Network Working Group                                    A. Sajassi, Ed.
INTERNET-DRAFT                                                     Cisco
Category: Standards Track
                                                             R. Aggarwal
J. Drake                                                          Arktan
Juniper Networks
                                                                N. Bitar
W. Henderickx                                                    Verizon
Alcatel-Lucent
                                                            Aldrin Isaac
                                                               Bloomberg

                                                               J. Uttaro
                                                                    AT&T

Expires: September 12, 2014                               March 12, 2014


                      BGP MPLS Based Ethernet VPN
                        draft-ietf-l2vpn-evpn-06

Status of this Memo

   This Internet-Draft is submitted to IETF in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF), its areas, and its working groups.  Note that
   other groups may also distribute working documents as
   Internet-Drafts.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   The list of current Internet-Drafts can be accessed at
   http://www.ietf.org/1id-abstracts.html

   The list of Internet-Draft Shadow Directories can be accessed at
   http://www.ietf.org/shadow.html


Copyright and License Notice

   Copyright (c) 2013 IETF Trust and the persons identified as the
   document authors. All rights reserved.




Sajassi, et al.        Expires September 12, 2014               [Page 1]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document. Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document. Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Abstract

   This document describes procedures for BGP MPLS based Ethernet VPNs
   (EVPN).

Table of Contents

   1. Specification of requirements . . . . . . . . . . . . . . . . .  5
   2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . .  5
   3. Introduction  . . . . . . . . . . . . . . . . . . . . . . . . .  6
   4. BGP MPLS Based EVPN Overview  . . . . . . . . . . . . . . . . .  6
   5. Ethernet Segment  . . . . . . . . . . . . . . . . . . . . . . .  7
   6. Ethernet Tag  . . . . . . . . . . . . . . . . . . . . . . . . . 10
     6.1 VLAN Based Service Interface . . . . . . . . . . . . . . . . 10
     6.2 VLAN Bundle Service Interface  . . . . . . . . . . . . . . . 11
       6.2.1 Port Based Service Interface . . . . . . . . . . . . . . 11
     6.3 VLAN Aware Bundle Service Interface  . . . . . . . . . . . . 11
       6.3.1 Port Based VLAN Aware Service Interface  . . . . . . . . 11
   7. BGP EVPN NLRI . . . . . . . . . . . . . . . . . . . . . . . . . 12
     7.1. Ethernet Auto-Discovery Route . . . . . . . . . . . . . . . 12
     7.2.  MAC/IP Advertisement Route . . . . . . . . . . . . . . . . 13
     7.3. Inclusive Multicast Ethernet Tag Route  . . . . . . . . . . 14
     7.4 Ethernet Segment Route . . . . . . . . . . . . . . . . . . . 14
     7.5 ESI Label Extended Community . . . . . . . . . . . . . . . . 15
     7.6 ES-Import Route Target . . . . . . . . . . . . . . . . . . . 15
     7.7 MAC Mobility Extended Community  . . . . . . . . . . . . . . 16
     7.8 Default Gateway Extended Community . . . . . . . . . . . . . 16
   8. Multi-homing Functions  . . . . . . . . . . . . . . . . . . . . 16
     8.1 Multi-homed Ethernet Segment Auto-Discovery  . . . . . . . . 17
       8.1.1 Constructing the Ethernet Segment Route  . . . . . . . . 17
     8.2 Fast Convergence . . . . . . . . . . . . . . . . . . . . . . 17
       8.2.1 Constructing the Ethernet A-D per Ethernet Segment
             (ES) Route . . . . . . . . . . . . . . . . . . . . . . . 18
         8.2.1.1. Ethernet A-D Route Targets  . . . . . . . . . . . . 18
     8.3 Split Horizon  . . . . . . . . . . . . . . . . . . . . . . . 19
       8.3.1 ESI Label Assignment . . . . . . . . . . . . . . . . . . 19
         8.3.1.1 Ingress Replication  . . . . . . . . . . . . . . . . 19
         8.3.1.2. P2MP MPLS LSPs  . . . . . . . . . . . . . . . . . . 20



Sajassi, et al.        Expires September 12, 2014               [Page 2]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


