Network Working Group                                 P. Ford-Hutchinson
Request for Comments: 4217                                    IBM UK Ltd
Category: Standards Track                                   October 2005


                         Securing FTP with TLS

Status of This Memo

   This document specifies an Internet standards track protocol for the
   Internet community, and requests discussion and suggestions for
   improvements.  Please refer to the current edition of the "Internet
   Official Protocol Standards" (STD 1) for the standardization state
   and status of this protocol.  Distribution of this memo is unlimited.

Copyright Notice

   Copyright (C) The Internet Society (2005).

Abstract

   This document describes a mechanism that can be used by FTP clients
   and servers to implement security and authentication using the TLS
   protocol defined by RFC 2246, "The TLS Protocol Version 1.0.", and
   the extensions to the FTP protocol defined by RFC 2228, "FTP Security
   Extensions".  It describes the subset of the extensions that are
   required and the parameters to be used, discusses some of the policy
   issues that clients and servers will need to take, considers some of
   the implications of those policies, and discusses some expected
   behaviours of implementations to allow interoperation.  This document
   is intended to provide TLS support for FTP in a similar way to that
   provided for SMTP in RFC 2487, "SMTP Service Extension for Secure
   SMTP over Transport Layer Security", and HTTP in RFC 2817, "Upgrading
   to TLS Within HTTP/1.1.".

   This specification is in accordance with RFC 959, "File Transfer
   Protocol".  It relies on RFC 2246, "The TLS Protocol Version 1.0.",
   and RFC 2228, "FTP Security Extensions".













Ford-Hutchinson             Standards Track                     [Page 1]


RFC 4217                 Securing FTP with TLS              October 2005


Table of Contents

   1. Introduction ....................................................3
   2. Audience ........................................................5
   3. Overview ........................................................5
   4. Session Negotiation on the Control Port .........................5
      4.1. Client Wants a Secured Session .............................5
      4.2. Server Wants a Secured Session .............................6
   5. Clearing the Control Port .......................................6
   6. Response to the FEAT Command ....................................7
   7. Data Connection Behaviour .......................................8
   8. Mechanisms for the AUTH Command .................................9
   9. Data Connection Security ........................................9
   10. A Discussion of Negotiation Behaviour .........................11
      10.1. The Server's View of the Control Connection ..............11
      10.2. The Server's View of the Data Connection .................12
      10.3. The Client's View of the Control Connection ..............14
      10.4. The Client's View of the Data Connection .................15
   11. Who Negotiates What, Where, and How ...........................15
      11.1. Do we protect at all? ....................................15
      11.2. What level of protection do we use on the Control
            connection? ..............................................15
      11.3. Do we protect data connections in general? ...............16
      11.4. Is protection required for a particular data transfer? ...16
      11.5. What level of protection is required for a
            particular data ..........................................16
   12. Timing Diagrams ...............................................16
      12.1. Establishing a Protected Session .........................17
      12.2. Establishing a Protected Session Without a
            Password Request .........................................18
      12.3. Establishing a Protected Session and then
            Clearing with the CCC ....................................19
      12.4. A Standard Data Transfer Without Protection ..............20
      12.5. A Firewall-Friendly Data Transfer Without Protection .....20
      12.6. A Standard Data Transfer with Protection .................21
      12.7. A Firewall-Friendly Data Transfer with Protection ........21
   13. Discussion of the REIN Command ................................22
   14. Discussion of the STAT and ABOR Commands ......................22
   15. Security Considerations .......................................23
      15.1. Verification of Authentication Tokens ....................23
           15.1.1. Server Certificates ...............................23
           15.1.2. Client Certificates ...............................23
      15.2. Addressing FTP Security Considerations [RFC-2577] ........24
           15.2.1. Bounce Attack .....................................24
           15.2.2. Restricting Access ................................24
           15.2.3. Protecting Passwords ..............................24
           15.2.4. Privacy ...........................................24
           15.2.5. Protecting Usernames ..............................24



Ford-Hutchinson             Standards Track                     [Page 2]


RFC 4217                 Securing FTP with TLS              October 2005


           15.2.6. Port Stealing .....................................25
           15.2.7. Software-Based Security Problems ..................25
      15.3. Issues with the CCC Command ..............................25
   16. IANA Considerations ...........................................25
   17. Other Parameters ..............................................25
   18. Scalability and Limits ........................................26
   19. Applicability .................................................26
   20. Acknowledgements ..............................................26
   21. References ....................................................26
      21.1. Normative References .....................................26
      21.2. Informative References ...................................27

1.  Introduction

   This document describes how three other documents should be combined
   to provide a useful, interoperable, and secure file transfer
   protocol.  Those documents are:

      RFC 959 [RFC-959]

         The description of the Internet File Transfer Protocol.

      RFC 2246 [RFC-2246]

         The description of the Transport Layer Security protocol
         (developed from the Netscape Secure Sockets Layer (SSL)
         protocol version 3.0).

      RFC 2228 [RFC-2228]

         Extensions to the FTP protocol to allow negotiation of security
         mechanisms to allow authentication, confidentiality, and
         message integrity.

   This document is intended to provide TLS support for FTP in a similar
   way to that provided for SMTP in RFC 3207 [RFC-3207] and HTTP in RFC
   2817 [RFC-2817].

   The security extensions to FTP in [RFC-2228] offer a comprehensive
   set of commands and responses that can be used to add authentication,
   integrity, and confidentiality to the FTP protocol.  The TLS protocol
   is a popular (due to its wholesale adoption in the HTTP environment)
   mechanism for generally securing a socket connection.

   Although TLS is not the only mechanism for securing file transfer, it
   does offer some of the following positive attributes:





Ford-Hutchinson             Standards Track                     [Page 3]


RFC 4217                 Securing FTP with TLS              October 2005


      - Flexible security levels.  TLS can support confidentiality,
        integrity, authentication, or some combination of all of these.
        During a session, this allows clients and servers to dynamically
        decide on the level of security required for a particular data
        transfer.

