MIF Hongke Zhang
Internet Draft Fei Song
Intended status: Informational Boxin Du
Expires: May 18 2019 Mi Zhang
Beijing Jiaotong University
Nov 15,2018
MIF API extension for combining IEEE 802.2
draft-zhang-mif-api-extension-802-21-09.txt
Status of this Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six
months and may be updated, replaced, or obsoleted by other documents
at any time. It is inappropriate to use Internet-Drafts as
reference material or to cite them other than as "work in
progress." This Internet-Draft will expire on May 18, 2019.
Copyright Notice
Copyright (c) 2016 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with
respect to this document. Code Components extracted from this
document must include Simplified BSD License text as described in
Section 4.e of the Trust Legal Provisions and are provided without
warranty as described in the Simplified BSD License.
Zhang, et al. Expires May 15, 2019 [Page 1]
Internet-Draft MIF API extension Nov 2018
Abstract
The Application Program Interface (API) of MIF, specified in the MIF
API consideration, must rely on lower layer functionalities when
handover between homogeneous or heterogeneous networks is necessary.
To improve the connectivity performance, the existing MIF API needs
to be extended. IEEE is also aimed at the similar issue from
different way. A kind of logical entities over the link layer
protocol for handling the seamless handover has been defined in
IEEE802.21. This document proposes a mechanism via integrating MIF
API and IEEE 802.21 to support application service better.
Table of Contents
1. Introduction ................................................ 3
2. Terminology ................................................. 3
3. The Relationship between IEEE MIHF and MIF API ...............4
4. The Extension of MIP API for Handover: A Case Study...........7
4.1. The MN-initiated Handover............................... 8
4.1.1. Get Information.................................... 8
4.1.2. Information Post................................... 8
4.1.3. Parameter Report................................... 8
4.1.4. Check Resources MN................................. 9
4.1.5. Resource Availability.............................. 9
4.1.6. Connect to Interface............................... 9
4.1.7. Resource Preparation Messages ......................9
4.1.8. Establish Link Messages............................ 9
4.1.9. Link Up .......................................... 10
4.1.10. Handover Completed............................... 10
4.1.11. Handover Completion Confirmation .................10
4.2. The Network-initiated Handover .........................10
4.2.1. Candidate Query Notification ......................11
4.2.2. Candidate Query Result............................ 11
4.2.3. Check Resources Net............................... 11
4.2.4. Confirm Chosen Target............................. 11
4.2.5. Establish Link Messages........................... 12
4.2.6. Link up .......................................... 12
4.2.7. Handover Completed................................ 12
4.2.8. Handover Completion Confirmation ..................12
5. Discussions for New Messages from MIF Perspective ...........12
5.1. Get Information........................................ 12
5.2. Release the Ongoing Connection .........................12
5.3. Establish New L2 Connection............................ 13
6. Discussions for New Messages from IEEE Perspective ..........13
7. Security Considerations..................................... 16
8. IANA Considerations ........................................ 16
Zhang, et al Expires May 15, 2019 [Page 2]
Internet-Draft MIF API extension Nov 2018
9. References ................................................. 16
9.1. Normative References................................... 16
9.2. Informative References................................. 16
10. Acknowledgments ........................................... 16
1. Introduction
In MIF context, the improvement of connectivity experiences SHOULD
be produced. The main target is to enhance the performance of
horizontal and vertical switches between networks. The
aforementioned situation is quite similar with Media Independent
Handover (MIH) described in [IEEE 802.21]. Even though the MIF
Application Program Interface (API) specified in the MIF API
consideration [I-D.ietf-mif-api-extension] illustrates a series of
message in multiple interface scenarios, this draft only provides a
minimal set of message calls REQUIRED to implement the API. Hence,
new functions could be added.
In terms of [IEEE 802.21], the Media Independent Handover Function
(MIHF) is a logical entity, which can facilitate MIH decision making
based on inputs from the MIHF. MIHF can provide abstracted services
for higher layers. Also, it can communicate with the lower layer of
the mobility-management protocol stack through technology specific
interfaces in MIHF.
As two mechanisms, MIF API and MIHF, are working in different layers
and defined by different organizations. Thus, the requirements of
compatibility are distinct. Connection manager (i.e. the MIHF)
SHOULD support some of the functions of MIF API, and vice versa.
The MIF API can use the capabilities of MIHF to hand over issues
based on the advantages of MIHF and its Service Access Point (SAP).
