Network Working Group
INTERNET-DRAFT M.Venkatesan
Intended Status: Standards Track Dell Inc.
Expires: May 08, 2014 Kannan KV Sampath
Redeem
Sam K. Aldrin
Huawei Technologies
Thomas D. Nadeau
Juniper Networks
November 04, 2013
MPLS-TP Traffic Engineering (TE) Management Information Base (MIB)
draft-ietf-mpls-tp-te-mib-07.txt
Abstract
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in the Internet community.
In particular, it describes managed objects of Tunnels, Identifiers,
Label Switching Router and Textual conventions for Multiprotocol
Label Switching (MPLS) based Transport Profile (TP).
Status of this Memo
This Internet-Draft is submitted to IETF in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
This Internet-Draft will expire on May 08, 2014.
Venkatesan, et al. Expires May 08, 2014 [Page 1]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
Copyright and License Notice
Copyright (c) 2013 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. The Internet-Standard Management Framework . . . . . . . . . . 4
3. Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3.1. Conventions used in this document . . . . . . . . . . . . . 4
3.2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . 4
3.3. Acronyms . . . . . . . . . . . . . . . . . . . . . . . . . 6
4. Motivations . . . . . . . . . . . . . . . . . . . . . . . . . . 6
5. Feature List . . . . . . . . . . . . . . . . . . . . . . . . . 6
6. Brief description of MPLS-TE-EXT-STD-MIB Objects . . . . . . . 7
6.1. mplsTunnelExtNodeConfigTable . . . . . . . . . . . . . . . 7
6.2. mplsTunnelExtNodeIpMapTable . . . . . . . . . . . . . . . . 8
6.3. mplsTunnelExtNodeIccMapTable . . . . . . . . . . . . . . . 8
6.4. mplsTunnelExtTable . . . . . . . . . . . . . . . . . . . . 8
6.5. mplsTunnelExtReversePerfTable . . . . . . . . . . . . . . . 8
7. MIB Module Interdependencies . . . . . . . . . . . . . . . . . 9
8. Dependencies between MIB Module Tables . . . . . . . . . . . . 11
9.1. Example of MPLS-TP static co-routed bidirectional tunnel
setup . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
9.1.1. mplsTunnelEntry . . . . . . . . . . . . . . . . . . . . 12
9.1.2. mplsTunnelExtEntry . . . . . . . . . . . . . . . . . . 13
9.1.3. Forward direction mplsOutSegmentEntry . . . . . . . . . 14
9.1.4. Reverse direction mplsInSegmentEntry . . . . . . . . . 14
9.1.5. Forward direction mplsXCEntry . . . . . . . . . . . . . 14
9.1.6. Reverse direction mplsXCEntry . . . . . . . . . . . . . 15
9.1.7. Forward direction mplsXCExtEntry . . . . . . . . . . . 15
9.1.8. Reverse direction mplsXCExtEntry . . . . . . . . . . . 15
9.1.9. mplsTunnelExtReversePerfTable . . . . . . . . . . . . . 15
9.2. Example of MPLS-TP static associated bidirectional tunnel
setup . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
9.2.1. Forward direction mplsTunnelEntry . . . . . . . . . . . 16
9.2.2. Forward direction mplsTunnelExtEntry . . . . . . . . . 17
9.2.3. Forward direction mplsOutSegmentTable . . . . . . . . . 17
Venkatesan, et al. Expires May 08, 2014 [Page 2]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
9.2.4. Forward direction mplsXCEntry . . . . . . . . . . . . . 17
9.2.5. Forward direction mplsXCExtEntry . . . . . . . . . . . 18
9.2.6. Reverse direction mplsTunnelEntry . . . . . . . . . . . 18
9.2.7. Reverse direction mplsTunnelExtEntry . . . . . . . . . 19
9.2.8. Reverse direction mplsInSegmentEntry . . . . . . . . . 19
9.2.9. Reverse direction mplsXCEntry . . . . . . . . . . . . . 19
9.2.10. Reverse direction mplsXCExtEntry . . . . . . . . . . . 20
9.3.1. mplsTunnelEntry . . . . . . . . . . . . . . . . . . . . 20
9.3.2. mplsTunnelExtEntry . . . . . . . . . . . . . . . . . . 21
9.3.3. Forward direction mplsOutSegmentEntry . . . . . . . . . 21
9.3.4. Reverse direction mplsInSegmentEntry . . . . . . . . . 21
9.3.5. Forward direction mplsXCEntry . . . . . . . . . . . . . 22
9.3.6. Reverse direction mplsXCEntry . . . . . . . . . . . . . 22
9.3.7. Forward direction mplsXCExtEntry . . . . . . . . . . . 22
9.3.8. Reverse direction mplsXCExtEntry . . . . . . . . . . . 22
9.3.9. mplsTunnelExtReversePerfTable . . . . . . . . . . . . . 22
10. MPLS Textual Convention Extension MIB definitions . . . . . . 22
11. MPLS Identifier MIB definitions . . . . . . . . . . . . . . . 25
12. MPLS LSR Extension MIB definitions . . . . . . . . . . . . . . 30
13. MPLS Tunnel Extension MIB definitions . . . . . . . . . . . . 35
14. Security Consideration . . . . . . . . . . . . . . . . . . . . 55
15. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 56
15.1. IANA Considerations for MPLS-TC-EXT-STD-MIB . . . . . . . 56
15.2. IANA Considerations for MPLS-ID-STD-MIB . . . . . . . . . 57
15.3. IANA Considerations for MPLS-LSR-EXT-STD-MIB . . . . . . . 57
15.4. IANA Considerations for MPLS-TE-EXT-STD-MIB . . . . . . . 57
16. References . . . . . . . . . . . . . . . . . . . . . . . . . . 57
16.1. Normative References . . . . . . . . . . . . . . . . . . . 57
16.2. Informative References . . . . . . . . . . . . . . . . . 57
17. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 58
18. Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . 58
Venkatesan, et al. Expires May 08, 2014 [Page 3]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
1. Introduction
This memo defines a portion of the Management Information Base (MIB) for
use with network management protocols in the Internet community. In
particular, it describes managed objects of Tunnels, Identifiers, Label
Switching Router and Textual conventions for Multiprotocol Label
Switching (MPLS) based Transport Profile (TP). These MIB modules extend
the existing MPLS MIB objects for both MPLS-TP and Non-MPLS-TP
operations, so the MPLS-TP name is not included in the MIB module name.
The existing Multiprotocol Label Switching (MPLS) Traffic Engineering
(TE) Management Information Base (MIB) [RFC3812] and Generalized
Multiprotocol Label Switching (GMPLS) Traffic Engineering Management
Information Base [RFC4802] do not support the transport network
requirements of NON-IP based management and static bidirectional
tunnels. These MIB modules should be used in conjunction with [RFC3812]
and companion document [RFC3813] for MPLS-TP tunnel configuration and
management.
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "MAY", and "OPTIONAL" in this document are to be
interpreted as described in BCP 14, RFC2119.
2. The Internet-Standard Management Framework
For a detailed overview of the documents that describe the current
Internet-Standard Management Framework, please refer to section 7 of
RFC3410 [RFC3410].
Managed objects are accessed via a virtual information store, termed the
Management Information Base or MIB. MIB objects are generally accessed
through the Simple Network Management Protocol (SNMP). Objects in the
MIB are defined using the mechanisms defined in the Structure of
Management Information (SMI). This memo specifies a MIB module that is
compliant to the SMIv2, which is described in STD 58, RFC2578, STD 58,
RFC2579 and STD58, RFC2580.
3. Overview
3.1. Conventions used in this document
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
3.2. Terminology
Venkatesan, et al. Expires May 08, 2014 [Page 4]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
This document uses terminology from the Multiprotocol Label Switching
Architecture [RFC3031], Multiprotocol Label Switching (MPLS) Traffic
Engineering (TE) Management Information Base (MIB) [RFC3812],
Multiprotocol Label Switching (MPLS) Label Switching Router (LSR)
Management Information Base (MIB) [RFC3813] and MPLS Transport Profile
(MPLS-TP) Identifiers [RFC6370].
Venkatesan, et al. Expires May 08, 2014 [Page 5]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
3.3. Acronyms
CC: Country Code
GMPLS: Generalized Multi-Protocol Label Switching
ICC: ITU Carrier Code
IP: Internet Protocol
ITU: International Telecommunication Union
ITU-T: ITU Telecommunication Standardization Sector
LSP: Label Switching Path
LSR: Label Switching Router
MIB: Management Information Base
MPLS: Multi-Protocol Label Switching
MPLS-TP: MPLS Transport Profile
OSPF: Open Shortest Path First
PW: Pseudowire
TE: Traffic Engineering
TP: Transport Profile
4. Motivations
Multiprotocol Label Switching (MPLS) Traffic Engineering (TE) Management
Information Base (MIB) [RFC3812] provides support for Traffic
Engineering tunnels. However, with MPLS-TP, the characteristics of
Tunnels were enhanced. For example, MPLS-TP tunnels are bidirectional in
nature and could be used in non-IP environments. As the existing MPLS-
TE-STD-MIB is not sufficient to capture all the characteristics of the
tunnels, enhancing the MIB to support MPLS TP tunnels is required. As
most of the attributes of MPLS Traffic Engineering tunnels are also
applicable to MPLS-TP tunnels, it is optimal to re-use the existing MIB
definition instead of a new MIB.
This document defines four MIB modules, namely MPLS-TE-EXT-STD-MIB,
MPLS-TC-EXT-STD-MIB, MPLS-ID-STD-MIB and MPLS-LSR-EXT-STD-MIB. As these
new MIB modules are required for MPLS-TP functionality, these are
retained in the same document, instead of a separate document.
5. Feature List
The MPLS-TE-EXT-STD-MIB is designed to satisfy the following
requirements and constraints:
The MIB module supports static and signaling point-to-point, co-routed
bi-directional and associated bi-directional tunnels.
- The MPLS tunnels need not be interfaces, but it is possible
to configure a TP tunnel as an interface.
- The mplsTunnelTable [RFC3812] to be also used for MPLS-TP
Venkatesan, et al. Expires May 08, 2014 [Page 6]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
tunnels
- The mplsTunnelTable is extended to support MPLS-TP specific
objects.
- A node configuration table (mplsTunnelExtNodeConfigTable)
is used to translate the Global_ID::Node_ID or
ICC_Operator_ID::Node_ID to the local identifier in order
to index mplsTunnelTable.
- The MIB module supports persistent, as well as non-persistent
tunnels.
6. Brief description of MPLS-TE-EXT-STD-MIB Objects
The objects described in this section support the functionality
described in documents [RFC5654] and [RFC6370]. The tables support
both IP compatible and ICC based tunnel configurations.
6.1. mplsTunnelExtNodeConfigTable
The mplsTunnelExtNodeConfigTable is used to assign a local identifier
for a given ICC_Operator_ID::Node_ID or Global_ID::Node_ID
combination as defined in [RFC6923] and [RFC6370] respectively.
The CC is a string of two alphabetic characters represented with
upper case letters (i.e., A-Z). The ICC is a string of one to six
characters, each character being either alphabetic (i.e. A-Z)
or numeric (i.e. 0-9) characters. Alphabetic characters in the ICC
should be represented with upper case letters. In the IP compatible
mode, Global_ID::Node_ID, is used to uniquely identify a node.
Each ICC_Operator_ID::Node_ID or Global_ID::Node_ID contains one
unique entry in the table representing a node. Every node is assigned
a local identifier within a range of 0 to 16777215. This local
identifier is used for indexing into mplsTunnelTable as
mplsTunnelIngressLSRId and mplsTunnelEgressLSRId.
