Network Working Group G. Bumgardner
Internet-Draft Cisco
Intended status: Standards Track June 12, 2012
Expires: December 14, 2012
Automatic Multicast Tunneling
draft-ietf-mboned-auto-multicast-14
Abstract
This document describes Automatic Multicast Tunneling (AMT), a
protocol for delivering multicast traffic from sources in a
multicast-enabled network to receivers that lack multicast
connectivity to the source network. The protocol uses UDP
encapsulation and unicast replication to provide this functionality.
The AMT protocol is specifically designed to support rapid deployment
by requiring minimal changes to existing network infrastructure.
Status of this Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on December 14, 2012.
Copyright Notice
Copyright (c) 2012 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
Bumgardner Expires December 14, 2012 [Page 1]
Internet-Draft AMT June 2012
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
This document may contain material from IETF Documents or IETF
Contributions published or made publicly available before November
10, 2008. The person(s) controlling the copyright in some of this
material may not have granted the IETF Trust the right to allow
modifications of such material outside the IETF Standards Process.
Without obtaining an adequate license from the person(s) controlling
the copyright in such materials, this document may not be modified
outside the IETF Standards Process, and derivative works of it may
not be created outside the IETF Standards Process, except to format
it for publication as an RFC or to translate it into languages other
than English.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Applicability . . . . . . . . . . . . . . . . . . . . . . . . 4
3. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 5
3.1. Requirements Notation . . . . . . . . . . . . . . . . . . 5
3.2. Definitions . . . . . . . . . . . . . . . . . . . . . . . 5
3.3. Abbreviations . . . . . . . . . . . . . . . . . . . . . . 6
4. Protocol Overview . . . . . . . . . . . . . . . . . . . . . . 8
4.1. General Architecture . . . . . . . . . . . . . . . . . . . 8
4.2. General Operation . . . . . . . . . . . . . . . . . . . . 17
5. Protocol Description . . . . . . . . . . . . . . . . . . . . . 32
5.1. Protocol Messages . . . . . . . . . . . . . . . . . . . . 32
5.2. Gateway Operation . . . . . . . . . . . . . . . . . . . . 47
5.3. Relay Operation . . . . . . . . . . . . . . . . . . . . . 62
6. Security Considerations . . . . . . . . . . . . . . . . . . . 73
7. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 76
7.2. IPv4 Address Prefix Allocation for IGMP Source
Addresses . . . . . . . . . . . . . . . . . . . . . . . . 76
8. Contributors . . . . . . . . . . . . . . . . . . . . . . . . . 77
9. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 78
10. References . . . . . . . . . . . . . . . . . . . . . . . . . . 79
10.1. Normative References . . . . . . . . . . . . . . . . . . . 79
10.2. Informative References . . . . . . . . . . . . . . . . . . 79
Appendix A. Implementation Notes . . . . . . . . . . . . . . . . 82
Author's Address . . . . . . . . . . . . . . . . . . . . . . . . . 85
Bumgardner Expires December 14, 2012 [Page 2]
Internet-Draft AMT June 2012
1. Introduction
The advantages and benefits provided by multicast technologies are
well known. There are a number of application areas that are ideal
candidates for the use of multicast, including media broadcasting,
video conferencing, collaboration, real-time data feeds, data
replication, and software updates. Unfortunately, many of these
applications lack multicast connectivity to networks that carry
traffic generated by multicast sources. The reasons for the lack of
connectivity vary, but are primarily the result of service provider
policies and network limitations.
Automatic Multicast Tunneling (AMT) is a protocol that uses UDP-based
encapsulation to overcome the aforementioned lack of multicast
connectivity. AMT enables sites, hosts or applications that do not
have native multicast access to a network with multicast connectivity
to a source, to request and receive SSM [RFC4607] and ASM [RFC1112]
traffic from a network that does provide multicast connectivity to
that source.
Bumgardner Expires December 14, 2012 [Page 3]
Internet-Draft AMT June 2012
2. Applicability
This document describes a protocol that may be used to deliver
multicast traffic from a multicast enabled network to sites that lack
multicast connectivity to the source network. This document does not
describe any methods for sourcing multicast traffic from isolated
sites as this topic is out of scope.
AMT is not intended to be used as a substitute for native multicast,
especially in conditions or environments requiring high traffic flow.
AMT uses unicast replication to reach multiple receivers and the
bandwidth cost for this replication will be higher than that required
if the receivers were reachable via native multicast.
Bumgardner Expires December 14, 2012 [Page 4]
Internet-Draft AMT June 2012
3. Terminology
3.1. Requirements Notation
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
3.2. Definitions
This document adopts the following definitions for use in describing
the protocol:
Downstream:
A downstream interface or connection that faces away from the
multicast distribution root or towards multicast receivers.
Upstream:
An upstream interface or connection that faces a multicast
distribution root or source.
Non-Broadcast Multi-Access (NMBA):
A non-broadcast multiple-access (NBMA) network or interface is one
to which multiple network nodes (hosts or routers) are attached,
but where packets are transmitted directly from one node to
another node over a virtual circuit or physical link. NBMA
networks do not support multicast or broadcast traffic - a node
that sources multicast traffic must replicate the multicast
packets for separate transmission to each node that has requested
the multicast traffic.
Multicast Receiver:
An entity that requests and receives multicast traffic. A
receiver may be a router, host, application, or application
component. The method by which a receiver transmits group
membership requests and receives multicast traffic varies
according to receiver type.
Group Membership Database:
A group membership database describes the current multicast
subscription/reception sate for an interface or system.
Reception State:
The multicast subscription state of a pseudo, virtual or physical
network interface. See group membership database.
Bumgardner Expires December 14, 2012 [Page 5]
Internet-Draft AMT June 2012
Subscription:
A group or state entry in a group membership database or reception
state table.
Group Membership Protocol:
The term "group membership protocol" is used as a generic
reference to the Internet Group Management (IGMP) ([RFC1112],
[RFC2236], [RFC3376]) or Multicast Listener Discovery ([RFC2710],
[RFC3810]) protocols.
Multicast Protocol:
The term "multicast protocol" is used as a generic reference to
multicast routing protocols used to join or leave multicast
distribution trees such as PIM-SM [RFC4601].
Network Address Translation (NAT):
Network Address Translation is the process of modifying the source
IP address and port numbers carried by an IP packet while
transiting a network node (See [RFC2663]). Intervening NAT
devices may change the source address and port carried by messages
sent from an AMT gateway to an AMT relay, possibly producing
changes in protocol state and behavior.
Anycast:
A network addressing and routing method in which packets from a
single sender are routed to the topologically nearest node in a
group of potential receivers all identified by the same
destination address. See [RFC4786].
3.3. Abbreviations
AMT - Automatic Multicast Tunneling Protocol.
ASM - Any-Source Multicast.
DoS - Denial-of-Service (attack) and DDoS for distributed-DoS.
IGMP - Internet Group Management Protocol (v1, v2 and v3).
IP - Internet Protocol (v4 and v6).
MAC - Message Authentication Code (or Cookie).
MLD - Multicast Listener Discovery protocol (v1 and v2).
NAT - Network Address Translation (or translation node).
Bumgardner Expires December 14, 2012 [Page 6]
Internet-Draft AMT June 2012
NBMA - Non-Broadcast Multi-Access (network, interface or mode)
SSM - Source-Specific Multicast.
PIM - Protocol Independent Multicast.
Bumgardner Expires December 14, 2012 [Page 7]
Internet-Draft AMT June 2012
4. Protocol Overview
This section provides an informative description of the protocol. A
normative description of the protocol and implementation requirements
may be found in section Section 5.
4.1. General Architecture
Isolated Site | Unicast Network | Native Multicast
| (Internet) |
| |
| |
| Group Membership |
+-------+ ===========================> +-------+ Multicast +------+
|Gateway| | | | Relay |<----//----|Source|
+-------+ <=========================== +-------+ +------+
| Multicast Data |
| |
| |
Figure 1: Basic AMT Architecture
The AMT protocol employs a client-server model in which a "gateway"
sends requests to receive specific multicast traffic to a "relay"
which responds by delivering the requested multicast traffic back to
the gateway.
Gateways are generally deployed within networks that lack multicast
support or lack connectivity to a multicast-enabled network
containing multicast sources of interest.
Relays are deployed within multicast-enabled networks that contain,
or have connectivity to, multicast sources.
4.1.1. Relationship to IGMP and MLD Protocols
AMT relies on the Internet Group Management (IGMP) [RFC3376] and
Multicast Listener Discovery (MLD) [RFC3810] protocols to provide the
functionality required to manage, communicate, and act on changes in
multicast group membership. A gateway or relay implementation does
not necessarily require a fully-functional, conforming implementation
of IGMP or MLD to adhere to this specification, but the protocol
description that appears in this document assumes that this is the
case. The minimum functional and behavioral requirements for the
IGMP and MLD protocols are described in Section 5.2.1 and
Section 5.3.1.
Bumgardner Expires December 14, 2012 [Page 8]
Internet-Draft AMT June 2012
Gateway Relay
General _____ _____
___________ Query | | | | Query ___________
| |<------| | | |<------| |
| Host Mode | | AMT | | AMT | |Router Mode|
| IGMP/MLD | | | UDP | | | IGMP/MLD |
|___________|------>| |<----->| |------>|___________|
Report | | | | Report
Leave/Done | | | | Leave/Done
| | | |
IP Multicast <------| | | |<------ IP Multicast
|_____| |_____|
Multicast Reception State Managed By IGMP/MLD
A gateway runs the host portion of the IGMP and MLD protocols to
generate group membership updates that are sent via AMT messages to a
relay. A relay runs the router portion of the IGMP and MLD protocols
to process the group membership updates to produce the required
changes in multicast forwarding state. A relay uses AMT messages to
send incoming multicast IP datagrams to gateways according to their
current group membership state.
The primary function of AMT is to provide the handshaking,
encapsulation and decapsulation required to transport the IGMP and
MLD messages and multicast IP datagrams between the gateways and
relays. The IGMP and MLD messages that are exchanged between
gateways and relays are encapsulated as complete IP datagrams within
AMT control messages. Multicast IP datagrams are replicated and
encapsulated in AMT data messages. All AMT messages are sent via
unicast UDP/IP.
4.1.2. Gateways
The downstream side of a gateway services one or more receivers - the
gateway accepts group membership requests from receivers and forwards
requested multicast traffic back to those receivers.
The upstream side of a gateway connects to relays. A gateway sends
encapsulated IGMP and MLD messages to a relay to indicate an interest
in receiving specific multicast traffic.
Bumgardner Expires December 14, 2012 [Page 9]
Internet-Draft AMT June 2012
4.1.2.1. Architecture
Each gateway possesses a logical pseudo-interface:
join/leave ---+ +----------+
| | |
V IGMPv3/MLDv2 | |
+---------+ General Query| | AMT
|IGMP/MLD |<-------------| AMT | Messages +------+
|Host Mode| | Gateway |<-------->|UPD/IP|
|Protocol |------------->|Pseudo I/F| +------+
+---------+ IGMP/MLD | | ^
Report | | |
Leave/Done | | V
IP Multicast <---------------------| | +---+
+----------+ |I/F|
+---+
Figure 2: AMT Gateway Pseudo-Interface
The pseudo-interface is conceptually a network interface on which the
gateway executes the host portion of the IPv4/IGMP (v2 or v3) and
IPv6/MLD (v1 or v2) protocols. The multicast reception state of the
pseudo-interface is manipulated using the IGMP or MLD service
interface. The IGMP and MLD host protocols produce IP datagrams
containing group membership messages that the gateway will send to
the relay. The IGMP and MLD protocols also supply the retransmission
and timing behavior required for protocol robustness.
All AMT encapsulation, decapsulation and relay interaction is assumed
to occur within the pseudo-interface.
A gateway host or application may create separate interfaces for
IPv4/IGMP and IPv6/MLD. A gateway host or application may also
require additional pseudo-interfaces for each source or domain-
specific relay address.
Within this document, the term "gateway" may be used as a generic
reference to an entity executing the gateway protocol, a gateway
pseudo-interface, or a gateway device that has one or more interfaces
connected to a unicast inter-network and one or more AMT gateway
pseudo-interfaces.
Bumgardner Expires December 14, 2012 [Page 10]
Internet-Draft AMT June 2012
The following diagram illustrates how an existing host IP stack
implementation might be used to provide AMT gateway functionality to
a multicast application:
+-----------------------------------------------------+
|Host |
| ______________________________________ |
| | | |
| | ___________________________ | |
| | | | | |
| | | v | |
| | | +-----------+ +--------------+ |
| | | |Application| | AMT Daemon | |
| | | +-----------+ +--------------+ |
| | | join/leave | ^ data ^ AMT |
| | | | | | |
| | | +----|---|-------------|-+ |
| | | | __| |_________ | | |
| | | | | | | | |
| | | | | Sockets | | | |
| | | +-|------+-------+-|---|-+ |
| | | | | IGMP | TCP | |UDP| | |
| | | +-|------+-------+-|---|-+ |
| | | | | ^ IP | | | |
| | | | | | ____________| | | |
| | | | | | | | | |
| | | +-|-|-|----------------|-+ |
| | | | | | | |
| | | IP(IGMP)| | |IP(UDP(data)) |IP(UDP(AMT)) |
| | | v | | v |
| | | +-----------+ +---+ |
| | | |Virtual I/F| |I/F| |
| | | +-----------+ +---+ |
| | | | ^ ^ |
| | | IP(IGMP)| |IP(UDP(data)) | |
| | |_________| |IP(IGMP) | |
| | | | |
| |_________________| | |
| | |
+--------------------------------------|--------------+
v
AMT Relay
Virtual Interface Implementation Example
In this example, the host IP stack uses a virtual network interface
to interact with a gateway pseudo-interface implementation.
Bumgardner Expires December 14, 2012 [Page 11]
Internet-Draft AMT June 2012
4.1.2.2. Use-Cases
Use-cases for gateway functionality include:
IGMP/MLD Proxy
An IGMP/MLD proxy that runs AMT on an upstream interface and
router-mode IGMP/MLD on downstream interfaces to provide host
access to multicast traffic via the IGMP and MLD protocols.
Virtual Network Interface
A virtual network interface or pseudo network device driver that
runs AMT on a physical network interface to provide socket layer
access to multicast traffic via the IGMP/MLD service interface
provided by the host IP stack.
Application
An application or application component that implements and
executes IGMP/MLD and AMT internally to gain access to multicast
traffic.
4.1.3. Relays
The downstream side of a relay services gateways - the relay accepts
encapsulated IGMP and MLD group membership messages from gateways and
encapsulates and forwards the requested multicast traffic back to
those gateways.
The upstream side of a relay communicates with a native multicast
infrastructure - the relay sends join and prune/leave requests
towards multicast sources and accepts requested multicast traffic
from those sources.
Bumgardner Expires December 14, 2012 [Page 12]
Internet-Draft AMT June 2012
4.1.3.1. Architecture
Each relay possesses a logical pseudo-interface:
+------------------------------+
+--------+ | Multicast Control Plane |
| |IGMP/MLD| |
| | Query* | +------------+ +----------+ |
| |<---//----|IGMPv3/MLDv2| | | |
AMT | | | |Router Mode |->| PIM-SM |<-->
+------+ Messages | AMT |----//--->|Protocol | | | |
|UDP/IP|<-------->| Relay |IGMP/MLD| +------------+ +----------+ |
+------+ | Pseudo | Report | | | |
^ | I/F | Leave/ +------|---------------|-------+
| | | Done | |
| | | v |
V | | IP +-----------+ |
+---+ | | Multicast |Multicast |<------+
|I/F| | |<---//-----|Forwarding |
+---+ +--------+ |Plane |<--- IP Multicast
+-----------+
* Queries, if generated, are consumed by the pseudo-interface.
AMT Relay Pseudo-Interface (Router-Based)
The pseudo-interface is conceptually a network interface on which the
relay runs the router portion of the IPv4/IGMPv3 and IPv6/MLDv2
protocols. Relays do not send unsolicited IGMPv3/MLDv2 query
messages to gateways so relays must consume or discard any local
queries normally generated by IGMPv3 or MLDv2.
A relay maintains group membership state for each gateway connected
through the pseudo-interface as well as for the entire pseudo-
interface (if multiple gateways are managed via a single interface).