Message calls of MIF API is extended by this document to support the
MIH. Similar with [I-D.ietf-mif-api-extension], because they are left
up to the implementation, there are no bindings for programming
languages being provided. This document only illustrates the messages
sending and receiving, which can be read as a checklist for operating
system vendors.
2. Terminology
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC-2119 [RFC2119].
Zhang, et al Expires May 15, 2019 [Page 3]
Internet-Draft MIF API extension Nov 2018
3. The Relationship between IEEE MIHF and MIF API
The purpose of IEEE 802.21 is to further the user experience of
mobile devices through facilitating handover among all IEEE.802
networks despite of whether they are of different media types or
not, including both wired and wireless. Also, the target is to make
it possible for mobile devices to perform seamless handover between
IEEE 802 and non IEEE networks. This standard defines:
1. A framework that enables service continuity while a Mobile Node
(MN) transitions between heterogeneous link-layer technologies.
2. MIHF
3. MIH_SAP and associated primitives for users to get services of
MIHF.
4. The definitions of new link-layer SAPs and associated primitives
for each link-layer technology. They help MIHF to collect link
information and control link behaviors during handovers.
MIHF is a functional entity to fulfill the high- performance
handovers. The fundamental advantage of MIHF is that it provides
media-specific technology of lower layer is being used, such as IEEE
Std.802.3, IEEE Std.802.11, IEEE Std.802.16, 3GPP and 3GPP2.
Besides, three kinds of SAPs (will be detailed later) of MIHF are
also defined and their primitives that interact between different
layers.
The MIHF can also act as a filter: the messages received from link
layer SHOULD be processed and submitted to higher layer for meeting
the subscribers' need. Therefore, MIHF should work under MIF API. In
fact, MIF API SHOULD be served as a user of MIHF, as shown in Figure
1. The subscribers can then only interact with the MIHF via one kind
of SAPs (i.e. MIH_SAP) without knowing the lower things. The MIH
protocol is not in the scope of this document.
Three kinds of MIHF services are defined in the standard: Media
Independent Event Service (MIES), Media Independent Command Service
(MICS) and Media Independent Information Service (MIIS).
MIES provides event's degree, for event filtering and event
reporting corresponding to dynamic changes in link characteristics,
link status and link quality. It originates from lower layers and
can be passed to MIHF or upper layers for the detection of handover
requirement. MTH users manage and control link behavior related to
Zhang, et al Expires May 15, 2019 [Page 4]
Internet-Draft MIF API extension Nov 2018
handover and mobility through MICS. It is invoked by users or MIHF
and has an impact on MIHF or lower layers.
For example, in MN-initiated handover scenario, MICS is adopted for
MN switching between different links. MIIS makes it possible for MN
and network entities discovering information which has influence on
the selection of appropriate networks during handovers. Figure 2
[IEEE 802.21] shows MIH services and their initiation.
+------------------------------------------------------+
| |
| Application |
| |
+---+--------+-------+---+------------+-----+----------+
^ | ^ | ^ |
| | | | | |
| v | | | |
+---+--------+----+ | | | |
| | | | | |
| High Level API | | | | |
| | | | | |
+---+--------+----+ | | | |
^ | | | | |
| | | | | |
| v | v | |
+---+--------+-------+---+----+ | |
| | | |
| MIF API | | |
| | | |
+---+--------+----------------+ | |
| | | v
| | +----------------+-----+-----------+
| | | |
| | | Communication API |
| | | |
| | +---------+----+-------------------+
| | ^ ^
| | | |
| | v v
+---+--------+-----------------+----+-------------------+
| |
| MIHF |
| |
Zhang, et al Expires May 15, 2019 [Page 5]
Internet-Draft MIF API extension Nov 2018
+-------------+------------------------+----------------+
^ |
| |
+-------------+------------------------v----------------+
| |
| Network Link API |
| |
+------+--------+-----------------------+-------+-------+
^ | ^ |
| | | |
| | | |
+------+--------v-----+ +------+-------v-------+
| | | |
| Network | | Network |
| Interface 1 | | Interface 2 |
| | | |
+---------------------+ +----------------------+
The relationship of the MIHF & MIF API
The letters a, b, c in Figure 2 respectively represent:
a. MIH_SAP
b. MIH_LINK_SAP
c. LLC_SAP
The SAPs are divided into two categories:
1) Media dependent SAP (including MIH_LINK_SAP and LLC_SAP).
2) Media independent SAP (MIH_SAP).
