IPPM WG K. Pentikousis, Ed.
Internet-Draft EICT
Intended status: Standards Track E. Zhang
Expires: November 30, 2015 Y. Cui
Huawei Technologies
May 29, 2015
IKEv2-derived Shared Secret Key for O/TWAMP
draft-ietf-ippm-ipsec-10
Abstract
The One-way Active Measurement Protocol (OWAMP) and Two-Way Active
Measurement Protocol (TWAMP) security mechanisms require that both
the client and server endpoints possess a shared secret. This
document describes the use of keys derived from an IKEv2 security
association (SA) as the shared key in O/TWAMP. If the shared key can
be derived from the IKEv2 SA, O/TWAMP can support certificate-based
key exchange, which would allow for more operational flexibility and
efficiency. The key derivation presented in this document can also
facilitate automatic key management.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on November 30, 2015.
Copyright Notice
Copyright (c) 2015 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
Pentikousis, et al. Expires November 30, 2015 [Page 1]
Internet-Draft IKEv2-derived Shared Secret Key for O/TWAMP May 2015
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 4
3. Scope and Applicability . . . . . . . . . . . . . . . . . . . 4
4. O/TWAMP Security . . . . . . . . . . . . . . . . . . . . . . 4
4.1. O/TWAMP-Control Security . . . . . . . . . . . . . . . . 5
4.2. O/TWAMP-Test Security . . . . . . . . . . . . . . . . . . 6
4.3. O/TWAMP Security Root . . . . . . . . . . . . . . . . . . 7
5. O/TWAMP for IPsec Networks . . . . . . . . . . . . . . . . . 7
5.1. Shared Key Derivation . . . . . . . . . . . . . . . . . . 7
5.2. Server Greeting Message Update . . . . . . . . . . . . . 8
5.3. Set-Up-Response Update . . . . . . . . . . . . . . . . . 9
5.4. O/TWAMP over an IPsec tunnel . . . . . . . . . . . . . . 11
6. Security Considerations . . . . . . . . . . . . . . . . . . . 11
7. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 11
8. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 12
9. References . . . . . . . . . . . . . . . . . . . . . . . . . 12
9.1. Normative References . . . . . . . . . . . . . . . . . . 12
9.2. Informative References . . . . . . . . . . . . . . . . . 13
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 13
1. Introduction
The One-way Active Measurement Protocol (OWAMP) [RFC4656] and the
Two-Way Active Measurement Protocol (TWAMP) [RFC5357] can be used to
measure network performance parameters such as latency, bandwidth,
and packet loss by sending probe packets and monitoring their
experience in the network. In order to guarantee the accuracy of
network measurement results, security aspects must be considered.
Otherwise, attacks may occur and the authenticity of the measurement
results may be violated. For example, if no protection is provided,
an adversary in the middle may modify packet timestamps, thus
altering the measurement results.
The currently-standardized O/TWAMP security mechanism [RFC4656]
[RFC5357] requires that endpoints (i.e. both the client and the
server) possess a shared secret. In today's network deployments,
however, the use of pre-shared keys is far from optimal. For
example, in wireless infrastructure networks, certain network
elements, which can be seen as the two endpoints from an O/TWAMP
Pentikousis, et al. Expires November 30, 2015 [Page 2]
Internet-Draft IKEv2-derived Shared Secret Key for O/TWAMP May 2015
perspective, support certificate-based security. For instance,
consider the case in which one wants to measure IP performance
between a E-UTRAN Evolved Node B (eNB) and Security Gateway (SeGW).
Both eNB and SeGW are 3GPP Long Term Evolution (LTE) nodes and
support certificate mode and the Internet Key Exchange Protocol
Version 2 (IKEv2).
The O/TWAMP security mechanism specified in [RFC4656] [RFC5357] only
supports the pre-shared key mode hindering large scale deployment of
O/TWAMP. Furthermore, deployment and management of "shared secrets"
for massive equipment installation consumes a tremendous amount of
effort and is prone to human error. At the same time, recent trends
point to wider Internet Key Exchange Protocol Version 2 (IKEv2)
deployment which, in turn, calls for mechanisms and methods that
enable tunnel end-users, as well as operators, to measure one-way and
two-way network performance in a standardized manner.