Multicast packets received on upstream interfaces on the relay are
routed to the pseudo-interface where they are replicated,
encapsulated and sent to interested gateways. Changes in the pseudo-
interface group membership state may trigger the transmission of
multicast protocol requests upstream towards a given source or
rendezvous point and cause changes in internal routing/forwarding
state.
The relay pseudo-interface is a architectural abstraction used to
describe AMT protocol operation. For the purposes of this document,
the pseudo-interface is most easily viewed as an interface to a
single gateway - encapsulation, decapsulation, and other AMT-specific
processing occurs "within" the pseudo-interface while forwarding and
Bumgardner Expires December 14, 2012 [Page 13]
Internet-Draft AMT June 2012
replication occur outside of it.
An alternative view is to treat the pseudo-interface as a non-
broadcast multi-access (NBMA) network interface whose link layer is
the unicast-only network over which AMT messages are exchanged with
gateways. Individual gateways are conceptually treated as logical
NBMA links on the interface. In this architectural model, group
membership tracking, replication and forwarding functions occur in
the pseudo-interface.
This document does not specify any particular architectural solution
- a relay developer may choose to implement and distribute protocol
functionality as required to take advantage of existing relay
platform services and architecture.
Within this document, the term "relay" may be used as a generic
reference to an entity executing the relay protocol, a relay pseudo-
interface, or a relay device that has one or more network interfaces
with multicast connectivity to a native multicast infrastructure,
zero or more interfaces connected to a unicast inter-network, and one
or more relay pseudo-interfaces.
4.1.3.2. Use-Cases
Use-cases for relay functionality include:
Multicast Router
A multicast router that runs AMT on a downstream interface to
provide gateway access to multicast traffic. A "relay router"
uses a multicast routing protocol (e.g. PIM-SM RFC4601 [RFC4601])
to construct a forwarding path for multicast traffic by sending
join and prune messages to neighboring routers to join or leave
multicast distribution trees for a given SSM source or ASM
rendezvous point.
IGMP/MLD Proxy Router
An IGMP/MLD proxy that runs AMT on a downstream interface and
host-mode IGMPv3/MLDv2 on a upstream interface. This "relay
proxy" sends group membership reports to a local, multicast-
enabled router to join and leave specific SSM or ASM groups.
4.1.4. Deployment
The AMT protocol calls for a relay deployment model that uses anycast
addressing [RFC1546][RFC4291] to pair gateways with relays.
Under this approach, one or more relays advertise a route for the
same IP address prefix. To find a relay with which to communicate, a
Bumgardner Expires December 14, 2012 [Page 14]
Internet-Draft AMT June 2012
gateway sends a message to an anycast IP address within that prefix.
This message is routed to the topologically-nearest relay that has
advertised the prefix. The relay that receives the message responds
by sending its unicast address back to the gateway. The gateway uses
this address as the destination address for any messages it
subsequently sends to the relay.
The use of anycast addressing provides the following benefits:
o Relays may be deployed at multiple locations within a single
multicast-enabled network. Relays might be installed "near"
gateways to reduce bandwidth requirements, latency and limit the
number of gateways that might be serviced by a single relay.
o Relays may be added or removed at any time thereby allowing staged
deployment, scaling and hot-swapping - the relay discovery process
will always return the nearest operational relay.
o Relays may take themselves offline when they exhaust resources
required to service additional gateways. Existing gateway
connections may be preserved, but new gateway requests would be
routed to the next-nearest relay.
4.1.4.1. Public Versus Private
Ideally, the AMT protocol would provide a universal solution for
connecting receivers to multicast sources - that any gateway could be
used to access any globally advertised multicast source via publicly-
accessible, widely-deployed relays. Unfortunately, today's Internet
does not yet allow this, because many relays will lack native
multicast access to sources even though they may be globally
accessible via unicast.
In these cases, a provider may deploy relays within their own source
network to allow for multicast distribution within that network.
Gateways that use these relays must use a provider-specific relay
discovery mechanism or a private anycast address to obtain access to
these relays.
4.1.5. Discovery
To execute the gateway portion of the protocol, a gateway requires a
unicast IP address of an operational relay. This address may be
obtained using a number of methods - it may be statically assigned or
dynamically chosen via some form of relay discovery process.
As described in the previous section, the AMT protocol provides a
relay discovery method that relies on anycast addressing. Gateways
Bumgardner Expires December 14, 2012 [Page 15]
Internet-Draft AMT June 2012
are not required to use AMT relay discovery, but all relay
implementations must support it.
The AMT protocol uses the following terminology when describing the
discovery process:
Relay Discovery Address Prefix:
The anycast address prefix used to route discovery messages to a
relay.
Relay Discovery Address:
The anycast destination address used when sending discovery
messages.
Relay Address:
The unicast IP address obtained as a result of the discovery
process.
4.1.5.1. Relay Discovery Address Selection
The selection of an anycast Relay Discovery Address may be source-
dependent, as a relay located via relay discovery must have multicast
connectivity to a desired source.
Similarly, the selection of a unicast Relay address may be source-
dependent, as a relay contacted by a gateway to supply multicast
traffic must have native multicast connectivity to the traffic source
Methods that might be used to perform source-specific or group-
specific relay selection are highly implementation-dependent and are
not further addressed by this document. Possible approaches include
the use of static lookup tables, DNS-based queries, or a provision of
a service interface that accepts join requests on (S,G,relay-
discovery-address) or (S,G,relay-address) tuples.
4.1.5.2. IANA-Assigned Relay Discovery Address Prefix
This document calls for IANA to allocate an anycast address prefix
for use in advertising and discovering publicly accessible relays.
A relay discovery address is constructed from the anycast address
prefix by setting the low-order octet of the prefix address to 1 (for
both IPv4 and IPv6).
Public relays must advertise a route to the anycast address prefix
and configure an interface to respond to the relay discovery address.
The IANA address assignments are discussed in Section 7.
Bumgardner Expires December 14, 2012 [Page 16]
Internet-Draft AMT June 2012
4.2. General Operation
4.2.1. Message Sequences
The AMT protocol defines the following messages for control and
encapsulation. These messages are exchanged as UDP/IP datagrams, one
message per datagram.
Relay Discovery:
Sent by gateways to solicit a Relay Advertisement from any relay.
Used to find a relay with which to communicate.
Relay Advertisement:
Sent by relays as a response to a Relay Discovery message. Used
to deliver a relay address to a gateway.
Request:
Sent by gateways to solicit a Membership Query message from a
relay.
Membership Query:
Sent by relays as a response to a Request message. Used to
deliver an encapsulated IGMPv3 or MLDv2 query message to the
gateway.
Membership Update:
Sent by gateways to deliver an encapsulated IGMP or MLD report/
leave/done message to a relay.
Multicast Data:
Sent by relays to deliver an encapsulated IP multicast datagram or
datagram fragment to a gateway.
Teardown:
Sent by gateways to stop the delivery of Multicast Data messages
requested in an earlier Membership Update message.
The following sections describe how these messages are exchanged to
execute the protocol.
Bumgardner Expires December 14, 2012 [Page 17]
Internet-Draft AMT June 2012
4.2.1.1. Relay Discovery Sequence
Gateway Relay
------- -----
: :
| |
[1] |Relay Discovery |
|------------------->|
| |
| Relay Advertisement| [2]
|<-------------------|
[3] | |
: :
AMT Relay Discovery Sequence
The following sequence describes how the Relay Discovery and Relay
Advertisement messages are used to find a relay with which to
communicate:
1. The gateway sends a Relay Discovery message containing a random
nonce to the Relay Discovery Address. If the Relay Discovery
Address is an anycast address, the message is routed to
topologically-nearest network node that advertises that address.
2. The node receiving the Relay Discovery message sends a Relay
Advertisement message back to the source of the Relay Discovery
message. The message carries a copy of the nonce contained in
the Relay Discovery message and the unicast IP address of a
relay.
3. When the gateway receives the Relay Advertisement message it
verifies that the nonce matches the one sent in the Relay
Discovery message, and if it does, uses the relay address carried
by the Relay Advertisement as the destination address for
subsequent AMT messages.
Note that the responder need not be a relay - the responder may
obtain a relay address by some other means and return the result in
the Relay Advertisement (i.e., the responder is a load-balancer or
broker).
4.2.1.2. Membership Update Sequence
There exists a significant difference between normal IGMP and MLD
behavior and that required by AMT. An IGMP/MLD router acting as a
querier normally transmits query messages on a network interface to
construct and refresh group membership state for the connected
Bumgardner Expires December 14, 2012 [Page 18]
Internet-Draft AMT June 2012
network. These query messages are multicast to all IGMP/MLD enabled
hosts on the network. Each host responds by multicasting report
messages that describe their current multicast reception state.
However, AMT does not allow relays to send unsolicited query messages
to gateways, as the set of active gateways may be unknown to the
relay and potentially quite large. Instead, AMT requires each
gateway to periodically send a message to a relay to solicit a
general-query response. A gateway accomplishes this by sending a
Request message to a relay. The relay responds by sending Membership
Query message back to the gateway. The Membership Query message
carries an encapsulated general query that is processed by the IGMP
or MLD protocol implementation on the gateway to produce a
membership/listener report. Each time the gateway receives a
Membership Query message it starts a timer whose expiration will
trigger the start of a new Request->Membership Query message
exchange. This timer-driven sequence is used to mimic the
transmission of a periodic general query by an IGMP/MLD router. This
query cycle may continue indefinitely once started by sending the
initial Request message.
A membership update occurs when an IGMP or MLD report, leave or done
message is passed to the gateway pseudo-interface. These messages
may be produced as a result of the aforementioned general-query
processing or as a result of receiver interaction with the IGMP/MLD
service interface. Each report is encapsulated and sent to the relay
after the gateway has successfully established communication with the
relay via a Request and Membership Query message exchange. If a
report is passed to the pseudo-interface before the gateway has
received a Membership Query message from the relay, the gateway may
discard the report or queue the report for delivery after a
Membership Query is received. Subsequent IGMP/MLD report/leave/done
messages that are passed to the pseudo-interface are immediately
encapsulated and transmitted to the relay.
Bumgardner Expires December 14, 2012 [Page 19]
Internet-Draft AMT June 2012
IGMP/MLD Pseudo-I/F Relay
-------- ---------- -----
: : :
| | Request |
| 1|-------------------->|
| | Membership Query |2
Query | | Q(0,{}) |
Timer | Start 3|<--------------------|
(QT)<--------------------------| |
| Q(0,{}) | |
|<--------------------| |
4| R({}) | Membership Update |
|-------------------->|5 R({}) |
| |====================>|6a
Join(S,G) : : :
()--------->|7 R({G:ALLOW({S})}) | Membership Update |
|-------------------->|8 R({G:ALLOW({S})}) |
| |====================>|9a Join(S,G)
| | |---------->()
: : :
| ------------|---------------------|------------
| | | | |
| | | Multicast Data | IP(S,G) |
| | | IP(S,G) 10|<--------() |
| | IP(S,G) 11|<====================| |
| | ()<--------| | |
| | | | |
: ------------:---------------------:------------
| Expired | |
(QT)-------------------------->|12 Request |
| 1|-------------------->|
| | Membership Query |2
| | Q(0,{}) |
| Start 3|<--------------------|
(QT)<--------------------------| |
| Q(0,{}) | |
|<--------------------| |
4| R({G:INCLUDE({S})}) | Membership Update |
|-------------------->|5 R({G:INCLUDE({S})})|
| |====================>|6b
Leave(S,G) : : :
()--------->|7 R({G:BLOCK({S})}) | Membership Update |
|-------------------->|8 R({G:BLOCK({S})}) |
| |====================>|9b Prune(S,G)
| | |---------->()
: : :
Membership Update Sequence (IGMPv3/MLDv2 Example)
Bumgardner Expires December 14, 2012 [Page 20]
Internet-Draft AMT June 2012
The following sequence describes how the Request, Membership Query,
and Membership Update messages are used to report current group
membership state or changes in group membership state:
1. A gateway sends a Request message to the relay that contains a
random nonce and a flag indicating whether the relay should
return an IGMPv3 or MLDv2 general query.
2. When the relay receives a Request message, it generates a
message authentication code (MAC) by computing a hash value from
a private secret and the nonce, source IP address, and source
UDP port carried by the Request message. The relay then sends a
Membership Query message to the gateway that contains the
request nonce, the MAC, and an IGMPv3 or MLDv2 general query.
3. When the gateway receives a Membership Query message, it
verifies that the request nonce matches the one sent in the last
Request, and if it does, the gateway saves the request nonce and
MAC for use in sending subsequent Membership Update messages.
The gateway starts a timer whose expiration will trigger the
transmission of a new Request message and extracts the
encapsulated general query message for processing by the IGMP or
MLD protocol. The query timer duration is specified by the
relay in the QQIC field in the IGMPv3 or MLDv2 general query.
4. The gateway's IGMP or MLD protocol implementation processes the
general query to produce a current-state report.
5. When an IGMP or MLD report is passed to the pseudo-interface,
the gateway encapsulates the report in a Membership Update
message and sends it to the relay. The request nonce and MAC
fields in the Membership Update are assigned the values from the
last Membership Query message received for the corresponding
group membership protocol (IGMPv3 or MLDv2).
6. When the relay receives a Membership Update message, it computes
a MAC from a private secret and the request nonce, source IP
address, and source UDP port carried by the message. The relay
accepts the Membership Update message if the received MAC
matches the computed MAC, otherwise the message is ignored. If
the message is accepted, the relay may proceed to allocate,
refresh, or modify tunnel state. This includes making any group
membership, routing and forwarding state changes and issuing any
upstream protocol requests required to satisfy the state change.
The diagram illustrates two scenarios:
A. The gateway has not previously reported any group
subscriptions and the report does not contain any group
Bumgardner Expires December 14, 2012 [Page 21]
Internet-Draft AMT June 2012
subscriptions, so the relay takes no action.
B. The gateway has previously reported a group subscription so
the current-state report lists all current subscriptions.
The relay responds by refreshing tunnel or group state and
resetting any related timers.
7. A receiver indicates to the gateway that it wishes to join
(allow) or leave (block) specific multicast traffic. This
request is typically made using some form IGMP/MLD service
interface (as described in Section 2 of [RFC3376] or Section 3
of [RFC3810]). The IGMP/MLD protocol responds by generating an
IGMP or MLD state-change message.
8. When an IGMP or MLD report/leave/done message is passed to the
pseudo-interface, the gateway encapsulates the message in a
Membership Update message and sends it to the relay. The
request nonce and MAC fields in the Membership Update are
assigned the values from the last Membership Query message
received for the corresponding group membership protocol (IGMP
or MLD).
The IGMP and MLD protocols may generate multiple messages to
provide robustness against packet loss - each of these must be
encapsulated in a new Membership Update message and sent to the
relay. The Querier Robustness Variable (QRV) field in the last
IGMP/MLD query delivered to the IGMP/MLD protocol is typically
used to specify the number of repetitions (i.e., the host adopts
the QRV value as its own Robustness Variable value).
9. When the relay receives a Membership Update message, it again
computes a MAC from a private secret and the request nonce,
source IP address, and source UDP port carried by the message.
The relay accepts the Membership Update message if the received
MAC matches the computed MAC, otherwise the message is ignored.
If the message is accepted, the relay processes the encapsulated
IGMP/MLD and allocates, modifies or deletes tunnel state
accordingly. This includes making any group membership, routing
and forwarding state changes and issuing any upstream protocol
requests required to satisfy the state change. The diagram
illustrates two scenarios:
A. The gateway wishes to add a group subscription.
B. The gateway wishes to delete a previously reported group
subscription.
Bumgardner Expires December 14, 2012 [Page 22]
Internet-Draft AMT June 2012
10. Multicast datagrams transmitted from a source travel through the
native multicast infrastructure to the relay. When the relay
receives a multicast IP datagram that carries a source and
destination address for which a gateway has expressed an
interest in receiving (via the Membership Update message), it
encapsulates the datagram into a Multicast Data message and
sends it to the gateway using the source IP address and UDP port
carried by the Membership Update message as the destination
address.
11. When the gateway receives a Multicast Data message, it extracts
the multicast packet from the message and passes it on to the
appropriate receivers.
12. When the query timer expires the gateway sends a new Request
message to the relay to start a new membership update cycle.