+--------------+-+ Command +--------------------------------+
| | Service | |
| | | MIH User |
| +--+--+ <---------+ | |
| | | | Layer 3 or Higher |
| MIHF | | Event | Mobility Protocol |
| | | Service | |
| Event | a | | |
| Service | | +-----------> | |
| | | Information | |
Zhang, et al Expires Nov 18, 2018 [Page 6]
Internet-Draft MIF API extension Nov 2018
| Command | | Service | +--------+ +--------+ |
| Service | | +---+ c +-+----+--+ c +--+
| +--+--+ <----------> | | | | | | | |
| Information | Command | +--------+ | | +-----+ |
| Service | Service +-+--+ | | |
| | | | | | |
| | +-----------> | | | | |
| | Event | | Network1 | +-+--+ Network2 |
| | Service | b | (e.g.IEEE | | |(e.g.IEEE |
| | | | 802.16) | | b | 802.11) |
| | <----------+ | | | | | |
| | Information| | | | | |
| | Service | | | | | |
| | +-+--+ | | | |
| | <------------> | | +---++ |
| | | | | |
| | | | | |
| | +--------------+ +-----------+
+--------------+
MIH services and their initiation
SAP of the MIHF (i.e. MIH_SAP) is media independent. The interface
between the MIHF and MIH users is defined by the MIH_SAP such as an
upper layer mobility protocol or a handover function (e.g., MIF API)
that might reside at higher layer transport entity as well.MIHF is
allowed by MIH_SAP to provide services to the upper layers, the
network management plane and the data bearer plane. Upper layers
need to subscribe with the MIHF as users to receive MIHF events. In
MIF case, the MIF API can send commands to the local MIHF via
messages which uses the service primitives of the MIH_SAP directly.
All the messages REQUIRED for communicating successfully in MIF
environment that described in the [I-D.ietf-mif-api-extension] MUST
also be used here. These messages define how the MIF API interacts
with higher layers or applications and need to be added to this
collection for the switching process. These new messages SHOULD
be exchanged between MIHF and MIF API. The service of MIHF is used
by some of them.
4. The Extension of MIP API for Handover: A Case Study
This section introduces the extension of message calls of MIF API in
two parts based on the classification of handovers (MN-initiated
handover and the network-initiated handover). In order to handle
these two kinds of handovers successfully, MIF API SHOULD be
extended respectively based on the characteristics of process.
Zhang, et al Expires May 15, 2019 [Page 7]
Internet-Draft MIF API extension Nov 2018
4.1. The MN-initiated Handover
The handover initiated by MN includes the following seven steps:
1) Information query. The MN collects network information from the
MIIS server which the MN is connected to.
2) Resource availability check. The MIF API sends request to find
candidates and then receives a list of candidate networks in
response message.
3) Resource preparation. The MN SHOULD determine which target
network is suitable and request it for resource preparation.
4) Establish new L2 connection. The MIF API initiates a new link
connection.
5) Link up indication. The MIHF of MN notifies the MIF API that the
link is up.
6) Higher layer handover execution.
7) Resource release. The original serving network resources must be
released in the end.
The following messages need to be added, which describes
interactions between a MIHF and MIF APIs.
4.1.1. Get Information
This message is sent by the MIF API for the inquiry of the
neighboring networks information. In MIH, the MIH_Get_Information is
used to request for the same purpose. After receiving this message,
the MIHF inquires the MIIS server for the information, which will
return a list of network information for MIF API.
4.1.2. Information Post
This message is sent to the MIF API by the MIIS server as a response
to the Get Information message. MIH_Get_Information confirm can be
used to convey such information.
4.1.3. Parameter Report
The lower layers link status needs to be sent to the MIF API to
better control the whole connection when connecting to a specific
network. Reports can be sent to the MIHF from the link layers and
Zhang, et al Expires May 15, 2019 [Page 8]
Internet-Draft MIF API extension Nov 2018
then submit to the higher layers. If the link is going down, the MIF
API must notify its subscribers using "Interface is going away"
message. The application or higher API SHOULD establish new
connections by sending "Wants to connect" to MIHF and the connection
process will restart from step 2 (i.e. Resource availability check).
Another situation is, when the MIF API receives a "Wants to connect"
message from its subscriber, it SHOULD trigger a whole connection
process to a new network accordingly. This can also begin from step
2.
4.1.4. Check Resources MN
In the connection starts period, the resource availability SHOULD
be checked by the MN at the candidate networks. This message is sent
to the MIHF by the MIF API. The service network should then request
each candidate. The higher layer can receive the final result. The
MIH_MN_HO_Candidate_Query request can be used in the MIH case.
