Network Working Group                                             J. Ott
Internet-Draft                                                       TUM
Intended status: Standards Track                                 R. Even
Expires: March 5, 2018                                            Huawei
                                                              C. Perkins
                                                   University of Glasgow
                                                                V. Singh
                                                       September 1, 2017

                             RTP over QUIC


   QUIC is a UDP-based protocol for congestion controlled reliable data
   transfer, while RTP serves carrying (conversational) real-time media
   over UDP.  This draft discusses design aspects and issues of carrying
   RTP over QUIC.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on March 5, 2018.

Copyright Notice

   Copyright (c) 2017 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   ( in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect

Ott, et al.               Expires March 5, 2018                 [Page 1]

Internet-Draft                RTP over QUIC               September 2017

   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   2
   2.  Use Cases for RTP over QUIC . . . . . . . . . . . . . . . . .   3
   3.  RTP-to-Transport Interface  . . . . . . . . . . . . . . . . .   4
   4.  RTP-to-QUIC Mapping . . . . . . . . . . . . . . . . . . . . .   5
     4.1.  Mapping Semantic Units  . . . . . . . . . . . . . . . . .   6
     4.2.  Encapsulating Media Units . . . . . . . . . . . . . . . .   6
     4.3.  Mapping Media to Streams  . . . . . . . . . . . . . . . .   7
     4.4.  Mapping RTCP packets  . . . . . . . . . . . . . . . . . .   8
     4.5.  Mapping of RTP header extensions  . . . . . . . . . . . .   9
   5.  Design considerations for QUIC  . . . . . . . . . . . . . . .   9
     5.1.  Reliability (or restransmission) control for stream
           frames  . . . . . . . . . . . . . . . . . . . . . . . . .   9
     5.2.  Congestion control adaptation . . . . . . . . . . . . . .  10
     5.3.  RTCP mapping  . . . . . . . . . . . . . . . . . . . . . .  10
     5.4.  API . . . . . . . . . . . . . . . . . . . . . . . . . . .  10
     5.5.  Multiparty  . . . . . . . . . . . . . . . . . . . . . . .  11
   6.  SDP Extensions for Negotiating RTP-over-QUIC  . . . . . . . .  11
   7.  Security Considerations . . . . . . . . . . . . . . . . . . .  11
   8.  IANA Considerations . . . . . . . . . . . . . . . . . . . . .  11
   9.  Acknowledgments . . . . . . . . . . . . . . . . . . . . . . .  12
   10. References  . . . . . . . . . . . . . . . . . . . . . . . . .  12
     10.1.  Normative References . . . . . . . . . . . . . . . . . .  12
     10.2.  Informative References . . . . . . . . . . . . . . . . .  12
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  15

1.  Introduction

   The Real-time Transport Protocol (RTP) [RFC3550] provides a framework
   for delivery of audio and video data for telephony, teleconferencing,
   video streaming, TV distribution, and other real-time applications.
   Previous work has defined the RTP data transfer protocol, along with
   numerous profiles, payload formats, and other extensions.

   The QUIC transport protocol [I-D.ietf-quic-transport]
   [I-D.ietf-quic-tls] [I-D.ietf-quic-recovery]
   [I-D.ietf-quic-manageability] [I-D.ietf-quic-applicability]
   [I-D.ietf-quic-http] is a UDP-based, stream-multiplexing, encrypted
   transport protocol, primarily targeting web applications.  When
   compared to the combination of TCP and TLS, QUIC reduced connection
   set-up times, improved congestion control, and stream multiplexing
   without head-of-line blocking.

