Softwire WG M. Boucadair
Internet-Draft France Telecom
Intended status: Standards Track I. Farrer
Expires: December 01, 2013 Deutsche Telekom
S. Perreault, Ed.
Viagenie
S. Sivakumar, Ed.
Cisco Systems
May 30, 2013
Unified IPv4-in-IPv6 Softwire CPE
draft-ietf-softwire-unified-cpe-01
Abstract
Transporting IPv4 packets encapsulated in IPv6 is a common solution
to the problem of IPv4 service continuity over IPv6-only provider
networks. A number of differing functional approaches have been
developed for this, each having their own specific characteristics.
As these approaches share a similar functional architecture and use
the same data plane mechanisms, this memo describes a specification
whereby a single CPE can interwork with all of the standardized and
proposed approaches to providing encapsulated IPv4 in IPv6 services.
Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on December 01, 2013.
Boucadair, et al. Expires December 01, 2013 [Page 1]
Internet-Draft Generic v4 in v6 CPE Provisioning Profile May 2013
Copyright Notice
Copyright (c) 2013 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
1.1. Rationale . . . . . . . . . . . . . . . . . . . . . . . . 3
2. IPv4 Service Continuity Architectures: A 'Big Picture'
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.1. Functional Elements . . . . . . . . . . . . . . . . . . . 5
2.2. Required Provisioning Information . . . . . . . . . . . . 7
3. Unified Softwire CPE Behaviour . . . . . . . . . . . . . . . 7
3.1. IPv4 Address Functional Requirements . . . . . . . . . . 7
3.2. Generic CPE Bootstrapping Logic . . . . . . . . . . . . . 8
3.3. Customer Side DHCP Based Provisioning . . . . . . . . . . 9
3.4. Forwarding Action by the Customer End-Node . . . . . . . 12
4. Future Expansion of the Unified CPE Model . . . . . . . . . . 12
5. Security Considerations . . . . . . . . . . . . . . . . . . . 12
6. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 12
7. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 13
8. References . . . . . . . . . . . . . . . . . . . . . . . . . 13
8.1. Normative References . . . . . . . . . . . . . . . . . . 13
8.2. Informative References . . . . . . . . . . . . . . . . . 13
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 14
1. Introduction
IPv4 service continuity is one of the major technical challenges
which must be considered during IPv6 migration. Over the past few
years, a number of different approaches have been developed to assist
with this problem. These approaches, or modes, exist in order to
meet the particular deployment, scaling, addressing and other
requirements of different service provider's networks. Section 2 of
this document describes these approaches in more detail.
Boucadair, et al. Expires December 01, 2013 [Page 2]
Internet-Draft Generic v4 in v6 CPE Provisioning Profile May 2013
A common feature shared between all of the differing modes is the
integration of softwire tunnel end-point functionality into the CPE
router. Due to this inherent data plane similarity, a single CPE may
be capable of supporting several different approaches. Users may
also wish to configure a specific mode of operation.
A service provider's network may also have more than one mode enabled
in order to support diverse CPE client functionality, during
migration between modes or where services require specific supporting
softwire architectures.
For softwire based services to be successfully established, it is
essential that the customer end-node, the service provider end-node
and provisioning systems are able to indicate their capabilities and
preferred mode of operation.
This memo describes the logic required by both the CPE tunnel end-
node and the service provider's provisioning infrastructure so that
softwire services can be provided in mixed-mode environments.
1.1. Rationale
The following rationale has been adopted for this document:
(1) Describe the functionality of each the different solution modes
and provide clear distinctions between them
(2) Simplify solution migration paths: Define unified CPE behavior,
allowing for smooth migration between the different modes
(3) Deterministic CPE co-existence behavior: Specify the behavior
when several modes co-exist in the CPE
(4) Deterministic service provider co-existence behavior: Specify
the behavior when several modes co-exist in the service providers
network
(5) Re-usability: Maximize the re-use of existing functional blocks
including tunnel end-points, port restricted NAPT44, forwarding
behavior, etc.