4.1.5. Resource Availability
When receiving the resource availability of the candidates from the
serving network, the MIHF SHOULD submit these messages to the MIF
API. The MIH_MN_HO_Candidate_Query confirm can be used in the MIH
case.
4.1.6. Connect to Interface
This message is sent to the MIF API by the upper applications. When
the MIF API receives the Resource Availability, it could post the
message to the higher layer. The upper application use "Connect to
Interface" to choose a better network interface. More about the
choosing methods need further discussion.
4.1.7. Resource Preparation Messages
The MIF API can use the MIH_MN_HO_Commit request, which includes the
target network information to request the network chose for resource
preparation. The MIHF receives the response from the target network
when the preparation is done. In order to inform the status of the
previously issued target notification request, it sends a
MIH_MN_HO_Commit confirm message to the MIF API.
4.1.8. Establish Link Messages
The connection establishment problem can be solved by MIF API using
the MIH_Link_Action request. The [IEEE 802.21] defines this message
Zhang, et al Expires May 15, 2019 [Page 9]
Internet-Draft MIF API extension Nov 2018
primitively to control the local or remote lower link layers. It
includes a MIHF ID and a Link Actions List, which can realize many
controlling functions. The MIF API should receive a MIH_Link_Action
confirm to indicate the result, after the action having been
executed.
4.1.9. Link Up
After the new link being established, a Link_Up indication is
delivered by MAC layers to MIHF. The MIHF then passes the
MIH_Link_Up indication message to the MIF API. The MIF API can
notify the upper applications using the "Link is going up" message.
Then the higher layer handover execution might be triggered and the
traffic flow can be re-established.
4.1.10. Handover Completed
This message is sent to the MIF API by the MIHF, which indicates
that the resource of the previous network is successfully released.
4.1.11. Handover Completion Confirmation
This message is sent to the MIF API by the MIHF indicating that the
resource of the previous network is successfully released.
4.2. The Network-initiated Handover
There are also seven steps in an intact network-initiated handover,
like the MN-initiated handover:
1) Information query.
2) Resource availability check.
3) Resource preparation.
4) Establish a L2 connection using MIH_Link_Action request.
5) Sent link indications to the MIF API.
6) Higher layer handover execution.
7) Resource release.
The differences between Network-initiated case and MN-initiated case
are in step 1 and step 2. The MIH user of the serving network can
initiate the Get Information Request and Information Query
Zhang, et al Expires May 15, 2019 [Page 10]
Internet-Draft MIF API extension Nov 2018
respectively. Such MIH user will send requests to the MN for a
response message containing the MN's handover acknowledgement
for MN's preferring link and PoS lists, when it obtains the
information from the MIIS server.
In step 3, the commitment of target network is also initiated by the
MIH user of the service network. After the resource being prepared,
the PoS of serving network SHOULD notify the MN for the
establishment of L2 connection in step 4.
The following messages should be added in MIF API.
4.2.1. Candidate Query Notification
MN's MIHF receives this message from the PoS of the serving network
with a list of PoAs of each candidate network link. Such message
suggests the MN SHOULD consider new access network. This message can
use the MIH_Net_HO_Candidate_Query indication.
4.2.2. Candidate Query Result
This message is sent to the local serving network's MIHF from MN's
MIF API, specifying whether the request of handover is permitted or
not. MIH_Net_HO_Candidate_Query response can be used here. When the
handover is allowed, the new access network SHOULD be considered
during the handover initiation phase.
4.2.3. Check Resources Net
This message is sent to the MN's MIF API by the PoS of serving
network with a list of target network information and a set of
resource parameters assigned to the MN for handover.
MIH_Net_HO_Commit indication can be used. Then the establishment of
L2 can be triggered by the MIF API using Link_Action request. After
the link connection is done, MIF API needs inform the serving
network. Link_Action request might also have a list of actions for
handover control during the link connection period.
4.2.4. Confirm Chosen Target
The MN's MIF API sent this message as a response to the
MIH_HO_Commit indication, revealing that the indication is received.
MIH_Net_HO_Commit response can be used. Also such message might
include a list of the results of previous actions.
Zhang, et al Expires May 15, 2019 [Page 11]
Internet-Draft MIF API extension Nov 2018
4.2.5. Establish Link Messages
This message is exactly the same as that of the MN-initiated
process, for establishing a new L2 link connection.