Ott, et al.               Expires March 5, 2018                 [Page 2]

Internet-Draft                RTP over QUIC               September 2017

   RTP has typically been run over UDP or DTLS [RFC5763] [RFC5764], to
   leverage timely but unreliable data transfer as part of interactive
   application frameworks such as SIP [RFC3261] and WebRTC
   [I-D.ietf-rtcweb-overview] [I-D.ietf-rtcweb-rtp-usage], or to build
   on UDP/IP multicast support for large-scale managed TV distribution.
   A mapping of RTP onto TCP [RFC4571] has been widely used for video on
   demand applications using RTSP [RFC7826], although with relaxed delay
   bounds [Delay-TCP].  There is also an experimental mapping of RTP
   onto DCCP [RFC5762].  This memo explores how RTP can be run over
   QUIC.  It has four main purposes:

   1.  to document use cases for RTP over QUIC, and to help understand
       when it's appropriate to use RTP and QUIC together (Section 2;
   2.  to understand and define a sensible mapping of RTP sessions onto
       one (or more) QUIC connections (Section 4);
   3.  to derive a wish-list for additional QUIC functionality to be fed
       into the QUIC WG (Section 5); and
   4.  to define the necessary signalling extensions to allow
       negotiation of RTP over QUIC (Section 6).

   Editor's note: Section 5 is intended to document requirements for now
   and may disappear later if those are met or formally folded into a
   separate document.  Also Section 4 and Section 6 may ultimately
   become separate drafts for consideration by different working groups
   (e.g., AVTCORE and MMUSIC).

2.  Use Cases for RTP over QUIC

   We identify the following possible use cases for RTP over QUIC:

   1.  Interactive peer-to-peer applications, such as telephony or video
       conferencing.  Such applications operate in a trapezoid topology
       using a client-server signalling channel running SIP or WebRTC,
       and an associated peer-to-peer media path and/or data channel.
       Mappings of SIP and WebRTC onto QUIC are possible, but outside
       the scope of this memo.  It might be desirable to transport the
       peer-to-peer RTP media path and data channel using QUIC, to
       leverage QUIC's security, stream demultiplexing, and congestion
       control features running over a single UDP port.  This would
       simplify media demultiplexing, and potentially obviate the need
       for the congestion control work being done in the RMCAT working
       group.  The design of QUIC makes it difficult however, since QUIC
       does not support peer-to-peer NAT traversal using STUN and ICE
       (and indeed uses a packet format that conflicts with STUN).
       These applications require low latency congestion control, and
       would benefit from unreliable delivery modes.
   2.  Interactive client-server applications.  For example, a "click
       here to speak to a representative" button on a website that

Ott, et al.               Expires March 5, 2018                 [Page 3]

Internet-Draft                RTP over QUIC               September 2017

       starts an interactive WebRTC call.  Such applications avoid the
       NAT traversal issues that complicate peer-to-peer use of QUIC,
       and can benefit from stream demultiplexing and (if appropriate
       algorithms are provided) congestion control.  They would benefit
       from unreliable delivery modes to reduce latency.
   3.  Client-server video on demand applications using WebRTC or RTSP.
       These benefit from QUIC stream demultiplexing in the same way as
       interactive client-server applications, but with relaxed latency
       bounds that make them fit better with existing congestion control
       algorithms and reliable delivery.
   4.  Live video streaming from a server can also benefit from stream
       demultiplexing.  If designed carefully, it should be easier to
       gateway RTP over QUIC into multicast RTP for scalable delivery
       than to gateway HTTP adaptive video over QUIC into multicast.

3.  RTP-to-Transport Interface

   The Real-time Transport Protocol defines the notion of RTP sessions
   to describe an elementary communication relationship between two or
   more parties.  An RTP session comprises a uni-, bi-, or
   multidirectional flow of RTP packets carrying media as well as flows
   of RTCP packets providing feed forward from RTP senders to receivers
   and feedback from RTP receivers to senders.

   Each media source is identified by a 32-bit Synchronization Source
   (SSRC) identifier, unique within an RTP session.  An RTP session
   comprise the set of media sources that have the same view of the SSRC
   space.  A single endpoint may use multiple SSRC identifiers (e.g.,
   one for audio and one for video).  Multiple media streams of a single
   endpoint are tied together by means of a common Canonical Name
   (CNAME) carried as part of the RTCP Source Description (SDES)
   packets.  This allows receivers to, e.g., determine which media
   streams to synchronize.

