TRILL Working Group W. Hao
INTERNET-DRAFT Y. Li
Intended Status: Standard Track Huawei
A. Qu
MediaTec
M. Durrani
Cisco
P. Sivamurugan
IP Infusion
L. Xia
Huawei
Expires: January 06, 2016 July 06, 2015
TRILL Distributed Layer 3 Gateway
draft-ietf-trill-irb-06.txt
Abstract
Currently the TRILL protocol provides optimal pair-wise data frame
forwarding for layer 2 intra-subnet traffic but not for layer 3 inter-
subnet traffic. A centralized gateway solution is typically used for
layer 3 inter-subnet traffic forwarding but has the following issues:
1. Sub-optimum forwarding paths for inter-subnet traffic.
2. A centralized gateway may need to support a very large number of
gateway interfaces in a data center, one per tenant per data label used
by that tenant, to provide interconnect functionality for all the layer
2 virtual networks in entire TRILL network.
3. A traffic bottleneck at the gateway.
This document specifies an optional TRILL distributed gateway solution
that resolves these centralized gateway issues.
Status of this Memo
This Internet-Draft is submitted in full conformance with the provisions
of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering Task
Force (IETF), its areas, and its working groups. Note that other groups
may also distribute working documents as Internet-Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
Hao & Li, etc Expires January 6, 2016 [Page 1]
Internet-Draft TRILL Distributed Layer 3 Gateway July 2015
time. It is inappropriate to use Internet-Drafts as reference material
or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/1id-abstracts.html
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
Copyright Notice
Copyright (c) 2015 IETF Trust and the persons identified as the document
authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal Provisions
Relating to IETF Documents (http://trustee.ietf.org/license-info) in
effect on the date of publication of this document. Please review these
documents carefully, as they describe your rights and restrictions with
respect to this document. Code Components extracted from this document
must include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction................................................... 3
1.1. Document Organization......................................3
2. Conventions used in this document...............................3
3. Simplified Example and Problem Statement........................4
3.1. Distributed Gateway Simplified Example.....................5
3.2. Problem Statement..........................................6
4. Layer 3 Traffic Forwarding Model................................8
5. Distributed Gateway Solution Overview...........................8
5.1. Local routing information..................................9
5.2. Local routing information synchronization..................10
5.3. Active-active access.......................................12
5.4. Data traffic forwarding process............................12
6. Distributed Layer 3 Gateway Process Example.....................13
6.1. Control plane process......................................14
6.2. Data plane process ........................................15
7. TRILL Protocol Extensions ......................................16
7.1. The tenant Label and gateway MAC APPsub-TLV ...............16
7.2. "SE" Flag in NickFlags APPsub-TLV .........................17
Hao & Li, etc Expires January 6, 2016 [Page 2]
Internet-Draft TRILL Distributed Layer 3 Gateway July 2015
7.3. The IPv4 Prefix APPsub-TLV ................................17
7.4. The IPv6 Prefix APPsub-TLV.................................18
8. Security Considerations.........................................19
9. IANA Considerations ............................................19
10. Normative References ..........................................20
11. Informative References ........................................21
Acknowledgments .................................................. 21
Authors' Addresses ............................................... 21
1. Introduction
The TRILL (Transparent Interconnection of Lots of Links) protocol
[RFC6325] provides a solution for least cost transparent routing in
multi-hop networks with arbitrary topologies and link technologies,
using [IS-IS] [RFC7176] link-state routing and a hop count. TRILL
switches are sometimes called RBridges (Routing Bridges).
Currently, TRILL provides optimal unicast forwarding for Layer 2 intra-
subnet traffic but not for Layer 3 inter-subnet traffic, where subnet
means different IP address prefix and typically a different Data Label
(VLAN or FGL). In this document, an optional TRILL-based distributed
Layer 3 gateway solution is specified to provide optimal unicast
forwarding for Layer 3 inter-subnet traffic. With distributed gateway
support an edge RBridge provides both routing based on Layer 2 identity
(address and virtual network (VN, i.e. Data Label)) among end stations
(ESs) that belong to same subnet and routing based on Layer 3 identity
among ESs that belong to different subnets of the same routing domain.
An edge RBridge supporting this feature needs to provide routing
instances and Layer 3 gateway interfaces for local connected ESs. Such
routing instances provide IP address isolation between tenants. In the
TRILL distributed Layer 3 gateway solution, inter-subnet traffic can be
fully spread over edge RBridges, so there is no single bottleneck.
1.1. Document Organization
This document is organized as follows: Section 3 gives a simplified
example and more detailed problem statement. Section 4 gives the Layer 3
traffic forwarding model. Section 5 provides a distributed gateway
solution overview. Section 6 gives a detailed distributed gateway
solution example. And Section 7 describes the TRILL protocol extensions
needed to support this distributed gateway solution.
2. Conventions used in this document
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
Hao & Li, etc Expires January 6, 2016 [Page 3]
Internet-Draft TRILL Distributed Layer 3 Gateway July 2015
The terms and acronyms in [RFC6325] are used with the following
additions:
ARP: Address Resolution Protocol [RFC826].
Data Label: VLAN or FGL [RFC7172].
DCN: Data Center Network.
ES: End Station. VM (Virtual Machine) or physical server, whose
address is
either the destination or source of a data frame.
Gateway interface: Layer 3 virtual interface on gateway aka
gateway interface) terminates layer 2 forwarding and forwards IP traffic
to the destination as per IP forwarding rules. Incoming traffic from a
physical port on a gateway will be distributed to its virtual gateway
interface based on Data Label (VLAN or FGL).
