idr W. Kumari
Internet-Draft Google
Intended status: Informational K. Patel
Expires: April 25, 2012 Cisco Systems
J. Scudder
Juniper Networks
October 23, 2011
Automagic peering at IXPs.
draft-wkumari-idr-socialite-00
Abstract
This document describes a method for automatically establishing BGP
peering sessions at an Internet exchange point. Creation of these
peering sessions is facilitated by a host.
Status of this Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on April 25, 2012.
Copyright Notice
Copyright (c) 2011 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
Kumari, et al. Expires April 25, 2012 [Page 1]
Internet-Draft 'elo 'elo October 2011
described in the Simplified BSD License.
Table of Contents
1. Author Notes . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1. Changelog. . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.1. Requirements notation . . . . . . . . . . . . . . . . . . 4
3. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 4
4. Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
5. Protocol Extensions . . . . . . . . . . . . . . . . . . . . . 4
5.1. Debut Capability . . . . . . . . . . . . . . . . . . . . . 5
6. Packet Formats . . . . . . . . . . . . . . . . . . . . . . . . 5
6.1. Message Header . . . . . . . . . . . . . . . . . . . . . . 5
6.2. INTRODUCTION Record . . . . . . . . . . . . . . . . . . . 6
6.3. WITHDRAW Record . . . . . . . . . . . . . . . . . . . . . 7
7. Protocol operation . . . . . . . . . . . . . . . . . . . . . . 8
8. Operational overview / implications . . . . . . . . . . . . . 8
8.1. Additional eBGP sessions. . . . . . . . . . . . . . . . . 8
8.2. Simplified debugging. . . . . . . . . . . . . . . . . . . 9
8.3. BGP PATH / SIDR implications . . . . . . . . . . . . . . . 9
9. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 9
9.1. Debut TYPE registry . . . . . . . . . . . . . . . . . . . 9
10. Security considerations . . . . . . . . . . . . . . . . . . . 10
10.1. Privacy . . . . . . . . . . . . . . . . . . . . . . . . . 10
11. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 10
12. References . . . . . . . . . . . . . . . . . . . . . . . . . . 11
12.1. Normative References . . . . . . . . . . . . . . . . . . . 11
12.2. Informative References . . . . . . . . . . . . . . . . . . 11
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 11
Kumari, et al. Expires April 25, 2012 [Page 2]
Internet-Draft 'elo 'elo October 2011
1. Author Notes
[ RFC Editor -- Please remove this section before publication! ]
1. Choose a better name than "Debut"
1.1. Changelog.
o Changed the name of the protocol from 'elo-'elo to Debut - this is
still not great, but "Introduction" is worse.
o Added Operational section, incorporated notes from John Scudder,
Keyur.
2. Introduction
A large amount of Internet traffic is exchanged at Internet Exchange
Points (IXP). These are networks that are specifically built and
operated as locations for networks to peer and exchange traffic.
There are two primary types of peering that occur at IXPs, Public
Peering and Private Peering. Private peering usually involves two
parties entering some sort of contract, obtaining a dedicated circuit
between their routers and manually configuring a BGP peering session
between them (this is the standard BGP peering that one reads about
in all the textbooks!).
Public peering refers to peering across the (IXP provided) switch
fabric. In order to avoid having each participant at the IXP having
to contact all of the other participants to enter into peering
relationships, the IXP often provides a Route Server (RS). The Route
Server is a BGP speaker that participants peer with and announce
routes to. The Route Server takes these announcements and serves
them to all of the other participants who peer with it (so far this
is just like any other BGP router!). The Route Server differs from a
standard eBGP speaker in that it neither updates the Next Hop, nor
prepends its own AS to the AS Path attribute. By not changing the
Next Hop attribute, traffic between participants flows directly
between those participants (and does not pass through the Route
Server), as the traffic doesn't flow though it, it is appropriate
that it doesn't appear in the AS Path - this is known as a
transparent Route Server (by not showing up in the AS Path, the fact
that the peering between the participants occurs over a public
peering session is hidden, and participants are not penalized by
having longer AS Paths).
This document describes an alternate solution for peering at an IXP.
Instead of having a server that re-announces the routes from each
participant to all of the others, we introduce a "socialite", a
Kumari, et al. Expires April 25, 2012 [Page 3]
Internet-Draft 'elo 'elo October 2011
devices that is responsible to making introductions between all of
the participants and facilitating connections between them. This
socialite can be though of like a host at a dinner party. The guests
arrive and the socialite introduces them to each other, and then
steps out of the way to allow them to communicate (and peer!) on
their own.