For IP compatible environment, MPLS-TP tunnel is indexed by Tunnel
Index, Tunnel Instance, Source Global_ID, Source Node_ID, Destination
Global_ID and Destination Node_ID.
For ICC based environment, MPLS-TP tunnel is indexed by Tunnel Index,
Tunnel Instance, Source CC, Source ICC, Source Node_ID, Destination
CC, Destination ICC and Destination Node_ID.
As mplsTunnelTable is indexed by mplsTunnelIndex,
mplsTunnelInstance, mplsTunnelIngressLSRId, and
Venkatesan, et al. Expires May 08, 2014 [Page 7]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
mplsTunnelEgressLSRId, the MPLS-TP tunnel identifiers cannot be
used directly.
The mplsTunnelExtNodeConfigTable will be used to store an entry for
ICC_Operator_ID::Node_ID or Global_ID::Node_ID with a local
identifier to be used as LSR ID in mplsTunnelTable. As the regular TE
tunnels use IP address as LSR ID, the local identifier should be
below the first valid IP address, which is 16777216[1.0.0.0].
6.2. mplsTunnelExtNodeIpMapTable
The read-only mplsTunnelExtNodeIpMaptable is used to query the local
identifier assigned and stored in mplsTunnelExtNodeConfigTable for
a given Global_ID::Node_ID. In order to query the local identifier,
in the IP compatible mode, this table is indexed with
Global_ID::Node_ID. In the IP compatible mode for a TP tunnel,
Global_ID::Node_ID is used.
A separate query is made to get the local identifier of both
Ingress and Egress Global_ID::Node_ID identifiers. These local
identifiers are used as mplsTunnelIngressLSRId and
mplsTunnelEgressLSRId, while indexing mplsTunnelTable.
6.3. mplsTunnelExtNodeIccMapTable
The read-only mplsTunnelExtNodeIccMapTable is used to query the local
identifier assigned and stored in the mplsTunnelExtNodeConfigTable
for a given ICC_Operator_ID::Node_ID.
A separate query is made to get the local identifier of both
Ingress and Egress ICC_Operator_ID::Node_ID. These local identifiers
are used as mplsTunnelIngressLSRId and mplsTunnelEgressLSRId,
while indexing mplsTunnelTable.
6.4. mplsTunnelExtTable
mplsTunnelExtTable extends the mplsTunnelTable in order to support
MPLS-TP tunnels with additional objects. All the additional
attributes specific to supporting TP tunnel are contained in this
extended table and could be accessed with the mplsTunnelTable
indices.
6.5. mplsTunnelExtReversePerfTable
This table sparse augments the mplsTunnelTable to provide per-tunnel
packet performance information for the reverse direction of a
bidirectional tunnel. It can be seen as supplementing the
Venkatesan, et al. Expires May 08, 2014 [Page 8]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
mplsTunnelPerfTable, which augments the mplsTunnelTable.
7. MIB Module Interdependencies
This section provides an overview of the relationship between the
MPLS-TP TE MIB module and other MPLS MIB modules.
The arrows in the following diagram show a 'depends on'
relationship. A relationship "MIB module A depends on MIB module B"
means that MIB module A uses an object, object identifier, or
textual convention defined in MIB module B, or that MIB module A
contains a pointer (index or RowPointer) to an object in
MIB module B.
Venkatesan, et al. Expires May 08, 2014 [Page 9]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
MPLS-TC-EXT-STD-MIB
^
|
|
+<---- MPLS-ID-STD-MIB
^
| |
+<---- MPLS-TE-EXT-STD-MIB
| |
| V
| MPLS-TE-STD-MIB
| |
| |
| V
| MPLS-LSR-STD-MIB
| ^
| |
| |
+------MPLS-LSR-EXT-STD-MIB
Thus:
- All the new MPLS extension MIB modules depend on
MPLS-TC-EXT-STD-MIB.
- MPLS-ID-STD-MIB contains references to objects in
MPLS-TE-STD-MIB [RFC3812].
- MPLS-TE-EXT-STD-MIB contains references to objects in
MPLS-TE-STD-MIB [RFC3812].
- MPLS-LSR-EXT-STD-MIB contains references to objects in
MPLS-LSR-STD-MIB [RFC3813].
MPLS-TE-STD-MIB [RFC3812] is extended by MPLS-TE-EXT-STD-MIB
MIB module for associating the reverse direction tunnel
information.
Note that the nature of the 'extends' relationship
is a sparse augmentation so that the entry in the
mplsTunnelExtTable has the same index values as the in the
mplsTunnelTable.
MPLS-LSR-STD-MIB [RFC3813] is extended by MPLS-LSR-EXT-STD-MIB
MIB module for pointing back to the tunnel entry for easy tunnel
access from XC entry.
Note that the nature of the 'extends' relationship
Venkatesan, et al. Expires May 08, 2014 [Page 10]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
is a sparse augmentation so that the entry in the
mplsXCExtTable has the same index values as the in the mplsXCTable.
8. Dependencies between MIB Module Tables
The tables in MPLS-TE-EXT-STD-MIB are related as shown on the diagram
below. The arrows indicate a reference from one table to another.
mplsTunnelExtNodeConfigTable
^ mplsXCExtTable
| | ^
| +---------+ |
| | |
| V V
mplsTunnelTable ---->mplsXCTable
^
|
|
mplsTunnelExtTable
An existing mplsTunnelTable uses the mplsTunnelExtNodeConfigTable
table to map the Global_ID::Node_ID and/or ICC_Operator_ID::Node_ID
with the local number in order to accommodate in the existing tunnel
table's ingress/egress LSR-id.
New mplsTunnelExtTable table provides the reverse direction LSP
information for the existing tunnel table in order to achieve
bidirectional LSPs.
mplsXCExtTable is extended from mplsLsrXCTable to provide
backward reference to tunnel entry.
9. Example of MPLS-TP Tunnel Setup
In this section, we provide an example of the IP based MPLS-TP
bidirectional tunnel setup. This example provides the usage of
MPLS-TP Tunnel MIB along with the extended new MIB modules introduced
in this document.
Do note that a MPLS-TP tunnel could be setup statically as well as
signaled via control plane. This example considers accessing MIB
objects on a head-end for a static and signaling MPLS-TP tunnels.
Only relevant objects which are applicable for MPLS-TP tunnel are
illustrated here.
In mplsTunnelExtNodeConfigTable:
{
-- Non-IP Ingress LSR-Id (Index to the table)
Venkatesan, et al. Expires May 08, 2014 [Page 11]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
mplsTunnelExtNodeConfigLocalId = 1,
mplsTunnelExtNodeConfigGlobalId = 1234,
mplsTunnelExtNodeConfigNodeId = 10,
-- Mandatory parameters needed to activate the row go here
mplsTunnelExtNodeConfigRowStatus = createAndGo (4)
-- Non-IP Egress LSR-Id (Index to the table)
mplsTunnelExtNodeConfigLocalId = 2,
mplsTunnelExtNodeConfigGlobalId = 1234,
mplsTunnelExtNodeConfigNodeId = 20,
-- Mandatory parameters needed to activate the row go here
mplsTunnelExtNodeConfigRowStatus = createAndGo (4)
}
This will create an entry in the mplsTunnelExtNodeConfigTable for a
Global_ID::Node_ID. A separate entry is made for both Ingress LSR
and Egress LSR.
The following read-only mplsTunnelExtNodeIpMapTable table is
populated automatically upon creating an entry in
mplsTunnelExtNodeConfigTable and this table is used to retrieve
the local identifier for the given Global_ID::Node_ID.
In mplsTunnelExtNodeIpMapTable:
{
-- Global_ID (Index to the table)
mplsTunnelExtNodeIpMapGlobalId = 1234,
-- Node Identifier (Index to the table)
mplsTunnelExtNodeIpMapNodeId = 10,
mplsTunnelExtNodeIpMapLocalId = 1
-- Global_ID (Index to the table)
mplsTunnelExtNodeIpMapGlobalId = 1234,
-- Node Identifier (Index to the table)
mplsTunnelExtNodeIpMapNodeId = 20,
mplsTunnelExtNodeIpMapLocalId = 2
}
9.1. Example of MPLS-TP static co-routed bidirectional tunnel setup
The following denotes the configured co-routed bidirectional
tunnel "head" entry:
9.1.1. mplsTunnelEntry
In mplsTunnelTable:
Venkatesan, et al. Expires May 08, 2014 [Page 12]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
{
mplsTunnelIndex = 1,
mplsTunnelInstance = 1,
-- Local map number created in mplsTunnelExtNodeConfigTable for
-- Ingress LSR-Id
mplsTunnelIngressLSRId = 1,
-- Local map number created in mplsTunnelExtNodeConfigTable for
-- Egress LSR-Id
mplsTunnelEgressLSRId = 2,
mplsTunnelName = "TP co-routed bidirectional LSP",
mplsTunnelDescr = "East to West",
mplsTunnelIsIf = true (1),
-- RowPointer MUST point to the first accessible column
mplsTunnelXCPointer =
mplsXCLspId.4.0.0.0.1.1.0.4.0.0.0.1,
mplsTunnelSignallingProto = none (1),
mplsTunnelSetupPrio = 0,
mplsTunnelHoldingPrio = 0,
mplsTunnelSessionAttributes = 0,
mplsTunnelLocalProtectInUse = false (0),
-- RowPointer MUST point to the first accessible column
mplsTunnelResourcePointer = mplsTunnelResourceMaxRate.5,
mplsTunnelInstancePriority = 1,
mplsTunnelHopTableIndex = 1,
mplsTunnelIncludeAnyAffinity = 0,
mplsTunnelIncludeAllAffinity = 0,
mplsTunnelExcludeAnyAffinity = 0,
mplsTunnelRole = head (1),
-- Mandatory parameters needed to activate the row go here
mplsTunnelRowStatus = createAndGo (4)
}
9.1.2. mplsTunnelExtEntry
-- An MPLS extension table
In mplsTunnelExtTable:
{
-- This opposite direction tunnel pointer MAY be point to 0.0
-- if co-routed bidirectional tunnel is managed by single tunnel
-- entry
mplsTunnelExtOppositeDirTnlPtr = 0.0
-- Set both the Ingress and Egress LocalId objects to TRUE as
-- this tunnel entry uses the local identifiers.
mplsTunnelExtIngressLSRLocalIdValid = true,
mplsTunnelExtEgressLSRLocalIdValid = true
}
Venkatesan, et al. Expires May 08, 2014 [Page 13]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
We must next create the appropriate in-segment and out-segment
entries. These are done in [RFC3813] using the mplsInSegmentTable and
mplsOutSegmentTable.
9.1.3. Forward direction mplsOutSegmentEntry
For the forward direction.
In mplsOutSegmentTable:
{
mplsOutSegmentIndex = 0x0000001,
mplsOutSegmentInterface = 13, -- outgoing interface
mplsOutSegmentPushTopLabel = true(1),
mplsOutSegmentTopLabel = 22, -- outgoing label
-- RowPointer MUST point to the first accessible column.
mplsOutSegmentTrafficParamPtr = 0.0,
mplsOutSegmentRowStatus = createAndGo (4)
}
9.1.4. Reverse direction mplsInSegmentEntry
For the reverse direction.
In mplsInSegmentTable:
{
mplsInSegmentIndex = 0x0000001
mplsInSegmentLabel = 21, -- incoming label
mplsInSegmentNPop = 1,
mplsInSegmentInterface = 13, -- incoming interface
-- RowPointer MUST point to the first accessible column.
mplsInSegmentTrafficParamPtr = 0.0,
mplsInSegmentRowStatus = createAndGo (4)
}
Next, two cross-connect entries are created in the mplsXCTable of the
MPLS-LSR-STD-MIB [RFC3813], thereby associating the newly created
segments together.
