NTP Working Group                                             T. Mizrahi
Internet-Draft                          Huawei Network.IO Innovation Lab
Intended status: Informational                                 J. Fabini
Expires: August 15, 2019                                         TU Wien
                                                               A. Morton
                                                               AT&T Labs
                                                       February 11, 2019


               Guidelines for Defining Packet Timestamps
                  draft-ietf-ntp-packet-timestamps-06

Abstract

   Various network protocols make use of binary-encoded timestamps that
   are incorporated in the protocol packet format, referred to as packet
   timestamps for short.  This document specifies guidelines for
   defining packet timestamp formats in networking protocols at various
   layers.  It also presents three recommended timestamp formats.  The
   target audience of this memo includes network protocol designers.  It
   is expected that a new network protocol that requires a packet
   timestamp will, in most cases, use one of the recommended timestamp
   formats.  If none of the recommended formats fits the protocol
   requirements, the new protocol specification should specify the
   format of the packet timestamp according to the guidelines in this
   document.

   The rationale behind defining a relatively small set of recommended
   formats is that it enables significant reuse; network protocols can
   typically reuse the timestamp format of the Network Time Protocol
   (NTP) or the Precision Time Protocol (PTP), allowing a
   straightforward integration with an NTP or a PTP-based timer.
   Moreover, since accurate timestamping mechanisms are often
   implemented in hardware, a new network protocol that reuses an
   existing timestamp format can be quickly deployed using existing
   hardware timestamping capabilities.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at https://datatracker.ietf.org/drafts/current/.





Mizrahi, et al.          Expires August 15, 2019                [Page 1]


Internet-Draft              Packet Timestamps              February 2019


   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on August 15, 2019.

Copyright Notice

   Copyright (c) 2019 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (https://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   3
   2.  Terminology . . . . . . . . . . . . . . . . . . . . . . . . .   3
     2.1.  Requirements Language . . . . . . . . . . . . . . . . . .   3
     2.2.  Abbreviations . . . . . . . . . . . . . . . . . . . . . .   3
     2.3.  Terms used in this Document . . . . . . . . . . . . . . .   4
   3.  Packet Timestamp Specification Template . . . . . . . . . . .   4
   4.  Recommended Timestamp Formats . . . . . . . . . . . . . . . .   5
     4.1.  Using a Recommended Timestamp Format  . . . . . . . . . .   6
     4.2.  NTP Timestamp Formats . . . . . . . . . . . . . . . . . .   6
       4.2.1.  NTP 64-bit Timestamp Format . . . . . . . . . . . . .   6
       4.2.2.  NTP 32-bit Timestamp Format . . . . . . . . . . . . .   8
     4.3.  The PTP Truncated Timestamp Format  . . . . . . . . . . .   9
   5.  Synchronization Aspects . . . . . . . . . . . . . . . . . . .  11
   6.  Timestamp Use Cases . . . . . . . . . . . . . . . . . . . . .  12
     6.1.  Example 1 . . . . . . . . . . . . . . . . . . . . . . . .  13
     6.2.  Example 2 . . . . . . . . . . . . . . . . . . . . . . . .  13
   7.  Packet Timestamp Control Field  . . . . . . . . . . . . . . .  13
     7.1.  High-level Control Field Requirements . . . . . . . . . .  14
   8.  IANA Considerations . . . . . . . . . . . . . . . . . . . . .  15
   9.  Security Considerations . . . . . . . . . . . . . . . . . . .  15
   10. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . .  16
   11. References  . . . . . . . . . . . . . . . . . . . . . . . . .  16
     11.1.  Normative References . . . . . . . . . . . . . . . . . .  16
     11.2.  Informative References . . . . . . . . . . . . . . . . .  16



Mizrahi, et al.          Expires August 15, 2019                [Page 2]


Internet-Draft              Packet Timestamps              February 2019


   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  18

1.  Introduction

   Timestamps are widely used in network protocols for various purposes,
   including delay measurement, clock synchronization, and logging or
   reporting the time of an event.

   Timestamps are represented in the RFC series in one of two forms:
   text-based timestamps, and packet timestamps.  Text-based timestamps
   [RFC3339] are represented as user-friendly strings, and are widely
   used in the RFC series, for example in information objects and data
   models, e.g., [RFC5646], [RFC6991], and [RFC7493].  Packet
   timestamps, on the other hand, are represented by a compact binary
   field that has a fixed size, and are not intended to have a human-
   friendly format.  Packet timestamps are also very common in the RFC
   series, and are used for example for measuring delay and for
   synchronizing clocks, e.g., [RFC5905], [RFC4656], and [RFC1323].