L2: Layer 2.
L3: IP Layer 3.
ND: IPv6's Neighbor Discovery [RFC4861].
ToR: Top of Rack.
VN: Virtual Network. In a TRILL campus, each virtual network is
identified by a unique 12-bit VLAN ID or 24-bit Fine Grained Label
[RFC7172].
VRF: Virtual Routing and Forwarding. In IP-based computer networks,
Virtual Routing and Forwarding (VRF) is a technology that allows
multiple instances of a routing table to co-exist within the same router
at the same time.
3. Simplified Example and Problem Statement
Section 3.1 gives a simplified example in a TRILL campus with and without
a distributed layer 3 gateway using VLAN Data Labels. A more detailed
description of the problem without a distributed layer 3 gateway is given
in Section 3.2. The remainder of this document, particularly Section 5,
describes the distributed gateway solution in more detail.
Hao & Li, etc Expires January 6, 2016 [Page 4]
Internet-Draft TRILL Distributed Layer 3 Gateway July 2015
3.1. Distributed Gateway Simplified Example
Assuming a tenant has four subnets, each subnet corresponds to one VLAN
indicating one individual layer 2 virtual network, say the VLANs are VLAN
10 to VLAN 13, the end stations in VLAN 10 and VLAN 11 are connected to
RB1 and RB2, and the end stations(ESs) in VLAN 12 and VLAN 13 are
connected to RB3 and RB4. TRILL makes all end stations in each VLAN
appear to be on the same layer 2 link. Their layer 3 IP gateway also
appears as an end station on each link. Each tenant end station finds the
layer 3 gateway's MAC address by using ARP or ND to ask for the MAC
address corresponding to its IP router.
For traffic within a subnet, that is IP traffic to another end station in
the same VLAN attached to the TRILL campus, the end station just ARPs
for the MAC address for the destination end station's IP. It then uses
this MAC address for traffic to that destination and TRILL routes the
ingressed TRILL data packets to the destination's edge RBridge based on
the egress nickname for that destination MAC address and VLAN. This is
the regular process as defined in TRILL base protocol [RFC6325].
In centralized layer 3 gateway solution, all traffic within that tenant
between different VLANs must go through the centralized layer 3 gateway
device, say Gateway 1, even if the traffic is between two end stations
connected to the same edge RBridge, because only the layer 3 gateway can
change the VLAN labeling of the traffic. Gateway 1 has four gateway
interfaces for these four VLANs.
With the distributed layer 3 gateway, each edge RBridge acts as a default
layer 3 gateway for local connecting ESs, it also has IP router
capabilities to provide IP communication with other edge RBridges. Each
edge RBridge only needs gateway interfaces for local connecting ESs,
i.e., RB1 and RB2 have gateway interfaces for VLAN 10 and VLAN 11, RB3
and RB4 have gateway interfaces for VLAN 12 and VLAN 13. No RBridges
should normally need to maintain gateway interfaces all VLANs, because
each RBridge normally only supports a limited number of VNs. This will
enhance the scalability of tenants number and subnets number per tenant.
When each end station ARPs for their layer 3 gateway, that is, their IP
router, the edge RBridge to which it is connected will respond with
that RBridge's 'gateway MAC'. When the end station later sends IP traffic
to the layer 3 gateway, because the destination IP is outside of its
subnet, the edge RBridge intercepts the IP packet because the destination
MAC is its gateway MAC. That RBridge routes the IP packet using the
routing instance associated with that tenant, handling it in one of three
ways:
Hao & Li, etc Expires January 6, 2016 [Page 5]
Internet-Draft TRILL Distributed Layer 3 Gateway July 2015
(1) If the destination IP is connected to the same edge RBridge,
that RBridge can simply transmit the IP packet out the right edge port
in the destination VLAN.
(2) If the destination IP is located in an outside network, the edge
RBridge encapsulates it as a TRILL Data packet and sends it to the
actual TRILL campus edge RBridge connecting to the outside network.
(3) if the destination in an end station connected to a different
edge RBridge, the ingress RBridge uses TRILL encapsulation to route the
IP packet to the correct egress RBridge, using that RBridge's gateway MAC
and an Inner.VLAN identifying the tenant. Finally, the egress RBridge
terminates the TRILL encapsulation and routes the IP packet to the
destination end station based on the routing instance for that tenant.
Through the distributed layer 3 gateway solution, the inter-subnet
traffic are fully dispersed and are transmitted along optimal pair-wise
forwarding path, improving network efficiency.
3.2. Problem Statement
------- -------
| GW1 | | GW2 |
------- -------
| |
------- -------
|AGG1 | |AGG2 |
------- -------
| |
-----------------------------------------------------
| -------------|------------------|----------------|
| | | | | | | |
------- ------- ------- -------
|TOR1 | |TOR2 | |TOR3 | |TOR4 |
------- ------- ------- -------
| | | | | | | |
----- ----- ----- ----- ----- ----- ----- -----
|ES1| |ES2| |ES3| |ES4| |ES5| |ES6| |ES7| |ES8|
----- ----- ----- ----- ----- ----- ----- -----
Figure 1. A Typical DC Network
Figure 1 depicts a TRILL Data Center Network (DCN) where edge RBridges
are Top of Rack (ToR) switches. Centralized gateway GW1 and GW2 in
Hao & Li, etc Expires January 6, 2016 [Page 6]
Internet-Draft TRILL Distributed Layer 3 Gateway July 2015
figure 1 provide the layer 3 packet forwarding for both north-south
traffic and east-west inter-subnet traffic between ESs.