With IKEv2 widely deployed, employing shared keys derived from IKEv2
security association (SA) can be considered as a viable alternative
through the method described in this document. If the shared key can
be derived from the IKEv2 SA, O/TWAMP can support certificate-based
key exchange and practically increase operational flexibility and
efficiency. The use of IKEv2 also makes it easier to extend
automatic key management.
In general, O/TWAMP measurement packets can be transmitted inside the
IPsec tunnel, as it occurs with typical user traffic, or transmitted
outside the IPsec tunnel. This may depend on the operator's policy
and the performance evaluation goal, and is orthogonal to the
mechanism described in this document. When IPsec is deployed,
protecting O/TWAMP traffic in unauthenticated mode using IPsec is one
option. Another option is to protect O/TWAMP traffic using the O/
TWAMP layer security established using the Pre-Shared Key (PSK)
derived from IKEv2 but bypassing the IPsec tunnel. Protecting
unauthenticated O/TWAMP control and/or test traffic via
Authentication Header (AH) [RFC4302] or Encapsulating Security
Payload (ESP) [RFC4303] cannot provide various security options,
e.g. it cannot authenticate part of a O/TWAMP packet as mentioned in
[RFC4656].
For measuring latency, a timestamp is carried in O/TWAMP test
traffic. The sender has to fetch the timestamp, encrypt it, and send
it. When the mechanism described in this document is used, partial
authentication of O/TWAMP packets is possible and therefore the
middle step can be skipped, potentially improving accuracy as the
sequence number can be encrypted and authenticated before the
timestamp is fetched. The receiver obtains the timestamp without the
need for the corresponding decryption step. In such cases,
Pentikousis, et al. Expires November 30, 2015 [Page 3]
Internet-Draft IKEv2-derived Shared Secret Key for O/TWAMP May 2015
protecting O/TWAMP traffic using O/TWAMP layer security but bypassing
the IPsec tunnel has its advantages.
This document specifies a method for enabling network measurements
between a TWAMP client and a TWAMP server, as discussed in Section 3.
In short, the shared key used for securing TWAMP traffic is derived
from IKEv2 [RFC7296]. From an operations and management perspective
[RFC5706], the mechanism described in this document requires that
both the TWAMP Control-Client and Server support IPsec.
IKEv2-derived keys SHOULD be used instead of shared secrets when O/
TWAMP is employed in a deployment using IKEv2.
After clarifying the terminology and scope in the subsequent
sections, the remainder of this document is organized as follows.
Section 4 summarizes O/TWAMP protocol operation with respect to
security. Section 5 presents the method for binding TWAMP and IKEv2
for network measurements between the client and the server which both
support IKEv2. Finally, Section 6 discusses the security
considerations arising from the proposed mechanisms.
2. Terminology
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
3. Scope and Applicability
TWAMP implementations signal the use of this method by setting
IKEv2Derived (see Section 7)
Although the control procedures described in this document are
applicable to OWAMP per se, the lack of an established IANA registry
for OWAMP Mode values akin to that listed in Section 7 technically
prevents us from extending OWAMP Mode values. Therefore, independent
OWAMP implementations SHOULD be checked for full compatibility with
respect to the use of this Mode value. Until an IANA registry for
OWAMP Mode values is established, the use of this feature in OWAMP
implementations MUST be arranged privately among consenting OWAMP
users.
4. O/TWAMP Security
Security for O/TWAMP-Control and O/TWAMP-Test are briefly reviewed in
the following subsections.
Pentikousis, et al. Expires November 30, 2015 [Page 4]
Internet-Draft IKEv2-derived Shared Secret Key for O/TWAMP May 2015
4.1. O/TWAMP-Control Security
O/TWAMP uses a simple cryptographic protocol which relies on
o Advanced Encryption Standard (AES) in Cipher Block Chaining (AES-
CBC) for confidentiality
o Hash-based Message Authentication Code (HMAC)-Secure Hash
Algorithm1 (SHA1) truncated to 128 bits for message authentication
Three modes of operation are supported in the OWAMP-Control protocol:
unauthenticated, authenticated, and encrypted. In addition to these
modes, the TWAMP-Control protocol also supports a mixed mode, i.e.
the TWAMP-Control protocol operates in encrypted mode while TWAMP-
Test protocol operates in unauthenticated mode. The authenticated,
encrypted and mixed modes require that endpoints possess a shared
secret, typically a passphrase. The secret key is derived from the
passphrase using a password-based key derivation function PBKDF2
(PKCS#5) [RFC2898].
