Page 28]
Internet-Draft IPPM standard advancement testing July 2010
&& z_aux == (*vec2)[val_eq_z_samp2+1] )
{
val_eq_z_samp2++;
}
/* the smaller of the two actual data values is picked
* as the next zj.
*/
if(z > z_aux)
{
z = z_aux;
next_z_sample2 = true;
}
else
{
if (z == z_aux)
{
equal_z_both_samples = true;
}
/* This is the case, if the last value of column1 is
* smaller than the remaining values of column2.
*/
if (val_eq_z_samp1 == 0)
{
z = z_aux;
next_z_sample2 = true;
}
}
}
else
{
val_eq_z_samp2 = 0;
val_st_z_samp2 = n_sample2;
// this should be val_eq_z_samp2 - 1 = n_sample2
}
/* in the following, sum j = 1 to L is calculated for
* sample 1 and sample 2.
*/
if (equal_z_both_samples)
{
/* hj is the number of values in the combined sample
Geib, et al. Expires January 3, 2011 [Page 29]
Internet-Draft IPPM standard advancement testing July 2010
* equal to zj
*/
hj = val_eq_z_samp1 - val_st_z_samp1
+ val_eq_z_samp2 - val_st_z_samp2;
/* H_j is the number of values in the combined sample
* smaller than zj plus one half the the number of
* values in the combined sample equal to zj
* (that's hj/2).
*/
H_j = val_st_z_samp1 + val_st_z_samp2
+ hj / 2;
/* F1j is the number of values in the 1st sample
* which are less than zj plus one half the number
* of values in this sample which are equal to zj.
*/
F1j = val_st_z_samp1 + (double)
(val_eq_z_samp1 - val_st_z_samp1) / 2;
/* F2j is the number of values in the 1st sample
* which are less than zj plus one half the number
* of values in this sample which are equal to zj.
*/
F2j = val_st_z_samp2 + (double)
(val_eq_z_samp2 - val_st_z_samp2) / 2;
/* set the line of values equal to zj to the
* actual line of the last value picked for zj.
*/
val_st_z_samp1 = val_eq_z_samp1;
/* Set the line of values equal to zj to the actual
* line of the last value picked for zjof each
* sample. This is required as data smaller than zj
* is accounted differently than values equal to zj.
*/
val_st_z_samp2 = val_eq_z_samp2;
/* next the lines of the next values z, ie. zj+1
* are addressed.
*/
val_eq_z_samp1++;
Geib, et al. Expires January 3, 2011 [Page 30]
Internet-Draft IPPM standard advancement testing July 2010
/* next the lines of the next values z, ie.
* zj+1 are addressed
*/
val_eq_z_samp2++;
}
else
{
/* the smaller z value was contained in sample 2,
* hence this value is the zj to base the following
* calculations on.
*/
if (next_z_sample2)
{
/* hj is the number of values in the combined
* sample equal to zj, in this case these are
* within sample 2 only.
*/
hj = val_eq_z_samp2 - val_st_z_samp2;
/* H_j is the number of values in the combined sample
* smaller than zj plus one half the the number of
* values in the combined sample equal to zj
* (that's hj/2).
*/
H_j = val_st_z_samp1 + val_st_z_samp2
+ hj / 2;
/* F1j is the number of values in the 1st sample which
* are less than zj plus one half the number of values in
* this sample which are equal to zj.
* As val_eq_z_samp2 < val_eq_z_samp1, these are the
* val_st_z_samp1 only.
*/
F1j = val_st_z_samp1;
/* F2j is the number of values in the 1st sample which
* are less than zj plus one half the number of values in
* this sample which are equal to zj. The latter are from
* sample 2 only in this case.
*/
F2j = val_st_z_samp2 + (double)
(val_eq_z_samp2 - val_st_z_samp2) / 2;
Geib, et al. Expires January 3, 2011 [Page 31]
Internet-Draft IPPM standard advancement testing July 2010
/* Set the line of values equal to zj to the actual line
* of the last value picked for zj of sample 2 only in
* this case.
*/
val_st_z_samp2 = val_eq_z_samp2;
/* next the line of the next value z, ie. zj+1 is
* addressed. Here, only sample 2 must be addressed.
*/
val_eq_z_samp2++;
if (val_eq_z_samp1 == 0)
{
val_eq_z_samp1 = stop_loop1;
}
}
/* the smaller z value was contained in sample 2,
* hence this value is the zj to base the following
* calculations on.
*/
else
{
/* hj is the number of values in the combined
* sample equal to zj, in this case these are
* within sample 1 only.
*/
hj = val_eq_z_samp1 - val_st_z_samp1;
/* H_j is the number of values in the combined
* sample smaller than zj plus one half the the number
* of values in the combined sample equal to zj
* (that's hj/2).
