Network Working Group J. Goldberg
Internet-Draft Cisco
Intended status: Standards Track M. Westerlund
Expires: November 8, 2012 Ericsson
T. Zeng
Nextwave Wireless, Inc.
May 7, 2012
A Network Address Translator (NAT) Traversal mechanism for media
controlled by Real-Time Streaming Protocol (RTSP)
draft-ietf-mmusic-rtsp-nat-12
Abstract
This document defines a solution for Network Address Translation
(NAT) traversal for datagram based media streams setup and controlled
with Real-time Streaming Protocol version 2 (RTSP 2.0). It uses
Interactive Connectivity Establishment (ICE) adapted to use RTSP as a
signalling channel, defining the necessary extra RTSP extensions and
procedures.
Status of this Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on November 8, 2012.
Copyright Notice
Copyright (c) 2012 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
Goldberg, et al. Expires November 8, 2012 [Page 1]
Internet-Draft A Media NAT Traversal mechanism for RTSP May 2012
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. Definitions . . . . . . . . . . . . . . . . . . . . . . . . . 4
3. Solution Overview . . . . . . . . . . . . . . . . . . . . . . 5
4. RTSP Extensions . . . . . . . . . . . . . . . . . . . . . . . 7
4.1. ICE Transport Lower Layer . . . . . . . . . . . . . . . . 7
4.2. ICE Candidate Transport Header Parameter . . . . . . . . . 8
4.3. ICE Password and Username Transport Header Parameters . . 11
4.4. ICE Feature Tag . . . . . . . . . . . . . . . . . . . . . 11
4.5. Status Codes . . . . . . . . . . . . . . . . . . . . . . . 12
4.5.1. 150 ICE connectivity checks in progress . . . . . . . 12
4.5.2. 480 ICE Processing Failed . . . . . . . . . . . . . . 12
4.6. New Reason for PLAY_NOTIFY . . . . . . . . . . . . . . . . 12
4.7. Server Side SDP Attribute for ICE Support . . . . . . . . 13
4.8. ICE Features Not Required in RTSP . . . . . . . . . . . . 13
4.8.1. ICE-Lite . . . . . . . . . . . . . . . . . . . . . . . 13
4.8.2. ICE-Mismatch . . . . . . . . . . . . . . . . . . . . . 13
4.8.3. ICE Remote Candidate Transport Header Parameter . . . 13
5. Detailed Solution . . . . . . . . . . . . . . . . . . . . . . 14
5.1. Session description and RTSP DESCRIBE (optional) . . . . . 14
5.2. Setting up the Media Streams . . . . . . . . . . . . . . . 15
5.3. RTSP SETUP Request . . . . . . . . . . . . . . . . . . . . 15
5.4. Gathering Candidates . . . . . . . . . . . . . . . . . . . 16
5.5. RTSP Server Response . . . . . . . . . . . . . . . . . . . 17
5.6. Server to Client ICE Connectivity Checks . . . . . . . . . 18
5.7. Client to Server ICE Connectivity Check . . . . . . . . . 18
5.8. Client Connectivity Checks Complete . . . . . . . . . . . 18
5.9. Server Connectivity Checks Complete . . . . . . . . . . . 19
5.10. Releasing Candidates . . . . . . . . . . . . . . . . . . . 19
5.11. Steady State . . . . . . . . . . . . . . . . . . . . . . . 19
5.12. Re-SETUP . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.13. Server Side Changes After Steady State . . . . . . . . . . 20
6. ICE and Proxies . . . . . . . . . . . . . . . . . . . . . . . 22
6.1. Media Handling Proxies . . . . . . . . . . . . . . . . . . 22
6.2. Signalling Only Proxies . . . . . . . . . . . . . . . . . 22
6.3. Non-supporting Proxies . . . . . . . . . . . . . . . . . . 23
7. RTP and RTCP Multiplexing . . . . . . . . . . . . . . . . . . 23
8. Fallback . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
9. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 25
9.1. RTSP Feature Tags . . . . . . . . . . . . . . . . . . . . 25
Goldberg, et al. Expires November 8, 2012 [Page 2]
Internet-Draft A Media NAT Traversal mechanism for RTSP May 2012
9.2. Transport Protocol Specifications . . . . . . . . . . . . 26
9.3. RTSP Transport Parameters . . . . . . . . . . . . . . . . 26
9.4. RTSP Status Codes . . . . . . . . . . . . . . . . . . . . 26
9.5. Notify-Reason value . . . . . . . . . . . . . . . . . . . 27
9.6. SDP Attribute . . . . . . . . . . . . . . . . . . . . . . 27
10. Security Considerations . . . . . . . . . . . . . . . . . . . 27
10.1. ICE and RTSP . . . . . . . . . . . . . . . . . . . . . . . 27
11. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 28
12. References . . . . . . . . . . . . . . . . . . . . . . . . . . 28
12.1. Normative References . . . . . . . . . . . . . . . . . . . 28
12.2. Informative References . . . . . . . . . . . . . . . . . . 29
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 30
Goldberg, et al. Expires November 8, 2012 [Page 3]
Internet-Draft A Media NAT Traversal mechanism for RTSP May 2012
1. Introduction
Real-time Streaming Protocol (RTSP) [RFC2326] and RTSP 2.0
[I-D.ietf-mmusic-rfc2326bis] is protocols used to setup and control
one or more media streams delivering media to receivers. It is
RTSP's functionality of setting up media streams that cause serious
issues with Network Address Translators (NAT) [RFC3022] unless extra
provisions are taken by the protocol. There is thus a need for a NAT
traversal mechanism for the media setup using RTSP.
RTSP 1.0 [RFC2326] has suffered from the lack of a standardized NAT
traversal mechanism for a long time, however due to quality of the
RTSP 1.0 specification, the work was difficult to specify in an
interoperable fashion. This documenent is therefore built on the
specification of RTSP 2.0 [I-D.ietf-mmusic-rfc2326bis]. RTSP 2.0 is
similar to RTSP 1.0 in many respects but significantly for this work,
it contains a well defined extension mechanism so allowing a NAT
traversal extension to be defined that is backwards compatible with
RTSP 2.0 peers not supporting the extension. This extension
mechanism was not possible in RTSP 1.0 as it would break RTSP 1.0
syntax so causing compatibility issues.
There have been a number of suggested ways of resolving the NAT-
traversal of media for RTSP of which a large number are already used
in implementations. The evaluation of these NAT traversal solutions
in [I-D.ietf-mmusic-rtsp-nat-evaluation] has shown that there are
many issues to consider, so after extensive evaluation, a mechanism
based on Interactive Connectivity Establishment (ICE) were selected.
This was mainly two reasons: Firstly the mechanism supports RTSP
servers behind NATs and secondly the mechanism mitigates the security
threat of using RTSP servers as Distributed Denial of Service (DDoS)
attack tools.
This document specifies an ICE based solution that is optimized for
media delivery server to client. If in the future extensions are
specified for other delivery modes than "PLAY", then the
optimizations in regards to when PLAY request are sent needs to be
reconsidered.
The NAT problem for RTSP signalling traffic itself is beyond the
scope of this document and is left for future study should the need
arise, because it is a less prevalent problem than the NAT problem
for RTSP media streams.
