CCAMP J. Ahlberg
Internet-Draft J-O. Carlson
Intended status: Standards Track H-A. Lund
Expires: November 11, 2016 T. Olausson
Ericsson AB
M. Ye
Huawei Technologies Co.
M. Vaupotic
Aviat Networks
May 10, 2016
Microwave Radio Link YANG Data Models
draft-ahlberg-ccamp-microwave-radio-link-01
Abstract
YANG model for managing microwave radio link functionality.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on November 11, 2016.
Copyright Notice
Copyright (c) 2016 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
Ahlberg, et al. Expires November 11, 2016 [Page 1]
Internet-Draft Microwave RL YANG May 2016
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
1.1. Terminology . . . . . . . . . . . . . . . . . . . . . . . 2
1.2. Tree Diagrams . . . . . . . . . . . . . . . . . . . . . . 3
2. Objectives . . . . . . . . . . . . . . . . . . . . . . . . . 3
3. Microwave Model . . . . . . . . . . . . . . . . . . . . . . . 3
4. Microwave Module . . . . . . . . . . . . . . . . . . . . . . 6
5. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 41
6. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 41
7. Security Considerations . . . . . . . . . . . . . . . . . . . 41
8. References . . . . . . . . . . . . . . . . . . . . . . . . . 41
8.1. Normative References . . . . . . . . . . . . . . . . . . 41
8.2. Informative References . . . . . . . . . . . . . . . . . 42
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 42
1. Introduction
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
This document is being discussed within the microwave community.
This document defines a YANG RFC 6020 [RFC6020] module for managing
the radio link functionality of a microwave node. The YANG module is
augmenting RFC 7223 [RFC7223] in order to model a microwave link and
interface in analogy with most other data links in a router or
switch.
In summary, the YANG module defined in this internet draft is:
microwave-radio-link (should be renamed to something like: if-
microwave-radio-link) - Defines the model for basic configuration of
a microwave radio link.
1.1. Terminology
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
Other definitions to clarify....
Ahlberg, et al. Expires November 11, 2016 [Page 2]
Internet-Draft Microwave RL YANG May 2016
1.2. Tree Diagrams
A simplified graphical representation of the data model is used in
this document. The meaning of the symbols in these diagrams is as
follows:
o Brackets "[" and "]" enclose list keys.
o Abbreviations before data node names: "rw" means configuration
(read-write), and "ro" means state data (read-only).
o Symbols after data node names: "?" means an optional node, "!"
means a presence container, and "*" denotes a list or leaf-list.
o Parentheses enclose choice and case nodes, and case nodes are also
marked with a colon (":").
o Ellipsis ("...") stands for contents of subtrees that are not
shown.
2. Objectives
The aim of of the YANG models contained in this draft is to provide
the model that is required to implement the basic radio link
management of microwave devices.
This model may be augmented by vendor specific YANG modules in order
to manage product specific functionality.
However, the intention is that it should not be necessary to have any
vendor specific extensions to the YANG model defined in this document
to implement standard microwave radio link connectivity.
3. Microwave Model
The microwave radio link model provides the parameters for managing
the radio link part of a microwave node.
The "microwave-radio-link" YANG module has the following structure:
module: microwave-radio-link
+--rw radio-link-protection-pairs
| +--rw radio-link-protection-pair* [name]
| +--rw name string
| +--rw protection-switch-mode? enumeration
| +--rw revertive-preferred-tx? if:interface-ref
| +--rw revertive-wait-to-restore? uint16
| +--rw radio-link-protection-members* if:interface-ref
Ahlberg, et al. Expires November 11, 2016 [Page 3]
Internet-Draft Microwave RL YANG May 2016
+--ro radio-link-protection-pairs-state
| +--ro radio-link-protection-pair* [name]
| +--ro name string
| +--ro protection-status? enumeration
| +--ro actual-wait-to-restore? uint16
+--rw xpic-pairs {xpic}?
| +--rw xpic-pair* [name]
| +--rw name string
| +--rw enabled? boolean
| +--rw xpic-members* if:interface-ref
+--rw mimo-groups {mimo}?
+--rw mimo-group* [name]
+--rw name string
+--rw enabled? boolean
+--rw mimo-members* if:interface-ref
augment /if:interfaces/if:interface:
+--rw id? string
+--rw mode? identityref
+--rw expected-far-end-id? string
+--rw far-end-id-check? boolean
+--rw carrier-terminations* if:interface-ref
+--rw rlp-pairs* -> /radio-link-protection-pairs/radio-link-protection-pair/name
+--rw xpic-pairs* -> /xpic-pairs/xpic-pair/name {xpic}?
+--rw mimo-group? -> /mimo-groups/mimo-group/name {mimo}?
augment /if:interfaces/if:interface:
+--rw carrier-id? string
+--rw tx-admin-status? enumeration
+--rw tx-frequency? uint32
+--rw rx-frequency? uint32
+--rw duplex-distance? uint32
+--rw duplex-config? boolean
+--rw polarization? enumeration
+--rw power-mode? enumeration
+--rw selected-output-power? power
+--rw selected-min-output-power? power
+--rw selected-max-output-power? power
+--rw target-input-power-far-end? power
+--rw reference-sec? identityref
+--rw coding-modulation-mode? enumeration
+--rw selected-cm? identityref
+--rw selected-min-acm? identityref
+--rw selected-max-acm? identityref
+--rw if-loop? boolean
+--rw rf-loop? boolean
+--rw ct-performance-thresholds
+--rw input-power-alarm-threshold? power
+--rw output-power-alarm-threshold? power
+--rw ber-alarm-threshold? enumeration
Ahlberg, et al. Expires November 11, 2016 [Page 4]
Internet-Draft Microwave RL YANG May 2016
+--rw rl-1-threshold-level? power
+--rw rlts-1-15min-set-alarm-threshold? uint16
+--rw rlts-1-15min-reset-alarm-threshold? uint16
+--rw rlts-1-24h-set-alarm-threshold? uint32
+--rw tl-1-threshold-level? power
+--rw tlts-1-15min-set-alarm-threshold? power
+--rw tlts-1-15min-reset-alarm-threshold? power
+--rw tlts-1-24h-set-alarm-threshold? uint32
+--rw es-15min-set-alarm-threshold? uint16
+--rw es-15min-reset-alarm-threshold? uint16
+--rw es-24h-set-alarm-threshold? uint32
+--rw ses-15min-set-alarm-threshold? uint16
+--rw ses-15min-reset-alarm-threshold? uint16
+--rw ses-24h-set-alarm-threshold? uint32
+--rw bbe-15min-set-alarm-threshold? uint32
+--rw bbe-15min-reset-alarm-threshold? uint32
+--rw bbe-24h-set-alarm-threshold? uint32
+--rw acm-15min-set-alarm-threshold? uint16
+--rw acm-15min-reset-alarm-threshold? uint16
+--rw acm-24h-set-alarm-threshold? uint32
augment /if:interfaces-state/if:interface:
+--ro tx-oper-status? enumeration
+--ro actual-ouput-power? power
+--ro actual-input-power? power
+--ro actual-tx-cm? identityref
+--ro actual-rx-cm? identityref
+--ro selected-min-speed? yang:gauge64
+--ro selected-max-speed? yang:gauge64
+--ro xpic-status? enumeration {xpic}?