   This memo presents guidelines for defining a packet timestamp format
   in network protocols.  Three recommended timestamp formats are
   presented.  It is expected that a new network protocol that requires
   a packet timestamp will, in most cases, use one of these recommended
   timestamp formats.  In some cases a network protocol may use more
   than one of the recommended timestamp formats.  However, if none of
   the recommended formats fits the protocol requirements, the new
   protocol specification should specify the format of the packet
   timestamp according to the guidelines in this document.

2.  Terminology

2.1.  Requirements Language

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in RFC 2119 [RFC2119].

2.2.  Abbreviations

   NTP         Network Time Protocol [RFC5905]

   PTP         Precision Time Protocol [IEEE1588]

   TAI         International Atomic Time

   UTC         Coordinated Universal Time





Mizrahi, et al.          Expires August 15, 2019                [Page 3]


Internet-Draft              Packet Timestamps              February 2019


2.3.  Terms used in this Document

   Timestamp error:       The difference between the timestamp value at
                          the device under test and the value of a
                          reference clock at the same time instant.

   Timestamp format:      The specification of a timestamp, which is
                          represented by a set of attributes that
                          unambiguously define the syntax and semantics
                          of a timestamp.

   Timestamp accuracy:    The mean over an ensemble of measurements of
                          the timestamp error.

   Timestamp precision:   The variation over an ensemble of measurements
                          of the timestamp error.

   Timestamp resolution:  The minimal time unit used for representing
                          the timestamp.

3.  Packet Timestamp Specification Template

   This memo recommends to use the timestamp formats defined in
   Section 4.  In cases where these timestamp formats do not satisfy the
   protocol requirements, the timestamp specification should clearly
   state the reasons for defining a new format.  Moreover, it is
   recommended to derive the new timestamp format from an existing
   timestamp format, either a timestamp format from this memo, or any
   other previously defined timestamp format.

   The timestamp specification must unambiguously define the syntax and
   the semantics of the timestamp.  The current section defines the
   minimum set of attributes, but it should be noted that in some cases
   additional attributes or aspects will need to be defined in the
   timestamp specification.

   This section defines a template for specifying packet timestamps.  A
   timestamp format specification MUST include at least the following
   aspects:

   Timestamp syntax:

      The structure of the timestamp field consists of:

      + Size: The number of bits (or octets) used to represent the
      packet timestamp field.  If the timestamp is comprised of more
      than one field, the size of each field is specified.




Mizrahi, et al.          Expires August 15, 2019                [Page 4]


Internet-Draft              Packet Timestamps              February 2019


   Timestamp semantics:

      + Units: The units used to represent the timestamp.  If the
      timestamp is comprised of more than one field, the units of each
      field are specified.

      + Resolution: The timestamp resolution; the resolution is equal to
      the timestamp field unit.  If the timestamp consists of two or
      more fields using different time units, then the resolution is the
      smallest time unit.

      + Wraparound: The wraparound period of the timestamp; any further
      wraparound-related considerations should be described here.

      + Epoch: The origin of the timescale used for the timestamp; the
      moment in time used as a reference for the timestamp value.  For
      example, the epoch may be based on a standard time scale, such as
      UTC.  Another example is a relative timestamp, in which the epoch
      is the time at which the device using the timestamp was powered
      up, and is not affected by leap seconds (see the next attribute).

      + Leap seconds: This subsection specifies whether the timestamp is
      affected by leap seconds.  If the timestamp is affected by leap
      seconds, then it represents the time elapsed since the epoch minus
      the number of leap seconds that have occurred since the epoch.

   Synchronization aspects:

      The specification of a network protocol that makes use of a packet
      timestamp is expected to include the synchronization aspects of
      using the timestamp.  While the synchronization aspects are not
      strictly part of the timestamp format specification, these aspects
      provide the necessary context for using the timestamp within the
      scope of the protocol.  Further details about synchronization
      aspects are discussed in Section 5.

4.  Recommended Timestamp Formats

   This memo defines a set of recommended timestamp formats.  Defining a
   relatively small set of recommended formats enables significant
   reuse; for example, a network protocol may reuse the NTP or PTP
   timestamp format, allowing a straightforward integration with an NTP
   or a PTP-based timer.  Moreover, since accurate timestamping
   mechanisms are often implemented in hardware, a new network protocol
   that reuses an existing timestamp format can be quickly deployed
   using existing hardware timestamping capabilities.  This memo
   recommends to use one of the timestamp formats specified below.