     8.4 Aliasing and Backup-Path . . . . . . . . . . . . . . . . . . 21
       8.4.1 Constructing the Ethernet A-D per EVPN Instance (EVI)
             Route  . . . . . . . . . . . . . . . . . . . . . . . . . 22
         8.4.1.1 Ethernet A-D Route Targets . . . . . . . . . . . . . 23
     8.5 Designated Forwarder Election  . . . . . . . . . . . . . . . 24
     8.6. Interoperability with Single-homing PEs . . . . . . . . . . 26
   9. Determining Reachability to Unicast MAC Addresses . . . . . . . 26
     9.1. Local Learning  . . . . . . . . . . . . . . . . . . . . . . 27
     9.2. Remote learning . . . . . . . . . . . . . . . . . . . . . . 27
       9.2.1. Constructing the BGP EVPN MAC/IP Address
              Advertisement . . . . . . . . . . . . . . . . . . . . . 27
       9.2.2 Route Resolution . . . . . . . . . . . . . . . . . . . . 29
   10. ARP and ND . . . . . . . . . . . . . . . . . . . . . . . . . . 30
     10.1 Default Gateway . . . . . . . . . . . . . . . . . . . . . . 31
   11. Handling of Multi-Destination Traffic  . . . . . . . . . . . . 32
     11.1. Construction of the Inclusive Multicast Ethernet Tag
           Route  . . . . . . . . . . . . . . . . . . . . . . . . . . 32
     11.2. P-Tunnel Identification  . . . . . . . . . . . . . . . . . 33
   12. Processing of Unknown Unicast Packets  . . . . . . . . . . . . 34
     12.1. Ingress Replication  . . . . . . . . . . . . . . . . . . . 34
     12.2. P2MP MPLS LSPs . . . . . . . . . . . . . . . . . . . . . . 35
   13. Forwarding Unicast Packets . . . . . . . . . . . . . . . . . . 35
     13.1. Forwarding packets received from a CE  . . . . . . . . . . 35
     13.2. Forwarding packets received from a remote PE . . . . . . . 36
       13.2.1. Unknown Unicast Forwarding . . . . . . . . . . . . . . 36
       13.2.2. Known Unicast Forwarding . . . . . . . . . . . . . . . 37
   14. Load Balancing of Unicast Frames . . . . . . . . . . . . . . . 37
     14.1. Load balancing of traffic from an PE to remote CEs . . . . 37
       14.1.1 Single-Active Redundancy Mode . . . . . . . . . . . . . 37
       14.1.2 All-Active Redundancy Mode  . . . . . . . . . . . . . . 38
     14.2. Load balancing of traffic between an PE and a local CE . . 40
       14.2.1. Data plane learning  . . . . . . . . . . . . . . . . . 40
       14.2.2. Control plane learning . . . . . . . . . . . . . . . . 40
   15. MAC Mobility . . . . . . . . . . . . . . . . . . . . . . . . . 40
     15.1. MAC Duplication Issue  . . . . . . . . . . . . . . . . . . 42
     15.2. Sticky MAC addresses . . . . . . . . . . . . . . . . . . . 43
   16. Multicast & Broadcast  . . . . . . . . . . . . . . . . . . . . 43
     16.1. Ingress Replication  . . . . . . . . . . . . . . . . . . . 43
     16.2. P2MP LSPs  . . . . . . . . . . . . . . . . . . . . . . . . 43
       16.2.1. Inclusive Trees  . . . . . . . . . . . . . . . . . . . 43
   17. Convergence  . . . . . . . . . . . . . . . . . . . . . . . . . 44
     17.1. Transit Link and Node Failures between PEs . . . . . . . . 44
     17.2. PE Failures  . . . . . . . . . . . . . . . . . . . . . . . 44
     17.3. PE to CE Network Failures  . . . . . . . . . . . . . . . . 44
   18. Frame Ordering . . . . . . . . . . . . . . . . . . . . . . . . 45
   19. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 46
   20. Security Considerations  . . . . . . . . . . . . . . . . . . . 46
   21. Co-authors . . . . . . . . . . . . . . . . . . . . . . . . . . 47



Sajassi, et al.        Expires September 12, 2014               [Page 3]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


   22.  IANA Considerations . . . . . . . . . . . . . . . . . . . . . 48
   23. References . . . . . . . . . . . . . . . . . . . . . . . . . . 48
     23.1 Normative References  . . . . . . . . . . . . . . . . . . . 48
     23.2 Informative References  . . . . . . . . . . . . . . . . . . 48
   24. Author's Address . . . . . . . . . . . . . . . . . . . . . . . 49














































Sajassi, et al.        Expires September 12, 2014               [Page 4]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


1. Specification of requirements

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in [RFC2119].


2. Terminology

   Bridge Domain:

   Broadcast Domain:

   CE: Customer Edge device e.g., host or router or switch

   EVI:  An EVPN instance spanning across the PEs participating in that
   VPN

   MAC-VRF:  A Virtual Routing and Forwarding table for MAC addresses on
   a PE for an EVI

   Ethernet Segment Identifier (ESI):  If a CE is multi-homed to two or
   more PEs, the set of Ethernet links that attaches the CE to the PEs
   is an 'Ethernet segment'.   Ethernet segments MUST have a unique non-
   zero identifier, the 'Ethernet Segment Identifier'.