   Originally, in an RTP session the RTP and RTCP streams each used
   different port numbers, so that a single RTP session would use two
   port numbers (historically, when used with multicast conferencing,
   these were adjacent port numbers, RTP on the even and RTCP on the
   next higher odd port number).  However, the use of unicast RTP has,
   (not just) due to the presence of NATs, motivated the multiplexing of
   both RTP and RTCP on a single port number [RFC5761].  The payload
   structure and number spaces used for RTP and RTCP packets were
   designed to support this easily.

   The bundle framework [I-D.ietf-mmusic-sdp-bundle-negotiation] allows
   multiplexing of multiple RTP streams on a single address:port
   combination.  All the RTP streams in a bundled group are part of a
   single RTP session sharing a single SSRC number space [RFC3550].

Ott, et al.               Expires March 5, 2018                 [Page 4]

Internet-Draft                RTP over QUIC               September 2017

   These two efforts also reduce the number of ICE candidates to be
   validated as part of a multimedia call or conference setup procedure.
   They are particularly required in conjunction with WebRTC to reduce
   the signaling and resource requirements, which would affect NATs as
   well as STUN and TURN servers.  We note, however, that ICE is not
   currently usable with QUIC, since QUIC and STUN packets are not
   readily distinguished on a single UDP port, due to poor choice of
   packet formats.

   WebRTC deserves particular consideration because its potential close
   relationship to QUIC: WebRTC uses HTTP/1.1 (possibly using
   WebSockets), or HTTP/2 to connect to web servers, and thus will
   likely use QUIC in the future as a signaling transport.  Moreover,
   WebRTC supports peer-to-peer data channels, which currently target
   using SCTP over UDP over DTLS: SCTP for stream multiplexing within a
   connection and UDP for better NAT traversal properties.  Since QUIC
   would seem to support these two functions, it could be a natural
   choice to be used for the data channel as well - although this would
   require changes to the QUIC packet formats to allow demultiplexing
   with STUN for NAT traversal.

   For the actual media transmission, RTP use codec-specific payload
   formats that define how a piece of encoded media is broken down into
   data units that can fit into an MTU-sized packet for transmission.
   One important goal of RTP payload format design is allowing decoding
   packets as much as possible independent of each other as some may be
   lost due to the best-effort nature of the underlying UDP [RFC2736].
   This implies, on the one hand, that RTP senders have to perform
   codec-level fragmentation in a semantically meaningful manner and, on
   the other hand, that are in control of packet boundaries and
   transmission scheduling and timing as well as retransmission

   On the receiving side, RTP expects a detailed understanding of packet
   reception timing, possible reordering, and losses, as this
   information is used to ensure smooth media play-out, and is reported
   in the RTCP feedback statistics.

4.  RTP-to-QUIC Mapping

   This section address the necessary considerations to realize _one_
   possible way of carrying RTP-over-QUIC.

   Editor's note: At this point, this section is intended to explore the
   design space and briefly describe a number of different options
   without making specific recommendations about which option(s) to
   choose.  Future revisions of this document move towards taking
   concrete decisions.

Ott, et al.               Expires March 5, 2018                 [Page 5]

Internet-Draft                RTP over QUIC               September 2017

4.1.  Mapping Semantic Units

   RTP payload formats define a mapping of media data units (e.g., video
   or audio frames, audio samples, etc.) to packets.  Assuming that we
   will preserve the structure of RTP header, optional header extension,
   and payload, there are two obvious options:

   o  Preserve the previous RTP assumptions about semantic fragmentation
      at MTU size boundaries; i.e., use the same packetization mechanism
      as before, just then drop the resulting RTP packet into a QUIC
      payload.  Note that the MTU size may be smaller since QUIC packet
      headers are larger than plain UDP headers.  This approach is most
      effective if the QUIC implementation allows the application to
      provide hints on where to fragment the QUIC stream into UDP
      packets at the sender side.
   o  Operate solely on semantic units such as video frames, and map
      each semantic unit to a QUIC payload.  This approach leaves the
      final packetization decision to QUIC.  In this case, our "MTU
      size" would not be defined by the IP layer but by QUIC.  It is
      possible in this case for video frame composed of multiple RTP
      packets to use one RTP header for the whole video frame; no need
      to break the video frame to multiple RTP packet, put all payload
      as one RTP packet whose size may be bigger than MTU and send it as
      QUIC payload.