Mizrahi, et al.          Expires August 15, 2019                [Page 5]


Internet-Draft              Packet Timestamps              February 2019


   Clearly, different network protocols may have different requirements
   and constraints, and consequently may use different timestamp
   formats.  The choice of the specific timestamp format for a given
   protocol may depend on a various factors.  A few examples of factors
   that may affect the choice of the timestamp format:

   o  Timestamp size: while some network protocols use a large timestamp
      field, in some cases there may be constraints with respect to the
      timestamp size, affecting the choice of the timestamp format.

   o  Resolution: the time resolution is another factor that may
      directly affect the selected timestamp format.  A potentially
      important factor in this context is extensibility; it may be
      desirable to allow a timestamp format to be extensible to a higher
      resolution by extending the field.  For example, the resolution of
      the NTP 32-bit timestamp format can be improved by extending it to
      the NTP 64-bit timestamp format in a straightforward way.

   o  Wraparound period: the length of the time interval in which the
      timestamp is unique may also be an important factor in choosing
      the timestamp format.  Along with the timestamp resolution, these
      two factors determine the required number of bits in the
      timestamp.

   o  Common format for multiple protocols: if there are two or more
      network protocols that use timestamps and are often used together
      in typical systems, using a common timestamp format should be
      preferred if possible.  Specifically, if the network protocol that
      is being defined typically runs on a PC, then an NTP-based
      timestamp format may allow easier integration with an NTP-
      synchronized timer.  In contrast, a protocol that is typically
      deployed on a hardware-based platform, may make better use of a
      PTP-based timestamp, allowing more efficient integration with a
      PTP-synchronized timer.

4.1.  Using a Recommended Timestamp Format

   A specification that uses one of the recommended timestamp formats
   should specify explicitly that this is a recommended timestamp
   format, and point to the relevant section in the current memo.

4.2.  NTP Timestamp Formats

4.2.1.  NTP 64-bit Timestamp Format

   The Network Time Protocol (NTP) 64-bit timestamp format is defined in
   [RFC5905].  This timestamp format is used in several network
   protocols, including [RFC6374], [RFC4656], and [RFC5357].  Since this



Mizrahi, et al.          Expires August 15, 2019                [Page 6]


Internet-Draft              Packet Timestamps              February 2019


   timestamp format is used in NTP, this timestamp format should be
   preferred in network protocols that are typically deployed in concert
   with NTP.

   The format is presented in this section according to the template
   defined in Section 3.


        0                   1                   2                   3
        0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |                            Seconds                            |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |                            Fraction                           |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

              Figure 1: NTP [RFC5905] 64-bit Timestamp Format

   Timestamp field format:

      Seconds: specifies the integer portion of the number of seconds
      since the epoch.

      + Size: 32 bits.

      + Units: seconds.

      Fraction: specifies the fractional portion of the number of
      seconds since the epoch.

      + Size: 32 bits.

      + Units: the unit is 2^(-32) seconds, which is roughly equal to
      233 picoseconds.

   Epoch:

      The epoch is 1 January 1900 at 00:00 UTC.

      Note: As pointed out in [RFC5905], strictly speaking, UTC did not
      exist prior to 1 January 1972, but it is convenient to assume it
      has existed for all eternity.  The current epoch implies that the
      timestamp specifies the number of seconds since 1 January 1972 at
      00:00 UTC plus 2272060800 (which is the number of seconds between
      1 January 1900 and 1 January 1972).

   Leap seconds:




Mizrahi, et al.          Expires August 15, 2019                [Page 7]


Internet-Draft              Packet Timestamps              February 2019


      This timestamp format is affected by leap seconds.  The timestamp
      represents the number of seconds elapsed since the epoch minus the
      number of leap seconds.  Thus, during and possibly after the
      occurrence of a leap second, the value of the timestamp may
      temporarily be ambiguous, as further discussed in Section 5.

   Resolution:

      The resolution is 2^(-32) seconds.

   Wraparound:

      This time format wraps around every 2^32 seconds, which is roughly
      136 years.  The next wraparound will occur in the year 2036.