End stations in one IP subnet expect to send IP traffic for a different
subnet to an IP router. In addition, there is normally a Data Label
(VLAN or FGL) associated with each IP subnet but there is no facility
in the base TRILL protocol [RFC6325] to change the Data Label for traffic
between subnets. If two end stations of the same tenant are on two
different subnets and need to communicate with each other, their packets
are typically forwarded all the way to a centralized IP Layer 3 gateway
to perform L3 routing and, if necessary, change the Data Label.
This is generally sub-optimal because the two end stations may be
connected to the same ToR where L3 switching could have been performed
locally. For example, in above Figure 1, assuming ES1 (10.1.1.2 ) and ES2
(20.1.1.2) belong to different subnets of same tenant, the unicast IP
traffic between them has to go through a centralized gateway. It can't be
locally router between them on TOR1. However, if an edge RBridge has the
distributed gateway capabilities specified in this document, then it can
still perform optimum L2 forwarding for intra-subnet traffic and, in
addition, optimum L3 forwarding for inter-subnet traffic, thus
delivering optimum forwarding for unicast packets in all important cases.
With Fine Grained Labeling [RFC7172], in theory up to 16 million Layer 2
VN can be supported in a TRILL campus. To support inter- subnet traffic,
a very large number of Layer 3 gateway interfaces could be needed on a
centralized gateway if each VN corresponds to a subnet and there are
many tenant with many subnets per tenant. It is a big burden for the
centralized gateway to support so many interfaces. In addition all
inter-subnet traffic will go through the centralized gateway that may
become the traffic bottleneck.
In summary, the centralized gateway has the following issues:
1. Sub-optimum forwarding paths for inter-subnet traffic due to the
requirements to perform IP routing and possibly change Data Labels at a
centralized gateway.
2. The centralized gateway may need to support a very large number
of gateway interfaces, in a data center one per tenant per data label
used by that tenant, to provide interconnect functionality for all the
layer 2 virtual networks in entire TRILL network.
3. A traffic bottleneck at the centralized gateway.
A distributed gateway on edge RBridges addresses these issues.
Hao & Li, etc Expires January 6, 2016 [Page 7]
Internet-Draft TRILL Distributed Layer 3 Gateway July 2015
4. Layer 3 Traffic Forwarding Model
+---------------------------------------------+
| |
| +-----------+ +-----------+ |
| | Tenant n |---------| VRF n | |
| +------------+ | +------------+ | |
| | +-----+ | | | | | |
| | | VN1 | | | | | | |
| | +-----+ | | | VRF 1 | | |
| | .. +-------+ | | |
| | +-----+ | | | | | |
| | | VNm | | | | | | |
| | +-----+ | | | | | |
| | Tenant 1 |-+ | | | |
| +------------+ | | | |
| +------------+ +------------+ |
| |
| Edge RBridge |
+---------------------------------------------+
Figure 2. Edge RBridge Model as Distributed Gateway
In a data center network (DCN), each tenant has one or more Layer 2
virtual networks and, in normal cases, each tenant corresponds to one
routing domain. Normally each Layer 2 virtual network uses a different
Data Label and corresponds to one or more subnets.
Each Layer 2 virtual network in a TRILL campus is identified by a unique
12-bit VLAN ID or 24-bit Fine Grained Label [RFC7172]. Different
routing domains may have overlapping address space but need distinct
and separate routes. The end stations that belong to the same subnet
communicate through L2 forwarding, end systems of the same tenant that
belong to different subnets communicate through L3 routing.
Figure 2 depicts the model where there are n VRFs corresponding to n
tenants with each tenant having up to m segments/subnets (virtual
network).
5. Distributed Gateway Solution Overview
In the TRILL distributed gateway scenario, an edge RBridge must perform
Layer 2 routing for the ESs that are on the same subnet and IP routing
for the ESs that are on the different subnets of the same tenant.
As the IP address space in different routing domains can overlap, VRF
instances need to be created on each edge RBridge to isolate the IP
Hao & Li, etc Expires January 6, 2016 [Page 8]
Internet-Draft TRILL Distributed Layer 3 Gateway July 2015
forwarding process for different routing domains present on the edge
RBridge. A globally unique tenant ID identifies each routing domain.
The network operator should ensure the consistency of the tenant ID on
each edge RBridge for each routing domain. If a routing domain spreads
over multiple edge RBridges, routing information for the routing domain
must be synchronized among these edge RBridges to ensure the reachability
to all ESs in that routing domain. The Tenant ID is carried with the
routing information to differentiate the routing domains.
From the data plane perspective, all edge RBridges are connected to each
other via one or multiple TRILL hops, however they are always a single
IP hop away. When an ingress RBridge receives inter-subnet traffic from
a local ES whose destination MAC is the edge RBridge's gateway MAC, that
RBridge will perform Ethernet header termination and look up in its IP
routing table to route the traffic to the IP next hop. If the destination
ES is connected to a remote edge RBridge, the remote RBridge will be the
IP next hop for traffic forwarding. The ingress RBridge will perform
TRILL encapsulation for such inter-subnet traffic and route it to the
remote RBridge through the TRILL campus.