      - Ability to provide strong authentication of the FTP server.

      - It is possible to use TLS identities to authenticate client
        users and client hosts.

      - Formalised public key management.  By use of well established
        client identity mechanisms (supported by TLS) during the
        authentication phase, certificate management may be built into a
        central function.  Whilst this may not be desirable for all uses
        of secured file transfer, it offers advantages in certain
        structured environments.

      - Co-existence and interoperation with authentication mechanisms
        that are already in place for the HTTPS protocol.  This allows
        web browsers to incorporate secure file transfer using the same
        infrastructure that has been set up to allow secure web
        browsing.

   The TLS protocol is a development of the Netscape Communication
   Corporation's SSL protocol and this document can be used to allow the
   FTP protocol to be used with either SSL or TLS.  The actual protocol
   used will be decided by the negotiation of the protected session by
   the TLS/SSL layer.  This document will only refer to the TLS
   protocol; however, it is understood that the Client and Server MAY
   actually be using SSL if they are so configured.

   There are many ways in which these three protocols can be combined.
   This document selects one method by which FTP can operate securely,
   while providing both flexibility and interoperation.  This
   necessitates a brief description of the actual negotiation mechanism,
   a detailed description of the required policies and practices, and a
   discussion of the expected behaviours of clients and servers to allow
   either party to impose their security requirements on the FTP
   session.

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY" and "OPTIONAL" that
   appear in this document are to be interpreted as described in
   [RFC-2119].






Ford-Hutchinson             Standards Track                     [Page 4]


RFC 4217                 Securing FTP with TLS              October 2005


2.  Audience

   This document is aimed at developers who wish to implement TLS as a
   security mechanism to secure FTP clients and/or servers.

   Systems administrators and architects should be fully aware of the
   security implications discussed in [RFC-2228], which need to be
   considered when choosing an implementation of this protocol and
   configuring it to provide their required security.

3.  Overview

   A full description of the FTP security protocol enhancements is
   contained in [RFC-2228].  This document describes how the AUTH, PROT,
   PBSZ, and CCC commands, defined therein, should be implemented with
   the TLS protocol.

   In summary, an FTP session is established on the normal control port.
   A client requests TLS with the AUTH command and then decides if it
   wishes to secure the data connections by use of the PBSZ and PROT
   commands.  Should a client wish to make the control connection revert
   back into plaintext (for example, once the authentication phase is
   completed), then the CCC command can be used.

   Implementation of this protocol extension does not ensure that each
   and every session and data transfer is secure, it merely provides the
   tools that allow a client and/or server to negotiate an acceptable or
   required level of security for that given session or data transfer.
   However, it is possible to have a server implementation that is
   capable of refusing to operate in an insecure fashion.

4.  Session Negotiation on the Control Port

   The server listens on the normal FTP control port {FTP-PORT} and the
   session initiation is not secured at all.  Once the client wishes to
   secure the session, the AUTH command is sent and the server MAY then
   allow TLS negotiation to take place.

4.1.  Client Wants a Secured Session

   If a client wishes to attempt to secure a session, then it SHOULD, in
   accordance with [RFC-2228], send the AUTH command with the parameter
   requesting TLS {TLS-PARM} ('TLS').

   The client then needs to behave according to its policies depending
   on the response received from the server and also the result of the
   TLS negotiation.  A client that receives an AUTH rejection MAY choose
   to continue with the session unprotected if it so desires.



Ford-Hutchinson             Standards Track                     [Page 5]


RFC 4217                 Securing FTP with TLS              October 2005


4.2.  Server Wants a Secured Session

   The FTP protocol does not allow a server to directly dictate client
   behaviour; however, the same effect can be achieved by refusing to
   accept certain FTP commands until the session is secured to a level
   that is acceptable to the server.

   In either case, '234' is the server response to an 'AUTH TLS' command
   that it will honour.

   The '334' response, as defined in [RFC-2228], implies that an ADAT
   exchange will follow.  This document does not use the ADAT command
   and so the '334' reply is incorrect.

   The FTP protocol insists that a USER command be used to identify the
   entity attempting to use the ftp server.  Although the TLS
   negotiation may be providing authentication information, the USER
   command MUST still be issued by the client.  However, it will be a
   server implementation issue to decide which credentials to accept and
   what consistency checks to make between the client cert used and the
   parameter on the USER command.

   [RFC-2228] states that the user must reauthorize (that is, reissue
   some or all of the USER, PASS, and ACCT commands) following an AUTH
   command.  Additionally, this document specifies that all other
   transfer parameters (other than the AUTH parameter) must be reset,
   almost as if a REIN command was issued.

      Reset transfer parameters after the AUTH command, including (but
      are not limited to): user identity, default data ports, TYPE,
      STRU, MODE, and current working directory.

5.  Clearing the Control Port

   There are circumstances in which it may be desirable to protect the
   control connection only during part of the session and then to revert
   back to a plaintext connection.  This is often due to the limitations
   of boundary devices such as NAT and firewalls, which expect to be
   able to examine the content of the control connection in order to
   modify their behaviour.

   Typically the AUTH, USER, PASS, PBSZ, and PROT commands would be
   protected within the TLS protocol and then the CCC command would be
   issued to return to a plaintext socket state.  This has important
   Security Issues (which are discussed in the Security Considerations
   section), but this document describes how the command should be used,
   if the client and server still wish to use it after having considered
   the issues.



Ford-Hutchinson             Standards Track                     [Page 6]


RFC 4217                 Securing FTP with TLS              October 2005


   When a server receives the CCC command, it should behave as follows:

      If the server does not accept CCC commands (or does not understand
      them), then a 500 reply should be sent.