The MAC-based source-authentication mechanism described above
provides a simple defense against malicious attempts to exhaust relay
resources via source-address spoofing. Flooding a relay with spoofed
Request or Membership Update messages may consume computational
resources and network bandwidth, but will not result in the
allocation of state because the Request message is stateless and
spoofed Membership Update messages will fail source-authentication
and be rejected by the relay.
A relay will only allocate new tunnel state if the IGMP/MLD report
carried by the Membership Update message creates one or more group
subscriptions.
A relay deallocates tunnel state after one of the following events;
the gateway sends a Membership Update message containing a report
that results in the deletion of all remaining group subscriptions,
the IGMP/MLD state expires (due to lack of refresh by the gateway),
or the relay receives a valid Teardown message from the gateway.
A gateway that accepts or reports group subscriptions for both IPv4
and IPv6 addresses will send separate Request and Membership Update
messages for each protocol (IPv4/IGMP and IPv6/MLD).
4.2.1.3. Teardown Sequence
A gateway sends a Teardown message to a relay to request that it stop
delivering Multicast Data messages to a tunnel endpoint created by an
earlier Membership Update message. This message is intended to be
used following a gateway address change (See Section 4.2.2.1) to stop
the transmission of undeliverable or duplicate multicast data
messages. Support for the Teardown message is optional - gateways
Bumgardner Expires December 14, 2012 [Page 23]
Internet-Draft AMT June 2012
are not required to send them and relays are not required to act upon
them.
Bumgardner Expires December 14, 2012 [Page 24]
Internet-Draft AMT June 2012
Gateway Relay
------- -----
: Request :
[1] | N |
|---------------------->|
| Membership Query | [2]
| N,MAC,gADDR,gPORT |
|<======================|
[3] | Membership Update |
| ({G:INCLUDE({S})}) |
|======================>|
| |
----------------------:-----------------------:----------------------
| | | |
| | *Multicast Data | *IP Packet(S,G) |
| | gADDR,gPORT |<------------------() |
| *IP Packet(S,G) |<======================| |
| ()<------------------| | |
| | | |
----------------------:-----------------------:----------------------
~ |
~ Request |
[4] | N' |
|---------------------->|
| Membership Query | [5]
| N',MAC',gADDR',gPORT' |
|<======================|
[6] | |
| Teardown |
| N,MAC,gADDR,gPORT |
|---------------------->|
| | [7]
| Membership Update |
| ({G:INCLUDE({S})}) |
|======================>|
| |
----------------------:-----------------------:----------------------
| | | |
| | *Multicast Data | *IP Packet(S,G) |
| | gADDR',gPORT' |<------------------() |
| *IP Packet (S,G) |<======================| |
| ()<------------------| | |
| | | |
----------------------:-----------------------:----------------------
| |
: :
Figure 3: Teardown Message Sequence (IGMPv3/MLDv2 Example)
Bumgardner Expires December 14, 2012 [Page 25]
Internet-Draft AMT June 2012
The following sequence describes how the Membership Query and
Teardown message are used to detect an address change and stop the
delivery of Multicast Data messages to an address:
1. A gateway sends a Request message containing a random nonce to
the relay.
2. The relay sends a Membership Query message to the gateway that
contains the source IP address (gADDR) and source UDP port
(gPORT) values from the Request message. These values will be
used to identify the tunnel should one be created by a subsequent
Membership Update message.
3. When the gateway receives a Membership Query message that carries
the gateway address fields, it compares the gateway IP address
and port number values with those received in the previous
Membership Query (if any). If these values do not match, this
indicates that the Request message arrived at the relay carrying
a different source address than the one sent previously. At this
point in the sequence, no change in source address or port has
occurred.
4. The gateway sends a new Request message to the relay. However,
this Request message arrives at the relay carrying a different
source address than that of the previous Request due to some
change in network interface, address assignment, network topology
or NAT mapping.
5. The relay again responds by sending a Membership Query message to
the gateway that contains the new source IP address (gADDR') and
source UDP port (gPORT') values from the Request message.
6. When the gateway receives the Membership Query message, it
compares the gateway address and port number values against those
returned in the previous Membership Query message.
7. If the reported address or port has changed, the gateway sends a
Teardown message to the relay that contains the request nonce,
MAC, gateway IP address and gateway port number returned in the
earlier Membership Query message. The gateway may send the
Teardown message multiple times where the number of repetitions
is governed by the Querier Robustness Variable (QRV) value
contained in the IGMPv3/MLDv2 general query carried by the
original Membership Query. The gateway continues to process the
new Membership Query message as usual.
8. When the relay receives a Teardown message, it computes a MAC
from a private secret and the request nonce, gateway IP address,
Bumgardner Expires December 14, 2012 [Page 26]
Internet-Draft AMT June 2012
and gateway port number carried by the Teardown message. The
relay accepts the Teardown message if the received MAC matches
the computed MAC, otherwise the message is ignored. If the
message is accepted, the relay makes any group membership,
routing and forwarding state changes required to stop the
transmission of Multicast Data messages to that address.
4.2.1.4. Timeout and Retransmission
The AMT protocol does not establish any requirements regarding what
actions a gateway should take if it fails to receive a response from
a relay. A gateway implementation may wait for an indefinite period
of time to receive a response, may set a time limit on how long to
wait for a response, may retransmit messages should the time limit be
reached, may limit the number of retransmissions, or may simply
report an error.
For example, a gateway may retransmit a Request message if it fails
to receive a Membership Query or expected Multicast Data messages
within some time period. If the gateway fails to receive any
response to a Request after several retransmissions or within some
maximum period of time, it may reenter the relay discovery phase in
an attempt to find a new relay. This topic is addressed in more
detail in Section 5.2.
4.2.2. Tunneling
From the standpoint of a relay, an AMT "tunnel" is identified by the
IP address and UDP port pair used as the destination address for
sending encapsulated multicast IP datagrams to a gateway. This
address is referred here as the tunnel endpoint address.
A gateway sends a Membership Update message to a relay to add or
remove group subscriptions to a tunnel endpoint. The tunnel endpoint
is identified by the source IP address and source UDP port carried by
the Membership Update message when it arrives at a relay (this
address may differ from that carried by the message when it exited
the gateway as a result of network address translation).
The Membership Update messages sent by a single gateway host may
originate from several source addresses or ports - each unique
combination represents a unique tunnel endpoint. A single gateway
host may legitimately create and accept traffic on multiple tunnel
endpoints, e.g., the gateway may use separate ports for the IPv4/IGMP
and IPv6/MLD protocols.
A tunnel is "created" when a gateway sends a Membership Update
message containing an IGMP or MLD membership report that creates one
Bumgardner Expires December 14, 2012 [Page 27]
Internet-Draft AMT June 2012
or more group subscriptions when none currently existed for that
tunnel endpoint address.
A tunnel ceases to exist when all group subscriptions for a tunnel
endpoint are deleted. This may occur as a result of the following
events:
o The gateway sends an IGMP or MLD report, leave or done message to
the relay that deletes the last group subscription linked to the
tunnel endpoint.
o The gateway sends a Teardown message to the relay that causes it
to delete any and all subscriptions bound to the tunnel endpoint.
o The relay stops receiving updates from the gateway until such time
that per-group or per-tunnel timers expire, causing the relay to
delete the subscriptions.
The tunneling approach described above conceptually transforms a
unicast-only inter-network into an NBMA link layer, over which
multicast traffic may be delivered. Each relay, plus the set of all
gateways using the relay, together may be thought of as being on a
separate logical NBMA link, where the "link layer" address is a
UDP/IP address-port pair provided by the Membership Update message.
4.2.2.1. Address Roaming
As described above, each time a relay receives a Membership Update
message from a new source address-port pair, the group subscriptions
described by that message apply to the tunnel endpoint identified by
that address.
This can cause problems for a gateway if the address carried by the
messages it sends to a relay changes unexpectedly. These changes may
cause the relay to transmit duplicate, undeliverable or unrequested
traffic back towards the gateway or an intermediate device. This may
create congestion and have negative consequences for the gateway, its
network, or multicast receivers, and in some cases, may also produce
a significant amount of ICMP traffic directed back towards the relay
by a NAT, router or gateway host.
There are several scenarios in which the address carried by messages
sent by a gateway may change without that gateway's knowledge, as for
example, when:
o The message originates from a different interface on a gateway
that possesses multiple interfaces.
Bumgardner Expires December 14, 2012 [Page 28]
Internet-Draft AMT June 2012
o The DHCP assignment for a gateway interface changes.
o The gateway roams to a different wireless network.
o The address mapping applied by an intervening network-translation-
device (NAT) changes as a result of mapping expiration or routing
changes in a multi-homed network.
In the case where the address change occurs between the transmission
of a Request message and subsequent Membership Update messages, the
relay will simply ignore any Membership Update messages from the new
address because MAC authentication will fail (see Section 4.2.1.2).
The relay may continue to transmit previously requested traffic, but
no duplication will occur, i.e., the possibility for the delivery of
duplicate traffic does not arise until a Request message is received
from the new address.
The protocol provides a method for a gateway to detect an address
change and explicitly request that the relay stop sending traffic to
a previous address. This process involves the Membership Query and
Teardown messages and is described in Section 4.2.1.3.
4.2.2.2. Network Address Translation
The messages sent by a gateway to a relay may be subject to network
address translation (NAT) - the source IP address and UDP port
carried by an IP packet sent by the gateway may be modified multiple
times before arriving at the relay. In the most restrictive form of
NAT, the NAT device will create a new mapping for each combination of
source and destination IP address and UDP port. In this case, bi-
directional communication can only be conducted by sending outgoing
packets to the source address and port carried by the last incoming
packet.
Membership Update Membership Update
src: iADDR:iPORT src: eADDR:ePORT
dst: rADDR:rPORT dst: rADDR:rPORT
+---------+
| NAT |
+---------+ +-----------+ +---------+
| |---------->| |--------->| |
| Gateway | | Mapping | | Relay |
| |<----------| |<---------| |
+---------+ +-----------+ +---------+
| |
+---------+
Multicast Data Multicast Data
src: rADDR:rPORT src: rADDR:rPORT
Bumgardner Expires December 14, 2012 [Page 29]
Internet-Draft AMT June 2012
dst: iADDR:iPORT dst: eADDR:ePORT
Network Address Translation in AMT
AMT provides automatic NAT traversal by using the source IP address
and UDP port carried by the Membership Update message as received at
the relay as the destination address for any Multicast Data messages
the relay sends back as a result.
The NAT mapping created by a Membership Update message will
eventually expire unless it is refreshed by a passing message. This
refresh will occur each time the gateway performs the periodic update
required to refresh group state within the relay (See
Section 4.2.1.2).
4.2.2.3. UDP Encapsulation
Gateway Relay
IP:IGMP IP:IGMP
| AMT:IP:IGMP AMT:IP:IGMP |
| | | |
| | IP:UDP:AMT:IP:IGMP | |
_______ | ___ | ______ | ______ | ___ | _______
|IGMP|IP| v |AMT| v |UDP|IP| v |IP|UDP| v |AMT| v |IP|IGMP|
| | | | | | | | | | | | | | | |
| |<------------------------------------------------------->| |
|____| | | | | | | | | | | | | |____|
| |<--------------------------------------------------| |
|_______| ^ |___| ^ |___|__| ^ |__|___| ^ |___| ^ |_______|
| | | | |
IP AMT:IP IP:UDP:AMT:IP AMT:IP IP
AMT Encapsulation
The IGMP and MLD messages used in AMT are exchanged as complete IP
datagrams. These IP datagrams are encapsulated in AMT messages that
are transmitted using UDP. The same holds true for multicast traffic
- each multicast IP datagram or datagram fragment that arrives at the
relay is encapsulated in an AMT message and transmitted to one or
more gateways via UDP.
The IP protocol of the encapsulated packets need not match the IP
protocol used to send the AMT messages. AMT messages sent via IPv4
may carry IPv6/MLD packets and AMT messages sent via IPv6 may carry
IPv4/IGMP packets.
The checksum field contained in the UDP header of the messages
Bumgardner Expires December 14, 2012 [Page 30]
Internet-Draft AMT June 2012
requires special consideration. Of primary concern is the cost of
computing a checksum on each replicated multicast packet after it is
encapsulated for delivery to a gateway. Many routing/forwarding
platforms do not possess the capability to compute checksums on UDP
encapsulated packets as they may not have access to the entire
datagram.
To avoid placing an undue burden on the relay platform, the protocol
specifically allows zero-valued UDP checksums on the multicast data
messages. This is not an issue in UDP over IPv4 as the UDP checksum
field may be set to zero. However, this is a problem for UDP over
IPv6 as that protocol requires a valid, non-zero checksum in UDP
datagrams [RFC2460]. Messages sent over IPv6 with a UDP checksum of
zero may fail to reach the gateway. This is a well known issue for
UDP-based tunneling protocols that is described
[I-D.ietf-6man-udpzero]. A recommended solution is described in
[I-D.ietf-6man-udpchecksums].
Bumgardner Expires December 14, 2012 [Page 31]
Internet-Draft AMT June 2012
5. Protocol Description
This section provides a normative description of the AMT protocol.
5.1. Protocol Messages
The AMT protocol defines seven message types for control and
encapsulation. These messages are assigned the following names and
numeric identifiers:
+--------------+---------------------+
| Message Type | Message Name |
+--------------+---------------------+
| 1 | Relay Discovery |
| | |
| 2 | Relay Advertisement |
| | |
| 3 | Request |
| | |
| 4 | Membership Query |
| | |
| 5 | Membership Update |
| | |
| 6 | Multicast Data |
| | |
| 7 | Teardown |
+--------------+---------------------+
These messages are exchanged as IPv4 or IPv6 UDP datagrams.
5.1.1. Relay Discovery
A Relay Discovery message is used to solicit a response from a relay
in the form of a Relay Advertisement message.
The UDP/IP datagram containing this message MUST carry a valid, non-
zero UDP checksum and carry the following IP address and UDP port
values:
Source IP Address - The IP address of the gateway interface on which
the gateway will listen for a relay response. Note: The value of
this field may be changed as a result of network address
translation before arriving at the relay.
Source UDP Port - The UDP port number on which the gateway will
listen for a relay response. Note: The value of this field may be
changed as a result of network address translation before arriving
at the relay.
Bumgardner Expires December 14, 2012 [Page 32]
Internet-Draft AMT June 2012
Destination IP Address - An anycast or unicast IP address, i.e., the
Relay Discovery Address advertised by a relay.
Destination UDP Port - The IANA-assigned AMT port number.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| V=0 |Type=1 | Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Discovery Nonce |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Relay Discovery Message Format
5.1.1.1. Version (V)
The protocol version number for this message is 0.
5.1.1.2. Type
The type number for this message is 1.
5.1.1.3. Reserved
Reserved bits that MUST be set to zero by the gateway and ignored by
the relay.
5.1.1.4. Discovery Nonce
A 32-bit random value generated by the gateway and echoed by the
relay in a Relay Advertisement message. This value is used by the
gateway to correlate Relay Advertisement messages with Relay
Discovery messages. Discovery nonce generation is described in
Section 5.2.3.4.5.
5.1.2. Relay Advertisement
The Relay Advertisement message is used to supply a gateway with a
unicast IP address of a relay. A relay sends this message to a
gateway when it receives a Relay Discovery message from that gateway.
The UDP/IP datagram containing this message MUST carry a valid, non-
zero UDP checksum and carry the following IP address and UDP port
values:
Bumgardner Expires December 14, 2012 [Page 33]
Internet-Draft AMT June 2012
Source IP Address - The destination IP address carried by the Relay
Discovery message (i.e., the Relay Discovery Address advertised by
the relay).
Source UDP Port - The destination UDP port carried by the Relay
Discovery message (i.e., the IANA-assigned AMT port number).
Destination IP Address - The source IP address carried by the Relay
Discovery message. Note: The value of this field may be changed
as a result of network address translation before arriving at the
gateway.
Destination UDP Port - The source UDP port carried by the Relay
Discovery message. Note: The value of this field may be changed
as a result of network address translation before arriving at the
gateway.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| V=0 |Type=2 | Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Discovery Nonce |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
~ Relay Address (IPv4 or IPv6) ~
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Relay Advertisement Message Format
5.1.2.1. Version (V)
The protocol version number for this message is 0.
5.1.2.2. Type
The type number for this message is 2.
5.1.2.3. Reserved
Reserved bits that MUST be set to zero by the relay and ignored by
the gateway.