When that remote RBridge receives the traffic, it will decapsulate the
packet and then lookup in the RBridge's IP forwarding table to route it
to the destination ES. Through this method, TRILL with distributed
gateways provides pair-wise data routing for inter-subnet traffic.
5.1. Local routing information
An ES can be locally connected to an edge RBridges through a layer 2
network or externally connected through a layer 3 IP network.
If the ES is connected to an edge RBridge through a Layer 2 network,then
the edge RBridge must act as a Layer 3 Gateway for the ES. A gateway
interface should be established on the edge RBridge for the connecting
ES. Because the ESs in a subnet may be spread over multiple edge
RBridges, each of these edge RBridges should establish its gateway
interface for the subnet and these gateway interfaces on different edge
RBridges share the same gateway MAC and gateway IP address.
Before an ES starts to send inter-subnet traffic, it should acquire its
gateway's MAC through the ARP/ND process. Local connecting edge
RBridges that are supporting this distributed gateway feature always
respond with the gateway MAC address when receiving ARP/ND requests for
the gateway IP. Through the ARP/ND process, the edge RBridge can learn
the IP and MAC correspondence of a local ES connected to the edge RBridge
by Layer 2 and then generate local IP routing entries for the ES in the
corresponding routing domain.
Hao & Li, etc Expires January 6, 2016 [Page 9]
Internet-Draft TRILL Distributed Layer 3 Gateway July 2015
An IP router looks to TRILL like an ES. If a router/ES is located in an
external IP network, normally it provides access to one or more IP
prefixs. The router/ES should run an IP routing protocol with the
connecting TRILL edge Rbridge. The edge RBridge will learn the IP
prefixes behind the router/ES through the IP routing protocol, then the
RBridge will generate local IP routing entries in the corresponding
routing domain.
5.2. Local routing information synchronization
When a routing instance is created on an edge RBridge, the tenant ID,
tenant Label (VLAN or FGL), tenant gateway MAC, and their correspondence
should be set and globally advertised (see Section 7.1).
When an ingress RBridge performs inter-subnet traffic TRILL encapsulation,
the ingress RBridge uses the Label advertised by the egress RBridge as
the inner VLAN or FGL and uses the tenant gateway MAC advertised by the
egress RBridge as the Inner.MacDA. The egress RBridge relies on this
tenant Data Label to find the local VRF instance for the IP forwarding
process when receiving inter-subnet traffic from the TRILL campus. (The
role of tenant Label is akin to an MPLS VPN Label in an MPLS IP/MPLS VPN
network.) Tenant Data Labels are independently allocated on each edge
RBridge for each routing domain, an edge RBridge can pick up an access
Data Label in a routing domain to act as the inter-subnet Label, or the
edge RBridge can use a different Label from any access Labels to act as
tenant Label. It's implementation dependant and there is no restriction
on this. The tenant gateway MAC differentiates inter-subnet Layer 3
traffic or intra-subnet Layer 2 traffic on the egress RBridge. Each
tenant on a RBridge can use a different gateway MAC or same tenant
gateway MAC for inter-subnet traffic purposes. This is also
implementation dependant and there is no restriction on it.
When a local IP prefix is learned in a routing instance on an edge
RBridge, the edge RBridge should advertise the IP prefix information
for the routing instance to other edge RBridges to generate IP routing
entries. If the ESs in a VN are spread over multiple RBridges, these
RBridges should advertise each local connecting end station's IP address
in the VN to other RBridges. If the ESs in a VN are only connected to one
edge RBridge, that RBridge only needs to advertise the subnet
corresponding to the VN to other RBridges. A globally unique tenant ID
also should be carried to differentiate IP prefixes between different
tenants, because the IP address space of different tenants can overlap
(see Sections 7.3 and 7.4).
If a tenant is deleted on an edge Rbridge, the edge Rbridge should notify
all other edge Rbridges to delete local IP prefixs, tenant Label and
tenant gateway MAC. If there is a new tenant which is created and the
Hao & Li, etc Expires January 6, 2016 [Page 10]
Internet-Draft TRILL Distributed Layer 3 Gateway July 2015
original's tenant label is assigned to the new tenant immediately, it may
cause a security policy violation for the traffic in flight, because when
the egress Rbridge receives traffic from the old tenant, it will forward
it in the new tenant's routing instance and deliver it to wrong
destination. So tenant Label MUST NOT be re-allocated until a reasonable
amount of time has passed to allow any traffic in flight to be discarded.
When the ARP entry in an edge Rbridge for an ES times out, it will
trigger an edge Rbridge LSP advertisement to other edge Rbridges with
the corresponding IP routing entry deleted. If the ES is an IP router,
the edge Rbridge also notifies other edge Rbridges that they must delete
the routing entries corresponding to the IP prefixs accessible through
that IP router. During the IP prefix deleting process, if there is
traffic in flight, the traffic will be discarded at the egress Rbridge
because there is no local IP routing entry to the destination.
If an edge Rbridge changes its tenant gateway MAC, it will trigger an
edge Rbridge LSP advertisement to other edge Rbridges giving the new
gateway MAC as Inner.MacDA for future traffic destined to the edge
Rbridge. During the gateway MAC changing process, if there is traffic
in flight using the old gateway MAC as Inner.MacDA, the traffic will be
discarded or be forwarded as layer 2 intra-subnet traffic on the edge
Rbridge. If the inter-subnet tenant Label is a unique Label which is
different from any access Labels, when the edge Rbridge receives the
traffic whose Inner.MacDA is different from local tenant gateway MAC, the
traffic will be discarded. If the edge RBridge uses one of the access
Labels as inter-subnet tenant Label, the traffic will be forwarded as
layer 2 intra-subnet traffic unless special traffic filtering policy is
enforced on the edge Rbridge.
