Network Working Group I. Minei, Ed.
Internet-Draft Juniper Networks
Intended status: Standards Track IJ. Wijnands, Ed.
Expires: February 5, 2012 Cisco Systems, Inc.
K. Kompella
Juniper Networks
B. Thomas
August 4, 2011
Label Distribution Protocol Extensions for Point-to-Multipoint and
Multipoint-to-Multipoint Label Switched Paths
draft-ietf-mpls-ldp-p2mp-15
Abstract
This document describes extensions to the Label Distribution Protocol
for the setup of Point-to-Multipoint and Multipoint-to-Multipoint
Label Switched Paths in Multi-Protocol Label Switching networks.
These extensions are also referred to as Multipoint LDP. Multipoint
LDP constructs the P2MP or MP2MP Label Switched Paths without
interacting with or relying upon any other multicast tree
construction protocol. Protocol elements and procedures for this
solution are described for building such Label Switched Paths in a
receiver-initiated manner. There can be various applications for
Multipoint Label Switched Paths, for example IP multicast or support
for multicast in BGP/MPLS L3VPNs. Specification of how such
applications can use a LDP signaled Multipoint Label Switched Path is
outside the scope of this document.
Status of this Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on February 5, 2012.
Copyright Notice
Minei & Wijnands Expires February 5, 2012 [Page 1]
Internet-Draft P2MP and MP2MP LSP Setup with LDP August 2011
Copyright (c) 2011 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
This document may contain material from IETF Documents or IETF
Contributions published or made publicly available before November
10, 2008. The person(s) controlling the copyright in some of this
material may not have granted the IETF Trust the right to allow
modifications of such material outside the IETF Standards Process.
Without obtaining an adequate license from the person(s) controlling
the copyright in such materials, this document may not be modified
outside the IETF Standards Process, and derivative works of it may
not be created outside the IETF Standards Process, except to format
it for publication as an RFC or to translate it into languages other
than English.
Minei & Wijnands Expires February 5, 2012 [Page 2]
Internet-Draft P2MP and MP2MP LSP Setup with LDP August 2011
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1. Conventions used in this document . . . . . . . . . . . . 5
1.2. Terminology . . . . . . . . . . . . . . . . . . . . . . . 5
2. Setting up P2MP LSPs with LDP . . . . . . . . . . . . . . . . 6
2.1. Support for P2MP LSP setup with LDP . . . . . . . . . . . 7
2.2. The P2MP FEC Element . . . . . . . . . . . . . . . . . . . 7
2.3. The LDP MP Opaque Value Element . . . . . . . . . . . . . 9
2.3.1. The Generic LSP Identifier . . . . . . . . . . . . . . 10
2.4. Using the P2MP FEC Element . . . . . . . . . . . . . . . . 11
2.4.1. Label Mapping . . . . . . . . . . . . . . . . . . . . 11
2.4.2. Label Withdraw . . . . . . . . . . . . . . . . . . . . 13
2.4.3. Upstream LSR change . . . . . . . . . . . . . . . . . 14
3. Setting up MP2MP LSPs with LDP . . . . . . . . . . . . . . . . 15
3.1. Support for MP2MP LSP setup with LDP . . . . . . . . . . . 15
3.2. The MP2MP downstream and upstream FEC Elements. . . . . . 16
3.3. Using the MP2MP FEC Elements . . . . . . . . . . . . . . . 16
3.3.1. MP2MP Label Mapping . . . . . . . . . . . . . . . . . 18
3.3.2. MP2MP Label Withdraw . . . . . . . . . . . . . . . . . 21
3.3.3. MP2MP Upstream LSR change . . . . . . . . . . . . . . 22
4. Micro-loops in MP LSPs . . . . . . . . . . . . . . . . . . . . 22
5. The LDP MP Status TLV . . . . . . . . . . . . . . . . . . . . 22
5.1. The LDP MP Status Value Element . . . . . . . . . . . . . 23
5.2. LDP Messages containing LDP MP Status messages . . . . . . 24
5.2.1. LDP MP Status sent in LDP notification messages . . . 24
5.2.2. LDP MP Status TLV in Label Mapping Message . . . . . . 24
6. Upstream label allocation on a LAN . . . . . . . . . . . . . . 25
6.1. LDP Multipoint-to-Multipoint on a LAN . . . . . . . . . . 25
6.1.1. MP2MP downstream forwarding . . . . . . . . . . . . . 26
6.1.2. MP2MP upstream forwarding . . . . . . . . . . . . . . 26
7. Root node redundancy . . . . . . . . . . . . . . . . . . . . . 26
7.1. Root node redundancy - procedures for P2MP LSPs . . . . . 27
7.2. Root node redundancy - procedures for MP2MP LSPs . . . . . 27
8. Make Before Break (MBB) . . . . . . . . . . . . . . . . . . . 28
8.1. MBB overview . . . . . . . . . . . . . . . . . . . . . . . 28
8.2. The MBB Status code . . . . . . . . . . . . . . . . . . . 29
8.3. The MBB capability . . . . . . . . . . . . . . . . . . . . 30
8.4. The MBB procedures . . . . . . . . . . . . . . . . . . . . 30
8.4.1. Terminology . . . . . . . . . . . . . . . . . . . . . 30
8.4.2. Accepting elements . . . . . . . . . . . . . . . . . . 31
8.4.3. Procedures for upstream LSR change . . . . . . . . . . 31
8.4.4. Receiving a Label Mapping with MBB status code . . . . 32
8.4.5. Receiving a Notification with MBB status code . . . . 32
8.4.6. Node operation for MP2MP LSPs . . . . . . . . . . . . 33
9. Typed Wildcard for mLDP FEC Element . . . . . . . . . . . . . 33
10. Security Considerations . . . . . . . . . . . . . . . . . . . 33
11. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 34
Minei & Wijnands Expires February 5, 2012 [Page 3]
Internet-Draft P2MP and MP2MP LSP Setup with LDP August 2011
12. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 35
13. Contributing authors . . . . . . . . . . . . . . . . . . . . . 35
14. References . . . . . . . . . . . . . . . . . . . . . . . . . . 37
14.1. Normative References . . . . . . . . . . . . . . . . . . . 37
14.2. Informative References . . . . . . . . . . . . . . . . . . 38
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 38
Minei & Wijnands Expires February 5, 2012 [Page 4]
Internet-Draft P2MP and MP2MP LSP Setup with LDP August 2011
1. Introduction
The LDP protocol is described in [RFC5036]. It defines mechanisms
for setting up Point-to-Point (P2P) and Multipoint-to-Point (MP2P)
LSPs in the network. This document describes extensions to LDP for
setting up Point-to-Multipoint (P2MP) and Multipoint-to-Multipoint
(MP2MP) LSPs. These are collectively referred to as multipoint LSPs
(MP LSPs). A P2MP LSP allows traffic from a single root (or ingress)
node to be delivered to a number of leaf (or egress) nodes. A MP2MP
LSP allows traffic from multiple ingress nodes to be delivered to
multiple egress nodes. Only a single copy of the packet will be sent
to a LDP neighbor traversed by the MP LSP (see note at end of
Section 2.4.1). This is accomplished without the use of a multicast
protocol in the network. There can be several MP LSPs rooted at a
given ingress node, each with its own identifier.
The solution assumes that the leaf nodes of the MP LSP know the root
node and identifier of the MP LSP to which they belong. The
mechanisms for the distribution of this information are outside the
scope of this document. The specification of how an application can
use a MP LSP signaled by LDP is also outside the scope of this
document.
Related documents that may be of interest include
[I-D.ietf-mpls-mp-ldp-reqs], [I-D.ietf-l3vpn-2547bis-mcast] and
[RFC4875].
1.1. Conventions used in this document
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
1.2. Terminology
Some of the following terminology is taken from
[I-D.ietf-mpls-mp-ldp-reqs].
mLDP: Multipoint extensions for LDP.
P2P LSP: An LSP that has one Ingress LSR and one Egress LSR.
P2MP LSP: An LSP that has one Ingress LSR and one or more Egress
LSRs.
Minei & Wijnands Expires February 5, 2012 [Page 5]
Internet-Draft P2MP and MP2MP LSP Setup with LDP August 2011
MP2P LSP: An LSP that has one or more Ingress LSRs and one unique
Egress LSR.
MP2MP LSP: An LSP with a distinguished root node that connects a set
of nodes, such that traffic sent by any node in the LSP is
delivered to all others.
MP LSP: A multipoint LSP, either a P2MP or an MP2MP LSP.
Ingress LSR: An ingress LSR for a particular LSP is an LSR that can
send a data packet along the LSP. MP2MP LSPs can have multiple
ingress LSRs, P2MP LSPs have just one, and that node is often
referred to as the "root node".