9.1.5. Forward direction mplsXCEntry
In mplsXCTable:
{
mplsXCIndex = 0x01,
mplsXCInSegmentIndex = 0x00000000,
mplsXCOutSegmentIndex = 0x00000001,
mplsXCLspId = 0x0102 -- unique ID
Venkatesan, et al. Expires May 08, 2014 [Page 14]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
-- only a single outgoing label
mplsXCLabelStackIndex = 0x00,
mplsXCRowStatus = createAndGo(4)
}
9.1.6. Reverse direction mplsXCEntry
In mplsXCTable:
{
mplsXCIndex = 0x01,
mplsXCInSegmentIndex = 0x00000001,
mplsXCOutSegmentIndex = 0x00000000,
mplsXCLspId = 0x0102 -- unique ID
-- only a single outgoing label
mplsXCLabelStackIndex = 0x00,
mplsXCRowStatus = createAndGo(4)
}
This table entry is extended by entry in the
mplsXCExtTable. Note that the nature of the 'extends'
relationship is a sparse augmentation so that the entry in the
mplsXCExtTable has the same index values as the entry in
the mplsXCTable.
9.1.7. Forward direction mplsXCExtEntry
In mplsXCExtTable (0x01, 0x00000000, 0x00000001)
{
-- Back pointer from XC table to Tunnel table
mplsXCExtTunnelPointer = mplsTunnelName.1.1.1.2
mplsXCExtOppositeDirXCPtr =
mplsXCLspId.4.0.0.0.1.4.0.0.0.1.1.0
}
9.1.8. Reverse direction mplsXCExtEntry
Next for the reverse direction:
In mplsXCExtTable (0x01, 0x00000001, 0x00000000)
{
-- Back pointer from XC table to Tunnel table
mplsXCExtTunnelPointer = mplsTunnelName.1.1.1.2
mplsXCExtOppositeDirXCPtr =
mplsXCLspId.4.0.0.0.1.1.0.4.0.0.0.1
}
9.1.9. mplsTunnelExtReversePerfTable
Venkatesan, et al. Expires May 08, 2014 [Page 15]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
The mplsTunnelExtReversePerfTable SHOULD be populated incase
the single tunnel entry is used for co-routed bidirectional tunnel
setup. The mplsTunnelPerfTable will have the forward direction
LSP performance counters and mplsTunnelExtReversePerfTable will have
the reverse direction LSP performance counters.
9.2. Example of MPLS-TP static associated bidirectional tunnel setup
The MPLS-TP associated bidirectional tunnel has two different
direction tunnels[Forward and Reverse LSPs] and these are
associated together using mplsTunnelExtTable. Two different
tunnel entries for both forward and reverse direction MAY be used
for co-routed bidirectional tunnel as well.
The following denotes the configured associated bidirectional forward
tunnel "head" entry:
9.2.1. Forward direction mplsTunnelEntry
In mplsTunnelTable:
{
mplsTunnelIndex = 1,
mplsTunnelInstance = 1,
-- Local map number created in mplsTunnelExtNodeConfigTable for
-- Ingress LSR-Id
mplsTunnelIngressLSRId = 1,
-- Local map number created in mplsTunnelExtNodeConfigTable for
-- Egress LSR-Id
mplsTunnelEgressLSRId = 2,
mplsTunnelName = "TP associated bi-directional
forward LSP",
mplsTunnelDescr = "East to West",
mplsTunnelIsIf = true (1),
-- RowPointer MUST point to the first accessible column
mplsTunnelXCPointer =
mplsXCLspId.4.0.0.0.1.1.0.4.0.0.0.1,
mplsTunnelSignallingProto = none (1),
mplsTunnelSetupPrio = 0,
mplsTunnelHoldingPrio = 0,
mplsTunnelSessionAttributes = 0,
mplsTunnelLocalProtectInUse = false (0),
-- RowPointer MUST point to the first accessible column
mplsTunnelResourcePointer = mplsTunnelResourceMaxRate.5,
mplsTunnelInstancePriority = 1,
mplsTunnelHopTableIndex = 1,
mplsTunnelIncludeAnyAffinity = 0,
Venkatesan, et al. Expires May 08, 2014 [Page 16]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
mplsTunnelIncludeAllAffinity = 0,
mplsTunnelExcludeAnyAffinity = 0,
mplsTunnelRole = head (1),
-- Mandatory parameters needed to activate the row go here
mplsTunnelRowStatus = createAndGo (4)
}
9.2.2. Forward direction mplsTunnelExtEntry
For Associated bidirectional forward LSP,
In mplsTunnelExtTable:
{
mplsTunnelExtOppositeDirPtr = mplsTunnelName.2.1.2.1
-- Set both the Ingress and Egress LocalId objects to TRUE as
-- this tunnel entry uses the local identifiers.
mplsTunnelExtIngressLSRLocalIdValid = true,
mplsTunnelExtEgressLSRLocalIdValid = true
}
9.2.3. Forward direction mplsOutSegmentTable
For the forward direction.
In mplsOutSegmentTable:
{
mplsOutSegmentIndex = 0x0000001,
mplsOutSegmentInterface = 13, -- outgoing interface
mplsOutSegmentPushTopLabel = true(1),
mplsOutSegmentTopLabel = 22, -- outgoing label
-- RowPointer MUST point to the first accessible column.
mplsOutSegmentTrafficParamPtr = 0.0,
mplsOutSegmentRowStatus = createAndGo (4)
}
9.2.4. Forward direction mplsXCEntry
In mplsXCTable:
{
mplsXCIndex = 0x01,
mplsXCInSegmentIndex = 0x00000000,
mplsXCOutSegmentIndex = 0x00000001,
mplsXCLspId = 0x0102 -- unique ID
-- only a single outgoing label
mplsXCLabelStackIndex = 0x00,
mplsXCRowStatus = createAndGo(4)
}
Venkatesan, et al. Expires May 08, 2014 [Page 17]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
9.2.5. Forward direction mplsXCExtEntry
In mplsXCExtTable (0x01, 0x00000000, 0x00000001)
{
-- Back pointer from XC table to Tunnel table
mplsXCExtTunnelPointer = mplsTunnelName.1.1.1.2
mplsXCExtOppositeDirXCPtr =
mplsXCLspId.4.0.0.0.1.4.0.0.0.1.1.0
}
9.2.6. Reverse direction mplsTunnelEntry
The following denotes the configured associated bidirectional reverse
tunnel "tail" entry:
In mplsTunnelTable:
{
mplsTunnelIndex = 2,
mplsTunnelInstance = 1,
-- Local map number created in mplsTunnelExtNodeConfigTable for
-- Ingress LSR-Id
mplsTunnelIngressLSRId = 2,
-- Local map number created in mplsTunnelExtNodeConfigTable for
-- Egress LSR-Id
mplsTunnelEgressLSRId = 1,
mplsTunnelName = "TP associated bi-directional
reverse LSP",
mplsTunnelDescr = "West to East",
mplsTunnelIsIf = true (1),
-- RowPointer MUST point to the first accessible column
mplsTunnelXCPointer =
mplsXCLspId.4.0.0.0.1.4.0.0.0.1.1.0,
mplsTunnelSignallingProto = none (1),
mplsTunnelSetupPrio = 0,
mplsTunnelHoldingPrio = 0,
mplsTunnelSessionAttributes = 0,
mplsTunnelLocalProtectInUse = false (0),
-- RowPointer MUST point to the first accessible column
mplsTunnelResourcePointer = mplsTunnelResourceMaxRate.5,
mplsTunnelInstancePriority = 1,
mplsTunnelHopTableIndex = 1,
mplsTunnelIncludeAnyAffinity = 0,
mplsTunnelIncludeAllAffinity = 0,
mplsTunnelExcludeAnyAffinity = 0,
mplsTunnelRole = head (1),
-- Mandatory parameters needed to activate the row go here
Venkatesan, et al. Expires May 08, 2014 [Page 18]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
mplsTunnelRowStatus = createAndGo (4)
}
9.2.7. Reverse direction mplsTunnelExtEntry
For Associated bidirectional reverse LSP,
In mplsTunnelExtTable:
{
mplsTunnelExtOppositeDirPtr = mplsTunnelName.1.1.1.2
-- Set both the Ingress and Egress LocalId objects to TRUE as
-- this tunnel entry uses the local identifiers.
mplsTunnelExtIngressLSRLocalIdValid = true,
mplsTunnelExtEgressLSRLocalIdValid = true
}
9.2.8. Reverse direction mplsInSegmentEntry
We must next create the appropriate in-segment and out-segment
entries. These are done in [RFC3813] using the mplsInSegmentTable and
mplsOutSegmentTable.
In mplsInSegmentTable:
{
mplsInSegmentIndex = 0x0000001
mplsInSegmentLabel = 21, -- incoming label
mplsInSegmentNPop = 1,
mplsInSegmentInterface = 13, -- incoming interface
-- RowPointer MUST point to the first accessible column.
mplsInSegmentTrafficParamPtr = 0.0,
mplsInSegmentRowStatus = createAndGo (4)
}
Next, two cross-connect entries are created in the mplsXCTable of the
MPLS-LSR-STD-MIB [RFC3813], thereby associating the newly created
segments together.
9.2.9. Reverse direction mplsXCEntry
In mplsXCTable:
{
mplsXCIndex = 0x01,
mplsXCInSegmentIndex = 0x00000001,
mplsXCOutSegmentIndex = 0x00000000,
mplsXCLspId = 0x0102 -- unique ID
-- only a single outgoing label
mplsXCLabelStackIndex = 0x00,
Venkatesan, et al. Expires May 08, 2014 [Page 19]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
mplsXCRowStatus = createAndGo(4)
}
This table entry is extended by entry in the
mplsXCExtTable. Note that the nature of the 'extends'
relationship is a sparse augmentation so that the entry in the
mplsXCExtTable has the same index values as the entry in
the mplsXCTable.
9.2.10. Reverse direction mplsXCExtEntry
Next for the reverse direction:
In mplsXCExtTable (0x01, 0x00000001, 0x00000000)
{
-- Back pointer from XC table to Tunnel table
mplsXCExtTunnelPointer = mplsTunnelName.2.1.2.1
mplsXCExtOppositeDirXCPtr =
mplsXCLspId.4.0.0.0.1.1.0.4.0.0.0.1
}
9.3. Example of MPLS-TP signaling co-routed bidirectional tunnel setup
The following denotes the configured co-routed bidirectional
tunnel "head" entry and in intermediate and tail-end nodes,
the tunnel table and its associated tables are created
by the local management subsystem (e.g. agent) when the MPLS TP
tunnel is signaled successfully. Refer [RFC3812] and [RFC4802]
for signaling tunnel table configuration examples.