If there are multiple nicknames owned by an edge RBridge, the edge
RBridge also can specify one nickname as the egress nickname for inter-
subnet traffic forwarding. A NickFlags APPsub-TLV with the SE-flag set
can be used for this purpose. If the edge RBridge doesn't specify a
nickname for this purpose, the ingress RBridge can use any one of the
nicknames owned by the egress as the egress nickname for inter-subnet
traffic forwarding.
TRILL E-L1FS FS-LSP [rfc7180bis] APPsub-TLVs can be used for IP routing
information synchronization in each routing domain among edge RBridges.
Based on the synchronized information from other edge RBridges, each edge
RBridge generates remote IP routing entries in each routing domain.
Through this solution, the intra-subnet forwarding function and inter-
subnet IP routing functions are integrated and network management and
deployment will be simplified.
Hao & Li, etc Expires January 6, 2016 [Page 11]
Internet-Draft TRILL Distributed Layer 3 Gateway July 2015
5.3. Active-active access
TRILL active-active service provides end stations with flow level load
balance and resilience against link failures at the edge of TRILL
campuses as described in [RFC7379].
If an ES is connected to two TRILL RBridges, say RB1 and RB2, in active-
active mode, RB1 and RB2 can act as distributed layer 3 gateway for the
ES. RB1 and RB2 each learn the ES's IP address through ARP/ND process
and then they announce the IP address to the TRILL campus independently.
The remote ingress RBridge will generate an IP routing entry
corresponding with the IP address with two IP next hops of RB1 and RB2.
When the ingress RBridge receives inter-subnet traffic from a local
access network, the ingress RBridge selects RB1 or RB2 as the IP next
hop based on local load balancing algorithm, then the traffic will be
transmitted to the selected next hop destination RB1 or RB2 through the
TRILL campus.
5.4. Data traffic forwarding process
After a Layer 2 connected ES1 in VLAN-x acquires its gateway's MAC, it
can start inter-subnet data traffic transmission to ES2 in VLAN-y.
When the edge RBridge attached to ES1 receives inter-subnet traffic from
ES1, that RBridge performs Layer 2 header termination, then, using the
local VRF corresponding to VLAN-x, it performs the IP routing process in
that VRF.
If destination ES2 is attached to the same edge RBridge, the traffic will
be locally forwarded to ES2 by that RBridge. Compared to the
centralized gateway solution, the forwarding path is optimal and a
traffic detour is avoided.
If ES2 is attached to a remote edge RBridge, the remote edge RBridge is
IP next hop and the inter-subnet traffic is forwarded to the IP next
hop through TRILL encapsulation. If there are multiple equal cost
shortest path between ingress RBridge and egress RBridge, all these
path can be used for inter-subnet traffic forwarding, so load spreading
can be achieved for inter-subnet traffic.
When the remote RBridge receives the inter-subnet TRILL encapsulated
traffic, the RBridge decapsulates the TRILL encapsulation and checks
the Inner.MacDA, if that MAC address is the local gateway MAC
corresponding to the inner Label (VLAN or FGL), the inner Label will be
used to find the corresponding local VRF, then the IP routing process in
Hao & Li, etc Expires January 6, 2016 [Page 12]
Internet-Draft TRILL Distributed Layer 3 Gateway July 2015
that VRF will be performed, and the traffic will be locally forwarded to
the destination ES2.
In summary, this solution avoids traffic detours through a central
gateway, both inter-subnet and intra-subnet traffic can be forwarded
along pair-wise shortest paths, and network bandwidth is conserved.
6. Distributed Layer 3 Gateway Process Example
This section gives a detailed description of a distributed layer 3
gateway solution example.
--------- ---------
| RB3 | | RB4 |
--------- ---------
# * *
# **************************
########################### *
# * # *
# * # *
# * # *
--------- ---------
| RB1 | | RB2 |
--------- ---------
| |
----- -----
|ES1| |ES2|
----- -----
Figure 3. Distributed gateway scenario
In figure 3, RB1 and RB2 support the distribution gateway function, ES1
connects to RB1, ES2 connects to RB2. ES1 and ES2 belong to Tenant1,
but are in different subnets.
The IP address, VLAN, and subnet information of ES1 and ES2 are as
follows:
+----+---------+----------------+---------------+----------+
| ES | Tenant | IP Address | Subnet | VLAN |
+----+---------+----------------+---------------+----------+
| ES1| Tenant1 | 10.1.1.2 | 10.1.1.1/32 | 10 |
+----+---------+----------------+---------------+----------+
| ES2| Tenant1 | 20.1.1.2 | 20.1.1.1/32 | 20 |
+----+---------+----------------+---------------+----------+
Figure 4. ES information
The nickname, VRF, tenant VLAN, tenant gateway MAC for Tenant1 on RB1 and
RB2 are as follows:
Hao & Li, etc Expires January 6, 2016 [Page 13]
Internet-Draft TRILL Distributed Layer 3 Gateway July 2015
+----+---------+----------+-------+--------------+--------------+
| RB | Nickname| Tenant | VRF | Tenant VLAN | Gateway MAC |
+----+---------+----------+-------+--------------+--------------+
| RB1| nick1 | Tenant1 | VRF1 | 100 | MAC1 |
+----+---------+----------+-------+--------------+--------------+
| RB2| nick2 | Tenant1 | VRF2 | 100 | MAC2 |
+----+---------+----------+-------+--------------+--------------+
Figure 5. RBridge information
6.1. Control plane process
RB1 announces the following local routing information to the TRILL campus:
Tenant ID: 1
Tenant gateway MAC: MAC1
Tenant VLAN for Tenant1: VLAN 100.