Egress LSR: An egress LSR for a particular LSP is an LSR that can
remove a data packet from that LSP for further processing. P2P
and MP2P LSPs have only a single egress node, but P2MP and MP2MP
LSPs can have multiple egress nodes.
Transit LSR: An LSR that has reachability to the root of the MP LSP
via a directly connected upstream LSR and one or more directly
connected downstream LSRs.
Bud LSR: An LSR that is an egress but also has one or more directly
connected downstream LSRs.
Leaf node: A Leaf node can be either an Egress or Bud LSR when
referred in the context of a P2MP LSP. In the context of a MP2MP
LSP, a leaf is both Ingress and Egress for the same MP2MP LSP and
can also be a Bud LSR.
CRC32: This contains a Cyclic Redundancy Check value of the
uncompressed data in network byte order computed according to
CRC-32 algorithm used in the ISO 3309 standard and in section
8.1.1.6.2 of ITU-T recommendation V.42.
2. Setting up P2MP LSPs with LDP
A P2MP LSP consists of a single root node, zero or more transit nodes
and one or more leaf nodes. Leaf nodes initiate P2MP LSP setup and
tear-down. Leaf nodes also install forwarding state to deliver the
traffic received on a P2MP LSP to wherever it needs to go; how this
is done is outside the scope of this document. Transit nodes install
MPLS forwarding state and propagate the P2MP LSP setup (and tear-
down) toward the root. The root node installs forwarding state to
map traffic into the P2MP LSP; how the root node determines which
traffic should go over the P2MP LSP is outside the scope of this
Minei & Wijnands Expires February 5, 2012 [Page 6]
Internet-Draft P2MP and MP2MP LSP Setup with LDP August 2011
document.
2.1. Support for P2MP LSP setup with LDP
Support for the setup of P2MP LSPs is advertised using LDP
capabilities as defined in [RFC5561]. An implementation supporting
the P2MP procedures specified in this document MUST implement the
procedures for Capability Parameters in Initialization Messages.
A new Capability Parameter TLV is defined, the P2MP Capability.
Following is the format of the P2MP Capability Parameter.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|1|0| P2MP Capability (TBD IANA)| Length (= 1) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|S| Reserved |
+-+-+-+-+-+-+-+-+
S: As specified in [RFC5561]
The P2MP Capability TLV MUST be advertised in the LDP Initialization
Message. Advertisement of the P2MP Capability indicates support of
the procedures for P2MP LSP setup detailed in this document. If the
peer has not advertised the corresponding capability, then label
messages using the P2MP FEC Element SHOULD NOT be sent to the peer.
2.2. The P2MP FEC Element
For the setup of a P2MP LSP with LDP, we define one new protocol
entity, the P2MP FEC Element to be used as a FEC Element in the FEC
TLV. Note that the P2MP FEC Element does not necessarily identify
the traffic that must be mapped to the LSP, so from that point of
view, the use of the term FEC is a misnomer. The description of the
P2MP FEC Element follows.
The P2MP FEC Element consists of the address of the root of the P2MP
LSP and an opaque value. The opaque value consists of one or more
LDP MP Opaque Value Elements. The opaque value is unique within the
context of the root node. The combination of (Root Node Address
type, Root Node Address, Opaque Value) uniquely identifies a P2MP LSP
within the MPLS network.
Minei & Wijnands Expires February 5, 2012 [Page 7]
Internet-Draft P2MP and MP2MP LSP Setup with LDP August 2011
The P2MP FEC Element is encoded as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|P2MP Type (TBD)| Address Family | Address Length|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
~ Root Node Address ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Opaque Length | Opaque Value ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ +
~ ~
| |
| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type: The type of the P2MP FEC Element is to be assigned by IANA.
Address Family: Two octet quantity containing a value from IANA's
"Address Family Numbers" registry that encodes the address family
for the Root LSR Address.
Address Length: Length of the Root LSR Address in octets.
Root Node Address: A host address encoded according to the Address
Family field.
Opaque Length: The length of the Opaque Value, in octets.
Opaque Value: One or more MP Opaque Value elements, uniquely
identifying the P2MP LSP in the context of the Root Node. This is
described in the next section.
If the Address Family is IPv4, the Address Length MUST be 4; if the
Address Family is IPv6, the Address Length MUST be 16. No other
Address Lengths are defined at present.
If the Address Length doesn't match the defined length for the
Address Family, the receiver SHOULD abort processing the message
containing the FEC Element, and send an "Unknown FEC" Notification
Minei & Wijnands Expires February 5, 2012 [Page 8]
Internet-Draft P2MP and MP2MP LSP Setup with LDP August 2011
message to its LDP peer signaling an error.
If a FEC TLV contains a P2MP FEC Element, the P2MP FEC Element MUST
be the only FEC Element in the FEC TLV.
2.3. The LDP MP Opaque Value Element
The LDP MP Opaque Value Element is used in the P2MP and MP2MP FEC
Elements defined in subsequent sections. It carries information that
is meaningful to Ingress LSRs and Leaf LSRs, but need not be
interpreted by Transit LSRs.
The LDP MP Opaque Value Element basic type is encoded as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type < 255 | Length | Value ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |
~ ~
| |
| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type: The Type of the LDP MP Opaque Value Element. IANA maintains a
registry of basic types (see Section 11).
Length: The length of the Value field, in octets.
Value: String of Length octets, to be interpreted as specified by
the Type field.
Minei & Wijnands Expires February 5, 2012 [Page 9]
Internet-Draft P2MP and MP2MP LSP Setup with LDP August 2011
The LDP MP Opaque Value Element extended type is encoded as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = 255 | Extended Type | Length (high) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-|
| Length (low) | Value |
+-+-+-+-+-+-+-+-+ |
~ ~
| |
| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type: Type = 255.
Extended Type: The Extended Type of the LDP MP Opaque Value Element.
IANA maintains a registry of extended types (see Section 11).
Length: The length of the Value field, in octets.
Value: String of Length octets, to be interpreted as specified by
the Type field.
2.3.1. The Generic LSP Identifier
The generic LSP identifier is a type of Opaque Value Element basic
type encoded as follows:
Type: 1 (to be assigned by IANA)
Length: 4
Value: A 32bit integer, unique in the context of the root, as
identified by the root's address.
This type of Opaque Value Element is recommended when mapping of
traffic to LSPs is non-algorithmic, and done by means outside LDP.
Minei & Wijnands Expires February 5, 2012 [Page 10]
Internet-Draft P2MP and MP2MP LSP Setup with LDP August 2011
2.4. Using the P2MP FEC Element
This section defines the rules for the processing and propagation of
the P2MP FEC Element. The following notation is used in the
processing rules:
1. P2MP FEC Element <X, Y>: a FEC Element with Root Node Address X
and Opaque Value Y.
2. P2MP Label Mapping <X, Y, L>: a Label Mapping message with a FEC
TLV with a single P2MP FEC Element <X, Y> and Label TLV with
label L. Label L MUST be allocated from the per-platform label
space (see [RFC3031] section 3.14) of the LSR sending the Label
Mapping Message. The use of the interface label space is outside
the scope of this document.
3. P2MP Label Withdraw <X, Y, L>: a Label Withdraw message with a
FEC TLV with a single P2MP FEC Element <X, Y> and Label TLV with
label L.
4. P2MP LSP <X, Y> (or simply <X, Y>): a P2MP LSP with Root Node
Address X and Opaque Value Y.
5. The notation L' -> {<I1, L1> <I2, L2> ..., <In, Ln>} on LSR X
means that on receiving a packet with label L', X makes n copies
of the packet. For copy i of the packet, X swaps L' with Li and
sends it out over interface Ii.
The procedures below are organized by the role which the node plays
in the P2MP LSP. Node Z knows that it is a leaf node by a discovery
process which is outside the scope of this document. During the
course of protocol operation, the root node recognizes its role
because it owns the Root Node Address. A transit node is any node
(other than the root node) that receives a P2MP Label Mapping message
(i.e., one that has leaf nodes downstream of it).
Note that a transit node (and indeed the root node) may also be a
leaf node.
2.4.1. Label Mapping
The remainder of This section specifies the procedures for
originating P2MP Label Mapping messages and for processing received
P2MP Label Mapping messages for a particular LSP. The procedures for
a particular LSR depend upon the role that LSR plays in the LSP
Minei & Wijnands Expires February 5, 2012 [Page 11]
Internet-Draft P2MP and MP2MP LSP Setup with LDP August 2011
(ingress, transit, or egress).
All labels discussed here are downstream-assigned [RFC5332] except
those which are assigned using the procedures of Section 6.
2.4.1.1. Determining one's 'upstream LSR'
Each node that is either an Leaf or Transit LSR of MP LSP needs to
use the procedures below to select an upstream LSR. A node Z that
wants to join a MP LSP <X, Y> determines the LDP peer U which is Z's
next-hop on the best path from Z to the root node X. If there is more
than one such LDP peer, only one of them is picked. U is Z's
"Upstream LSR" for <X, Y>.