(6) Solution agnostic: Adopt neutral terminology and avoid (as far
as possible) overloading the document with solution-specific terms
(7) Flexibility: Allow operators to compile CPE software only for
the mode(s) necessary for their chosen deployment context(s)
Boucadair, et al. Expires December 01, 2013 [Page 3]
Internet-Draft Generic v4 in v6 CPE Provisioning Profile May 2013
(8) Simplicity: Provide a model that allows operators to only
implement the specific mode(s) that they require without the
additional complexity of unneeded modes.
2. IPv4 Service Continuity Architectures: A 'Big Picture' Overview
The solutions which have been proposed within the Softwire WG can be
categorized into three main functional approaches, differentiated by
the amount and type of state that the service provider needs to
maintain within their network:
(1) Full stateful approach (DS-Lite, [RFC6333]): Requires per-
session state to be maintained in the Service Provider's network.
(2) Binding approach (e.g., Lightweight 4over6 (Lw4o6)
[I-D.ietf-softwire-lw4over6][I-D.ietf-softwire-public-4over6] or
MAP 1:1 [I-D.ietf-softwire-map] ): Requires a single per-
subscriber state (or a few) to be maintained in the Service
Provider's network.
(3) Full stateless approach (MAP, [I-D.ietf-softwire-map]): Does not
require per-session or per-subscriber state to be maintained in
the Service Provider's network.
All these approaches share a similar architecture, with a tunnel
endpoint located in the CPE and a remote tunnel endpoint. All use
IPv6 as the transport protocol for the delivery of an IPv4
connectivity service using an IPv4-in-IPv6 encapsulation scheme
[RFC2473].
Several cases can be envisaged:
1. The CPE is complied to support only one mode: No issue is raised
by this case.
2. The CPE supports several modes but only one mode is explicitly
configured: No issue is raised by this case.
3. The CPE supports several modes but no mode is explicitly enabled:
the CPE will need additional triggers to decide which mode to
activate.
4. The CPE supports several modes and several modes are configured:
the CPE will need additional triggers to decide which mode to
activate.
As this document describes a provisioning profile whereby a single
CPE could be capable of supporting any, or multiple modes, the
customer should not be required to have any knowledge of the
capabilities and configuration of their CPE, or of their service
provider's network.
Boucadair, et al. Expires December 01, 2013 [Page 4]
Internet-Draft Generic v4 in v6 CPE Provisioning Profile May 2013
The service provider, however, may have only a single mode enabled,
or may have multiple modes, but with one preferred mode. For this
reason, it is necessary to approach the configuration of CPEs from
the standpoint of the service provider's network capabilities.
2.1. Functional Elements
The functional elements for each of the solution modes are listed in
Table 1:
+---------+---------------+--------------+
| Mode | Customer side | Network side |
+---------+---------------+--------------+
| DS-Lite | B4 | AFTR |
| Lw4o6 | lwB4 | lwAFTR |
| MAP | MAP CE | MAP BR |
+---------+---------------+--------------+
Table 1: Functional Elements
Table 2 describes each functional element:
Boucadair, et al. Expires December 01, 2013 [Page 5]
Internet-Draft Generic v4 in v6 CPE Provisioning Profile May 2013
+----------------+--------------------------------------------------+
| Functional | Description |
| Element | |
+----------------+--------------------------------------------------+
| B4 | An IPv4-in-IPv6 tunnel endpoint; the B4 creates |
| | a tunnel to a pre-configured remote tunnel |
| | endpoint. |
| AFTR | Provides both an IPv4-in-IPv6 tunnel endpoint |
| | and a NAT44 function implemented in the same |
| | node. |
| lwB4 | A B4 which supports port-restricted IPv4 |
| | addresses. An lwB4 MAY also provide a NAT44 |
| | function. |
| lwAFTR | An IPv4-in-IPv6 tunnel endpoint which maintains |
| | per-subscriber address binding. Unlike the AFTR, |
| | it MUST NOT perform a NAPT44 function. |
| MAP CE | A B4 which supports port-restricted IPv4 |
| | addresses. It MAY be co-located with a NAT44. A |
| | MAP CE forwards IPv4-in-IPv6 packets using |
| | provisioned mapping rules to derive the remote |
| | tunnel endpoint. |
| MAP BR | An IPv4-in-IPv6 tunnel endpoint. A MAP BR |
| | forwards IPv4-in-IPv6 packets following pre- |
| | configured mapping rules. |
+----------------+--------------------------------------------------+
Table 2: Required Element Functionality
Table 3 identifies features required by the customer end-node.
