BESS Working Group                                               W. Wang
Internet-Draft                                                   A. Wang
Intended status: Standards Track                           China Telecom
Expires: 9 September 2023                                        H. Wang
                                                     Huawei Technologies
                                                            8 March 2023


                    Layer-3 Accessible EVPN Services
                 draft-wang-bess-l3-accessible-evpn-05

Abstract

   This draft describes layer-3 accessible EVPN service interfaces
   according to [RFC7432], and proposes a new solution which can
   simplify the deployment of layer-3 accessible EVPN service.  This
   solution allows each PE in EVPN network to maintain only one IP-VRF.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at https://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on 9 September 2023.

Copyright Notice

   Copyright (c) 2023 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents (https://trustee.ietf.org/
   license-info) in effect on the date of publication of this document.
   Please review these documents carefully, as they describe your rights
   and restrictions with respect to this document.  Code Components
   extracted from this document must include Revised BSD License text as
   described in Section 4.e of the Trust Legal Provisions and are
   provided without warranty as described in the Revised BSD License.



Wang, et al.            Expires 9 September 2023                [Page 1]


Internet-Draft             L3 Accessible EVPN                 March 2023


Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   2
   2.  Conventions used in this document . . . . . . . . . . . . . .   4
   3.  Terminology . . . . . . . . . . . . . . . . . . . . . . . . .   4
   4.  Service Interfaces in layer-3 accessible EVPN . . . . . . . .   4
   5.  Solutions of LSI-aware bundle service interface . . . . . . .   6
   6.  Protocol Extensions . . . . . . . . . . . . . . . . . . . . .   7
     6.1.  Forwarding Plane  . . . . . . . . . . . . . . . . . . . .   7
       6.1.1.  Extensions to VxLAN . . . . . . . . . . . . . . . . .   7
     6.2.  Control Plane . . . . . . . . . . . . . . . . . . . . . .   7
   7.  Modification of MAC/IP address storage mode on PE . . . . . .   8
   8.  Security Considerations . . . . . . . . . . . . . . . . . . .   9
   9.  IANA Considerations . . . . . . . . . . . . . . . . . . . . .   9
   10. Normative References  . . . . . . . . . . . . . . . . . . . .   9
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  10

1.  Introduction

   [RFC7432]defines three service interfaces for layer-2 accessible
   EVPN: VLAN-Based Service Interface, VLAN-Bundle Service Interface and
   VLAN-Aware Bundle Service Interface.  These three types of service
   interfaces can realize the isolation of layer-2 traffic of customers
   in different ways, as shown in Figure 1.

                1:1           1:1
        +------+   +---------+   +------+
        |VID 11+---+  EVI 1  +---+VID 12|
        +------+   +---------+   +------+
        |VID 21+---+  EVI 2  +---+VID 22|
        +------+   +---------+   +------+
        |VID 31+---+  EVI 3  +---+VID 32|
        +------+   +---------+   +------+
        |VID 41+---+  EVI 4  +---+VID 42|
        +------+   +---------+   +------+

           VLAN-based Service Interface



               N:1                1:N
     +------+        +---------+        +------+
     |VID 11---------+         +--------+VID 12|
     +------+        +         +        +------+
     |VID 21+--------+         +--------+VID 22|
     +------+        +  EVI 1  +        +------+
     |VID 31+--------+         +--------+VID 32|
     +------+        +         +        +------+



Wang, et al.            Expires 9 September 2023                [Page 2]


Internet-Draft             L3 Accessible EVPN                 March 2023


     |VID 41+--------+         +--------+VID 42|
     +------+        +---------+        +------+

          VLAN-bundle Service Interface


            N:1                        1:N
               +----------------------+
     +------+  |+--------------------+|  +------+
     |VID 11+--++ Broadcast Domain 1 ++--+VID 12|
     +------+  |+--------------------+|  +------+
     |VID 21+--++ Broadcast Domain 2 ++--+VID 22|
     +------+  |+--------------------+|  +------+
     |VID 31+--++ Broadcast Domain 3 ++--+VID 32|
     +------+  |+--------------------+|  +------+
     |VID 41+--++ Broadcast Domain 4 ++--+VID 42|
     +------+  |+--------------------+|  +------+
               |                      |
               |        EVI 1         |
               +----------------------+

         VLAN-Aware Bundle Service Interface


     Figure 1: EVPN Service Interfaces Overview

   For VLAN-based service interface, there is a one to one mapping
   between VID and EVI.  Each EVI has a single broadcast domain so that
   traffic from different customers can be isolated.

   For VLAN-bundle service interface, there is a N to one mapping
   between VID and EVI.  Each EVI has a single broadcast domain, but the
   MAC address MUST be unique that can be used for customer traffic
   isolation.