   If we assume that semantic units are to be received and processed
   (and released to the application) atomically for best performance
   results, then option 2) would be preferred.  If we consider that
   subunits are meaningful (e.g., slices in case of video), then option
   1) may be preferred.  This is heavily dependent on how tightly
   coupled are the application, RTP stack, and QUIC transport, and on
   what visibility and control is provided into the QUIC stream
   fragmentation, reception, and reception timing.  In any case,
   however, it would be up to the payload definition to determine what a
   semantic unit.

4.2.  Encapsulating Media Units

   QUIC streams do not preserve packet boundaries, but rather offer a
   stream abstraction similar to that of TCP.  Therefore, if multiple
   identifiable media units are to be transmitted on the same stream,
   the encapsulation mechanisms MUST provide boundaries for media data
   units, e.g., similar to the approach chosen for carrying RTP in TCP.

   [Editor's note: QUIC requires a stream abstraction on the wire, but
   does it require the API offered to the application to provide a
   stream abstraction?  Could a QUIC implementation that's tightly

Ott, et al.               Expires March 5, 2018                 [Page 6]

Internet-Draft                RTP over QUIC               September 2017

   integrated into the application provide more control without
   violating the on-the-wire protocol?]

   The exception would be if only a single frame is ever transmitted
   across a single stream (see option 3 in section 3.3) so that stream
   termination signifies the end of the respective packet.

4.3.  Mapping Media to Streams

   There are (at least) three basic distinct options for mapping media
   to streams:

   o  Map an RTP session to a QUIC stream.  In this case, all media
      packets of the RTP session would be carried within a single QUIC
   o  Map an RTP stream to a QUIC stream.  In case, as presently
      discussed in the QUIC WG, the QUIC stream would be unidirectional
      and we will have one QUIC stream per transmission direction.

   Note that both options would map, e.g., FEC or retransmission
   sessions to different QUIC streams.  Note also that both 1 and 2
   implicitly create the problem of head-of-line blocking since QUIC
   streams are reliable and order preserving.  This would thus not serve
   the real-time nature of RTP packets well.  [Editor's note: to what
   extent are reliability and ordered required in the QUIC API?
   Provided the retransmission is made on the wire, is there anything
   stopping a QUIC implementation releasing data to the application out-

   o  Map each independently decodable groups of frames, video frame, or
      even packet, depending on the encapsulation chosen to an
      individual QUIC stream.  This is independent of whether streams,
      would be uni- or bi-directional.

   Option 3 eliminates the head of line blocking problem of options 1.
   and 2.  because QUIC does not provide any ordering across different
   streams.  Using larger semantic units (e.g., GOPs) for stream
   mapping, would provide for more efficient stream number usage.
   However, all stream frames are still transmitted reliably.  This
   implies that QUIC will perform retransmissions even for packets that
   would be too late already.

   Mapping each video frame or packet to a different stream would raise
   an issue with stream numbering unless all RTP sessions are
   multiplexed on a single UDP socket anyway and then all RTP packets
   would simply be mapped to different streams.

Ott, et al.               Expires March 5, 2018                 [Page 7]

Internet-Draft                RTP over QUIC               September 2017

   An open question here would be how to deal with additional data
   channels that don't use RTP.  Ideally, it should be possible that
   those be within the same QUIC connection (if QUIC is used as
   transport) to avoid consuming again more port numbers.  Since, on the
   one hand, data channels can be set up and torn down at any time and,
   on the other hand, media packets are transmitted continuously, a need
   arises to set aside streams for data channels.  One option would be
   "reserving" those streams in some form.  But then, how many to
   reserve?  Moreover, this would be incompatible with the slides stream
   number window being used by QUIC.  Alternatively, one would need to
   synchronize the use of QUIC streams in real-time between the
   signaling and application channels and the media packet transmission.
   This may be hard to achieve and also suffers from the problem of the
   stream id window moving fast with frame transmissions.  A third
   option would be adding another demultiplexing structure (e.g., to
   different RTP headers from data packets) and use a similar scheme of
   one application data unit (ADU) per stream for other applications.
   While feasible, this appears somewhat cumbersome in the mapping.