Bumgardner Expires December 14, 2012 [Page 34]
Internet-Draft AMT June 2012
5.1.2.4. Discovery Nonce
A 32-bit value copied from the Discovery Nonce field
(Section 5.1.1.4) contained in the Relay Discovery message. The
gateway uses this value to match a Relay Advertisement to a Relay
Discovery message.
5.1.2.5. Relay Address
The unicast IPv4 or IPv6 address of the relay. A gateway uses the
length of the UDP datagram containing the Relay Advertisement message
to determine the address family; i.e., length - 8 = 4 (IPv4) or 16
(IPv6). The relay returns an IP address for the protocol used to
send the Relay Discovery message, i.e., an IPv4 relay address for an
IPv4 discovery address or an IPv6 relay address for an IPv6 discovery
address.
5.1.3. Request
A gateway sends a Request message to a relay to solicit a Membership
Query response.
The successful delivery of this message marks the start of the first
stage in the three-way handshake used to create or update state
within a relay.
The UDP/IP datagram containing this message MUST carry a valid, non-
zero UDP checksum and carry the following IP address and UDP port
values:
Source IP Address - The IP address of the gateway interface on which
the gateway will listen for a response from the relay. Note: The
value of this field may be changed as a result of network address
translation before arriving at the relay.
Source UDP Port - The UDP port number on which the gateway will
listen for a response from the relay. Note: The value of this
field may be changed as a result of network address translation
before arriving at the relay.
Destination IP Address - The unicast IP address of the relay.
Destination UDP Port - The IANA-assigned AMT port number.
Bumgardner Expires December 14, 2012 [Page 35]
Internet-Draft AMT June 2012
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| V=0 |Type=3 | Reserved |P| Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Request Nonce |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Request Message Format
5.1.3.1. Version (V)
The protocol version number for this message is 0.
5.1.3.2. Type
The type number for this message is 3.
5.1.3.3. Reserved
Reserved bits that MUST be set to zero by the gateway and ignored by
the relay.
5.1.3.4. P Flag
The "P" flag is set to indicate which group membership protocol the
gateway wishes the relay to use in the Membership Query response:
Value Meaning
0 The relay MUST respond with a Membership Query message that
contains an IPv4 packet carrying an IGMPv3 general query
message.
1 The relay MUST respond with a Membership Query message that
contains an IPv6 packet carrying an MLDv2 general query
message.
5.1.3.5. Request Nonce
A 32-bit random value generated by the gateway and echoed by the
relay in a Membership Query message. This value is used by the relay
to compute the Response MAC value and is used by the gateway to
correlate Membership Query messages with Request messages. Request
nonce generation is described in Section 5.2.3.5.6.
Bumgardner Expires December 14, 2012 [Page 36]
Internet-Draft AMT June 2012
5.1.4. Membership Query
A relay sends a Membership Query message to a gateway to solicit a
Membership Update response, but only after receiving a Request
message from the gateway.
The successful delivery of this message to a gateway marks the start
of the second-stage in the three-way handshake used to create or
update tunnel state within a relay.
The UDP/IP datagram containing this message MUST carry a valid, non-
zero UDP checksum and carry the following IP address and UDP port
values:
Source IP Address - The destination IP address carried by the
Request message (i.e., the unicast IP address of the relay).
Source UDP Port - The destination UDP port carried by the Request
message (i.e., the IANA-assigned AMT port number).
Destination IP Address - The source IP address carried by the
Request message. Note: The value of this field may be changed as
a result of network address translation before arriving at the
gateway.
Destination UDP Port - The source UDP port carried by the Request
message. Note: The value of this field may be changed as a result
of network address translation before arriving at the gateway.
Bumgardner Expires December 14, 2012 [Page 37]
Internet-Draft AMT June 2012
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| V=0 |Type=4 | Reserved |L|G| Response MAC |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Request Nonce |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
| Encapsulated General Query Message |
~ IPv4:IGMPv3(Membership Query) ~
| IPv6:MLDv2(Listener Query) |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Gateway Port Number | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ +
| |
+ +
| Gateway IP Address (IPv4 or IPv6) |
+ +
| |
+ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Membership Query Message Format
5.1.4.1. Version (V)
The protocol version number for this message is 0.
5.1.4.2. Type
The type number for this message is 4.
5.1.4.3. Reserved
Reserved bits that MUST be set to zero by the relay and ignored by
the gateway.
5.1.4.4. Limit (L) Flag
A 1-bit flag set to 1 to indicate that the relay is NOT accepting
Membership Update messages from new gateway tunnel endpoints and that
it will ignore any that are. A value of 0 has no special
significance - the relay may or may not be accepting Membership
Update messages from new gateway tunnel endpoints. A gateway checks
Bumgardner Expires December 14, 2012 [Page 38]
Internet-Draft AMT June 2012
this flag before attempting to create new group subscription state on
the relay to determine whether it should restart relay discovery. A
gateway that has already created group subscriptions on the relay may
ignore this flag. Support for this flag is RECOMMENDED.
5.1.4.5. Gateway Address (G) Flag
A 1-bit flag set to 0 to indicate that the message does NOT carry the
Gateway Port and Gateway IP Address fields, and 1 to indicate that it
does. A relay implementation that supports the optional teardown
procedure (See Section 5.3.3.5) SHOULD set this flag and the Gateway
Address field values. If a relay sets this flag, it MUST also
include the Gateway Address fields in the message. A gateway
implementation that does not support the optional teardown procedure
(See Section 5.2.3.7) MAY ignore this flag and the Gateway Address
fields if they are present.
5.1.4.6. Response MAC
A 48-bit source authentication hash generated by the relay as
described in Section 5.3.5. The gateway echoes this value in
subsequent Membership Update messages to allow the relay to verify
that the sender of a Membership Update message was the intended
receiver of a Membership Query sent by the relay.
5.1.4.7. Request Nonce
A 32-bit value copied from the Request Nonce field (Section 5.1.3.5)
carried by a Request message. The relay will have included this
value in the Response MAC hash computation. The gateway echoes this
value in subsequent Membership Update messages. The gateway also
uses this value to match a Membership Query to a Request message.
5.1.4.8. Encapsulated General Query Message
An IP-encapsulated IGMP or MLD message generated by the relay. This
field will contain one of the following IP datagrams:
IPv4:IGMPv3 Membership Query
IPv6:MLDv2 Listener Query
The source address carried by the query message should be set as
described in Section 5.3.3.3.
The Querier's Query Interval Code (QQIC) field in the general query
is used by a relay to specify the time offset a gateway should use to
schedule a new three-way handshake to refresh the group membership
Bumgardner Expires December 14, 2012 [Page 39]
Internet-Draft AMT June 2012
state within the relay (current time + Query Interval).
The Querier's Robustness Variable (QRV) field in the general query is
used by a relay to specify the number of times a gateway should
retransmit unsolicited membership reports, encapsulated within
Membership Update messages, and optionally, the number of times to
send a Teardown message.
5.1.4.9. Gateway Address Fields
The Gateway Port Number and Gateway Address fields are present in the
Membership Query message if, and only if, the "G" flag is set.
A gateway need not parse the encapsulated IP datagram to determine
the position of these fields within the UDP datagram containing the
Membership Query message - if the G-flag is set, the gateway may
simply subtract the total length of the fields (18 bytes) from the
total length of the UDP datagram to obtain the offset.
5.1.4.9.1. Gateway Port Number
A 16-bit UDP port containing a UDP port value.
The Relay sets this field to the value of the UDP source port of the
Request message that triggered the Query message.
5.1.4.9.2. Gateway IP Address
A 16-byte IP address that, when combined with the value contained in
the Gateway Port Number field, forms the gateway endpoint address
that the relay will use to identify the tunnel instance, if any,
created by a subsequent Membership Update message. This field may
contain an IPv6 address or an IPv4 address stored as an IPv4-
compatible IPv6 address, where the IPv4 address is prefixed with 96
bits set to zero (See [RFC4291]). This address must match that used
by the relay to compute the value stored in the Response MAC field.
5.1.5. Membership Update
A gateway sends a Membership Update message to a relay to report a
change in group membership state, or to report the current group
membership state in response to receiving a Membership Query message.
The gateway encapsulates the IGMP or MLD message as an IP datagram
within a Membership Update message and sends it to the relay, where
it may (see below) be decapsulated and processed by the relay to
update group membership and forwarding state.
A gateway cannot send a Membership Update message until a receives a
Bumgardner Expires December 14, 2012 [Page 40]
Internet-Draft AMT June 2012
Membership Query from a relay because the gateway must copy the
Request Nonce and Response MAC values carried by a Membership Query
into any subsequent Membership Update messages it sends back to that
relay. These values are used by the relay to verify that the sender
of the Membership Update message was the recipient of the Membership
Query message from which these values were copied.
The successful delivery of this message to the relay marks the start
of the final stage in the three-way handshake. This stage concludes
when the relay successfully verifies that sender of the Membership
Update message was the recipient of a Membership Query message sent
earlier. At this point, the relay may proceed to process the
encapsulated IGMP or MLD message to create or update group membership
and forwarding state on behalf of the gateway.
The UDP/IP datagram containing this message MUST carry a valid, non-
zero UDP checksum and carry the following IP address and UDP port
values:
Source IP Address - The IP address of the gateway interface on which
the gateway will listen for Multicast Data messages from the
relay. The address must be the same address used to send the
initial Request message or the message will be ignored. Note: The
value of this field may be changed as a result of network address
translation before arriving at the relay.
Source UDP Port - The UDP port number on which the gateway will
listen for Multicast Data messages from the relay. This port must
be the same port used to send the initial Request message or the
message will be ignored. Note: The value of this field may be
changed as a result of network address translation before arriving
at the relay.
Destination IP Address - The unicast IP address of the relay.
Destination UDP Port - The IANA-assigned AMT UDP port number.
Bumgardner Expires December 14, 2012 [Page 41]
Internet-Draft AMT June 2012
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| V=0 |Type=5 | Reserved | Response MAC |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Request Nonce |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
| Encapsulated Group Membership Update Message |
~ IPv4:IGMP(Membership Report|Leave Group) ~
| IPv6:MLD(Listener Report|Listener Done) |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Membership Update Message Format
5.1.5.1. Version (V)
The protocol version number for this message is 0.
5.1.5.2. Type
The type number for this message is 5.
5.1.5.3. Reserved
Reserved bits that MUST be set to zero by the gateway and ignored by
the relay.
5.1.5.4. Response MAC
A 48-bit value copied from the Response MAC field (Section 5.1.4.6)
in a Membership Query message. Used by the relay to perform source
authentication.
5.1.5.5. Request Nonce
A 32-bit value copied from the Request Nonce field in a Request or
Membership Query message. Used by the relay to perform source
authentication.
5.1.5.6. Encapsulated Group Membership Update Message
An IP-encapsulated IGMP or MLD message produced by the host-mode IGMP
or MLD protocol running on a gateway pseudo-interface. This field
will contain of one of the following IP datagrams:
Bumgardner Expires December 14, 2012 [Page 42]
Internet-Draft AMT June 2012
IPv4:IGMPv2 Membership Report
IPv4:IGMPv2 Leave Group
IPv4:IGMPv3 Membership Report
IPv6:MLDv1 Multicast Listener Report
IPv6:MLDv1 Multicast Listener Done
IPv6:MLDv2 Multicast Listener Report
The source address carried by the message should be set as described
in Section 5.2.1.
5.1.6. Multicast Data
A relay sends a Multicast Data message to deliver an multicast IP
datagram or datagram fragment to a gateway.
The checksum field in the UDP header of this message MAY contain a
value of zero when sent over IPv4 but SHOULD, if possible, contain a
valid, non-zero value when sent over IPv6 (See Section 4.2.2.3).
The UDP/IP datagram containing this message MUST carry the following
IP address and UDP port values:
Source IP Address - The unicast IP address of the relay.
Source UDP Port - The IANA-assigned AMT port number.
Destination IP Address - A tunnel endpoint IP address, i.e., the
source IP address carried by the Membership Update message sent by
a gateway to indicate an interest in receiving the multicast
packet. Note: The value of this field may be changed as a result
of network address translation before arriving at the gateway.
Destination UDP Port - A tunnel endpoint UDP port, i.e., the source
UDP port carried by the Membership Update message sent by a
gateway to indicate an interest in receiving the multicast packet.
Note: The value of this field may be changed as a result of
network address translation before arriving at the gateway.
Bumgardner Expires December 14, 2012 [Page 43]
Internet-Draft AMT June 2012
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| V=0 |Type=6 | Reserved | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ +
| |
~ IP Multicast Packet ~
| |
+ - - - - - - - - - - - - - - - - - - - - - - - -+
| : : : :
+-+-+-+-+-+-+-+-+- - - - - - - - - - - - - - - - - - - - - - - -
Multicast Data Message Format
5.1.6.1. Version (V)
The protocol version number for this message is 0.
5.1.6.2. Type
The type number for this message is 6.
5.1.6.3. Reserved
Bits that MUST be set to zero by the relay and ignored by the
gateway.
5.1.6.4. IP Multicast Data
A complete IPv4 or IPv6 multicast datagram or datagram fragment.
5.1.7. Teardown
A gateway sends a Teardown message to a relay to request that it stop
sending Multicast Data messages to a tunnel endpoint created by an
earlier Membership Update message. A gateway sends this message when
it detects that a Request message sent to the relay carries an
address that differs from that carried by a previous Request message.
The gateway uses the Gateway IP Address and Gateway Port Number
Fields in the Membership Query message to detect these address
changes.
To provide backwards compatibility with early implementations of the
AMT protocol, support for this message and associated procedures is
considered OPTIONAL - gateways are not required to send this message
and relays are not required to act upon it.
The UDP/IP datagram containing this message MUST carry a valid, non-
Bumgardner Expires December 14, 2012 [Page 44]
Internet-Draft AMT June 2012
zero UDP checksum and carry the following IP address and UDP port
values:
Source IP Address - The IP address of the gateway interface used to
send the message. This address may differ from that used to send
earlier messages. Note: The value of this field may be changed as
a result of network address translation before arriving at the
relay.
Source UDP Port - The UDP port number. This port number may differ
from that used to send earlier messages. Note: The value of this
field may be changed as a result of network address translation
before arriving at the relay.
Destination IP Address - The unicast IP address of the relay.
Destination UDP Port - The IANA-assigned AMT port number.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| V=0 |Type=7 | Reserved | Response MAC |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Request Nonce |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Gateway Port Number | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ +
| |
+ +
| Gateway IP Address (IPv4 or IPv6) |
+ +
| |
+ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Membership Teardown Message Format
5.1.7.1. Version (V)
The protocol version number for this message is 0.
5.1.7.2. Type
The type number for this message is 7.
Bumgardner Expires December 14, 2012 [Page 45]
Internet-Draft AMT June 2012
5.1.7.3. Reserved
Reserved bits that MUST be set to zero by the gateway and ignored by
the relay.
5.1.7.4. Response MAC
A 48-bit value copied from the Response MAC field (Section 5.1.4.6)
in the last Membership Query message the relay sent to the gateway
endpoint address of the tunnel to be torn down. The gateway endpoint
address is provided by the Gateway IP Address and Gateway Port Number
fields carried by the Membership Query message. The relay validates
the Teardown message by comparing this value with one computed from
the Request Nonce, Gateway Port Number and Gateway IP Address fields
(just as it does in the Membership Update message).
5.1.7.5. Request Nonce
A 32-bit value copied from the Request Nonce field (Section 5.1.4.7)
in the last Membership Query message the relay sent to the gateway
endpoint address of the tunnel to be torn down. The gateway endpoint
address is provided by the Gateway IP Address and Gateway Port Number
fields carried by the Membership Query message. This value must
match that used by the relay to compute the value stored in the
Response MAC field.
5.1.7.6. Gateway Port Number
A 16-bit UDP port number that, when combined with the value contained
in the Gateway IP Address field, forms the tunnel endpoint address
that the relay will use to identify the tunnel instance to tear down.
The relay provides this value to the gateway using the Gateway Port
Number field (Section 5.1.4.9.1) in a Membership Query message. This
port number must match that used by the relay to compute the value
stored in the Response MAC field.
5.1.7.7. Gateway IP Address
A 16-byte IP address that, when combined with the value contained in
the Gateway Port Number field, forms the tunnel endpoint address that
the relay will used to identify the tunnel instance to tear down.