   For VLAN-aware bundle service interface, there is a N to one mapping
   between VID and EVI.  Each EVI has multiple broadcast domains while
   the MAC address can overlap.  One broadcast domain corresponds to one
   VID, which can be used to customer traffic isolation.

   In the scenarios corresponding to these service interfaces, CE-PE
   should be placed in the same Layer-2 network.  In most of provider
   network, CE-PE need to cross a Layer-3 network, then the above
   service interfaces should be extended to adapt to the layer-3
   network.






Wang, et al.            Expires 9 September 2023                [Page 3]


Internet-Draft             L3 Accessible EVPN                 March 2023


   In this draft, we describe three layer-3 accessible interfaces for
   EVPN, summarize the existing layer-3 accessible EVPN solutions, and
   propose a new solution which can simplify the depolyment of layer-3
   accessible EVPN service.


2.  Conventions used in this document

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in [RFC2119] .

3.  Terminology

   The following terms are defined in this draft:

   *  CE: Client Edge

   *  PE: Provider Edge

   *  EVPN: BGP/MPLS Ethernet VPN, defined in [RFC7432]

   *  VxLAN: Virtual eXtensible Local Area Network, defined in [RFC7348]

   *  IPSec: Internet Protocol Security, defined in [RFC4301]


4.  Service Interfaces in layer-3 accessible EVPN

   In most of provider network, CE-PE need to cross a Layer-3 network.
   With this scenario, service interfaces defined in [RFC7432] should be
   extended to adapt to the layer-3 network.  To achieve the traffic
   isolation, tunnel encapsulation technologies can be used.

   We define Logical Session Identifier(LSI) to distinguish the packets
   from different tunnels, which is related to VNI/SPI.  The length of
   LSI is 16 bits.

   The layer-3 accessible interfaces for EVPN are shown in Figure 2,
   refer to [RFC7432]

                1:1           1:1
       +------+   +---------+   +------+
       |LSI 11+---+ IP-VRF1 +---+LSI 12|
       +------+   +---------+   +------+
       |LSI 21+---+ IP-VRF2 +---+LSI 22|
       +------+   +---------+   +------+
       |LSI 31+---+ IP-VRF3 +---+LSI 32|



Wang, et al.            Expires 9 September 2023                [Page 4]


Internet-Draft             L3 Accessible EVPN                 March 2023


       +------+   +---------+   +------+
       |LSI 41+---+ IP-VRF4 +---+LSI 42|
       +------+   +---------+   +------+

           LSI-based Service Interface



              N:1                1:N
    +------+        +---------+        +------+
    |LSI 11---------+         +--------+LSI 12|
    +------+        +         +        +------+
    |LSI 21+--------+         +--------+LSI 22|
    +------+        + IP-VRF1 +        +------+
    |LSI 31+--------+         +--------+LSI 32|
    +------+        +         +        +------+
    |LSI 41+--------+         +--------+LSI 42|
    +------+        +---------+        +------+

          LSI-bundle Service Interface


           N:1                        1:N
              +----------------------+
    +------+  |+--------------------+|  +------+
    |LSI 11+--++   Logical Plane 1  ++--+LSI 12|
    +------+  |+--------------------+|  +------+
    |LSI 21+--++   Logical Plane 2  ++--+LSI 22|
    +------+  |+--------------------+|  +------+
    |LSI 31+--++   Logical Plane 3  ++--+LSI 32|
    +------+  |+--------------------+|  +------+
    |LSI 41+--++   Logical Plane 4  ++--+LSI 42|
    +------+  |+--------------------+|  +------+
              |                      |
              |       IP-VRF 1       |
              +----------------------+

         LSI-Aware Bundle Service Interface



           Figure 2: Layer-3 accessible EVPN Service Interfaces Overview

   For LSI-based service interface, there is a one to one mapping
   between LSI and IP-VRF.  Each IP-VRF has a single logical plane so
   that traffic from different customers can be isolated.





Wang, et al.            Expires 9 September 2023                [Page 5]


Internet-Draft             L3 Accessible EVPN                 March 2023


   For LSI-bundle service interface, there is a N to one mapping between
   LSI and IP-VRF.  Each IP-VRF has a single logical plane, but the IP
   address MUST be unique that can be used for customer traffic
   isolation.

   For LSI-aware bundle service interface, there is a N to one mapping
   between LSI and IP-VRF.  Each IP-VRF has multiple logical planes
   while the IP address can overlap.  One logical plane corresponds to
   one LSI, which can be used to customer traffic isolation.

5.  Solutions of LSI-aware bundle service interface

   Let's assume a scenario as shown in Figure 3, where Backbone is EVPN
   domain, and the MANs are Layer-3 network.  VNIs in MANs are
   independently allocated, which may lead to the overlap of VNI in
   different customer sites.