9.3.1. mplsTunnelEntry
In mplsTunnelTable:
{
mplsTunnelIndex = 1,
mplsTunnelInstance = 0,
-- Local map number created in mplsTunnelExtNodeConfigTable for
-- Ingress LSR-Id, for the intermediate and tail-end nodes,
-- the local management entity is expected to pick a first available
-- local identifier which is not used in mplsTunnelTable.
mplsTunnelIngressLSRId = 1,
-- Local map number created in mplsTunnelExtNodeConfigTable for
-- Egress LSR-Id
mplsTunnelEgressLSRId = 2,
mplsTunnelName = "TP co-routed bidirectional LSP",
mplsTunnelDescr = "East to West",
Venkatesan, et al. Expires May 08, 2014 [Page 20]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
mplsTunnelIsIf = true (1),
-- RowPointer MUST point to the first accessible column
mplsTunnelXCPointer =
mplsXCLspId.4.0.0.0.1.1.0.4.0.0.0.1,
mplsTunnelSignallingProto = none (1),
mplsTunnelSetupPrio = 0,
mplsTunnelHoldingPrio = 0,
mplsTunnelSessionAttributes = 0,
mplsTunnelLocalProtectInUse = false (0),
-- RowPointer MUST point to the first accessible column
mplsTunnelResourcePointer = mplsTunnelResourceMaxRate.5,
mplsTunnelInstancePriority = 1,
mplsTunnelHopTableIndex = 1,
mplsTunnelIncludeAnyAffinity = 0,
mplsTunnelIncludeAllAffinity = 0,
mplsTunnelExcludeAnyAffinity = 0,
mplsTunnelRole = head (1),
-- Mandatory parameters needed to activate the row go here
mplsTunnelRowStatus = createAndGo (4)
}
9.3.2. mplsTunnelExtEntry
-- An MPLS extension table
In mplsTunnelExtTable:
{
-- This opposite direction tunnel pointer MAY be point to 0.0
-- if co-routed bidirectional tunnel is managed by single tunnel
-- entry
mplsTunnelExtOppositeDirTnlPtr = 0.0
-- Set both the Ingress and Egress LocalId objects to TRUE as
-- this tunnel entry uses the local identifiers.
mplsTunnelExtIngressLSRLocalIdValid = true,
mplsTunnelExtEgressLSRLocalIdValid = true
}
We must next create the appropriate in-segment and out-segment
entries. These are done in [RFC3813] using the mplsInSegmentTable and
mplsOutSegmentTable.
9.3.3. Forward direction mplsOutSegmentEntry
The forward direction mplsOutSegmentTable will be populated
automatically based on the information received from the signaling
protocol.
9.3.4. Reverse direction mplsInSegmentEntry
Venkatesan, et al. Expires May 08, 2014 [Page 21]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
The reverse direction mplsOutSegmentTable will be populated
automatically based on the information received from the signaling
protocol.
Next, two cross-connect entries are created in the mplsXCTable of the
MPLS-LSR-STD-MIB [RFC3813], thereby associating the newly created
segments together.
9.3.5. Forward direction mplsXCEntry
The forward direction mplsXCEntry will be populated as soon as the
forward path label information is available.
9.3.6. Reverse direction mplsXCEntry
The reverse direction mplsXCEntry will be populated as soon as the
reverse path label information is available.
This table entry is extended by entry in the mplsXCExtTable. Note
that the nature of the 'extends' relationship is a sparse
augmentation so that the entry in the mplsXCExtTable has the same
index values as the entry in the mplsXCTable.
9.3.7. Forward direction mplsXCExtEntry
Once the forward path information is negotiated using signaling
protocol, the forward direction mplsXCExtEntry will be created for
associating the opposite direction XC entry and tunnel table entry.
9.3.8. Reverse direction mplsXCExtEntry
Once the reverse path information is negotiated using signaling
protocol, the reverse direction mplsXCExtEntry will be created for
associating the opposite direction XC entry and tunnel table entry.
9.3.9. mplsTunnelExtReversePerfTable
The mplsTunnelExtReversePerfTable SHOULD be populated incase the
single tunnel entry is used for co-routed bidirectional tunnel setup.
The mplsTunnelPerfTable will have the forward direction LSP
performance counters and mplsTunnelExtReversePerfTable will have the
reverse direction LSP performance counters.
10. MPLS Textual Convention Extension MIB definitions
MPLS-TC-EXT-STD-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, Unsigned32
Venkatesan, et al. Expires May 08, 2014 [Page 22]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
FROM SNMPv2-SMI -- [RFC2578]
TEXTUAL-CONVENTION
FROM SNMPv2-TC -- [RFC2579]
mplsStdMIB
FROM MPLS-TC-STD-MIB -- [RFC3811]
;
mplsTcExtStdMIB MODULE-IDENTITY
LAST-UPDATED
"201311010000Z" -- November 01, 2013
ORGANIZATION
"Multiprotocol Label Switching (MPLS) Working Group"
CONTACT-INFO
"
Venkatesan Mahalingam
Dell Inc,
350 Holger way, San Jose, CA, USA
Email: venkat.mahalingams@gmail.com
Kannan KV Sampath
Redeem,
India
Email: kannankvs@gmail.com
Sam Aldrin
Huawei Technologies
2330 Central Express Way,
Santa Clara, CA 95051, USA
Email: aldrin.ietf@gmail.com
Thomas D. Nadeau
Juniper Networks
10 Technology Park Drive,
Westford, MA 01886
Email: tnadeau@juniper.net
"
DESCRIPTION
"Copyright (c) 2013 IETF Trust and the persons identified
as the document authors. All rights reserved.
This MIB module contains Textual Conventions for
LSPs and PWs of MPLS based transport networks."
-- Revision history.
Venkatesan, et al. Expires May 08, 2014 [Page 23]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
REVISION
"201311010000Z" -- November 01, 2013
DESCRIPTION
"MPLS Textual Convention Extensions"
::= { mplsStdMIB xxx } -- xxx to be replaced with correct value
MplsGlobalId ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This object contains the Textual Convention of IP based
operator unique identifier (Global_ID), the Global_ID can
contain the 2-octet or 4-octet value of the operator's
Autonomous System Number (ASN).
It is expected that the Global_ID will be derived from
the globally unique ASN of the autonomous system hosting
the PEs containing the actual AIIs.
The presence of a Global_ID based on the operator's
ASN ensures that the AII will be globally unique.
When the Global_ID is derived from a 2-octet AS number,
the two high-order octets of this 4-octet identifier
MUST be set to zero.
Further ASN 0 is reserved. A Global_ID of zero means
that no Global_ID is present. Note that a Global_ID of
zero is limited to entities contained within a single
operator and MUST NOT be used across an NNI.
A non-zero Global_ID MUST be derived from an ASN owned by
the operator."
REFERENCE
"MPLS Transport Profile (MPLS-TP) Identifiers, [RFC6370]
Section 3"
SYNTAX OCTET STRING (SIZE (4))
MplsCcId ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The CC (Country Code) is a string of two alphabetic
characters represented with upper case
letters (i.e., A-Z)."
REFERENCE
"MPLS-TP Identifiers Following ITU-T Conventions,
[RFC6923] Section 3"
SYNTAX OCTET STRING (SIZE (2))
Venkatesan, et al. Expires May 08, 2014 [Page 24]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
MplsIccId ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The ICC is a string of one to six characters, each
character being either alphabetic (i.e. A-Z) or
numeric (i.e. 0-9) characters.
Alphabetic characters in the ICC SHOULD be represented
with upper case letters. The size of the ICC string MUST be
zero if the ICC identifier is invalid."
REFERENCE
"MPLS-TP Identifiers Following ITU-T Conventions,
[RFC6923] Section 3"
SYNTAX OCTET STRING (SIZE (0|1..6))
MplsNodeId ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION
"The Node_ID is assigned within the scope of
the Global_ID/ICC_Operator_ID.
The value 0(or 0.0.0.0 in dotted decimal notation) is
reserved and MUST NOT be used.
When IPv4 addresses are in use, the value of this object
can be derived from the LSR's IPv4 loop back address.
When IPv6 addresses are in use, the value of this object
can be a 32-bit value unique within the scope of
a Global_ID.
Note that, when IP reach ability is not needed, the 32-bit
Node_ID is not required to have any association
with the IPv4 address space."
REFERENCE
"MPLS Transport Profile (MPLS-TP) Identifiers, [RFC6370]
Section 4"
SYNTAX Unsigned32 (0|1..4294967295)
-- MPLS-TC-EXT-STD-MIB module ends
END
11. MPLS Identifier MIB definitions
MPLS-ID-STD-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE
FROM SNMPv2-SMI -- [RFC2578]
MODULE-COMPLIANCE, OBJECT-GROUP
Venkatesan, et al. Expires May 08, 2014 [Page 25]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
FROM SNMPv2-CONF -- [RFC2580]
mplsStdMIB
FROM MPLS-TC-STD-MIB -- [RFC3811]
MplsGlobalId, MplsCcId, MplsIccId, MplsNodeId
FROM MPLS-TC-EXT-STD-MIB
;
mplsIdStdMIB MODULE-IDENTITY
LAST-UPDATED
"201311010000Z" -- November 01, 2013
ORGANIZATION
"Multiprotocol Label Switching (MPLS) Working Group"
CONTACT-INFO
"
Venkatesan Mahalingam
Dell Inc,
350 Holger way, San Jose, CA, USA
Email: venkat.mahalingams@gmail.com
Kannan KV Sampath
Redeem,
India
Email: kannankvs@gmail.com
Sam Aldrin
Huawei Technologies
2330 Central Express Way,
Santa Clara, CA 95051, USA
Email: aldrin.ietf@gmail.com
Thomas D. Nadeau
Juniper Networks
10 Technology Park Drive,
Westford, MA 01886
Email: tnadeau@juniper.net
"
DESCRIPTION
"Copyright (c) 2013 IETF Trust and the persons identified
as the document authors. All rights reserved.
This MIB module contains generic object definitions for
MPLS Traffic Engineering in transport networks."
-- Revision history.
Venkatesan, et al. Expires May 08, 2014 [Page 26]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
REVISION
"201311010000Z" -- November 01, 2013
DESCRIPTION
"This MIB modules defines the MIB objects for MPLS-TP
identifiers"
::= { mplsStdMIB xxx } -- xxx to be replaced with correct value
-- notifications
mplsIdNotifications OBJECT IDENTIFIER ::= { mplsIdStdMIB 0 }
-- tables, scalars
mplsIdObjects OBJECT IDENTIFIER ::= { mplsIdStdMIB 1 }
-- conformance
mplsIdConformance OBJECT IDENTIFIER ::= { mplsIdStdMIB 2 }
-- MPLS common objects
mplsIdGlobalId OBJECT-TYPE
SYNTAX MplsGlobalId
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object allows the operator to assign a unique
operator identifier also called MPLS-TP Global_ID.
If this value is used in mplsTunnelExtNodeConfigGlobalId
for mapping Global_ID::Node_ID with the local identifier
then this object value SHOULD NOT be changed."
::= { mplsIdObjects 1 }
mplsIdNodeId OBJECT-TYPE
SYNTAX MplsNodeId
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object allows the operator or service provider to
assign a unique MPLS-TP Node_ID.
The Node_ID is assigned within the scope of
the Global_ID/ICC_Operator_ID.
If this value is used in mplsTunnelExtNodeConfigNodeId
for mapping Global_ID::Node_ID with the local identifier
then this object value SHOULD NOT be changed.
If this value is used in mplsTunnelExtNodeConfigNodeId
for mapping ICC_Operator_ID::Node_ID with the local
identifier then this object value SHOULD NOT be changed."
::= { mplsIdObjects 2 }
Venkatesan, et al. Expires May 08, 2014 [Page 27]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
mplsIdCc OBJECT-TYPE
SYNTAX MplsCcId
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object allows the operator or service provider to
assign a unique Country Code (CC). Global uniqueness is
assured by concatenating the ICC with a
Country Code (CC).
If this value is used in mplsTunnelExtNodeConfigCcId
for mapping ICC_Operator_ID::Node_ID with the local
identifier then this object value SHOULD NOT be changed."
REFERENCE
"MPLS-TP Identifiers Following ITU-T Conventions,
[RFC6923] Section 3"
::= { mplsIdObjects 3 }
mplsIdIcc OBJECT-TYPE
SYNTAX MplsIccId
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object allows the operator or service provider to
assign a unique MPLS-TP ITU-T Carrier Code (ICC) to a
network. Together, the CC and the ICC form
the ICC_Operator_ID as CC::ICC.
If this value is used in mplsTunnelExtNodeConfigIccId
for mapping ICC_Operator_ID::Node_ID with the local
identifier then this object value SHOULD NOT be changed."