+--------------+----------------+-----------------+-----------------+
| Functional | IPv4-in-IPv6 | Port-restricted | Port-restricted |
| Element | tunnel | IPv4 | NAT44 |
| | endpoint | | |
+--------------+----------------+-----------------+-----------------+
| B4 | Yes | N/A | No |
| lwB4 | Yes | Yes | Optional |
| MAP-E CE | Yes | Yes | Optional |
+--------------+----------------+-----------------+-----------------+
Table 3: Supported Features
Boucadair, et al. Expires December 01, 2013 [Page 6]
Internet-Draft Generic v4 in v6 CPE Provisioning Profile May 2013
2.2. Required Provisioning Information
Table 4 identifies the provisioning information required for each
solution mode.
+---------+---------------------------------------------+
| Mode | Provisioning Information |
+---------+---------------------------------------------+
| DS-Lite | Remote IPv4-in-IPv6 Tunnel Endpoint Address |
| Lw4o6 | Remote IPv4-in-IPv6 Tunnel Endpoint Address |
| | IPv4 Address |
| | Port Set |
| MAP-E | Mapping Rules |
| | MAP Domain Parameters |
+---------+---------------------------------------------+
Table 4: Provisioning Information
Note: MAP Mapping Rules are translated into the following
configuration parameters: Set of remote IPv4-in-IPv6 tunnel endpoint
addresses, IPv4 address and port set.
Note: Required provisioning information for each mode may also
be represented as follows:
DS-Lite: - Remote IPv4-in-IPv6 Tunnel Endpoint
Lw4o6: - DS-Lite set of provisioning information
- IPv4 address
- Port set
MAP-E: - Lw4o6 set of provisioning information
- Forwarding mapping rules
3. Unified Softwire CPE Behaviour
This section specifies a unified CPE behavior capable of supporting
any one, or combination of, the three modes.
3.1. IPv4 Address Functional Requirements
The following two requirements must be met by the functional
elements:
Full IPv4 Address Assignment All the aforementioned modes MUST be
designed to allow either a full or a shared IPv4 address to be
assigned to a customer end-node. DS-Lite and MAP-E fulfil this
requirement. With minor changes, the [I-D.ietf-softwire-lw4over6]
specification can be updated to assign full IPv4 addresses.
Boucadair, et al. Expires December 01, 2013 [Page 7]
Internet-Draft Generic v4 in v6 CPE Provisioning Profile May 2013
Customer End-Node NAT A NAT function within the customer end-node is
not required for DS-Lite, while it is optional for both MAP-E and
Lw4o6. When NAT is enabled for MAP-E or Lw4o6, the customer end-
node NAT MUST be able to restrict the external translated source
ports to the set of ports that it has been provisioned with.
3.2. Generic CPE Bootstrapping Logic
The generic provisioning logic is designed to meet the following
requirements:
o When several service continuity modes are supported by the same
CPE, it MUST be possible to configure a single mode for use.
o For each network attachment, the end-node MUST NOT activate more
than one mode.
o The CPE MAY be configured by a user or via remote device
management means (e.g., DHCP, TR-069).
o A network which supports one or several modes MUST return valid
configuration data enabling requesting devices to unambiguously
select a single mode to use for attachment.
o A CPE which supports only one mode or it is configured to enable
only mode MUST ignore any configuration parameter which is not
required for the mode it supports.
This section sketches a generic algorithm to be followed by a CPE
supporting one or more of the modes listed above. Based on the
retrieved information, the CPE will determine which mode to activate.
(1) If a given mode is enabled (DS-Lite, Lw4o6 or MAP-E), the CPE
MUST be configured with the required provisioning information
listed in Table 4. If all of the required information is not
available locally, the CPE MUST use available provisioning means
(e.g., DHCP) to retrieve the missing configuration data.