In the unauthenticated mode, the security parameters are left unused.
In the authenticated, encrypted and mixed modes, the security
parameters are negotiated during the control connection
establishment.
Figure 1 illustrates the initiation stage of the O/TWAMP-Control
protocol between a Control-Client and a Server. In short, the
Control-Client opens a TCP connection to the Server in order to be
able to send O/TWAMP-Control commands. The Server responds with a
Server Greeting, which contains the Modes, Challenge, Salt, Count,
and MBZ fields (see Section 3.1 of [RFC4656]). If the Control-Client
preferred mode is available, the client responds with a Set-Up-
Response message, wherein the selected Mode, as well as the KeyID,
Token and Client initialization vector (IV) are included. The Token
is the concatenation of a 16-octet Challenge, a 16-octet AES Session-
key used for encryption, and a 32-octet HMAC-SHA1 Session-key used
for authentication. The Token is encrypted using AES-CBC.
Pentikousis, et al. Expires November 30, 2015 [Page 5]
Internet-Draft IKEv2-derived Shared Secret Key for O/TWAMP May 2015
+----------------+ +--------+
| Control-Client | | Server |
+----------------+ +--------+
| |
|<------ TCP Connection-- ----->|
| |
|<------ Greeting message ------|
| |
|------- Set-Up-Response ------>|
| |
|<------ Server-Start ----------|
| |
Figure 1: Initiation of O/TWAMP-Control
Encryption uses a key derived from the shared secret associated with
KeyID. In the authenticated, encrypted and mixed modes, all further
communication is encrypted using the AES Session-key and
authenticated with the HMAC Session-key. After receiving the Set-Up-
Response the Server responds with a Server-Start message containing
the Server-IV. The Control-Client encrypts everything it transmits
through the just-established O/TWAMP-Control connection using stream
encryption with Client- IV as the IV. Correspondingly, the Server
encrypts its side of the connection using Server-IV as the IV. The
IVs themselves are transmitted in cleartext. Encryption starts with
the block immediately following that containing the IV.
The AES Session-key and HMAC Session-key are generated randomly by
the Control-Client. The HMAC Session-key is communicated along with
the AES Session-key during O/TWAMP-Control connection setup. The
HMAC Session-key is derived independently of the AES Session-key.
4.2. O/TWAMP-Test Security
The O/TWAMP-Test protocol runs over UDP, using the Session-Sender and
Session-Reflector IP and port numbers that were negotiated during the
Request-Session exchange. O/TWAMP- Test has the same mode with O/
TWAMP-Control and all O/TWAMP-Test sessions inherit the corresponding
O/TWAMP-Control session mode except when operating in mixed mode.
The O/TWAMP-Test packet format is the same in authenticated and
encrypted modes. The encryption and authentication operations are,
however, different. Similarly with the respective O/TWAMP-Control
session, each O/TWAMP-Test session has two keys: an AES Session-key
and an HMAC Session-key. However, there is a difference in how the
keys are obtained:
Pentikousis, et al. Expires November 30, 2015 [Page 6]
Internet-Draft IKEv2-derived Shared Secret Key for O/TWAMP May 2015
O/TWAMP-Control: the keys are generated by the Control-Client and
communicated to the Server during the control connection
establishment with the Set-Up-Response message (as part of
the Token).
O/TWAMP-Test: the keys are derived from the O/TWAMP-Control keys and
the session identifier (SID), which serve as inputs of the
key derivation function (KDF). The O/TWAMP-Test AES Session-
key is generated using the O/TWAMP- Control AES Session-key,
with the 16-octet session identifier (SID), for encrypting
and decrypting the packets of the particular O/TWAMP-Test
session. The O/TWAMP-Test HMAC Session-key is generated
using the O/TWAMP-Control HMAC Session-key, with the 16-octet
session identifier (SID), for authenticating the packets of
the particular O/TWAMP-Test session.