   Ethernet Tag:  An Ethernet Tag identifies a particular broadcast
   domain, e.g., a VLAN.  An EVPN instance consists of one or more
   broadcast domains. Ethernet tag(s) are assigned to the broadcast
   domains of a given EVPN instance by the provider of that EVPN, and
   each PE in that EVPN instance performs a mapping between broadcast
   domain identifier(s) understood by each of its attached CEs and the
   corresponding Ethernet tag.

   LACP: Link Aggregation Control Protocol

   MP2MP: Multipoint to Multipoint

   P2MP: Point to Multipoint

   P2P: Point to Point

   Single-Active Redundancy Mode: When only a single PE, among a group
   of PEs attached to an Ethernet segment, is allowed to forward traffic
   to/from that Ethernet Segment, then the Ethernet segment is defined
   to be operating in Single-Active redundancy mode.

   All-Active Redundancy Mode: When all PEs attached to an Ethernet



Sajassi, et al.        Expires September 12, 2014               [Page 5]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


   segment are allowed to forward traffic to/from that Ethernet Segment,
   then the Ethernet segment is defined to be operating in All-Active
   redundancy mode.


3. Introduction

   This document describes procedures for BGP MPLS based Ethernet VPNs
   (EVPN).  The procedures described here are intended to meet the
   requirements specified in [EVPN-REQ].  Please refer to [EVPN-REQ] for
   the detailed requirements and motivation. EVPN requires extensions to
   existing IP/MPLS protocols as described in this document. In addition
   to these extensions EVPN uses several building blocks from existing
   MPLS technologies.


4. BGP MPLS Based EVPN Overview

   This section provides an overview of EVPN. An EVPN instance comprises
   CEs that are connected to PEs that form the edge of the MPLS
   infrastructure. A CE may be a host, a router or a switch. The PEs
   provide virtual Layer 2 bridged connectivity between the CEs. There
   may be multiple EVPN instances in the provider's network.

   The PEs may be connected by an MPLS LSP infrastructure which provides
   the benefits of MPLS technology such as fast-reroute, resiliency,
   etc.  The PEs may also be connected by an IP infrastructure in which
   case IP/GRE tunneling or other IP tunneling can be used between the
   PEs. The detailed procedures in this version of this document are
   specified only for MPLS LSPs as the tunneling technology. However
   these procedures are designed to be extensible to IP tunneling as the
   PSN tunneling technology.

   In an EVPN, MAC learning between PEs occurs not in the data plane (as
   happens with traditional bridging) but in the control plane. Control
   plane learning offers greater control over the MAC learning process,
   such as restricting who learns what, and the ability to apply
   policies.  Furthermore, the control plane chosen for advertising MAC
   reachability information is multi-protocol (MP) BGP (similar to IP
   VPNs (RFC 4364)). This provides greater scalability and the ability
   to preserve the "virtualization" or isolation of groups of
   interacting agents (hosts, servers, virtual machines) from each
   other. In EVPN, PEs advertise the MAC addresses learned from the CEs
   that are connected to them, along with an MPLS label, to other PEs in
   the control plane using MP-BGP. Control plane learning enables load
   balancing of traffic to and from CEs that are multi-homed to multiple
   PEs. This is in addition to load balancing across the MPLS core via
   multiple LSPs between the same pair of PEs.  In other words it allows



Sajassi, et al.        Expires September 12, 2014               [Page 6]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


   CEs to connect to multiple active points of attachment. It also
   improves convergence times in the event of certain network failures.

   However, learning between PEs and CEs is done by the method best
   suited to the CE: data plane learning, IEEE 802.1x, LLDP, 802.1aq,
   ARP, management plane or other protocols.

   It is a local decision as to whether the Layer 2 forwarding table on
   an PE is populated with all the MAC destination addresses known to
   the control plane, or whether the PE implements a cache based scheme.
   For instance the MAC forwarding table may be populated only with the
   MAC destinations of the active flows transiting a specific PE.

   The policy attributes of EVPN are very similar to those of IP-VPN. A
   EVPN instance requires a Route-Distinguisher (RD) which is unique per
   PE and one or more globally unique Route-Targets (RTs). A CE attaches
   to a MAC-VRF on an PE, on an Ethernet interface which may be
   configured for one or more Ethernet Tags, e.g., VLAN IDs. Some
   deployment scenarios guarantee uniqueness of VLAN IDs across EVPN
   instances: all points of attachment for a given EVPN instance use the
   same VLAN ID, and no other EVPN instance uses this VLAN ID.  This
   document refers to this case as a "Unique VLAN EVPN" and describes
   simplified procedures to optimize for it.