REFERENCE
"MPLS-TP Identifiers Following ITU-T Conventions,
[RFC6923] Section 3"
::= { mplsIdObjects 4 }
-- Module compliance.
mplsIdCompliances
OBJECT IDENTIFIER ::= { mplsIdConformance 1 }
mplsIdGroups
OBJECT IDENTIFIER ::= { mplsIdConformance 2 }
-- Compliance requirement for fully compliant implementations.
mplsIdModuleFullCompliance MODULE-COMPLIANCE
STATUS current
Venkatesan, et al. Expires May 08, 2014 [Page 28]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
DESCRIPTION
"Compliance statement for agents that provide full
support the MPLS-ID-STD-MIB module."
MODULE -- this module
-- The mandatory group has to be implemented by all
-- LSRs that originate/terminate MPLS-TP paths.
MANDATORY-GROUPS {
mplsIdScalarGroup
}
::= { mplsIdCompliances 1 }
-- Compliance requirement for read-only implementations.
mplsIdModuleReadOnlyCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"Compliance statement for agents that only provide
read-only support for the MPLS-ID-STD-MIB module."
MODULE -- this module
MANDATORY-GROUPS {
mplsIdScalarGroup
}
OBJECT mplsIdGlobalId
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsIdNodeId
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsIdIcc
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsIdCc
MIN-ACCESS read-only
DESCRIPTION
Venkatesan, et al. Expires May 08, 2014 [Page 29]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
"Write access is not required."
::= { mplsIdCompliances 2 }
-- Units of conformance.
mplsIdScalarGroup OBJECT-GROUP
OBJECTS { mplsIdGlobalId,
mplsIdNodeId,
mplsIdIcc,
mplsIdCc
}
STATUS current
DESCRIPTION
"Scalar object needed to implement MPLS TP path."
::= { mplsIdGroups 1 }
-- MPLS-ID-STD-MIB module ends
END
12. MPLS LSR Extension MIB definitions
MPLS-LSR-EXT-STD-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE
FROM SNMPv2-SMI -- [RFC2578]
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF -- [RFC2580]
mplsStdMIB
FROM MPLS-TC-STD-MIB -- [RFC3811]
RowPointer
FROM SNMPv2-TC -- [RFC2579]
mplsXCIndex, mplsXCInSegmentIndex, mplsXCOutSegmentIndex,
mplsInterfaceGroup, mplsInSegmentGroup, mplsOutSegmentGroup,
mplsXCGroup, mplsPerfGroup, mplsLsrNotificationGroup
FROM MPLS-LSR-STD-MIB; -- [RFC3813]
mplsLsrExtStdMIB MODULE-IDENTITY
LAST-UPDATED
"201311010000Z" -- November 01, 2013
ORGANIZATION
"Multiprotocol Label Switching (MPLS) Working Group"
CONTACT-INFO
"
Venkatesan Mahalingam
Dell Inc,
Venkatesan, et al. Expires May 08, 2014 [Page 30]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
350 Holger way, San Jose, CA, USA
Email: venkat.mahalingams@gmail.com
Kannan KV Sampath
Redeem,
India
Email: kannankvs@gmail.com
Sam Aldrin
Huawei Technologies
2330 Central Express Way,
Santa Clara, CA 95051, USA
Email: aldrin.ietf@gmail.com
Thomas D. Nadeau
Juniper Networks
10 Technology Park Drive, Westford, MA 01886
Email: tnadeau@juniper.net
"
DESCRIPTION
"Copyright (c) 2013 IETF Trust and the persons identified
as the document authors. All rights reserved.
This MIB module contains generic object definitions for
MPLS LSR in transport networks."
-- Revision history.
REVISION
"201311010000Z" -- November 01, 2013
DESCRIPTION
"MPLS LSR specific MIB objects extension"
::= { mplsStdMIB xxx } -- xxx to be replaced with correct value
-- notifications
mplsLsrExtNotifications OBJECT IDENTIFIER ::= { mplsLsrExtStdMIB 0 }
-- tables, scalars
mplsLsrExtObjects OBJECT IDENTIFIER
::= { mplsLsrExtStdMIB 1 }
-- conformance
Venkatesan, et al. Expires May 08, 2014 [Page 31]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
mplsLsrExtConformance OBJECT IDENTIFIER
::= { mplsLsrExtStdMIB 2 }
-- MPLS LSR common objects
mplsXCExtTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsXCExtEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table sparse augments the mplsXCTable of
MPLS-LSR-STD-MIB [RFC3813] to provide MPLS-TP specific
information about associated tunnel information"
REFERENCE
"1. Multiprotocol Label Switching (MPLS) Label Switching
Router (LSR) Management Information Base (MIB), RFC 3813."
::= { mplsLsrExtObjects 1 }
mplsXCExtEntry OBJECT-TYPE
SYNTAX MplsXCExtEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table extends the cross connect
information represented by an entry in
the mplsXCTable in MPLS-LSR-STD-MIB [RFC3813] through
a sparse augmentation. An entry can be created by
a network operator via SNMP SET commands, or in
response to signaling protocol events."
REFERENCE
"1. Multiprotocol Label Switching (MPLS) Label Switching
Router (LSR) Management Information Base (MIB), RFC 3813."
INDEX { mplsXCIndex, mplsXCInSegmentIndex,
mplsXCOutSegmentIndex }
::= { mplsXCExtTable 1 }
MplsXCExtEntry ::= SEQUENCE {
mplsXCExtTunnelPointer RowPointer,
mplsXCExtOppositeDirXCPtr RowPointer
}
mplsXCExtTunnelPointer OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-only
STATUS current
Venkatesan, et al. Expires May 08, 2014 [Page 32]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
DESCRIPTION
"This read-only object indicates the back pointer to
the tunnel entry segment.
The only valid value for Tunnel Pointer is
mplsTunnelTable entry."
REFERENCE
"1. Multiprotocol Label Switching (MPLS) Label Switching
Router (LSR) Management Information Base (MIB), RFC 3813."
::= { mplsXCExtEntry 1 }
mplsXCExtOppositeDirXCPtr OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object indicates the pointer to the opposite
direction XC entry. This object cannot be modified if
mplsXCRowStatus for the corresponding entry in the
mplsXCTable is active(1)."
REFERENCE
"1. Multiprotocol Label Switching (MPLS) Label Switching
Router (LSR) Management Information Base (MIB), RFC 3813."
::= { mplsXCExtEntry 2 }
mplsLsrExtCompliances
OBJECT IDENTIFIER ::= { mplsLsrExtConformance 1 }
mplsLsrExtGroups
OBJECT IDENTIFIER ::= { mplsLsrExtConformance 2 }
-- Compliance requirement for fully compliant implementations.
mplsLsrExtModuleFullCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"Compliance statement for agents that provide full support
for MPLS-LSR-EXT-STD-MIB.
The mandatory group has to be implemented by all LSRs
that originate, terminate, or act as transit for
TE-LSPs/tunnels.
In addition, depending on the type of tunnels supported,
other groups become mandatory as explained below."
MODULE MPLS-LSR-STD-MIB -- The MPLS-LSR-STD-MIB, RFC3813
MANDATORY-GROUPS {
mplsInSegmentGroup,
mplsOutSegmentGroup,
Venkatesan, et al. Expires May 08, 2014 [Page 33]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
mplsXCGroup,
mplsPerfGroup,
mplsLsrNotificationGroup
}
MODULE -- this module
MANDATORY-GROUPS {
mplsXCExtGroup
}
::= { mplsLsrExtCompliances 1 }
-- Compliance requirement for implementations that provide
-- read-only access.
mplsLsrExtModuleReadOnlyCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"Compliance requirement for implementations that only
provide read-only support for MPLS-LSR-EXT-STD-MIB.
Such devices can then be monitored but cannot be
configured using this MIB module."
MODULE MPLS-LSR-STD-MIB
MANDATORY-GROUPS {
mplsInterfaceGroup,
mplsInSegmentGroup,
mplsOutSegmentGroup,
mplsPerfGroup
}
MODULE -- this module
GROUP mplsXCExtReadOnlyObjectsGroup
DESCRIPTION
"This group is mandatory for devices which support
Opposite direction XC configuration of tunnels."
-- mplsXCExtTable
OBJECT mplsXCExtOppositeDirXCPtr
MIN-ACCESS read-only
DESCRIPTION
Venkatesan, et al. Expires May 08, 2014 [Page 34]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
"Write access is not required.
This object indicates the pointer to the opposite
direction XC entry. The only valid value for XC
Pointer is mplsXCTable entry."
::= { mplsLsrExtCompliances 2 }
-- Units of conformance.
mplsXCExtGroup OBJECT-GROUP
OBJECTS {
mplsXCExtTunnelPointer,
mplsXCExtOppositeDirXCPtr
}
STATUS current
DESCRIPTION
"This object should be supported in order to access
the tunnel entry from XC entry."
::= { mplsLsrExtGroups 1 }
mplsXCExtReadOnlyObjectsGroup OBJECT-GROUP
OBJECTS {
mplsXCExtTunnelPointer,
mplsXCExtOppositeDirXCPtr
}
STATUS current
DESCRIPTION
"This Object is needed to associate the opposite direction
(forward/reverse) XC entry."
::= { mplsLsrExtGroups 2 }
-- MPLS-LSR-EXT-STD-MIB module ends
END
13. MPLS Tunnel Extension MIB definitions
MPLS-TE-EXT-STD-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, Counter32,
Counter64, zeroDotZero
FROM SNMPv2-SMI -- [RFC2578]
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF -- [RFC2580]
TruthValue, RowStatus, RowPointer, StorageType
FROM SNMPv2-TC -- [RFC2579]
Venkatesan, et al. Expires May 08, 2014 [Page 35]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
MplsGlobalId, MplsNodeId, MplsCcId, MplsIccId
FROM MPLS-TC-EXT-STD-MIB
mplsStdMIB, MplsTunnelIndex, MplsTunnelInstanceIndex,
MplsExtendedTunnelId
FROM MPLS-TC-STD-MIB -- [RFC3811]
mplsTunnelIndex, mplsTunnelInstance, mplsTunnelIngressLSRId,
mplsTunnelEgressLSRId
FROM MPLS-TE-STD-MIB -- [RFC3812]
;
mplsTeExtStdMIB MODULE-IDENTITY
LAST-UPDATED
"201311010000Z" -- November 01, 2013
ORGANIZATION
"Multiprotocol Label Switching (MPLS) Working Group"
CONTACT-INFO
"
Venkatesan Mahalingam
Dell Inc,
350 Holger way, San Jose, CA, USA
Email: venkat.mahalingams@gmail.com
Kannan KV Sampath
Redeem,
India
Email: kannankvs@gmail.com
Sam Aldrin
Huawei Technologies
2330 Central Express Way,
Santa Clara, CA 95051, USA
Email: aldrin.ietf@gmail.com
Thomas D. Nadeau
Juniper Networks
10 Technology Park Drive, Westford, MA 01886
Email: tnadeau@juniper.net
"
DESCRIPTION
"Copyright (c) 2013 IETF Trust and the persons identified
as the document authors. All rights reserved.
This MIB module contains generic object definitions for
MPLS Traffic Engineering in transport networks."
-- Revision history.
Venkatesan, et al. Expires May 08, 2014 [Page 36]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
REVISION
"201311010000Z" -- November 01, 2013
DESCRIPTION
"MPLS TE MIB objects extension"
::= { mplsStdMIB xxx } -- xxx to be replaced
-- with correct value
-- Top level components of this MIB module.