The relay provides this value to the gateway using the Gateway IP
Address field (Section 5.1.4.9.2) in a Membership Query message.
This field may contain an IPv6 address or an IPv4 address stored as
an IPv4-compatible IPv6 address, where the IPv4 address is prefixed
with 96 bits set to zero (See [RFC4291]). This address must match
that used by the relay to compute the value stored in the Response
MAC field.
Bumgardner Expires December 14, 2012 [Page 46]
Internet-Draft AMT June 2012
5.2. Gateway Operation
The following sections describe gateway implementation requirements.
A non-normative discussion of gateway operation may be found in
Section 4.2.
5.2.1. IP/IGMP/MLD Protocol Requirements
Gateway operation requires a subset of host mode IPv4/IGMP and IPv6/
MLD functionality to provide group membership tracking, general query
processing, and report generation. A gateway MAY use IGMPv2 (ASM),
IGMPv3 (ASM and SSM), MLDv1 (ASM) or MLDv2 (ASM and SSM).
An application with embedded gateway functionality must provide its
own implementation of this subset of the IPv4/IGMP and IPv6/MLD
protocols. The service interface used to manipulate group membership
state need not match that described in the IGMP and MLD
specifications, but the actions taken as a result SHOULD be similar
to those described in Section 5.1 of [RFC3376] and Section 6.1 of
[RFC3810]. The gateway application will likely need to implement
many of the same functions as a host IP stack, including checksum
verification, dispatching, datagram filtering and forwarding, and IP
encapsulation/decapsulation.
The IP-encapsulated IGMP messages generated by the gateway IPv4/IGMP
implementation MUST conform to the description found in Section 4 of
[RFC3376]. These datagrams MUST possess the IP headers, header
options and header values called for in [RFC3376], with the following
exception; the source IP address for an IGMP report datagram MAY be
set to the "unspecified" address (all octets are zero ) but SHOULD be
set to an address in the address range specifically assigned by IANA
for use in the IGMP messages sent from a gateway to a relay (i.e.
154.7.1.2 through 154.7.1.254 as described in Section 7). This
exception is made because the gateway pseudo-interface might not
possess an assigned address, and even if such an address exists, that
address would not be a valid link-local source address on any relay
interface. The rationale for using the aforementioned source
addresses is primarily one of convenience - a relay will accept an
IGMP report carried by a Membership Update message regardless of the
source address it carries. See Section 5.3.1.
The IP-encapsulated MLD messages generated by the gateway IPv6/MLD
implementation MUST conform to the description found in Section 5 of
[RFC3810]. These datagrams MUST possess the IP headers, header
options and header values called for in [RFC3810], with the following
exception; the source IP address for an MLD report datagram MAY be
set to the "unspecified" address (all octets are zero ) but SHOULD be
set to an IPv6 link-local address in the range FE80::/64 excluding
Bumgardner Expires December 14, 2012 [Page 47]
Internet-Draft AMT June 2012
FE80::1 and FE80::2. This exception is made because the gateway
pseudo-interface might not possess a valid IPv6 address. As with
IGMP, a relay will accept an MLD report carried by a Membership
Update message regardless of the source address it carries. See
Section 5.3.1.
The gateway IGMP/MLD implementation SHOULD retransmit unsolicited
membership state-change reports and merge new state change reports
with pending reports as described in Section 5.1 of [RFC3376] and
Section 6.1 of [RFC3810]. The number of retransmissions is specified
by the relay in the Querier's Robustness Variable (QRV) field in the
last general query forwarded by the pseudo-interface.
The gateway IGMP/MLD implementation SHOULD handle general query
messages as described in Section 5.2 of [RFC3376] and Section 6.2 of
[RFC3810], but MAY ignore the Max Resp Code field value and generate
a current state report without any delay.
An IPv4 gateway implementation MUST accept IPv4 datagrams that carry
the general query variant of the IGMPv3 Membership Query message, as
described in Section 4 of [RFC3376]. The gateway MUST accept the
IGMP datagram regardless of the IP source address carried by that
datagram.
An IPv6 gateway implementation MUST accept IPv6 datagrams that carry
the general query variant of the MLDv2 Multicast Listener Query
message, as described in Section 5 of [RFC3810]. The gateway MUST
accept the MLD datagram regardless of the IP source address carried
by that datagram.
5.2.2. Pseudo-Interface Configuration
A gateway host may possess or create multiple gateway pseudo-
interfaces, each with a unique configuration that describes a binding
to a specific IP protocol, relay address, relay discovery address or
upstream network interface.
5.2.2.1. Relay Discovery Address
If a gateway implementation uses AMT relay discovery to obtain a
relay address, it must first be supplied with a relay discovery
address. The relay discovery address may be an anycast or unicast
address. A gateway implementation may rely on a static address
assignment or some form of dynamic address discovery. This
specification does not require that a gateway implementation use any
particular method to obtain a relay discovery address - an
implementation may employ any method that returns a suitable relay
discovery address.
Bumgardner Expires December 14, 2012 [Page 48]
Internet-Draft AMT June 2012
5.2.2.2. Relay Address
Before a gateway implementation can execute the AMT protocol to
request and receive multicast traffic, it must be supplied with a
unicast relay address. A gateway implementation may rely on static
address assignment or support some form of dynamic address discovery.
This specification does not require the use of any particular method
to obtain a relay address - an implementation may employ any method
that returns a suitable relay address.
5.2.2.3. Upstream Interface Selection
A gateway host that possesses multiple network interfaces or
addresses may allow for an explicit selection of the interface to use
when communicating with a relay. The selection might be made to
satisfy connectivity, tunneling or IP protocol requirements.
5.2.2.4. Optional Retransmission Parameters
A gateway implementation that supports retransmission MAY require the
following information:
Discovery Timeout
Initial time to wait for a response to a Relay Discovery message.
Maximum Relay Discovery Retransmission Count
Maximum number of Relay Discovery retransmissions to allow before
terminating relay discovery and reporting an error.
Request Timeout
Initial time to wait for a response to a Request message.
Maximum Request Retransmission Count
Maximum number of Request retransmissions to allow before
abandoning a relay and restarting relay discovery or reporting an
error.
Maximum Retries Count For "Destination Unreachable"
The maximum number of times a gateway should attempt to send the
same Request or Membership Update message after receiving an ICMP
"Destination Unreachable".
5.2.3. Gateway Service
In the following descriptions, a gateway pseudo interface is treated
as a passive entity managed by a gateway service. The gateway
pseudo-interface provides the state and the gateway service provides
the processing. The term "gateway" is used when describing service
Bumgardner Expires December 14, 2012 [Page 49]
Internet-Draft AMT June 2012
behavior with respect to a single pseudo-interface.
5.2.3.1. Startup
When a gateway pseudo-interface is started, the gateway service
begins listening for AMT messages sent to the UDP endpoint(s)
associated with the pseudo-interface and for any locally-generated
IGMP/MLD messages passed to the pseudo-interface. The handling of
these messages is described below.
When the pseudo-interface is enabled, the gateway service MAY:
o Optionally execute the relay discovery procedure described in
Section 5.2.3.4.
o Optionally execute the membership query procedure described in
Section 5.2.3.5 to start the periodic membership update cycle.
5.2.3.2. Handling AMT Messages
A gateway MUST ignore any datagram it receives that cannot be
interpreted as a Relay Advertisement, Membership Query, or Multicast
Data message. The handling of Relay Advertisement, Membership Query,
and Multicast Data messages is addressed in the sections that follow.
While listening for AMT messages, a gateway may be notified that an
ICMP Destination Unreachable message was received as a result of an
AMT message transmission. Handling of ICMP Destination Unreachable
messages is described in Section 5.2.3.9.
5.2.3.3. Handling Multicast Data Messages
A gateway may receive Multicast Data messages after it sends a
Membership Update message to a relay that adds a group subscription.
The gateway may continue to receive Multicast Data messages long
after the gateway sends a Membership Update message that deletes
existing group subscriptions. The gateway MUST be prepared to
receive these messages at any time, but MAY ignore them or discard
their contents if the gateway no longer has any interest in receiving
the multicast datagrams contained within them.
A gateway MUST ignore a Multicast Data message if it fails to satisfy
any of the following requirements:
o The source IP address and UDP port carried by the Multicast Data
message MUST be equal to the destination IP address and UDP port
carried by the matching Membership Update message (i.e., the
current relay address).
Bumgardner Expires December 14, 2012 [Page 50]
Internet-Draft AMT June 2012
o The destination address carried by the encapsulated IP datagram
MUST fall within the multicast address allocation assigned to the
relevant IP protocol, i.e., 224.0.0.0/4 for IPv4 and FF00::/8 for
IPv6.
The gateway extracts the encapsulated IP datagram and forwards it to
the local IP protocol implementation for checksum verification,
fragmented datagram reassembly, source and group filtering, and
transport-layer protocol processing.
Because AMT uses UDP encapsulation to deliver multicast datagrams to
gateways, it qualifies as a tunneling protocol subject to the
limitations described in [I-D.ietf-6man-udpzero]. If supported, a
gateway SHOULD employ the solution described in
[I-D.ietf-6man-udpchecksums] to ensure that the local IP stack does
not discard IPv6 datagrams with zero checksums. If Multicast Data
message datagrams are processed directly within the gateway (instead
of the host IP stack), the gateway MUST NOT discard any of these
datagrams because they carry a UDP checksum of zero.
5.2.3.4. Relay Discovery Procedure
This section describes gateway requirements related to the relay
discovery message sequence described in Section 4.2.1.1.
5.2.3.4.1. Starting Relay Discovery
A gateway may start or restart the relay discovery procedure in
response to the following events:
o When a gateway pseudo-interface is started (enabled).
o When the gateway wishes to report a group subscription when none
currently exist.
o Before sending the next Request message in a membership update
cycle, i.e., each time the query timer expires (see below).
o After the gateway fails to receive a response to a Request
message.
o After the gateway receives a Membership Query message with the
L-flag set to 1.
Bumgardner Expires December 14, 2012 [Page 51]
Internet-Draft AMT June 2012
5.2.3.4.2. Sending a Relay Discovery Message
A gateway sends a Relay Discovery message to a relay to start the
relay discovery process.
The gateway MUST send the Relay Discovery message using the current
Relay Discovery Address and IANA-assigned UDP port number as the
destination. The Discovery Nonce value in the Relay Discovery
message MUST be computed as described in Section 5.2.3.4.5.
The gateway MUST save a copy of Relay Discovery message or save the
Discovery Nonce value for possible retransmission and verification of
a Relay Advertisement response.
When a gateway sends a Relay Discovery message, it may be notified
that an ICMP Destination Unreachable message was received as a result
of an earlier AMT message transmission. Handling of ICMP Destination
Unreachable messages is described in Section 5.2.3.9.
5.2.3.4.3. Waiting for a Relay Advertisement Message
A gateway MAY retransmit a Relay Discovery message if it does not
receive a matching Relay Advertisement message within some timeout
period. If the gateway retransmits the message multiple times, the
timeout period SHOULD be adjusted to provide an random exponential
back-off. The RECOMMENDED timeout is a random value in the range
[initial_timeout, MIN(initial_timeout * 2^retry_count,
maximum_timeout)], with a RECOMMENDED initial_timeout of 1 second and
a RECOMMENDED maximum_timeout of 120 seconds (which is the
recommended minimum NAT mapping timeout described in [RFC4787]).
5.2.3.4.4. Handling a Relay Advertisement Message
When a gateway receives a Relay Advertisement message it must first
determine whether it should accept or ignore the message. A gateway
MUST ignore a Relay Advertisement message if it fails to satisfy any
of the following requirements:
o The gateway MUST be waiting for a Relay Advertisement message.
o The Discovery Nonce value contained in the Relay Advertisement
message MUST equal to the Discovery Nonce value contained in the
Relay Discovery message.
o The source IP address and UDP port of the Relay Advertisement
message MUST equal to the destination IP address and UDP port of
the matching Relay Discovery message.
Bumgardner Expires December 14, 2012 [Page 52]
Internet-Draft AMT June 2012
Once a gateway receives a Relay Advertisement response to a Relay
Discovery message, it SHOULD ignore any other Relay Advertisements
that arrive on the AMT interface until it sends a new Relay Discovery
message.
If a gateway executes the relay discovery procedure at the start of
each membership update cycle and the relay address returned in the
latest Relay Advertisement message differs from the address returned
in a previous Relay Advertisement message, then the gateway SHOULD
send a Teardown message (if supported) to the old relay address,
using information from the last Membership Query message received
from that relay, as described in Section 5.2.3.7. This behavior is
illustrated in the following diagram.
Bumgardner Expires December 14, 2012 [Page 53]
Internet-Draft AMT June 2012
Gateway Relay-1
------- -------
: :
Query Expired | |
Timer (QT)-------->| |
| Relay Discovery |
|------------------->|
| |
| Relay Advertisement|
|<-------------------|
| |
| Request |
|------------------->|
| |
| Membership Query |
|<===================|
Start | |
(QT)<--------| Membership Update |
|===================>|
| |
~ ~ Relay-2
Expired | | -------
(QT)-------->| | :
| Relay Discovery | |
|------------------------------------>|
| | |
| Relay Advertisement| |
|<------------------------------------|
| | |
| Teardown | |
|------------------->| |
| | |
| Request | |
|------------------------------------>|
| | |
| Membership Query | |
|<====================================|
Start | | |
(QT)<--------| Membership Update | |
|====================================>|
| | |
: : :
Teardown After Relay Address Change
Bumgardner Expires December 14, 2012 [Page 54]
Internet-Draft AMT June 2012
5.2.3.4.5. Discovery Nonce Generation
The discovery nonce MUST be a random, non-zero, 32-bit value, and if
possible, SHOULD be computed using a cryptographically secure pseudo
random number generator. A new nonce SHOULD be generated each time
the gateway restarts the relay discovery process. The same nonce
SHOULD be used when retransmitting a Relay Discovery message.
5.2.3.5. Membership Query Procedure
This section describes gateway requirements related to the membership
update message sequence described in Section 4.2.1.2.
5.2.3.5.1. Starting the Membership Update Cycle
A gateway may send a Request message to start a membership update
cycle (following the optional relay discovery procedure) in response
to the following events:
o When the gateway pseudo-interface is activated.
o When the gateway wishes to report a group subscription when none
currently exist.
Starting the membership update cycle when a gateway pseudo-interface
is started provides several benefits:
o Better performance by allowing state-change reports to be sent as
they are generated, thus minimizing the time to join.
o More robustness by relying on unsolicited state-change reports to
update group membership state rather than the current-state
reports generated by the membership update cycle. Unsolicited
state-change reports are typically retransmitted multiple times
while current-state reports are not.
o Simplified implementation by eliminating any need to queue IGMP/
MLD messages for delivery after a Membership Query is received,
since the IGMP/MLD state-change messages may be sent as they are
generated.
However, this approach places an additional load on relays as a
gateway will send periodic requests even when it has no multicast
subscriptions. To reduce load on a relay, a gateway SHOULD only send
a Membership Update message while it has active group subscriptions.
A relay will still need to compute a Response MAC for each Request,
but will not be required to recompute it a second time to
authenticate a Membership Update message that contains no
Bumgardner Expires December 14, 2012 [Page 55]
Internet-Draft AMT June 2012
subscriptions.
5.2.3.5.2. Sending a Request Message
A gateway sends a Request message to a relay to solicit a Membership
Query response and start the membership update cycle.
A gateway constructs a Request message containing a Request Nonce
value computed as described in Section 5.2.3.5.6. The gateway MUST
set the "P" flag in the Request message to identify the protocol the
gateway wishes the relay to use for the general query response.
A gateway MUST send a Request message using the current Relay Address
and IANA-assigned AMT port number as the destination.
A gateway MUST save a copy of the Request message or save the Request
Nonce and P-flag values for possible retransmission and verification
of a Membership Query response.
When a gateway sends a Request message, it may be notified that an
ICMP Destination Unreachable message was received as a result of an
earlier AMT message transmission. Handling of ICMP Destination
Unreachable messages is described in Section 5.2.3.9.