4.2.2.  NTP 32-bit Timestamp Format

   The Network Time Protocol (NTP) 32-bit timestamp format is defined in
   [RFC5905].  This timestamp format is used in
   [I-D.ietf-ippm-initial-registry] and
   [I-D.ietf-sfc-nsh-dc-allocation].  This timestamp format should be
   preferred in network protocols that are typically deployed in concert
   with NTP.  The 32-bit format can be used either when space
   constraints do not allow the use of the 64-bit format, or when the
   32-bit format satisfies the resolution and wraparound requirements.

   The format is presented in this section according to the template
   defined in Section 3.


        0                   1                   2                   3
        0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |          Seconds              |           Fraction            |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

              Figure 2: NTP [RFC5905] 32-bit Timestamp Format

   Timestamp field format:

      Seconds: specifies the integer portion of the number of seconds
      since the epoch.

      + Size: 16 bits.

      + Units: seconds.





Mizrahi, et al.          Expires August 15, 2019                [Page 8]


Internet-Draft              Packet Timestamps              February 2019


      Fraction: specifies the fractional portion of the number of
      seconds since the epoch.

      + Size: 16 bits.

      + Units: the unit is 2^(-16) seconds, which is roughly equal to
      15.3 microseconds.

   Epoch:

      The epoch is 1 January 1900 at 00:00 UTC.

      Note: As pointed out in [RFC5905], strictly speaking, UTC did not
      exist prior to 1 January 1972, but it is convenient to assume it
      has existed for all eternity.  The current epoch implies that the
      timestamp specifies the number of seconds since 1 January 1972 at
      00:00 UTC plus 2272060800 (which is the number of seconds between
      1 January 1900 and 1 January 1972).

   Leap seconds:

      This timestamp format is affected by leap seconds.  The timestamp
      represents the number of seconds elapsed since the epoch minus the
      number of leap seconds.  Thus, during and possibly after the
      occurrence of a leap second, the value of the timestamp may
      temporarily be ambiguous, as further discussed in Section 5.

   Resolution:

      The resolution is 2^(-16) seconds.

   Wraparound:

      This time format wraps around every 2^16 seconds, which is roughly
      18 hours.

4.3.  The PTP Truncated Timestamp Format

   The Precision Time Protocol (PTP) [IEEE1588] uses an 80-bit timestamp
   format.  The truncated timestamp format is a 64-bit field, which is
   the 64 least significant bits of the 80-bit PTP timestamp.  Since
   this timestamp format is similar to the one used in PTP, this
   timestamp format should be preferred in network protocols that are
   typically deployed in PTP-capable devices.

   The PTP truncated timestamp format was defined in [IEEE1588v1] and is
   used in several protocols, such as [RFC6374], [RFC7456], [RFC8186]
   and [ITU-T-Y.1731].



Mizrahi, et al.          Expires August 15, 2019                [Page 9]


Internet-Draft              Packet Timestamps              February 2019


        0                   1                   2                   3
        0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |                            Seconds                            |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |                          Nanoseconds                          |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

            Figure 3: PTP [IEEE1588] Truncated Timestamp Format

   Timestamp field format:

      Seconds: specifies the integer portion of the number of seconds
      since the epoch.

      + Size: 32 bits.

      + Units: seconds.

      Nanoseconds: specifies the fractional portion of the number of
      seconds since the epoch.

      + Size: 32 bits.

      + Units: nanoseconds.  The value of this field is in the range 0
      to (10^9)-1.

   Epoch:

      The PTP [IEEE1588] epoch is 1 January 1970 00:00:00 TAI.

   Leap seconds:

      This timestamp format is not affected by leap seconds.

   Resolution:

      The resolution is 1 nanosecond.

   Wraparound:

      This time format wraps around every 2^32 seconds, which is roughly
      136 years.  The next wraparound will occur in the year 2106.








Mizrahi, et al.          Expires August 15, 2019               [Page 10]


Internet-Draft              Packet Timestamps              February 2019


5.  Synchronization Aspects

   A specification that defines a new timestamp format or uses one of
   the recommended timestamp formats should include a section on
   Synchronization Aspects.  Note that the recommended timestamp formats
   defined in this document (Section 4) do not include the
   synchronization aspects of these timestamp formats, but it is
   expected that specifications of network protocols that make use of
   these formats should include the synchronization aspects.  Examples
   of a Synchronization Aspects section can be found in Section 6.