+--ro mimo-status? enumeration {mimo}?
+--ro actual-snir? decimal64
+--ro actual-xpi? decimal64 {xpic}?
+--ro actual-si? decimal64 {mimo}?
+--ro capabilities
+--ro min-tx-frequency? uint32
+--ro max-tx-frequency? uint32
+--ro min-rx-frequency? uint32
+--ro max-rx-frequency? uint32
+--ro duplex-type? enumeration
+--ro channel-separation? decimal64
+--ro available-min-output-power? power
+--ro available-max-output-power? power
+--ro available-min-acm? identityref
+--ro available-max-acm? identityref
+--ro available-min-speed? yang:gauge64
+--ro available-max-speed? yang:gauge64
augment /if:interfaces-state/if:interface/if:statistics:
+--ro min-rltm? power
Ahlberg, et al. Expires November 11, 2016 [Page 5]
Internet-Draft Microwave RL YANG May 2016
+--ro max-rltm? power
+--ro min-tltm? power
+--ro max-tltm? power
augment /if:interfaces-state/if:interface/if:statistics:
+--ro bbe? yang:counter32
+--ro es? yang:counter32
+--ro ses? yang:counter32
+--ro uas? yang:counter32
+--ro bber? decimal64
+--ro esr? decimal64
+--ro sesr? decimal64
4. Microwave Module
This YANG module augments the interfaces defined in RFC 7223
[RFC7223].
<CODE BEGINS> file "microwave-radio-link.yang"
module microwave-radio-link {
namespace "urn:ietf:params:xml:ns:yang:microwave-radio-link";
prefix mrl;
import ietf-yang-types {
prefix yang;
}
import ietf-interfaces {
prefix if;
}
import iana-if-type {
prefix ianaift;
}
organization
"IETF CCAMP Working Group";
contact
"jonas.ahlberg@ericsson.com
amy.yemin@huawei.com
jan-olof.carlson@ericsson.com
Marko.Vaupotic@Aviatnet.com
thomas.olausson@ericsson.com";
description
"This is a module for the entities in
a generic microwave system.";
revision 2016-05-10 {
description
"Draft revision.";
Ahlberg, et al. Expires November 11, 2016 [Page 6]
Internet-Draft Microwave RL YANG May 2016
reference "";
}
revision 2016-05-10 {
description
"2nd draft revision.";
reference "";
}
revision 2016-03-11 {
description
"Draft revision.";
reference "";
}
/*
* Features
*/
feature xpic {
description
"Indicates that the device supports XPIC.";
}
feature mimo {
description
"Indicates that the device supports MIMO.";
}
/*
* Interface identities
*/
identity radio-link-terminal {
base ianaift:iana-interface-type;
description
"Interface identity for a radio link terminal.";
}
identity carrier-termination {
base ianaift:iana-interface-type;
description
"Interface identity for a carrier termination.";
}
/*
* Radio-link-terminal mode identities
*/
Ahlberg, et al. Expires November 11, 2016 [Page 7]
Internet-Draft Microwave RL YANG May 2016
identity rlt-mode {
description
"A description of the mode in which the radio link
terminal is configured. The format is X plus Y.
X represent the number of bonded carrier terminations.
Y represent the number of protecting carrier
terminations.";
}
identity one-plus-zero {
base rlt-mode;
description
"1 carrier termination only.";
}
identity one-plus-one {
base rlt-mode;
description
"1 carrier termination
and 1 protecting carrier termination.";
}
identity two-plus-zero {
base rlt-mode;
description
"2 bonded carrier terminations.";
}
identity two-plus-one {
base rlt-mode;
description
"2 bonded carrier terminations and
one protecting carrier termination.";
}
/*
* Coding and modulation identities
*/
identity coding-modulation {
description
"The coding and modulation schemes.";
}
identity half-bpsk-strong {
base coding-modulation;
description
"Half BPSK strong coding and modulation scheme.";
Ahlberg, et al. Expires November 11, 2016 [Page 8]
Internet-Draft Microwave RL YANG May 2016
}
identity half-bpsk {
base coding-modulation;
description
"Half BPSK coding and modulation scheme.";
}
identity half-bpsk-light {
base coding-modulation;
description
"Half BPSK light coding and modulation scheme.";
}
identity bpsk-strong {
base coding-modulation;
description
"BPSK strong coding and modulation scheme.";
}
identity bpsk {
base coding-modulation;
description
"BPSK coding and modulation scheme.";
}
identity bpsk-light {
base coding-modulation;
description
"BPSK light coding and modulation scheme.";
}
identity qpsk {
base coding-modulation;
description
"QPSK coding and modulation scheme.";
}
identity qam-4-strong {
base coding-modulation;
description
"4 QAM strong coding and modulation scheme.";
}
identity qam-4 {
base coding-modulation;
description
"4 QAM coding and modulation scheme.";
Ahlberg, et al. Expires November 11, 2016 [Page 9]
Internet-Draft Microwave RL YANG May 2016
}
identity qam-4-light {
base coding-modulation;
description
"4 QAM light coding and modulation scheme.";
}
identity qam-16-strong {
base coding-modulation;
description
"16 QAM strong coding and modulation scheme.";
}
identity qam-16 {
base coding-modulation;
description
"16 QAM coding and modulation scheme.";
}
identity qam-16-light {
base coding-modulation;
description
"16 QAM light coding and modulation scheme.";
}
identity qam-32-strong {
base coding-modulation;
description
"32 QAM strong coding and modulation scheme.";
}
identity qam-32 {
base coding-modulation;
description
"32 QAM coding and modulation scheme.";
}
identity qam-32-light {
base coding-modulation;
description
"32 QAM light coding and modulation scheme.";
}
identity qam-64-strong {
base coding-modulation;
description
"64 QAM strong coding and modulation scheme.";
Ahlberg, et al. Expires November 11, 2016 [Page 10]
Internet-Draft Microwave RL YANG May 2016
}
identity qam-64 {
base coding-modulation;
description
"64 QAM coding and modulation scheme.";
}
identity qam-64-light {
base coding-modulation;