2. Definitions
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
Goldberg, et al. Expires November 8, 2012 [Page 4]
Internet-Draft A Media NAT Traversal mechanism for RTSP May 2012
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
3. Solution Overview
This overview assumes that the reader has some familiarity with how
ICE [RFC5245] in the context of "SIP: Session Initiation Protocol"
[RFC3261] and "An Offer/Answer Model with the Session Description
Protocol (SDP)" [RFC3264] works, as it primarily points out how the
different ICE steps are accomplished in RTSP.
1. RTSP server should indicate it has support for ICE via an SDP
[RFC4566] attribute ("a=rtsp-ice-d-m") in, for example, the SDP
returned in RTSP DESCRIBE message. This allows RTSP clients to
only send the new ICE interchanges with servers that support ICE
so as to limit the overhead on current non-ICE supporting RTSP
servers. If RTSP DESCRIBE is used the normal capability
determination mechanism should also be used, i.e. "Supported"
header and the defined feature tag. Note: Both mechanisms
should be used as there are use cases when either of them are
not used.
2. The RTSP client reviews the session description returned, for
example by an RTSP DESCRIBE message, to determine what media
streams need to be setup. For each of these media streams where
the transport protocol supports Session Traversal Utilities for
(NAT) (STUN) [RFC5389] based connectivity checks, the client
gathers candidate addresses. See section 4.1.1 in ICE
[RFC5245]. The client also installs the STUN servers on each of
the local candidates.
3. The RTSP client sends SETUP requests with both a transport
specification with a lower layer indicating ICE and a new RTSP
Transport header parameter "candidates" listing the ICE
candidates for each media stream.
4. After receiving the list of candidates from a client, the RTSP
server gathers its own candidates. If the server has a public
IP address, then a single candidate per address family (e.g.
IPv4 and IPv6), media stream and media component tuple can be
included to reduce the number of combinations and speed up the
completion.
5. The server sets up the media and if successful responds to the
SETUP request with a 200 OK response. In that response the
server selects the transport specification using ICE and
includes its candidates in the candidates parameter.
Goldberg, et al. Expires November 8, 2012 [Page 5]
Internet-Draft A Media NAT Traversal mechanism for RTSP May 2012
6. The server starts the connectivity checks following the
procedures described in Section 5.7 and 5.8 of ICE [RFC5245].
If the server has a public IP address with a single candidate
per media stream, component and address family then one may
configure the server to not initiate connectivity checks.
7. The client receives the SETUP response and learns the candidate
address to use for the connectivity checks, and then initiates
its connectivity check, following the procedures in Section 6 of
ICE [RFC5245].
8. When a connectivity check from the client reaches the server it
will result in a triggered check from the server. This is why
servers with a public IP address can wait until this triggered
check to send out any checks for itself, so saving resources and
mitigating the DDoS potential from server connectivity checks.
9. When the client has concluded its connectivity checks, including
promoting candidates, and has correspondingly received the
server connectivity checks on the promoted candidates for all
mandatory components of all media streams, it can issue a PLAY
request. If the connectivity checks have not concluded
successfully then the client may send a new SETUP request
assuming it has any new information or believes the server may
be able to do more that can result in successful checks.
10. When the RTSP servers receives a PLAY request it checks to see
the connectivity checks has concluded successfully and only then
can it play the stream. If there is a problem with the checks
then the server sends to the client either a 150 (ICE
connectivity checks in progress) response to show that it is
still working on the connectivity checks or a 480 (ICE
Processing Failed) response to indicate a failure of the checks.
If the checks are successful then the server sends a 200 OK
response and starts delivering media.
The client and server may release unused candidates when the ICE
processing has concluded and a single candidate per component has
been promoted and a PLAY response has been received (Client) or sent
(Server).
The client shall continue to use STUN to send keep-alive for the used
bindings. This is important as often RTSP media sessions only
contain media traffic from the server to the client so the bindings
in the NAT needs to be refreshed by the client to server traffic
provided by the STUN keep-alive.
Goldberg, et al. Expires November 8, 2012 [Page 6]
Internet-Draft A Media NAT Traversal mechanism for RTSP May 2012
4. RTSP Extensions
This section defines the necessary RTSP extensions for performing ICE
with RTSP. Note that these extensions are based on the SDP
attributes in the ICE specification unless expressly indicated.
4.1. ICE Transport Lower Layer
A new lower layer "D-ICE" for transport specifications is defined.
This lower layer is datagram clean except that the protocol used must
be demultiplexiable with STUN messages (see STUN [RFC5389]). With
datagram clean we mean that it must be capable of describing the
length of the datagram, transport that datagram (as a binary chunk of
data) and provide it at the receiving side as one single item. This
lower layer can be any transport type defined for ICE which does
provide datagram transport capabilities. UDP based transport
candidates are defined in ICE [RFC5245] and MUST be supported. It is
OPTIONAL to also support TCP based candidates as defined by "TCP
Candidates with Interactive Connectivity Establishment (ICE)"
[RFC6544]. The TCP based candidate fulfills the requirements on
providing datagram transport and can thus be used in combination with
RTP. Additional transport types for candidates may be defined in the
future.
This lower layer uses ICE to determine which of the different
candidates shall be used and then when the ICE processing has
concluded, uses the selected candidate to transport the datagrams
over this transport.
This lower layer transport can be combined with all upper layer media
transport protocols that are possible to demultiplex with STUN and
which use datagrams. This specification defines the following
combinations:
o RTP/AVP/D-ICE
o RTP/AVPF/D-ICE
o RTP/SAVP/D-ICE
o RTP/SAVPF/D-ICE
This list can easily be extended with more transport specifications
after having performed the evaluation that they are compatible with
D-ICE as lower layer.
The lower-layer "D-ICE" has the following rules for the inclusion of
transport parameters:
Goldberg, et al. Expires November 8, 2012 [Page 7]
Internet-Draft A Media NAT Traversal mechanism for RTSP May 2012
unicast: As ICE only supports unicast operations, thus it is
REQUIRED that one include the unicast indicator parameter, see
section 16.46 in RTSP 2.0 [I-D.ietf-mmusic-rfc2326bis].
candidates: The "candidates" parameter SHALL be included as this
specify at least one candidate to try to establish a working
transport path with.
dest_addr: This parameter SHALL NOT be included as "candidates" is
used instead to provide the necessary address information.
ICE-Password: This parameter SHALL be included.
ICE-ufrag: This parameter SHALL be included.
4.2. ICE Candidate Transport Header Parameter
This section defines a new RTSP transport parameter for carrying ICE
candidates related to the transport specification they appear within,
which may then be validated with an end-to-end connectivity check
using STUN [RFC5389]. Transport parameters may only occur once in
each transport specification. For transport specification using
"D-ICE" as lower layer, this parameter needs to be present. The
parameter can contain one or more ICE candidates. In the SETUP
response there is only a single transport specification, and if that
uses the "D-ICE" lower layer this parameter MUST be present and
include the server side candidates.