(2) If the CPE supports several modes, but no mode is explicitly
enabled, the CPE MUST use available provisioning means (e.g.,
DHCP) to retrieve available configuration parameters and use the
availability of individual parameters to ascertain which
functional mode to configure:
(2.1) If only a Remote IPv4-in-IPv6 Tunnel Endpoint is received,
the CPE MUST proceed as follows:
(2.1)
Boucadair, et al. Expires December 01, 2013 [Page 8]
Internet-Draft Generic v4 in v6 CPE Provisioning Profile May 2013
(2.1.1) IPv4-in-IPv6 tunnel endpoint initialization is
defined in [RFC6333].
(2.1.2) Outbound IPv4 packets are forwarded to the next hop
as specified in Section 3.4.
(2.3) If a Remote IPv4-in-IPv6 Tunnel Endpoint, an IPv4 Address
and optionally a Port Set are received, the CPE MUST behave
as follows:
(2.3)
(2.2.1) IPv4-in-IPv6 tunnel endpoint initialization is
similar to the B4 [RFC6333].
(2.2.2) When NAPT44 is required (e.g., because the CPE is a
router), a NAPT44 module is enabled.
(2.2.3) The tunnel endpoint address is selected from the
native IPv6 addresses configured on the CPE. No
particular considerations are required to be taken
into account to generate the Interface Identifier.
(2.2.4) When a port set is provisioned, the external source
ports MUST be restricted to the provisioned set of
ports.
(2.2.5) After translation, outbound IPv4 packets are
forwarded to the next hop as specified in
Section 3.4.
(2.6) If Mapping Rule(s) are received, the CPE MUST behave as
follows:
(2.6)
(2.3.1) IPv4-in-IPv6 tunnel endpoint initialization is
similar to the B4 [RFC6333].
(2.3.2) The tunnel endpoint is assigned with an IPv6
address which includes an IPv4 address. The MAP
Interface Identifier is based on the format
specified in Section 2.2 of [RFC6052].
(2.3.3) When NAPT44 is required (e.g., because the CPE is a
router), a NAPT44 module is enabled.
(2.3.4) When a port set is provisioned, the external source
port MUST be restricted to the provisioned set of
ports.
(2.3.5) After translation, outbound IPv4 packets then
forwarded to the next hop as specified in
Section 3.4.
3.3. Customer Side DHCP Based Provisioning
Boucadair, et al. Expires December 01, 2013 [Page 9]
Internet-Draft Generic v4 in v6 CPE Provisioning Profile May 2013
[DISCUSSION NOTE:
1. This section will be updated to reflect the consensus from DHC
WG
2. As it is proposed that OPTION_MAP would be used for all new
softwire provisioning, should we rename OPTION_MAP to
OPTION_SW (incl. the associated sub-options)?]
This section describes how the logic is implemented using DHCPv6 to
provision the necessary parameters for Unified CPE configuration.
Other provisioning mechanisms (e.g. static, PCP etc.) may be used
instead of, or in addition to DHCPv6 to provision the CPE. DHCP-
based configuration SHOULD be implemented by the customer end-node.
The following two DHCPv6 options are used:
OPTION_AFTR_NAME [RFC6334] Provides the FQDN for the remote IPv4
-in-IPv6 tunnel end-point.
OPTION_MAP [I-D.ietf-softwire-map-dhcp] Provides
IPv4-related configuration for binding mode and/
or mapping rules for stateless mode (including
MAP parameters such as offset, domain prefix,
etc.).
By default, the customer end-node SHOULD support DHCPv6 MAP options
to provision IPv4-related connectivity parameters. If a dynamic port
assignment scheme is adopted, [I-D.ietf-dhc-dhcpv4-over-dhcpv6]
SHOULD be supported.
The following additional sub-options are used to convey the different
possible configurations options for Binding Mode (using static or
dynamic IPv4 addressing plus additional DHCPv6 options):
OPTION_MAP_BIND A sub-option used to convey an IPv4 address (for
example, encoded as an IPv4-mapped IPv6 address
[RFC4291]). This address is used when binding
mode is enabled. The receipt of OPTION_MAP_BIND
is an implicit indication to the customer side
device to operate in binding, rather than
stateless mode.