   We finally need to consider inter RTP stream synchronisation and how/
   if this would be affected by use of multiple QUIC streams.

   None of the above schemes appear truly satisfactory from a system
   design perspective.  This may call for some refined design
   considerations for QUIC, which we will begin discussing in section 4.

4.4.  Mapping RTCP packets

   RTCP is a bi-directional stream unlike RTP streams which are
   unidirectional.  There can be for example a video stream receiver
   that only receives video content but will send and receive RTCP

   The current discussion on uni-directional streams direction will
   allow both uni- and bi-directional QUIC streams in the same QUIC
   connection.  Such a solution will allow multiplexing of RTP and RTCP
   streams in the same QUIC connection.

   An issue to consider is the encryption of RTCP messages.  The RTP
   secure profiles RTP/SAVP [RFC3711] and RTP/SAVPF [RFC5124] allow NULL
   cipher for RTCP with message integrity.  Using a NULL cipher allow
   RTP middleboxes to monitor the RTP delivery quality (the QUIC
   connection is encrypted as normal, this relates to whether the data
   within the QUIC connection is itself encrypted; c.f. the PERC working

   Whether to use a single stream for forward RTCP and another for
   reverse could be a function of the streams being uni- or

Ott, et al.               Expires March 5, 2018                 [Page 8]

Internet-Draft                RTP over QUIC               September 2017

   bidirectional in the end.  Another question to answer is if there
   should be one stream per SSRC per direction for RTCP.  Finally, RTCP
   packets may also be lost and they contain timing information.
   Avoiding HoL blocking may thus also be important.

4.5.  Mapping of RTP header extensions

   QUIC provides a reliable protocol which addresses the requirement in
   [I-D.ietf-avtcore-rfc5285-bis] to transmit the RTP header extension
   in a couple of RTP packets to provide better reliability.  Still if
   we will adopt mapping option 3 each RTP packet or media frame will
   use a separate QUIC stream.  If a packet with RTP header extension is
   blocked the consecutive RTP packet will continue to arrive; in this
   case it will be beneficial to transmit the RTP header extensions more
   than once to allow for its arrival by the receiver.  Using QUIC as a
   transport for RTP will have all RTP header extensions encrypted
   allowing only entities that terminate a QUIC connection to decode
   them.  RTP header extension as defined in
   [I-D.ietf-avtcore-rfc5285-bis] can be sent in the clear and provide
   information to RTP middleboxes enabling them to route encrypted RTP
   packets.  Currently the following header extensions are used for
   routing of encrypted RTP streams.  Client to mixer audio level
   [RFC6464].  Frame marking [I-D.ietf-avtext-framemarking] and splicing
   interval [I-D.ietf-avtext-splicing-notification].

   Editor's note: need to be clearer about the role of RTP middleboxes
   as specified in RTP topologies [RFC7667]  connected by QUIC
   connections, and what is encrypted/authenticated end-to-end across
   the mesh of QUIC connections in that topology, and what is only
   protected hop-by-hop by QUIC.

5.  Design considerations for QUIC

   This section will address design implications for QUIC and the
   interaction with QUIC of both RTP and RTCP.  In this version, this
   section is still very rudimentary and only identifies some of the
   aspects we expect to discuss in the future:

5.1.  Reliability (or restransmission) control for stream frames

   RTP packets are usually transmitted over unreliable UDP transport,
   with RTP being in full control of timing and, as applicable, of error
   resilience mechanisms.

   QUIC supports only full reliability at this point and would
   retransmit lost packets even if they are no longer needed.  While
   using indepdent streams for different media units could prevent head-
   of-line blocking, retrasmissions would appear to still happen.  To

Ott, et al.               Expires March 5, 2018                 [Page 9]

Internet-Draft                RTP over QUIC               September 2017

   deal with this "issue", it may be worthwhile considering ways to
   control (re)transmission in a fine-grained fashion, e.g., by means of
   supporting partial realibility or by providing access to QUIC buffers
   for (re)transmission control.