Goldberg, et al. Expires November 8, 2012 [Page 8]
Internet-Draft A Media NAT Traversal mechanism for RTSP May 2012
trns-parameter = <Defined in Section 20.2.3 of
[I-D.ietf-mmusic-rfc2326bis]>
trns-parameter =/ SEMI ice-trn-par
ice-trn-par = "candidates" EQUAL DQ SWS ice-candidate
*(SEMI ice-candidate) SWS DQ
ice-candidate = foundation SP
component-id SP
transport SP
priority SP
connection-address SP
port SP
cand-type
[SP rel-addr]
[SP rel-port]
[SP tcp-type-ext] ; Mandatory if transport = TCP
*(SP extension-att-name SP extension-att-value)
foundation = <See section 15.1 of [RFC5245]>
component-id = <See section 15.1 of [RFC5245]>
transport = <See section 15.1 of [RFC5245]>
transport-extension = <See section 15.1 of [RFC5245]>
priority = <See section 15.1 of [RFC5245]>
cand-type = <See section 15.1 of [RFC5245]>
candidate-types = <See section 15.1 of [RFC5245]>
rel-addr = <See section 15.1 of [RFC5245]>
rel-port = <See section 15.1 of [RFC5245]>
tcp-type-ext = <See section 4.5 of [RFC6544]>
extension-att-name = <See section 15.1 of [RFC5245]>
extension-att-value = <See section 15.1 of [RFC5245]>
ice-char = <See section 15.1 of [RFC5245]>
connection-address = <See [RFC4566]>
port = <See [RFC4566]>
EQUAL = <Defined in [I-D.ietf-mmusic-rfc2326bis]>
DQ = <Defined in [I-D.ietf-mmusic-rfc2326bis]>
SWS = <Defined in [I-D.ietf-mmusic-rfc2326bis]>
SEMI = <Defined in [I-D.ietf-mmusic-rfc2326bis]>
<connection-address>: is the IP address of the candidate, allowing
for IPv4 addresses, IPv6 addresses and Fully qualified domain
names (FQDN), taken from ICE [RFC4566]. The connection address
SHOULD be on the same format (explicit IP or FQDN) as in the
dest_addr parameter used to express fallbacks. An IP address
SHOULD be used, but an FQDN MAY be used in place of an IP address.
In that case, when receiving an SETUP request or response
containing an FQDN in an candidate parameter, the FQDN is looked
up in the DNS first using an AAAA record (assuming the agent
supports IPv6), and if no result is found or the agent only
supports IPv4, using an A record. If the DNS query returns more
Goldberg, et al. Expires November 8, 2012 [Page 9]
Internet-Draft A Media NAT Traversal mechanism for RTSP May 2012
than one IP address, one is chosen, and then used for the
remainder of ICE processing which in RTSP is subsequent RTSP
SETUPs for the same RTSP session.
<port>: is the port of the candidate, the syntax defined by SDP
[RFC4566].
<transport>: indicates the transport protocol for the candidate.
The ICE specification defines UDP. "TCP Candidates with
Interactive Connectivity Establishment (ICE)" [RFC6544] defines
how TCP is used as candidates. Additional extensibility is
provided to allow for future transport protocols to be used with
ICE, such as the Datagram Congestion Control Protocol (DCCP)
[RFC4340].
<foundation>: is an identifier that is equivalent for two
candidates that are of the same type, share the same base, and
come from the same STUN server, and is composed of one to thirty
two <ice-char>. The foundation is used to optimize ICE
performance in the Frozen algorithm.
<component-id>: identifies the specific component of the media
stream for which this is a candidate and os a positive integer
between 1 and 256. It MUST start at 1 and MUST increment by 1 for
each component of a particular candidate. For media streams based
on RTP, candidates for the actual RTP media MUST have a component
ID of 1, and candidates for RTCP MUST have a component ID of 2.
Other types of media streams which require multiple components
MUST develop specifications which define the mapping of components
to component IDs. See Section 14 for additional discussion on
extending ICE to new media streams.
<priority>: is a positive integer between 1 and (2**31 - 1).
<cand-type>: encodes the type of candidate. The ICE specification
defines the values "host", "srflx", "prflx" and "relay" for host,
server reflexive, peer reflexive and relayed candidates,
respectively. The set of candidate types is extensible for the
future.
<rel-addr> and <rel-port>: convey transport addresses related to the
candidate, useful for diagnostics and other purposes. <rel-addr>
and <rel-port> MUST be present for server reflexive, peer
reflexive and relayed candidates. If a candidate is server or
peer reflexive, <rel-addr> and <rel-port> is equal to the base for
that server or peer reflexive candidate. If the candidate is
relayed, <rel-addr> and <rel-port> is equal to the mapped address
in the Allocate Response that provided the client with that
Goldberg, et al. Expires November 8, 2012 [Page 10]
Internet-Draft A Media NAT Traversal mechanism for RTSP May 2012
relayed candidate (see Appendix B.3 of ICE [RFC5245] for a
discussion of its purpose). If the candidate is a host candidate
<rel-addr> and <rel-port> MUST be omitted.
<tcp-type-ext>: conveys the candidates connection type (active,
passive, or S-O) for TCP based candidates. This MUST be included
for candidates that has <transport> set to TCP and MUST NOT be
included for other transport types, including UDP, unless
explicitly specified for that transport protocol.
4.3. ICE Password and Username Transport Header Parameters
The ICE password and username for each agent needs to be transported
using RTSP. For that purpose new transport header parameters are
defined.
There MUST be an "ICE-Password" and "ICE-ufrag" parameter for each
media stream. If two SETUP requests in the same RTSP session have
identical ICE-ufrag's, they MUST have identical ICE-Password's. The
ICE-ufrag and ICE-Password attributes MUST be chosen randomly at the
beginning of a session. The ICE-ufrag attribute MUST contain at
least 24 bits of randomness, and the ICE-Password attribute MUST
contain at least 128 bits of randomness. This means that the ICE-
ufrag attribute will be at least 4 characters long, and the ICE-
Password at least 22 characters long, since the grammar for these
attributes allows for 6 bits of randomness per character. The
attributes MAY be longer than 4 and 22 characters respectively, of
course, up to 256 characters. The upper limit allows for buffer
sizing in implementations. Its large upper limit allows for
increased amounts of randomness to be added over time.
The ABNF [RFC5234] for these parameters are:
trns-parameter =/ SEMI ice-password-par
trns-parameter =/ SEMI ice-ufrag-par
ice-password-par = "ICE-Password" EQUAL DQ password DQ
ice-ufrag-par = "ICE-ufrag" EQUAL DQ ufrag DQ
password = <Defined in [RFC5245]>
ufrag = <Defined in [RFC5245]>
EQUAL = <Defined in [I-D.ietf-mmusic-rfc2326bis]>
SEMI = <Defined in [I-D.ietf-mmusic-rfc2326bis]>
DQ = <Defined in [I-D.ietf-mmusic-rfc2326bis]>
4.4. ICE Feature Tag
A feature tag is defined for use in the RTSP capabilities mechanism
for ICE support of media transport using datagrams: "setup.ice-d-m".
This feature tag indicates that one supports all the mandatory
functions of this specification. It is applicable to all types of
Goldberg, et al. Expires November 8, 2012 [Page 11]
Internet-Draft A Media NAT Traversal mechanism for RTSP May 2012
RTSP agents; clients, servers and proxies.
The RTSP client SHOULD send the feature tag "setup.ice-d-m" in the
"Supported" header in all SETUP requests that contain the "D-ICE"
lower layer transport.
