Network Working Group F. Templin, Ed.
Internet-Draft Boeing Research & Technology
Intended status: Standards Track A. Whyman
Expires: December 15, 2019 MWA Ltd c/o Inmarsat Global Ltd
June 13, 2019
Transmission of IPv6 Packets over Aeronautical ("aero") Interfaces
draft-templin-atn-aero-interface-02.txt
Abstract
Mobile nodes (e.g., aircraft of various configurations) communicate
with networked correspondents over multiple access network data links
and configure mobile routers to connect their on-board networks.
Mobile nodes configure a virtual interface (termed the "aero
interface") as a thin layer over their underlying data link
interfaces. This document specifies the transmission of IPv6 packets
over aeronautical ("aero") interfaces.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on December 15, 2019.
Copyright Notice
Copyright (c) 2019 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(https://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
Templin & Whyman Expires December 15, 2019 [Page 1]
Internet-Draft IPv6 over AERO Interfaces June 2019
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 3
3. Requirements . . . . . . . . . . . . . . . . . . . . . . . . 4
4. Aeronautical ("aero") Interface Model . . . . . . . . . . . . 4
5. Maximum Transmission Unit . . . . . . . . . . . . . . . . . . 5
6. Frame Format . . . . . . . . . . . . . . . . . . . . . . . . 5
7. Link-Local Addresses . . . . . . . . . . . . . . . . . . . . 6
8. Address Mapping - Unicast . . . . . . . . . . . . . . . . . . 6
9. Address Mapping - Multicast . . . . . . . . . . . . . . . . . 9
10. Mobility Service Discovery . . . . . . . . . . . . . . . . . 9
11. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 11
12. Security Considerations . . . . . . . . . . . . . . . . . . . 11
13. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 12
14. References . . . . . . . . . . . . . . . . . . . . . . . . . 12
14.1. Normative References . . . . . . . . . . . . . . . . . . 12
14.2. Informative References . . . . . . . . . . . . . . . . . 13
Appendix A. Aero Option Extensions for Special-Purpose Links . . 13
Appendix B. Prefix Length Considerations . . . . . . . . . . . . 15
Appendix C. Change Log . . . . . . . . . . . . . . . . . . . . . 15
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 16
1. Introduction
Mobile Nodes (MNs) such as aircraft of various configurations may
have multiple data links for communicating with networked
correspondents. These data links often have differing performance,
cost and availability characteristics that can change dynamically
according to mobility patterns, flight phases, proximity to
infrastructure, etc.
Each MN receives an IPv6 Mobile Network Prefix (MNP) that can be used
by on-board networks regardless of the actual link or links selected
for data transport. The MN performs router discovery the same as for
customer edge routers [RFC7084], and acts as a mobile router on
behalf of its on-board networks. A virtual interface (termed the
"aero interface") is configured as a thin layer over the underlying
access network data link interfaces.
The aero interface is therefore the only interface abstraction
exposed to the IPv6 layer and behaves according to the Non-Broadcast,
Multiple Access (NBMA) interface principle, while underlying access
Templin & Whyman Expires December 15, 2019 [Page 2]
Internet-Draft IPv6 over AERO Interfaces June 2019
network interfaces appear as link layer communication channels in the
architecture.
The aero interface interacts with the ground domain Mobility Service
(MS) through control message exchanges based on IPv6 Nieghbor
Discovery [RFC4861]. The MS tracks MN movements and represents their
MNPs in a global routing or mapping system.
This document specifies the transmission of IPv6 packets [RFC8200]
and MN/MS control messaging over aeronautical ("aero") interfaces.
2. Terminology
The terminology in the normative references applies; especially, the
terms "link" and "interface" are the same as defined in the IPv6
[RFC8200] and IPv6 Neighbor Discovery (ND) [RFC4861] specifications.
The following terms are defined within the scope of this document:
Access Network (ANET)
a data link service network (e.g., an aviation radio access
network, satellite service provider network, cellular operator
network, etc.) protected by physical and/or link layer security.
Each ANET connects to outside Internetworks via border security
devices such as proxys, firewalls, packet filtering gateways, etc.
ANET interface
a node's attachment to a link in an ANET.