*/
H_j = val_st_z_samp1 + val_st_z_samp2
+ hj / 2;
/* F1j is the number of values in the 1st sample which
* are less than zj plus, in this case these are within
* sample 1 only one half the number of values in this
* sample which are equal to zj. The latter are from
* sample 1 only in this case.
*/
F1j = val_st_z_samp1 + (double)
Geib, et al. Expires January 3, 2011 [Page 32]
Internet-Draft IPPM standard advancement testing July 2010
(val_eq_z_samp1 - val_st_z_samp1) / 2;
/* F2j is the number of values in the 1st sample which
* are less than zj plus one half the number of values
* in this sample which are equal to zj. As
* val_eq_z_samp1 < val_eq_z_samp2, these are the
* val_st_z_samp2 only.
*/
F2j = val_st_z_samp2;
/* Set the line of values equal to zj to the actual line
* of the last value picked for zj of sample 1 only in
* this case
*/
val_st_z_samp1 = val_eq_z_samp1;
/* next the line of the next value z, ie. zj+1 is
* addressed. Here, only sample 1 must be addressed.
*/
val_eq_z_samp1++;
if (val_eq_z_samp2 == 0)
{
val_eq_z_samp2 = stop_loop2;
}
}
}
denom_1_aux = n_total * F1j - n_sample1 * H_j;
denom_2_aux = n_total * F2j - n_sample2 * H_j;
sum_adk_samp1 = sum_adk_samp1 + hj
* (denom_1_aux * denom_1_aux) /
(H_j * (n_total - H_j)
- n_total * hj / 4);
sum_adk_samp2 = sum_adk_samp2 + hj
* (denom_2_aux * denom_2_aux) /
(H_j * (n_total - H_j)
- n_total * hj / 4);
next_z_sample2 = false;
equal_z_both_samples = false;
/* index to count the z. It is only required to prevent
* the while slope to execute endless
*/
Geib, et al. Expires January 3, 2011 [Page 33]
Internet-Draft IPPM standard advancement testing July 2010
j++;
}
// calculating the adk value is the final step.
adk_result = (double) (n_total - 1) / (n_total
* n_total * (k - 1))
* (sum_adk_samp1 / n_sample1
+ sum_adk_samp2 / n_sample2);
/* if(adk_result <= adk_criterium)
* adk_2_sample test is passed
*/
Figure 4
Appendix C. Glossary
+-------------+-----------------------------------------------------+
| ADK | Anderson-Darling K-Sample test, a test used to |
| | check whether two samples have the same statistical |
| | distribution. |
| ECMP | Equal Cost Multipath, a load balancing mechanism |
| | evaluating MPLS labels stacks, IP addresses and |
| | ports. |
| EDF | The "Empirical Distribution Function" of a set of |
| | scalar measurements is a function F(x) which for |
| | any x gives the fractional proportion of the total |
| | measurements that were smaller than or equal as x. |
| Metric | A measured quantity related to the performance and |
| | reliability of the Internet, expressed by a value. |
| | This could be a singleton (single value), a sample |
| | of single values or a statistic based on a sample |
| | of singletons. |
| OWAMP | One-way Active Measurement Protocol, a protocol for |
| | communication between IPPM measurement systems |
| | specified by IPPM. |
| OWD | One-Way Delay, a performance metric specified by |
| | IPPM. |
| Sample | A sample metric is derived from a given singleton |
| metric | metric by evaluating a number of distinct instances |
| | together. |
| Singleton | A singleton metric is, in a sense, one atomic |
| metric | measurement of this metric. |
Geib, et al. Expires January 3, 2011 [Page 34]
Internet-Draft IPPM standard advancement testing July 2010
| Statistical | A 'statistical' metric is derived from a given |
| metric | sample metric by computing some statistic of the |
| | values defined by the singleton metric on the |
| | sample. |
| TWAMP | Two-way Active Measurement Protocol, a protocol for |
| | communication between IPPM measurement systems |
| | specified by IPPM. |
+-------------+-----------------------------------------------------+
Table 2
Authors' Addresses
Ruediger Geib (editor)
Deutsche Telekom
Heinrich Hertz Str. 3-7
Darmstadt, 64295
Germany
Phone: +49 6151 628 2747
Email: Ruediger.Geib@telekom.de
Al Morton
AT&T Labs
200 Laurel Avenue South
Middletown, NJ 07748
USA
Phone: +1 732 420 1571
Fax: +1 732 368 1192
Email: acmorton@att.com
URI: http://home.comcast.net/~acmacm/
Reza Fardid
Cariden Technologies
888 Villa Street, Suite 500
Mountain View, CA 94041
USA
Phone:
Email: rfardid@cariden.com
Geib, et al. Expires January 3, 2011 [Page 35]
Internet-Draft IPPM standard advancement testing July 2010
Alexander Steinmitz
HS Fulda
Marquardstr. 35
Fulda, 36039
Germany
Phone:
Email: steinionline@gmx.de
Geib, et al. Expires January 3, 2011 [Page 36]