4.3. O/TWAMP Security Root
As discussed above, the AES Session-key and HMAC Session-key used by
the O/TWAMP-Test protocol are derived from the AES Session-key and
HMAC Session-key which are used in the O/TWAMP-Control protocol. The
AES Session-key and HMAC Session-key used in the O/TWAMP-Control
protocol are generated randomly by the Control-Client, and encrypted
with the shared secret associated with KeyID. Therefore, the
security root is the shared secret key. Thus, for large deployments,
key provision and management may become overly complicated.
Comparatively, a certificate-based approach using IKEv2 can
automatically manage the security root and solve this problem, as we
explain in Section 5.
5. O/TWAMP for IPsec Networks
This section presents a method of binding O/TWAMP and IKEv2 for
network measurements between a client and a server which both support
IPsec. In short, the shared key used for securing O/TWAMP traffic is
derived using IKEv2 [RFC7296].
5.1. Shared Key Derivation
In the authenticated, encrypted and mixed modes, the shared secret
key MUST be derived from the IKEv2 Security Association (SA). Note
that we explicitly opt to derive the shared secret key from the IKEv2
SA, rather than the child SA, since the use case whereby an IKEv2 SA
can be created without generating any child SA is possible [RFC6023].
When the shared secret key is derived from the IKEv2 SA, SK_d must be
generated first. SK_d must be computed as per [RFC7296].
Pentikousis, et al. Expires November 30, 2015 [Page 7]
Internet-Draft IKEv2-derived Shared Secret Key for O/TWAMP May 2015
The shared secret key MUST be generated as follows:
Shared secret key = prf( SK_d, "IPPM" )
Wherein the string "IPPM" is encoded in ASCII and "prf" is a
pseudorandom function.
It is recommended that the shared secret key is derived in the IPsec
layer so that IPsec keying material is not exposed to the O/TWAMP
client. Note, however, that the interaction between the O/TWAMP and
IPsec layers is host-internal and implementation-specific.
Therefore, this is clearly outside the scope of this document, which
focuses on the interaction between the O/TWAMP client and server.
That said, one possible way could be the following: at the Control-
Client side, the IPSec layer can perform a lookup in the Security
Association Database (SAD) using the IP address of the Server and
thus match the corresponding IKEv2 SA. At the Server side, the IPSec
layer can look up the corresponding IKEv2 SA by using the Security
Parameter Indexes (SPIs) sent by the Control-Client (see
Section 5.3), and therefore extract the shared secret key.
In case that both client and server do support IKEv2 but there is no
current IKEv2 SA, two alternative ways could be considered. First,
the O/TWAMP Control-Client initiates the establishment of the IKEv2
SA, logs this operation, and selects the mode which supports IKEv2.
Alternatively, the O/TWAMP Control-Client does not initiate the
establishment of the IKEv2 SA, logs an error for operational
management purposes, and proceeds with the modes defined in
[RFC4656][RFC5357][RFC5618]. Again, although both alternatives are
feasible, they are in fact implementation-specific.
If rekeying for the IKEv2 SA or deletion of the IKEv2 SA occurs, the
corresponding shared secret key generated from the SA MUST continue
to be used until the O/TWAMP session terminates.
5.2. Server Greeting Message Update
To trigger a binding association between the key generated from IKEv2
and the O/TWAMP shared secret key, the Modes field in the Server
Greeting Message (Figure 2) will need to allow for support of key
derivation as discussed in Section 5.1. Therefore, when this method
is used, the Modes value extension MUST be supported. Support for
deriving the shared key from the IKEv2 SA is indicated by setting
IKEv2Derived (see Section 7).
Pentikousis, et al. Expires November 30, 2015 [Page 8]
Internet-Draft IKEv2-derived Shared Secret Key for O/TWAMP May 2015
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
| Unused (12 octets) |
| |
|+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-++-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Modes |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
| Challenge (16 octets) |
| |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
| Salt (16 octets) |
| |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Count (4 octets) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
| MBZ (12 octets) |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 2: Server Greeting format
The choice of this set of Modes values poses no backwards
compatibility problems to existing O/TWAMP clients. Robust legacy
Control-Client implementations would disregard the fact that the
IKEv2Derived Modes bit in the Server Greeting is set. On the other
hand, a Control-Client implementing this method can identify that the
O/TWAMP Server contacted does not support this specification. If the
Server supports other Modes, as one could assume, the Control-Client
would then decide which Mode to use and indicate such accordingly as
per [RFC4656][RFC5357]. A Control-Client implementing this method
which decides not to employ IKEv2 derivation, can simply behave as a
purely [RFC4656]/[RFC5357] compatible client.