4.5. Status Codes
ICE needs two new RTSP response codes to indicate correctly progress
and errors.
+------+----------------------------------------------+-------------+
| Code | Reason | Method |
+------+----------------------------------------------+-------------+
| 150 | Server still working on ICE connectivity | PLAY |
| | checks | |
| 480 | ICE Connectivity check failure | PLAY, SETUP |
+------+----------------------------------------------+-------------+
Table 1: New Status codes and their usage with RTSP methods
4.5.1. 150 ICE connectivity checks in progress
The 150 response code indicates that ICE connectivity checks are
still in progress and haven't concluded. This response SHALL be sent
within 200 milliseconds of receiving a PLAY request that currently
can't be fulfilled because ICE connectivity checks are still running.
Subsequently, every 3 seconds after the previous sent one, a 150
reply shall be sent until the ICE connectivity checks conclude either
successfully or in failure, and a final response for the request can
be provided.
4.5.2. 480 ICE Processing Failed
The 480 client error response code is used in cases when the request
can't be fulfilled due to a failure in the ICE processing, such as
that all the connectivity checks have timed out. This error message
can appear either in response to a SETUP request to indicate that no
candidate pair can be constructed or to a PLAY request that the
server's connectivity checks resulted in failure.
4.6. New Reason for PLAY_NOTIFY
A new value used in the PLAY_NOTIFY methods Notify-Reason header is
defined: "ice-restart". This reason indicates that a ICE restart
needs to happen on the identified resource and session.
Notify-Reas-val =/ "ice-restart"
Goldberg, et al. Expires November 8, 2012 [Page 12]
Internet-Draft A Media NAT Traversal mechanism for RTSP May 2012
4.7. Server Side SDP Attribute for ICE Support
If the server supports the media NAT traversal for RTSP controlled
sessions, as described in this RFC, then the Server SHOULD include
the "a=rtsp-ice-d-m" SDP attribute in any SDP (if used) describing
content served by the server. This is an session level attribute.
rtsp-ice-d-m-attr = "a=" "rtsp-ice-d-m"
4.8. ICE Features Not Required in RTSP
A number of ICE signalling features are not needed with RTSP and are
discussed below.
4.8.1. ICE-Lite
The ICE-Lite attribute shall not be used in the context of RTSP. The
ICE specification describes two implementations of ICE: Full and
Lite, where hosts that are not behind a NAT are allowed to implement
only Lite. For RTSP, the Lite implementation is insufficient because
it does not cause the media server to send a connectivity check,
which are used to protect against making the RTSP server a denial of
service tool. This document defines another variation implementation
of ICE, called ICE-RTSP. It has its own set of simplifications
suitable to RTSP. Conceptually, this implementation of ICE-RTSP is
between ICE-FULL and ICE-LITE for a server and simpler than ICE-FULL
for clients.
4.8.2. ICE-Mismatch
The ice-mismatch parameter indicates that the offer arrived with a
default destination for a media component that didn't have a
corresponding candidate attribute. This is not needed for RTSP as
the ICE based lower layer transport specification either is supported
or another alternative transport is used. This is always explicitly
indicated in the SETUP request and response.
4.8.3. ICE Remote Candidate Transport Header Parameter
The Remote candidate attribute is not needed for RTSP for the
following reasons. Each SETUP results in a independent ICE
processing chain which either fails or results in promoting a single
candidate pair to usage. If a new SETUP request for the same media
is sent this needs to use a new userfragment and password to avoid
any race conditions or uncertainty for which processing round the
STUN requests relate to.
Goldberg, et al. Expires November 8, 2012 [Page 13]
Internet-Draft A Media NAT Traversal mechanism for RTSP May 2012
5. Detailed Solution
This section describes in detail how the interaction and flow of ICE
works with RTSP messages.
5.1. Session description and RTSP DESCRIBE (optional)
The RTSP server should indicate it has support for ICE by sending the
"a=rtsp-ice-d-m" SDP attribute in the response to the RTSP DESCRIBE
message if SDP is used. This allows RTSP clients to only send the
new ICE interchanges with servers that support ICE so limiting the
overhead on current non-ICE supporting RTSP servers. When not using
RTSP DESCRIBE it is still recommended to use the SDP attribute for
session description.
A Client can also use the DESCRIBE request to determine explicitly if
both server and any proxies support ICE. The client includes the
"Supported" header with its supported feature tags, including
"setup.ice-d-m". Any proxy upon seeing the "Supported" header will
include the "Proxy-Supported" header with the feature tags it
supports. The server will echo back the "Proxy-Supported" header and
its own version of the Supported header so enabling a client to
determine if all involved parties support ICE or not. Note that even
if a proxy is present in the chain that doesn't indicate support for
ICE, it may still work.
Goldberg, et al. Expires November 8, 2012 [Page 14]
Internet-Draft A Media NAT Traversal mechanism for RTSP May 2012
For example:
C->S: DESCRIBE rtsp://server.example.com/fizzle/foo RTSP/2.0
CSeq: 312
User-Agent: PhonyClient 1.2
Accept: application/sdp, application/example
Supported: setup.ice-d-m, setup.rtp.rtcp.mux
S->C: RTSP/2.0 200 OK
CSeq: 312
Date: 23 Jan 1997 15:35:06 GMT
Server: PhonyServer 1.1
Content-Type: application/sdp
Content-Length: 367
Supported: setup.ice-d-m, setup.rtp.rtcp.mux
v=0
o=mhandley 2890844526 2890842807 IN IP4 192.0.2.46
s=SDP Seminar
i=A Seminar on the session description protocol
u=http://www.example.com/lectures/sdp.ps
e=seminar@example.com (Seminar Management)
t=2873397496 2873404696
a=recvonly
a=rtsp-ice-d-m
a=control: *
m=audio 3456 RTP/AVP 0
a=control: /audio
m=video 2232 RTP/AVP 31
a=control: /video
5.2. Setting up the Media Streams
The RTSP client reviews the session description returned, for example
by an RTSP DESCRIBE message, to determine what media resources that
need to be setup. For each of these media streams where the
transport protocol supports ICE connectivity checks, the client SHALL
gather candidate addresses for UDP transport as described in section
4.1.1 in ICE [RFC5245] according to standard ICE rather than the ICE-
Lite implementation and according to section 5 of ICE TCP [RFC6544]
for TCP based candidates.
5.3. RTSP SETUP Request
The RTSP client will then send at least one SETUP request per media
stream to establish the media streams required for the desired
session. For each media stream where it desires to use ICE it will
include a transport specification with "D-ICE" as the lower layer,
and each media stream SHALL have its own unique combination of ICE
Goldberg, et al. Expires November 8, 2012 [Page 15]
Internet-Draft A Media NAT Traversal mechanism for RTSP May 2012
candidates and ICE-ufrag. This transport specification SHOULD be
placed first in the list to give it highest priority. It is
RECOMMENDED that additional transport specifications are provided as
a fallback in case of non ICE supporting proxies. The RTSP client
will be initiating and thus the controlling party in the ICE
processing. For example (Note that some lines are broken in
contradiction with the defined syntax due to space restrictions in
the documenting format:
C->S: SETUP rtsp://server.example.com/fizzle/foo/audio RTSP/2.0
CSeq: 313
Transport: RTP/AVP/D-ICE; unicast; ICE-ufrag=8hhY;
ICE-Password=asd88fgpdd777uzjYhagZg; candidates="
1 1 UDP 2130706431 10.0.1.17 8998 typ host;
2 1 UDP 1694498815 192.0.2.3 45664 typ srflx
raddr 10.0.1.17 rport 8998"; RTCP-mux,
RTP/AVP/UDP; unicast; dest_addr=":6970"/":6971",
RTP/AVP/TCP;unicast;interleaved=0-1
Accept-Ranges: NPT, UTC
User-Agent: PhonyClient/1.2
Supported: setup.ice-d-m, setup.rtp.rtcp.mux
5.4. Gathering Candidates
Upon receiving a SETUP request the server can determine what media
resource should be delivered and which transport alternatives that
the client supports. If one based on D-ICE is on the list of
supported transports and prefered among the supported, the below
applies.