   The Synchronization Aspects section should specify all the
   assumptions and requirements related to synchronization.  For
   example, the synchronization aspects may specify whether nodes
   populating the timestamps should be synchronized among themselves,
   and whether the timestamp is measured with respect to a central
   reference clock such as an NTP server.  If time is assumed to be
   synchronized to a time standard such as UTC or TAI, it should be
   specified in this section.  Further considerations may be discussed
   in this section, such as the required timestamp accuracy and
   precision.

   Another aspect that should be discussed in this section is leap
   second [RFC5905] considerations.  The timestamp specification
   template (Section 3) specifies whether the timestamp is affected by
   leap seconds.  It is often the case that further details about leap
   seconds will need to be defined in the Synchronization Aspects
   section.  Generally speaking, a leap second is a one-second
   adjustment that is occasionally applied to UTC in order to keep it
   aligned to the solar time.  A leap second may be either positive or
   negative, i.e., the clock may either be shifted one second forwards
   or backwards.  All leap seconds that have occurred up to the
   publication of this document have been in the backwards direction,
   and although forward leap seconds are theoretically possible, the
   text throughout this document focuses on the common case, which is
   the backward leap second.  In a timekeeping system that considers
   leap seconds, the system clock may be affected by a leap second in
   one of three possible ways:

   o  The clock is turned backwards one second at the end of the leap
      second.

   o  The clock is frozen during the duration of the leap second.

   o  The clock is slowed down during the leap second and adjacent time
      intervals until the new time value catches up.  The interval for
      this process, commonly referred to as leap smear, can range from




Mizrahi, et al.          Expires August 15, 2019               [Page 11]


Internet-Draft              Packet Timestamps              February 2019


      several seconds to several hours before, during, and/or after the
      occurrence of the leap second.

   The way leap seconds are handled depends on the synchronization
   protocol, and is thus not specified in this document.  However, if a
   timestamp format is defined with respect to a timescale that is
   affected by leap seconds, the Synchronization Aspects section should
   specify how the use of leap seconds affects the timestamp usage.

6.  Timestamp Use Cases

   Packet timestamps are used in various network protocols.  Typical
   applications of packet timestamps include delay measurement, clock
   synchronization, and others.  The following table presents a (non-
   exhaustive) list of protocols that use packet timestamps, and the
   timestamp formats used in each of these protocols.


   +------------------+-----------------------------------+-----------+
   |                  |       Recommended formats         |  Other    |
   +------------------+-----------+-----------+-----------+  format   |
   | Protocol         |NTP 64-bit |NTP 32-bit |PTP Trunc. |           |
   +------------------+-----------+-----------+-----------+-----------+
   | NTP   [RFC5905]  |     +     |           |           |           |
   +------------------+-----------+-----------+-----------+-----------+
   | OWAMP [RFC4656]  |     +     |           |           |           |
   +------------------+-----------+-----------+-----------+-----------+
   | TWAMP [RFC5357]  |     +     |           |           |           |
   | TWAMP [RFC8186]  |     +     |           |     +     |           |
   +------------------+-----------+-----------+-----------+-----------+
   | TRILL [RFC7456]  |           |           |     +     |           |
   +------------------+-----------+-----------+-----------+-----------+
   | MPLS  [RFC6374]  |           |           |     +     |           |
   +------------------+-----------+-----------+-----------+-----------+
   | TCP   [RFC1323]  |           |           |           |     +     |
   +------------------+-----------+-----------+-----------+-----------+
   | RTP   [RFC3550]  |     +     |           |           |     +     |
   +------------------+-----------+-----------+-----------+-----------+
   | IPFIX [RFC7011]  |           |           |           |     +     |
   +------------------+-----------+-----------+-----------+-----------+
   | [I-D.ietf-ippm-  |     +     |     +     |           |           |
   | initial-registry]|           |           |           |           |
   +------------------+-----------+-----------+-----------+-----------+
   | [I-D.ietf-sfc-nsh|           |     +     |     +     |           |
   |  -dc-allocation] |           |           |           |           |
   +------------------+-----------+-----------+-----------+-----------+

              Figure 4: Protocols that use Packet Timestamps



Mizrahi, et al.          Expires August 15, 2019               [Page 12]


Internet-Draft              Packet Timestamps              February 2019


   The rest of this section presents two hypothetic examples of network
   protocol specifications that use one of the recommended timestamp
   formats.  The examples include the text that specifies the
   information related to the timestamp format.