5.3. Set-Up-Response Update
The Set-Up-Response Message Figure 3 is updated as follows. When a
O/TWAMP Control-Client implementing this method receives a Server
Greeting indicating support for Mode IKEv2Derived it SHOULD reply to
the O/TWAMP Server with a Set-Up response that indicates so. For
example, a compatible O/TWAMP Control-Client choosing the
authenticated mode with IKEv2 shared secret key derivation should set
Pentikousis, et al. Expires November 30, 2015 [Page 9]
Internet-Draft IKEv2-derived Shared Secret Key for O/TWAMP May 2015
Mode to 130, i.e. set the bits in positions 1 and 7 to one (see
Section 7).
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Mode |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
| Key ID (80 octets) |
| |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
| Token (16 octets) |
| |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
| Client-IV (12 octets) |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 3: Set-Up-Response Message
The Security Parameter Index (SPI)(see [RFC4301] [RFC7296]) uniquely
identifies the Security Association (SA). If the Control-Client
supports the derivation of shared secret key from IKEv2 SA, it will
choose the corresponding mode value and carry SPIi and SPIr in the
Key ID field. SPIi and SPIr MUST be included in the Key ID field of
the Set-Up-Response Message to indicate the IKEv2 SA from which the
O/TWAMP shared secret key derived from. The length of SPI is 8
octets. Therefore, the first 8 octets of Key ID field MUST carry
SPIi and the second 8 octets MUST carry SPIr. The remaining bits of
the Key ID field MUST be set to zero.
A O/TWAMP Server implementation of this method, MUST obtain the SPIi
and SPIr from the first 16 octets and ignore the remaining octets of
the Key ID field. Then, the Control-Client and the Server can derive
the shared secret key based on the Mode value and SPI. If the O/
TWAMP Server cannot find the IKEv2 SA corresponding to the SPIi and
SPIr received, it MUST log the event for operational management
purposes. In addition, the O/TWAMP Server SHOULD set the Accept
field of the Server-Start message to the value 6 to indicate that the
Server is not willing to conduct further transactions in this O/
TWAMP-Control session since it can not find the corresponding IKEv2
SA.
Pentikousis, et al. Expires November 30, 2015 [Page 10]
Internet-Draft IKEv2-derived Shared Secret Key for O/TWAMP May 2015
5.4. O/TWAMP over an IPsec tunnel
IPsec Authentication Header (AH) [RFC4302] and Encapsulating Security
Payload (ESP) [RFC4303] provide confidentiality and data integrity to
IP datagrams. An IPsec tunnel can be used to provide the protection
needed for O/TWAMP Control and Test packets, even if the peers choose
the unauthenticated mode of operation. In order to ensure
authenticity and security, O/TWAMP packets between two IKEv2 systems
SHOULD be configured to use the corresponding IPsec tunnel running
over an external network even when using the O/TWAMP unauthenticated
mode.
6. Security Considerations
As the shared secret key is derived from the IKEv2 SA, the key
derivation algorithm strength and limitations are as per [RFC7296].
The strength of a key derived from a Diffie-Hellman exchange using
any of the groups defined here depends on the inherent strength of
the group, the size of the exponent used, and the entropy provided by
the random number generator employed. The strength of all keys and
implementation vulnerabilities, particularly Denial of Service (DoS)
attacks are as defined in [RFC7296].