Internetwork (INET)
a connected network region with a coherent IP addressing plan that
provides transit forwarding services for ANET mobile nodes and
INET correspondents. Examples include private enterprise
networks, aviation networks and the global public Internet itself.
INET interface
a node's attachment to a link in an INET.
aero link
a virtual overlay configured over one or more INETs and their
connected ANETs. An aero link may comprise multiple segments
joined by bridges the same as for any link; the addressing plans
in each segment may be mutually exclusive and managed by different
administrative entities.
aero interface
a node's attachment to an aero link, and configured over one or
more underlying ANET/INET interfaces.
Templin & Whyman Expires December 15, 2019 [Page 3]
Internet-Draft IPv6 over AERO Interfaces June 2019
aero address
an IPv6 link-local address constructed as specified in Section 7,
and assigned to an aero interface.
3. Requirements
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119]. Lower case
uses of these words are not to be interpreted as carrying RFC2119
significance.
4. Aeronautical ("aero") Interface Model
An aero interface is a Mobile Node (MN) virtual interface configured
over one or more ANET interfaces, which may be physical (e.g., an
aeronautical radio link) or virtual (e.g., an Internet or higher-
layer "tunnel"). The MN coordinates with the aero link Mobility
Service (MS) through Router Solicitation (RS) / Router Advertisement
(RA) message exchanges.
The aero interface architectural layering model is the same as in
[RFC7847], and augmented as shown in Figure 1. The IPv6 layer
therefore sees the aero interface as a single network layer interface
with multiple underlying ANET interfaces that appear as link layer
communication channels in the architecture.
+----------------------------+
| TCP/UDP |
Session-to-IP +---->| |
Address Binding | +----------------------------+
+---->| IPv6 |
IP Address +---->| |
Binding | +----------------------------+
+---->| aero Interface |
Logical-to- +---->| (aero address) |
Physical | +----------------------------+
Interface +---->| L2 | L2 | | L2 |
Binding |(IF#1)|(IF#2)| ..... |(IF#n)|
+------+------+ +------+
| L1 | L1 | | L1 |
| | | | |
+------+------+ +------+
Figure 1: Aero Interface Architectural Layering Model
The aero virtual interface model gives rise to a number of
opportunities:
Templin & Whyman Expires December 15, 2019 [Page 4]
Internet-Draft IPv6 over AERO Interfaces June 2019
o since aero interface link-local addresses are uniquely derived
from an MNP (see: Section 7, no Duplicate Address Detection (DAD)
messaging is necessary over the aero interface.
o ANET interfaces can remain unnumbered in environments where
communications are coordinated entirely over the aero interface.
o as ANET interface properties change (e.g., link quality, cost,
availability, etc.), any active ANET interface can be used to
update the profiles of multiple additional ANET interfaces in a
single RS/RA message exchange. This allows for timely adaptation
and service continuity under dynamically changing conditions.
o coordinating ANET interfaces in this way allows them to be
represented in a unified MS profile with provisions for mobility
and multilink operations.
o exposing a single virtual interface abstraction to the IPv6 layer
allows for traffic engineering (including QoS based link
selection, packet replication, load balancing, etc.) at the link
layer while still permitting queuing at the IPv6 layer based on,
e.g., traffic class, flow label, etc.
Other opportunities are discussed in [RFC7847].
5. Maximum Transmission Unit
The aero interface and all underlying ANET interfaces MUST configure
an MTU of at least 1280 bytes [RFC8200]. The aero interface SHOULD
configure an MTU that is no smaller than the largest MTU among all
ANET interfaces.
The aero interface returns locally-generated ICMPv6 "Packet Too Big"
messages for packets that are too large to traverse the selected
underlying ANET interface. This ensures that the MTU is adaptive and
reflects the ANET interface used for a given data flow.
6. Frame Format
The aero interface transmits IPv6 packets according to the native
frame format of each underlying ANET interface. For example, for an
Ethernet interface the frame format is exactly as specified in
[RFC2464], for tunnels over IPv6 the frame format is exactly as
specified in [RFC2473], etc.