5. Ethernet Segment

   If a CE is multi-homed to two or more PEs, the set of Ethernet links
   constitutes an "Ethernet Segment". An Ethernet segment may appear to
   the CE as a Link Aggregation Group (LAG).  Ethernet segments have an
   identifier, called the "Ethernet Segment Identifier" (ESI) which is
   encoded as a ten octets integer.  The following two ESI values are
   reserved:

      - ESI 0 denotes a single-homed CE.

      - ESI {0xFF} (repeated 10 times) is known as MAX-ESI and is
   reserved.

   In general, an Ethernet segment MUST have a non-reserved ESI that is
   unique network wide (e.g., across all EVPN instances on all the PEs).
   If the CE(s) constituting an Ethernet Segment is (are) managed by the
   network operator, then ESI uniqueness should be guaranteed; however,
   if the CE(s) is (are) not managed, then the operator MUST configure a
   network-wide unique ESI for that Ethernet Segment.  This is required
   to enable auto-discovery of Ethernet Segments and DF election.

   In a network with managed and not-managed CEs, the ESI has the



Sajassi, et al.        Expires September 12, 2014               [Page 7]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


   following format:

         +---+---+---+---+---+---+---+---+---+---+
         | T |          ESI Value                |
         +---+---+---+---+---+---+---+---+---+---+

   Where:

   T (ESI Type) is a 1-byte field (most significant octet) that
   specifies the format of the remaining nine bytes (ESI Value). The
   following 6 ESI types can be used:

   - Type 0 (T=0x00) - This type indicates an arbitrary nine-octet ESI
   value, which is managed and configured by the operator.

   - Type 1 (T=0x01) - When IEEE 802.1AX LACP is used between the PEs
   and CEs, this ESI type indicates an auto-generated ESI value
   determined from LACP by concatenating the following parameters:

        + CE LACP six octets System MAC address. The CE LACP System MAC
          address MUST be encoded in the high order six octets of the ESI
          Value field.

        + CE LACP two octets Port Key. The CE LACP port key MUST be
          encoded in the two octets next to the System MAC address.

        + The remaining octet will be set to 0x00.

        As far as the CE is concerned, it would treat the multiple PEs
        that it is connected to as the same switch. This allows the CE
        to aggregate links that are attached to different PEs in the
        same bundle.

        This mechanism could be used only if it produces ESIs that satisfy
        the uniqueness requirement specified above.

   - Type 2 (T=0x02) - This type is used in the case of indirectly
   connected hosts via a bridged LAN between the CEs and the PEs. The
   ESI Value is auto-generated and determined based on the Layer 2
   bridge protocol as follows: If MST is used in the bridged LAN then
   the value of the ESI is derived by listening to BPDUs on the Ethernet
   segment. To achieve this the PE is not required to run MST. However
   the PE must learn the Root Bridge MAC address and Bridge Priority of
   the root of the Internal Spanning Tree (IST) by listening to the
   BPDUs. The ESI Value is constructed as follows:

        + Root Bridge six octets MAC address. The Root Bridge MAC
          address MUST be encoded in the high order six octets of the



Sajassi, et al.        Expires September 12, 2014               [Page 8]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


          ESI Value field.

        + Root Bridge two octets Priority. The CE LACP port key MUST be
          encoded in the two octets next to the Root Bridge MAC address.

        + The remaining octet will be set to 0x00.

        This mechanism could be used only if it produces ESIs that satisfy
        the uniqueness requirement specified above.

   - Type 3 (T=0x03) - This type indicates a MAC-based ESI Value that
   can be auto-generated or configured by the operator. The ESI Value is
   constructed as follows:

        + System MAC address (six octets). The System MAC address MUST
          be encoded in the high order six octets of the ESI Value field.

        + Local Discriminator value (three octets). The Local
          Discriminator MUST be encoded in the low order three octets
          of the ESI Value.

        This mechanism could be used only if it produces ESIs that satisfy
        the uniqueness requirement specified above.

   - Type 4 (T=0x04) - This type indicates an IP-based ESI Value that
   can be auto-generated or configured by the operator. The ESI Value is
   constructed as follows:

        + IP address (four octets). This is an IPv4 address owned by
          the system and MUST be encoded in the high order four octets
          of the ESI Value field.

        + Local Discriminator value (four octets). The Local Discriminator
          MUST be encoded in the four octets next to the IP address.

        + The low order octet of the ESI Value will be set to 0x00.

        This mechanism could be used only if it produces ESIs that satisfy
        the uniqueness requirement specified above.