6.1.  Example 1

   Timestamp:

      The timestamp format used in this specification is the NTP
      [RFC5905] 64-bit format, as specified in Section 4.2.1 of
      [I-D.ietf-ntp-packet-timestamps].

   Synchronization aspects:

      It is assumed that nodes that run this protocol are synchronized
      to UTC using a synchronization mechanism that is outside the scope
      of this document.  In typical deployments this protocol will run
      on a machine that uses NTP [RFC5905] for synchronization.  Thus,
      the timestamp may be derived from the NTP-synchronized clock,
      allowing the timestamp to be measured with respect to the clock of
      an NTP server.  Since the NTP time format is affected by leap
      seconds, the current timestamp format is similarly affected.
      Thus, the value of a timestamp during or slightly after a leap
      second may be temporarily inaccurate.

6.2.  Example 2

   Timestamp:

      The timestamp format used in this specification is the PTP
      [IEEE1588] Truncated format, as specified in Section 4.3 of
      [I-D.ietf-ntp-packet-timestamps].

   Synchronization aspects:

      It is assumed that nodes that run this protocol are synchronized
      among themselves.  Nodes may be synchronized to a global reference
      time.  Note that if PTP [IEEE1588] is used for synchronization,
      the timestamp may be derived from the PTP-synchronized clock,
      allowing the timestamp to be measured with respect to the clock of
      an PTP Grandmaster clock.

7.  Packet Timestamp Control Field

   In some cases it is desirable to have a control field that describes
   structure, format, content, and properties of timestamps.  Control
   information about the timestamp format can be conveyed in some



Mizrahi, et al.          Expires August 15, 2019               [Page 13]


Internet-Draft              Packet Timestamps              February 2019


   protocols using a dedicated control plane protocol, or may be made
   available at the management plane, for example using a YANG data
   model.  An optional control field allows some of the control
   information to be attached to the timestamp.

   An example of a packet timestamp control field is the Error Estimate
   field, defined by Section 4.1.2 in [RFC4656], which is used in OWAMP
   [RFC4656] and TWAMP [RFC5357].

   This section defines high-level guidelines for defining packet
   timestamp control fields in network protocols that can benefit from
   such timestamp-related control information.  The word 'requirements'
   is used in its informal context in this section.

7.1.  High-level Control Field Requirements

   A control field for packet timestamps must offer an adequate feature
   set and fulfill a series of requirements to be usable and accepted.
   The following list captures the main high-level requirements for
   timestamp fields.

   1.  Extensible Feature Set: protocols and applications depend on
       various timestamp characteristics.  A timestamp control field
       must support a variable number of elements (components) that
       either describe or quantify timestamp-specific characteristics or
       parameters.  Examples of potential elements include timestamp
       size, encoding, accuracy, leap seconds, reference clock
       identifiers, etc.

   2.  Size: Essential for an efficient use of timestamp control fields
       is the trade-off between supported features and control field
       size.  Protocols and applications may select the specific control
       field elements that are needed for their operation from the set
       of available elements.

   3.  Composition: Applications may depend on specific control field
       elements being present in messages.  The status of these elements
       may be either mandatory, conditional mandatory, or optional,
       depending on the specific application and context.  A control
       field specification must support applications in conveying or
       negotiating (a) the set of control field elements along with (b)
       the status of any element (i.e., mandatory, conditional
       mandatory, or optional) by defining appropriate data structures
       and identity codes.

   4.  Category: Control field elements can characterize either static
       timestamp information (like, e.g., timestamp size in bytes and
       timestamp semantics: NTP 64 bit format) or runtime timestamp



Mizrahi, et al.          Expires August 15, 2019               [Page 14]


Internet-Draft              Packet Timestamps              February 2019


       information (like, e.g., estimated timestamp accuracy at the time
       of sampling: 20 microseconds to UTC).  For efficiency reason it
       may be meaningful to support separation of these two concepts:
       while the former (static) information is typically valid
       throughout a protocol session and may be conveyed only once, at
       session establishment time, the latter (runtime) information
       augments any timestamp instance and may cause substantial
       overhead for high-traffic protocols.

   Proposals for timestamp control fields will be defined in separate
   documents and are out of scope of this memo.

8.  IANA Considerations

   This memo includes no request to IANA.

9.  Security Considerations

   A network protocol that uses a packet timestamp MUST specify the
   security considerations that result from using the timestamp.  This
   section provides an overview of some of the common security
   considerations of using timestamps.