-- notifications
mplsTeExtNotifications OBJECT IDENTIFIER ::= { mplsTeExtStdMIB 0 }
-- tables, scalars
mplsTeExtObjects OBJECT IDENTIFIER
::= { mplsTeExtStdMIB 1 }
-- conformance
mplsTeExtConformance OBJECT IDENTIFIER
::= { mplsTeExtStdMIB 2 }
-- Start of MPLS Transport Profile Node configuration table
mplsTunnelExtNodeConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsTunnelExtNodeConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table allows the operator to map a node or
LSR Identifier (IP compatible [Global_ID::Node_ID] or
ICC based [ICC_Operator_ID::Node_ID]) with a local
identifier.
This table is created to reuse the existing
mplsTunnelTable for MPLS based transport network
tunnels also.
Since the MPLS tunnel's Ingress/Egress LSR identifiers'
size (Unsigned32) value is not compatible for
MPLS-TP tunnel i.e. Global_ID::Node_ID of size 8 bytes and
ICC_Operator_ID::Node_ID of size 12 bytes, there exists a
need to map the Global_ID::Node_ID or ICC_Operator_ID::Node_ID
with the local identifier of size 4 bytes (Unsigned32) value
in order to index (Ingress/Egress LSR identifier)
the existing mplsTunnelTable."
::= { mplsTeExtObjects 1 }
Venkatesan, et al. Expires May 08, 2014 [Page 37]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
mplsTunnelExtNodeConfigEntry OBJECT-TYPE
SYNTAX MplsTunnelExtNodeConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents a mapping
identification for the operator or service provider
with node or LSR.
As per [RFC6370], IP compatible mapping is represented
as Global_ID::Node_ID.
As per [RFC6923], the CC and the ICC form the ICC_Operator_ID
as CC::ICC and ICC compatible mapping is represented
as ICC_Operator_ID::Node_ID.
Note: Each entry in this table should have a unique
[Global_ID and Node_ID] or [CC::ICC and Node_ID] combination."
INDEX { mplsTunnelExtNodeConfigLocalId }
::= { mplsTunnelExtNodeConfigTable 1 }
MplsTunnelExtNodeConfigEntry ::= SEQUENCE {
mplsTunnelExtNodeConfigLocalId MplsExtendedTunnelId,
mplsTunnelExtNodeConfigGlobalId MplsGlobalId,
mplsTunnelExtNodeConfigCcId MplsCcId,
mplsTunnelExtNodeConfigIccId MplsIccId,
mplsTunnelExtNodeConfigNodeId MplsNodeId,
mplsTunnelExtNodeConfigIccValid TruthValue,
mplsTunnelExtNodeConfigStorageType StorageType,
mplsTunnelExtNodeConfigRowStatus RowStatus
}
mplsTunnelExtNodeConfigLocalId OBJECT-TYPE
SYNTAX MplsExtendedTunnelId
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object is used in accommodating the bigger
size Global_ID::Node_ID and/or the ICC_Operator_ID::Node_ID
with lower size LSR identifier in order to index
the mplsTunnelTable.
The Local Identifier is configured between 0 and 16777215,
as valid IP address range starts from 16777216(01.00.00.00).
This range is chosen to identify the mplsTunnelTable's
Ingress/Egress LSR-id is IP address or Local identifier,
if the configured range is not IP address, operator is
Venkatesan, et al. Expires May 08, 2014 [Page 38]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
expected to retrieve the complete information
(Global_ID::Node_ID or ICC_Operator_ID::Node_ID) from
mplsTunnelExtNodeConfigTable.
This way, existing mplsTunnelTable is reused for
bidirectional tunnel extensions for MPLS based transport
networks.
This Local Identifier allows the operator to assign
a unique identifier to map Global_ID::Node_ID and/or
ICC_Operator_ID::Node_ID. As this Local Identifier is unique
within the node and the same syntax of this object can be
used for MPLS TE tunnel also, it is up to the operator/local
management entity to choose the non-conflicting value for
indexing the MPLS and MPLS-TP tunnel entries."
::= { mplsTunnelExtNodeConfigEntry 1 }
mplsTunnelExtNodeConfigGlobalId OBJECT-TYPE
SYNTAX MplsGlobalId
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object indicates the Global Operator Identifier.
This object has no meaning when
mplsTunnelExtNodeConfigIccValid is set true."
REFERENCE
"MPLS Transport Profile (MPLS-TP) Identifiers [RFC6370]
Section 3."
::= { mplsTunnelExtNodeConfigEntry 2 }
mplsTunnelExtNodeConfigCcId OBJECT-TYPE
SYNTAX MplsCcId
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object allows the operator or service provider to
configure a unique MPLS-TP ITU-T Country Code (CC)
either for Ingress ID or Egress ID.
This object has no meaning when
mplsTunnelExtNodeConfigIccValid is set false."
REFERENCE
"MPLS-TP Identifiers Following ITU-T Conventions,
[RFC6923] Section 3"
::= { mplsTunnelExtNodeConfigEntry 3 }
mplsTunnelExtNodeConfigIccId OBJECT-TYPE
SYNTAX MplsIccId
Venkatesan, et al. Expires May 08, 2014 [Page 39]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object allows the operator or service provider to
configure a unique MPLS-TP ITU-T Carrier Code (ICC)
either for Ingress ID or Egress ID.
This object has no meaning when
mplsTunnelExtNodeConfigIccValid is set false."
REFERENCE
"MPLS-TP Identifiers Following ITU-T Conventions,
[RFC6923] Section 3"
::= { mplsTunnelExtNodeConfigEntry 4 }
mplsTunnelExtNodeConfigNodeId OBJECT-TYPE
SYNTAX MplsNodeId
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object indicates the Node_ID within the scope
of a Global_ID or ICC_Operator_ID."
REFERENCE
"MPLS Transport Profile (MPLS-TP) Identifiers [RFC6370]
Section 4."
::= { mplsTunnelExtNodeConfigEntry 5 }
mplsTunnelExtNodeConfigIccValid OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Denotes whether or not this entry uses
mplsTunnelExtNodeConfigCcId,
mplsTunnelExtNodeConfigIccId and
mplsTunnelExtNodeConfigNodeId for mapping
the ICC based identifiers with the local identifier.
Note that if this variable is set to false then the
mplsTunnelExtNodeConfigGlobalId and
mplsTunnelExtNodeConfigNodeId objects should have
the valid information."
DEFVAL { false }
::= { mplsTunnelExtNodeConfigEntry 6 }
mplsTunnelExtNodeConfigStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
Venkatesan, et al. Expires May 08, 2014 [Page 40]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
"This variable indicates the storage type for this
object.
Conceptual rows having the value 'permanent'
need not allow write-access to any columnar
objects in the row."
DEFVAL { volatile }
::= { mplsTunnelExtNodeConfigEntry 7 }
mplsTunnelExtNodeConfigRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object allows the operator to create, modify,
and/or delete a row in this table."
::= { mplsTunnelExtNodeConfigEntry 8 }
-- End of MPLS Transport Profile Node configuration table
-- Start of MPLS Transport Profile Node IP compatible
-- mapping table
mplsTunnelExtNodeIpMapTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsTunnelExtNodeIpMapEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This read-only table allows the operator to retrieve
the local identifier for a given Global_ID::Node_ID in an IP
compatible operator environment.
This table MAY be used in on-demand and/or proactive
OAM operations to get the Ingress/Egress LSR identifier
(Local Identifier) from Src-Global_Node_ID
or Dst-Global_Node_ID and the Ingress and Egress LSR
identifiers are used to retrieve the tunnel entry.
This table returns nothing when the associated entry
is not defined in mplsTunnelExtNodeConfigTable."
::= { mplsTeExtObjects 2 }
mplsTunnelExtNodeIpMapEntry OBJECT-TYPE
SYNTAX MplsTunnelExtNodeIpMapEntry
MAX-ACCESS not-accessible
STATUS current
Venkatesan, et al. Expires May 08, 2014 [Page 41]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
DESCRIPTION
"An entry in this table represents a mapping of
Global_ID::Node_ID with the local identifier.
An entry in this table is created automatically when
the Local identifier is associated with Global_ID and
Node_Id in the mplsTunnelExtNodeConfigTable.
Note: Each entry in this table should have a unique
Global_ID and Node_ID combination."
INDEX { mplsTunnelExtNodeIpMapGlobalId,
mplsTunnelExtNodeIpMapNodeId
}
::= { mplsTunnelExtNodeIpMapTable 1 }
MplsTunnelExtNodeIpMapEntry ::= SEQUENCE {
mplsTunnelExtNodeIpMapGlobalId MplsGlobalId,
mplsTunnelExtNodeIpMapNodeId MplsNodeId,
mplsTunnelExtNodeIpMapLocalId MplsExtendedTunnelId
}
mplsTunnelExtNodeIpMapGlobalId OBJECT-TYPE
SYNTAX MplsGlobalId
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object indicates the Global_ID."
::= { mplsTunnelExtNodeIpMapEntry 1 }
mplsTunnelExtNodeIpMapNodeId OBJECT-TYPE
SYNTAX MplsNodeId
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object indicates the Node_ID within the
operator."
::= { mplsTunnelExtNodeIpMapEntry 2 }
mplsTunnelExtNodeIpMapLocalId OBJECT-TYPE
SYNTAX MplsExtendedTunnelId
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains an IP compatible local identifier
which is defined in mplsTunnelExtNodeConfigTable."
::= { mplsTunnelExtNodeIpMapEntry 3 }
Venkatesan, et al. Expires May 08, 2014 [Page 42]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
-- End MPLS Transport Profile Node IP compatible table
-- Start of MPLS Transport Profile Node ICC based table
mplsTunnelExtNodeIccMapTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsTunnelExtNodeIccMapEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This read-only table allows the operator to retrieve
the local identifier for a given ICC_Operator_ID::Node_ID
in an ICC operator environment.
This table MAY be used in on-demand and/or proactive
OAM operations to get the Ingress/Egress LSR
identifier (Local Identifier) from Src-ICC
or Dst-ICC and the Ingress and Egress LSR
identifiers are used to retrieve the tunnel entry.
This table returns nothing when the associated entry
is not defined in mplsTunnelExtNodeConfigTable."
::= { mplsTeExtObjects 3 }
mplsTunnelExtNodeIccMapEntry OBJECT-TYPE
SYNTAX MplsTunnelExtNodeIccMapEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents a mapping of
ICC_Operator_ID::Node_ID with the local identifier.
An entry in this table is created automatically when
the Local identifier is associated with
ICC_Operator_ID::Node_ID in
the mplsTunnelExtNodeConfigTable."
INDEX { mplsTunnelExtNodeIccMapCcId,
mplsTunnelExtNodeIccMapIccId,
mplsTunnelExtNodeIccMapNodeId }
::= { mplsTunnelExtNodeIccMapTable 1 }
MplsTunnelExtNodeIccMapEntry ::= SEQUENCE {
mplsTunnelExtNodeIccMapCcId MplsCcId,
mplsTunnelExtNodeIccMapIccId MplsIccId,
mplsTunnelExtNodeIccMapNodeId MplsNodeId,
mplsTunnelExtNodeIccMapLocalId MplsExtendedTunnelId
}
mplsTunnelExtNodeIccMapCcId OBJECT-TYPE
Venkatesan, et al. Expires May 08, 2014 [Page 43]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
SYNTAX MplsCcId
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object allows the operator or service provider to
configure a unique MPLS-TP ITU-T Country Code (CC)
either for Ingress or Egress LSR ID.
The CC is a string of two alphabetic characters
represented with upper case letters (i.e., A-Z)."
::= { mplsTunnelExtNodeIccMapEntry 1 }
mplsTunnelExtNodeIccMapIccId OBJECT-TYPE
SYNTAX MplsIccId
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object allows the operator or service provider
to configure a unique MPLS-TP ITU-T Carrier
Code (ICC) either for Ingress or Egress LSR ID.
The ICC is a string of one to six characters, each
character being either alphabetic (i.e. A-Z) or
numeric (i.e. 0-9) characters. Alphabetic characters
in the ICC should be represented with upper case
letters."