description
"64 QAM light coding and modulation scheme.";
}
identity qam-128-strong {
base coding-modulation;
description
"128 QAM strong coding and modulation scheme.";
}
identity qam-128 {
base coding-modulation;
description
"128 QAM coding and modulation scheme.";
}
identity qam-128-light {
base coding-modulation;
description
"128 QAM light coding and modulation scheme.";
}
identity qam-256-strong {
base coding-modulation;
description
"256 QAM strong coding and modulation scheme.";
}
identity qam-256 {
base coding-modulation;
description
"256 QAM coding and modulation scheme.";
}
identity qam-256-light {
base coding-modulation;
description
"256 QAM light coding and modulation scheme.";
Ahlberg, et al. Expires November 11, 2016 [Page 11]
Internet-Draft Microwave RL YANG May 2016
}
identity qam-512-strong {
base coding-modulation;
description
"512 QAM strong coding and modulation scheme.";
}
identity qam-512 {
base coding-modulation;
description
"512 QAM coding and modulation scheme.";
}
identity qam-512-light {
base coding-modulation;
description
"512 QAM light coding and modulation scheme.";
}
identity qam-1024-strong {
base coding-modulation;
description
"1024 QAM strong coding and modulation scheme.";
}
identity qam-1024 {
base coding-modulation;
description
"1024 QAM coding and modulation scheme.";
}
identity qam-1024-light {
base coding-modulation;
description
"1024 QAM light coding and modulation scheme.";
}
identity qam-2048-strong {
base coding-modulation;
description
"2048 QAM strong coding and modulation scheme.";
}
identity qam-2048 {
base coding-modulation;
description
"2048 QAM coding and modulation scheme.";
Ahlberg, et al. Expires November 11, 2016 [Page 12]
Internet-Draft Microwave RL YANG May 2016
}
identity qam-2048-light {
base coding-modulation;
description
"2048 QAM light coding and modulation scheme.";
}
identity qam-4096-strong {
base coding-modulation;
description
"4096 QAM strong coding and modulation scheme.";
}
identity qam-4096 {
base coding-modulation;
description
"4096 QAM coding and modulation scheme.";
}
identity qam-4096-light {
base coding-modulation;
description
"4096 QAM light coding and modulation scheme.";
}
/*
* Spectrum Efficiency Class identities
*/
identity spectrum-efficiency-class {
description
"Spectrum Efficiency Class (SEC).";
}
identity class-1 {
base spectrum-efficiency-class;
description
"Spectrum Efficiency Class 1.";
}
identity class-2 {
base spectrum-efficiency-class;
description
"Spectrum Efficiency Class 2.";
}
identity class-3 {
Ahlberg, et al. Expires November 11, 2016 [Page 13]
Internet-Draft Microwave RL YANG May 2016
base spectrum-efficiency-class;
description
"Spectrum Efficiency Class 3.";
}
identity class-4l {
base spectrum-efficiency-class;
description
"Spectrum Efficiency Class 4l.";
}
identity class-4h {
base spectrum-efficiency-class;
description
"Spectrum Efficiency Class 4h.";
}
identity class-5l {
base spectrum-efficiency-class;
description
"Spectrum Efficiency Class 5l.";
}
identity class-5la {
base spectrum-efficiency-class;
description
"Spectrum Efficiency Class 5la.";
}
identity class-5lb {
base spectrum-efficiency-class;
description
"Spectrum Efficiency Class 5lb.";
}
identity class-5h {
base spectrum-efficiency-class;
description
"Spectrum Efficiency Class 5h.";
}
identity class-5ha {
base spectrum-efficiency-class;
description
"Spectrum Efficiency Class 5ha.";
}
identity class-5hb {
Ahlberg, et al. Expires November 11, 2016 [Page 14]
Internet-Draft Microwave RL YANG May 2016
base spectrum-efficiency-class;
description
"Spectrum Efficiency Class 5hb.";
}
identity class-6l {
base spectrum-efficiency-class;
description
"Spectrum Efficiency Class 6l.";
}
identity class-6la {
base spectrum-efficiency-class;
description
"Spectrum Efficiency Class 6la.";
}
identity class-6lb {
base spectrum-efficiency-class;
description
"Spectrum Efficiency Class 6lb.";
}
identity class-6h {
base spectrum-efficiency-class;
description
"Spectrum Efficiency Class 6h.";
}
identity class-6ha {
base spectrum-efficiency-class;
description
"Spectrum Efficiency Class 6ha.";
}
identity class-6hb {
base spectrum-efficiency-class;
description
"Spectrum Efficiency Class 6hb.";
}
identity class-7 {
base spectrum-efficiency-class;
description
"Spectrum Efficiency Class 7.";
}
identity class-7a {
Ahlberg, et al. Expires November 11, 2016 [Page 15]
Internet-Draft Microwave RL YANG May 2016
base spectrum-efficiency-class;
description
"Spectrum Efficiency Class 7a.";
}
identity class-7b {
base spectrum-efficiency-class;
description
"Spectrum Efficiency Class 7b.";
}
identity class-8 {
base spectrum-efficiency-class;
description
"Spectrum Efficiency Class 8.";
}
identity class-8a {
base spectrum-efficiency-class;
description
"Spectrum Efficiency Class 8a.";
}
identity class-8b {
base spectrum-efficiency-class;
description
"Spectrum Efficiency Class 8b.";
}
/*
* Typedefs
*/
typedef power {
type decimal64 {
fraction-digits 1;
}
description
"Type used for power values, selected and measured.";
}
/*
* G.826 stats grouping
*/
grouping g826-stats {
description
"G.826 statistics operational data ";
Ahlberg, et al. Expires November 11, 2016 [Page 16]
Internet-Draft Microwave RL YANG May 2016
leaf bbe {
type yang:counter32;
units "number of block errors";
description
"Number of Background Block Errors (BBE) during the
interval. A BBE is an errored block not occurring as
part of an SES.";
}
leaf es {
type yang:counter32;
units "seconds";
description
"Number of Errored Seconds (ES) since last reset.