Templin & Whyman Expires December 15, 2019 [Page 5]
Internet-Draft IPv6 over AERO Interfaces June 2019
7. Link-Local Addresses
A MN "aero address" is an IPv6 link-local address with an interface
identifier based on its assigned MNP. MN aero addresses begin with
the prefix fe80::/64 followed by a 64-bit prefix taken from the MNP
(see: Appendix B). For example, for the MNP:
2001:db8:1000:2000::/56
the corresponding aero addresses are:
fe80::2001:db8:1000:2000
fe80::2001:db8:1000:2001
fe80::2001:db8:1000:2002
... etc. ...
fe80::2001:db8:1000:20ff
When the MN configures aero addresses from its MNP, it assigns them
to the aero interface. The lowest-numbered aero address serves as
the "base" address (for example, for the MNP 2001:db8:1000:2000::/56
the base aero address is fe80::2001:db8:1000:2000). The MN uses the
base areo address for IPv6 ND messaging, but accepts packets destined
to all aero addresses equally (i.e., the same as for any multi-
addressed IPv6 interface).
MS aero addresses are allocated from the range fe80::/96, and MUST be
managed for uniqueness by the collective aero link administrative
authorities. Each address represents a distinct service endpoint in
the MS. The lower 32 bits of the address includes a unique integer
value, e.g., fe80::1, fe80::2, fe80::3, etc. The address fe80:: is
reserved as the IPv6 link-local Subnet Router Anycast address
[RFC4291], and the address fe80::ffff:ffff is reserved as the
unspecified aero address; hence, these values are not available for
general assignment.
Since MN aero addresses are guaranteed unique by the nature of the
unique MNP delegation, aero interfaces set the autoconfiguration
variable DupAddrDetectTransmits to 0 [RFC4862].
8. Address Mapping - Unicast
Each aero interface maintains a neighbor cache for tracking per-
neighbor state the same as for any IPv6 interface. The aero
Templin & Whyman Expires December 15, 2019 [Page 6]
Internet-Draft IPv6 over AERO Interfaces June 2019
interface uses standard IPv6 Neighbor Discovery (ND) messaging
[RFC4861].
IPv6 ND messages on aero interfaces use the native Source/Target
Link-Layer Address Option (S/TLLAO) formats of the underlying ANET
interfaces (e.g., for Ethernet the S/TLLAO is specified in
[RFC2464]).
Aero interfaces also use the link-local address format specified in
Section 7, and aero interface IPv6 ND messages include aero options
formatted as shown in Figure 2:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length = 5 | Prefix Length |S|R|D| Reserved|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ifindex | Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ +
| |
+ Mobile Network Prefix (MNP) +
| |
+ +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|P00|P01|P02|P03|P04|P05|P06|P07|P08|P09|P10|P11|P12|P13|P14|P15|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|P16|P17|P18|P19|P20|P21|P22|P23|P24|P25|P26|P27|P28|P29|P30|P31|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|P32|P33|P34|P35|P36|P37|P38|P39|P40|P41|P42|P43|P44|P45|P46|P47|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|P48|P49|P50|P51|P52|P53|P54|P55|P56|P57|P58|P59|P60|P61|P62|P63|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 2: Aero Option Format
In this format:
o Type is set to TBD (to be assigned by IANA).
o Length is set to the constant value '5' (i.e., 5 units of 8
octets).
o Prefix Length is set to the length of the prefix found in the
Mobile Network Prefix (MNP) field. For RS messages, the MS
validates the MNP assertion, then announces the MNP in the routing
Templin & Whyman Expires December 15, 2019 [Page 7]
Internet-Draft IPv6 over AERO Interfaces June 2019
system and returns an RA with Router Lifetime set to the MNP
assertion lifetime.
o S (the 'Source' bit) is set to '1' in the aero options of an ND
message that correspond to the ANET interface over which the ND
message is sent, and set to '0' in all other aero options.
o R (the "Release" bit) is set to '1' in the aero option of an RS
message sent for the purpose of withdrawing from the MS;
otherwise, set to '0'. The MS withdraws the MNP, then returns an
RA with Router Lifetime set to '0'.
o D (the "Disable" bit) is set to '1' in the aero option of an RS
message for each ifIndex that is to be disabled in the recipient's
neighbor cache entry; otherwise, set to '0'. If the message
contains multiple aero options the D value in each option is
consulted.
o Both 'Reserved' fields are set to the value '0' on transmission.
o ifIndex is set to a 16-bit integer value corresponding to a
specific underlying ANET interface as discussed in [RFC2863].