When there are several candidate upstream LSRs, the LSR MUST select
one upstream LSR. The algorithm used for the LSR selection is a
local matter. If the LSR selection is done over a LAN interface and
the Section 6 procedures are applied, the following procedure SHOULD
be applied to ensure that the same upstream LSR is elected among a
set of candidate receivers on that LAN.
1. The candidate upstream LSRs are numbered from lower to higher IP
address
2. The following hash is performed: H = (CRC32(Opaque Value)) modulo
N, where N is the number of upstream LSRs. The 'Opaque Value' is
the field identified in the FEC Element right after 'Opaque
Length'. The 'Opaque Length' indicates the size of the Opaque
Value used in this calculation.
3. The selected upstream LSR U is the LSR that has the number H.
This procedure will ensure that there is a single forwarder over the
LAN for a particular LSP.
2.4.1.2. Determining the forwarding interface to an LSR
Suppose LSR U receives a MP Label Mapping message from a downstream
LSR D, specifying label L. Suppose further that U is connected to D
over several LDP enabled interfaces or RSVP-TE Tunnel interfaces. If
U needs to transmit to D a data packet whose top label is L, U is
free to transmit the packet on any of those interfaces. The
algorithm it uses to choose a particular interface and next-hop for a
particular such packet is a local matter. For completeness the
following procedure MAY be used. LSR U may do a lookup in the
unicast routing table to find the best interface and next-hop to
reach LSR D. If the next-hop and interface are also advertised by LSR
D via the LDP session it can be used to transmit the packet to LSR D.
Minei & Wijnands Expires February 5, 2012 [Page 12]
Internet-Draft P2MP and MP2MP LSP Setup with LDP August 2011
2.4.1.3. Leaf Operation
A leaf node Z of P2MP LSP <X, Y> determines its upstream LSR U for
<X, Y> as per Section 2.4.1.1, allocates a label L, and sends a P2MP
Label Mapping <X, Y, L> to U.
2.4.1.4. Transit Node operation
Suppose a transit node Z receives a P2MP Label Mapping <X, Y, L> from
LSR T. Z checks whether it already has state for <X, Y>. If not, Z
determines its upstream LSR U for <X, Y> as per Section 2.4.1.1.
Using this Label Mapping to update the label forwarding table MUST
NOT be done as long as LSR T is equal to LSR U. If LSR U is different
from LSR T, Z will allocate a label L', and install state to swap L'
with L over interface I associated with LSR T and send a P2MP Label
Mapping <X, Y, L'> to LSR U. Interface I is determind via the
procedures in Section 2.4.1.2.
If Z already has state for <X, Y>, then Z does not send a Label
Mapping message for P2MP LSP <X, Y>. If LSR T is not equal to the
upstream LSR of <X, Y> and <I, L> does not already exist as
forwarding state, the forwarding state updated. Assuming its old
forwarding state was L'-> {<I1, L1> <I2, L2> ..., <In, Ln>}, its new
forwarding state becomes L'-> {<I1, L1> <I2, L2> ..., <In, Ln>, <I,
L>}. If the LSR T is equal to the installed upstream LSR, the Label
Mapping from LSR T MUST be retained and MUST NOT update the label
forwarding table.
2.4.1.5. Root Node Operation
Suppose the root node Z receives a P2MP Label Mapping <X, Y, L> from
LSR T. Z checks whether it already has forwarding state for <X, Y>.
If not, Z creates forwarding state to push label L onto the traffic
that Z wants to forward over the P2MP LSP (how this traffic is
determined is outside the scope of this document).
If Z already has forwarding state for <X, Y>, then Z adds "push label
L, send over interface I" to the nexthop, where I is the interface
associated with LSR T and determined via the procedures in
Section 2.4.1.2.
2.4.2. Label Withdraw
The following section lists procedures for generating and processing
P2MP Label Withdraw messages for nodes that participate in a P2MP
LSP. An LSR should apply those procedures that apply to it, based on
its role in the P2MP LSP.
Minei & Wijnands Expires February 5, 2012 [Page 13]
Internet-Draft P2MP and MP2MP LSP Setup with LDP August 2011
2.4.2.1. Leaf Operation
If a leaf node Z discovers that it has no downstream neighbors in
that LSP, and that it has no need to be an egress LSR for that LSP
(by means outside the scope of this document), then it SHOULD send a
Label Withdraw <X, Y, L> to its upstream LSR U for <X, Y>, where L is
the label it had previously advertised to U for <X, Y>.
2.4.2.2. Transit Node Operation
If a transit node Z receives a Label Withdraw message <X, Y, L> from
a node W, it deletes label L from its forwarding state, and sends a
Label Release message with label L to W.
If deleting L from Z's forwarding state for P2MP LSP <X, Y> results
in no state remaining for <X, Y>, then Z propagates the Label
Withdraw for <X, Y>, to its upstream T, by sending a Label Withdraw
<X, Y, L1> where L1 is the label Z had previously advertised to T for
<X, Y>.
2.4.2.3. Root Node Operation
The procedure when the root node of a P2MP LSP receives a Label
Withdraw message are the same as for transit nodes, except that it
would not propagate the Label Withdraw upstream (as it has no
upstream).
2.4.3. Upstream LSR change
Suppose that for a given node Z participating in a P2MP LSP <X, Y>,
the upstream LSR changes from U to U' as per Section 2.4.1.1. Z MUST
update its forwarding state as follows. It allocates a new label,
L', for <X, Y>. The forwarding state for L' is copied from the
forwarding state for L, with one exception: if U' was present in the
forwarding state of L, it MUST NOT be installed in the forwarding
state of L'. Then the forwarding state for L is deleted and the
forwarding state for L' is installed. In addition Z MUST send a
Label Mapping <X, Y, L'> to U' and send a Label Withdraw <X, Y, L> to
U. Note, if there was a downstream mapping from U that was not
installed in the forwarding due to Section 2.4.1.4 it can now be
installed.
While changing the upstream LSR the following must be taken into
consideration. If L' is added before L is removed, there is a
potential risk of packet duplication, and/or the creation of a
transient dataplane forwarding loop. If L is removed before L' is
added, packet loss may result. Ideally the change from L to L' is
done atomically such that no packet loss or duplication occurs. If
Minei & Wijnands Expires February 5, 2012 [Page 14]
Internet-Draft P2MP and MP2MP LSP Setup with LDP August 2011
that is not possible, the RECOMMENDED default behavior is to remove L
before adding L'.
3. Setting up MP2MP LSPs with LDP
An MP2MP LSP is much like a P2MP LSP in that it consists of a single
root node, zero or more transit nodes and one or more leaf LSRs
acting equally as Ingress or Egress LSR. A leaf node participates in
the setup of an MP2MP LSP by establishing both a downstream LSP,
which is much like a P2MP LSP from the root, and an upstream LSP
which is used to send traffic toward the root and other leaf nodes.
Transit nodes support the setup by propagating the upstream and
downstream LSP setup toward the root and installing the necessary
MPLS forwarding state. The transmission of packets from the root
node of a MP2MP LSP to the receivers is identical to that for a P2MP
LSP. Traffic from a downstream node follows the upstream LSP toward
the root node and branches downward along the downstream LSP as
required to reach other leaf nodes. A packet that is received from a
downstream node MUST never be forwarded back out to that same node.
Mapping traffic to the MP2MP LSP may happen at any leaf node. How
that mapping is established is outside the scope of this document.
Due to how a MP2MP LSP is built a leaf LSR that is sending packets on
the MP2MP LSP does not receive its own packets. There is also no
additional mechanism needed on the root or transit LSR to match
upstream traffic to the downstream forwarding state. Packets that
are forwarded over a MP2MP LSP will not traverse a link more than
once, with the possible exception of LAN links (see Section 3.3.1),
if the procedures of [RFC5331] are not provided.
3.1. Support for MP2MP LSP setup with LDP
Support for the setup of MP2MP LSPs is advertised using LDP
capabilities as defined in [RFC5561]. An implementation supporting
the MP2MP procedures specified in this document MUST implement the
procedures for Capability Parameters in Initialization Messages.
A new Capability Parameter TLV is defined, the MP2MP Capability.
Following is the format of the MP2MP Capability Parameter.
Minei & Wijnands Expires February 5, 2012 [Page 15]
Internet-Draft P2MP and MP2MP LSP Setup with LDP August 2011
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|1|0| MP2MP Capability TBD IANA | Length (= 1) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|S| Reserved |
+-+-+-+-+-+-+-+-+
S: As specified in [RFC5561]
The MP2MP Capability TLV MUST be advertised in the LDP Initialization
Message. Advertisement of the MP2MP Capability indicates support of
the procedures for MP2MP LSP setup detailed in this document. If the
peer has not advertised the corresponding capability, then label
messages using the MP2MP upstream and downstream FEC Elements SHOULD
NOT be sent to the peer.