      Otherwise, if the control connection is not protected with TLS,
      then a 533 reply should be sent.

      Otherwise, if the server does not wish to allow the control
      connection to be cleared at this time, then a 534 reply should be
      sent.

      Otherwise, the server is accepting the CCC command and should do
      the following:

         o  Send a 200 reply.

         o  Shutdown the TLS session on the socket and leave it open.

         o  Continue the control connection in plaintext, expecting the
            next command from the client to be in plaintext.

         o  Not accept any more PBSZ or PROT commands.  All subsequent
            data transfers must be protected with the current PROT
            settings.

6.  Response to the FEAT Command

   The FEAT command (introduced in [RFC-2389]) allows servers with
   additional features to advertise these to a client by responding to
   the FEAT command.  If a server supports the FEAT command, then it
   MUST advertise supported AUTH, PBSZ, and PROT commands in the reply,
   as described in section 3.2 of [RFC-2389].  Additionally, the AUTH
   command should have a reply that identifies 'TLS' as one of the
   possible parameters to AUTH.  It is not necessary to identify the
   'TLS-C' synonym separately.

   Example reply (in the same style as [RFC-2389])

      C> FEAT
      S> 211-Extensions supported
      S>  AUTH TLS
      S>  PBSZ
      S>  PROT
      S> 211 END






Ford-Hutchinson             Standards Track                     [Page 7]


RFC 4217                 Securing FTP with TLS              October 2005


7.  Data Connection Behaviour

   The Data Connection in the FTP model can be used in one of three
   ways.  (Note: These descriptions are not necessarily placed in exact
   chronological order, but do describe the steps required.  See
   diagrams later for clarification.)

            i) Classic FTP client/server data exchange

                 - The client obtains a port; sends the port number to
                   the server; the server connects to the client.  The
                   client issues a send or receive request to the server
                   on the control connection and the data transfer
                   commences on the data connection.

          ii) Firewall-Friendly client/server data exchange (as
              discussed in [RFC-1579]) using the PASV command to reverse
              the direction of the data connection.

                 - The client requests that the server open a port; the
                   server obtains a port and returns the address and
                   port number to the client; the client connects to the
                   server on this port.  The client issues a send or
                   receive request on the control connection, and the
                   data transfer commences on the data connection.

         iii) Client-initiated server/server data exchange (proxy or
              PASV connections).

                 - The client requests that server A opens a port;
                   server A obtains a port and returns it to the client;
                   the client sends this port number to server B.
                   Server B connects to server A.  The client sends a
                   send or receive request to server A and the
                   complement to server B and the data transfer
                   commences.  In this model, server A is the proxy or
                   PASV host and is a client for the Data Connection to
                   server B.

   For i) and ii), the FTP client MUST be the TLS client and the FTP
   server MUST be the TLS server.

   That is to say, it does not matter which side initiates the
   connection with a connect() call or which side reacts to the
   connection via the accept() call; the FTP client, as defined in
   [RFC-959], is always the TLS client, as defined in [RFC-2246].





Ford-Hutchinson             Standards Track                     [Page 8]


RFC 4217                 Securing FTP with TLS              October 2005


   In scenario iii), there is a problem in that neither server A nor
   server B is the TLS client, given the fact that an FTP server must
   act as a TLS server for Firewall-Friendly FTP [RFC-1579].  Thus, this
   is explicitly excluded in the security extensions document [RFC-2228]
   and in this document.

8.  Mechanisms for the AUTH Command

   The AUTH command takes a single parameter to define the security
   mechanism to be negotiated.  As the SSL/TLS protocols self-negotiate
   their levels, there is no need to distinguish between SSL and TLS in
   the application layer.  The mechanism name for negotiating TLS is the
   character string identified in {TLS-PARM}.  This allows the client
   and server to negotiate TLS on the control connection without
   altering the protection of the data channel.  To protect the data
   channel as well, the PBSZ command, followed by the PROT command
   sequence, MUST be used.

   Note: The data connection state MAY be modified by the client issuing
   the PROT command with the new desired level of data channel
   protection and the server replying in the affirmative.  This data
   channel protection negotiation can happen at any point in the session
   (even straight after a PORT or PASV command) and as often as is
   required.

   See also Section 16, "IANA Considerations".

9.  Data Connection Security

   The Data Connection security level is determined by the PROT command.

      The PROT command, as specified in [RFC-2228], allows client/server
      negotiation of the security level of the data connection.  Once a
      PROT command has been issued by the client and accepted by the
      server returning the '200' reply, the security of subsequent data
      connections MUST be at that level until another PROT command is
      issued and accepted; the session ends and a REIN command is
      issued, or the security of the session (via an AUTH command) is
      re-negotiated.

   Data Connection Security Negotiation (the PROT command)

      Note: In line with [RFC-2228], there is no facility for securing
      the Data connection with an insecure Control connection.
      Specifically, the PROT command MUST be preceded by a PBSZ command,
      and a PBSZ command MUST be preceded by a successful security data
      exchange (the TLS negotiation in this case).




Ford-Hutchinson             Standards Track                     [Page 9]


RFC 4217                 Securing FTP with TLS              October 2005


      The command defined in [RFC-2228] to negotiate data connection
      security is the PROT command.  As defined, there are four values
      that the PROT command parameter can take.

            'C' - Clear - neither Integrity nor Privacy

            'S' - Safe - Integrity without Privacy

            'E' - Confidential - Privacy without Integrity

            'P' - Private - Integrity and Privacy

      As TLS negotiation encompasses (and exceeds) the Safe /
      Confidential / Private distinction, only Private (use TLS) and
      Clear (don't use TLS) are used.

      For TLS, the data connection can have one of two security levels.