::= { mplsTunnelExtNodeIccMapEntry 2 }
mplsTunnelExtNodeIccMapNodeId OBJECT-TYPE
SYNTAX MplsNodeId
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object indicates the Node_ID within the
ICC based operator."
::= { mplsTunnelExtNodeIccMapEntry 3}
mplsTunnelExtNodeIccMapLocalId OBJECT-TYPE
SYNTAX MplsExtendedTunnelId
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains an ICC based local identifier
which is defined in mplsTunnelExtNodeConfigTable."
::= { mplsTunnelExtNodeIccMapEntry 4 }
-- End MPLS Transport Profile Node ICC based table
Venkatesan, et al. Expires May 08, 2014 [Page 44]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
-- Start of MPLS Tunnel table extension
mplsTunnelExtTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsTunnelExtEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table represents extensions to mplsTunnelTable
in order to support MPLS-TP tunnels.
As per MPLS-TP Identifiers [RFC6370], LSP_ID for IP based
co-routed bidirectional tunnel,
A1-{Global_ID::Node_ID::Tunnel_Num}::Z9-{Global_ID::
Node_ID::Tunnel_Num}::LSP_Num
LSP_ID for IP based associated bidirectional tunnel,
A1-{Global_ID::Node_ID::Tunnel_Num::LSP_Num}::
Z9-{Global_ID::Node_ID::Tunnel_Num::LSP_Num}
mplsTunnelTable is reused for forming the LSP_ID
as follows,
Source Tunnel_Num is mapped with mplsTunnelIndex,
Source Node_ID is mapped with
mplsTunnelIngressLSRId, Destination Node_ID is
mapped with mplsTunnelEgressLSRId LSP_Num is mapped with
mplsTunnelInstance.
Source Global_ID::Node_ID and/or ICC_Operator_ID::Node_ID and
Destination Global_ID::Node_ID and/or ICC_Operator_ID::Node-ID
are maintained in the mplsTunnelExtNodeConfigTable and
mplsTunnelExtNodeConfigLocalId is used to create an entry
in mplsTunnelTable."
REFERENCE
"MPLS Transport Profile (MPLS-TP) Identifiers [RFC6370]."
::= { mplsTeExtObjects 4 }
mplsTunnelExtEntry OBJECT-TYPE
SYNTAX MplsTunnelExtEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents MPLS-TP
specific additional tunnel configurations."
INDEX {
mplsTunnelIndex,
Venkatesan, et al. Expires May 08, 2014 [Page 45]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
mplsTunnelInstance,
mplsTunnelIngressLSRId,
mplsTunnelEgressLSRId
}
::= { mplsTunnelExtTable 1 }
MplsTunnelExtEntry ::= SEQUENCE {
mplsTunnelExtOppositeDirPtr RowPointer,
mplsTunnelExtOppositeDirTnlValid TruthValue,
mplsTunnelExtDestTnlIndex MplsTunnelIndex,
mplsTunnelExtDestTnlLspIndex MplsTunnelInstanceIndex,
mplsTunnelExtDestTnlValid TruthValue,
mplsTunnelExtIngressLSRLocalIdValid TruthValue,
mplsTunnelExtEgressLSRLocalIdValid TruthValue
}
mplsTunnelExtOppositeDirPtr OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is applicable only for the bidirectional
tunnel that has the forward and reverse LSPs in the
same tunnel or in the different tunnels.
This object holds the opposite direction tunnel entry
if the bidirectional tunnel is setup by configuring two
tunnel entries in mplsTunnelTable.
The value of zeroDotZero indicates single tunnel entry
is used for bidirectional tunnel setup."
DEFVAL { zeroDotZero }
::= { mplsTunnelExtEntry 1 }
mplsTunnelExtOppositeDirTnlValid OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Denotes whether or not this tunnel uses
mplsTunnelExtOppositeDirPtr for identifying the opposite
direction tunnel information. Note that if this variable
is set to true then the mplsTunnelExtOppositeDirPtr should
point to the first accessible row of the opposite
direction tunnel."
DEFVAL { false }
::= { mplsTunnelExtEntry 2 }
Venkatesan, et al. Expires May 08, 2014 [Page 46]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
mplsTunnelExtDestTnlIndex OBJECT-TYPE
SYNTAX MplsTunnelIndex
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is applicable only for the bidirectional
tunnel that has the forward and reverse LSPs in the
same tunnel or in the different tunnels.
This object holds the same value as that of the
mplsTunnelIndex of mplsTunnelEntry if the forward and
reverse LSPs are in the same tunnel. Otherwise,
this object holds the value of the other direction
associated LSP's mplsTunnelIndex from a different
tunnel.
The values of this object and the
mplsTunnelExtDestTnlLspIndex object together can be used
to identify an opposite direction LSP i.e. if the
mplsTunnelIndex and mplsTunnelInstance hold the value
for forward LSP, this object and
mplsTunnelExtDestTnlLspIndex can be used to retrieve
the reverse direction LSP and vice versa.
This object and mplsTunnelExtDestTnlLspIndex values
provide the first two indices of tunnel entry and
the remaining indices can be derived as follows,
if both the forward and reverse LSPs are present in
the same tunnel, the opposite direction LSP's Ingress
and Egress Identifier will be same for both the LSPs,
else the Ingress and Egress Identifiers should be
swapped in order to index the other direction tunnel."
::= { mplsTunnelExtEntry 3 }
mplsTunnelExtDestTnlLspIndex OBJECT-TYPE
SYNTAX MplsTunnelInstanceIndex
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is applicable only for the bidirectional
tunnel that has the forward and reverse LSPs in the
same tunnel or in the different tunnels.
This object should contain different value if both the
forward and reverse LSPs present in the same tunnel.
Venkatesan, et al. Expires May 08, 2014 [Page 47]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
This object can contain same value or different values
if the forward and reverse LSPs present in the different
tunnels."
::= { mplsTunnelExtEntry 4 }
mplsTunnelExtDestTnlValid OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Denotes whether or not this tunnel uses
mplsTunnelExtDestTnlIndex and
mplsTunnelExtDestTnlLspIndex for identifying
the opposite direction tunnel information. Note that if
this variable is set to true then the
mplsTunnelExtDestTnlIndex and
mplsTunnelExtDestTnlLspIndex objects should have
the valid opposite direction tunnel indices."
DEFVAL { false }
::= { mplsTunnelExtEntry 5 }
mplsTunnelExtIngressLSRLocalIdValid OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object denotes whether the mplsTunnelIngressLSRId
contains the local value, which is used to reference
the complete Ingress Global_ID::Node_ID or ICC_Operator_ID
from the mplsTunnelExtNodeConfigTable.
If this object is set to FALSE, mplsTunnelExtNodeConfigTable
will not contain an entry to reference local identifier with
Global_ID::Node_ID or ICC_Operator_ID::Node_ID value.
This object is set to FALSE for legacy implementations like
MPLS TE tunnels where mplsTunnelIngressId itself provides
complete Ingress LSRId."
REFERENCE
"MPLS-TE-STD-MIB [RFC3812], Section 11.
mplsTunnelIngressLSRId object in mplsTunnelTable."
DEFVAL { false }
::= { mplsTunnelExtEntry 6 }
mplsTunnelExtEgressLSRLocalIdValid OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
Venkatesan, et al. Expires May 08, 2014 [Page 48]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
STATUS current
DESCRIPTION
"This object denotes whether the mplsTunnelEgressLSRId
contains the local value, which is used to reference
the complete Egress Global_ID::Node_ID or
ICC_Operator_ID::Node_ID from
the mplsTunnelExtNodeConfigTable.
If this object is set to FALSE, mplsTunnelExtNodeConfigTable
will not contain an entry to reference local identifier with
Global_ID::Node_ID or ICC_Operator_ID::Node_ID value.
This object is set to FALSE for legacy implementations like
MPLS TE tunnels where mplsTunnelEgressId itself provides
complete Egress LSRId."
REFERENCE
"MPLS-TE-STD-MIB [RFC3812], Section 11.
mplsTunnelEgressLSRId object in mplsTunnelTable."
DEFVAL { false }
::= { mplsTunnelExtEntry 7 }
-- End of MPLS Tunnel table extension
mplsTunnelExtReversePerfTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsTunnelExtReversePerfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table extends the mplsTunnelTable to provide
per-tunnel packet performance information for the reverse
direction of a bidirectional tunnel. It can be seen as
supplementing the mplsTunnelPerfTable, which augments the
mplsTunnelTable."
REFERENCE
"1. Multiprotocol Label Switching (MPLS) Traffic
Engineering (TE)Management Information Base (MIB),
RFC 3812."
::= { mplsTeExtObjects 5 }
mplsTunnelExtReversePerfEntry OBJECT-TYPE
SYNTAX MplsTunnelExtReversePerfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table is created by the LSR for every
bidirectional MPLS tunnel where packets are visible to the
LSR."
INDEX {
mplsTunnelIndex,
Venkatesan, et al. Expires May 08, 2014 [Page 49]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
mplsTunnelInstance,
mplsTunnelIngressLSRId,
mplsTunnelEgressLSRId
}
::= { mplsTunnelExtReversePerfTable 1 }
MplsTunnelExtReversePerfEntry ::= SEQUENCE {
mplsTunnelExtReversePerfPackets Counter32,
mplsTunnelExtReversePerfHCPackets Counter64,
mplsTunnelExtReversePerfErrors Counter32,
mplsTunnelExtReversePerfBytes Counter32,
mplsTunnelExtReversePerfHCBytes Counter64
}
mplsTunnelExtReversePerfPackets OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of packets forwarded on the tunnel in the reverse
direction if it is bidirectional.
This object represents the 32-bit value of the least
significant part of the 64-bit value if both
mplsTunnelExtReversePerfHCPackets and this object
are returned."
::= { mplsTunnelExtReversePerfEntry 1 }
mplsTunnelExtReversePerfHCPackets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"High-capacity counter for number of packets forwarded on
the tunnel in the reverse direction if it is
bidirectional."
::= { mplsTunnelExtReversePerfEntry 2 }
mplsTunnelExtReversePerfErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of errored packets received on the tunnel in
the reverse direction if it is bidirectional."
::= { mplsTunnelExtReversePerfEntry 3 }
Venkatesan, et al. Expires May 08, 2014 [Page 50]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
mplsTunnelExtReversePerfBytes OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of bytes forwarded on the tunnel in the reverse
direction if it is bidirectional.
This object represents the 32-bit value of the least
significant part of the 64-bit value if both
mplsTunnelExtReversePerfHCBytes and this object are
returned."
::= { mplsTunnelExtReversePerfEntry 4 }
mplsTunnelExtReversePerfHCBytes OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"High-capacity counter for number of bytes forwarded on the
tunnel in the reverse direction if it is bidirectional."
::= { mplsTunnelExtReversePerfEntry 5 }
-- Module compliance.
mplsTeExtCompliances
OBJECT IDENTIFIER ::= { mplsTeExtConformance 1 }
mplsTeExtGroups
OBJECT IDENTIFIER ::= { mplsTeExtConformance 2 }
-- Compliance requirement for fully compliant implementations.
mplsTeExtModuleFullCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"Compliance statement for agents that provide full
support the MPLS-TE-EXT-STD-MIB module."
MODULE -- this module
-- The mandatory group has to be implemented by all
-- LSRs that originate/terminate MPLS-TP tunnels.
-- In addition, depending on the type of tunnels
-- supported, other groups become mandatory as
-- explained below.
Venkatesan, et al. Expires May 08, 2014 [Page 51]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
MANDATORY-GROUPS {
mplsTunnelExtGroup
}
::= { mplsTeExtCompliances 1 }
-- Compliance requirement for read-only implementations.
mplsTeExtModuleReadOnlyCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"Compliance statement for agents that only provide
read-only support for MPLS-TE-EXT-STD-MIB module."