3.2. The MP2MP downstream and upstream FEC Elements.
For the setup of a MP2MP LSP with LDP we define 2 new protocol
entities, the MP2MP downstream FEC and upstream FEC Element. Both
elements will be used as FEC Elements in the FEC TLV. Note that the
MP2MP FEC Elements do not necessarily identify the traffic that must
be mapped to the LSP, so from that point of view, the use of the term
FEC is a misnomer. The description of the MP2MP FEC Elements follow.
The structure, encoding and error handling for the MP2MP downstream
and upstream FEC Elements are the same as for the P2MP FEC Element
described in Section 2.2. The difference is that two new FEC types
are used: MP2MP downstream type (TBD) and MP2MP upstream type (TBD).
If a FEC TLV contains an MP2MP FEC Element, the MP2MP FEC Element
MUST be the only FEC Element in the FEC TLV.
Note, except when using the procedures of [RFC5331], the MPLS labels
used are "downstream-assigned" [RFC5332], even if they are bound to
the "upstream FEC element".
3.3. Using the MP2MP FEC Elements
This section defines the rules for the processing and propagation of
the MP2MP FEC Elements. The following notation is used in the
processing rules:
1. MP2MP downstream LSP <X, Y> (or simply downstream <X, Y>): an
MP2MP LSP downstream path with root node address X and opaque
value Y.
Minei & Wijnands Expires February 5, 2012 [Page 16]
Internet-Draft P2MP and MP2MP LSP Setup with LDP August 2011
2. MP2MP upstream LSP <X, Y, D> (or simply upstream <X, Y, D>): a
MP2MP LSP upstream path for downstream node D with root node
address X and opaque value Y.
3. MP2MP downstream FEC Element <X, Y>: a FEC Element with root
node address X and opaque value Y used for a downstream MP2MP
LSP.
4. MP2MP upstream FEC Element <X, Y>: a FEC Element with root node
address X and opaque value Y used for an upstream MP2MP LSP.
5. MP2MP-D Label Mapping <X, Y, L>: A Label Mapping message with a
FEC TLV with a single MP2MP downstream FEC Element <X, Y> and
label TLV with label L. Label L MUST be allocated from the per-
platform label space (see [RFC3031] section 3.14) of the LSR
sending the Label Mapping Message. The use of the interface
label space is outside the scope of this document.
6. MP2MP-U Label Mapping <X, Y, Lu>: A Label Mapping message with a
FEC TLV with a single MP2MP upstream FEC Element <X, Y> and
label TLV with label Lu. Label Lu MUST be allocated from the
per-platform label space (see [RFC3031] section 3.14) of the LSR
sending the Label Mapping Message. The use of the interface
label space is outside the scope of this document.
7. MP2MP-D Label Withdraw <X, Y, L>: a Label Withdraw message with
a FEC TLV with a single MP2MP downstream FEC Element <X, Y> and
label TLV with label L.
8. MP2MP-U Label Withdraw <X, Y, Lu>: a Label Withdraw message with
a FEC TLV with a single MP2MP upstream FEC Element <X, Y> and
label TLV with label Lu.
9. MP2MP-D Label Release <X, Y, L>: a Label Release message with a
FEC TLV with a single MP2MP downstream FEC Element <X, Y> and
label TLV with label L.
10. MP2MP-U Label Release <X, Y, Lu>: a Label Release message with a
FEC TLV with a single MP2MP upstream FEC Element <X, Y> and
label TLV with label Lu.
Minei & Wijnands Expires February 5, 2012 [Page 17]
Internet-Draft P2MP and MP2MP LSP Setup with LDP August 2011
The procedures below are organized by the role which the node plays
in the MP2MP LSP. Node Z knows that it is a leaf node by a discovery
process which is outside the scope of this document. During the
course of the protocol operation, the root node recognizes its role
because it owns the root node address. A transit node is any node
(other then the root node) that receives a MP2MP Label Mapping
message (i.e., one that has leaf nodes downstream of it).
Note that a transit node (and indeed the root node) may also be a
leaf node and the root node does not have to be an ingress LSR or
leaf of the MP2MP LSP.
3.3.1. MP2MP Label Mapping
The remainder of This section specifies the procedures for
originating MP2MP Label Mapping messages and for processing received
MP2MP Label Mapping messages for a particular LSP. The procedures
for a particular LSR depend upon the role that LSR plays in the LSP
(ingress, transit, or egress).
All labels discussed here are downstream-assigned [RFC5332] except
those which are assigned using the procedures of Section 6.
3.3.1.1. Determining one's upstream MP2MP LSR
Determining the upstream LDP peer U for a MP2MP LSP <X, Y> follows
the procedure for a P2MP LSP described in Section 2.4.1.1.
3.3.1.2. Determining one's downstream MP2MP LSR
A LDP peer U which receives a MP2MP-D Label Mapping from a LDP peer D
will treat D as downstream MP2MP LSR.
3.3.1.3. Installing the upstream path of a MP2MP LSP
There are two methods for installing the upstream path of a MP2MP LSP
to a downstream neighbor.
1. We can install the upstream MP2MP path (to a downstream neighbor)
based on receiving a MP2MP-D Label Mapping from the downstream
neighbor. This will install the upstream path on a per hop by
hop basis.
2. We install the upstream MP2MP path (to a downstream neighbor)
based on receiving a MP2MP-U Label Mapping from the upstream
neighbor. An LSR does not need to wait for the MP2MP-U Label
Mapping if it is the root of the MP2MP LSP or already has
Minei & Wijnands Expires February 5, 2012 [Page 18]
Internet-Draft P2MP and MP2MP LSP Setup with LDP August 2011
received an MP2MP-U Label Mapping from the upstream neighbor. We
call this method ordered mode. The typical result of this mode
is that the downstream path of the MP2MP is built hop by hop
towards the root. Once the root is reached, the root node will
trigger a MP2MP-U Label Mapping to the downstream neighbor(s).
For setting up the upstream path of a MP2MP LSP ordered mode SHOULD
be used. Due to ordered mode the upstream path of the MP2MP LSP is
installed at the leaf node once the path to the root is completed.
The advantage is that when a leaf starts sending immediately after
the upstream path is installed, packets are able to reach the root
node without being dropped due to an incomplete LSP. Method 1 is not
able to guarantee that the upstream path is completed before the leaf
starts sending.
3.3.1.4. MP2MP leaf node operation
A leaf node Z of a MP2MP LSP <X, Y> determines its upstream LSR U for
<X, Y> as per Section 3.3.1.1, allocates a label L, and sends a
MP2MP-D Label Mapping <X, Y, L> to U.
Leaf node Z expects an MP2MP-U Label Mapping <X, Y, Lu> from node U
in response to the MP2MP-D Label Mapping it sent to node U. Z checks
whether it already has forwarding state for upstream <X, Y>. If not,
Z creates forwarding state to push label Lu onto the traffic that Z
wants to forward over the MP2MP LSP. How it determines what traffic
to forward on this MP2MP LSP is outside the scope of this document.
3.3.1.5. MP2MP transit node operation
Suppose node Z receives a MP2MP-D Label Mapping <X, Y, L> from LSR D.
Z checks whether it has forwarding state for downstream <X, Y>. If
not, Z determines its upstream LSR U for <X, Y> as per
Section 3.3.1.1. Using this Label Mapping to update the label
forwarding table MUST NOT be done as long as LSR D is equal to LSR U.
If LSR U is different from LSR D, Z will allocate a label L' and
install downstream forwarding state to swap label L' with label L
over interface I associated with LSR D and send a MP2MP-D Label
Mapping <X, Y, L'> to U. Interface I is determined via the procedures
in Section 2.4.1.2.
If Z already has forwarding state for downstream <X, Y>, all that Z
needs to do in this case is check that LSR D is not equal to the
upstream LSR of <X, Y> and update its forwarding state. Assuming its
old forwarding state was L'-> {<I1, L1> <I2, L2> ..., <In, Ln>}, its
new forwarding state becomes L'-> {<I1, L1> <I2, L2> ..., <In, Ln>,
<I, L>}. If the LSR D is equal to the installed upstream LSR, the
Minei & Wijnands Expires February 5, 2012 [Page 19]
Internet-Draft P2MP and MP2MP LSP Setup with LDP August 2011
Label Mapping from LSR D MUST be retained and MUST NOT update the
label forwarding table.