An ES is a one-second period with one or more errored
blocks or at least one defect.";
}
leaf ses {
type yang:counter32;
units "seconds";
description
"Number of Severely Errored Seconds (SES) during the
interval. SES is a one-second period which contains
equal or more than 30% errored blocks or at least
one defect. SES is a subset of ES.";
}
leaf uas {
type yang:counter32;
units "seconds";
description
"Number of Unavailable Seconds (UAS), that is, the
total time that the node has been unavailable during
a fixed measurement interval.";
}
leaf bber {
type decimal64 {
fraction-digits 18;
}
units "ratio";
description
"Background Block Error (BBER) ratio, that is, the
ratio of errored blocks to total blocks during a fixed
measurement interval. BBER does not include any blocks
during SES and Unavailable Time.";
}
Ahlberg, et al. Expires November 11, 2016 [Page 17]
Internet-Draft Microwave RL YANG May 2016
leaf esr {
type decimal64 {
fraction-digits 18;
}
units "ratio";
description
"Errored Seconds (ESR) ratio, that is, the ratio of
Errored Seconds to Available Time during a fixed
measurement interval.";
}
leaf sesr {
type decimal64 {
fraction-digits 18;
}
units "ratio";
description
"Severely Errored Seconds Ratio (SESR), that is, the
ratio of SES to total seconds in Available Time during
a fixed measurement interval.";
}
}
/*
* Radio Link Terminal (RLT) - Configuration data nodes
*/
augment "/if:interfaces/if:interface" {
when "if:type = 'mrl:radio-link-terminal'";
description
"Addition of data nodes for radio link terminal to
the standard Interface data model, for interfaces of
the type 'radio-link-terminal'.";
leaf id {
type string;
default "";
description
"ID of the radio link terminal. Used by far-end when
checking that it's connected to the correct RLT.";
}
leaf mode {
type identityref {
base rlt-mode;
}
default "one-plus-zero";
description
"A description of the mode in which the radio link
terminal is configured. The format is X plus Y.
Ahlberg, et al. Expires November 11, 2016 [Page 18]
Internet-Draft Microwave RL YANG May 2016
X represent the number of bonded carrier terminations.
Y represent the number of protecting carrier
terminations.";
}
leaf expected-far-end-id {
type string;
default "";
description
"Expected ID of the radio link terminal at far-end.";
}
leaf far-end-id-check {
type boolean;
default "false";
description
"Enable(true)/disable(false) check of the ID of the
radio link terminal at far-end. When true, the system
verifies that far-end radio link terminal ID is equal to
the expected. If ok then the radio link terminal status
is UP. If not ok, then the status is stated as DOWN.";
}
leaf-list carrier-terminations {
type if:interface-ref;
must "/if:interfaces/if:interface[if:name = current()]"
+ "/if:type = 'carrier-termination'" {
description
"The type of interface must be
'carrier-termination'.";
}
description
"A list of references to carrier terminations
included in the radio link terminal.";
}
leaf-list rlp-pairs {
type leafref {
path "/mrl:radio-link-protection-pairs/"
+ "mrl:radio-link-protection-pair/mrl:name";
}
description
"A list of references to the carrier termination
pairs configured for radio link protection in this
radio link terminal.";
}
leaf-list xpic-pairs {
if-feature xpic;
type leafref {
path "/mrl:xpic-pairs/mrl:xpic-pair/mrl:name";
}
description
Ahlberg, et al. Expires November 11, 2016 [Page 19]
Internet-Draft Microwave RL YANG May 2016
"A list of references to the XPIC pairs used in this
radio link terminal. One pair can be used by two
terminals.";
}
leaf mimo-group {
if-feature mimo;
type leafref {
path "/mrl:mimo-groups/mrl:mimo-group/mrl:name";
}
description
"A reference to the MIMO group used in this
radio link terminal. One group can be used by more
than one terminal.";
}
}
/*
* Carrier Termination - Configuration data nodes
*/
augment "/if:interfaces/if:interface" {
when "if:type = 'mrl:carrier-termination'";
description
"Addition of data nodes for carrier termination to the
standard Interface data model, for interfaces of the type
'carrier-termination'.";
leaf carrier-id {
type string;
default "A";
description
"ID of the carrier. (e.g. A, B, C or D)
Used in XPIC & MIMO configurations to check that the
carrier termination is connected to the correct far-end
carrier termination. Should be the same carrier ID on
both sides of the hop.
Defaulted when not MIMO or XPIC.";
}
leaf tx-admin-status {
type enumeration {
enum "off" {
description "Transmitter is disabled.";
}
enum "on" {
description "Transmitter is enabled.";
}
}
description
Ahlberg, et al. Expires November 11, 2016 [Page 20]
Internet-Draft Microwave RL YANG May 2016
"The adminstrative status of the transmitter.
Disables (off) or enables (on) the transmitter.
Only applicable when the interface is enabled
(interface:enabled = true) otherwise it's always
disabled.";
}
leaf tx-frequency {
type uint32;
units "kHz";
default "0";
description
"Selected transmitter frequency.";
}
leaf rx-frequency {
type uint32;
units "kHz";
default "0";
description
"Selected receiver frequency.
Only writeable when duplex-config=disabled and
duplex-type=variable.";
}
leaf duplex-distance {
type uint32;
units "kHz";
default "0";
description
"Distance between Tx & Rx frequencies.