2.1. Requirements notation
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
3. Terminology
[TODO (WK): Fill this in! :-P ]
Internet Exchange Point A network, usually with a large, fast switch
fabric, designed for exchanging BGP routing information and
traffic.
Route Server A BGP speaker at an IXP that "reflects" routes from one
participant to all the other participants. See
[I-D.jasinska-ix-bgp-route-server]
Transparent Route Server A route server that doesn't add itself to
the AS Path, and so is invisible from outside the ISP.
Sociatite A device running the Introduction protocol, responsible
for making introductions between Guests.
Guests Participants of the IXP that speak the Debut protocol with
the Socialite, and are introduced by the Socialite to other
Guests.
Debut The protocol spoken between the Socialite and the Guests.
4. Overview
The Guests at the IXP form a BGP peering relationship with the
Socialite, announcing support for the Debut protocol. The Socialite
sends the Guests a set of Debut updates, containing informations
about the other participants. The Guests use this information to
form direct BGP peerings between themselves. Policy can be
configured on the Socialite to only make introductions between
subsets of participants if so desired.
5. Protocol Extensions
The BGP protocol extensions introduced in this document include the
definition of a new BGP capability, named "'Debut Capability", and
Kumari, et al. Expires April 25, 2012 [Page 4]
Internet-Draft 'elo 'elo October 2011
the specification of the message subtypes for the Debut messages.
5.1. Debut Capability
The "Debut Capability" is a new BGP capability [RFC5492]. The
Capability Code for this capability is specified in the IANA
Considerations section of this document. The Capability Length field
of this capability is zero. By advertising this capability to a
peer, a BGP speaker conveys to the peer that the speaker supports the
message subtypes for the Debut protocol and the related procedures
described in this document.
6. Packet Formats
The Debut protocol is implemented using TLV structures, and
(unsurprisingly) fields are in network byte order. These TLV records
are carried as payload in a standard BGP Message packet (RFC 4271,
Section 4.1. Message Header Format ) [RFC4271]
6.1. Message Header
The Debut protocol is implemented using the standard Type-Length-
Value paradigm.
All Debut messages are carried as payload in a standard BGP Message
of Type [TBD_BGP] and are preceded by a standard header that specific
the type and length of the message.
0 1 2 3 4 5 6 7 15 31
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| VER | RES | TYPE | LENGTH |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| VALUE (Variable Length) |
~ ~
~ ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
o VER (4 bits): The VER (version) field specifies the version of the
Debut protocol. For the initial (this) version of the protocol it
will be set to 0.
o RES (4 bits): The RES (reserved) field is reserved in the initial
(this) version of the protocol. It SHOULD be initialized to 0 on
transmit and should be ignored on reception.
o TYPE (2 octets): The TYPE field species the TYPE of the TLV
record, and allows an implementation to determine what type of
information is carried in the record. If the highest bit of the
Kumari, et al. Expires April 25, 2012 [Page 5]
Internet-Draft 'elo 'elo October 2011
TYPE field is set (the TYPE value is >= 32786), understanding /
implementation of the TYPE is optional - if an implementation does
not implement this type it may ignore this message (this
capability is included to allow for possible future logging,
diagnostics, etc). If the highest bit is not set, and the
implementation receives a TYPE that it does not implement, it
should send a BGP NOTIFY and tear down the session. The TYPE
codes are defined in the
o LENGTH (2 octets): The number of octets in the VALUE field of the
TLV record. The total length of the TLV record in octets can be
calculated by adding 4 (the number of octets in the TYPE and
LENGTH fields) to the value of this field. This allows
implementations to skip over TLV records that it cannot handle.
o VALUE (Variable length): The actual data. The meaning of this
data is given by the TYPE filed, and the length by the LENGTH
field. Parsing of the data field is performed according to the
value of the TYPE field.
6.2. INTRODUCTION Record
INTRODUCTION (TYPE 0) TLV records are used to "make introductions"
between the Guests speaking the Debut protocol. They carry the
information needed by Guests to contact the other Guests and
establish a BGP peering session.