The transport specification will provide which media protocol is to
be used and based on this and the clients candidates, the server
determines the protocol and if it supports ICE with that protocol.
The server shall then gather its UDP candidates according to section
4.1.1 in ICE [RFC5245] and any TCP based ones according to section 5
of ICE TCP [RFC6544].
Servers that have an address that is generally reachable by any
clients within the address scope the server intends to serve MAY be
specially configured (high-reachability configuration). This special
configuration has the goal of reducing the server side candidate to
preferably a single one per (address family, media stream, media
component) tuple. Instead of gathering all possible addresses
including relayed and server reflexive addresses, the server uses a
single address per address family that it knows it should be
reachable by a client behind one or more NATs. The reason for this
special configuration is two fold: Firstly it reduces the load on the
server in address gathering and in ICE processing during the
Goldberg, et al. Expires November 8, 2012 [Page 16]
Internet-Draft A Media NAT Traversal mechanism for RTSP May 2012
connectivity checks. Secondly it will reduce the number of
permutations for candidate pairs significantly thus potentially
speeding up the conclusion of the ICE processing. Note however that
using this option on a server that doesn't fulfill the requirement of
being reachable is counter-productive and it is important that this
is correctly configured.
The above general consideration for servers applies also for TCP
based candidates. A general implementation should support several
candidate collection techniques and connection types. For TCP based
candidates a high-reachability configured server is recommended to
only offer Host candidates. In addition to passive connection types
the server can select to provide active or SO conenction types to
match the client's candidates.
5.5. RTSP Server Response
The server determines if the SETUP request is successful from the
other perspectives and will return a 200 OK response, otherwise
returning an error code. At that point the server, having selected a
transport specification using the "D-ICE" lower layer, will need to
include that transport specification in the response message. The
transport specification shall include the candidates gathered in
Section 5.4 in the "candidates" transport header parameter as well as
the server's username and password fragments. In the case that there
are no valid candidate pairs with the combination of the client and
servers candidates, a 480 (ICE Processing Failed) error response
SHALL be returned which MUST include the servers' candidates. The
return of a 480 error allows both the server and client to release
its candidates.
Example of a succesful response to the request in Section 5.3.
S->C: RTSP/2.0 200 OK
CSeq: 313
Session: 12345678
Transport: RTP/AVP/D-ICE; unicast; RTCP-mux; ICE-ufrag=MkQ3;
ICE-Password=pos12Dgp9FcAjpq82ppaF; candidates="
1 1 UDP 2130706431 192.0.2.56 50234 typ host"
Accept-Ranges: NPT
Date: 23 Jan 1997 15:35:06 GMT
Server: PhonyServer 1.1
Supported: setup.ice-d-m, setup.rtp.rtcp.mux
Goldberg, et al. Expires November 8, 2012 [Page 17]
Internet-Draft A Media NAT Traversal mechanism for RTSP May 2012
5.6. Server to Client ICE Connectivity Checks
The server shall start the connectivity checks following the
procedures described in Section 5.7 and 5.8 of ICE [RFC5245] unless
it is configured to use the high-reachability option. If it is then
it MAY suppress its own checks until the servers checks are triggered
by the client's connectivity checks.
Please note that section 5.8 does specify that the initiation of the
checks are paced and new ones are only started every Ta milliseconds.
The motivation for this is documented in Appendix B.1 of ICE
[RFC5245] as for SIP/SDP all media streams within an offer/answer
dialog are running using the same queue. To ensure the same behavior
with RTSP, the server SHALL use a single pacer queue for all media
streams within each RTSP session.
The values for the pacing of STUN and TURN transactions Ta and RTO
can be configured but have the same minimum values defined in the ICE
specification.
When a connectivity check from the client reaches the server it will
result in a triggered check from the server as specified in section
7.2.1.4 of ICE [RFC5245]. This is why servers with a high
reachability address can wait until this triggered check to send out
any checks for itself so saving resources and mitigating the DDoS
potential.
5.7. Client to Server ICE Connectivity Check
The client receives the SETUP response and learns the candidate
address to use for the connectivity checks. The client shall
initiate its connectivity check, following the procedures in Section
6 of ICE [RFC5245]. The STUN transaction pacer SHALL be used across
all media streams part of the same RTSP session.
Aggressive nomination SHALL be used with RTSP. This doesn't have the
negative impact that it has in offer/answer as media playing only
starts after issuing a PLAY request.
5.8. Client Connectivity Checks Complete
When the client has concluded all of its connectivity checks and has
nominated its desired candidate for a particular media stream, it MAY
issue a PLAY request for that stream. Note, that due to the
aggressive nomination, there is a risk that any outstanding check may
nominate another pair than what was already nominated. If the client
has locally determined that its checks have failed it may try
providing an extended set of candidates and update the server
Goldberg, et al. Expires November 8, 2012 [Page 18]
Internet-Draft A Media NAT Traversal mechanism for RTSP May 2012
candidate list by issuing a new SETUP request for the media stream.
If the client concluded its connectivity checks successfully and
therefore sent a PLAY request but the server cannot conclude
successfully, the server will respond with a 480 (ICE Processing
Failed). Upon receiving the 480 (ICE Processing Failed) response,
the client may send a new SETUP request assuming it has any new
information that can be included in the candidate list. If the
server is still performing the checks when receiving the PLAY request
it will respond with a 150 (CE connectivity checks in progress)
response to indicate this.
5.9. Server Connectivity Checks Complete
When the RTSP server receives a PLAY request, it checks to see that
the connectivity checks have concluded successfully and only then
will it play the stream. If the PLAY request is for a particular
media stream, the server only needs to check that the connectivity
checks for that stream completely successfully. If the server has
not concluded its connectivity checks the server indicates that by
sending the 150 (ICE connectivity checks in progress)
(Section 4.5.1). If there is a problem with the checks then the
server sends to the client a 480 response to indicate a failure of
the checks. If the checks are successful then the server sends a 200
OK response and starts delivering media.
5.10. Releasing Candidates
Both server and client MAY release its non nominated candidates as
soon as a 200 PLAY response has been issued/received and no
outstanding connectivity checks exist.
5.11. Steady State
The client and server SHALL use STUN to send keep-alive for the
nominated candidate pair(s) following the rules of Section 10 of ICE
[RFC5245]. This is important as normally RTSP play mode sessions
only contain traffic from the server to the client so the bindings in
the NAT need to be refreshed by the client to server traffic provided
by the STUN keep-alive.