Only writeable when duplex-config=true and
duplex-type=variable.";
}
leaf duplex-config {
type boolean;
default "false";
description
"Enable (true) or disable (false) configuration of
rxFrequency using a defined duplex distance.";
}
leaf polarization {
type enumeration {
enum "horizontal" {
description "Horizontal polarization.";
}
enum "vertical" {
description "Vertical polarization.";
}
enum "not-specified" {
description "Polarization not specified.";
Ahlberg, et al. Expires November 11, 2016 [Page 21]
Internet-Draft Microwave RL YANG May 2016
}
}
default "not-specified";
description
"Polarization - A textual description for info only.";
}
leaf power-mode {
type enumeration {
enum rtpc {
description "Remote Transmit Power Control (RTPC).";
}
enum atpc {
description "Automatic Transmit Power Control (ATPC).";
}
}
description
"A choice of Remote Transmit Power Control (RTPC)
or Automatic Transmit Power Control (ATPC).";
}
leaf selected-output-power {
when "../power-mode = 'rtpc'";
type power {
range "-99..40";
}
units "dBm";
description
"Selected output power in RTPC mode.";
}
leaf selected-min-output-power {
when "../power-mode = 'atpc'";
type power {
range "-99..40";
}
units "dBm";
description
"Selected minimum output power in
ATPC mode.";
}
leaf selected-max-output-power {
when "../power-mode = 'atpc'";
type power {
range "-99..40";
}
units "dBm";
description
Ahlberg, et al. Expires November 11, 2016 [Page 22]
Internet-Draft Microwave RL YANG May 2016
"Selected maximum output power in
ATPC mode.";
}
leaf target-input-power-far-end {
when "../power-mode = 'atpc'";
type power {
range "-99..-30";
}
units "dBm";
description
"The wanted received input power at far-end,
when running ATPC.";
}
leaf reference-sec {
type identityref {
base spectrum-efficiency-class;
}
description
"Each modulation is compliant to a Spectrum Efficiency
Class (SEC). When running Adaptive Coding/Modulation,
one SEC has to be selected for all the coding/
modulations between selected-min-acm and
selected-max-acm. This parameter is called Reference
SEC. This setting might affect
available-max-output-power, in order to fulfill
spectrum requirements.";
}
leaf coding-modulation-mode {
type enumeration {
enum fixed {
description "Fixed coding/modulation.";
}
enum adaptive {
description "Adaptive coding/modulation.";
}
}
description
"A selection of fixed or
adaptive coding/modulation mode.";
}
leaf selected-cm {
when "../coding-modulation-mode = 'fixed'";
type identityref {
base coding-modulation;
}
Ahlberg, et al. Expires November 11, 2016 [Page 23]
Internet-Draft Microwave RL YANG May 2016
description
"Selected fixed coding/modulation.";
}
leaf selected-min-acm {
when "../coding-modulation-mode = 'adaptive'";
type identityref {
base coding-modulation;
}
description
"Selected minimum coding/modulation.
Adaptive coding/modulation shall not go
below this value.";
}
leaf selected-max-acm {
when "../coding-modulation-mode = 'adaptive'";
type identityref {
base coding-modulation;
}
description
"Selected maximum coding/modulation.
Adaptive coding/modulation shall not go
above this value.";
}
leaf if-loop {
type boolean;
default "false";
description
"Enable (true) or disable (false) the IF loop,
which loops the signal back to the client side
(not the radio side).";
}
leaf rf-loop {
type boolean;
default "false";
description
"Enable (true) or disable (false) the RF loop,
which loops the signal back to the client side
(not the radio side).";
}
container ct-performance-thresholds {
description
"Specification of thresholds for when alarms should
be sent and cleared for various performance counters.";
leaf input-power-alarm-threshold {
type power {
Ahlberg, et al. Expires November 11, 2016 [Page 24]
Internet-Draft Microwave RL YANG May 2016
range "-99..-30";
}
units "dBm";
default "-93";
description
"Specification of at which input power an alarm should
be raised.";
}
leaf output-power-alarm-threshold {
type power {
range "-99..40";
}
units "dBm";
description
"An alarm is sent when the actual output power is
below the specified threshold.";
}
leaf ber-alarm-threshold {
type enumeration {
enum "10e-9" {
description "Threshold at 10e-9.";
}
enum "10e-8" {
description "Threshold at 10e-8.";
}
enum "10e-7" {
description "Threshold at 10e-7.";
}
enum "10e-6" {
description "Threshold at 10e-6.";
}
enum "10e-5" {
description "Threshold at 10e-5.";
}
enum "10e-4" {
description "Threshold at 10e-4.";
}
enum "10e-3" {
description "Threshold at 10e-3.";
}
enum "10e-2" {
description "Threshold at 10e-2.";
}
enum "10e-1" {
description "Threshold at 10e-1.";
}
}
default "10e-6";
Ahlberg, et al. Expires November 11, 2016 [Page 25]
Internet-Draft Microwave RL YANG May 2016
description
"Specification of at which BER an alarm should
be raised.";
}
leaf rl-1-threshold-level {
type power {
range "-99..40";
}
units "dBm";
description
"Specifies the threshold level for Received Level 1.
When the received level (input power) is below this
level the Received Level Threshold Seconds 1 (RLTS1)
is counted.";
}
leaf rlts-1-15min-set-alarm-threshold {
type uint16 {
range "1..900";
}
units "seconds";
description
"Specifies the threshold value in seconds for RLTS1.
An alarm is send as soon as the received level has
been below the Received Level 1 threshold for the
number of seconds configured in this threshold
during a 15 minutes interval.";
}
leaf rlts-1-15min-reset-alarm-threshold {
type uint16 {
range "1..900";
}
units "seconds";
description
"Specifies the threshold value in seconds for RLTS1.
An alarm clearing is sent when the received level
has been below the RLTS1 threshold less seconds than
indicated by this threshold for a 15 minutes
interval.";
}
leaf rlts-1-24h-set-alarm-threshold {
type uint32 {
range "1..86400";
}
units "seconds";
description
"Specifies the threshold value in seconds for RLTS1.
An alarm is send as soon as the received level has
been below the Received Level 1 threshold for the
Ahlberg, et al. Expires November 11, 2016 [Page 26]
Internet-Draft Microwave RL YANG May 2016
number of seconds configured in this threshold
during a 24 hours interval.
The alarm is cleared after the next 24 hours if
the threshold is not crossed.";
}
leaf tl-1-threshold-level {
type power {
range "-100..35";
}
units "dBm";
description
"Specifies the threshold level for Transmitted
Level 1. When the transmitted level (output power)
is above this level the Transmitted Level Threshold
Seconds 1 (TLTS1) is counted.";
}
leaf tlts-1-15min-set-alarm-threshold {
type power {
range "1..900";
}
units "seconds";
description
"Specifies the threshold value in seconds for TLTS1.
An alarm is send as soon as the transmitted level
has been above the Transmitted Level 1 threshold
for the number of seconds configured in this
threshold during a 15 minutes interval.";
}
leaf tlts-1-15min-reset-alarm-threshold {
type power {
range "1..900";
}
units "seconds";
description
"Specifies the threshold value in seconds for TLTS1.