5.2.  Congestion control adaptation

   QUIC defines a congestion control mechanism the feasibility of which
   for real-time media streams is yet to be understood.  Media codecs
   have their own constraints for adapting the media transmission rate
   (in terms of reactivity and granularity) and the RMCAT working group
   is currently considering a number of options for real-time media
   congestion control (e.g., [I-D.ietf-rmcat-scream-cc]
   [I-D.ietf-rmcat-gcc] [I-D.ietf-rmcat-nada]
   [I-D.ietf-rmcat-coupled-cc] [I-D.singh-rmcat-adaptive-fec]), in
   addition to the basic circuit breaker mechanism [RFC8083]).  It is an
   open question the extent to which these congestion control
   algorithms, or approaches inspired by them, ought to be incorporated
   into QUIC.

5.3.  RTCP mapping

   RTCP provides feed forward and feedback about the media channel, with
   extensions supporting very detailed per packet reporting.  The
   reception statistics partly overlap with what QUIC ACKs provide
   (especially ACK/NACK ranges and per-packet timestamps).  RTCP
   algorithms could benefit from obtaining access to these statistics
   via a local API to avoid redundancy.

   RTCP packets must also be mapped to QUIC frames (and streams).  Since
   RTP and RTCP can be multiplexed on the same transport address, as
   long as payload boundaries are preserved, RTCP packets could go onto
   any stream.  However, since RTCP packets are used for RTT
   measurements, they should be transmitted independent of the RTP
   packets and ideally without blocking, so that head-of-line blocking
   by other packets should be avoided.  If RTT measurements can be
   imported from QUIC (see above), exact timing control of RTCP packets
   won't be necessary; yet RTCP packets contain other information that
   require timely delivery.  Similar to RTP, RTCP does not require
   reliable delivery.

5.4.  API

   We will need to understand how (if at all) a QUIC API could (and if
   it should) provide the necessary support for RTP/RTCP transmission
   and reception.  This could include transmission timing control;
   providing transmission and reception timestamps; supporting
   retransmission control and/or buffer managements, among others.  The

Ott, et al.               Expires March 5, 2018                [Page 10]

Internet-Draft                RTP over QUIC               September 2017

   extent to which the principle of application level framing [ALF]
   should be incorporated into QUIC implementations, and how tightly
   coupled those implementations can be to the RTP stack and
   application, is unclear.  How example, can a QUIC implementation
   deliver data out-of-order or allow control over stream fragmentation,
   both of which would improve performance for real-time media over RTP,
   provided it keeps the wire format unchanged?  The service model needs
   to become clearer.

5.5.  Multiparty

   RTP is explicitly a group communication protocol, even when unicast.
   If we assume multicast QUIC is undesirable, there needs to be a
   scoping discussion around topologies.

   Usual web-based conferencing services use one or more central
   system(s) for mixing or forwarding.  Whenever the media streams do
   not require processing at such an entity but are merely forwarded,
   SRTP can provide the necessary end-to-end encryption.  In contrast,
   QUIC "just" provides a secure channel between the endpoints and the
   central entities.  To this end, SRTP could be applied inside QUIC for
   certain scenarios.

6.  SDP Extensions for Negotiating RTP-over-QUIC


7.  Security Considerations

   RTP is used as a plain payload for QUIC, exploiting its multiplexing
   capabilities.  To this end, the RTP packets are protected
   (confidentiality) by the QUIC security mechanisms.  Hence, the
   security considerations pertinent to QUIC apply.

   QUIC is by its very nature a transport layer security mechanisms.
   RTP traffic will thus be protected on a single transport hop only.
   As soon RTP topologies more complex than a point-to-point connection
   are used (e.g., [RFC7667]), RTP traffic will lose its end-to-end
   protection as transport connections are terminated at the
   intermediary, even if this acts just as a relay.

8.  IANA Considerations

   There are no IANA considerations at this point.

Ott, et al.               Expires March 5, 2018                [Page 11]

Internet-Draft                RTP over QUIC               September 2017

9.  Acknowledgments

10.  References

10.1.  Normative References

              Iyengar, J. and I. Swett, "QUIC Loss Detection and
              Congestion Control", draft-ietf-quic-recovery-05 (work in
              progress), August 2017.