5.12. Re-SETUP
The server SHALL support SETUP requests in PLAYING state, as long as
the SETUP changes only the ICE parameters, which are: ICE-Password,
ICE-ufrag and the content of ICE candidates.
If the client decides to change any parameters related to the media
Goldberg, et al. Expires November 8, 2012 [Page 19]
Internet-Draft A Media NAT Traversal mechanism for RTSP May 2012
stream setup it will send a new SETUP request. In this new SETUP
request the client MAY include a new different username and password
to use in the ICE processing. New username and passwords SHALL cause
the ICE processing to start from the beginning again, i.e. an ICE
restart. The client SHALL in case of ICE restart gather candidates
and include the candidates in the transport specification for D-ICE.
If the RTSP session is in playing state at the time of sending the
SETUP request requiring ICE restart, then the ICE connectivity checks
SHALL use Regular nomination. Any ongoing media delivery continues
on the previously nominated candidate pairs until the new pairs have
been nominated for the individual candidate. Once the nomination of
the new candidate pair has completed, all unused candidates may be
released.
5.13. Server Side Changes After Steady State
A Server may require an ICE restart because of server side load
balancing or a failure resulting in an IP address and a port number
change. It shall use the PLAY_NOTIFY method to inform the client
(Section 13.5 [I-D.ietf-mmusic-rfc2326bis]) with a new Notify-Reason
header: ice-restart. The server will identify if the change is for a
single media or for the complete session by including the
corresponding URI in the PLAY_NOTIFY request.
Upon receiving and responding to this PLAY_NOTIFY with ice-restart
reason the client SHALL gather new ICE candidates, send SETUP
requests for each media stream part of the session. The server
provides its candidates in the SETUP response the same way as for the
first time ICE processing. Both server and client shall provide new
ICE usernames and passwords. The client MAY issue the SETUP request
while the session is in PLAYING state.
If the RTSP session is in PLAYING state when the client issues the
SETUP request, the client SHALL use regular nomination. If not the
client will use the same procedures as for when first creating the
session.
Note that keepalives on the previous set of candidate pairs should
continue until all new candidate pairs have been nominated. After
having nominated a new set of candidate pairs, the client may
continue to receive media for some additional time. Even if the
server stops delivering media over that candidate pair at the time of
nomination, media may arrive for up to one maximum segment lifetime
as defined in TCP (2 minutes). Unfortuntately, if the RTSP server is
divided into a separate controller and media streame, a failure may
result in continued media delivery for a longer time than the maximum
segment liftime, thus source filtering is recommended.
Goldberg, et al. Expires November 8, 2012 [Page 20]
Internet-Draft A Media NAT Traversal mechanism for RTSP May 2012
For example:
S->C: PLAY_NOTIFY rtsp://example.com/fizzle/foo RTSP/2.0
CSeq: 854
Notify-Reason: ice-restart
Session: uZ3ci0K+Ld
Server: PhonyServer 1.1
C->S: RTSP/2.0 200 OK
CSeq: 854
User-Agent: PhonyClient/1.2
C->S: SETUP rtsp://server.example.com/fizzle/foo/audio RTSP/2.0
CSeq: 314
Session: uZ3ci0K+Ld
Transport: RTP/AVP/D-ICE; unicast; ICE-ufrag=Kl1C;
ICE-Password=H4sICGjBsEcCA3Rlc3RzLX; candidates="
1 1 UDP 2130706431 10.0.1.17 8998 typ host;
2 1 UDP 1694498815 192.0.2.3 51456 typ srflx
raddr 10.0.1.17 rport 9002"; RTCP-mux,
RTP/AVP/UDP; unicast; dest_addr=":6970"/":6971",
RTP/AVP/TCP;unicast;interleaved=0-1
Accept-Ranges: NPT, UTC
User-Agent: PhonyClient/1.2
C->S: SETUP rtsp://server.example.com/fizzle/foo/video RTSP/2.0
CSeq: 315
Session: uZ3ci0K+Ld
Transport: RTP/AVP/D-ICE; unicast; ICE-ufrag=hZv9;
ICE-Password=JAhA9myMHETTFNCrPtg+kJ; candidates="
1 1 UDP 2130706431 10.0.1.17 9000 typ host;
2 1 UDP 1694498815 192.0.2.3 51576 typ srflx
raddr 10.0.1.17 rport 9000"; RTCP-mux,
RTP/AVP/UDP; unicast; dest_addr=":6972"/":6973",
RTP/AVP/TCP;unicast;interleaved=0-1
Accept-Ranges: NPT, UTC
User-Agent: PhonyClient/1.2
S->C: RTSP/2.0 200 OK
CSeq: 314
Session: uZ3ci0K+Ld
Transport: RTP/AVP/D-ICE; unicast; RTCP-mux; ICE-ufrag=CbDm;
ICE-Password=OfdXHws9XX0eBr6j2zz9Ak; candidates="
1 1 UDP 2130706431 192.0.2.56 50234 typ host"
Accept-Ranges: NPT
Date: 11 March 2011 13:17:46 GMT
Server: PhonyServer 1.1
Goldberg, et al. Expires November 8, 2012 [Page 21]
Internet-Draft A Media NAT Traversal mechanism for RTSP May 2012
S->C: RTSP/2.0 200 OK
CSeq: 315
Session: uZ3ci0K+Ld
Transport: RTP/AVP/D-ICE; unicast; RTCP-mux; ICE-ufrag=jigs;
ICE-Password=Dgx6fPj2lsa2WI8b7oJ7+s; candidates="
1 1 UDP 2130706431 192.0.2.56 47233 typ host"
Accept-Ranges: NPT
Date: 11 March 2011 13:17:47 GMT
Server: PhonyServer 1.1
6. ICE and Proxies
RTSP allows for proxies which can be of two fundamental types
depending if they relay and potentially cache the media or not.
Their differing impact on the RTSP NAT traversal solution, including
backwards compatibility, is explained below.
6.1. Media Handling Proxies
An RTSP proxy that relays or caches the media stream for a particular
media session can be considered to split the media transport into two
parts: A media transport between the server and the proxy according
to the proxies need, and delivery from the proxy to the client. This
split means that the NAT traversal solution will need to be run on
each individual media leg according to need.
It is RECOMMENDED that any media handling proxy support the media NAT
traversal defined within this specification. This is for two
reasons: Firstly to enable clients to perform NAT traversal for the
media between the proxy and itself and secondly to allow the proxy to
be topology independent so able to support performing NAT traversal
for non-NAT traversal capable clients present in the same address
domain.
For a proxy to support the media NAT traversal defined in this
specification a proxy will need to implement the solution fully and
be ready as both a controlling and a controlled ICE peer. The proxy
also SHALL include the "setup.ice-d-m" feature tag in any applicable
capability negotiation headers, such as "Proxy-Supported."
6.2. Signalling Only Proxies
A signalling only proxy handles only the RTSP signalling and does not
have the media relayed through proxy functions. This type of proxy
is not likely to work unless the media NAT traversal solution is in
place between the client and the server, because the DoS protection
measures usually prevent media delivery to other addresses other than
Goldberg, et al. Expires November 8, 2012 [Page 22]
Internet-Draft A Media NAT Traversal mechanism for RTSP May 2012
from where the RTSP signalling arrives at the server.