   Any metadata that is attached to control or data packets, and
   specifically packet timestamps, can facilitate network
   reconnaissance; by passively eavesdropping to timestamped packets an
   attacker can gather information about the network performance, and
   about the level of synchronization between nodes.

   Timestamps can be spoofed or modified by on-path attackers, thus
   attacking the application that uses the timestamps.  For example, if
   timestamps are used in a delay measurement protocol, an attacker can
   modify en route timestamps in a way that manipulates the measurement
   results.  Integrity protection mechanisms, such as Hashed Message
   Authentication Codes (HMAC), can mitigate such attacks.  The
   specification of an integrity protection mechanism is outside the
   scope of this document, as typically integrity protection will be
   defined on a per-network-protocol basis, and not specifically for the
   timestamp field.

   Another potential threat that can have a similar impact is delay
   attacks.  An attacker can maliciously delay some or all of the en
   route messages, with the same harmful implications as described in
   the previous paragraph.  Mitigating delay attacks is a significant
   challenge; in contrast to spoofing and modification attacks, the
   delay attack cannot be prevented by cryptographic integrity
   protection mechanisms.  In some cases delay attacks can be mitigated
   by sending the timestamped information through multiple paths,



Mizrahi, et al.          Expires August 15, 2019               [Page 15]


Internet-Draft              Packet Timestamps              February 2019


   allowing to detect and to be resilient to an attacker that has access
   to one of the paths.

   In many cases timestamping relies on an underlying synchronization
   mechanism.  Thus, any attack that compromises the synchronization
   mechanism can also compromise protocols that use timestamping.
   Attacks on time protocols are discussed in detail in [RFC7384].

10.  Acknowledgments

   The authors thank Yaakov Stein, Greg Mirsky, Warner Losh, Rodney
   Cummings, Miroslav Lichvar, Denis Reilly, Daniel Franke, Watson Ladd,
   and other members of the NTP working group for many helpful comments.
   The authors gratefully acknowledge Harlan Stenn and the people from
   the Network Time Foundation for sharing their thoughts and ideas.

11.  References

11.1.  Normative References

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/RFC2119, March 1997,
              <https://www.rfc-editor.org/info/rfc2119>.

11.2.  Informative References

   [I-D.ietf-ippm-initial-registry]
              Morton, A., Bagnulo, M., Eardley, P., and K. D'Souza,
              "Initial Performance Metric Registry Entries", draft-ietf-
              ippm-initial-registry-09 (work in progress), December
              2018.

   [I-D.ietf-ntp-packet-timestamps]
              Mizrahi, T., Fabini, J., and A. Morton, "Guidelines for
              Defining Packet Timestamps", draft-ietf-ntp-packet-
              timestamps-05 (work in progress), December 2018.

   [I-D.ietf-sfc-nsh-dc-allocation]
              Guichard, J., Smith, M., Kumar, S., Majee, S., and T.
              Mizrahi, "Network Service Header (NSH) MD Type 1: Context
              Header Allocation (Data Center)", draft-ietf-sfc-nsh-dc-
              allocation-02 (work in progress), September 2018.

   [IEEE1588]
              IEEE, "IEEE 1588 Standard for a Precision Clock
              Synchronization Protocol for Networked Measurement and
              Control Systems Version 2", 2008.



Mizrahi, et al.          Expires August 15, 2019               [Page 16]


Internet-Draft              Packet Timestamps              February 2019


   [IEEE1588v1]
              IEEE, "IEEE 1588 Standard for a Precision Clock
              Synchronization Protocol for Networked Measurement and
              Control Systems", 2002.

   [ITU-T-Y.1731]
              ITU-T, "OAM functions and mechanisms for Ethernet based
              Networks", 2013.

   [RFC1323]  Jacobson, V., Braden, R., and D. Borman, "TCP Extensions
              for High Performance", RFC 1323, DOI 10.17487/RFC1323, May
              1992, <https://www.rfc-editor.org/info/rfc1323>.

   [RFC3339]  Klyne, G. and C. Newman, "Date and Time on the Internet:
              Timestamps", RFC 3339, DOI 10.17487/RFC3339, July 2002,
              <https://www.rfc-editor.org/info/rfc3339>.

   [RFC3550]  Schulzrinne, H., Casner, S., Frederick, R., and V.
              Jacobson, "RTP: A Transport Protocol for Real-Time
              Applications", STD 64, RFC 3550, DOI 10.17487/RFC3550,
              July 2003, <https://www.rfc-editor.org/info/rfc3550>.