            1) Clear (requested by 'PROT C')

            2) Private (requested by 'PROT P')

      With 'Clear' protection level, the data connection is made without
      TLS.  Thus, the connection is unauthenticated and has no
      confidentiality or integrity.  This might be the desired behaviour
      for servers sending file lists, pre-encrypted data, or non-
      sensitive data (e.g., for anonymous FTP servers).

      If the data connection security level is 'Private', then a TLS
      negotiation must take place on the data connection to the
      satisfaction of the Client and Server prior to any data being
      transmitted over the connection.  The TLS layers of the Client and
      Server will be responsible for negotiating the exact TLS Cipher
      Suites that will be used (and thus the eventual security of the
      connection).

      In addition, the PBSZ (protection buffer size) command, as
      detailed in [RFC-2228], is compulsory prior to any PROT command.
      This document also defines a data channel encapsulation mechanism
      for protected data buffers.  For FTP-TLS, which appears to the FTP
      application as a streaming protection mechanism, this is not
      required.  Thus, the PBSZ command MUST still be issued, but must
      have a parameter of '0' to indicate that no buffering is taking
      place and the data connection should not be encapsulated.

      Note that PBSZ 0 is not in the grammar of [RFC-2228], section 8.1,
      where it is stated:




Ford-Hutchinson             Standards Track                    [Page 10]


RFC 4217                 Securing FTP with TLS              October 2005


         PBSZ <sp> <decimal-integer> <CRLF> <decimal-integer> ::= any
         decimal integer from 1 to (2^32)-1

      However, it should be noted that using a value of '0' to mean a
      streaming protocol is a reasonable use of '0' for that parameter
      and is not ambiguous.

   Initial Data Connection Security

      The initial state of the data connection MUST be 'Clear' (this is
      the behaviour as indicated by [RFC-2228]).

10.  A Discussion of Negotiation Behaviour

   As [RFC-2228] allows security qualities to be negotiated, enabled,
   and disabled dynamically, this can make implementations seem quite
   complex.  However, in any given instance the behaviour should be
   quite straightforward.  Either the server will be enforcing the
   policy of the server host or it will be providing security
   capabilities requested by the client.  Either the client will be
   conforming to the server's policy or will be endeavouring to provide
   the capabilities that the user desires.

10.1.  The Server's View of the Control Connection

   A server MAY have a policy statement somewhere that might:

      - Deny any command before TLS is negotiated (this might cause
        problems if a SITE or some such command is required prior to
        login).

      - Deny certain commands before TLS is negotiated (e.g., USER,
        PASS, or ACCT).

      - Deny insecure USER commands for certain users (e.g., not
        ftp/anonymous).

      - Deny secure USER commands for certain users (e.g.,
        ftp/anonymous).

      - Define the level(s) of TLS to be allowed.

      - Define the CipherSuites allowed to be used (perhaps on a per
        host/domain/...  basis).

      - Allow TLS authentication as a substitute for local
        authentication.




Ford-Hutchinson             Standards Track                    [Page 11]


RFC 4217                 Securing FTP with TLS              October 2005


      - Define data connection policies (see next section).

      It is possible that the TLS negotiation may not be completed
      satisfactorily for the server, in which case it can be one of
      these states.

         The TLS negotiation failed completely

            In this case, the control connection should still be in an
            unprotected mode and the server SHOULD issue an unprotected
            '421' reply to end the session.

         The TLS negotiation completed successfully, but the server
         decides that the session parameters are not acceptable (e.g.,
         Distinguished Name in the client certificate is not permitted
         to use the server).

            In this case, the control connection should still be in a
            protected state, so the server MAY either continue to refuse
            to service commands or issue a protected '421' reply and
            close the connection.

         The TLS negotiation failed during the TLS handshake

            In this case, the control connection is in an unknown state
            and the server SHOULD simply drop the control connection.

   The server code will be responsible for implementing the required
   policies and ensuring that the client is prevented from circumventing
   the chosen security by refusing to service those commands that are
   against policy.

10.2.  The Server's View of the Data Connection

   The server can take one of four basic views of the data connection.

      1 - Don't allow encryption at all (in which case the PROT command
          should not allow any value other than 'C' - if it is allowed
          at all).

      2 - Allow the client to choose protection or not.

      3 - Insist on data protection (in which case the PROT command must
          be issued prior to the first attempted data transfer).

      4 - Decide on one of the above three for each and every data
          connection.




Ford-Hutchinson             Standards Track                    [Page 12]


RFC 4217                 Securing FTP with TLS              October 2005


   The server SHOULD only check the status of the data protection level
   (for options 3 and 4 above) on the actual command that will initiate
   the data transfer (and not on the PORT or PASV).  The following
   commands, defined in [RFC-959], cause data connections to be opened
   and thus may be rejected before any 1xx message due to an incorrect
   PROT setting.

         STOR
         RETR
         NLST
         LIST
         STOU
         APPE

   The reply to indicate that the PROT setting is incorrect is '521 data
   connection cannot be opened with this PROT setting'

   If the protection level indicates that TLS is required, then it
   should be negotiated once the data connection is made.  Thus, the
   '150' reply only states that the command can be used given the
   current PROT level.  Should the server not like the TLS negotiation,
   then it will close the data port immediately and follow the '150'
   command with a '522' reply, which indicates that the TLS negotiation
   failed or was unacceptable.  (Note: This means that the application
   can pass a standard list of CipherSuites to the TLS layer for
   negotiation, and review the one negotiated for applicability in each
   instance).

   The Security Considerations section discusses the issue of cross-
   checking any certificates used to authenticate the data connection
   with the one(s) used to authenticate the control connection.  This is
   an important security step.

   It is reasonable for the server to insist that the data connection
   uses a TLS cached session.  This might be a cache of a previous data
   connection or of a cleared control connection.  If this is the reason
   for the refusal to allow the data transfer, then the '522' reply
   should indicate this.