The solution for the Signalling Only proxy is that it must forward
the RTSP SETUP requests including any transport specification with
the "D-ICE" lower layer and the related transport parameters. A
proxy supporting this functionality SHOULD indicate its capability by
always including the "setup.ice-d-m" feature tag in the "Proxy-
Supported" header.
6.3. Non-supporting Proxies
A media handling proxy that doesn't support the ICE media NAT
traversal specified here is assumed to remove the transport
specification and use any of the lower prioritized transport
specifications if provided by the requester. The specification of
such a non ICE transport enables the negotiation to complete,
although with a less prefered method as a NAT between the proxy and
the client will likely result in failure of the media path.
A non-media handling proxy is expected to ignore and simply forward
all unknown transport specifications, however, this can only be
guaranteed for proxies following the published RTSP 2.0
specification.
Unfortunately the usage of the "setup.ice-d-m" feature tag in the
Proxy-Require will have contradicting results. For a non ICE
supporting media handling proxy, the inclusion of the feature tag
will result in aborting the setup and indicating that it isn't
supported, which is desirable if you want to provide other fallbacks
or other transport configurations to handle the situation. For non-
supporting non-media handling proxies the result will also result in
aborting the setup, however, setup might have worked if the proxy-
require tag wasn't present. This variance in results is the reason
we don't recommend the usage of the Proxy-Require header. Instead we
recommend the usage of the Supported header to force proxies to
include the feature tags they support in the proxy-supported which
will provide a positive indication when all proxies in the chain
between the client and server support the functionality. Even if not
explicitly indicating support, any SETUP response including a
transport specification with "D-ICE" will be implicit indication that
the proxy chain supports at least passthrough of this media.
7. RTP and RTCP Multiplexing
"Multiplexing RTP Data and Control Packets on a Single Port"
[RFC5761] specifies how and when RTP and RTCP can be multiplexed on
the same port. This multiplexing SHALL be combined with ICE as it
Goldberg, et al. Expires November 8, 2012 [Page 23]
Internet-Draft A Media NAT Traversal mechanism for RTSP May 2012
makes RTP and RTCP need only a single component per media stream
instead of two, so reducing the load on the connectivity checks. For
details on how one negotiate RTP and RTCP multiplexing, see Appendix
B of RTSP 2.0 [I-D.ietf-mmusic-rfc2326bis].
Multiplexing RTP and RTCP has the benefit that it avoids the need for
handling two components per media stream when RTP is used as the
media transport protocol. This eliminates at least one STUN check
per media stream and will also reduce the time needed to complete the
ICE processing by at least the time it takes to pace out the
additional STUN checks of up to one complete round trip time for a
single media stream. In addition to the protocol performance
improvements, the server and client side complexities are reduced as
multiplexing halves the total number of STUN instances and holding
the associate state. Multiplexing will also reduce the combinations
and length of the list of possible candidates.
The implementation of RTP and RTCP multiplexing is additional work
required for this solution. However, when implementing the ICE
solution a server or client will need to implement a de-multiplexer
between the STUN, and RTP or RTCP packets below the RTP/RTCP
implementation anyway, so the additional work of one new
demultiplexing point directly connected to the STUN and RTP/RTCP
seems small relative to the benefits provided.
Due to the above mentioned benefits, RTSP servers and clients that
supports "D-ICE" lower layer transport in combination with RTP SHALL
also implement RTP and RTCP multiplexing as specified in this section
and [RFC5761].
8. Fallback
The need for fallback from ICE in RTSP should be less than for SIP
using ICE in SDP offer/answer where a default destination candidate
is very important. This as capability determination for ICE can
happen prior to the RTSP SETUP request. Thus a client should
normally not needed to include fallback alternatives when offering
ICE, as the capability for ICE will already be determined. Thus this
section likely applies more to the cases where the server is not ICE
capable and the client wishes to use part of the ICE functionality to
improve NAT/Firewall traversal.
Section 4.1.4 of the ICE [RFC5245] specification does recommend that
the default destination, i.e. what is used in fallback if the peer
isn't ICE capable is a candidate of relayed type to maximize the
likelyhood of succesfull transport of media. This is based on that
the peer in SIP SDP offer/answer is almost as likely as the RTSP
Goldberg, et al. Expires November 8, 2012 [Page 24]
Internet-Draft A Media NAT Traversal mechanism for RTSP May 2012
client to be behind a NAT. For RTSP the deployement of servers are
much more heavily weighted towards deployment with public
reachability. In fact due to that servers behind NAT either needs to
support ICE or have static configurations that allow traversal one
can assume that the server will have a public address or support ICE.
Thus, the selection of the default destination address for RTSP can
be differently prioritized.
As an ICE enabled client needs to configured with a STUN server
address to be able to gather candidates successfully, this can be
utilized to derive a server reflexive candidate for the clients port.
How useful this is for an RTSP client as default candidate depends on
the properties of the NAT. As long as the NAT use an address
independent mapping, then using a STUN derived reflexive candidate is
likely to be successfully. This is however brittle in several ways.
First, the NATs behavior can be determined using STUN as described in
[RFC3489], however this might not be represenative of the behavior
encountered in another mapping. Secondly, filter state towards the
ports used by the server needs to be established. This requires that
the server actually include both address and ports in its response to
the SETUP request. Thirdly messages needs to be sent to these ports
for keep-alive at a regular interval. How a server reacts to such
unsolicited traffic is unknown. This brittleness may be accepted in
fallback due to lack of support on the server side.
Fallback addresses needs to be provided in their own transport
specification using a specifier that do not include the "D-ICE" lower
layer transport. Instead the selected protocol, e.g. UDP needs to
be explicitly or implictly indicated. Secondly the selected default
candidate needs to be included in the SETUP request. If this
candidate is server reflexive or relayed the aspect of keep-alive
needs to be ensured.
9. IANA Considerations
This document request registration in a number of registries, both
for RTSP and SDP.
9.1. RTSP Feature Tags
This document request that one RTSP 2.0 feature tags are registered
in the "RTSP 2.0 Feature-tags" registry:
Goldberg, et al. Expires November 8, 2012 [Page 25]
Internet-Draft A Media NAT Traversal mechanism for RTSP May 2012
setup.ice-d-m See Section 4.4. This feature tag applies to clients,
servers and proxies.
9.2. Transport Protocol Specifications
This document needs to register a number of transport protocol
combinations are registered in RTSP 2.0's "Transport Protocol
Specifications" registry.
"RTP/AVP/D-ICE" RTP using the AVP profile over an ICE established
datagram flow.
"RTP/AVPF/D-ICE" RTP using the AVPF profile over an ICE established
datagram flow.
"RTP/SAVP/D-ICE" RTP using the SAVP profile over an ICE established
datagram flow.
"RTP/SAVPF/D-ICE" RTP using the SAVPF profile over an ICE
established datagram flow.
9.3. RTSP Transport Parameters
This document requests that 3 transport parameters are registered in
RTSP 2.0's "Transport Parameters":
"candidates": Listing the properties of one or more ICE candidate.
See Section Section 4.2.
"ICE-Password": The ICE password used to authenticate the STUN
binding request in the ICE connectivity checks. See Section
Section 4.3.
