Networking Working Group N. Shen, Ed.
Internet-Draft E. Chen
Intended status: Standards Track A. Lindem
Expires: October 27, 2017 Cisco Systems
April 25, 2017
Carrying Geo Coordinates Information In IS-IS
draft-shen-isis-geo-coordinates-03
Abstract
This document defines a new IS-IS TLV which carries the Geo
Coordinates information of the system. The Geo Coordinates
information can be used by IS-IS routing or by any applications.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on October 27, 2017.
Copyright Notice
Copyright (c) 2017 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Shen, et al. Expires October 27, 2017 [Page 1]
Internet-Draft IS-IS Geo Location April 2017
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
1.1. Requirements Language . . . . . . . . . . . . . . . . . . 3
2. Packet Encoding . . . . . . . . . . . . . . . . . . . . . . . 3
3. Operations . . . . . . . . . . . . . . . . . . . . . . . . . 5
4. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 5
5. Security Considerations . . . . . . . . . . . . . . . . . . . 5
6. Privacy Considerations . . . . . . . . . . . . . . . . . . . 6
7. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 6
8. Document Change Log . . . . . . . . . . . . . . . . . . . . . 6
8.1. Changes to draft-shen-isis-geo-coordinates-03.txt . . . . 6
8.2. Changes to draft-shen-isis-geo-coordinates-02.txt . . . . 6
8.3. Changes to draft-shen-isis-geo-coordinates-01.txt . . . . 7
8.4. Changes to draft-shen-isis-geo-coordinates-00.txt . . . . 7
9. References . . . . . . . . . . . . . . . . . . . . . . . . . 7
9.1. Normative References . . . . . . . . . . . . . . . . . . 7
9.2. Informative References . . . . . . . . . . . . . . . . . 8
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 8
1. Introduction
The IS-IS routing protocol defined by [ISO10589] has been widely
deployed in various networks. The Geo Coordinates information can be
useful, particularly within the wide area networks for numerous
applications. Similar to the Dynamic Hostname defined in [RFC5301],
the Geo Coordinates can also be used for network management purposes.
In the case of BGP speakers setting the outbound "MED" value in route
advertisement to neighbors, a local policy can be defined to evaluate
the physical location or physical region of the BGP nexthops.
In the case of IGP point-to-multiple operations
[I-D.lamparter-isis-p2mp], [RFC6845], the local system configuration
can be greatly simplified if the outbound metric to remote neighbors
can be generated automatically based on this Geo Location of the IGP
neighbors.
In the application where IS-IS neighbors are on the same "sub-net"
but over the WAN network, this Geo Location information may be used
for equal-cost or unequal-cost load sharing on the local system.
This enables location based operation on anycast IP prefixes and DMZ
gateways across the WAN environment.
For the traffic matrix using the Geo Coordinates within the routing
domain, instead of a collection of IP nexthops which might be
translated into locations, this enables automatic region to region
traffic pattern aggregation.
Shen, et al. Expires October 27, 2017 [Page 2]
Internet-Draft IS-IS Geo Location April 2017
This document describes the IS-IS protocol carrying the Geo
Coordinates information in a new TLV. This TLV can be distributed
within the node's LSP or inside the IIH PDU. The exact mechanism
each application uses this information is outside the scope of this
document.
1.1. Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
2. Packet Encoding
This Geo Coordinates extension introduces one TLV for IS-IS LSP PDU
and for Hello (IIH) PDU. The code of the TLV is described in the
IANA Considerations section of the document. The fields specify the
location of the system using WGS-84 (World Geodetic System) reference
coordinate system [WGS84]. The value of the Geo Coordinates TLV
consists of the following fields:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|U|N|E|A|M|R|K| Reserved | Location Uncertainty |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Lat Degrees | Latitude Milliseconds |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Long Degrees | Longitude Milliseconds |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Altitude |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Radius | Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| .. Optional Sub-TLVs
+-+-+-+-+-+-+-+-+-....
Type: TBD. 8 bits value, to be assigned by IANA.
Length: Variable. 8 bits value. The mandatory part is 16 octets.
U-bit: If the U-bit is set, it indicates that the "Location
Uncertainty" field is specified. If the U-bit is clear, it
indicates the "Location Uncertainty" field is unspecified.
N-bit: If the N-bit is set, it indicates the Latitude is north
relative to the Equator. If the N-bit is clear, it
indicates the Latitude is south of the Equator.
Shen, et al. Expires October 27, 2017 [Page 3]
Internet-Draft IS-IS Geo Location April 2017
E-bit: If the E-bit is set, it indicates the Longitude is east of
the Prime Meridian. If the E-bit is clear, it indicates the
Longitude is west of the Prime Meridian.
A-bit: If the A-bit is set, it indicates the "Altitude" field is
specified. If the A-bit is clear, it indicates the
"Altitude" field is unspecified.