   Note: This has an important impact on client design, but allows
   servers to minimise the cycles used during TLS negotiation by
   refusing to perform a full negotiation with a previously
   authenticated client.

   It should be noted that the TLS authentication of the server will be
   authentication of the server host itself and not a user on the server
   host.




Ford-Hutchinson             Standards Track                    [Page 13]


RFC 4217                 Securing FTP with TLS              October 2005


10.3.  The Client's View of the Control Connection

   In most cases, it is likely that the client will be using TLS because
   the server would refuse to interact insecurely.  To allow for this,
   clients SHOULD be flexible enough to manage the securing of a session
   at the appropriate time and still allow the user/server policies to
   dictate exactly when during the session the security is negotiated.

   In the case where it is the client that is insisting on the securing
   of the session, the client will need to ensure that the negotiations
   are all completed satisfactorily and will need to be able to sensibly
   inform the user should the server not support, or not be prepared to
   use, the required security levels.

   Clients SHOULD be coded in such a manner as to allow the timing of
   the AUTH, PBSZ, and PROT commands to be flexible and dictated by the
   server.  It is quite reasonable for a server to refuse certain
   commands prior to these commands.  Similarly, it is quite possible
   that a SITE or quoted command might be needed by a server prior to
   the AUTH.  A client MUST allow a user to override the timing of these
   commands to suit a specific server.

   For example, a client SHOULD NOT insist on sending the AUTH as the
   first command in a session, nor should it insist on issuing a
   PBSZ/PROT pair directly after the AUTH.  This may well be the default
   behaviour, but must be overridable by a user.

   The TLS negotiation may not be completed satisfactorily for the
   client, in which case it will be in one of these states:

      The TLS negotiation failed completely

         In this case, the control connection should still be in an
         unprotected mode and the client should issue an unprotected
         QUIT command to end the session.

      The TLS negotiation completed successfully, but the client decides
      that the session parameters are not acceptable (e.g.,
      Distinguished Name in certificate is not the actual server
      expected).

         In this case, the control connection should still be up in a
         protected state, so the client should issue a protected QUIT
         command to end the session.







Ford-Hutchinson             Standards Track                    [Page 14]


RFC 4217                 Securing FTP with TLS              October 2005


      The TLS negotiation failed during the TLS handshake.

         In this case, the control connection is in an unknown state and
         the client should simply drop the control connection.

10.4.  The Client's View of the Data Connection

   Client security policies

      Clients do not typically have 'policies' as such, instead they
      rely on the user to define their actions and, to a certain extent,
      are reactive to the server policy.  Thus, a client will need to
      have commands that will allow the user to switch the protection
      level of the data connection dynamically; however, there may be a
      general 'policy' that attempts all LIST and NLST commands on a
      Clear connection first (and automatically switches to Private if
      it fails).  In this case, there would need to be a user command
      available to ensure that a given data transfer was not attempted
      on an insecure data connection.

      Clients also need to understand that the level of the PROT setting
      is only checked for a particular data transfer after that transfer
      has been requested.  Thus, a refusal by the server to accept a
      particular data transfer should not be read by the client as a
      refusal to accept that data protection level completely, as not
      only may other data transfers be acceptable at that protection
      level, but it is entirely possible that the same transfer may be
      accepted at the same protection level at a later point in the
      session.

      It should be noted that the TLS authentication of the client
      should be an authentication of a user on the client host and not
      the client host itself.

11.  Who Negotiates What, Where, and How

11.1.  Do we protect at all?

   Client issues 'AUTH TLS', server accepts or rejects.  If the server
   needs AUTH, then it refuses to accept certain commands until it gets
   a successfully protected session.

11.2.  What level of protection do we use on the Control connection?

   Decided entirely by the TLS CipherSuite negotiation.






Ford-Hutchinson             Standards Track                    [Page 15]


RFC 4217                 Securing FTP with TLS              October 2005


11.3.  Do we protect data connections in general?

   Client issues PROT command, server accepts or rejects.

11.4.  Is protection required for a particular data transfer?

   A client would have already issued a PROT command if it required the
   connection to be protected.

   If a server needs to have the connection protected, then it will
   reply to the STOR/RETR/NLST/... command with a '522', indicating that
   the current state of the data connection protection level is not
   sufficient for that data transfer at that time.

11.5.  What level of protection is required for a particular data
       transfer?

   Decided entirely by the TLS CipherSuite negotiation.

   Thus, for flexibility, it can be seen that it is desirable for the
   FTP application to be able to interact with the TLS layer upon which
   it sits to define and discover the exact TLS CipherSuites that are to
   be/have been negotiated and to make decisions accordingly.

12.  Timing Diagrams

   These timing diagrams aim to help explain exactly how the TLS
   handshake and session protection fits into the existing logic of the
   FTP protocol.  Of course, the FTP protocol itself is not well
   described with respect to the timing of commands and responses in
   [RFC-959], so this is partly based on empirical observation of
   existing widespread client and server implementations.



















Ford-Hutchinson             Standards Track                    [Page 16]


RFC 4217                 Securing FTP with TLS              October 2005


12.1.  Establishing a Protected Session

              Client                                 Server
     control          data                   data               control
   ====================================================================

                                                                socket()
                                                                bind()
     socket()
     connect()  ----------------------------------------------> accept()
               <----------------------------------------------  220
     AUTH TLS   ---------------------------------------------->
               <----------------------------------------------  234
     TLSneg()  <----------------------------------------------> TLSneg()
     PBSZ 0     ---------------------------------------------->
               <----------------------------------------------  200
     PROT P     ---------------------------------------------->
               <----------------------------------------------  200
     USER fred  ---------------------------------------------->
               <----------------------------------------------  331
     PASS pass  ---------------------------------------------->
               <----------------------------------------------  230

   Note 1: The order of the PBSZ/PROT pair and the USER/PASS pair (with
   respect to each other) is not important (i.e., the USER/PASS can
   happen prior to the PBSZ/PROT, or the server can refuse to allow a
   PBSZ/PROT pair until the USER/PASS pair has happened).