+---+                                                                                  +---+
|C-A+--------+                                                                 +-------+C-A|
+---+        |      +-----------+   +-----------------+     +-----------+      |       +---+
           +-+--+   |           | +-+-+             +-+-+   |           |   +--+-+
           | CE +---+    MAN    +-+PE |  Backbone   |PE +---+    MAN    +---+ CE |
           +-+--+   |           | +-+-+             +-+-+   |           |   +--+-+
+---+        |      +-----------+   +-----------------+     +-----------+      |       +---+
|C-B+--------+                                                                 +-------+C-B|
+---+                                                                                  +---+

        Figure 3: LSI-aware bundle service interface scenario

   If each VNI has its own IP-VRF, each PE and CE maintain an IP-VRF for
   each deployment.  In this situation, customer traffic can be isolated
   by different VNIs, and there is no need for extending control plane/
   forwarding plane protocols.

   For deployment, we expect a simpler way, such as assign an IP-VRF to
   each customer, not to each department.  That is to say, all VNIs
   share one IP-VRF on PEs.  In this situation, each CE still maintain
   an IP-VRF for each deployment, but each PE maintains only one VRF for
   all deployments.  In this situation, customer traffic cannot be
   isolated by VNIs.  We propose a solution for this scenario:

   *  Using LSI information to identify different customer routes /
      traffic.  As described above, LSI can be generated by VNI/SPI, and
      there is a one to one mapping between LSI and VNI/SPI.  PEs should
      maintain the mapping table of LSI and VNI/SPI, so that they can
      distinguish different customer routes / traffic.  LSI information
      can be transmitted by using Ethernet Tag ID or a newly defined ESI
      type.



Wang, et al.            Expires 9 September 2023                [Page 6]


Internet-Draft             L3 Accessible EVPN                 March 2023


   *  TBD (more solutions are welcome).

   For example, the scenario shown in Figure 3 supports end-to-end L2/L3
   data transmission.  There is a N:1 mapping between LSI and EVI, 1:1
   mapping between LSI and VLAN ID, and 1:1 mapping between LSI and VNI,
   LSIs are used for traffic isolation.  If customers need end-to-end L2
   data transmission, the use of LSI is similar to VLAN ID.  If
   customers need end-to-end L3 data transmission, LSI can carry the
   identification information of customers through the layer-3 network.


6.  Protocol Extensions

6.1.  Forwarding Plane

6.1.1.  Extensions to VxLAN

   When the forwarding plane uses VxLAN tunnel technologies, we should
   extend the VxLAN GPE header to carry the LSI information, the
   extentions to the VxLAN GPE header is shown in Figure 4:

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |R|S|Ver|I|P|B|O|               LSI             |Next Protocol  |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                VXLAN Network Identifier (VNI) |   Reserved    |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

            Figure 4: The extentions to VxLAN GPE header

   We define a S bit.  If S is set to 1, it means the field after O bit
   contains LSI information.


6.2.  Control Plane

   We propose two methods to advertise LSI information in control plane:

   *  Reusing the Ethernet Tag ID field.  This method requires the
      update of [I-D.ietf-bess-evpn-prefix-advertisement] (Etherenet Tag
      ID is set to 0 for route type 5), and may arise some confuse with
      the original definition of Ethernet Tag ID.

   *  Using the newly defined ESI type as shown in Figure 5.  This
      method can preserve the original purpose of ESI definition (multi-
      homing).




Wang, et al.            Expires 9 September 2023                [Page 7]


Internet-Draft             L3 Accessible EVPN                 March 2023


                  +---+---+---+---+---+---+---+---+---+---+
                  | T | Reserved  | CE Identifier |  LSI  |
                  +---+---+---+---+---+---+---+---+---+---+


                   Figure 5: The format of new ESI type

   Where:

   *  T (1 octet): specify the ESI Type.  The recommended value is 0x06.

   *  CE Identifier (3 octets): the route ID/IPv4 address of CE.

   *  LSI (2 octets): the LSI information.

   Since the length of LSI is 16 bits, while the length of Ethernet Tag
   ID and ESI are 80 bits and 32 bits, respectively.  We can only use
   the lower 16 bits of Ethernet Tag ID / ESI field to carry LSI
   information, the other bits MUST set to 0.


7.  Modification of MAC/IP address storage mode on PE

   LSI-aware bundle service interface also changes the storage mode of
   MAC / IP address on PE, as shown in Figure 6.