Node Z checks if upstream LSR U already assigned a label Lu to <X,
Y>. If not, transit node Z waits until it receives a MP2MP-U Label
Mapping <X, Y, Lu> from LSR U. See Section 3.3.1.3. Once the MP2MP-U
Label Mapping is received from LSR U, node Z checks whether it
already has forwarding state upstream <X, Y, D>. If it does, then no
further action needs to happen. If it does not, it allocates a label
Lu' and creates a new label swap for Lu' with Label Lu over interface
Iu. Interface Iu is determined via the procedures in
Section 2.4.1.2. In addition, it also adds the label swap(s) from
the forwarding state downstream <X, Y>, omitting the swap on
interface I for node D. The swap on interface I for node D is omitted
to prevent packet originated by D to be forwarded back to D.
Node Z determines the downstream MP2MP LSR as per Section 3.3.1.2,
and sends a MP2MP-U Label Mapping <X, Y, Lu'> to node D.
3.3.1.6. MP2MP root node operation
3.3.1.6.1. Root node is also a leaf
Suppose root/leaf node Z receives a MP2MP-D Label Mapping <X, Y, L>
from node D. Z checks whether it already has forwarding state
downstream <X, Y>. If not, Z creates forwarding state for downstream
to push label L on traffic that Z wants to forward down the MP2MP
LSP. How it determines what traffic to forward on this MP2MP LSP is
outside the scope of this document. If Z already has forwarding
state for downstream <X, Y>, then Z will add the label push for L
over interface I to it. Interface I is determined via the procedures
in Section 2.4.1.2.
Node Z checks if it has forwarding state for upstream <X, Y, D> If
not, Z allocates a label Lu' and creates upstream forwarding state to
swap Lu' with the label swap(s) from the forwarding state downstream
<X, Y>, except the swap on interface I for node D. This allows
upstream traffic to go down the MP2MP to other node(s), except the
node from which the traffic was received. Node Z determines the
downstream MP2MP LSR as per section Section 3.3.1.2, and sends a
MP2MP-U Label Mapping <X, Y, Lu'> to node D. Since Z is the root of
the tree Z will not send a MP2MP-D Label Mapping and will not receive
a MP2MP-U Label Mapping.
3.3.1.6.2. Root node is not a leaf
Suppose the root node Z receives a MP2MP-D Label Mapping <X, Y, L>
from node D. Z checks whether it already has forwarding state for
Minei & Wijnands Expires February 5, 2012 [Page 20]
Internet-Draft P2MP and MP2MP LSP Setup with LDP August 2011
downstream <X, Y>. If not, Z creates downstream forwarding state and
installs a outgoing label L over interface I. Interface I is
determined via the procedures in Section 2.4.1.2. If Z already has
forwarding state for downstream <X, Y>, then Z will add label L over
interface I to the existing state.
Node Z checks if it has forwarding state for upstream <X, Y, D>. If
not, Z allocates a label Lu' and creates forwarding state to swap Lu'
with the label swap(s) from the forwarding state downstream <X, Y>,
except the swap for node D. This allows upstream traffic to go down
the MP2MP to other node(s), except the node is was received from.
Root node Z determines the downstream MP2MP LSR D as per
Section 3.3.1.2, and sends a MP2MP-U Label Mapping <X, Y, Lu'> to it.
Since Z is the root of the tree Z will not send a MP2MP-D Label
Mapping and will not receive a MP2MP-U Label Mapping.
3.3.2. MP2MP Label Withdraw
The following section lists procedures for generating and processing
MP2MP Label Withdraw messages for nodes that participate in a MP2MP
LSP. An LSR should apply those procedures that apply to it, based on
its role in the MP2MP LSP.
3.3.2.1. MP2MP leaf operation
If a leaf node Z discovers (by means outside the scope of this
document) that it has no downstream neighbors in that LSP, and that
it has no need to be an egress LSR for that LSP (by means outside the
scope of this document), then it SHOULD send a MP2MP-D Label Withdraw
<X, Y, L> to its upstream LSR U for <X, Y>, where L is the label it
had previously advertised to U for <X,Y>. Leaf node Z will also send
a unsolicited label release <X, Y, Lu> to U to indicate that the
upstream path is no longer used and that Label Lu can be removed.
Leaf node Z expects the upstream router U to respond by sending a
downstream label release for L.
3.3.2.2. MP2MP transit node operation
If a transit node Z receives a MP2MP-D Label Withdraw message <X, Y,
L> from node D, it deletes label L from its forwarding state
downstream <X, Y> and from all its upstream states for <X, Y>. Node
Z sends a MP2MP-D Label Release message with label L to D. Since node
D is no longer part of the downstream forwarding state, Z cleans up
the forwarding state upstream <X, Y, D>. There is no need to send an
MP2MP-U Label Withdraw <X, Y, Lu> to D because node D already removed
Lu and send a label release for Lu to Z.
Minei & Wijnands Expires February 5, 2012 [Page 21]
Internet-Draft P2MP and MP2MP LSP Setup with LDP August 2011
If deleting L from Z's forwarding state for downstream <X, Y> results
in no state remaining for <X, Y>, then Z propagates the MP2MP-D Label
Withdraw <X, Y, L> to its upstream node U for <X,Y> and will also
send a unsolicited MP2MP-U Label Release <X, Y, Lu> to U to indicate
that the upstream path is no longer used and that Label Lu can be
removed.
3.3.2.3. MP2MP root node operation
The procedure when the root node of a MP2MP LSP receives a MP2MP-D
Label Withdraw message is the same as for transit nodes, except that
the root node would not propagate the Label Withdraw upstream (as it
has no upstream).
3.3.3. MP2MP Upstream LSR change
The procedure for changing the upstream LSR is the same as documented
in Section 2.4.3, except it is applied to MP2MP FECs, using the
procedures described in Section 3.3.1 through Section 3.3.2.3.
4. Micro-loops in MP LSPs
Micro-loops created by the unicast routing protocol during
convergence may also effect mLDP MP LSPs. Since the tree building
logic in mLDP is based on unicast routing, a unicast routing loop may
also result in a micro-loop in the MP LSPs. Micro-loops that involve
2 directly connected routers don't create a loop in mLDP. mLDP is
able to prevent this inconsistency by never allowing an upstream LDP
neighbor to be added as a downstream LDP neighbor into the Label
Forwarding Table (LFT) for the same FEC. Micro-loops that involve
more than 2 LSRs are not prevented.
Micro-loops that involve more than 2 LSRs may create a micro-loop in
the downstream path of either a MP2MP LSP or P2MP LSP and the
upstream path of the MP2MP LSP. The loops are transient and will
disappear as soon as the unicast routing protocol converges and mLDP
has updated the forwarding state accordingly. Micro-loops that occur
in the upstream path of a MP2MP LSP may be detected by including LDP
path vector in the MP2MP-U Label Mapping messages. These procedures
are currently under investigation and are subjected to further study.
5. The LDP MP Status TLV
An LDP MP capable router MAY use an LDP MP Status TLV to indicate
additional status for a MP LSP to its remote peers. This includes
signaling to peers that are either upstream or downstream of the LDP
Minei & Wijnands Expires February 5, 2012 [Page 22]
Internet-Draft P2MP and MP2MP LSP Setup with LDP August 2011
MP capable router. The value of the LDP MP status TLV will remain
opaque to LDP and MAY encode one or more status elements.
The LDP MP Status TLV is encoded as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|1|0| LDP MP Status Type(TBD) | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Value |
~ ~
| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
LDP MP Status Type: The LDP MP Status Type to be assigned by IANA.
Length: Length of the LDP MP Status Value in octets.
Value: One or more LDP MP Status Value elements.
5.1. The LDP MP Status Value Element
The LDP MP Status Value Element that is included in the LDP MP Status
TLV Value has the following encoding.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Value ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |
~ ~
| |
| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type: The type of the LDP MP Status Value Element. IANA maintains a
registry of status value types (see Section 11).
Minei & Wijnands Expires February 5, 2012 [Page 23]
Internet-Draft P2MP and MP2MP LSP Setup with LDP August 2011
Length: The length of the Value field, in octets.
Value: String of Length octets, to be interpreted as specified by
the Type field.
5.2. LDP Messages containing LDP MP Status messages
The LDP MP Status TLV may appear either in a Label Mapping message or
a LDP Notification message.
5.2.1. LDP MP Status sent in LDP notification messages
An LDP MP status TLV sent in a notification message must be
accompanied with a Status TLV, as described in [RFC5036]. The
general format of the Notification Message with an LDP MP status TLV
is:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0| Notification (0x0001) | Message Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Message ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Status TLV |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| LDP MP Status TLV |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Optional LDP MP FEC TLV |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Optional Label TLV |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
The Status TLV status code is used to indicate that LDP MP status TLV
and any additional information follows in the Notification message's
"optional parameter" section. Depending on the actual contents of
the LDP MP status TLV, an LDP P2MP or MP2MP FEC TLV and Label TLV may
also be present to provide context to the LDP MP Status TLV. (NOTE:
Status Code is pending IANA assignment).
Since the notification does not refer to any particular message, the
Message Id and Message Type fields are set to 0.