An alarm clearing is sent when the transmitted level
has been above the TLTS1 threshold less seconds than
indicated by this threshold for a 15 minutes
interval.";
}
leaf tlts-1-24h-set-alarm-threshold {
type uint32 {
range "1..86400";
}
units "seconds";
description
"Specifies the threshold value in seconds for TLTS1.
An alarm is send as soon as the transmitted level
Ahlberg, et al. Expires November 11, 2016 [Page 27]
Internet-Draft Microwave RL YANG May 2016
has been above the Transmitted Level 1 threshold for
the number of seconds configured in this threshold
during a 24 hours interval.
The alarm is cleared after the next 24 hours if
the threshold is not crossed.";
}
leaf es-15min-set-alarm-threshold {
type uint16 {
range "1..900";
}
units "seconds";
description
"An alarm is sent when the number of Errored Seconds
(es) exceeds the specified threshold in a
15 minutes interval.";
}
leaf es-15min-reset-alarm-threshold {
type uint16 {
range "1..900";
}
units "seconds";
description
"An alarm clearing is sent when the the number of
Errored Seconds (es) has been below the specified
threshold in a 15 minutes interval.";
}
leaf es-24h-set-alarm-threshold {
type uint32 {
range "1..86400";
}
units "seconds";
description
"An alarm is sent when the number of Errored Seconds
(es) exceeds the specified threshold in a
24 hours interval.
The alarm is cleared after the next 24 hours if
the threshold is not crossed.";
}
leaf ses-15min-set-alarm-threshold {
type uint16 {
range "1..900";
}
units "seconds";
description
"An alarm is sent when the number of Severely
Errored Seconds (ses) exceeds the specified
threshold in a 15 minutes interval.";
}
Ahlberg, et al. Expires November 11, 2016 [Page 28]
Internet-Draft Microwave RL YANG May 2016
leaf ses-15min-reset-alarm-threshold {
type uint16 {
range "1..900";
}
units "seconds";
description
"An alarm clearing is sent when the the number of
Severely Errored Seconds (ses) has been below the
specified threshold in a 15 minutes interval.";
}
leaf ses-24h-set-alarm-threshold {
type uint32 {
range "1..86400";
}
units "seconds";
description
"An alarm is sent when the number of Severely
Errored Seconds (ses) exceeds the specified
threshold in a 24 hours interval.
The alarm is cleared after the next 24 hours if
the threshold is not crossed.";
}
leaf bbe-15min-set-alarm-threshold {
type uint32;
units "number of block errors";
description
"An alarm is sent when the number of Background
Block Errors (bbe) exceeds the specified threshold
in a 15 minutes interval.";
}
leaf bbe-15min-reset-alarm-threshold {
type uint32;
units "number of block errors";
description
"An alarm clearing is sent when the the number of
Background Block Errors (bbe) has been below the
specified threshold in a 15 minutes interval.";
}
leaf bbe-24h-set-alarm-threshold {
type uint32;
units "number of block errors";
description
"An alarm is sent when the number of Background
Block Errors (bbe) exceeds the specified threshold
in a 24 hours interval.
The alarm is cleared after the next 24 hours if
the threshold is not crossed.";
}
Ahlberg, et al. Expires November 11, 2016 [Page 29]
Internet-Draft Microwave RL YANG May 2016
leaf acm-15min-set-alarm-threshold {
type uint16 {
range "1..900";
}
units "seconds";
description
"An alarm is sent when time in minimum coding &
modulation (selected-min-acm) exceeds the specified
threshold in a 15 minutes interval.";
}
leaf acm-15min-reset-alarm-threshold {
type uint16 {
range "1..900";
}
units "seconds";
description
"An alarm clearing is sent when the the time in
minimum coding & modulation (selected-min-acm)
has been below the specified threshold in a 15 minutes
interval.";
}
leaf acm-24h-set-alarm-threshold {
type uint32 {
range "1..86400";
}
units "seconds";
description
"An alarm is sent when time in minimum coding &
modulation (selected-min-acm) exceeds the specified
threshold in a 24 hours interval.
The alarm is cleared after the next 24 hours if
the threshold is not crossed.";
}
}
}
/*
* Carrier Termination - Operational state data nodes
*/
augment "/if:interfaces-state/if:interface" {
when "if:type = 'mrl:carrier-termination'";
description
"Addition of state data nodes for carrier termination to
the standard Interface state data model, for interfaces of
the type 'carrier-termination'.";
leaf tx-oper-status {
type enumeration {
Ahlberg, et al. Expires November 11, 2016 [Page 30]
Internet-Draft Microwave RL YANG May 2016
enum "off" {
description "Transmitter is off.";
}
enum "on" {
description "Transmitter is on.";
}
enum "standby" {
description "Transmitter is in standby.";
}
}
description
"Shows the operative status of the transmitter.";
}
leaf actual-ouput-power {
type power {
range "-99..40";
}
units "dBm";
description
"Actual transmitted output power (0.1 dBm resolution).";
}
leaf actual-input-power {
type power {
range "-99..-20";
}
units "dBm";
description
"Actual input power (0.1 dBm resolution).";
}
leaf actual-tx-cm {
type identityref {
base coding-modulation;
}
description
"Actual coding/modulation in transmitting direction.";
}
leaf actual-rx-cm {
type identityref {
base coding-modulation;
}
description
"Actual coding/modulation in receiving direction.";
}
leaf selected-min-speed {
type yang:gauge64;
units "bit/s";
description
"Selected minimum speed, derived from selected-min-acm
Ahlberg, et al. Expires November 11, 2016 [Page 31]
Internet-Draft Microwave RL YANG May 2016
(adaptive) or selected-cm (fixed).";
}
leaf selected-max-speed {
type yang:gauge64;
units "bit/s";
description
"Selected maximum speed, derived from selected-max-acm
(adaptive) or selected-cm (fixed).";
}
leaf xpic-status {
if-feature xpic;
type enumeration {
enum "locked" {
description "XPIC status is locked.";
}
enum "unlocked" {
description "XPIC status is unlocked.";
}
enum "na" {
description "XPIC status is not applicable.";
}
}
description
"Status of the XPIC. Only valid if XPIC is enabled.";
}
leaf mimo-status {
if-feature mimo;
type enumeration {
enum "locked" {
description "MIMO status is locked.";
}
enum "unlocked" {
description "MIMO status is unlocked.";
}
enum "na" {
description "MIMO status is not applicable.";
}
}
description
"Status of the MIMO. Only valid if MIMO is enabled.";
}
leaf actual-snir {
type decimal64 {
fraction-digits 1;
range "0..99";
}
units "dB";
description
Ahlberg, et al. Expires November 11, 2016 [Page 32]
Internet-Draft Microwave RL YANG May 2016
"Actual signal to noise plus interference ratio.