   - Type 5 (T=0x05) - This type indicates an AS-based ESI Value that
   can be auto-generated or configured by the operator. The ESI Value is
   constructed as follows:

        + AS number (four octets). This is an AS number owned by the
         system and MUST be encoded in the high order four octets of the
         ESI Value field. If a two-octet AS number is used, the high order
         extra two bytes will be 0x0000.



Sajassi, et al.        Expires September 12, 2014               [Page 9]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


        + Local Discriminator value (four octets). The Local Discriminator
          MUST be encoded in the four octets next to the AS number.

        + The low order octet of the ESI Value will be set to 0x00.

        This mechanism could be used only if it produces ESIs that satisfy
        the uniqueness requirement specified above.


6. Ethernet Tag

   An Ethernet Tag identifies a particular broadcast domain, e.g. a
   VLAN, in an EVPN Instance.  An EVPN Instance consists of one or more
   broadcast domains (one or more VLANs). VLANs are assigned to a given
   EVPN Instance by the provider of the EVPN service. A given VLAN can
   itself be represented by multiple VLAN IDs (VIDs). In such cases, the
   PEs participating in that VLAN for a given EVPN instance are
   responsible for performing VLAN ID translation to/from locally
   attached CE devices.

   If a VLAN is represented by a single VID across all PE devices
   participating in that VLAN for that EVPN instance, then there is no
   need for VID translation at the PEs. Furthermore, some deployment
   scenarios guarantee uniqueness of VIDs across all EVPN instances;
   all points of attachment for a given EVPN instance use the same VID
   and no other EVPN instances use that VID.  This allows the RT(s) for
   each EVPN instance to be derived automatically from the corresponding
   VID, as described in section 8.4.1.1.1 "Auto-Derivation from the
   Ethernet Tag ID".

   The following subsections discuss the relationship between broadcast
   domains (e.g., VLANs), Ethernet Tags (e.g., VIDs), and MAC-VRFs as
   well as the setting of the Ethernet Tag Identifier, in the various
   EVPN BGP routes (defined in section 8), for the different types of
   service interfaces described in [EVPN-REQ].

   The following Ethernet Tag value is reserved:

      - Ethernet Tag {0xFFFFFFFF} is known as MAX-ET

6.1 VLAN Based Service Interface

   With this service interface, an EVPN instance consists of only a
   single broadcast domain (e.g., a single VLAN). Therefore, there is a
   one to one mapping between a VID on this interface and a MAC-VRF.
   Since a MAC-VRF corresponds to a single VLAN, it consists of a single
   bridge domain corresponding to that VLAN. If the VLAN is represented
   by different VIDs on different PEs, then each PE needs to perform VID



Sajassi, et al.        Expires September 12, 2014              [Page 10]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


   translation for frames destined to its attached CEs. In such
   scenarios, the Ethernet frames transported over MPLS/IP network
   SHOULD remain tagged with the originating VID and a VID translation
   MUST be supported in the data path and MUST be performed on the
   disposition PE. The Ethernet Tag Identifier in all EVPN routes MUST
   be set to 0.

6.2 VLAN Bundle Service Interface

   With this service interface, an EVPN instance corresponds to several
   broadcast domains (e.g., several VLANs); however, only a single
   bridge domain is maintained per MAC-VRF which means multiple VLANs
   share the same bridge domain. This implies MAC addresses MUST be
   unique across different VLANs for this service to work. In other
   words, there is a many-to-one mapping between VLANs and a MAC-VRF,
   and the MAC-VRF consists of a single bridge domain. Furthermore, a
   single VLAN must be represented by a single VID - e.g., no VID
   translation is allowed for this service interface type. The MPLS
   encapsulated frames MUST remain tagged with the originating VID. Tag
   translation is NOT permitted. The Ethernet Tag Identifier in all EVPN
   routes MUST be set to 0.

6.2.1 Port Based Service Interface

   This service interface is a special case of the VLAN Bundle service
   interface, where all of the VLANs on the port are part of the same
   service and map to the same bundle. The procedures are identical to
   those described in section 6.2.

6.3 VLAN Aware Bundle Service Interface

   With this service interface, an EVPN instance consists of several
   broadcast domains (e.g., several VLANs) with each VLAN having its own
   bridge domain - e.g., multiple bridge domains (one per VLAN) is
   maintained by a single MAC-VRF corresponding to the EVPN instance. In
   the case where a single VLAN is represented by different VIDs on
   different CEs and thus tag (VID) translation is required, a
   normalized Ethernet Tag (VID) MUST be carried in the MPLS
   encapsulated frames and a tag translation function MUST be supported
   in the data path. This translation MUST be performed in data path on
   both the imposition as well as the disposition PEs (translating to
   normalized tag on imposition PE and translating to local tag on
   disposition PE). The Ethernet Tag Identifier in all EVPN routes MUST
   be set to the normalized Ethernet Tag assigned by the EVPN provider.