              Thomson, M. and S. Turner, "Using Transport Layer Security
              (TLS) to Secure QUIC", draft-ietf-quic-tls-05 (work in
              progress), August 2017.

              Iyengar, J. and M. Thomson, "QUIC: A UDP-Based Multiplexed
              and Secure Transport", draft-ietf-quic-transport-05 (work
              in progress), August 2017.

   [RFC3550]  Schulzrinne, H., Casner, S., Frederick, R., and V.
              Jacobson, "RTP: A Transport Protocol for Real-Time
              Applications", STD 64, RFC 3550, DOI 10.17487/RFC3550,
              July 2003, <>.

10.2.  Informative References

   [ALF]      Clark, D. and D. Tennenhouse, "Architectural
              Considerations for a New Generation of Network Protocols",
              Proceedings of ACM SIGCOMM, 1990.

              Brosh, E., Baset, S., Rubinstein, D., and H. Schulzrinne,
              "The Delay-Friendliness of TCP", Proceedings of ACM
              SIGMETRICS, 2008.

              Singer, D., Desineni, H., and R. Even, "A General
              Mechanism for RTP Header Extensions", draft-ietf-avtcore-
              rfc5285-bis-14 (work in progress), August 2017.

              Berger, E., Nandakumar, S., and M. Zanaty, "Frame Marking
              RTP Header Extension", draft-ietf-avtext-framemarking-05
              (work in progress), July 2017.

Ott, et al.               Expires March 5, 2018                [Page 12]

Internet-Draft                RTP over QUIC               September 2017

              Xia, J., Even, R., Huang, R., and D. Lingli, "RTP/RTCP
              extension for RTP Splicing Notification", draft-ietf-
              avtext-splicing-notification-09 (work in progress), August

              Holmberg, C., Alvestrand, H., and C. Jennings,
              "Negotiating Media Multiplexing Using the Session
              Description Protocol (SDP)", draft-ietf-mmusic-sdp-bundle-
              negotiation-38 (work in progress), April 2017.

              Kuehlewind, M. and B. Trammell, "Applicability of the QUIC
              Transport Protocol", draft-ietf-quic-applicability-00
              (work in progress), July 2017.

              Bishop, M., "Hypertext Transfer Protocol (HTTP) over
              QUIC", draft-ietf-quic-http-05 (work in progress), August

              Kuehlewind, M., Trammell, B., and D. Druta, "Manageability
              of the QUIC Transport Protocol", draft-ietf-quic-
              manageability-00 (work in progress), July 2017.

              Islam, S., Welzl, M., and S. Gjessing, "Coupled congestion
              control for RTP media", draft-ietf-rmcat-coupled-cc-06
              (work in progress), March 2017.

              Holmer, S., Lundin, H., Carlucci, G., Cicco, L., and S.
              Mascolo, "A Google Congestion Control Algorithm for Real-
              Time Communication", draft-ietf-rmcat-gcc-02 (work in
              progress), July 2016.

              Zhu, X., Pan, R., Ramalho, M., Cruz, S., Jones, P., Fu,
              J., and S. D'Aronco, "NADA: A Unified Congestion Control
              Scheme for Real-Time Media", draft-ietf-rmcat-nada-04
              (work in progress), March 2017.

              Johansson, I. and Z. Sarker, "Self-Clocked Rate Adaptation
              for Multimedia", draft-ietf-rmcat-scream-cc-10 (work in
              progress), July 2017.

Ott, et al.               Expires March 5, 2018                [Page 13]

Internet-Draft                RTP over QUIC               September 2017

              Alvestrand, H., "Overview: Real Time Protocols for
              Browser-based Applications", draft-ietf-rtcweb-overview-18
              (work in progress), March 2017.

              Perkins, C., Westerlund, M., and J. Ott, "Web Real-Time
              Communication (WebRTC): Media Transport and Use of RTP",
              draft-ietf-rtcweb-rtp-usage-26 (work in progress), March

              Singh, V., Nagy, M., Ott, J., and L. Eggert, "Congestion
              Control Using FEC for Conversational Media", draft-singh-
              rmcat-adaptive-fec-03 (work in progress), March 2016.