IP prefix in Tenant1: 10.1.1.2/32.
RB2 announces the following local routing information to TRILL campus:
Tenant ID: 1
Tenant gateway MAC: MAC2
Tenant VLAN for Tenant1: VLAN 100.
IP prefix in Tenant1: 20.1.1.2/32.
Relying on the routing information from RB2, remote routing entries on
RB1 are generated as follows:
+--------------+-------------+--------------+----------------+
| Prefix/Mask | Inner.MacDA | inner VLAN | egress nickname|
+--------------+-------------+--------------+----------------+
| 20.1.1.2/32 | MAC2 | 100 | nick2 |
+--------------+-------------+--------------+----------------+
Figure 6. Tenant 1 remote routing table on RB1
Similarly, relying on the routing information from RB1, remote routing
entries on RB2 are generated as follows:
+-----------+-------------+-----------+---------------+
|Prefix/Mask| Inner.MacDA |inner VLAN |egress nickname|
+-----------+-------------+-----------+---------------+
Hao & Li, etc Expires January 6, 2016 [Page 14]
Internet-Draft TRILL Distributed Layer 3 Gateway July 2015
|10.1.1.2/32| MAC1 | 100 | nick1 |
+-----------+-------------+-----------+---------------+
Figure 7. Tenant 1 remote routing table on RB1
6.2. Data plane process
Assuming ES1 sends unicast inter-subnet traffic to ES2, the traffic
forwarding process is as follows:
1. ES1 sends unicast inter-subnet traffic to RB1 with RB1's gateway's
MAC as the destination MAC.
2. Ingress RBridge (RB1) forwarding process:
RB1 checks the destination MAC, if the destination MAC equals the local
gateway MAC, the gateway function will terminate the Layer 2 header and
perform L3 routing.
RB1 looks up IP routing table information by destination IP and Tenant ID
to get IP next hop information, which includes the egress RBridge's
gateway MAC (MAC2), tenant VLAN (VLAN 100) and egress nickname (nick2).
Using this information, RB1 will perform inner Ethernet header
encapsulation and TRILL encapsulation. RB1 will use MAC2 as the
Inner.MacDA, MAC1 (RB1's own gateway MAC) as the Inner.MacSA, VLAN 100 as
the Inner.VLAN, nick2 as the egress nickname and nick1 as the ingress
nickname.
RB1 looks up TRILL forwarding information by egress nickname and sends
the traffic to the TRILL next hop as per [RFC6325]. The traffic will be
sent to RB3 or RB4 as a result of load balancing.
Assuming the traffic is forwarded to RB3, the following occurs:
3. Transit RBridge (RB3) forwarding process:
RB3 looks up TRILL forwarding information by egress nickname and forwards
the traffic to RB2 as per [RFC6325].
4. Egress RBridge forwarding process:
As the egress nickname is RB2's own nickname, RB2 performs TRILL
decapsulation. Then it checks the Inner.MacDA and, because that MAC is
equal to the local gateway MAC, performs inner Ethernet header
termination. Using the inner VLAN, RB2 finds the local corresponding VRF
and looks up the packets destination IP address in the VRF's IP routing
table. The traffic is then be locally forwarded to ES2.
Hao & Li, etc Expires January 6, 2016 [Page 15]
Internet-Draft TRILL Distributed Layer 3 Gateway July 2015
7. TRILL Protocol Extensions
If an edge RBridge RB1 participates in the distributed gateway function,
it announces its tenant gateway MAC and tenant Data Label to the TRILL
campus through the tenant Label and gateway MAC APPsub-TLV, it should
announce its local IPv4 and IPv6 prefixs through the IPv4 Prefix
APPsub-TLV and the IPv6 Prefix APPsub-TLV respectively. If RB1 has
multiple nicknames, it can announce one nickname for distributed
gateway use using Nickname Flags APPsub-TLV with "SE" Flag set to one.
The remote ingress RBridges belonging to the same routing domain use this
information to generate IP routing entries in that routing domain. These
RBridges use the nickname, tenant gateway MAC and tenant Label of RB1
to perform inter-subnet traffic TRILL encapsulation when they receive
inter-subnet traffic from a local ES. The nickname is used as the
egress nickname, the tenant gateway MAC is used as the Inner.MacDA, and
the tenant Data Label is used as the Inner.Label. The following APPsub-
TLVs MUST be included in a TRILL GENINFO TLV in E-L1FS FS-LSPs
[rfc7180bis].
7.1. The tenant Label and gateway MAC APPsub-TLV
+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | (2 bytes)
+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Length | (2 bytes)
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Tenant ID (4 bytes) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|Resv1| Label1 | (2 bytes)
+-+-+-+-+-+-+-+-+-+-+-+-+
|Resv2| Label2 | (2 bytes)
+-+-+-+-+-+-+-+-+-+-+-+-+....-+-+-+-+-+-+-+-+-+-+
| Tenant Gateway Mac (6 bytes) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
o Type: Set to TENANT-LABEL sub-TLV type (TBD1). Two bytes, because
this APPsub-TLV appears in an extended TLV [RFC7356].
o Length: If Label1 field is used to represent a VLAN, the value of
the length field is 12. If Label1 and Label2 field are used to
represent an FGL, the value of the length field is 14.
o Tenant ID: This identifies a global tenant ID.