6.3.1 Port Based VLAN Aware Service Interface

   This service interface is a special case of the VLAN Aware Bundle



Sajassi, et al.        Expires September 12, 2014              [Page 11]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


   service interface, where all of the VLANs on the port are part of the
   same service and map to the same bundle. The procedures are identical
   to those described in section 6.3.

7. BGP EVPN NLRI

   This document defines a new BGP NLRI, called the EVPN NLRI.

   Following is the format of the EVPN NLRI:

                   +-----------------------------------+
                   |    Route Type (1 octet)           |
                   +-----------------------------------+
                   |     Length (1 octet)              |
                   +-----------------------------------+
                   | Route Type specific (variable)    |
                   +-----------------------------------+

   The Route Type field defines encoding of the rest of the EVPN NLRI
   (Route Type specific EVPN NLRI).

   The Length field indicates the length in octets of the Route Type
   specific field of EVPN NLRI.

   This document defines the following Route Types:

        + 1 - Ethernet Auto-Discovery (A-D) route
        + 2 - MAC advertisement route
        + 3 - Inclusive Multicast Route
        + 4 - Ethernet Segment Route

   The detailed encoding and procedures for these route types are
   described in subsequent sections.

   The EVPN NLRI is carried in BGP [RFC4271] using BGP Multiprotocol
   Extensions [RFC4760] with an AFI of 25 (L2VPN) and a SAFI of 70
   (EVPN). The NLRI field in the MP_REACH_NLRI/MP_UNREACH_NLRI attribute
   contains the EVPN NLRI (encoded as specified above).

   In order for two BGP speakers to exchange labeled EVPN NLRI, they
   must use BGP Capabilities Advertisement to ensure that they both are
   capable of properly processing such NLRI. This is done as specified
   in [RFC4760], by using capability code 1 (multiprotocol BGP) with an
   AFI of 25 (L2VPN) and a SAFI of 70 (EVPN).

7.1. Ethernet Auto-Discovery Route

   A Ethernet A-D route type specific EVPN NLRI consists of the



Sajassi, et al.        Expires September 12, 2014              [Page 12]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


   following:

                   +---------------------------------------+
                   |      RD   (8 octets)                  |
                   +---------------------------------------+
                   |Ethernet Segment Identifier (10 octets)|
                   +---------------------------------------+
                   |  Ethernet Tag ID (4 octets)           |
                   +---------------------------------------+
                   |  MPLS Label (3 octets)                |
                   +---------------------------------------+

   For the purpose of BGP route key processing, only the Ethernet
   Segment ID and the Ethernet Tag ID are considered to be part of the
   prefix in the NLRI.   The MPLS Label field is to be treated as a
   route attribute as opposed to being part of the route.

   For procedures and usage of this route please see section 8.2 "Fast
   Convergence" and section 8.4 "Aliasing".

7.2.  MAC/IP Advertisement Route

   A MAC advertisement route type specific EVPN NLRI consists of the
   following:

                   +---------------------------------------+
                   |      RD   (8 octets)                  |
                   +---------------------------------------+
                   |Ethernet Segment Identifier (10 octets)|
                   +---------------------------------------+
                   |  Ethernet Tag ID (4 octets)           |
                   +---------------------------------------+
                   |  MAC Address Length (1 octet)         |
                   +---------------------------------------+
                   |  MAC Address (6 octets)               |
                   +---------------------------------------+
                   |  IP Address Length (1 octet)          |
                   +---------------------------------------+
                   |  IP Address (0 or 4 or 16 octets)     |
                   +---------------------------------------+
                   |  MPLS Label1 (3 octets)               |
                   +---------------------------------------+
                   |  MPLS Label2 (0 or 3 octets)          |
                   +---------------------------------------+


   For the purpose of BGP route key processing, only the Ethernet Tag
   ID, MAC Address Length, MAC Address, IP Address Length, and IP



Sajassi, et al.        Expires September 12, 2014              [Page 13]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


   Address Address fields are considered to be part of the prefix in the
   NLRI. The Ethernet Segment Identifier and MPLS Label fields are to be
   treated as route attributes as opposed to being part of the "route".

   For procedures and usage of this route please see section 9
   "Determining Reachability to Unicast MAC Addresses" and section 14
   "Load Balancing of Unicast Packets".