OPTION_MAP_BIND_DYN A sub-option used to indicate to the client that
it must use the dynamic DHCPv4 over DHCPv6
process described in
[I-D.ietf-dhc-dhcpv4-over-dhcpv6]
Boucadair, et al. Expires December 01, 2013 [Page 10]
Internet-Draft Generic v4 in v6 CPE Provisioning Profile May 2013
The customer end-node uses the DHCP Option Request Option (ORO) to
request either one or both of these options depending on which modes
it is capable of and configured to support.
The DHCP option(s) sent in the response allow the service provider to
inform the customer end-node which operating mode to enable.
The following table shows the different DHCP options (and sub-
options) that the service provider can supply in a response. The
CPE's interpretation of the different Binding Options parameters are
described below.
+---------------------------+------------+------------+-------------+
| DHCP Option | Stateful | Binding | Stateless |
| | Mode | Mode | Mode |
+---------------------------+------------+------------+-------------+
| OPTION_AFTR_NAME | Yes | Yes | Yes |
| Binding Option(s) | No | Yes | No |
| OPTION_MAP_RULE | No | No | Yes |
| OPTION_MAP_PORTPARAMS | No | Optional | Optional |
+---------------------------+------------+------------+-------------+
Table 5: DHCP Option Provisioning Matrix
The customer side device MUST interpret the received DHCP
configuration parameters according to the logic defined in
Section 3.2:
o If only OPTION_AFTR_NAME is received, then the device MUST operate
in stateful mode
o If both OPTION_AFTR_NAME and Binding Option(s) are received then
the device MUST operate in binding mode
o If one or more OPTION_MAP_RULE options are received, then the
customer side device MUST operate in stateless mode
o If both OPTION_AFTR_NAME and OPTION_MAP_RULE(s) are received, then
the customer side device MUST operate as a MAP CE.
OPTION_AFTR_NAME provides the FQDN of the MAP BR.
o If OPTION_MAP_PORTPARAMS is received as a sub-option to either
OPTION_MAP_BIND or OPTION_MAP_RULE, then NAPT44 MUST be configured
using the supplied port-set for external translated source ports.
From the service providers side, the following rule MUST be followed:
Boucadair, et al. Expires December 01, 2013 [Page 11]
Internet-Draft Generic v4 in v6 CPE Provisioning Profile May 2013
o The DHCP server MUST NOT send both Binding Option(s) and
OPTION_MAP_RULE in a single OPTION_MAP response.
3.4. Forwarding Action by the Customer End-Node
For all modes, the longest prefix match algorithm MUST be enforced to
forward outbound IPv4 packets.
Specifically, this algorithm will:
o Always return the address of the AFTR for the DS-Lite mode.
o Always return the address of the lwAFTR for the binding mode.
o Return the next hop according to the pre-configured mapping rules
for the stateless mode (i.e., MAP-E).
4. Future Expansion of the Unified CPE Model
The mechanism that is described here can be extended to cater for
other IPv4 service continuity approaches, outside of those
specifically covered in this document. In order to achieve this, the
following rules MUST be applied (in addition to the generic CPE
bootstrapping logic described in section 3.2 above):
The mechanism in extended by defining a new combination of
configuration parameters, unique to that mode of operation so that
the CPE can unambiguously determine which service continuity mode to
configure. This could be based on a new combination of existing
parameters, or on new parameters that are specific to the new
continuity mode.
It is important to note that it is the presence, or absence of
configuration parameters that are used to extend the Unified CPE
model, not the value of any individual (or multiple) parameters.
5. Security Considerations
Except for the less efficient port randomization and routing loops
[RFC6324], stateless 4/6 solutions are expected to introduce no more
security vulnerabilities than stateful ones. Because of their
stateless nature, they may in addition, reduce denial of service
opportunities. Security considerations defined in Section 11 of
[RFC6333] should be taken into account.
6. IANA Considerations
This document does not require any action from IANA.