5.2.2. LDP MP Status TLV in Label Mapping Message
An example of the Label Mapping Message defined in RFC3036 is shown
below to illustrate the message with an Optional LDP MP Status TLV
Minei & Wijnands Expires February 5, 2012 [Page 24]
Internet-Draft P2MP and MP2MP LSP Setup with LDP August 2011
present.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0| Label Mapping (0x0400) | Message Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Message ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| FEC TLV |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Label TLV |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Optional LDP MP Status TLV |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Additional Optional Parameters |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
6. Upstream label allocation on a LAN
On a LAN, the procedures so far discussed would require the upstream
LSR to send a copy of the packet to each receiver individually. If
there is more than one receiver on the LAN we don't take full benefit
of the multi-access capability of the network. We may optimize the
bandwidth consumption on the LAN and replication overhead on the
upstream LSR by using upstream label allocation [RFC5331].
Procedures on how to distribute upstream labels using LDP is
documented in [I-D.ietf-mpls-ldp-upstream].
6.1. LDP Multipoint-to-Multipoint on a LAN
The procedure to allocate a context label on a LAN is defined in
[RFC5331]. That procedure results in each LSR on a given LAN having
a context label which, on that LAN, can be used to identify itself
uniquely. Each LSR advertises its context label as an upstream-
assigned label, following the procedures of
[I-D.ietf-mpls-ldp-upstream]. Any LSR for which the LAN is a
downstream link on some P2MP or MP2MP LSP will allocate an upstream-
assigned label identifying that LSP. When the LSR forwards a packet
downstream on one of those LSPs, the packet's top label must be the
LSR's context label, and the packet's second label is the label
identifying the LSP. We will call the top label the "upstream LSR
label" and the second label the "LSP label".
Minei & Wijnands Expires February 5, 2012 [Page 25]
Internet-Draft P2MP and MP2MP LSP Setup with LDP August 2011
6.1.1. MP2MP downstream forwarding
The downstream path of a MP2MP LSP is much like a normal P2MP LSP, so
we will use the same procedures as defined in
[I-D.ietf-mpls-ldp-upstream]. A label request for a LSP label is
sent to the upstream LSR. The Label Mapping that is received from
the upstream LSR contains the LSP label for the MP2MP FEC and the
upstream LSR context label. The MP2MP downstream path (corresponding
to the LSP label) will be installed in the context specific
forwarding table corresponding to the upstream LSR label. Packets
sent by the upstream router can be forwarded downstream using this
forwarding state based on a two label lookup.
6.1.2. MP2MP upstream forwarding
A MP2MP LSP also has an upstream forwarding path. Upstream packets
need to be forwarded in the direction of the root and downstream on
any node on the LAN that has a downstream interface for the LSP. For
a given MP2MP LSP on a given LAN, exactly one LSR is considered to be
the upstream LSR. If an LSR on the LAN receives a packet from one of
its downstream interfaces for the LSP, and if it needs to forward the
packet onto the LAN, it ensures that the packet's top label is the
context label of the upstream LSR, and that its second label is the
LSP label that was assigned by the upstream LSR.
Other LSRs receiving the packet will not be able to tell whether the
packet really came from the upstream router, but that makes no
difference in the processing of the packet. The upstream LSR will
see its own upstream LSR in the label, and this will enable it to
determine that the packet is traveling upstream.
7. Root node redundancy
The root node is a single point of failure for an MP LSP, whether
this is P2MP or MP2MP. The problem is particularly severe for MP2MP
LSPs. In the case of MP2MP LSPs, all leaf nodes must use the same
root node to set up the MP2MP LSP, because otherwise the traffic
sourced by some leafs is not received by others. Because the root
node is the single point of failure for an MP LSP, we need a fast and
efficient mechanism to recover from a root node failure.
An MP LSP is uniquely identified in the network by the opaque value
and the root node address. It is likely that the root node for an MP
LSP is defined statically. The root node address may be configured
on each leaf statically or learned using a dynamic protocol. How
leafs learn about the root node is out of the scope of this document.
Minei & Wijnands Expires February 5, 2012 [Page 26]
Internet-Draft P2MP and MP2MP LSP Setup with LDP August 2011
Suppose that for the same opaque value we define two (or more) root
node addresses and we build a tree to each root using the same opaque
value. Effectively these will be treated as different MP LSPs in the
network. Once the trees are built, the procedures differ for P2MP
and MP2MP LSPs. The different procedures are explained in the
sections below.
7.1. Root node redundancy - procedures for P2MP LSPs
Since all leafs have set up P2MP LSPs to all the roots, they are
prepared to receive packets on either one of these LSPs. However,
only one of the roots should be forwarding traffic at any given time,
for the following reasons: 1) to achieve bandwidth savings in the
network and 2) to ensure that the receiving leafs don't receive
duplicate packets (since one cannot assume that the receiving leafs
are able to discard duplicates). How the roots determine which one
is the active sender is outside the scope of this document.
7.2. Root node redundancy - procedures for MP2MP LSPs
Since all leafs have set up an MP2MP LSP to each one of the root
nodes for this opaque value, a sending leaf may pick either of the
two (or more) MP2MP LSPs to forward a packet on. The leaf nodes
receive the packet on one of the MP2MP LSPs. The client of the MP2MP
LSP does not care on which MP2MP LSP the packet is received, as long
as they are for the same opaque value. The sending leaf MUST only
forward a packet on one MP2MP LSP at a given point in time. The
receiving leafs are unable to discard duplicate packets because they
accept on all LSPs. Using all the available MP2MP LSPs we can
implement redundancy using the following procedures.
A sending leaf selects a single root node out of the available roots
for a given opaque value. A good strategy MAY be to look at the
unicast routing table and select a root that is closest in terms of
the unicast metric. As soon as the root address of the active root
disappears from the unicast routing table (or becomes less
attractive) due to root node or link failure, the leaf can select a
new best root address and start forwarding to it directly. If
multiple root nodes have the same unicast metric, the highest root
node addresses MAY be selected, or per session load balancing MAY be
done over the root nodes.
All leafs participating in a MP2MP LSP MUST join to all the available
root nodes for a given opaque value. Since the sending leaf may pick
any MP2MP LSP, it must be prepared to receive on it.
The advantage of pre-building multiple MP2MP LSPs for a single opaque
value is that convergence from a root node failure happens as fast as
Minei & Wijnands Expires February 5, 2012 [Page 27]
Internet-Draft P2MP and MP2MP LSP Setup with LDP August 2011
the unicast routing protocol is able to notify. There is no need for
an additional protocol to advertise to the leaf nodes which root node
is the active root. The root selection is a local leaf policy that
does not need to be coordinated with other leafs. The disadvantage
of pre-building multiple MP2MP LSPs is that more label resources are
used, depending on how many root nodes are defined.
8. Make Before Break (MBB)
An LSR selects as its upstream LSR for a MP LSP the LSR that is its
next hop to the root of the LSP. When the best path to reach the
root changes the LSR must choose a new upstream LSR. Sections
Section 2.4.3 and Section 3.3.3 describe these procedures.
When the best path to the root changes the LSP may be broken
temporarily resulting in packet loss until the LSP "reconverges" to a
new upstream LSR. The goal of MBB when this happens is to keep the
duration of packet loss as short as possible. In addition, there are
scenarios where the best path from the LSR to the root changes but
the LSP continues to forward packets to the prevous next hop to the
root. That may occur when a link comes up or routing metrics change.
In such a case a new LSP should be established before the old LSP is
removed to limit the duration of packet loss. The procedures
described below deal with both scenarios in a way that an LSR does
not need to know which of the events described above caused its
upstream router for an MBB LSP to change.
The MBB procedures are an optional extension to the MP LSP building
procedures described in this draft. The procedures in this section
offer a make-before-break behavior, except in cases where the new
path is part of a transient routing loop involving more than 2 LSRs
(also see Section 4).
8.1. MBB overview
The MBB procedures use additional LDP signaling.
Suppose some event causes a downstream LSR-D to select a new upstream
LSR-U for FEC-A. The new LSR-U may already be forwarding packets for
FEC-A; that is, to downstream LSRs other than LSR-D. After LSR-U
receives a label for FEC-A from LSR-D, it will notify LSR-D when it
knows that the LSP for FEC-A has been established from the root to
itself. When LSR-D receives this MBB notification it will change its
next hop for the LSP root to LSR-U.
The assumption is that if LSR-U has received an MBB notification from
its upstream router for the FEC-A LSP and has installed forwarding
Minei & Wijnands Expires February 5, 2012 [Page 28]
Internet-Draft P2MP and MP2MP LSP Setup with LDP August 2011
state the LSP it is capable of forwarding packets on the LSP. At
that point LSR-U should signal LSR-D by means of an MBB notification
that it has become part of the tree identified by FEC-A and that
LSR-D should initiate its switchover to the LSP.