7.3. Inclusive Multicast Ethernet Tag Route

   An Inclusive Multicast Ethernet Tag route type specific EVPN NLRI
   consists of the following:

                   +---------------------------------------+
                   |      RD   (8 octets)                  |
                   +---------------------------------------+
                   |  Ethernet Tag ID (4 octets)           |
                   +---------------------------------------+
                   |  IP Address Length (1 octet)          |
                   +---------------------------------------+
                   |   Originating Router's IP Addr        |
                   |          (4 or 16 octets)             |
                   +---------------------------------------+

   For procedures and usage of this route please see section 11
   "Handling of Multi-Destination Traffic", section 13 "Processing of
   Unknown Unicast Traffic" and section 16 "Multicast".

7.4 Ethernet Segment Route

   The Ethernet Segment Route is encoded in the EVPN NLRI using the
   Route Type value of 4. The Route Type Specific field of the NLRI is
   formatted as follows:

                   +---------------------------------------+
                   |      RD   (8 octets)                  |
                   +---------------------------------------+
                   |Ethernet Segment Identifier (10 octets)|
                   +---------------------------------------+
                   |  IP Address Length (1 octet)          |
                   +---------------------------------------+
                   |   Originating Router's IP Addr        |
                   |          (4 or 16 octets)             |
                   +---------------------------------------+

   For procedures and usage of this route please see section 8.5
   "Designated Forwarder Election". The IP address length is in bits.




Sajassi, et al.        Expires September 12, 2014              [Page 14]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


7.5 ESI Label Extended Community

   This extended community is a new transitive extended community with
   the Type field is 0x06, and the Sub-Type of 0x01. It may be
   advertised along with Ethernet Auto-Discovery routes and it enables
   split-horizon procedures for multi-homed sites as described in
   section 8.3 "Split Horizon".

   Each ESI Label Extended Community is encoded as a 8-octet value as
   follows:

        0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       | Type=0x06   | Sub-Type=0x01 | Flags (One Octet)  |Reserved=0  |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       | Reserved = 0|          ESI Label                              |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   The low order bit of the flags octet is defined as the "Single-
   Active" bit.  A value of 0 means that the multi-homed site is
   operating in All-Active redundancy mode and a value of 1 means that
   the multi-homed site is operating in Single-Active redundancy mode.

   The second low order bit of the flags octet is defined as the "Root-
   Leaf". A value of 0 means that this label is associated with a Root
   site; whereas, a value of 1 means that this label is associate with a
   Leaf site. The other bits must be set to 0.

7.6 ES-Import Route Target

   This is a new transitive Route Target extended community carried with
   the Ethernet Segment route. When used, it enables all the PEs
   connected to the same multi-homed site to import the Ethernet Segment
   routes. The value is derived automatically from the ESI by encoding
   the high order 6-byte portion of the 9-byte ESI Value in the ES-
   Import Route Target. The format of this extended community is as
   follows:

       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      | Type=0x06   | Sub-Type=0x02 |          ES-Import              |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                     ES-Import Cont'd                          |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   This document expands the definition of the Route Target extended
   community to allow the value of high order octet (Type field) to be
   0x06 (in addition to the values specified in rfc4360). The value of



Sajassi, et al.        Expires September 12, 2014              [Page 15]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


   low order octet (Sub-Type field) of 0x02 indicates that this extended
   community is of type "Route Target". The new value for Type field of
   0x06 indicates that the structure of this RT is a six bytes value
   (e.g., a MAC address). A BGP speaker that implements RT-Constrain
   (RFC4684) MUST apply the RT-Constrain procedures to the ES-import RT
   as-well.

   For procedures and usage of this attribute, please see section 8.1
   "MH Ethernet Segment Auto Discovery".

7.7 MAC Mobility Extended Community

   This extended community is a new transitive extended community with
   the Type field of 0x06 and the Sub-Type of 0x00. It may be advertised
   along with MAC Advertisement routes. The procedures for using this
   Extended Community are described in section 16 "MAC Mobility".

   The MAC Mobility Extended Community is encoded as a 8-octet value as
   follows:

   0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   | Type=0x06     | Sub-Type=0x00 |Flags(1 octet)|  Reserved=0    |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                       Sequence Number                         |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   The low order bit of the flags octet is defined as the
   "Sticky/static" flag and may be set to 1. A value of 1 means that the
   MAC address is static and cannot move.


7.8 Default Gateway Extended Community

   The Default Gateway community is an Extended Community of an Opaque
   Type (see 3.3 of rfc4360). It is a transitive community, which means
   that the first octet is 0x03. The value of the second octet (Sub-
   Type) is 0x030d (Default Gateway) as defined by IANA. The Value field
   of this community is reserved (set to 0 by the senders, ignored by
   the receivers).