   Note 2: The PASS command might not be required at all (if the USER
   parameter and any client identity presented provide sufficient
   authentication).  The server would indicate this by issuing a '232'
   reply to the USER command instead of the '331', which requests a PASS
   from the client (see below).

   Note 3: The AUTH command might not be the first command after the
   receipt of the 220 welcome message.















Ford-Hutchinson             Standards Track                    [Page 17]


RFC 4217                 Securing FTP with TLS              October 2005


12.2.  Establishing a Protected Session Without a Password Request
       (The TLS Authentication is Sufficient)

              Client                                 Server
     control          data                   data               control
   ====================================================================

                                                                socket()
                                                                bind()
     socket()
     connect()  ----------------------------------------------> accept()
               <----------------------------------------------  220
     AUTH TLS   ---------------------------------------------->
               <----------------------------------------------  234
     TLSneg()  <----------------------------------------------> TLSneg()
     PBSZ 0     ---------------------------------------------->
               <----------------------------------------------  200
     PROT P     ---------------------------------------------->
               <----------------------------------------------  200
     USER fred  ---------------------------------------------->
               <----------------------------------------------  232






























Ford-Hutchinson             Standards Track                    [Page 18]


RFC 4217                 Securing FTP with TLS              October 2005


12.3.  Establishing a Protected Session and then Clearing with the CCC
       Command

             Client                                 Server
    control          data                   data               control
  ====================================================================

                                                               socket()
                                                               bind()
    socket()
    connect()  ----------------------------------------------> accept()
              <----------------------------------------------  220
    AUTH TLS   ---------------------------------------------->
              <----------------------------------------------  234
    TLSneg()  <----------------------------------------------> TLSneg()
    PBSZ 0     ---------------------------------------------->
              <----------------------------------------------  200
    PROT P     ---------------------------------------------->
              <----------------------------------------------  200
    USER fred  ---------------------------------------------->
              <----------------------------------------------  232
    CCC        ---------------------------------------------->
              <----------------------------------------------  200
    TLSshutdown()  <-------------------------------------> TLSshutdown()

   - The rest of the control session continues in plaintext with
     protected data transfers (due to PROT P).

   Note: This has serious security issues (see Security Considerations
   section) but may be useful in a firewall/NAT scenario.





















Ford-Hutchinson             Standards Track                    [Page 19]


RFC 4217                 Securing FTP with TLS              October 2005


12.4.  A Standard Data Transfer Without Protection

              Client                                 Server
     control          data                   data               control
   ====================================================================

                      socket()
                      bind()
     PORT w,x,y,z,a,b ----------------------------------------->
         <----------------------------------------------------- 200
     STOR file ------------------------------------------------>
                                             socket()
                                             bind()
         <----------------------------------------------------- 150
                      accept() <-----------  connect()
                      write()   -----------> read()
                      close()   -----------> close()
         <----------------------------------------------------- 226

12.5.  A Firewall-Friendly Data Transfer Without Protection

              Client                                 Server
     control          data                   data               control
   ====================================================================

     PASV -------------------------------------------------------->
                                             socket()
                                             bind()
         <------------------------------------------ 227 (w,x,y,z,a,b)
                      socket()
     STOR file --------------------------------------------------->
                      connect()  ----------> accept()
         <-------------------------------------------------------- 150
                      write()    ----------> read()
                      close()    ----------> close()
         <-------------------------------------------------------- 226

   Note: Implementers should be aware that the connect()/accept()
   function is performed prior to the receipt of the reply from the STOR
   command.  This contrasts the with situation when a non-firewall-
   friendly PORT is used prior to the STOR, and the accept()/connect()
   is performed after the reply from the aforementioned STOR has been
   dealt with.








Ford-Hutchinson             Standards Track                    [Page 20]


RFC 4217                 Securing FTP with TLS              October 2005


12.6.  A Standard Data Transfer with Protection

              Client                                 Server
     control          data                   data               control
   ====================================================================

                      socket()
                      bind()
     PORT w,x,y,z,a,b -------------------------------------------->
         <-------------------------------------------------------- 200
     STOR file --------------------------------------------------->
                                             socket()
                                             bind()
         <-------------------------------------------------------- 150
                      accept()  <----------  connect()
                      TLSneg()  <----------> TLSneg()
                      TLSwrite() ----------> TLSread()
                      TLSshutdown() -------> TLSshutdown()
                      close()    ----------> close()
         <-------------------------------------------------------- 226

12.7.  A Firewall-Friendly Data Transfer with Protection

              Client                                 Server
     control          data                   data               control
   ====================================================================

     PASV -------------------------------------------------------->
                                             socket()
                                             bind()
         <------------------------------------------ 227 (w,x,y,z,a,b)
                      socket()
     STOR file --------------------------------------------------->
                      connect()  ----------> accept()
         <-------------------------------------------------------- 150
                      TLSneg()   <---------> TLSneg()
                      TLSwrite()  ---------> TLSread()
                      TLSshutdown() -------> TLSshutdown()
                      close()     ---------> close()
         <-------------------------------------------------------- 226











Ford-Hutchinson             Standards Track                    [Page 21]


RFC 4217                 Securing FTP with TLS              October 2005


13.  Discussion of the REIN Command

   The REIN command, defined in [RFC-959], allows the user to reset the
   state of the FTP session.  From [RFC-959]:

      REINITIALIZE (REIN)

         This command terminates a USER, flushing all I/O and account
         information, except to allow any transfer in progress to be
         completed.  All parameters are reset to the default settings
         and the control connection is left open.  This is identical to
         the state in which a user finds himself immediately after the
         control connection is opened.  A USER command may be expected
         to follow.