   [RFC4656]  Shalunov, S., Teitelbaum, B., Karp, A., Boote, J., and M.
              Zekauskas, "A One-way Active Measurement Protocol
              (OWAMP)", RFC 4656, DOI 10.17487/RFC4656, September 2006,
              <https://www.rfc-editor.org/info/rfc4656>.

   [RFC5357]  Hedayat, K., Krzanowski, R., Morton, A., Yum, K., and J.
              Babiarz, "A Two-Way Active Measurement Protocol (TWAMP)",
              RFC 5357, DOI 10.17487/RFC5357, October 2008,
              <https://www.rfc-editor.org/info/rfc5357>.

   [RFC5646]  Phillips, A., Ed. and M. Davis, Ed., "Tags for Identifying
              Languages", BCP 47, RFC 5646, DOI 10.17487/RFC5646,
              September 2009, <https://www.rfc-editor.org/info/rfc5646>.

   [RFC5905]  Mills, D., Martin, J., Ed., Burbank, J., and W. Kasch,
              "Network Time Protocol Version 4: Protocol and Algorithms
              Specification", RFC 5905, DOI 10.17487/RFC5905, June 2010,
              <https://www.rfc-editor.org/info/rfc5905>.

   [RFC6374]  Frost, D. and S. Bryant, "Packet Loss and Delay
              Measurement for MPLS Networks", RFC 6374,
              DOI 10.17487/RFC6374, September 2011,
              <https://www.rfc-editor.org/info/rfc6374>.






Mizrahi, et al.          Expires August 15, 2019               [Page 17]


Internet-Draft              Packet Timestamps              February 2019


   [RFC6991]  Schoenwaelder, J., Ed., "Common YANG Data Types",
              RFC 6991, DOI 10.17487/RFC6991, July 2013,
              <https://www.rfc-editor.org/info/rfc6991>.

   [RFC7011]  Claise, B., Ed., Trammell, B., Ed., and P. Aitken,
              "Specification of the IP Flow Information Export (IPFIX)
              Protocol for the Exchange of Flow Information", STD 77,
              RFC 7011, DOI 10.17487/RFC7011, September 2013,
              <https://www.rfc-editor.org/info/rfc7011>.

   [RFC7384]  Mizrahi, T., "Security Requirements of Time Protocols in
              Packet Switched Networks", RFC 7384, DOI 10.17487/RFC7384,
              October 2014, <https://www.rfc-editor.org/info/rfc7384>.

   [RFC7456]  Mizrahi, T., Senevirathne, T., Salam, S., Kumar, D., and
              D. Eastlake 3rd, "Loss and Delay Measurement in
              Transparent Interconnection of Lots of Links (TRILL)",
              RFC 7456, DOI 10.17487/RFC7456, March 2015,
              <https://www.rfc-editor.org/info/rfc7456>.

   [RFC7493]  Bray, T., Ed., "The I-JSON Message Format", RFC 7493,
              DOI 10.17487/RFC7493, March 2015,
              <https://www.rfc-editor.org/info/rfc7493>.

   [RFC8186]  Mirsky, G. and I. Meilik, "Support of the IEEE 1588
              Timestamp Format in a Two-Way Active Measurement Protocol
              (TWAMP)", RFC 8186, DOI 10.17487/RFC8186, June 2017,
              <https://www.rfc-editor.org/info/rfc8186>.

Authors' Addresses

   Tal Mizrahi
   Huawei Network.IO Innovation Lab
   Israel

   Email: tal.mizrahi.phd@gmail.com


   Joachim Fabini
   TU Wien
   Gusshausstrasse 25/E389
   Vienna 1040
   Austria

   Phone: +43 1 58801 38813
   Fax:   +43 1 58801 38898
   Email: Joachim.Fabini@tuwien.ac.at
   URI:   http://www.tc.tuwien.ac.at/about-us/staff/joachim-fabini/



Mizrahi, et al.          Expires August 15, 2019               [Page 18]


Internet-Draft              Packet Timestamps              February 2019


   Al Morton
   AT&T Labs
   200 Laurel Avenue South
   Middletown,, NJ  07748
   USA

   Phone: +1 732 420 1571
   Fax:   +1 732 368 1192
   Email: acmorton@att.com
   URI:   http://home.comcast.net/~acmacm/









































Mizrahi, et al.          Expires August 15, 2019               [Page 19]