M-bit: If the M-bit is set, it indicates the "Altitude" is
specified in meters. If the M-bit is clear, it indicates
the "Altitude" is in centimeters.
R-bit: If the R-bit is set, it indicates the "Radius" field is
specified and the encoding is for a circular area. If the
R-bit is clear, it indicates the "Radius" field is
unspecified and the encoding is for a single point.
K-bit: If the K-bit is set, it indicates the "Radius" is specified
in kilometers. If the K-bit is clear, it indicates the
"Radius" is in meters.
Reserved: These bits are reserved. They SHOULD be set to 0 when
sending protocol packets and MUST be ignored when receiving
protocol packets.
Location Uncertainty: Unsigned 16-bit integer indicating the number
of centimeters of uncertainty for the location.
Latitude Degrees: Unsigned 8-bit integer with a range of 0 - 90
degrees north or south of the Equator (northern or southern
hemisphere, respectively).
Latitude Milliseconds: Unsigned 24-bit integer with a range of 0 -
3,599,999 (i.e., less than 60 minutes).
Longitude Degrees: Unsigned 8-bit integer with a range of 0 - 180
degrees east or west of the Prime Meridian.
Longitude Milliseconds: Unsigned 24-bit integer with a range of 0 -
3,599,999 (i.e., less than 60 minutes).
Altitude: Signed 32-bit integer containing the Height relative to
sea level in centimeters or meters. A negative height
indicates that the location is below sea level.
Radius: Unsigned 16-bit integer containing the radius of a circle
centered at the specified coordinates. The radius is
specified in meters unless the K-bit is specified indicating
Shen, et al. Expires October 27, 2017 [Page 4]
Internet-Draft IS-IS Geo Location April 2017
specification in kilometers. If the radius is specified,
the geo-coordinates specify the entire area of the circle
defined by the radius and center point. While the use cases
herein do not make use of this field, future use cases may.
Optional Sub-TLV: Not defined in this document, for future extension
related to the Geo Coordinates information.
3. Operations
This IS-IS Geo Coordinates TLV can be optionally included in the
node's LSP, and it is recommended to be in the LSP fragment zero.
This TLV can also be optionally included in the IIH PDU. This can be
useful when the application is setting the outbound p2mp circuit
metric based on the neighbor's location. This can also be used in
the Spine-Leaf extension [I-D.shen-isis-spine-leaf-ext] where there
is no LSP being flooded into the leaf nodes.
The Geo location information can be statically provisioned on the
system, or it can be dynamically acquired from the GPS capable device
on the system.
4. IANA Considerations
A new TLV codepoint is defined in this document and needs to be
assigned by IANA from the "IS-IS TLV Codepoints" registry. It is
referred to as the Geo Coordinates TLV. This TLV is only to be
optionally inserted in the LSP PDU and the IIH PDU. This document
does not propose any sub-TLV out of this Geo Coordinates TLV.
Value Name IIH LSP SNP Purge
----- --------------------- --- --- --- -----
TBD Geo Coordinates y y n n
5. Security Considerations
Since the Geo Location coordinates provide the exact location of the
routing devices, disclosure may make the IS-IS devices more
susceptible to physical attacks. In situations where this is a
concern (e.g., in military applications, or the topology of the
network is considered proprietary information), the implementation
MUST allow the Geo Location extension to be removed from the IS-IS
advertisement.
Security concerns for the base IS-IS are addressed in [ISO10589],
[RFC5304], [RFC5310], and [RFC7602].
Shen, et al. Expires October 27, 2017 [Page 5]
Internet-Draft IS-IS Geo Location April 2017
6. Privacy Considerations
If the location of an IS-IS router advertising geo location
coordinates as described herein can be directly correlated to an
individual, individuals, or an organization, the location of that
router should be considered sensitive and IS-IS LSP containing such
geo coordinates should be advertised confidentially as described in
Section 5. Additionally, IS-IS network management facilities may
require added authorization to view the contents of IS-IS LSPs
containing geo-Location TLVs. Refer to [RFC6973] for more
information.
The Uncertainty and Confidence metrics for geo-location information
as described in [RFC7459] are not included in the Geo Coordinates
TLV. In a future document, these may be considered for inclusion
with additional Geo Location Sub-TLVs dependent on both on
requirements and adoption of [RFC7459].
7. Acknowledgments
The encoding of the Geo location is adapted from the "Geo Coordinate
LISP Canonical Address Format" specified in the "LISP Canonical
Address Format (LCAF)". We would like to thank the authors of that
Document and particularly Dino Farinacci for subsequent discussions.
Thanks to Les Ginsberg, Yi Yang, and Joe Hildebrand for commenting
and discussions of Geo Coordinates precision encoding. Thanks to
David Ward for commenting on attack vector in relation to this new
capability of IS-IS.