4.2.6. Link up
This message is exactly the same as that of the MN-initiated
process, for informing the MIF API that the L2 link is completed.
4.2.7. Handover Completed
This message is exactly the same as that of the MN-initiated
process, for releasing the resources that have already attained by
the MN.
4.2.8. Handover Completion Confirmation
This message is exactly the same as that of the MN-initiated
process, for confirming that the resources of the previous network
are successful.
5. Discussions for New Messages from MIF Perspective
New messages described in this document are critical for information
exchanging and function achievement between MIHF and MIF API. Since
both "upper layer requirements gathering" and "lower layer command
delivering" (or reverse) can be achieved via messages, the logical
relationship should be discussed in-depth. The bellowing messages
are only the examples. Further updating is needed.
5.1. Get Information
According to [IEEE 802 21], this information query is related to a
specific interface. It has the flexibility to query either a
specific data within a network interface or an extended schema of a
given network. As "Announce Interface", "Announce PVD" and "Announce
IE(Information Elements)" are sent by an advanced application or
upper APIs, the MIF API could obtain the information via the
Get_information request in MIH.
5.2. Release the Ongoing Connection
The [I-D.ietf-mif-api-extension] defines a message "Connection can
be broken", which means that the MN can tolerate the connection
being broken, e.g. for power conservation. When the subscribers of
MIF API delivers this message, the MIF API SHOULD send "Release the
Zhang, et al Expires May 15, 2019 [Page 12]
Internet-Draft MIF API extension Nov 2018
ongoing connection" to the MIHF so that directly releasing the
current resources of network to cut off this connection, which will
not weaken the application function.
5.3. Establish New L2 Connection
According to [IEEE 802.21], a L2 link connection can be triggered by
the MIH_Link_Actions. The MIF API will receive "Connect to Address"
or "Connect to Address from Address" messages, when MN wants to
build a TCP connection with an IP host. Then the MIF API can use the
MIH_Link_Actions request to ask MIHF for new L2 link connection.
6. Discussions for New Messages from IEEE Perspective
The following tables, table1, 2, 3 and 4 are from the [IEEE 802.21].
These messages might be used in the MIF API, because they are
exchanged between the MIHF and its MIH users. Even though some of
them have been discussed above, the specific usage of the rest is
not represented. This section presents only a direct list of their
category and brief descriptions. Further discussion is needed.
+---------------------+-------------------------------------------+
| Messages | Description |
| (Information) | |
+---------------------+-------------------------------------------+
| MIH_Get_Information | Request to get information from repository|
+---------------------+-------------------------------------------+
| MIH_Push_Information| Notify the MN of operator policies or |
| | other information |
+---------------------+-------------------------------------------+
Table 1 Information Messages of MIHF
+---------------------+--------------------------------------------+
| Messages (Event) | Description |
+---------------------+--------------------------------------------+
| MIH_Link_Detected | Link of a new access network has been |
| | detected. This event is typically on |
| | the MN when the first PoA of an access |
| | network is detected |
+---------------------+--------------------------------------------+
| Track_timeout | This event is not generated when |
| | subsequent PoAs of the same access |
| | network are discovered |
+---------------------+--------------------------------------------+
| MIH_Link_Up | L2 connection is established and link |
| | is available for use |
Zhang, et al Expires May 15, 2019 [Page 13]
Internet-Draft MIF API extension Nov 2018
+---------------------+--------------------------------------------+
| MIH_Link_Down | L2 connection is broken and link is |
| | not available for use |
+---------------------+--------------------------------------------+
| MIH_Link_Paremeters | Link parameters have crossed a speci- |
| _Report | fied threshold and need to be reported |
+---------------------+--------------------------------------------+
| MIH_Link_Going_Down | Link conditions are degrading and |
| | connection loss is imminent |
+---------------------+--------------------------------------------+
| MIH_Link_Handover | L2 handover is imminent based on ei- |
| _Imminent | ther the changes in the link condition |
| | or additional information available in |
| | the network |
+---------------------+--------------------------------------------+
| MIH_Link_Handover | L2 handover to a new PoA has been |
| _Complete | completed |
+---------------------+--------------------------------------------+
| MIH_Link_PDU | Indicate transmission status of a PDU |