0 1 2 3 4 5 6 7 15 24 32
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
0: | NEIGHBOR AS |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
4: | AFI | SAFI | LEN |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ADDRESS |
+---+---+---+---+---+---+---+---+---+---+---+---+---+---+---+---+
/ /
+---+---+---+---+---+---+---+---+---+---+---+---+---+---+---+---+
x: | Auth |
+---+---+---+---+---+---+---+---+---+---+---+---+---+---+---+---+
o NEIGHBOR AS (4 octets): This specifies the Autonomous System of
the Guest being introduced. In "Four-octet AS Number" format as
specified in RFC4893 [RFC4893]
o AFI (2 octets): Address Family Identifier [RFC2858] [RFC2858]
o SAFI (1 octet): Subsequent Address Family Identifier [RFC2858]
[RFC2858]
o LEN (1 octet): The length of the address in the ADDRESS field (32
for IPv4, 128 for IPv6).
Kumari, et al. Expires April 25, 2012 [Page 6]
Internet-Draft 'elo 'elo October 2011
o ADDRESS (Variable length) This contains the IP Address of the
Guest being introduced.
o Auth (optional, variable length): The existence of this filed is
determined from LENGTH of the TLV. If the LENGTH is greater than
the length of NEIGHBOR AS, FAMILY and ADDRESS, there is Auth data
(ick!). This data is used to authenticate connections to the
guest. [TODO (WK): Figure this out! ]
The AFI and SAFI are included in the INTRODUCTION message to allow
the Socialite to introduce Guests with multiple address families.
On reception on an INTRODUCTION message a Guest should store the
information and then consult ([TODO(WK): Define) local policy (if
any) to determine if it is willing to peer with the newly introduced
Guest. If so, it should proceed as though this were a manually
configured peer [TODO(WK): I think that this avoids the race
condition?] (although it (obviously) should not insert this in the
config, etc).
6.3. WITHDRAW Record
WITHDRAW (TYPE 1) TLV records are used to inform a Guest that a
another previously introduced Guest is not longer participating. A
Guest can use this information to abort in progress connection
attempts, invalidate information from a cache, for informational
logging or in any other way is sees fit, but it SHOULD NOT use this
information to tear down peering sessions to other Guests in
ESTABLISHED state. Debut is intended to make initial introductions
between participants and does not provide any mechanisms to
invalidate / abort sessions once the introductions have been made.
If a Socialite attempt to unintroduce an unknown Guest, this
information should be logged and then ignored.
0 1 2 3 4 5 6 7 15 24 32
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
0: | AFI | SAFI | LEN |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
4: | ADDRESS \
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
o AFI (2 octets): Address Family Identifier [RFC2858] [RFC2858]
o SAFI (1 octet): Subsequent Address Family Identifier [RFC2858]
[RFC2858]
o LEN (1 octet): The length of the address in the ADDRESS field (32
for IPv4, 128 for IPv6).
Kumari, et al. Expires April 25, 2012 [Page 7]
Internet-Draft 'elo 'elo October 2011
o ADDRESS (Variable length): This contains the IP address of the
Guest that is no longer participating.
The AFI and SAFI are included so that the Socialite can inform Guests
that only one of the AFI / SAFIs is being removed.
7. Protocol operation
Debut BGP sessions behave just like any other BGP sessions, just the
information carried is different - Guests should use the standard BGP
peering process to contact Socialites (or Socialites, Guests). Once
the peering is ESTABLISHED, Guests will begin receiving INTRODUCTION
messages in UPDATES, and will store them in something resembling Adj-
RIB-IN. Standard BGP logic applied for things like error handling,
invalidation of previously received information, etc.
As Debut is only intended to make initial introductions between
Guests (and not to manage sessions between those Guests), if the BGP
session between Guest and Socialite goes down, established BGP
peerings between Guests will continue to remain active.
8. Operational overview / implications
There are many reasons why participants peer with route-servers at
IXPs (see [I-D.jasinska-ix-bgp-route-server]) including
o reducing the administrative burden of arranging and configuring
BGP sessions with all the other participants,
o not wanting (or being able) to carry views from all the
participants,
o relying on the IXP operator to implement routing policy decisions
(see [I-D.jasinska-ix-bgp-route-server], section 2.3)
This solution only attempts to address the first reason for using a
route-server, and the implications of deploying this are described
below.
8.1. Additional eBGP sessions.
Debut is used to make introductions between all (or a subset of)
participants at an IXP, and then the participants peer over "regular"
BGP peerings. This means that each participating router will build a
separate BGP peering session with every other participating router.
As participants at IXPs (usually) only advertise a small subset of
the full Internet routing table (such as internal or customer routes)
and there is (usually) not a huge overlap of this routing
information, the additional memory requirements are expected to not
Kumari, et al. Expires April 25, 2012 [Page 8]
Internet-Draft 'elo 'elo October 2011
be too onerous (especially with the capacity of modern routers). As
with all operational matters though, "Your network, your rules"
applies -- it is up to each operator to determine the applicability /
utility of the solution and how it fits (or doesn't) into their
network (see what I did there? If this ends poorly, it's your own
fault!)