Boucadair, et al. Expires December 01, 2013 [Page 12]
Internet-Draft Generic v4 in v6 CPE Provisioning Profile May 2013
7. Acknowledgements
Many thanks to T. Tsou, O. Troan, W. Dec, M. Chen, for their
review and comments.
Special thanks to S. Krishnan for the suggestions and guidance.
8. References
8.1. Normative References
[I-D.ietf-softwire-lw4over6]
Cui, Y., Sun, Q., Boucadair, M., Tsou, T., Lee, Y., and I.
Farrer, "Lightweight 4over6: An Extension to the DS-Lite
Architecture", draft-ietf-softwire-lw4over6-00 (work in
progress), April 2013.
[I-D.ietf-softwire-map-dhcp]
Mrugalski, T., Troan, O., Dec, W., Bao, C.,
leaf.yeh.sdo@gmail.com, l., and X. Deng, "DHCPv6 Options
for Mapping of Address and Port", draft-ietf-softwire-map-
dhcp-03 (work in progress), February 2013.
[I-D.ietf-softwire-map]
Troan, O., Dec, W., Li, X., Bao, C., Matsushima, S.,
Murakami, T., and T. Taylor, "Mapping of Address and Port
with Encapsulation (MAP)", draft-ietf-softwire-map-07
(work in progress), May 2013.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2473] Conta, A. and S. Deering, "Generic Packet Tunneling in
IPv6 Specification", RFC 2473, December 1998.
[RFC4291] Hinden, R. and S. Deering, "IP Version 6 Addressing
Architecture", RFC 4291, February 2006.
[RFC6052] Bao, C., Huitema, C., Bagnulo, M., Boucadair, M., and X.
Li, "IPv6 Addressing of IPv4/IPv6 Translators", RFC 6052,
October 2010.
[RFC6333] Durand, A., Droms, R., Woodyatt, J., and Y. Lee, "Dual-
Stack Lite Broadband Deployments Following IPv4
Exhaustion", RFC 6333, August 2011.
8.2. Informative References
Boucadair, et al. Expires December 01, 2013 [Page 13]
Internet-Draft Generic v4 in v6 CPE Provisioning Profile May 2013
[I-D.ietf-dhc-dhcpv4-over-dhcpv6]
Sun, Q., Cui, Y., Siodelski, M., Krishnan, S., and I.
Farrer, "DHCPv4 over DHCPv6 Transport", draft-ietf-dhc-
dhcpv4-over-dhcpv6-00 (work in progress), April 2013.
[I-D.ietf-softwire-public-4over6]
Cui, Y., Wu, J., Wu, P., Vautrin, O., and Y. Lee, "Public
IPv4 over IPv6 Access Network", draft-ietf-softwire-
public-4over6-09 (work in progress), May 2013.
[I-D.ietf-softwire-stateless-4v6-motivation]
Boucadair, M., Matsushima, S., Lee, Y., Bonness, O.,
Borges, I., and G. Chen, "Motivations for Carrier-side
Stateless IPv4 over IPv6 Migration Solutions", draft-ietf-
softwire-stateless-4v6-motivation-05 (work in progress),
November 2012.
[RFC6334] Hankins, D. and T. Mrugalski, "Dynamic Host Configuration
Protocol for IPv6 (DHCPv6) Option for Dual-Stack Lite",
RFC 6334, August 2011.
Authors' Addresses
Mohamed Boucadair
France Telecom
Rennes
France
Email: mohamed.boucadair@orange.com
Ian Farrer
Deutsche Telekom
Germany
Email: ian.farrer@telekom.de
Simon Perreault (editor)
Viagenie
246 Aberdeen
Quebec QC G1R 2E1
Canada
Email: simon.perreault@viagenie.ca
Boucadair, et al. Expires December 01, 2013 [Page 14]
Internet-Draft Generic v4 in v6 CPE Provisioning Profile May 2013
Senthil Sivakumar (editor)
Cisco Systems
7100-8 Kit Creek Road
Research Triangle Park, North Carolina
USA
Email: ssenthil@cisco.com
Boucadair, et al. Expires December 01, 2013 [Page 15]