   When this command is processed by the server, the TLS session(s) MUST
   be cleared and the control and data connections revert to
   unprotected, clear communications.  It MAY be acceptable to use
   cached TLS sessions for subsequent connections, however, a server
   MUST NOT mandate this.

   If the REIN command is being used to clear a TLS session, then the
   reply to the REIN command MUST be sent in a protected session prior
   to the session(s) being cleared.

14.  Discussion of the STAT and ABOR Commands

   The ABOR and STAT commands and the use of TCP Urgent Pointers

      [RFC-959] describes the use of Telnet commands (IP and DM) and the
      TCP Urgent pointer to indicate the transmission of commands on the
      control channel during the execution of a data transfer.  FTP uses
      the Telnet Interrupt Process and Data Mark commands in conjunction
      with Urgent data to preface two commands: ABOR (Abort Transfer)
      and STAT (Status request).

      The Urgent Pointer was used because, in a Unix implementation, the
      receipt of a TCP packet marked as Urgent would result in the
      execution of the SIGURG interrupt handler.  This reliance on
      interrupt handlers was necessary on systems that did not implement
      select() or did not support multiple threads.  TLS does not
      support the notion of Urgent data.

      When TLS is implemented as a security method in FTP, the server
      SHOULD NOT rely on the use of SIGURG to process input on the
      control channel during data transfers.  The client MUST send all
      data, including Telnet commands, across the TLS session.




Ford-Hutchinson             Standards Track                    [Page 22]


RFC 4217                 Securing FTP with TLS              October 2005


15.  Security Considerations

   This document discusses how TLS may be used in conjunction with
   [RFC-2228] to provide mechanisms for securing FTP sessions.
   Discussions about security rationale and security properties are
   contained within the [RFC-2228] document and are not repeated here.

15.1.  Verification of Authentication Tokens

   In this section, we assume that X.509 certificates will be used for
   the TLS authentication.  If some other identity token is used (e.g.,
   kerberos tickets - see [RFC-2712]), then similar, mechanism-specific
   considerations will need to be made.

15.1.1.  Server Certificates

   - Although it is entirely an implementation decision, it is
     recommended that certificates used for server authentication of the
     TLS session contain the server identification information in a
     similar manner to those used for http servers (see [RFC-2818]).

   - It is strongly recommended that the certificate used for server
     authentication of Data connections be the same certificate as that
     used for the corresponding Control connection.  If different
     certificates are to be used, there should be some other mechanism
     that the client can use to cross-check the data and control
     connection server identities.

   - If Server Certificates are not used, then many of the security
     benefits will not be realised.  For Example, in an anonymous
     Diffie-Hellman environment, there is no server identity
     authentication, so there is little protection against man-in-the-
     middle attacks.

15.1.2.  Client Certificates

   - Deciding which client certificates to allow and defining which
     fields define what authentication information is entirely a server
     implementation issue.

   - However, it is strongly recommended that the certificate used for
     client authentication of Data connections be the same certificate
     as that used for the corresponding Control connection.  If
     different certificates are to be used, there should be some other
     mechanism that the server can use to cross-check the data and
     control connection client identities.





Ford-Hutchinson             Standards Track                    [Page 23]


RFC 4217                 Securing FTP with TLS              October 2005


   - If Client Certificates are not used, then many of the security
     benefits will not be realised.  For Example, it would still be
     possible for a malicious client to hijack a data connection.

15.2.  Addressing FTP Security Considerations [RFC-2577]

15.2.1.  Bounce Attack

   A bounce attack should be harder in a secured FTP environment
   because:

      - The FTP server that is being used to initiate a false connection
        will always be a 'server' in the TLS context.  Therefore, only
        services that act as 'clients' in the TLS context could be
        vulnerable.  This would be a counter-intuitive way to implement
        TLS on a service.

      - The FTP server would detect that the authentication credentials
        for the data connection are not the same as those for the
        control connection, thus the server policies could be set to
        drop the data connection.

      - Genuine users are less likely to initiate such attacks when the
        authentication is strong, and malicious users are less likely to
        gain access to the FTP server if the authentication is not
        easily subverted (password guessing, network tracing, etc...)

15.2.2.  Restricting Access

   This document presents a strong mechanism for solving the issue
   raised in this section.

15.2.3.  Protecting Passwords

   The twin solutions of strong authentication and data confidentiality
   ensure that this is not an issue when TLS is used to protect the
   control session.

15.2.4.  Privacy

   The TLS protocol ensures data confidentiality by encryption.  Privacy
   (e.g., access to download logs, user profile information, etc...) is
   outside the scope of this document (and [RFC-2577] presumably).

15.2.5.  Protecting Usernames

   This is not an issue when TLS is used as the primary authentication
   mechanism.



Ford-Hutchinson             Standards Track                    [Page 24]


RFC 4217                 Securing FTP with TLS              October 2005


15.2.6.  Port Stealing

   This specification will do little for the Denial of Service element
   of this section; however, strong authentication on the data
   connection will prevent unauthorised connections from retrieving or
   submitting files.  Of course, this is only the case where strong
   client authentication is being used.  If client certificates are not
   used, then port stealing by a rogue client is still a problem.  If no
   strong authentication is in use at all (e.g., anonymous Diffie-
   Hellman), then the port stealing problem will remain.

15.2.7.  Software-Based Security Problems

   Nothing in this specification will affect the discussion in this
   section.

15.3.  Issues with the CCC Command

   Using the CCC command can create security issues.  For a full
   description, see the "CLEAR COMMAND CHANNEL (CCC)" section of
   [RFC-2228].  Clients should not assume that a server will allow the
   CCC command to be processed.