Once the MN has assigned an ifIndex to an ANET interface, the
assignment MUST remain unchanged until the MN disables the
interface. MNs MUST number each ifIndex with a value between '1'
and '0xffff', and RA messages sent by the MS MUST set ifIndex to
0.
o Mobile Network Prefix (MNP) is set to the IPv6 Prefix assigned to
the MN. Prefix Length and MNP in an RS message MUST be values
that the MN is authorized to assert. Otherwise, the MS ignores
the RS message and does not enter the MNP into the routing/mapping
system.
o P(i) is a set of Preferences that correspond to the 64
Differentiated Service Code Point (DSCP) values [RFC2474]. Each
P(i) is set to the value '0' ("disabled"), '1' ("low"), '2'
("medium") or '3' ("high") to indicate a QoS preference level for
ANET interface selection purposes.
MNs such as aircraft typically have many wireless data link types
(e.g. satellite-based, cellular, terrestrial, air-to-air directional,
etc.) with diverse performance, cost and availability properties.
From the perspective of ND, the aero interface would therefore appear
to have multiple link layer addresses. In that case, ND messages MAY
include multiple aero options - each with an ifIndex that corresponds
to a specific ANET interface.
Templin & Whyman Expires December 15, 2019 [Page 8]
Internet-Draft IPv6 over AERO Interfaces June 2019
When an ND message includes aero options, the options corresponding
to the underlying ANET interface used to transmit the message MUST
set S to '1'.
9. Address Mapping - Multicast
The multicast address mapping of the native underlying ANET interface
applies, and the ANET interacts with the MS for multicast forwarding
and group management purposes.
The mobile router on board the aircraft also serves as an IGMP/MLD
Proxy for its EUNs and/or hosted applications per [RFC4605] while
using the link layer address of the router as the link layer address
for all multicast packets.
10. Mobility Service Discovery
MNs interact with the MS through mobility extensions on first-hop
ANET Access Routers (ARs). MS extensions on ARs MUST examine the RS
messages received on an ANET interface. If the RS message includes
aero options, the MS is invoked and an appropriate RA message is
generated the same as for an IPv6 router. If the RS message does not
include aero options, the AR instead processes the RS message locally
the same as for an ordinary IPv6 link.
MNs configure aero interfaces that observe the properties discussed
in the previous section. The aero interface and its underlying
interfaces are said to be in either the "UP" or "DOWN" state
according to administrative actions in conjunction with the interface
connectivity status. An aero interface transitions to UP or DOWN
through administrative action and/or through state transitions of the
underlying interfaces. When a first underlying interface transitions
to UP, the aero interface also transitions to UP. When all
underlying interfaces transition to DOWN, the aero interface also
transitions to DOWN.
MNs coordinate with the MS through RS/RA exchanges via their aero
interfaces. When an aero interface transitions to UP, the MN sends
initial RS messages with aero options to assert its MNP and register
an initial set of underlying ANET interfaces that are also UP. The
MN sends additional RS messages to refresh MNP and/or router
lifetimes, and to register/deregister underlying ANET interfaces as
they transition to UP or DOWN.
The MS sends RA messages with configuration information in response
to a MN's RS message. The MS sends immediate unicast RA responses
without delay; therefore, the 'MAX_RA_DELAY_TIME' and
'MIN_DELAY_BETWEEN_RAS' constants for multicast RAs do not apply.
Templin & Whyman Expires December 15, 2019 [Page 9]
Internet-Draft IPv6 over AERO Interfaces June 2019
The MS MAY send periodic and/or event-driven unsolicited RA messages,
but is not required to do so for unicast advertisements [RFC4861].
The MN sends RS messages from within the aero interface while using
an UP underlying ANET interface as the outbound interface. Each
message is formatted as an ordinary RS message as though it
originated from the IPv6 layer, but the process is coordinated wholly
from within the aero interface and is therefore opaque to the IPv6
layer. The MN sends an initial RS message over an UP underlying
interface with its base aero address as the source address, all-
routers multicast as the destination address and with an aero option
with a valid Prefix Length and MNP. The aero option also sets S to 1
and contains valid ifIndex and P(i) values appropriate for the
underlying ANET interface.