MODULE -- this module
MANDATORY-GROUPS {
mplsTunnelExtGroup
}
GROUP mplsTunnelExtIpOperatorGroup
DESCRIPTION
"This group is mandatory for devices which support
configuration of IP based identifier tunnels."
GROUP mplsTunnelExtIccOperatorGroup
DESCRIPTION
"This group is mandatory for devices which support
configuration of ICC based tunnels."
-- mplsTunnelExtTable
OBJECT mplsTunnelExtOppositeDirPtr
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelExtOppositeDirTnlValid
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelExtDestTnlIndex
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelExtDestTnlLspIndex
Venkatesan, et al. Expires May 08, 2014 [Page 52]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelExtDestTnlValid
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelExtIngressLSRLocalIdValid
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelExtEgressLSRLocalIdValid
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelExtNodeConfigGlobalId
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelExtNodeConfigNodeId
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelExtNodeConfigStorageType
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelExtNodeConfigRowStatus
SYNTAX RowStatus { active(1) }
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelExtNodeConfigCcId
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsTunnelExtNodeConfigIccId
MIN-ACCESS read-only
DESCRIPTION
Venkatesan, et al. Expires May 08, 2014 [Page 53]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
"Write access is not required."
OBJECT mplsTunnelExtNodeConfigIccValid
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
::= { mplsTeExtCompliances 2 }
-- Units of conformance.
mplsTunnelExtGroup OBJECT-GROUP
OBJECTS {
mplsTunnelExtOppositeDirPtr,
mplsTunnelExtOppositeDirTnlValid,
mplsTunnelExtDestTnlIndex,
mplsTunnelExtDestTnlLspIndex,
mplsTunnelExtDestTnlValid,
mplsTunnelExtIngressLSRLocalIdValid,
mplsTunnelExtEgressLSRLocalIdValid,
mplsTunnelExtReversePerfPackets,
mplsTunnelExtReversePerfHCPackets,
mplsTunnelExtReversePerfErrors,
mplsTunnelExtReversePerfBytes,
mplsTunnelExtReversePerfHCBytes
}
STATUS current
DESCRIPTION
"Necessary, but not sufficient, set of objects to
implement tunnels. In addition, depending on the
operating environment, the following groups are
mandatory."
::= { mplsTeExtGroups 1 }
mplsTunnelExtIpOperatorGroup OBJECT-GROUP
OBJECTS { mplsTunnelExtNodeConfigGlobalId,
mplsTunnelExtNodeConfigNodeId,
mplsTunnelExtNodeIpMapLocalId,
mplsTunnelExtNodeConfigStorageType,
mplsTunnelExtNodeConfigRowStatus
}
STATUS current
DESCRIPTION
"Object(s) needed to implement IP compatible tunnels."
::= { mplsTeExtGroups 2 }
Venkatesan, et al. Expires May 08, 2014 [Page 54]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
mplsTunnelExtIccOperatorGroup OBJECT-GROUP
OBJECTS { mplsTunnelExtNodeConfigCcId,
mplsTunnelExtNodeConfigIccId,
mplsTunnelExtNodeConfigNodeId,
mplsTunnelExtNodeConfigIccValid,
mplsTunnelExtNodeIccMapLocalId,
mplsTunnelExtNodeConfigStorageType,
mplsTunnelExtNodeConfigRowStatus
}
STATUS current
DESCRIPTION
"Object(s) needed to implement ICC based tunnels."
::= { mplsTeExtGroups 3 }
-- MPLS-TE-EXT-STD-MIB module ends
END
14. Security Consideration
It is clear that this MIB module is potentially useful for the
monitoring of MPLS TE tunnels. This MIB module can also be used for
the configuration of certain objects, and anything that can be
configured can be incorrectly configured, with potentially disastrous
results.
There are a number of management objects defined in this MIB module
with a MAX-ACCESS clause of read-write. Such objects may be
considered sensitive or vulnerable in some network environments. The
support for SET operations in a non-secure environment without proper
protection can have a negative effect on network operations. These
are the tables and objects and their sensitivity/vulnerability:
- the tables specified in [RFC3812], [RFC3813] and this document
MIB tables mplsTunnelExtNodeConfigTable, mplsTunnelExtTable and
mplsXCExtTable collectively contain objects to provision MPLS-TP
tunnels, tunnel hops, and tunnel resources.
Unauthorized access to objects in these tables, could result in
disruption of traffic on the network. This is especially true if
a tunnel has been established. The use of stronger mechanisms,
such as SNMPv3 security, should be considered where possible.
Specifically, SNMPv3 VACM and USM MUST be used with any v3 agent
which implements this MIB. Administrators should consider whether
read access to these objects should be allowed, since read access
may be undesirable under certain circumstances.
Some of the readable objects in this MIB module (i.e., objects
with a MAX-ACCESS other than not-accessible) may be considered
sensitive or vulnerable in some network environments.
Venkatesan, et al. Expires May 08, 2014 [Page 55]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
It is thus important to control even GET and/or NOTIFY access to
these objects and possibly to even encrypt the values of these
objects when sending them over the network via SNMP. These are
the tables and objects and their sensitivity/vulnerability:
- the tables specified in [RFC3812], [RFC3813] and this document
MIB tables mplsTunnelExtNodeConfigTable, mplsTunnelExtTable,
mplsXCExtTable and mplsTunnelExtReversePerfTable collectively
show the MPLS-TP tunnel network topology and its performance
characteristics. If an Administrator does not want to reveal
this information, then these tables should be considered
sensitive/vulnerable.
SNMP versions prior to SNMPv3 did not include adequate security.
Even if the network itself is secure (for example by using IPsec),
even then, there is no control as to who on the secure network is
allowed to access and GET/SET (read/change/create/delete)
the objects in this MIB module.
It is recommended that implementers consider the security features as
provided by the SNMPv3 framework (see [RFC3410], section 8),
including full supports for the SNMPv3 cryptographic mechanisms (for
authentication and privacy).
Further, deployment of SNMP versions prior to SNMPv3 is not
recommended. Instead, it is recommended to deploy SNMPv3 and to
enable cryptographic security. It is then a customer/operator
responsibility to ensure that the SNMP entity giving access to an
instance of this MIB module is properly configured to give
access to the objects only to those principles (users) that
have legitimate rights to indeed GET or SET (change/create/delete)
them.
15. IANA Considerations
As described in [RFC4221], [RFC6639] and as requested in the MPLS-TC-
STD-MIB [RFC3811], MPLS related standards track MIB modules should be
rooted under the mplsStdMIB subtree. There are 4 MPLS MIB Modules
contained in this document, each of the following "IANA
Considerations" subsections requests IANA for a new assignment under
the mplsStdMIB subtree. New assignments can only be made via a
Standards Action as specified in [RFC5226].
15.1. IANA Considerations for MPLS-TC-EXT-STD-MIB
IANA is requested to assign an OID { mplsStdMIB OID } to the MPLS-TC-
EXT-STD-MIB module specified in this document.
Venkatesan, et al. Expires May 08, 2014 [Page 56]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
15.2. IANA Considerations for MPLS-ID-STD-MIB
IANA is requested to assign an OID { mplsStdMIB OID } to the MPLS-ID-
STD-MIB module specified in this document.
15.3. IANA Considerations for MPLS-LSR-EXT-STD-MIB
IANA is requested to assign an OID { mplsStdMIB OID } to the MPLS-
LSR-EXT-STD-MIB module specified in this document.
15.4. IANA Considerations for MPLS-TE-EXT-STD-MIB
IANA is requested to assign an OID { mplsStdMIB OID } to the MPLS-TE-
EXT-STD-MIB module specified in this document.
16. References
16.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2578] McCloghrie, K., Perkins, D., and J. Schoenwaelder,
"Structure of Management Information Version 2 (SMIv2)",
STD 58, RFC 2578, April 1999.
[RFC2579] McCloghrie, K., Perkins, D., and J. Schoenwaelder,
"Textual Conventions for SMIv2", STD 58, RFC 2579, April
1999.
[RFC2580] McCloghrie, K., Perkins, D., and J. Schoenwaelder,
"Conformance Statements for SMIv2", STD 58, RFC 2580,
April 1999.
[RFC3031] Rosen, E., Viswanathan, A., and R. Callon, "Multiprotocol
Label Switching Architecture", RFC 3031, January 2001.
16.2. Informative References
[RFC3410] J. Case, R. Mundy, D. pertain, B.Stewart, "Introduction
and Applicability Statement for Internet Standard
Management Framework", RFC 3410, December 2002.
[RFC3811] Nadeau, T., Ed., and J. Cucchiara, Ed., "Definitions of
Textual Conventions (TCs) for Multiprotocol Label
Switching (MPLS) Management", RFC 3811, June 2004.
[RFC3812] Srinivasan, C., Viswanathan, A., and T. Nadeau,
Venkatesan, et al. Expires May 08, 2014 [Page 57]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
"Multiprotocol Label Switching (MPLS) Traffic Engineering
(TE) Management Information Base (MIB)", RFC 3812, June
2004.
[RFC3813] Srinivasan, C., Viswanathan, A., and T. Nadeau,
"Multiprotocol Label Switching (MPLS) Label Switching
(LSR) Router Management Information Base (MIB)", RFC 3813,
June 2004.
[RFC4221] Nadeau, T., Srinivasan, C., and A. Farrel, "MSMGMT Label
Switching (MPLS) Management Overview", RFC 4221, November
2005.
[RFC4802] Nadeau, T., Ed., and A. Farrel, Ed., "Generalized
Multiprotocol Label Switching (GMPLS) Traffic Engineering
Management Information Base", RFC 4802, February 2007.
[RFC5226] Narten, T. and H. Alvestrand., "Guidelines for Writing an
IANA Considerations Section in RFCs", BCP 26, RFC 5226,
May 2008.
[RFC5654] Niven-Jenkins, B., Ed., Brungard, D., Ed., Betts, M.,
Ed.,Sprecher, N., and S. Ueno, "Requirements of an MPLS
Transport Profile", RFC 5654, September 2009.
[RFC6370] Bocci, M., Swallow, G., and E. Gray, "MPLS Transport
Profile (MPLS-TP) Identifiers", RFC 6370, September 2011.
[RFC6639] Venkatesan, M., King, D., "Multiprotocol Label Switching
Transport Profile (MPLS-TP) MIB-Based Management
Overview", RFC 6639, June 2012
[RFC6923] Winter, R., Gray, E., Helvoort, H., and M. Betts, "MPLS-TP
Identifiers Following ITU-T Conventions", RFC 6923, May
2013
17. Acknowledgments
The authors would like to thank Francesco Fondelli, Josh Littlefield,
Agrahara Kiran Koushik, Metrri Jain, Muly Ilan and Randy Presuhn for
their valuable comments. A special thanks to Joan Cucchiara for
really getting the MIB modules into shape.
18. Authors' Addresses
Venkatesan Mahalingam
Dell Inc.
350 Holger way, San Jose, CA, USA
Venkatesan, et al. Expires May 08, 2014 [Page 58]
INTERNET DRAFT MPLS-TP MIB November 04, 2013
Email: venkat.mahalingams@gmail.com
Sam Aldrin
Huawei Technologies
2330 Central Express Way,
Santa Clara, CA 95051, USA
Email: aldrin.ietf@gmail.com
Thomas D. Nadeau
Juniper Networks
10 Technology Park Drive, Westford, MA 01886
Email: tnadeau@juniper.net
Kannan KV Sampath
Redeem
India
Email: kannankvs@gmail.com
Venkatesan, et al. Expires May 08, 2014 [Page 59]