8.2. Simplified debugging.
As "normal" eBGP peering sessions are setup between the participants
(and there is no third party performing route-selection, etc),
operators have more visibility into the system and can more easily
leverage their existing troubleshooting / debugging skills to debug
issues. Debut also more closely aligns the data and control plane,
etc.
8.3. BGP PATH / SIDR implications
Part of the justification for this work is to simplify the design and
implementation of path security in SIDR ([TODO(WK): Find a good
reference!). As a Route-Server passes routing information between
peers, but does not show up in the BGP AS-PATH it is
indistinguishable from a BGP path shortening attack. By using Debut,
eBGP speakers peer directly with each other and this problem is
avoided.
9. IANA Considerations
IANA is requested to assign an AFI and SAFI for the Debut protocol.
The text TBD1 should be replaced with the allocated AFI and the text
TBD2 should be replaced with the allocated SAFI (and then this
sentence should be removed).
The IANA is requested to assign a value from the "BGP Message Types"
registry and replace the text [TBD_BGP] with this value. The
definition should be "Debut protocol".
TODO(WK): Figure this out. How are these actually carried? In
vanilla BGP? MPBGP? What?!
9.1. Debut TYPE registry
This document creates a new registry, "Debut Message Types".
The registry policy is ""Specification Required".
The initial entries in the registry are:
Kumari, et al. Expires April 25, 2012 [Page 9]
Internet-Draft 'elo 'elo October 2011
Value Short description Reference
-------------------------------------------------
0 INTRODUCTION [This]
1 WITHDRAW [This]
2-3200 Unassigned
3200-32767 Private Use
32768-65480 Unassigned
65481-65535 Private Use
Applications to the registry can request specific values that have
yet to be assigned.
10. Security considerations
TODO(WK): Fill this in!
This protocol is designed to facilitate direct BGP peerings between
participants at an IXP, which eliminates the need for transparent
route servers (which do not show up in the AS_PATH). This will
facilitate the deployment of SIDR.
As participants peer with each other directly (and not through a
third party) there is less opportunity for malicious tampering with
the control plane (for example, by the IXP).
Debut currently does not provide a means to securely distribute
Authentication information (there is a field, but it's not really
defined). Depending on if needed this may be addressed.
An attacker who manages to subvert the Socialite (or inject UPDATES
that into the Socialite to Guest communication) will be able to make
Guests peer with a device under his control. An attacker with this
capability could (I think!) cause equal or more harm with the current
route-server design, so....
10.1. Privacy
By having participants peer directly (as opposed to having their
routing information pass through a route-server) the routing
information is hidden from the IXP / route-server operator. Please
note that this doesn't protect the data-plane, and the routing
information could still be sniffed off the wire.
11. Acknowledgements
I would like to thank Google for 20% time.
Kumari, et al. Expires April 25, 2012 [Page 10]
Internet-Draft 'elo 'elo October 2011
12. References
12.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2858] Bates, T., Rekhter, Y., Chandra, R., and D. Katz,
"Multiprotocol Extensions for BGP-4", RFC 2858, June 2000.
[RFC4271] Rekhter, Y., Li, T., and S. Hares, "A Border Gateway
Protocol 4 (BGP-4)", RFC 4271, January 2006.
[RFC4893] Vohra, Q. and E. Chen, "BGP Support for Four-octet AS
Number Space", RFC 4893, May 2007.
12.2. Informative References
[I-D.jasinska-ix-bgp-route-server]
Jasinska, E., Hilliard, N., Raszuk, R., and N. Bakker,
"Internet Exchange Route Server",
draft-jasinska-ix-bgp-route-server-02 (work in progress),
March 2011.
Authors' Addresses
Warren Kumari
Google
1600 Amphitheatre Parkway
Mountain View, CA 94043
US
Email: warren@kumari.net
Keyur Patel
Cisco Systems
Phone:
Fax:
Email: keyupate@cisco.com
URI:
Kumari, et al. Expires April 25, 2012 [Page 11]
Internet-Draft 'elo 'elo October 2011
John Scudder
Juniper Networks
1194 N. Mathilda Ave
Sunnyvale, CA
USA
Phone:
Fax:
Email: jgs@juniper.net
URI:
Kumari, et al. Expires April 25, 2012 [Page 12]