When the MS receives the RS, it accepts the message if the prefix
assertion was acceptable and drops the message silently otherwise.
If the prefix assertion was accepted, the MS injects the MNP into the
routing/mapping system then caches the new ifIndex, Prefix Length,
MNP and P(i) values. The MS then returns an RA with the aero address
of a MS endpoint as the source address, the aero address of the MN as
the destination address and with Router Lifetime set to a non-zero
value.
After the MN receives the initial RA confirming the MNP assertion, it
notes the aero address in the RA as the destination for all
subsequent RS messages it sends via this MS endpoint. If the MN
needs to change to a different MS endpoint, it discovers and uses a
different MS aero address.
The MN then manages its underlying ANET interfaces according to their
states as follows:
o When an underlying ANET interface transitions to UP, the MN sends
an RS over the ANET interface with its base aero address as the
source address, the MS aero address as the destination address,
and with one or more aero options. Aero options corresponding to
the ANET interface set S to 1 and contain valid ifIndex and P(i)
values appropriate for this ANET interface, while any additional
aero options set S to 0 and contain valid ifIndex and P(i) values
appropriate for other ANET interfaces.
o When an underlying ANET interface transitions to DOWN, the MN
sends an RS over any UP ANET interface with an aero option for the
DOWN ANET interface with D set to 1. The RS may include
additional aero options for additional ANET interfaces as above.
Templin & Whyman Expires December 15, 2019 [Page 10]
Internet-Draft IPv6 over AERO Interfaces June 2019
o When a MN wishes to relase from the current MS endpoint, it sends
an RS message over any UP ANET interface with an aero option with
R set to 1. When the MS receives the RS message, it withdraws the
MNP from the routing/mapping system and returns an RA message with
Router Lifetime set to 0.
o When all of a MNs underlying interfaces have transitioned to DOWN,
the MS withdraws the MNP the same as if it had received an RS with
an aero option with R set to 1.
The MN is responsible for retrying each RS/RA exchange up to
MAX_RTR_SOLICITATIONS times separated by RTR_SOLICITATION_INTERVAL
seconds until an RA is received. If no RA is received over multiple
UP ANET interfaces, the MN declares this MS endpoint unreachable and
tries a different MS endpoint.
The IPv6 layer sees the aero interface as an ordinary IPv6 interface.
Therefore, when the IPv6 layer sends an RS message the aero interface
returns an internally-generated RA message as though the message
originated from an IPv6 router. The internally-generated RA message
contains configuration information (such as Router Lifetime, MTU,
etc.) that is consistent with the information received from the RAs
generated by the MS.
Whether the aero interface RS/RA process is initiated from the
receipt of an RS message from the IPv6 layer is an implementation
matter. Some implementations may elect to defer the RS/RA process
until an RS is received from the IPv6 layer, while others may elect
to initiate the RS/RA process independently of any IPv6 layer
messaging.
11. IANA Considerations
The IANA is instructed to allocate an IPv6 Neighbor Discovery option
type for the aero option in the IPv6 Neighbor Discovery Option
Formats registry.
12. Security Considerations
Security considerations are the same as defined for the specific
access network interface types, and readers are referred to the
appropriate interface specifications.
IPv6 and IPv6 ND security considerations also apply, and are
specified in the normative references.
Templin & Whyman Expires December 15, 2019 [Page 11]
Internet-Draft IPv6 over AERO Interfaces June 2019
13. Acknowledgements
This document was prepared per the consensus decision at the 8th
Conference of the International Civil Aviation Organization (ICAO)
Working Group-I Mobility Subgroup on March 22, 2019. Attendees and
contributors included: Guray Acar, Danny Bharj, Francois D'Humieres,
Pavel Drasil, Nikos Fistas, Giovanni Garofolo, Vaughn Maiolla, Tom
McParland, Victor Moreno, Madhu Niraula, Brent Phillips, Liviu
Popescu, Jacky Pouzet, Aloke Roy, Greg Saccone, Robert Segers,
Stephane Tamalet, Fred Templin, Bela Varkonyi, Tony Whyman, and
Dongsong Zeng.
The following individuals are acknowledged for their useful comments:
Pavel Drasil, Zdenek Jaron.
.
14. References
14.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/info/rfc2119>.