5.2.3.5.3. Waiting for a Membership Query Message
A gateway MAY retransmit a Request message if it does not receive a
matching Membership Query message within some timeout period. If the
gateway retransmits the message multiple times, the timeout period
SHOULD be adjusted to provide an random exponential back-off. The
RECOMMENDED timeout is a random value in the range [initial_timeout,
MIN(initial_timeout * 2^retry_count, maximum_timeout)], with a
RECOMMENDED initial_timeout of 1 second and a RECOMMENDED
maximum_timeout of 120 seconds (which is the recommended minimum NAT
mapping timeout described in [RFC4787]).
If a gateway that uses relay discovery does not receive a Membership
Query within a specified time period or after a specified number of
retries, the gateway SHOULD stop waiting for a Membership Query
message and restart relay discovery to locate another relay.
5.2.3.5.4. Handling a Membership Query Message
When a gateway receives a Membership Query message it must first
determine whether it should accept or ignore the message. A gateway
MUST ignore a Membership Query message, or the encapsulated IP
datagram within it, if the message fails to satisfy any of the
following requirements:
Bumgardner Expires December 14, 2012 [Page 56]
Internet-Draft AMT June 2012
o The gateway MUST be waiting for a Membership Query message.
o The Request Nonce value contained in the Membership Query MUST
equal the Request Nonce value contained in the Request message.
o The source IP address and UDP port of the Membership Query MUST
equal the destination IP address and UDP port of the matching
Request message (i.e., the current relay address).
o The encapsulated IP datagram MUST carry an IGMPv3 or MLDv2
message. The protocol MUST match the protocol identified by the
"P" flag in the Request message.
o The IGMPv3 or MLDv2 message MUST be a general query message.
o The total length of the encapsulated IP datagram as computed from
the lengths contained in the datagram header(s) MUST NOT exceed
the available field length within the Membership Query message.
Once a gateway receives a Membership Query response to a Request
message, it SHOULD ignore any other Membership Query messages that
arrive on the AMT interface until it sends a new Request message.
The gateway MUST save the Membership Query message, or the Request
Nonce, Response MAC, Gateway IP Address and Gateway Port Number
fields for use in sending subsequent Membership Update and Teardown
messages.
The gateway extracts the encapsulated IP datagram and forwards it to
the local IP protocol implementation for checksum verification and
dispatching to the IGMP or MLD implementation running on the pseudo-
interface. The gateway MUST NOT forward any octets that might exist
between the encapsulated IP datagram and the end of the message or
Gateway Address fields.
The MLD protocol specification indicates that senders should use a
link-local source IP address in message datagrams. This requirement
must be relaxed for AMT because gateways and relays do not normally
share a common subnet. For this reason, a gateway implementation
MUST accept MLD (and IGMP) query message datagrams regardless of the
source IP address they carry. This may require additional processing
on the part of the gateway that might be avoided if the relay and
gateway use the IPv4 and IPv6 addresses allocated for use in AMT
encapsulated control packets as described in Section 5.2.1.
The gateway MUST start a timer that will trigger the next iteration
of the membership update cycle by executing the membership query
procedure. The gateway SHOULD compute the timer duration from the
Bumgardner Expires December 14, 2012 [Page 57]
Internet-Draft AMT June 2012
Querier's Query Interval Code carried by the general-query. A
gateway MAY use a smaller timer duration if required to refresh a NAT
mapping that would otherwise timeout. A gateway MAY use a larger
timer duration if it has no group subscriptions to report.
If the gateway supports the Teardown message and the G-flag is set in
the Membership Query message, the gateway MUST compare the Gateway IP
Address and Gateway Port Number on the new Membership Query message
with the values carried by the previous Membership Query message. If
either value has changed the gateway MUST send a Teardown message to
the relay as described in Section 5.2.3.7.
If the L-flag is set in the Membership Query message, the relay is
reporting that it is NOT accepting Membership Update messages that
create new tunnel endpoints and will simply ignore any that do. If
the L-flag is set and the gateway is not currently reporting any
group subscriptions to the relay, the gateway SHOULD stop sending
periodic Request messages and restart the relay discovery procedure
(if discovery is enabled) to find a new relay with which to
communicate. The gateway MAY continue to send updates even if the
L-flag is set, if it has previously reported group subscriptions to
the relay, one or more subscriptions still exist and the gateway
endpoint address has not changed since the last Membership Query was
received (see previous paragraph).
5.2.3.5.5. Handling Query Timer Expiration
When the query timer (started in the previous step) expires, the
gateway should execute the membership query procedure again to
continue the membership update cycle.
5.2.3.5.6. Request Nonce Generation
The request nonce MUST be a random value, and if possible, SHOULD be
computed using a cryptographically secure pseudo random number
generator. A new nonce MUST be generated each time the gateway
starts the membership query process. The same nonce SHOULD be used
when retransmitting a Request message.
5.2.3.6. Membership Update Procedure
This section describes gateway requirements related to the membership
update message sequence described in Section 4.2.1.2.
The membership update process is primarily driven by the host-mode
IGMP or MLD protocol implementation running on the gateway pseudo-
interface. The IGMP and MLD protocols produce current-state reports
in response to general queries generated by the pseudo-interface via
Bumgardner Expires December 14, 2012 [Page 58]
Internet-Draft AMT June 2012
AMT and produce state-change reports in response to receiver requests
made using the IGMP or MLD service interface.
5.2.3.6.1. Handling an IGMP/MLD IP Datagram
The gateway pseudo-interface MUST accept the following IP datagrams
from the IPv4/IGMP and IPv6/MLD protocols running on the pseudo-
interface:
o IPv4 datagrams that carry an IGMPv2, or IGMPv3 Membership Report
or an IGMPv2 Leave Group message as described in Section 4 of
[RFC3376].
o IPv6 datagrams that carry an MLDv1 or MLDv2 Multicast Listener
Report or an MLDv1 Multicast Listener Done message as described in
Section 5 of [RFC3810].
The gateway must be prepared to receive these messages any time the
pseudo-interface is running. The gateway MUST ignore any datagrams
not listed above.
A gateway that waits to start a membership update cycle until after
it receives a datagram containing an IGMP/MLD state-change message
MAY:
o Discard IGMP or MLD datagrams until it receives a Membership Query
message, at which time it processes the Membership Query message
as normal to eventually produce a current-state report on the
pseudo-interface which describes the end state (RECOMMENDED).
o Insert IGMP or MLD datagrams into a queue for transmission after
it receives a Membership Query message.
If and when a gateway receives a Membership Query message (for IGMP
or MLD) it sends any queued or incoming IGMP or MLD datagrams to the
relay as described in the next section.
5.2.3.6.2. Sending a Membership Update Message
A gateway cannot send a Membership Update message to a relay until it
has received a Membership Query message from a relay. If the gateway
has not yet located a relay with which to communicate, it MUST first
execute the relay discovery procedure described in Section 5.2.3.4 to
obtain a relay address. If the gateway has a relay address, but has
not yet received a Membership Query message, it MUST first execute
the membership query procedure described in Section 5.2.3.5 to obtain
a Request Nonce and Response MAC that can be used to send a
Membership Update message.
Bumgardner Expires December 14, 2012 [Page 59]
Internet-Draft AMT June 2012
Once a gateway possesses a valid Relay Address, Request Nonce and
Response MAC, it may encapsulate the IP datagram containing the IGMP/
MLD message into a Membership Update message. The gateway MUST copy
the Request Nonce and Response MAC values from the last Membership
Query received from the relay into the corresponding fields in the
Membership Update. The gateway MUST send the Membership Update
message using the Relay Address and IANA-assigned AMT port number as
the destination.
When a gateway sends a Membership Update message, it may be notified
that an ICMP Destination Unreachable message was received as a result
of an earlier AMT message transmission. Handling of ICMP Destination
Unreachable messages is described in Section 5.2.3.9.
5.2.3.7. Teardown Procedure
This section describes gateway requirements related to the teardown
message sequence described in Section 4.2.1.3.
Gateway support for the Teardown message is OPTIONAL but RECOMMENDED.
A gateway that supports Teardown SHOULD make use of Teardown
functionality if it receives a Membership Query message from a relay
that has the "G" flag set to indicate that it contains valid gateway
address fields.
5.2.3.7.1. Handling a Membership Query Message
As described in Section 5.2.3.5.4, if a gateway supports the Teardown
message, has reported active group subscriptions, and receives a
Membership Query message with the "G" flag set, the gateway MUST
compare the Gateway IP Address and Gateway Port Number on the new
Membership Query message with the values carried by the previous
Membership Query message. If either value has changed the gateway
MUST send a Teardown message as described in the next section.
5.2.3.7.2. Sending a Teardown Message
A gateway sends a Teardown message to a relay to request that it stop
delivering Multicast Data messages to the gateway and delete any
group memberships created by the gateway.
When a gateway constructs a Teardown message, it MUST copy the
Request Nonce, Response MAC, Gateway IP Address and Gateway Port
Number fields from the Membership Query message that provided the
Response MAC for the last Membership Update message sent, into the
corresponding fields of the Teardown message.
Bumgardner Expires December 14, 2012 [Page 60]
Internet-Draft AMT June 2012
A gateway MUST send the Teardown message using the Relay Address and
IANA-assigned AMT port number as the destination. A gateway MAY send
the Teardown message multiple times for robustness. The gateway
SHOULD use the Querier's Robustness Variable (QRV) field contained in
the query encapsulated within the last Membership Query to set the
limit on the number of retransmissions. If the gateway sends the
Teardown message multiple times, it SHOULD insert a delay between
each transmission using the timing algorithm employed in IGMP/MLD for
transmitting unsolicited state-change reports. The RECOMMENDED
default delay value is 1 second.
When a gateway sends a Teardown message, it may be notified that an
ICMP Destination Unreachable message was received as a result of an
earlier AMT message transmission. Handling of ICMP Destination
Unreachable messages is described in Section 5.2.3.9.
5.2.3.8. Shutdown
When a gateway pseudo-interface is stopped and the gateway has
existing group subscriptions, the gateway SHOULD either:
o Send a Teardown message to the relay as described in
Section 5.2.3.7, but only if the gateway supports the Teardown
message, and the current relay is returning gateway address fields
in Membership Query messages, or
o Send a Membership Update message to the relay that will delete
existing group subscriptions.
5.2.3.9. Handling ICMP Destination Unreachable Responses
A gateway may receive an ICMP "Destination Unreachable" message
[RFC0792] after sending an AMT message. Whether the gateway is
notified that an ICMP message was received is highly dependent the
gateway IP stack behavior and gateway implementation.
If the reception of an ICMP Destination Unreachable message is
reported to the gateway while waiting to receive an AMT message, the
gateway may respond as follows, depending on platform capabilities
and which outgoing message triggered the ICMP response:
1. The gateway MAY simply abandon the current relay and restart
relay discovery (if used). This is the least desirable approach
as it does not allow for transient network changes.
2. If the last message sent was a Relay Discovery or Request
message, the gateway MAY simply ignore the ICMP response and
continue waiting for incoming AMT messages. If the gateway is
Bumgardner Expires December 14, 2012 [Page 61]
Internet-Draft AMT June 2012
configured to retransmit Relay Discovery or Request messages, the
normal retransmission behavior for those messages is preserved to
prevent the gateway from prematurely abandoning a relay.
3. If the last message sent was a Membership Update message, the
gateway MAY start a new membership update and associated Request
retransmission cycle.
If the reception of an ICMP Destination Unreachable message is
reported to the gateway when attempting to transmit a new AMT
message, the gateway may respond as follows, depending on platform
capabilities and which outgoing message triggered the ICMP response:
1. The gateway MAY simply abandon the current relay and restart
relay discovery (if used). This is the least desirable approach
as it does not allow for transient network changes.
2. If the last message sent was a Relay Discovery, Request or
Teardown message, the gateway MAY attempt to transmit the new
message. If the gateway is configured to retransmit Relay
Discovery, Request or Teardown messages, the normal
retransmission behavior for those messages is preserved to
prevent the gateway from prematurely abandoning a relay.
3. If the last message sent was a Membership Update message, the
gateway SHOULD start a new membership update and associated
Request retransmission cycle.
5.3. Relay Operation
The following sections describe relay implementation requirements. A
non-normative discussion of relay operation may be found in
Section 4.2.
5.3.1. IP/IGMP/MLD Protocol Requirements
A relay requires a subset of router-mode IGMP and MLD functionality
to provide group membership tracking and report processing.
A relay accessible via IPv4 MUST support IPv4/IGMPv3 and MAY support
IPv6/MLDv2. A relay accessible via IPv6 MUST support IPv6/MLDv2 and
MAY support IPv4/IGMPv3.
A relay MUST apply the forwarding rules described in Section 6.3 of
[RFC3376] and Section 7.3 of [RFC3810].
A relay MUST handle incoming reports as described in Section 6.4 of
[RFC3376] and Section 7.4 of [RFC3810] with the exception that
Bumgardner Expires December 14, 2012 [Page 62]
Internet-Draft AMT June 2012
actions that lead to queries MAY be modified to eliminate query
generation. A relay MUST accept IGMP and MLD report datagrams
regardless of the IP source address carried by those datagrams.
All other aspects of IGMP/MLD router behavior, such as the handling
of queries, querier election, etc., are not used or required for
relay operation.
5.3.2. Startup
If a relay is deployed for anycast discovery, the relay MUST
advertise an anycast Relay Discovery Address Prefix into the unicast
routing system of the anycast domain. An address within that prefix,
i.e., a Relay Discovery Address, MUST be assigned to a relay
interface.
A unicast IPv4 and/or IPv6 address MUST be assigned to the relay
interface that will be used to send and receive AMT control and data
messages. This address or addresses are returned in Relay
Advertisement messages.
The remaining details of relay "startup" are highly implementation-
dependent and are not addressed in this document.
5.3.3. Running
When a relay is started, it begins listening for AMT messages on the
interface to which the unicast Relay Address(es) has been assigned,
i.e., the address returned in Relay Advertisement messages.
5.3.3.1. Handling AMT Messages
A relay MUST ignore any message other than a Relay Discovery,
Request, Membership Update or Teardown message. The handling of
Relay Discovery, Request, Membership Update, and Teardown messages is
addressed in the sections that follow.
Support for the Teardown message is OPTIONAL. If a relay does not
support the Teardown message, it MUST also ignore this message.
A relay that conforms to this specification MUST ignore any message
with a Version field value other than zero.
5.3.3.2. Handling a Relay Discovery Message
This section describes relay requirements related to the relay
discovery message sequence described in Section 4.2.1.1.
Bumgardner Expires December 14, 2012 [Page 63]
Internet-Draft AMT June 2012
A relay MUST accept and respond to Relay Discovery messages sent to
an anycast relay discovery address or the unicast relay address. If
a relay receives a Relay Discovery message sent to its unicast
address, it MUST respond just as it would if the message had been
sent to its anycast discovery address.
When a relay receives a Relay Discovery message it responds by
sending a Relay Advertisement message back to the source of the Relay
Discovery message. The relay MUST use the source IP address and UDP
port of the Relay Discovery message as the destination IP address and
UDP port. The relay MUST use the destination IP address and UDP port
of the Relay Discovery as the source IP address and UDP port to
ensure successful NAT traversal.
The relay MUST copy the value contained in the Discovery Nonce field
of the Relay Discovery message into the Discovery Nonce field in the
Relay Advertisement message.
If the Relay Discovery message was received as an IPv4 datagram, the
relay MUST return an IPv4 address in the Relay Address field of the
Relay Advertisement message. If the Relay Discovery message was
received as an IPv6 datagram, the relay MUST return an IPv6 address
in the Relay Address field.
5.3.3.3. Handling a Request Message
This section describes relay requirements related to the membership
query portion of the message sequence described in Section 4.2.1.2.
When a relay receives a Request message it responds by sending a
Membership Query message back to the source of the Request message.
The relay MUST use the source IP address and UDP port of the Request
message as the destination IP address and UDP port for the Membership
Query message. The source IP address and UDP port carried by the
Membership Query MUST match the destination IP address and UDP port
of the Request to ensure successful NAT traversal.
The relay MUST return the value contained in the Request Nonce field
of the Request message in the Request Nonce field of the Membership
Query message. The relay MUST compute a MAC value, as described in
Section 5.3.5, and return that value in the Response MAC field of the
Membership Query message.
If a relay supports the Teardown message, it MUST set the G-flag in
the Membership Query message and return the source IP address and UDP
port carried by the Request message in the corresponding Gateway IP
Address and Gateway Port Number fields. If the relay does not
Bumgardner Expires December 14, 2012 [Page 64]
Internet-Draft AMT June 2012
support the Teardown message it SHOULD NOT set these fields as this
may cause the gateway to generate unnecessary Teardown messages.