8. Document Change Log
8.1. Changes to draft-shen-isis-geo-coordinates-03.txt
o The 03 version submitted in April 2017 without content change.
8.2. Changes to draft-shen-isis-geo-coordinates-02.txt
o The 02 version submitted in October 2016.
o Changed the format of Geo Location encoding to have Radius field
and flags to be compatible with LISP [LISP-GEO].
o Added the privacy section.
Shen, et al. Expires October 27, 2017 [Page 6]
Internet-Draft IS-IS Geo Location April 2017
8.3. Changes to draft-shen-isis-geo-coordinates-01.txt
o The 01 version submitted in February 2016.
o Change Geo Location encoding to have better precision and to
include uncertainty information.
o Added the discussion in security section for the awareness of
increased probability in attack vector.
8.4. Changes to draft-shen-isis-geo-coordinates-00.txt
o Initial version of the draft is published in February 2016.
9. References
9.1. Normative References
[I-D.lamparter-isis-p2mp]
Franke, C., Lamparter, D., and C. Hopps, "IS-IS Point-to-
Multipoint operation", draft-lamparter-isis-p2mp-01 (work
in progress), October 2015.
[I-D.shen-isis-spine-leaf-ext]
Shen, N., Ginsberg, L., and S. Thyamagundalu, "IS-IS
Routing for Spine-Leaf Topology", draft-shen-isis-spine-
leaf-ext-03 (work in progress), March 2017.
[ISO10589]
ISO "International Organization for Standardization",
"Intermediate system to Intermediate system intra-domain
routeing information exchange protocol for use in
conjunction with the protocol for providing the
connectionless-mode Network Service (ISO 8473), ISO/IEC
10589:2002, Second Edition.", Nov 2002.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<http://www.rfc-editor.org/info/rfc2119>.
[RFC5301] McPherson, D. and N. Shen, "Dynamic Hostname Exchange
Mechanism for IS-IS", RFC 5301, DOI 10.17487/RFC5301,
October 2008, <http://www.rfc-editor.org/info/rfc5301>.
[RFC5304] Li, T. and R. Atkinson, "IS-IS Cryptographic
Authentication", RFC 5304, DOI 10.17487/RFC5304, October
2008, <http://www.rfc-editor.org/info/rfc5304>.
Shen, et al. Expires October 27, 2017 [Page 7]
Internet-Draft IS-IS Geo Location April 2017
[RFC5310] Bhatia, M., Manral, V., Li, T., Atkinson, R., White, R.,
and M. Fanto, "IS-IS Generic Cryptographic
Authentication", RFC 5310, DOI 10.17487/RFC5310, February
2009, <http://www.rfc-editor.org/info/rfc5310>.
[RFC6845] Sheth, N., Wang, L., and J. Zhang, "OSPF Hybrid Broadcast
and Point-to-Multipoint Interface Type", RFC 6845,
DOI 10.17487/RFC6845, January 2013,
<http://www.rfc-editor.org/info/rfc6845>.
[RFC7602] Chunduri, U., Lu, W., Tian, A., and N. Shen, "IS-IS
Extended Sequence Number TLV", RFC 7602,
DOI 10.17487/RFC7602, July 2015,
<http://www.rfc-editor.org/info/rfc7602>.
9.2. Informative References
[LISP-GEO]
Farinacci, D., "LISP Geo-Coordinate Use-Cases", draft-
farinacci-lisp-geo-02 (work in progress), 2016.
[RFC6973] Cooper, A., Tschofenig, H., Aboba, B., Peterson, J.,
Morris, J., Hansen, M., and R. Smith, "Privacy
Considerations for Internet Protocols", RFC 6973,
DOI 10.17487/RFC6973, July 2013,
<http://www.rfc-editor.org/info/rfc6973>.
[RFC7459] Thomson, M. and J. Winterbottom, "Representation of
Uncertainty and Confidence in the Presence Information
Data Format Location Object (PIDF-LO)", RFC 7459,
DOI 10.17487/RFC7459, February 2015,
<http://www.rfc-editor.org/info/rfc7459>.
[WGS84] National Imagery and Mapping Agency, "Department of
Defense World Geodetic System 1984, Third Edition",
NIMA TR8350.2, January 2000.
Authors' Addresses
Naiming Shen (editor)
Cisco Systems
560 McCarthy Blvd.
Milpitas, CA 95035
US
Email: naiming@cisco.com
Shen, et al. Expires October 27, 2017 [Page 8]
Internet-Draft IS-IS Geo Location April 2017
Enke Chen
Cisco Systems
560 McCarthy Blvd.
Milpitas, CA 95035
US
Email: enkechen@cisco.com
Acee Linden
Cisco Systems
301 Midenhall Way
Cary, NC 27513
US
Email: acee@cisco.com
Shen, et al. Expires October 27, 2017 [Page 9]