[RFC2474] Nichols, K., Blake, S., Baker, F., and D. Black,
"Definition of the Differentiated Services Field (DS
Field) in the IPv4 and IPv6 Headers", RFC 2474,
DOI 10.17487/RFC2474, December 1998,
<https://www.rfc-editor.org/info/rfc2474>.
[RFC4291] Hinden, R. and S. Deering, "IP Version 6 Addressing
Architecture", RFC 4291, DOI 10.17487/RFC4291, February
2006, <https://www.rfc-editor.org/info/rfc4291>.
[RFC4861] Narten, T., Nordmark, E., Simpson, W., and H. Soliman,
"Neighbor Discovery for IP version 6 (IPv6)", RFC 4861,
DOI 10.17487/RFC4861, September 2007,
<https://www.rfc-editor.org/info/rfc4861>.
[RFC4862] Thomson, S., Narten, T., and T. Jinmei, "IPv6 Stateless
Address Autoconfiguration", RFC 4862,
DOI 10.17487/RFC4862, September 2007,
<https://www.rfc-editor.org/info/rfc4862>.
Templin & Whyman Expires December 15, 2019 [Page 12]
Internet-Draft IPv6 over AERO Interfaces June 2019
[RFC8200] Deering, S. and R. Hinden, "Internet Protocol, Version 6
(IPv6) Specification", STD 86, RFC 8200,
DOI 10.17487/RFC8200, July 2017,
<https://www.rfc-editor.org/info/rfc8200>.
14.2. Informative References
[RFC2464] Crawford, M., "Transmission of IPv6 Packets over Ethernet
Networks", RFC 2464, DOI 10.17487/RFC2464, December 1998,
<https://www.rfc-editor.org/info/rfc2464>.
[RFC2473] Conta, A. and S. Deering, "Generic Packet Tunneling in
IPv6 Specification", RFC 2473, DOI 10.17487/RFC2473,
December 1998, <https://www.rfc-editor.org/info/rfc2473>.
[RFC2863] McCloghrie, K. and F. Kastenholz, "The Interfaces Group
MIB", RFC 2863, DOI 10.17487/RFC2863, June 2000,
<https://www.rfc-editor.org/info/rfc2863>.
[RFC4605] Fenner, B., He, H., Haberman, B., and H. Sandick,
"Internet Group Management Protocol (IGMP) / Multicast
Listener Discovery (MLD)-Based Multicast Forwarding
("IGMP/MLD Proxying")", RFC 4605, DOI 10.17487/RFC4605,
August 2006, <https://www.rfc-editor.org/info/rfc4605>.
[RFC7084] Singh, H., Beebee, W., Donley, C., and B. Stark, "Basic
Requirements for IPv6 Customer Edge Routers", RFC 7084,
DOI 10.17487/RFC7084, November 2013,
<https://www.rfc-editor.org/info/rfc7084>.
[RFC7421] Carpenter, B., Ed., Chown, T., Gont, F., Jiang, S.,
Petrescu, A., and A. Yourtchenko, "Analysis of the 64-bit
Boundary in IPv6 Addressing", RFC 7421,
DOI 10.17487/RFC7421, January 2015,
<https://www.rfc-editor.org/info/rfc7421>.
[RFC7847] Melia, T., Ed. and S. Gundavelli, Ed., "Logical-Interface
Support for IP Hosts with Multi-Access Support", RFC 7847,
DOI 10.17487/RFC7847, May 2016,
<https://www.rfc-editor.org/info/rfc7847>.
Appendix A. Aero Option Extensions for Special-Purpose Links
The aero option format specified in Section 8 includes a Length value
of 5 (i.e., 5 units of 8 octets). However, special-purpose aero
links may extend the basic format to include additional fields and a
Length value larger than 5.