If the P-flag in the Request message is 0, the relay MUST return an
IPv4-encapsulated IGMPv3 general query in the Membership Query
message. If the P-flag is 1, the relay MUST return an IPv6-
encapsulated MLDv2 general query in the Membership Query message.
If the relay is not accepting Membership Update messages that create
new tunnel endpoints due to resource limitations, it SHOULD set the
L-flag in the Membership Query message to notify the gateway of this
state. Support for the L-flag is OPTIONAL. See Section 5.3.3.8.
The IGMPv3 general query datagram that a relay encapsulates within a
Membership Query message MUST conform to the descriptions found in
Section 4.1 of [RFC3376]. These datagrams MUST possess the IP
headers, header options and header values called for in [RFC3376],
with the following exception; the source IP address for an IGMP
general query datagram MAY be set to the "unspecified" address (all
octets are zero) but SHOULD be set to an address in the address range
specifically assigned by IANA for use in the IGMP messages sent from
a relay to a gateway (i.e. 154.7.1.1 as described in Section 7).
This exception is made because the source address that a relay might
normally send may not be a valid source address on any gateway
interface. The rationale for using the aforementioned source
addresses is primary one of convenience - a gateway will accept an
IGMP query regardless of the source address it carries. See
Section 5.2.1.
The MLDv2 general query datagram that a relay encapsulates within a
Membership Query message MUST conform to the descriptions found in
Section 5.1 of [RFC3810]. These datagrams MUST possess the IP
headers, header options and header values called for in [RFC3810],
with the following exception; the source IP address for an MLD
general query datagram MAY be set to the "unspecified" address (all
octets are zero) but SHOULD be set to an IPv6 link-local address in
the range FE80::/64. A relay may use a dynamically-generated link-
local address or the fixed address FE80::2. As with IGMP, a gateway
will accept an MLD query regardless of the source address it carries.
See Section 5.2.1.
A relay MUST set the Querier's Query Interval Code (QQIC) field in
the general query to supply the gateway with a suggested time
duration to use for the membership query timer. The QQIC field is
defined in Section 4.1.1 in [RFC3376] and Section 5.1.3 in [RFC3810].
A relay MAY adjust this value to affect the rate at which the Request
messages are sent from a gateway. However, a gateway is allowed to
use a shorter duration than specified in the QQIC field, so a relay
Bumgardner Expires December 14, 2012 [Page 65]
Internet-Draft AMT June 2012
may be limited in its ability to spread out Requests coming from a
gateway.
A relay MUST set the Querier's Robustness Variable (QRV) field in the
general query to a non-zero value. This value SHOULD be greater than
one. If a gateway retransmits membership state change messages, it
will retransmit them (robustness variable - 1) times.
A relay SHOULD set the Max Resp Code field in the general query to a
value of 1 to trigger an immediate response from the gateway (some
host IGMP/MLD implementations may not accept a value of zero). A
relay SHOULD NOT use the IGMPv2/MLDv2 Query Response Interval
variable, if available, to generate the Max Resp Code field value as
the Query Response Interval variable is used in setting the duration
of group state timers and must not be set to such a small value. See
Section 5.3.3.7.
5.3.3.4. Handling a Membership Update Message
This section describes relay requirements related to the membership
update portion of the message sequence described in Section 4.2.1.2.
When a relay receives a Membership Update message it must first
determine whether it should accept or ignore the message. A relay
MUST NOT make any changes to group membership and forwarding state if
the message fails to satisfy any of the following requirements:
o The IP datagram encapsulated within the message MUST be one of the
following:
* IPv4 datagram carrying an IGMPv2 or IGMPv3 Membership Report
message.
* IPv4 datagram carrying an IGMPv2 Leave Group message.
* IPv6 datagram carrying an MLDv1 or MLDv2 Multicast Listener
Report message.
* IPv6 datagram carrying MLDv1 Multicast Listener Done message.
o The encapsulated IP datagram MUST satisfy the IP header
requirements for the IGMP or MLD message type as described in
Section 4 of [RFC3376], Section 2 of [RFC2236], Section 5 of
[RFC3810], and Section 3 of [RFC2710], with the following
exception - a relay MUST accept an IGMP or MLD message regardless
of the IP source address carried by the datagram.
Bumgardner Expires December 14, 2012 [Page 66]
Internet-Draft AMT June 2012
o The total length of the encapsulated IP datagram as computed from
the lengths contained in the datagram header(s) MUST NOT exceed
the available field length within the Membership Update message.
o The computed checksums for the encapsulated IP datagram and its
payload MUST match the values contained therein. Checksum
computation and verification varies by protocol; See [RFC0791] for
IPv4, [RFC3376] for IGMPv3, and [RFC4443] for MLD (ICMPv6).
o If processing of the encapsulated IGMP or MLD message would result
in an allocation of new state or a modification of existing state,
the relay MUST authenticate the source of the Membership message
by verifying that the value contained in the Response MAC field
equals the MAC value computed from the fields in the Membership
Update message datagram. Because the private secret used to
compute Response MAC values may change over time, the relay MUST
retain the previous version of the private secret to use in
authenticating Membership Updates sent during the subsequent query
interval. If the first attempt at Response MAC authentication
fails, the relay MUST attempt to authenticate the Response MAC
using the previous private secret value unless 2*query_interval
time has elapsed since the private secret change. See
Section 5.3.5. An alternative approach to Response MAC generation
that avoids repeated Response MAC computations may be found in
Appendix A.1.
A relay MAY skip source authentication to reduce the computational
cost of handling Membership Update messages if the relay can make a
trivial determination that the IGMP/MLD message carried by the
Membership Update message will produce no changes in group membership
or forwarding state. The relay does not need to compute and compare
MAC values if it finds there are no group subscriptions for the
source of the Membership Update message and either of the following
is true:
o The encapsulated IP datagram is an IGMPv3 Membership Report or
MLDv2 Multicast Listener Report message that contains no group
records. This may often be the case for gateways that
continuously repeat the membership update cycle even though they
have no group subscriptions to report.
o The encapsulated IP datagram is an IGMPv2 Leave Group or MLDv1
Multicast Listener Done message.
The IGMP and MLD protocol specifications indicate that senders SHOULD
use a link-local source IP address in message datagrams. This
requirement must be relaxed for AMT because gateways and relays do
not share a common subnet. For this reason, a relay implementation
Bumgardner Expires December 14, 2012 [Page 67]
Internet-Draft AMT June 2012
MUST accept IGMP and MLD datagrams regardless of the source IP
address they carry.
Once a relay has determined that the Membership Update message is
valid, it processes the encapsulated IGMP or MLD membership message
to update group membership state and communicates with the multicast
protocol to update forwarding state and possibly send multicast
protocol messages towards upstream routers. The relay MUST ignore
any octets that might exist between the encapsulated IP datagram and
the end of the Membership Update message.
As described in Section 4.2.2, a relay uses the source IP address and
source UDP port carried by a Membership Update messages to identify a
tunnel endpoint. A relay uses the tunnel endpoint as the destination
address for any Multicast Data messages it sends as a result of the
group membership and forwarding state created by processing the IGMP/
MLD messages contained in Membership Update messages received from
the endpoint.
If a Membership Update message originates from a new endpoint, the
relay MUST determine whether it can accept updates from a new
endpoint. If a relay has been configured with a limit on the total
number of endpoints, or a limit on the total number of endpoints for
a given source address, then the relay MAY ignore the Membership
Update message and possibly withdraw any Relay Discovery Address
Prefix announcement that it might have made. See Section 5.3.3.8.
A relay MUST maintain some form of group membership database for each
endpoint. The per-endpoint databases are used update a forwarding
table containing entries that map an (*,G) or (S,G) subscription to a
list of tunnel endpoints.
A relay MUST maintain some form of group membership database
representing a merger of the group membership databases of all
endpoints. The merged group membership database is used to update
upstream multicast forwarding state.
A relay MUST maintain a forwarding table that maps each unique (*,G)
and (S,G) subscription to a list of tunnel endpoints. A relay uses
this forwarding table to provide the destination address when
performing UDP/IP encapsulation of the incoming multicast IP
datagrams to form Multicast Data messages.
If a group filter mode for a group entry on a tunnel endpoint is
EXCLUDE, the relay SHOULD NOT forward datagrams that originate from
sources in the filter source list unless the relay architecture does
not readily support source filtering. A relay MAY ignore the source
list if necessary because gateways are expected to do their own
Bumgardner Expires December 14, 2012 [Page 68]
Internet-Draft AMT June 2012
source filtering.
5.3.3.5. Handling a Teardown Message
This section describes relay requirements related to the teardown
message sequence described in Section 4.2.1.3.
When a relay (that supports the Teardown message) receives a Teardown
message, it MUST first authenticate the source of the Teardown
message by verifying that the Response MAC carried by the Teardown
message is equal to a MAC value computed from the fields carried by
the Teardown message. The method used to compute the MAC differs
from that used to generate and validate the Membership Query and
Membership Update messages in that the source IP address and source
UDP port number used to compute the MAC are taken from the Gateway IP
Address and Gateway Port Number field in the Teardown message rather
than from the IP and UDP headers in the datagram that carries the
Teardown message. The MAC computation is described Section 5.3.5. A
relay MUST ignore a Teardown message If the computed MAC does not
equal the value of the Response MAC field.
If a relay determines that a Teardown message is authentic, it MUST
immediately stop transmitting Multicast Data messages to the endpoint
identified by the Gateway IP Address and Gateway Port Number fields
in the message. The relay MUST eventually delete any group
membership and forwarding state associated with the endpoint, but MAY
delay doing so to allow a gateway to recreate group membership state
on a new endpoint and thereby avoid making unnecessary (temporary)
changes in upstream routing/forwarding state.
The state changes made by a relay when processing a Teardown message
MUST be identical to those that would be made as if the relay had
received an IGMP/MLD report that would cause the IGMP or MLD protocol
to delete all existing group records in the group membership database
associated with the endpoint. The processing of the Teardown message
should trigger or mimic the normal interaction between IGMP or MLD
and a multicast protocol to produce required changes in forwarding
state and possibly send prune/leave messages towards upstream
routers.
5.3.3.6. Handling Multicast IP Datagrams
When a multicast IP datagram is forwarded to the relay pseudo-
interface, the relay MUST, for each gateway that has expressed an
interest in receiving the datagram, encapsulate the IP datagram into
a Multicast Data message and send that message to the gateway. This
process is highly implementation dependent, but conceptually requires
the following steps:
Bumgardner Expires December 14, 2012 [Page 69]
Internet-Draft AMT June 2012
o Use the IP datagram source and destination address to look up the
appropriate (*,G) or (S,G) entry in the endpoint forwarding table
created for the pseudo-interface as a result of IGMP/MLD
processing.
o Possibly replicate the datagram for each gateway endpoint listed
for that (*,G) or (S,G) entry.
o Encapsulate the IP datagram in a UDP/IP Membership Data message,
using the endpoint UDP/IP address as the destination address and
the unicast relay address and IANA-assigned port as the source
UDP/IP address. To ensure successful NAT traversal, the source
address and port MUST match the destination address and port
carried by the Membership Update message sent by the gateway to
create the forwarding table entry.
o If possible, the relay SHOULD compute a valid, non-zero checksum
for the UDP datagram carrying the Membership Data message. See
Section 4.2.2.3.
o Send the message to the gateway.
The relay pseudo-interface MUST ignore any other IP datagrams
forwarded to the pseudo-interface.
5.3.3.7. State Timers
A relay MUST maintain a timer or timers whose expiration will trigger
the removal of any group subscriptions and forwarding state
previously created for a gateway endpoint should the gateway fail to
refresh the group membership state within a specified time interval.
A relay MAY use a variant of the IGMPv3/MLDv2 state management
protocol described in Section 6 of [RFC3376] or Section 7 of
[RFC3810], or may maintain a per-endpoint timer to trigger the
deletion of group membership state.
If a per-endpoint timer is used, the relay MUST restart this timer
each time it receives a new Membership Update message from the
gateway endpoint.
The endpoint timer duration MAY be computed from tunable IGMP/MLD
variables as follows:
((Robustness_Variable) * (Query_Interval)) + Query_Response_Interval
If IGMP/MLD default values are used for these variables, the gateway
will timeout after 125s * 2 + 10s = 260s. The timer duration MUST be
Bumgardner Expires December 14, 2012 [Page 70]
Internet-Draft AMT June 2012
greater than the query interval suggested in the last Membership
Query message sent to the gateway endpoint.
Regardless of the timers used (IGMPv3/MLDv2 or endpoint), the
Query_Response_Interval value SHOULD be greater than or equal to 10s
to allow for packet loss and round-trip time in the Request/
Membership Query message exchange.
5.3.3.8. Relay Resource Management
A relay may be configured with various service limits to ensure a
minimum level of performance for gateways that connect to it.
If a relay has determined that it has reached or exceeded maximum
allowable capacity or has otherwise exhausted resources required to
support additional gateways, it SHOULD withdraw any Relay Discovery
Address Prefix it has advertised into the unicast internetwork and
SHOULD set the L-flag in any Membership Query messages it returns to
gateways while in this state.
If the relay receives an update from a gateway that adds group
membership or forwarding state for an endpoint that has already
reached maximum allowable state entries, the relay SHOULD continue to
accept updates from the gateway but ignore any group membership/
forwarding state additions requested by that gateway.
If the relay receives an update from a gateway that would create a
new tunnel endpoint for a source IP address that has already reached
the maximum allowable number of endpoints (maximum UDP ports), it
should simply ignore the Membership Update.
5.3.4. Shutdown
The following steps should be treated as an abstract description of
the shutdown procedure for a relay:
o Withdraw the Relay Discovery Address Prefix advertisement (if
used).
o Stop listening for Relay Discovery messages.
o Stop listening for control messages from gateways.
o Stop sending data messages to gateways.
o Delete all AMT group membership and forwarding state created on
the relay, coordinating with the multicast routing protocol to
update the group membership state on upstream interfaces as
Bumgardner Expires December 14, 2012 [Page 71]
Internet-Draft AMT June 2012
required.
5.3.5. Response MAC Generation
A Response MAC is produced by a hash digest computation. A Response
MAC value is computed from a Request message for inclusion in a
Membership Query message, is computed from a Membership Update
message to authenticate the Response MAC carried within that message,
and is computed from fields in a Teardown message to authenticate the
Response MAC carried within that message.
Gateways treat the Response MAC field as an opaque value, so a relay
implementation may generate the MAC using any method available to it.
The hash function RECOMMENDED for use in computing the Response MAC
is the MD5 hash digest [RFC1321], though hash functions or keyed-hash
functions of greater cryptographic strength may be used.
The digest MUST be computed over the following values:
o The Source IP address of the message (or Teardown Gateway IP
Address field)
o The Source UDP port of the message (or Teardown Gateway Port
Number field)
o The Request Nonce contained in the message.
o A private secret known only to the relay
An Response MAC generation solution that satisfies these requirements
is described in Appendix A.1.
5.3.6. Private Secret Generation
The private secret, or hash-key, is a random value that the relay
includes in the Response MAC hash digest computation. A relay SHOULD
periodically compute a new private secret. The RECOMMENDED maximum
interval is 2 hours. A relay MUST retain the prior secret for use in
verifying MAC values that were sent to gateways just prior to the use
of the new secret.
The private secret SHOULD be computed using a cryptographically-
secure pseudo-random number generator. The private secret width
SHOULD equal that of the hash function used to compute the Response
MAC, e.g., 128-bits for an MD5 hash.
Bumgardner Expires December 14, 2012 [Page 72]
Internet-Draft AMT June 2012
6. Security Considerations
AMT is not intended to be a strongly secured protocol. In general,
the protocol provides the same level of security and robustness as is
provided by the UDP, IGMP and MLD protocols on which it relies. The
lack of strong security features can largely be attributed to the
desire to make the protocol light-weight by minimizing the state and
computation required to service a single gateway, thereby allowing a
relay to service a larger number of gateways.
Many of the threats and vectors described in [RFC3552] may be
employed against the protocol to launch various types of denial-of-
service attacks that can affect the functioning of gateways or their
ability to locate and communicate with a relay. These scenarios are
described below.