7. IANA Considerations
During the production of this document, the authors and reviewers
noticed that the TWAMP-Modes registry, which should describe a
bitfield of flags, instead is defined as a registry of integer
values. In addition, the Semantics Definition column seems to have
spurious information in it. The registry should be changed to
correct these issues, as follows:
Bit|Description |Semantics |Reference|
| |Definition | |
---|-------------------------------------------|------------|---------|
0 Unauthenticated Section 3.1 [RFC4656]
1 Authenticated Section 3.1 [RFC4656]
2 Encrypted Section 3.1 [RFC4656]
3 Unauth.TEST protocol,Encrypted CONTROL Section 3.1 [RFC5618]
4 Individual Session Control [RFC5938]
5 Reflect Octets Capability [RFC6038]
6 Symmetrical Size Sender Test Packet Format [RFC6038]
Figure 4: TWAMP Modes registry
Pentikousis, et al. Expires November 30, 2015 [Page 11]
Internet-Draft IKEv2-derived Shared Secret Key for O/TWAMP May 2015
In addition, this document adds a new entry to this registry:
Bit|Description |Semantics |Reference|
| |Definition | |
---|-------------------------------------------|------------|---------|
7 IKEv2Derived Mode Capability Section 5 [RFCxxxx]
(where RFCxxxx refers to draft-ietf-ippm-ipsec).
Figure 5: IKEv2 Derived Mode Capability
8. Acknowledgments
We thank Eric Chen, Yaakov Stein, Brian Trammell, Emily Bi, John
Mattsson, Steve Baillargeon, Spencer Dawkins, Tero Kivinen, Fred
Baker, Meral Shirazipour, Hannes Tschofenig, Ben Campbell, Stephen
Farrell, Brian Haberman, and Barry Leiba for their reviews, comments
and text suggestions.
Al Morton deserves a special mention for his thorough reviews and
text contributions to this document as well as the constructive
discussions over several IPPM meetings.
9. References
9.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC4302] Kent, S., "IP Authentication Header", RFC 4302, December
2005.
[RFC4303] Kent, S., "IP Encapsulating Security Payload (ESP)", RFC
4303, December 2005.
[RFC4656] Shalunov, S., Teitelbaum, B., Karp, A., Boote, J., and M.
Zekauskas, "A One-way Active Measurement Protocol
(OWAMP)", RFC 4656, September 2006.
[RFC5357] Hedayat, K., Krzanowski, R., Morton, A., Yum, K., and J.
Babiarz, "A Two-Way Active Measurement Protocol (TWAMP)",
RFC 5357, October 2008.
Pentikousis, et al. Expires November 30, 2015 [Page 12]
Internet-Draft IKEv2-derived Shared Secret Key for O/TWAMP May 2015
[RFC5618] Morton, A. and K. Hedayat, "Mixed Security Mode for the
Two-Way Active Measurement Protocol (TWAMP)", RFC 5618,
August 2009.
[RFC7296] Kaufman, C., Hoffman, P., Nir, Y., Eronen, P., and T.
Kivinen, "Internet Key Exchange Protocol Version 2
(IKEv2)", STD 79, RFC 7296, October 2014.
9.2. Informative References
[RFC2898] Kaliski, B., "PKCS #5: Password-Based Cryptography
Specification Version 2.0", RFC 2898, September 2000.
[RFC4301] Kent, S. and K. Seo, "Security Architecture for the
Internet Protocol", RFC 4301, December 2005.
[RFC5706] Harrington, D., "Guidelines for Considering Operations and
Management of New Protocols and Protocol Extensions", RFC
5706, November 2009.
[RFC6023] Nir, Y., Tschofenig, H., Deng, H., and R. Singh, "A
Childless Initiation of the Internet Key Exchange Version
2 (IKEv2) Security Association (SA)", RFC 6023, October
2010.
Authors' Addresses
Kostas Pentikousis (editor)
EICT GmbH
EUREF-Campus Haus 13
Torgauer Strasse 12-15
10829 Berlin
Germany
Email: k.pentikousis@eict.de
Emma Zhang
Huawei Technologies
Huawei Building, No.3, Rd. XinXi
Haidian District , Beijing 100095
P. R. China
Email: emma.zhanglijia@huawei.com
Pentikousis, et al. Expires November 30, 2015 [Page 13]
Internet-Draft IKEv2-derived Shared Secret Key for O/TWAMP May 2015
Yang Cui
Huawei Technologies
Otemachi First Square 1-5-1 Otemachi
Chiyoda-ku, Tokyo 100-0004
Japan
Email: cuiyang@huawei.com
Pentikousis, et al. Expires November 30, 2015 [Page 14]