   Server implementations may wish to refuse to process the CCC command
   on a session that has not passed through some form of client
   authentication (e.g., TLS client auth or FTP USER/PASS).  This can
   prevent anonymous clients from repeatedly requesting AUTH TLS
   followed by CCC to tie up resources on the server.

16.  IANA Considerations

   {FTP-PORT} - The port assigned to the FTP control connection is 21.

17.  Other Parameters

   {TLS-PARM} - The parameter for the AUTH command to indicate that TLS
   is required.  To request the TLS protocol in accordance with this
   document, the client MUST use 'TLS'

      To maintain backward compatibility with older versions of this
      document, the server SHOULD accept 'TLS-C' as a synonym for 'TLS'.

      Note: [RFC-2228] states that these parameters are case-
      insensitive.







Ford-Hutchinson             Standards Track                    [Page 25]


RFC 4217                 Securing FTP with TLS              October 2005


18.  Scalability and Limits

   There are no issues other than those concerned with the ability of
   the server to refuse to have a complete TLS negotiation for each and
   every data connection, which will allow servers to retain throughput
   whilst using cycles only when necessary.

19.  Applicability

   This mechanism is generally applicable as a mechanism for securing
   the FTP protocol.  It is unlikely that anonymous FTP clients or
   servers will require such security (although some might like the
   authentication features without the confidentiality).

20.  Acknowledgements

   o  Netscape Communications Corporation for the original SSL protocol.

   o  Eric Young for the SSLeay libraries.

   o  University of California, Berkeley for the original
      implementations of FTP and ftpd, on which the initial
      implementation of these extensions were layered.

   o  IETF CAT working group.

   o  IETF TLS working group.

   o  IETF FTPEXT working group.

   o  Jeff Altman for the ABOR and STAT discussion.

   o  The various people who have help author this document throughout
      its protracted draft stages, namely Martin Carpenter, Eric Murray,
      Tim Hudson, and Volker Wiegand.

21.  References

21.1.  Normative References

   [RFC-959]  Postel, J. and J. Reynolds, "File Transfer Protocol", STD
              9, RFC 959, October 1985.

   [RFC-2119] Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119, March 1997.

   [RFC-2228] Horowitz, M. and S. Lunt, "FTP Security Extensions", RFC
              2228, October 1997.



Ford-Hutchinson             Standards Track                    [Page 26]


RFC 4217                 Securing FTP with TLS              October 2005


   [RFC-2246] Dierks, T. and C. Allen, "The TLS Protocol Version 1.0",
              RFC 2246, January 1999.

   [RFC-2389] Hethmon, P. and R. Elz, "Feature negotiation mechanism for
              the File Transfer Protocol", RFC 2389, August 1998.

21.2.  Informative References

   [RFC-1579] Bellovin, S., "Firewall-Friendly FTP", RFC 1579, February
              1994.

   [RFC-2222] Myers, J., "Simple Authentication and Security Layer
              (SASL)", RFC 2222, October 1997.

   [RFC-2577] Allman, M. and S. Ostermann, "FTP Security
              Considerations", RFC 2577, May 1999.

   [RFC-2712] Medvinsky, A. and M. Hur, "Addition of Kerberos Cipher
              Suites to Transport Layer Security (TLS)", RFC 2712,
              October 1999.

   [RFC-2817] Khare, R. and S. Lawrence, "Upgrading to TLS Within
              HTTP/1.1", RFC 2817, May 2000.

   [RFC-2818] Rescorla, E., "HTTP Over TLS", RFC 2818, May 2000.

   [RFC-3207] Hoffman, P., "SMTP Service Extension for Secure SMTP over
              Transport Layer Security", RFC 3207, February 2002.























Ford-Hutchinson             Standards Track                    [Page 27]


RFC 4217                 Securing FTP with TLS              October 2005


Contributors

   Tim Hudson
   RSA Data Security
   Australia Pty Ltd

   Phone: +61 7 3227 4444
   EMail: tjh@rsasecurity.com.au


   Volker Wiegand
   SuSE Linux

   EMail: wiegand@suse.de


   Martin Carpenter
   Verisign Ltd

   EMail: mcarpenter@verisign.com


   Eric Murray
   Wave Systems Inc.

   EMail: ericm@lne.com

Author's Address

   Paul Ford-Hutchinson
   IBM UK Ltd
   PO Box 31
   Birmingham Road
   Warwick
   United Kingdom

   Phone: +44 1926 462005
   EMail: rfc4217@ford-hutchinson.com













Ford-Hutchinson             Standards Track                    [Page 28]


RFC 4217                 Securing FTP with TLS              October 2005


Full Copyright Statement

   Copyright (C) The Internet Society (2005).

   This document is subject to the rights, licenses and restrictions
   contained in BCP 78, and except as set forth therein, the authors
   retain all their rights.

   This document and the information contained herein are provided on an
   "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
   OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET
   ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED,
   INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE
   INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
   WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Intellectual Property

   The IETF takes no position regarding the validity or scope of any
   Intellectual Property Rights or other rights that might be claimed to
   pertain to the implementation or use of the technology described in
   this document or the extent to which any license under such rights
   might or might not be available; nor does it represent that it has
   made any independent effort to identify any such rights.  Information
   on the procedures with respect to rights in RFC documents can be
   found in BCP 78 and BCP 79.

   Copies of IPR disclosures made to the IETF Secretariat and any
   assurances of licenses to be made available, or the result of an
   attempt made to obtain a general license or permission for the use of
   such proprietary rights by implementers or users of this
   specification can be obtained from the IETF on-line IPR repository at
   http://www.ietf.org/ipr.

   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights that may cover technology that may be required to implement
   this standard.  Please address the information to the IETF at ietf-
   ipr@ietf.org.

Acknowledgement

   Funding for the RFC Editor function is currently provided by the
   Internet Society.







Ford-Hutchinson             Standards Track                    [Page 29]