At LSR-U the LSP for FEC-A may be in 1 of 3 states.
1. There is no state for FEC-A.
2. State for FEC-A exists and LSR-U is waiting for MBB notification
that the LSP from the root to it exists.
3. State for FEC-A exists and the MBB notification has been received
or it is the Root node for FEC-A.
After LSR-U receives LSR-D's Label Mapping message for FEC-A LSR-U
MUST NOT reply with an MBB notification to LSR-D until its state for
the LSP is state #3 above. If the state of the LSP at LSR-U is state
#1 or #2, LSR-U should remember receipt of the Label Mapping message
from LSR-D while waiting for an MBB notification from its upstream
LSR for the LSP. When LSR-U receives the MBB notification from LSR-U
it transitions to LSP state #3 and sends an MBB notification to
LSR-D.
8.2. The MBB Status code
As noted in Section 8.1, the procedures to establish an MBB MP LSP
are different from those to establish normal MP LSPs.
When a downstream LSR sends a Label Mapping message for MP LSP to its
upstream LSR it MAY include an LDP MP Status TLV that carries a MBB
Status Code to indicate MBB procedures apply to the LSP. This new
MBB Status Code MAY also appear in an LDP Notification message used
by an upstream LSR to signal LSP state #3 to the downstream LSR; that
is, that the upstream LSRs state for the LSP exists and that it has
received notification from its upstream LSR that the LSP is in state
#3.
The MBB Status is a type of the LDP MP Status Value Element as
described in Section 5.1. It is encoded as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| MBB Type = 1 | Length = 1 | Status code |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Minei & Wijnands Expires February 5, 2012 [Page 29]
Internet-Draft P2MP and MP2MP LSP Setup with LDP August 2011
MBB Type: Type 1 (to be assigned by IANA)
Length: 1
Status code: 1 = MBB request
2 = MBB ack
8.3. The MBB capability
An LSR MAY advertise that it is capable of handling MBB LSPs using
the capability advertisement as defined in [RFC5561]. The LDP MP MBB
capability has the following format:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|1|0| LDP MP MBB Capability | Length = 1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|S| Reserved |
+-+-+-+-+-+-+-+-+
Note: LDP MP MBB Capability (Pending IANA assignment)
S: As specified in [RFC5561]
If an LSR has not advertised that it is MBB capable, its LDP peers
MUST NOT send it messages which include MBB parameters. If an LSR
receives a Label Mapping message with a MBB parameter from downstream
LSR-D and its upstream LSR-U has not advertised that it is MBB
capable, the LSR MUST send an MBB notification immediatly to LSR-U
(see Section 8.4). If this happens an MBB MP LSP will not be
established, but normal a MP LSP will be the result.
8.4. The MBB procedures
8.4.1. Terminology
1. MBB LSP <X, Y>: A P2MP or MP2MP Make Before Break (MBB) LSP entry
with Root Node Address X and Opaque Value Y.
2. A(N, L): An Accepting element that consists of an upstream
Neighbor N and Local label L. This LSR assigned label L to
neighbor N for a specific MBB LSP. For an active element the
corresponding Label is stored in the label forwarding database.
Minei & Wijnands Expires February 5, 2012 [Page 30]
Internet-Draft P2MP and MP2MP LSP Setup with LDP August 2011
3. iA(N, L): An inactive Accepting element that consists of an
upstream neighbor N and local Label L. This LSR assigned label L
to neighbor N for a specific MBB LSP. For an inactive element
the corresponding Label is not stored in the label forwarding
database.
4. F(N, L): A Forwarding state that consists of downstream Neighbor
N and Label L. This LSR is sending label packets with label L to
neighbor N for a specific FEC.
5. F'(N, L): A Forwarding state that has been marked for sending a
MBB Notification message to Neighbor N with Label L.
6. MBB Notification <X, Y, L>: A LDP notification message with a MP
LSP <X, Y>, Label L and MBB Status code 2.
7. MBB Label Mapping <X, Y, L>: A P2MP Label Mapping or MP2MP Label
Mapping downstream with a FEC element <X, Y>, Label L and MBB
Status code 1.
8.4.2. Accepting elements
An accepting element represents a specific label value L that has
been advertised to a neighbor N for a MBB LSP <X, Y> and is a
candidate for accepting labels switched packets on. An LSR can have
two accepting elements for a specific MBB LSP <X, Y> LSP, only one of
them MUST be active. An active element is the element for which the
label value has been installed in the label forwarding database. An
inactive accepting element is created after a new upstream LSR is
chosen and is pending to replace the active element in the label
forwarding database. Inactive elements only exist temporarily while
switching to a new upstream LSR. Once the switch has been completed
only one active element remains. During network convergence it is
possible that an inactive accepting element is created while an other
inactive accepting element is pending. If that happens the older
inactive accepting element MUST be replaced with an newer inactive
element. If an accepting element is removed a Label Withdraw has to
be send for label L to neighbor N for <X, Y>.
8.4.3. Procedures for upstream LSR change
Suppose a node Z has a MBB LSP <X, Y> with an active accepting
element A(N1, L1). Due to a routing change it detects a new best
path for root X and selects a new upstream LSR N2. Node Z allocates
a new local label L2 and creates an inactive accepting element iA(N2,
L2). Node Z sends MBB Label Mapping <X, Y, L2>to N2 and waits for
the new upstream LSR N2 to respond with a MBB Notification for <X, Y,
L2>. During this transition phase there are two accepting elements,
Minei & Wijnands Expires February 5, 2012 [Page 31]
Internet-Draft P2MP and MP2MP LSP Setup with LDP August 2011
the element A(N1, L1) still accepting packets from N1 over label L1
and the new inactive element iA(N2, L2).
While waiting for the MBB Notification from upstream LSR N2, it is
possible that another transition occurs due to a routing change.
Suppose the new upstream LSR is N3. An inactive element iA(N3, L3)
is created and the old inactive element iA(N2, L2) MUST be removed.
A label withdraw MUST be sent to N2 for <X, Y, L2>. The MBB
Notification for <X, Y, L2> from N2 will be ignored because the
inactive element is removed.
It is possible that the MBB Notification from upstream LSR is never
received due to link or node failure. To prevent waiting
indefinitely for the MBB Notification a timeout SHOULD be applied.
As soon as the timer expires, the procedures in Section 8.4.5 are
applied as if a MBB Notification was received for the inactive
element. If a downstream LSR detects that the old upstream LSR went
down while waiting for the MBB Notification from the new upstream
LSR, the downstream LSR can immediately proceed without waiting for
the timer to expire.
8.4.4. Receiving a Label Mapping with MBB status code
Suppose node Z has state for a MBB LSP <X, Y> and receives a MBB
Label Mapping <X, Y, L2> from N2. A new forwarding state F(N2, L2)
will be added to the MP LSP if it did not already exist. If this MBB
LSP has an active accepting element or node Z is the root of the MBB
LSP a MBB notification <X, Y, L2)> is sent to node N2. If node Z has
an inactive accepting element it marks the Forwarding state as <X, Y,
F'(N2, L2)>. If router Z upstream LSR for <X, Y> happens to be N2,
then Z MUST NOT send an MBB notification to N2 at once. Sending the
MBB notification to N2 must be done only after Z upstream for <X, Y>
stops being N2.
8.4.5. Receiving a Notification with MBB status code
Suppose node Z receives a MBB Notification <X, Y, L> from N. If node
Z has state for MBB LSP <X, Y> and an inactive accepting element
iA(N, L) that matches with N and L, we activate this accepting
element and install label L in the label forwarding database. If an
other active accepting was present it will be removed from the label
forwarding database.
If this MBB LSP <X, Y> also has Forwarding states marked for sending
MBB Notifications, like <X, Y, F'(N2, L2)>, MBB Notifications are
sent to these downstream LSRs. If node Z receives a MBB Notification
for an accepting element that is not inactive or does not match the
Label value and Neighbor address, the MBB notification is ignored.
Minei & Wijnands Expires February 5, 2012 [Page 32]
Internet-Draft P2MP and MP2MP LSP Setup with LDP August 2011
8.4.6. Node operation for MP2MP LSPs
The procedures described above apply to the downstream path of a
MP2MP LSP. The upstream path of the MP2MP is setup as normal without
including a MBB Status code. If the MBB procedures apply to a MP2MP
downstream FEC element, the upstream path to a node N is only
installed in the label forwarding database if node N is part of the
active accepting element. If node N is part of an inactive accepting
element, the upstream path is installed when this inactive accepting
element is activated.