   [RFC2736]  Handley, M. and C. Perkins, "Guidelines for Writers of RTP
              Payload Format Specifications", BCP 36, RFC 2736,
              DOI 10.17487/RFC2736, December 1999, <https://www.rfc-

   [RFC3261]  Rosenberg, J., Schulzrinne, H., Camarillo, G., Johnston,
              A., Peterson, J., Sparks, R., Handley, M., and E.
              Schooler, "SIP: Session Initiation Protocol", RFC 3261,
              DOI 10.17487/RFC3261, June 2002, <https://www.rfc-

   [RFC3711]  Baugher, M., McGrew, D., Naslund, M., Carrara, E., and K.
              Norrman, "The Secure Real-time Transport Protocol (SRTP)",
              RFC 3711, DOI 10.17487/RFC3711, March 2004,

   [RFC4571]  Lazzaro, J., "Framing Real-time Transport Protocol (RTP)
              and RTP Control Protocol (RTCP) Packets over Connection-
              Oriented Transport", RFC 4571, DOI 10.17487/RFC4571, July
              2006, <>.

   [RFC5124]  Ott, J. and E. Carrara, "Extended Secure RTP Profile for
              Real-time Transport Control Protocol (RTCP)-Based Feedback
              (RTP/SAVPF)", RFC 5124, DOI 10.17487/RFC5124, February
              2008, <>.

   [RFC5761]  Perkins, C. and M. Westerlund, "Multiplexing RTP Data and
              Control Packets on a Single Port", RFC 5761,
              DOI 10.17487/RFC5761, April 2010, <https://www.rfc-

Ott, et al.               Expires March 5, 2018                [Page 14]

Internet-Draft                RTP over QUIC               September 2017

   [RFC5762]  Perkins, C., "RTP and the Datagram Congestion Control
              Protocol (DCCP)", RFC 5762, DOI 10.17487/RFC5762, April
              2010, <>.

   [RFC5763]  Fischl, J., Tschofenig, H., and E. Rescorla, "Framework
              for Establishing a Secure Real-time Transport Protocol
              (SRTP) Security Context Using Datagram Transport Layer
              Security (DTLS)", RFC 5763, DOI 10.17487/RFC5763, May
              2010, <>.

   [RFC5764]  McGrew, D. and E. Rescorla, "Datagram Transport Layer
              Security (DTLS) Extension to Establish Keys for the Secure
              Real-time Transport Protocol (SRTP)", RFC 5764,
              DOI 10.17487/RFC5764, May 2010, <https://www.rfc-

   [RFC6464]  Lennox, J., Ed., Ivov, E., and E. Marocco, "A Real-time
              Transport Protocol (RTP) Header Extension for Client-to-
              Mixer Audio Level Indication", RFC 6464,
              DOI 10.17487/RFC6464, December 2011, <https://www.rfc-

   [RFC7667]  Westerlund, M. and S. Wenger, "RTP Topologies", RFC 7667,
              DOI 10.17487/RFC7667, November 2015, <https://www.rfc-

   [RFC7826]  Schulzrinne, H., Rao, A., Lanphier, R., Westerlund, M.,
              and M. Stiemerling, Ed., "Real-Time Streaming Protocol
              Version 2.0", RFC 7826, DOI 10.17487/RFC7826, December
              2016, <>.

   [RFC8083]  Perkins, C. and V. Singh, "Multimedia Congestion Control:
              Circuit Breakers for Unicast RTP Sessions", RFC 8083,
              DOI 10.17487/RFC8083, March 2017, <https://www.rfc-

Authors' Addresses

   Joerg Ott
   Technische Universitaet Muenchen
   Boltzmannstrasse 3
   Garching bei Muenchen


Ott, et al.               Expires March 5, 2018                [Page 15]

Internet-Draft                RTP over QUIC               September 2017

   Roni Even


   Colin Perkins
   University of Glasgow
   School of Computing Science
   Glasgow  G12 8QQ


   Varun Singh
   Annankatu 31-33 C 42
   Helsinki  00100


Ott, et al.               Expires March 5, 2018                [Page 16]