As is the case for UDP, IGMP and MLD, the AMT protocol provides no
mechanisms for ensuring message delivery or integrity. The protocol
does not provide confidentiality - multicast groups, sources and
streams requested by a gateway are sent in the clear.
The protocol does use a three-way handshake to provide trivial source
authentication for state allocation and updates (see below). The
protocol also requires gateways and relays to ignore malformed
messages and those messages that do not carry expected address values
or protocol payload types or content.
6.1. Relays
The three-way handshake provided by the membership update message
sequence (See (Section 4.2.1.2)) provides a defense against source-
spoofing-based resource-exhaustion attacks on a relay by requiring
source authentication before state allocation. However, attackers
may still attempt to flood a relay with Request and Membership Update
messages to force the relay to make the hash computations in an
effort to consume computational resources. Implementations may
choose to limit the frequency with which a relay responds to Request
messages sent from a single IP address or IP address and UDP port
pair, but support for this functionality is not required. The three-
way handshake provides no defense against an eavesdropping or man-in-
the-middle attacker.
Attackers that execute the gateway protocol may consume relay
resources by instantiating a large number of tunnels or joining a
large number of multicast streams. A relay implementation should
provide a mechanism for limiting the number of tunnels (Multicast
Data message destinations) that can be created for a single gateway
source address. Relays should also provide a means for limiting the
Bumgardner Expires December 14, 2012 [Page 73]
Internet-Draft AMT June 2012
number of joins per tunnel instance as a defense against these
attacks.
Relays may withdraw their AMT anycast prefix advertisement when they
reach configured maximum capacity or exhaust required resources.
This behavior allows gateways to use the relay discovery process to
find the next topologically-nearest relay that has advertised the
prefix. This behavior also allows a successful resource exhaustion
attack to propagate from one relay to the next until all relays
reachable using the anycast address have effectively been taken
offline. This behavior may also be used to acquire the unicast
addresses for individual relays which can then be used to launch a
DDoS attack on all of the relays without using the relay discovery
process. To prevent wider disruption of AMT-based distribution
network, relay anycast address advertisements can be limited to
specific administrative routing domains. This will isolate such
attacks to a single domain.
6.2. Gateways
A passive eavesdropper may launch a denial-of-service attack on a
gateway by capturing a Membership Query or Membership Update message
and using the request nonce and message authentication code carried
by the captured message to send a spoofed a Membership Update or
Teardown message to the relay. The spoofed messages may be used to
modify or destroy group membership state associated with the gateway,
thereby changing or interrupting the multicast traffic flows.
A passive eavesdropper may also spoof Multicast Data messages in an
attempt to overload the gateway or disrupt or supplant existing
traffic flows. A properly implemented gateway will filter Multicast
Data messages that do not originate from the expected relay address
and should filter non-multicast packets and multicast IP packets
whose group or source addresses are not included in the current
reception state for the gateway pseudo-interface.
An active eavesdropper may launch a man-in-the-middle attack in which
messages normally exchanged between a gateway and relay are
intercepted, modified, spoofed or discarded by the attacker. The
attacker may deny access to, modify or replace requested multicast
traffic. The AMT protocol provides no means for detecting or
defending against a man-in-the-middle attack - any such functionality
must be provided by multicast receiver applications through
independent detection and validation of incoming multicast datagrams.
The anycast discovery technique for finding relays (see
Section 4.1.4) introduces a risk that a rogue router or a rogue AS
could introduce a bogus route to a specific Relay Discovery Address
Bumgardner Expires December 14, 2012 [Page 74]
Internet-Draft AMT June 2012
prefix, and thus divert or absorb Relay Discovery messages sent by
gateways. Network managers must guarantee the integrity of their
routing to a particular Relay Discovery Address prefix in much the
same way that they guarantee the integrity of all other routes.
6.3. Encapsulated IP Packets
An attacker forging or modifying a Membership Query or Membership
Update message may attempt to embed something other than an IGMP or
MLD message within the encapsulated IP packet carried by these
messages in an effort to introduce these into the recipient's IP
stack. A properly implemented gateway or relay will ignore any such
messages - and may further choose to ignore Membership Query messages
that do not contain a IGMP/MLD general queries or Membership Update
messages that do not contain IGMP/MLD membership reports.
Properly implemented gateways and relays will also filter
encapsulated IP packets that appear corrupted or truncated by
verifying packet length and checksums.
Bumgardner Expires December 14, 2012 [Page 75]
Internet-Draft AMT June 2012
7. IANA Considerations
7.1. IPv4 and IPv6 Anycast Prefix Allocation
IANA should allocate an IPv4 prefix and an IPv6 prefix dedicated to
the public AMT Relays to advertise to the native multicast backbone
(as described in Section 4.1.4). The prefix length should be
determined by the IANA; the prefix should be large enough to
guarantee advertisement in the default-free BGP networks.
7.1.1. IPv4
A prefix length of 24 will meet this requirement.
Internet Systems Consortium (ISC) has offered 154.7.0/24 for this
purpose.
7.1.2. IPv6
A prefix length of 32 will meet this requirement. IANA has
previously set aside the range 2001::/16 for allocating prefixes for
this purpose.
7.2. IPv4 Address Prefix Allocation for IGMP Source Addresses
IANA should allocate an IPv4 prefix dedicated for use in IGMP
messages exchanged between gateways and relays. This address range
is intended for use within tunnels constructed between a gateway and
relay, and as such, is not intended to be globally routable.
A prefix length of 24 will meet this requirement.
Internet Systems Consortium (ISC) has offered 154.7.1/24 for this
purpose.
7.3. UDP Port number
IANA has reserved UDP port number 2268 for AMT.
Bumgardner Expires December 14, 2012 [Page 76]
Internet-Draft AMT June 2012
8. Contributors
The following people provided significant contributions to the design
of the protocol and earlier versions of this specification:
Thomas Morin
France Telecom - Orange
2, avenue Pierre Marzin
Lannion 22300
France
Email: thomas.morin@orange.com
Dirk Ooms
OneSparrow
Belegstraat 13; 2018 Antwerp;
Belgium
EMail: dirk@onesparrow.com
Tom Pusateri
!j
2109 Mountain High Rd.
Wake Forest, NC 27587
USA
Email: pusateri@bangj.com
Dave Thaler
Microsoft Corporation
One Microsoft Way
Redmond, WA 98052-6399
USA
Email: dthaler@microsoft.com
Bumgardner Expires December 14, 2012 [Page 77]
Internet-Draft AMT June 2012
9. Acknowledgments
The authors would like to thank the following individuals for their
suggestions, comments, and corrections:
Amit Aggarwal
Mark Altom
Toerless Eckert
Marshall Eubanks
Gorry Fairhurst
Dino Farinacci
Lenny Giuliano
Andy Huang
Tom Imburgia
Patricia McCrink
Han Nguyen
Doug Nortz
Pekka Savola
Robert Sayko
Greg Shepherd
Steve Simlo
Mohit Talwar
Lorenzo Vicisano
Kurt Windisch
John Zwiebel
The anycast discovery mechanism described in this document is based
on similar work done by the NGTrans WG for obtaining automatic IPv6
connectivity without explicit tunnels ("6to4"). Tony Ballardie
provided helpful discussion that inspired this document.
Juniper Networks was instrumental in funding several versions of this
draft as well as an open source implementation.
Bumgardner Expires December 14, 2012 [Page 78]
Internet-Draft AMT June 2012
10. References
10.1. Normative References
[RFC0768] Postel, J., "User Datagram Protocol", STD 6, RFC 768,
August 1980.
[RFC0792] Postel, J., "Internet Control Message Protocol", STD 5,
RFC 792, September 1981.
[RFC1321] Rivest, R., "The MD5 Message-Digest Algorithm", RFC 1321,
April 1992.
[RFC3376] Cain, B., Deering, S., Kouvelas, I., Fenner, B., and A.
Thyagarajan, "Internet Group Management Protocol, Version
3", RFC 3376, October 2002.
[RFC3810] Vida, R. and L. Costa, "Multicast Listener Discovery
Version 2 (MLDv2) for IPv6", RFC 3810, June 2004.
[RFC4291] Hinden, R. and S. Deering, "IP Version 6 Addressing
Architecture", RFC 4291, February 2006.
[RFC4605] Fenner, B., He, H., Haberman, B., and H. Sandick,
"Internet Group Management Protocol (IGMP) / Multicast
Listener Discovery (MLD)-Based Multicast Forwarding
("IGMP/MLD Proxying")", RFC 4605, August 2006.
[RFC4607] Holbrook, H. and B. Cain, "Source-Specific Multicast for
IP", RFC 4607, August 2006.
[RFC4787] Audet, F. and C. Jennings, "Network Address Translation
(NAT) Behavioral Requirements for Unicast UDP", BCP 127,
RFC 4787, January 2007.
10.2. Informative References
[I-D.ietf-6man-udpchecksums]
Eubanks, M. and P. Chimento, "UDP Checksums for Tunneled
Packets", draft-ietf-6man-udpchecksums-02 (work in
progress), March 2012.
[I-D.ietf-6man-udpzero]
Fairhurst, G. and M. Westerlund, "IPv6 UDP Checksum
Considerations", draft-ietf-6man-udpzero-05 (work in
progress), December 2011.
[RFC0791] Postel, J., "Internet Protocol", STD 5, RFC 791,
Bumgardner Expires December 14, 2012 [Page 79]
Internet-Draft AMT June 2012
September 1981.
[RFC1112] Deering, S., "Host extensions for IP multicasting", STD 5,
RFC 1112, August 1989.
[RFC1546] Partridge, C., Mendez, T., and W. Milliken, "Host
Anycasting Service", RFC 1546, November 1993.
[RFC2104] Krawczyk, H., Bellare, M., and R. Canetti, "HMAC: Keyed-
Hashing for Message Authentication", RFC 2104,
February 1997.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2236] Fenner, W., "Internet Group Management Protocol, Version
2", RFC 2236, November 1997.
[RFC2460] Deering, S. and R. Hinden, "Internet Protocol, Version 6
(IPv6) Specification", RFC 2460, December 1998.
[RFC2663] Srisuresh, P. and M. Holdrege, "IP Network Address
Translator (NAT) Terminology and Considerations",
RFC 2663, August 1999.
[RFC2710] Deering, S., Fenner, W., and B. Haberman, "Multicast
Listener Discovery (MLD) for IPv6", RFC 2710,
October 1999.
[RFC3053] Durand, A., Fasano, P., Guardini, I., and D. Lento, "IPv6
Tunnel Broker", RFC 3053, January 2001.
[RFC3056] Carpenter, B. and K. Moore, "Connection of IPv6 Domains
via IPv4 Clouds", RFC 3056, February 2001.
[RFC3068] Huitema, C., "An Anycast Prefix for 6to4 Relay Routers",
RFC 3068, June 2001.
[RFC3552] Rescorla, E. and B. Korver, "Guidelines for Writing RFC
Text on Security Considerations", BCP 72, RFC 3552,
July 2003.
[RFC3973] Adams, A., Nicholas, J., and W. Siadak, "Protocol
Independent Multicast - Dense Mode (PIM-DM): Protocol
Specification (Revised)", RFC 3973, January 2005.
[RFC4443] Conta, A., Deering, S., and M. Gupta, "Internet Control
Message Protocol (ICMPv6) for the Internet Protocol
Bumgardner Expires December 14, 2012 [Page 80]
Internet-Draft AMT June 2012
Version 6 (IPv6) Specification", RFC 4443, March 2006.
[RFC4601] Fenner, B., Handley, M., Holbrook, H., and I. Kouvelas,
"Protocol Independent Multicast - Sparse Mode (PIM-SM):
Protocol Specification (Revised)", RFC 4601, August 2006.
[RFC4760] Bates, T., Chandra, R., Katz, D., and Y. Rekhter,
"Multiprotocol Extensions for BGP-4", RFC 4760,
January 2007.
[RFC4786] Abley, J. and K. Lindqvist, "Operation of Anycast
Services", BCP 126, RFC 4786, December 2006.
Bumgardner Expires December 14, 2012 [Page 81]
Internet-Draft AMT June 2012
Appendix A. Implementation Notes
A.1. Response MAC Generation and Keying
This specification does not require relays to use any particular
method to compute the Response MAC field value - only that it contain
a hash of the source IP address, source UDP port, request nonce, and
a private secret known only to the relay. This allows the relay
implementor a significant amount of leeway in the computation and
structure of the value stored in the Response MAC field.
Section Section 5.3.6 states that a relay should periodically compute
a new private secret (or hash-key) for MAC generation. To prevent
the relay from rejecting Membership Update messages that contain
Response MAC values computed from an old secret, the relay is
required to retain the previous secret so that it can re-attempt
authentication using the old secret, should authentication fail after
recomputing the MAC using the new secret. However, this approach
requires a relay to do at least two hash computations for every
Membership Update message that carries an old or a invalid MAC. A
better approach would be to include information within the message
that the relay could use to choose a single secret for authentication
rather relying on sequential authentication failures to test all
possible secrets.
The solution proposed here is to compute and exchange an
"authentication cookie" rather than a simple hash value in the
Response MAC field. The authentication cookie would combine a
timestamp with a hash value. The timestamp is used to calculate the
age of the cookie, allowing the relay to reject a message if the
cookie's age is greater than some maximum allowable value. If the
cookie has not expired, the relay uses the timestamp to lookup the
secret that was in use at that time and then compute and compare the
hash portion of the cookie to authenticate the message source.
A second purpose served by including the timestamp in the MAC field
is that it allows the relay to contribute an unpredictable value to
the authentication hash. This contribution provides a defense
against attempts to use a hash reversal algorithm to determine the
relay's private secret as the hash result will change over time even
if the nonce carried by the Request message does not.
Bumgardner Expires December 14, 2012 [Page 82]
Internet-Draft AMT June 2012
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| V=0 |4 or 5| Reserved | | Response MAC |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Request Nonce |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
: :
The Opaque Response MAC Field
A relay may use the opaque Response MAC field to store a cookie as
follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| V=0 |4 or 5| Reserved | | Timestamp |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| MD5(Secret,Timestamp,IP_ADDR,IP_PORT,Request-Nonce) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Request Nonce |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
: :
Using The Response MAC Field To Carry An Authentication Cookie
The timestamp is an unsigned integer measured relative to the start
time of relay. The age of the MAC is computed by subtracting the MAC
timestamp from the current system timestamp. The operands must be
unsigned 16-bit integers and the subtraction must use unsigned
arithmetic to allow for timestamp wrap-around. The timestamp
resolution must provide range sufficient to handle the maximum
allowable age for a MAC, e.g., a resolution of 1 second allows a
maximum age of 18 hours. The timestamp should start at a random
value by adding a random offset, computed at startup, to the current
system time.
Bumgardner Expires December 14, 2012 [Page 83]
Internet-Draft AMT June 2012
+-------------------------+----------------/ /-----------------+
-->| Timestamp(N1) [16-bits] | Random Secret [128-bits] |
| +-------------------------+----------------/ /-----------------+
|_____________________________________________________________________
|
+-------------------------+----------------/ /-----------------+ |
-->| Timestamp(N1) [16-bits] | Random Secret [128-bits] |--
| +-------------------------+----------------/ /-----------------+
|_____________________________________________________________________
|
+-------------------------+----------------/ /-----------------+ |
-->| Timestamp(N1) [16-bits] | Random Secret [128-bits] |--
| +-------------------------+----------------/ /-----------------+
|
|__ Current
Secret
Private Secret Queue
The timestamp is not only used to compute the age of the MAC, but is
also used to lookup the private secret used to generate the MAC.
Each time a new private secret is computed, the value and the time at
which the value was computed is pushed into a fixed-length queue of
recent values (typically only 2-deep). The relay uses the timestamp
contained in the MAC field to lookup the appropriate secret. The
relay iterates over the list of secrets, starting with the newest
entry, until it finds the first secret with a timestamp that is older
than that contained in the MAC field. The relay then uses that
secret to compute the MAC that will be compared with that carried by
the message.
Bumgardner Expires December 14, 2012 [Page 84]
Internet-Draft AMT June 2012
Author's Address
Gregory Bumgardner
Cisco
3700 Cisco Way
San Jose, CA 95134
USA
Phone: +1 408 853 4993
Email: gbumgard@cisco.com
Bumgardner Expires December 14, 2012 [Page 85]