(0.1 dB resolution).";
}
leaf actual-xpi {
if-feature xpic;
type decimal64 {
fraction-digits 1;
range "0..99";
}
units "dBc";
description
"The actual carrier to cross-polar interference.
Only valid if XPIC is enabled. (0.1 dBc resolution).";
}
leaf actual-si {
if-feature mimo;
type decimal64 {
fraction-digits 1;
range "-99..99";
}
units "dBc";
description
"Actual MIMO Spatial Interference.
Only valid if MIMO is enabled. (0.1 dBc resolution).";
}
container capabilities {
description
"Capabilities of the the installed equipment and
some selected configurations.";
leaf min-tx-frequency {
type uint32;
units "kHz";
description
"Minimum Tx frequency possible to use.";
}
leaf max-tx-frequency {
type uint32;
units "kHz";
description
"Maximum Tx frequency possible to use.";
}
leaf min-rx-frequency {
type uint32;
units "kHz";
description
"Minimum Rx frequency possible to use.";
}
leaf max-rx-frequency {
Ahlberg, et al. Expires November 11, 2016 [Page 33]
Internet-Draft Microwave RL YANG May 2016
type uint32;
units "kHz";
description
"Maximum Tx frequency possible to use.";
}
leaf duplex-type {
type enumeration {
enum "fixed" {
description "Duplex distance is fixed.";
}
enum "variable" {
description "Duplex distance is variable.";
}
}
description
"The duplex type is given by the equipment used.
It can be a fixed duplex distance or a variable
distance which can be configured by selecting
rx-frequency or duplex-distance.";
}
leaf channel-separation {
type decimal64 {
fraction-digits 1;
}
units "MHz";
description
"The amount of bandwidth allocated to a carrier.";
}
leaf available-min-output-power {
type power;
units "dBm";
description
"The minimum output power supported.";
}
leaf available-max-output-power {
type power;
units "dBm";
description
"The maximum output power supported.";
}
leaf available-min-acm {
type identityref {
base coding-modulation;
}
description
"Minimum coding-modulation possible to use.";
}
leaf available-max-acm {
Ahlberg, et al. Expires November 11, 2016 [Page 34]
Internet-Draft Microwave RL YANG May 2016
type identityref {
base coding-modulation;
}
description
"Maximum coding-modulation possible to use.";
}
leaf available-min-speed {
type yang:gauge64;
units "bit/s";
description
"Minimum speed that can be supported given
by the available-min-acm.";
}
leaf available-max-speed {
type yang:gauge64;
units "bit/s";
description
"Maximum speed that can be supported given
by the available-max-acm.";
}
}
}
augment "/if:interfaces-state/if:interface/if:statistics" {
when "../if:type = 'mrl:carrier-termination'";
description
"Addition of state data nodes in the container statistics
for carrier terminations to the standard Interface data
model, for interfaces of the type 'carrier-termination'.";
leaf min-rltm {
type power {
range "-99..-20";
}
units "dBm";
description
"Minimum input power since last reset.";
}
leaf max-rltm {
type power {
range "-99..-20";
}
units "dBm";
description
"Maximum input power since last reset.";
}
leaf min-tltm {
Ahlberg, et al. Expires November 11, 2016 [Page 35]
Internet-Draft Microwave RL YANG May 2016
type power {
range "-99..40";
}
units "dBm";
description
"Minimum output power since last reset.";
}
leaf max-tltm {
type power {
range "-99..40";
}
units "dBm";
description
"Maximum output power since last reset.";
}
}
augment "/if:interfaces-state/if:interface/if:statistics" {
when "(../if:type = 'mrl:carrier-termination') or
(../if:type = 'mrl:radio-link-terminal')";
description
"Addition of G.826 statsistics in the container statistics
of the standard Interface state data model.";
uses g826-stats;
}
/*
* Radio Link Protection Pairs - Configuration data nodes
*/
container radio-link-protection-pairs {
description
"Configuration of radio link protected pairs (1+1) of
carrier terminations in a radio link. More than one
protected pair per radio-link-terminal is allowed.";
list radio-link-protection-pair {
key "name";
description
"List of protected pairs of carrier terminations
in a radio link.";
leaf name {
type string;
description
"Name used for identification of the radio
link protection pair";
}
leaf protection-switch-mode {
Ahlberg, et al. Expires November 11, 2016 [Page 36]
Internet-Draft Microwave RL YANG May 2016
type enumeration {
enum "manual" {
description
"Automatic switching is disabled and
operator can select Tx manually.";
}
enum "auto" {
description
"System automatically switches from the degraded
to the other receiver(Rx) or transmitter (Tx).";
}
enum "auto-and-revertive" {
description
"Makes it possible to manually set the preferred Tx.";
}
}
default "auto";
description
"The mode in which the switching mechanism is
configured.
Auto - System automatically switches from the
degraded to the other receiver(Rx) or transmitter (Tx).
Manual - Automatic switching is disabled and
operator can select Tx manually.