 +--------------------------+             +--------------------------------+
 |MAC-VRF                   |             |IP-VRF                          |
 |                          |             |                                |
 |  BD-A (LSI <-> VNI)      |             |  Logical plane 1 (LSI <-> VNI) |
 |     MAC 1                |             |     IP Prefix 1                |
 |     ......               |             |     ......                     |
 |                          |             |                                |
 |  BD-B (LSI <-> VNI)      |             |  Logical plane 2 (LSI <-> VNI) |
 |     MAC 100              |             |     IP Prefix 100              |
 |     ......               |             |     ......                     |
 +--------------------------+             +--------------------------------+
   LSI-Aware Bundle Service                   LSI-Aware Bundle Service
         Interface(L2)                              Interface(L3)

     Figure 6: Modification of MAC/IP address storage mode on PE


   For end-to-end layer-2 data transmission, the storage mode of MAC
   address in MAC-VRF is similar to VLAN-aware bundle service, the only
   change is that different bridge domains are distinguished by LSI.





Wang, et al.            Expires 9 September 2023                [Page 8]


Internet-Draft             L3 Accessible EVPN                 March 2023


   For end-to-end layer-3 data transmission, sub-VRFs are needed in IP-
   VRF to storage IP address.  Different SDs are distinguished by LSIs.

8.  Security Considerations

   TBD

9.  IANA Considerations

   This draft extends the VxLAN GPE header, S bit of Flag and LSI field
   are added:

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |R|S|Ver|I|P|B|O|               LSI             |Next Protocol  |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                VXLAN Network Identifier (VNI) |   Reserved    |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   This draft also define a new ESI type:

                  +---+---+---+---+---+---+---+---+---+---+
                  | T | Reserved  | CE Identifier |  LSI  |
                  +---+---+---+---+---+---+---+---+---+---+

10.  Normative References

   [I-D.ietf-bess-evpn-prefix-advertisement]
              Rabadan, J., Henderickx, W., Drake, J., Lin, W., and A.
              Sajassi, "IP Prefix Advertisement in Ethernet VPN (EVPN)",
              Work in Progress, Internet-Draft, draft-ietf-bess-evpn-
              prefix-advertisement-11, 18 May 2018,
              <https://datatracker.ietf.org/doc/html/draft-ietf-bess-
              evpn-prefix-advertisement-11>.

   [I-D.ietf-bess-mvpn-evpn-aggregation-label]
              Zhang, Z. J., Rosen, E. C., Lin, W., Li, Z., and I.
              Wijnands, "MVPN/EVPN Tunnel Aggregation with Common
              Labels", Work in Progress, Internet-Draft, draft-ietf-
              bess-mvpn-evpn-aggregation-label-09, 12 December 2022,
              <https://datatracker.ietf.org/doc/html/draft-ietf-bess-
              mvpn-evpn-aggregation-label-09>.

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/RFC2119, March 1997,
              <https://www.rfc-editor.org/info/rfc2119>.



Wang, et al.            Expires 9 September 2023                [Page 9]


Internet-Draft             L3 Accessible EVPN                 March 2023


   [RFC2890]  Dommety, G., "Key and Sequence Number Extensions to GRE",
              RFC 2890, DOI 10.17487/RFC2890, September 2000,
              <https://www.rfc-editor.org/info/rfc2890>.

   [RFC4301]  Kent, S. and K. Seo, "Security Architecture for the
              Internet Protocol", RFC 4301, DOI 10.17487/RFC4301,
              December 2005, <https://www.rfc-editor.org/info/rfc4301>.

   [RFC7348]  Mahalingam, M., Dutt, D., Duda, K., Agarwal, P., Kreeger,
              L., Sridhar, T., Bursell, M., and C. Wright, "Virtual
              eXtensible Local Area Network (VXLAN): A Framework for
              Overlaying Virtualized Layer 2 Networks over Layer 3
              Networks", RFC 7348, DOI 10.17487/RFC7348, August 2014,
              <https://www.rfc-editor.org/info/rfc7348>.

   [RFC7432]  Sajassi, A., Ed., Aggarwal, R., Bitar, N., Isaac, A.,
              Uttaro, J., Drake, J., and W. Henderickx, "BGP MPLS-Based
              Ethernet VPN", RFC 7432, DOI 10.17487/RFC7432, February
              2015, <https://www.rfc-editor.org/info/rfc7432>.

Authors' Addresses

   Wei Wang
   China Telecom
   Beiqijia Town, Changping District
   Beijing
   Beijing, 102209
   China
   Email: weiwang94@foxmail.com


   Aijun Wang
   China Telecom
   Beiqijia Town, Changping District
   Beijing
   Beijing, 102209
   China
   Email: wangaj3@chinatelecom.cn


   Haibo Wang
   Huawei Technologies
   Huawei Building, No.156 Beiqing Rd.
   Beijing
   Beijing, 100095
   China
   Email: rainsword.wang@huawei.com




Wang, et al.            Expires 9 September 2023               [Page 10]