Templin & Whyman Expires December 15, 2019 [Page 13]
Internet-Draft IPv6 over AERO Interfaces June 2019
For example, adaptation of the aero interface to the Aeronautical
Telecommunications Network with Internet Protocol Services (ATN/IPS)
includes link selection preferences based on transport port numbers
in addition to the existing DSCP-based preferences. ATN/IPS nodes
maintain a map of transport port numbers to 64 possible preference
fields, e.g., TCP port 22 maps to preference field 8, TCP port 443
maps to preference field 20, UDP port 8060 maps to preference field
34, etc. The extended aero option format for ATN/IPS is shown in
Figure 3, where the Length value is 7 and the 'Q(i)' fields provide
link preferences for the corresponding transport port number.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length = 5 | Prefix Length |S|R|D| Reserved|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ifIndex | Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ +
| |
+ Mobile Network Prefix (MNP) +
| |
+ +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|P00|P01|P02|P03|P04|P05|P06|P07|P08|P09|P10|P11|P12|P13|P14|P15|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|P16|P17|P18|P19|P20|P21|P22|P23|P24|P25|P26|P27|P28|P29|P30|P31|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|P32|P33|P34|P35|P36|P37|P38|P39|P40|P41|P42|P43|P44|P45|P46|P47|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|P48|P49|P50|P51|P52|P53|P54|P55|P56|P57|P58|P59|P60|P61|P62|P63|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|Q00|Q01|Q02|Q03|Q04|Q05|Q06|Q07|Q08|Q09|Q10|Q11|Q12|Q13|Q14|Q15|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|Q16|Q17|Q18|Q19|Q20|Q21|Q22|Q23|Q24|Q25|Q26|Q27|Q28|Q29|Q30|Q31|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|Q32|Q33|Q34|Q35|Q36|Q37|Q38|Q39|Q40|Q41|Q42|Q43|Q44|Q45|Q46|Q47|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|Q48|Q49|Q50|Q51|Q52|Q53|Q54|Q55|Q56|Q57|Q58|Q59|Q60|Q61|Q62|Q63|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 3: ATN/IPS Extended Aero Option Format
Templin & Whyman Expires December 15, 2019 [Page 14]
Internet-Draft IPv6 over AERO Interfaces June 2019
Appendix B. Prefix Length Considerations
The IPv6 addressing architecture [RFC4291] reserves the prefix ::/8;
this assures that MNPs will not begin with ::32 so that MN and MS
aero addresses cannot overlap. Additionally, this specification
currently observes the 64-bit boundary in IPv6 addresses [RFC7421].
MN aero addresses insert the most-significant 64 MNP bits into the
least-significant 64 bits of the prefix fe80::/64, however [RFC4291]
defines the link-local prefix as fe80::/10 meaning "fe80" followed by
54 unused bits followed by the least-significant 64 bits of the
address. Future versions of this specification may adapt the 54
unused bits for extended coding of MNP prefixes of /65 or longer (up
to /118).
Appendix C. Change Log
<< RFC Editor - remove prior to publication >>
Differences from draft-templin-atn-aero-interface-01 to draft-
templin-atn-aero-interface-02:
o Removed discussion of encapsulation (out of scope)
o Simplified MTU section
o Changed to use a new IPv6 ND option (the "aero option") instead of
S/TLLAO
o Explained the nature of the interaction between the mobility
management service and the air interface
Differences from draft-templin-atn-aero-interface-00 to draft-
templin-atn-aero-interface-01:
o Updates based on list review comments on IETF 'atn' list from
4/29/2019 through 5/7/2019 (issue tracker established)
o added list of opportunties afforded by the single virtual link
model
o added discussion of encapsulation considerations to Section 6
o noted that DupAddrDetectTransmits is set to 0
o removed discussion of IPv6 ND options for prefix assertions. The
aero address already includes the MNP, and there are many good
Templin & Whyman Expires December 15, 2019 [Page 15]
Internet-Draft IPv6 over AERO Interfaces June 2019
reasons for it to continue to do so. Therefore, also including
the MNP in an IPv6 ND option would be redundant.
o Significant re-work of "Router Discovery" section.
o New Appendix B on Prefix Length considerations
First draft version (draft-templin-atn-aero-interface-00):
o Draft based on consensus decision of ICAO Working Group I Mobility
Subgroup March 22, 2019.
Authors' Addresses
Fred L. Templin (editor)
Boeing Research & Technology
P.O. Box 3707
Seattle, WA 98124
USA
Email: fltemplin@acm.org
Tony Whyman
MWA Ltd c/o Inmarsat Global Ltd
99 City Road
London EC1Y 1AX
England
Email: tony.whyman@mccallumwhyman.com
Templin & Whyman Expires December 15, 2019 [Page 16]