Hao & Li, etc Expires January 6, 2016 [Page 16]
Internet-Draft TRILL Distributed Layer 3 Gateway July 2015
o Resv1: 4 bits that MUST be sent as zero and ignored on receipt.
o Label1: If the value of the length field is 12, it identifies a
tenant VLAN ID, If the value of the length field is 14, it identifies
the higher 12 bits of a tenant FGL.
o Resv2: 4 bits that MUST be sent as zero and ignored on receipt.
Only present if the length field is 14.
o Label2: This field has the lower 12 bits of tenant FGL. Only
present if the length field is 14.
o Tenant Gateway MAC: This identifies the local gateway MAC
corresponding to the tenant ID. The remote ingress RBridges use the
Gateway MAC as Inner.MacDA. The advertising TRILL RBridge uses the
gateway MAC to differentiate layer 2 intra-subnet traffic and layer 3
inter-subnet traffic in the egress direction.
7.2. "SE" Flag in NickFlags APPsub-TLV
The NickFlags APPsub-TLV is specified in [rfc7180bis]. The SE Flag
is assigned as follows:
+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+
| Nickname |
+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+
|IN|SE| RESV |
+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+
NICKFLAG RECORD
o SE. If the SE flag is one, it indicates that the advertising
RBridge suggests the nickname should be used as the Inter-Subnet Egress
nickname for inter-subnet traffic forwarding. If flag is zero, that
nickname will not be used for that purpose.
7.3. The IPv4 Prefix APPsub-TLV
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | (2 bytes)
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Total Length | (2 bytes)
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+...-+-+-+-+-+-+-+-+
| Tenant ID |(4 bytes)
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+...-+-+-+-+-+-+-+-+
| Prefix Length(1)| (1 byte)
Hao & Li, etc Expires January 6, 2016 [Page 17]
Internet-Draft TRILL Distributed Layer 3 Gateway July 2015
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+...-+-+-+-+-+-+-+-+
| Prefix (1) |(variable)
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+...-+-+-+-+-+-+-+-+
| ..... | (1 byte)
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+...-+-+-+-+-+-+-+-+
| ..... |(variable)
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+...-+-+-+-+-+-+-+-+
| Prefix Length(N)| (1 byte)
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+...-+-+-+-+-+-+-+-+
| Prefix (N) |(variable)
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+...-+-+-+-+-+-+-+-+
o Type: Set to IPV4-PREFIX sub-TLV type (TBD2). Two bytes, because
this APPsub-TLV appears in an extended TLV [RFC7356].
o Total Length: This 2-byte unsigned integer indicates the total
length of the Tenant ID, the Prefix Length, and the Prefix fields in
octets. A value of 0 indicates that no IPv4 prefix is being advertised.
o Tenant ID: This identifies a global tenant ID.
o Prefix Length: The Prefix Length field indicates the length in
bits of the IPv4 address prefix. A length of zero indicates a prefix
that matches all IPv4 addresses (with prefix, itself, of zero octets).
o Prefix: The Prefix field contains an IPv4 address prefix,
followed by enough trailing bits to make the end of the field fall on
an octet boundary. Note that the value of the trailing bits is
irrelevant. For example, if the Prefix Length is 12, indicating 12 bits,
then the Prefix is 2 octets and the low order 4 bits of the Prefix are
irrelevant.
7.4. The IPv6 Prefix APPsub-TLV
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | (2 bytes)
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Total Length | (2 bytes)
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+...-+-+-+-+-+-+-+-+
| Tenant ID |(4 bytes)
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+...-+-+-+-+-+-+-+-+
| Prefix Length(1)| (1 byte)
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+...-+-+-+-+-+-+-+-+
| Prefix (1) |(variable)
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+...-+-+-+-+-+-+-+-+
| ..... | (1 byte)
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+...-+-+-+-+-+-+-+-+
| ..... |(variable)
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+...-+-+-+-+-+-+-+-+
Hao & Li, etc Expires January 6, 2016 [Page 18]
Internet-Draft TRILL Distributed Layer 3 Gateway July 2015
| Prefix Length(N)| (1 byte)
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+...-+-+-+-+-+-+-+-+
| Prefix (N) |(variable)
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+...-+-+-+-+-+-+-+-+
o Type: Set to IPV6-PREFIX sub-TLV type (TBD3). Two bytes, because
this APPsub-TLV appears in an extended TLV [RFC7356].
o Total Length: This 2-byte unsigned integer indicates the total
length of the Tenant ID, the Prefix Length, and the Prefix fields in
octets. A value of 0 indicates that no IPv6 prefix is being advertised.
o Tenant ID: This identifies a global tenant ID.
o Prefix Length: The Prefix Length field indicates the length in
bits of the IPv6 address prefix. A length of zero indicates a prefix
that matches all IPv6 addresses (with prefix, itself, of zero octets).
o Prefix: The Prefix field contains an IPv6 address prefix,
followed by enough trailing bits to make the end of the field fall on
an octet boundary. Note that the value of the trailing bits is
irrelevant. For example, if the Prefix Length is 100, indicating 100 bits,
then the Prefix is 13 octets and the low order 4 bits of the Prefix are
irrelevant.