Auto & Revertive - makes it possible to manually
set the preferred Tx.";
}
leaf revertive-preferred-tx {
type if:interface-ref;
must "/if:interfaces/if:interface[if:name = current()]"
+ "/if:type = 'carrier-termination'" {
description
"The type of a preferred-tx must be
'carrier-termination'.";
}
description
"Association to the preferred carrier
termination in revertive protection mode.";
}
leaf revertive-wait-to-restore {
type uint16;
units "seconds";
default "0";
description
"The time to wait before switching back to the
preferred Tx in Auto & Revertive mode.";
}
leaf-list radio-link-protection-members {
Ahlberg, et al. Expires November 11, 2016 [Page 37]
Internet-Draft Microwave RL YANG May 2016
type if:interface-ref;
must "/if:interfaces/if:interface[if:name = current()]"
+ "/if:type = 'carrier-termination'" {
description
"The type of a protection member must be
'carrier-termination'.";
}
min-elements 2;
max-elements "2";
description
"Association to a pair of carrier terminations
configured for radio link protection and used in
the radio link terminal.";
}
}
}
/*
* Radio Link Protection Pairs - Configuration state data nodes
*/
container radio-link-protection-pairs-state {
config false;
description
"State data for radio link protected pairs (1+1) of
carrier terminations in a radio link.";
list radio-link-protection-pair {
key "name";
description
"List of protected pairs of carrier terminations
in a radio link.";
leaf name {
type string;
description
"Name used for identification of the radio
link protection pair.";
}
leaf protection-status {
type enumeration {
enum "unprotected" {
description "Not protected";
}
enum "protected" {
description "Protected";
}
enum "unable-to-protect" {
description "Unable to protect";
}
Ahlberg, et al. Expires November 11, 2016 [Page 38]
Internet-Draft Microwave RL YANG May 2016
}
description
"Status of the protection, in a pair of carrier
terminations configured in a radio link protection
mode.";
}
leaf actual-wait-to-restore {
when "/radio-link-protection-pairs/"
+ "radio-link-protection-pair[name = current()]"
+ "/protection-switch-mode = 'auto-and-revertive'";
type uint16;
units "seconds";
description
"The actual time to wait before switching back to the
preferred Tx in Auto & Revertive mode.";
}
}
}
/*
* XPIC & MIMO groups - Configuration data nodes
*/
container xpic-pairs {
if-feature xpic;
description
"Configuration of carrier termination pairs
for operation in XPIC mode.";
list xpic-pair {
key "name";
description
"List of carrier termination pairs in XPIC mode.";
leaf name {
type string;
description
"Name used for identification of the XPIC pair.";
}
leaf enabled {
type boolean;
default "false";
description
"Enable(true)/disable(false) XPIC";
}
leaf-list xpic-members {
type if:interface-ref;
must "/if:interfaces/if:interface[if:name = current()]"
+ "/if:type = 'carrier-termination'" {
description
Ahlberg, et al. Expires November 11, 2016 [Page 39]
Internet-Draft Microwave RL YANG May 2016
"The type of a xpic-member must be
'carrier-termination'.";
}
min-elements 2;
max-elements "2";
description
"Association to XPIC pairs used in the radio link
terminal.";
}
}
}
container mimo-groups {
if-feature mimo;
description
"Configuration of carrier terminations
for operation in MIMO mode.";
list mimo-group {
key "name";
description
"List of carrier terminations in MIMO mode.";
leaf name {
type string;
description
"Name used for identification of the MIMO group.";
}
leaf enabled {
type boolean;
default "false";
description
"Enable(true)/disable(false) MIMO";
}
leaf-list mimo-members {
type if:interface-ref;
must "/if:interfaces/if:interface[if:name = current()]"
+ "/if:type = 'carrier-termination'" {
description
"The type of a mimo-member must be
'carrier-termination'.";
}
min-elements 2;
description
"Association to a MIMO group if used in the radio
link terminal.";
}
}
}
}
<CODE ENDS>
Ahlberg, et al. Expires November 11, 2016 [Page 40]
Internet-Draft Microwave RL YANG May 2016
5. Acknowledgements
6. IANA Considerations
This document defines a new YANG module and the authors politely
request that IANA assigns unique names to the YANG module file
contained within this draft, and also appropriate URIs in the "IETF
XML Registry".
7. Security Considerations
The YANG module defined in this memo is designed to be accessed via
the NETCONF protocol RFC 6241 [RFC6241]. The lowest NETCONF layer is
the secure transport layer and the mandatory to implement secure
transport is SSH RFC 6242 [RFC6242]. The NETCONF access control
model RFC 6536 [RFC6536] provides the means to restrict access for
particular NETCONF users to a pre-configured subset of all available
NETCONF protocol operations and content.
There are a number of data nodes defined in this YANG module which
are writable/creatable/deletable (i.e. config true, which is the
default). These data nodes may be considered sensitive or vulnerable
in some network environments. Write operations (e.g. edit-config) to
these data nodes without proper protection can have a negative effect
on network operations. These are the subtrees and data nodes and
their sensitivity/vulnerability:
8. References
8.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<http://www.rfc-editor.org/info/rfc2119>.
[RFC6020] Bjorklund, M., Ed., "YANG - A Data Modeling Language for
the Network Configuration Protocol (NETCONF)", RFC 6020,
DOI 10.17487/RFC6020, October 2010,
<http://www.rfc-editor.org/info/rfc6020>.
[RFC7223] Bjorklund, M., "A YANG Data Model for Interface
Management", RFC 7223, DOI 10.17487/RFC7223, May 2014,
<http://www.rfc-editor.org/info/rfc7223>.
Ahlberg, et al. Expires November 11, 2016 [Page 41]
Internet-Draft Microwave RL YANG May 2016
8.2. Informative References
[RFC6241] Enns, R., Ed., Bjorklund, M., Ed., Schoenwaelder, J., Ed.,
and A. Bierman, Ed., "Network Configuration Protocol
(NETCONF)", RFC 6241, DOI 10.17487/RFC6241, June 2011,
<http://www.rfc-editor.org/info/rfc6241>.
[RFC6242] Wasserman, M., "Using the NETCONF Protocol over Secure
Shell (SSH)", RFC 6242, DOI 10.17487/RFC6242, June 2011,
<http://www.rfc-editor.org/info/rfc6242>.
[RFC6536] Bierman, A. and M. Bjorklund, "Network Configuration
Protocol (NETCONF) Access Control Model", RFC 6536,
DOI 10.17487/RFC6536, March 2012,
<http://www.rfc-editor.org/info/rfc6536>.
Authors' Addresses
Jonas Ahlberg
Ericsson AB
Sweden
Email: jonas.ahlberg@ericsson.com
Jan-Olof Carlson
Ericsson AB
Sweden
Email: jan-olof.carlson@ericsson.com
Hans-Ake Lund
Ericsson AB
Sweden
Email: hans-ake.lund@ericsson.com
Thomas Olausson
Ericsson AB
Sweden
Email: thomas.olausson@ericsson.com
Ahlberg, et al. Expires November 11, 2016 [Page 42]
Internet-Draft Microwave RL YANG May 2016
Min Ye
Huawei Technologies Co.
P.R.China
Email: amy.yemin@huawei.com
Marko Vaupotic
Aviat Networks
Slovenia
Email: Marko.Vaupotic@Aviatnet.com
Ahlberg, et al. Expires November 11, 2016 [Page 43]