9. Typed Wildcard for mLDP FEC Element
The format of the mLDP FEC Typed Wildcard FEC is as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Typed Wcard | Type | Len = 2 | AFI ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
~ |
+-+-+-+-+-+-+-+-+
Type Wcard: As specified in [RFC5918]
Type: The type of FEC Element Type. Either the P2MP FEC Element or
the MP2MP FEC Element using the values defined for those FEC
Elements when carried in the FEC TLV as defined in this document.
Len: Len FEC Type Info, two octets (=0x02).
AFI: Address Family, two octet quantity containing a value from
IANA's "Address Family Numbers" registry.
10. Security Considerations
The same security considerations apply as for the base LDP
specification, as described in [RFC5036].
The protocol specified in this document does not provide any
authorization mechanism for controlling the set of LSRs that may join
a given MP LSP. If such authorization is desirable, additional
Minei & Wijnands Expires February 5, 2012 [Page 33]
Internet-Draft P2MP and MP2MP LSP Setup with LDP August 2011
mechanisms, outside the scope of this document, are needed. Note
that authorization policies cannot be implemented and/or configure
solely at the root node of the LSP, because the root node does not
learn the identities of all the leaf nodes.
11. IANA Considerations
This document creates three new registries to be managed by IANA.
1. "LDP MP Opaque Value Element basic type"
The range is 0-255, with the following values allocated in this
document:
1: Generic LSP identifier
255: Extended Type field is present in the following two bytes
The allocation policy for this space is 'Standards Action with
Early Allocation'
2. "LDP MP Opaque Value Element extended type"
The range is 0-65335, with the following allocation policies:
0-32767: Standards Action with Early Allocation
32768-65535: First Come, First Served
3. "LDP MP Status Value Element type"
The range is 0-255, with the following value allocated in this
document:
1: MBB Status
The allocation policy for this space is 'Standards Action with
Early Allocation'
The requested code point values listed below have been allocated by
IANA through early allocation.
This document requires allocation of three new code points from the
IANA managed LDP registry "Forwarding Equivalence Class (FEC) Type
Name Space". The values are:
Minei & Wijnands Expires February 5, 2012 [Page 34]
Internet-Draft P2MP and MP2MP LSP Setup with LDP August 2011
P2MP FEC type - requested value 0x06
MP2MP-up FEC type - requested value 0x07
MP2MP-down FEC type - requested value 0x08
This document requires the assignment of three new code points for
three new Capability Parameter TLVs from the IANA managed LDP
registry "TLV Type Name Space", corresponding to the advertisement of
the P2MP, MP2MP and MBB capabilities. The values requested are:
P2MP Capability Parameter - requested value 0x0508
MP2MP Capability Parameter - requested value 0x0509
MBB Capability Parameter - requested value 0x050A
This document requires the assignment of a LDP Status Code to
indicate a LDP MP Status TLV is following in the Notification
message. The value requested from the IANA managed LDP registry "LDP
Status Code Name Space" is:
LDP MP status - requested value 0x00000040
This document requires the assigment of a new code point for a LDP MP
Status TLV. The value requested from the IANA managed LDP registry
"LDP TLV Type Name Space" is:
LDP MP Status TLV Type - requested value 0x096F
12. Acknowledgments
The authors would like to thank the following individuals for their
review and contribution: Nischal Sheth, Yakov Rekhter, Rahul
Aggarwal, Arjen Boers, Eric Rosen, Nidhi Bhaskar, Toerless Eckert,
George Swallow, Jin Lizhong, Vanson Lim, Adrian Farrel, Thomas Morin
and Ben Niven-Jenkins.
13. Contributing authors
Below is a list of the contributing authors in alphabetical order:
Minei & Wijnands Expires February 5, 2012 [Page 35]
Internet-Draft P2MP and MP2MP LSP Setup with LDP August 2011
Shane Amante
Level 3 Communications, LLC
1025 Eldorado Blvd
Broomfield, CO 80021
US
Email: Shane.Amante@Level3.com
Luyuan Fang
Cisco Systems
300 Beaver Brook Road
Boxborough, MA 01719
US
Email: lufang@cisco.com
Hitoshi Fukuda
NTT Communications Corporation
1-1-6, Uchisaiwai-cho, Chiyoda-ku
Tokyo 100-8019,
Japan
Email: hitoshi.fukuda@ntt.com
Yuji Kamite
NTT Communications Corporation
Tokyo Opera City Tower
3-20-2 Nishi Shinjuku, Shinjuku-ku,
Tokyo 163-1421,
Japan
Email: y.kamite@ntt.com
Kireeti Kompella
Juniper Networks
1194 N. Mathilda Ave.
Sunnyvale, CA 94089
US
Email: kireeti@juniper.net
Ina Minei
Juniper Networks
1194 N. Mathilda Ave.
Sunnyvale, CA 94089
US
Email: ina@juniper.net
Minei & Wijnands Expires February 5, 2012 [Page 36]
Internet-Draft P2MP and MP2MP LSP Setup with LDP August 2011
Jean-Louis Le Roux
France Telecom
2, avenue Pierre-Marzin
Lannion, Cedex 22307
France
Email: jeanlouis.leroux@francetelecom.com
Bob Thomas
Cisco Systems, Inc.
300 Beaver Brook Road
Boxborough, MA, 01719
E-mail: bobthomas@alum.mit.edu
Lei Wang
Telenor
Snaroyveien 30
Fornebu 1331
Norway
Email: lei.wang@telenor.com
IJsbrand Wijnands
Cisco Systems, Inc.
De kleetlaan 6a
1831 Diegem
Belgium
E-mail: ice@cisco.com
14. References
14.1. Normative References
[RFC5036] Andersson, L., Minei, I., and B. Thomas, "LDP
Specification", RFC 5036, October 2007.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC3031] Rosen, E., Viswanathan, A., and R. Callon, "Multiprotocol
Label Switching Architecture", RFC 3031, January 2001.
[RFC5331] Aggarwal, R., Rekhter, Y., and E. Rosen, "MPLS Upstream
Label Assignment and Context-Specific Label Space",
RFC 5331, August 2008.
Minei & Wijnands Expires February 5, 2012 [Page 37]
Internet-Draft P2MP and MP2MP LSP Setup with LDP August 2011
[I-D.ietf-mpls-ldp-upstream]
Aggarwal, R. and J. Roux, "MPLS Upstream Label Assignment
for LDP", draft-ietf-mpls-ldp-upstream-10 (work in
progress), February 2011.
[RFC5561] Thomas, B., Raza, K., Aggarwal, S., Aggarwal, R., and JL.
Le Roux, "LDP Capabilities", RFC 5561, July 2009.
[RFC5918] Asati, R., Minei, I., and B. Thomas, "Label Distribution
Protocol (LDP) 'Typed Wildcard' Forward Equivalence Class
(FEC)", RFC 5918, August 2010.
[ITU.V42.1994]
International Telecommunications Union, "Error-correcting
Procedures for DCEs Using Asynchronous-to-Synchronous
Conversion", ITU-T Recommendation V.42, 1994.
http://www.itu.int/rec/T-REC-V.42-200203-I
14.2. Informative References
[RFC4875] Aggarwal, R., Papadimitriou, D., and S. Yasukawa,
"Extensions to Resource Reservation Protocol - Traffic
Engineering (RSVP-TE) for Point-to-Multipoint TE Label
Switched Paths (LSPs)", RFC 4875, May 2007.
[I-D.ietf-mpls-mp-ldp-reqs]
Morin, T., "Requirements for Point-To-Multipoint
Extensions to the Label Distribution Protocol",
draft-ietf-mpls-mp-ldp-reqs-06 (work in progress),
December 2010.
[I-D.ietf-l3vpn-2547bis-mcast]
Aggarwal, R., Bandi, S., Cai, Y., Morin, T., Rekhter, Y.,
Rosen, E., Wijnands, I., and S. Yasukawa, "Multicast in
MPLS/BGP IP VPNs", draft-ietf-l3vpn-2547bis-mcast-10 (work
in progress), January 2010.
[RFC5332] Eckert, T., Rosen, E., Aggarwal, R., and Y. Rekhter, "MPLS
Multicast Encapsulations", RFC 5332, August 2008.
Minei & Wijnands Expires February 5, 2012 [Page 38]
Internet-Draft P2MP and MP2MP LSP Setup with LDP August 2011
Authors' Addresses
Ina Minei (editor)
Juniper Networks
1194 N. Mathilda Ave.
Sunnyvale, CA 94089
US
Email: ina@juniper.net
IJsbrand Wijnands (editor)
Cisco Systems, Inc.
De kleetlaan 6a
Diegem 1831
Belgium
Email: ice@cisco.com
Kireeti Kompella
Juniper Networks
1194 N. Mathilda Ave.
Sunnyvale, CA 94089
US
Email: kireeti@juniper.net
Bob Thomas
300 Beaver Brook Road
Boxborough 01719
US
Email: bobthomas@alum.mit.edu
Minei & Wijnands Expires February 5, 2012 [Page 39]