| _Transmit_Status | |
+---------------------+--------------------------------------------+
Table 2 Event Messages of MIHF
+---------------------+--------------------------------------------+
| Messages (Command) | Description |
+---------------------+--------------------------------------------+
| MIH_Link_Get | Get the status of a link |
| _Parameters | |
+---------------------+--------------------------------------------+
| MIH_Net_HO | Network initiates handover and sends a list|
| _Candidate _Query | of suggested networks and associated points|
| | of attachment |
+---------------------+--------------------------------------------+
| MIH_Link_Configure | Configure link parameter thresholds |
| Thresholds | |
+---------------------+--------------------------------------------+
| MIH_Link_Actions | Control the behavior of a set of links |
+---------------------+--------------------------------------------+
| MIH_MN_HO_ | Command used by MN to query and obtain |
| _Candidate Query | handover related information about possible|
| | candidate networks |
+---------------------+--------------------------------------------+
| MIH_N2N_HO_Query | command sent by the serving MIHF entity to |
| _Resources | the target MIHF entity for resource query |
Zhang, et al Expires May 15, 2019 [Page 14]
Internet-Draft MIF API extension Nov 2018
+---------------------+--------------------------------------------+
| MIH_MN_HO_Commit | Command used by MN to notify the serving |
| | network of the decided target network |
| | information |
+---------------------+--------------------------------------------+
| MIH_Net_HO_Commit | Command used by the network to notify the |
| | MN of the decided target network informatio|
+---------------------+--------------------------------------------+
| MIH_N2N_HO_Commit | Command used by a serving network to inform|
| | a target network that an MN is about to |
| | move toward that network, initiate context |
| | transfer and perform handover preparation |
+---------------------+--------------------------------------------+
| MIH_MN_HO_Complete | Notification from MIHF of the MN to the |
| | target or source MIHF indicating the |
| | status of handover completion |
+---------------------+--------------------------------------------+
| MIH_N2N_HO_ | Notification from MIHF of the MN to the |
| Complete | target or source MIHF indicating the |
| | status of handover completion |
+---------------------+--------------------------------------------+
| MIH_N2N_HO | Notification from either source or target |
| Complete | MIHF to the peer MIHF indicating the status|
| | of the handover completion |
+---------------------+--------------------------------------------+
Table 3 Command Messages of MIHF
+---------------------+-------------------------------------------+
| Messages | Description |
|(Service management) | |
+---------------------+-------------------------------------------+
| MIH_Capability | Discover list of Events and Commands |
| _Discover | supported by MIHF |
+---------------------+-------------------------------------------+
| MIH_Register | Register with a remote MIHF |
+---------------------+-------------------------------------------+
| MIH_DeRegister | Deregister with a remote MIHF |
+---------------------+-------------------------------------------+
| MIH_Event_Subscribe | Subscribe for MIH event notification |
+---------------------+-------------------------------------------+
|MIH_Event_Unsubscibe | Unsubscribe from MIH event notification |
+---------------------+-------------------------------------------+
Table 4 Service Management of MIHF
Zhang, et al Expires May 15, 2019 [Page 15]
Internet-Draft MIF API extension Nov 2018
7. Security Considerations
This document does not contain any security considerations.
8. IANA Considerations
There are presently no IANA considerations with this document.
9. References
9.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
9.2. Informative References
[IEEE 802.21] IEEE, "IEEE Standard for Local and Metropolitan Area
Networks Part 21: Media Independent Handover Services",
IEEE LAN/MAN Std 802.21-2008, January 2009.
<http://www.ieee802.org/21/private/Published%20Spec/802.21
-2008.pdf>.
[I-D.ietf-mif-api-extension] Liu, D., Lemon, T., Ismailov, Y., and
Z.Cao, "MIF API consideration", draft-ietf-mif-api-
extension-05 (work in progress), Feb. 2014.
10. Acknowledgments
This document was prepared using 2-Word-v2.0.template.dot.
Zhang, et al Expires May 15, 2019 [Page 16]
Internet-Draft MIF API extension Nov 2018
Authors' Addresses
Hongke Zhang
Beijing Jiaotong University (BJTU)
Beijing, 100044, P.R.China
Email: hkzhang@bjty.edu.cn
Fei Song
Beijing Jiaotong University (BJTU)
Beijing, 100044, P.R.China
Email: fsong@bjtu.edu.cn
Boxin Du
Beijing Jiaotong University (BJTU)
Beijing, 100044, P.R.China
Email: 10291070@bjtu.edu.cn
Mi Zhang
Beijing Jiaotong University (BJTU)
Beijing, 100044, P.R.China
Email: 13120174@bjtu.edu.cn
Zhang, et al Expires May 15, 2019 [Page 17]