"ICE-ufrag": The ICE username fragment used to authenticate the STUN
binding requests in the ICE connectivity checks. See Section
Section 4.3.
9.4. RTSP Status Codes
This document requests that 2 assignments are done in the "RTSP 2.0
Status Codes" registry. The suggested values are:
150: See Section Section 4.5.1.
480: See Section Section 4.5.2.
Goldberg, et al. Expires November 8, 2012 [Page 26]
Internet-Draft A Media NAT Traversal mechanism for RTSP May 2012
9.5. Notify-Reason value
This document requests that one assignment is done in the RTSP 2.0
Notify-Reason header value registry. The defined value is:
ice-restart: Server notifying the client about the need for an ICE
restart. See section Section 4.6.
9.6. SDP Attribute
The registration of one SDP attribute is requested:
SDP Attribute ("att-field"):
Attribute name: rtsp-ice-d-m
Long form: ICE for RTSP datagram media NAT traversal
Type of name: att-field
Type of attribute: Session level only
Subject to charset: No
Purpose: RFC XXXX
Reference: RFC XXXX
Values: No values defined.
Contact: Magnus Westerlund
E-mail: magnus.westerlund@ericsson.com
phone: +46 10 714 82 87
10. Security Considerations
ICE [RFC5245] and ICE TCP [RFC6544] provides an extensive discussion
on security considerations which applies here as well.
10.1. ICE and RTSP
A long-standing risk with transmitting a packet stream over UDP is
that the host may not be interested in receiving the stream. On
today's Internet many hosts are behind NATs or operate host firewalls
which do not respond to unsolicited packets with an ICMP port
unreachable error. Thus, an attacker can construct RTSP SETUP
requests with a victim's IP address and cause a flood of media
packets to be sent to a victim. The addition of ICE, as described in
this document, provides protection from the attack described above.
By performing the ICE connectivity check, the media server receives
confirmation that the RTSP client wants the media. While this
protection could also be implemented by requiring the IP addresses in
the SDP match the IP address of the RTSP signaling packet, such a
mechanism does not protect other hosts with the same IP address (such
as behind the same NAT), and such a mechanism would prohibit
separating the RTSP controller from the media playout device (e.g.,
Goldberg, et al. Expires November 8, 2012 [Page 27]
Internet-Draft A Media NAT Traversal mechanism for RTSP May 2012
an IP-enabled remote control and an IP-enabled television), it also
forces RTSP proxies to relay the media streams through them, even if
they only are signalling proxies.
To protect against the attacks in ICE based on signalling information
RTSP signalling should be protected using TLS to prevent evesdropping
and modification of information.
The STUN amplification attack described in Section 18.5.2 in ICE
needs consideration. For servers that are able to run according to
the high-reachability option have good mitigation against this attack
as it only sends its connectivity checks towards an address and port
pair it has received an incomming connectivity check from. Thus
requiring the capability to spoof source addresses in addition to
signal the RTSP server a set of ICE candidates. Independently an ICE
agent needs to implement the mitigation to reduce the volume of the
amplification attack as described in the ICE specification.
11. Acknowledgements
The authors would like to thank Remi Denis-Courmont for suggesting
the method of integrating ICE in RTSP signalling, Dan Wing for help
with the security section and numerous other issues.
12. References
12.1. Normative References
[I-D.ietf-mmusic-rfc2326bis]
Schulzrinne, H., Rao, A., Lanphier, R., Westerlund, M.,
and M. Stiemerling, "Real Time Streaming Protocol 2.0
(RTSP)", draft-ietf-mmusic-rfc2326bis-29 (work in
progress), March 2012.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC4566] Handley, M., Jacobson, V., and C. Perkins, "SDP: Session
Description Protocol", RFC 4566, July 2006.
[RFC5234] Crocker, D. and P. Overell, "Augmented BNF for Syntax
Specifications: ABNF", STD 68, RFC 5234, January 2008.
[RFC5245] Rosenberg, J., "Interactive Connectivity Establishment
(ICE): A Protocol for Network Address Translator (NAT)
Traversal for Offer/Answer Protocols", RFC 5245,
Goldberg, et al. Expires November 8, 2012 [Page 28]
Internet-Draft A Media NAT Traversal mechanism for RTSP May 2012
April 2010.
[RFC5389] Rosenberg, J., Mahy, R., Matthews, P., and D. Wing,
"Session Traversal Utilities for NAT (STUN)", RFC 5389,
October 2008.
[RFC5761] Perkins, C. and M. Westerlund, "Multiplexing RTP Data and
Control Packets on a Single Port", RFC 5761, April 2010.
[RFC6544] Rosenberg, J., Keranen, A., Lowekamp, B., and A. Roach,
"TCP Candidates with Interactive Connectivity
Establishment (ICE)", RFC 6544, March 2012.
12.2. Informative References
[I-D.ietf-mmusic-rtsp-nat-evaluation]
Westerlund, M. and T. Zeng, "The Evaluation of Different
Network Addres Translator (NAT) Traversal Techniques for
Media Controlled by Real-time Streaming Protocol (RTSP)",
draft-ietf-mmusic-rtsp-nat-evaluation-04 (work in
progress), October 2011.
[RFC2326] Schulzrinne, H., Rao, A., and R. Lanphier, "Real Time
Streaming Protocol (RTSP)", RFC 2326, April 1998.
[RFC3022] Srisuresh, P. and K. Egevang, "Traditional IP Network
Address Translator (Traditional NAT)", RFC 3022,
January 2001.
[RFC3261] Rosenberg, J., Schulzrinne, H., Camarillo, G., Johnston,
A., Peterson, J., Sparks, R., Handley, M., and E.
Schooler, "SIP: Session Initiation Protocol", RFC 3261,
June 2002.
[RFC3264] Rosenberg, J. and H. Schulzrinne, "An Offer/Answer Model
with Session Description Protocol (SDP)", RFC 3264,
June 2002.
[RFC3489] Rosenberg, J., Weinberger, J., Huitema, C., and R. Mahy,
"STUN - Simple Traversal of User Datagram Protocol (UDP)
Through Network Address Translators (NATs)", RFC 3489,
March 2003.
[RFC4340] Kohler, E., Handley, M., and S. Floyd, "Datagram
Congestion Control Protocol (DCCP)", RFC 4340, March 2006.
Goldberg, et al. Expires November 8, 2012 [Page 29]
Internet-Draft A Media NAT Traversal mechanism for RTSP May 2012
Authors' Addresses
Jeff Goldberg
Cisco
11 New Square, Bedfont Lakes
Feltham,, Middx TW14 8HA
United Kingdom
Phone: +44 20 8824 1000
Fax:
Email: jgoldber@cisco.com
URI:
Magnus Westerlund
Ericsson
Torshamsgatan 23
Stockholm, SE-164 80
Sweden
Phone: +46 8 719 0000
Fax:
Email: magnus.westerlund@ericsson.com
URI:
Thomas Zeng
Nextwave Wireless, Inc.
12670 High Bluff Drive
San Diego, CA 92130
USA
Phone: +1 858 480 3100
Fax:
Email: thomas.zeng@gmail.com
URI:
Goldberg, et al. Expires November 8, 2012 [Page 30]