8. Security Considerations
Correct configuration of the edge RBridges participating is important to
assure that data is not delivered to the wrong tenant, which would
violate security constrains. IS-IS security [RFC5310] can be used to
secure the information advertised by the edge RBridges in LSPs and FS-
LSPs.
Particularly sensitive data should be encrypted end-to-end, that is, from
the source end station to the destination end station.
For general TRILL Security Considerations, see [RFC6325].
9. IANA Considerations
IANA is requested to assign three APPsub-TLV type numbers less than 255
and update the "TRILL APPsub-TLV Types under IS-IS TLV 251 Application
Identifier 1" registry as follows:
Type Name References
Hao & Li, etc Expires January 6, 2016 [Page 19]
Internet-Draft TRILL Distributed Layer 3 Gateway July 2015
---- ---------------- ------------
TBD1 TENANT-GWMAC-LABEL [this document]
TBD2 IPV4-PREFIX [this document]
TBD3 IPV6-PREFIX [this document]
IANA is requested to assign a flag bit in the NickFlags APPsub-TLV as
described in Section 7.2 and update the registry created by Section
11.2.3 of [rfc7180bis] as follows:
Bit Mnemonic Description Reference
----- -------- ------------------- -----------
1 SE Inter-Subnet Egress [this document]
10. Normative References
[IS-IS] - ISO/IEC, "Intermediate system to Intermediate system routeing
information exchange protocol for use in conjunction with the Protocol
for providing the Connectionless-mode Network Service (ISO 8473)",
ISO/IEC 10589:2002.
[RFC2119] - Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, April 1997.
[RFC6325] - Perlman, R., Eastlake 3rd, D., Dutt, D., Gai, S., and
A.Ghanwani, "Routing Bridges (RBridges): Base Protocol Specification",
RFC 6325, July 2011.
[RFC7172] - Eastlake, D., M. Zhang, P. Agarwal, R. Perlman, D. Dutt,
"TRILL (Transparent Interconnection of Lots of Links): Fine-Grained
Labeling", RFC7172, May 2014.
[RFC7176] - Eastlake, D., T. Senevirathne, A. Ghanwani, D. Dutt and A.
Banerjee" Transparent Interconnection of Lots of Links (TRILL) Use of IS-
IS", RFC7176, May 2014.
[RFC7356] - Ginsberg, L., Previdi, S., and Y. Yang, "IS-IS Flooding Scope
Link State PDUs (LSPs)", RFC 7356, September 2014, <http://www.rfc-
editor.org/info/rfc7356>.
[RFC7357] - Zhai, H., Hu, F., Perlman, R., Eastlake 3rd, D., and O.
Stokes, "Transparent Interconnection of Lots of Links (TRILL): EndStation
Hao & Li, etc Expires January 6, 2016 [Page 20]
Internet-Draft TRILL Distributed Layer 3 Gateway July 2015
Address Distribution Information (ESADI) Protocol", RFC 7357, September
2014, <http://www.rfc-editor.org/info/rfc7357>.
[rfc7180bis] - Eastlake, D., et al, "TRILL: Clarifications, Corrections,
and Updates", draft-ietf-trill-rfc7180bis, work in progress.
11. Informative References
[RFC826] - Plummer, D., "Ethernet Address Resolution Protocol: Or
Converting Network Protocol Addresses to 48.bit Ethernet Address for
Transmission on Ethernet Hardware", STD 37, RFC 826, November 1982,
<http://www.rfc-editor.org/info/rfc826>.
[RFC4861] - Narten, T., Nordmark, E., Simpson, W., and H. Soliman,
"Neighbor Discovery for IP version 6 (IPv6)", RFC 4861, September 2007,
<http://www.rfc-editor.org/info/rfc4861>.
[RFC5310] - Bhatia, M., Manral, V., Li, T., Atkinson, R., White, R., and
M. Fanto, "IS-IS Generic Cryptographic Authentication", RFC 5310,
February 2009.
[RFC7379] - Li, Y., Hao, W., Perlman, R., Hudson, J., and H. Zhai,
"Problem Statement and Goals for Active-Active Connection at the
Transparent Interconnection of Lots of Links (TRILL) Edge", RFC 7379,
October 2014, <http://www.rfc-editor.org/info/rfc7379>.
Acknowledgments
The authors wish to acknowledge the important contributions of Donald
Eastlake, Gayle Noble, Guangrui Wu, Zhenbin Li, Zhibo Hu.
Authors' Addresses
Weiguo Hao
Huawei Technologies
101 Software Avenue,
Nanjing 210012, China
Phone: +86-25-56623144
Email: haoweiguo@huawei.com
Yizhou Li
Huawei Technologies
101 Software Avenue,
Nanjing 210012, China
Phone: +86-25-56625375
Hao & Li, etc Expires January 6, 2016 [Page 21]
Internet-Draft TRILL Distributed Layer 3 Gateway July 2015
Email: liyizhou@huawei.com
Andrew Qu
MediaTec
Email: laodulaodu@gmail.com
Muhammad Durrani
Cisco
Email: mdurrani@cisco.com
Ponkarthick Sivamurugan
Address: IP Infusion,
RMZ Centennial
Mahadevapura Post
Bangalore - 560048
Email: Ponkarthick.sivamurugan@ipinfusion.com
Liang Xia(Frank)
Huawei Technologies
101 Software Avenue,
Nanjing 210012, China
Phone: +86-25-56624539
Email: frank.xialiang@huawei.com
Hao & Li, etc Expires January 6, 2016 [Page 22]