8. Multi-homing Functions

   This section discusses the functions, procedures and associated BGP
   routes used to support multi-homing in EVPN. This covers both multi-
   homed device (MHD) as well as multi-homed network (MHN) scenarios.




Sajassi, et al.        Expires September 12, 2014              [Page 16]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


8.1 Multi-homed Ethernet Segment Auto-Discovery

   PEs connected to the same Ethernet segment can automatically discover
   each other with minimal to no configuration through the exchange of
   the Ethernet Segment route.

8.1.1 Constructing the Ethernet Segment Route

   The Route-Distinguisher (RD) MUST be a Type 1 RD [RFC4364]. The value
   field comprises an IP address of the MES (typically, the loopback
   address) followed by 0's.

   The Ethernet Segment Identifier MUST be set to the ten octet ESI
   identifier described in section 5.

   The BGP advertisement that advertises the Ethernet Segment route MUST
   also carry an ES-Import route target, as defined in section 7.6.

   The Ethernet Segment Route filtering MUST be done such that the
   Ethernet Segment Route is imported only by the PEs that are multi-
   homed to the same Ethernet Segment. To that end, each PE that is
   connected to a particular Ethernet segment constructs an import
   filtering rule to import a route that carries the ES-Import extended
   community, constructed from the ESI.

8.2 Fast Convergence

   In EVPN, MAC address reachability is learnt via the BGP control-plane
   over the MPLS network. As such, in the absence of any fast protection
   mechanism, the network convergence time is a function of the number
   of MAC Advertisement routes that must be withdrawn by the PE
   encountering a failure. For highly scaled environments, this scheme
   yields slow convergence.

   To alleviate this, EVPN defines a mechanism to efficiently and
   quickly signal, to remote PE nodes, the need to update their
   forwarding tables upon the occurrence of a failure in connectivity to
   an Ethernet segment. This is done by having each PE advertise a set
   of Ethernet A-D per Ethernet segment (per ES) routes for each locally
   attached Ethernet segment (refer to section 8.2.1 below for details
   on how this route is constructed). Upon a failure in connectivity to
   the attached segment, the PE withdraws the corresponding Ethernet A-D
   route. This triggers all PEs that receive the withdrawal to update
   their next-hop adjacencies for all MAC addresses associated with the
   Ethernet segment in question. If no other PE had advertised an
   Ethernet A-D route for the same segment, then the PE that received
   the withdrawal simply invalidates the MAC entries for that segment.
   Otherwise, the PE updates the next-hop adjacencies to point to the



Sajassi, et al.        Expires September 12, 2014              [Page 17]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


   backup PE(s).

8.2.1 Constructing the Ethernet A-D per Ethernet Segment (ES) Route

   This section describes the procedures used to construct the Ethernet
   A-D per ES route, which is used for fast convergence (as discussed
   above) and for advertising the ESI label used for split-horizon
   filtering (as discussed in section 8.3). Support of this route is
   MANDATORY.

   The Route-Distinguisher (RD) MUST be a Type 1 RD [RFC4364]. The value
   field comprises an IP address of the PE (typically, the loopback
   address) followed by a number unique to the PE.

   The Ethernet Segment Identifier MUST be a ten octet entity as
   described in section "Ethernet Segment". This document does not
   specify the use of the Ethernet A-D route when the Segment Identifier
   is set to 0.

   The Ethernet Tag ID MUST be set to MAX-ET.

   The MPLS label in the NLRI MUST be set to 0.

   The "ESI Label Extended Community" MUST be included in the route. If
   All-Active redundancy mode is desired, then the "Single-Active" bit
   in the flags of the ESI Label Extended Community MUST be set to 0 and
   the MPLS label in that extended community MUST be set to a valid MPLS
   label value. The MPLS label in this Extended Community is referred to
   as the ESI label and MUST have the same value in each Ethernet A-D
   per ES route advertised for the ES. This label MUST be a downstream
   assigned MPLS label if the advertising PE is using ingress
   replication for receiving multicast, broadcast or unknown unicast
   traffic from other PEs. If the advertising PE is using P2MP MPLS LSPs
   for sending multicast, broadcast or unknown unicast traffic, then
   this label MUST be an upstream assigned MPLS label. The usage of this
   label is described in section 8.3.

   If Single-Active redundancy mode is desired, then the "Single-Active"
   bit in the flags of the ESI Label Extended Community MUST be set to 1
   and the ESI label MUST be set to zero.

8.2.1.1. Ethernet A-D Route Targets

   Each Ethernet A-D per ES route MUST carry one or more Route Target
   (RT) attributes. The set of Ethernet A-D routes per ES MUST carry the
   entire set of RTs for all the EVPN instances to which the Ethernet
   Segment belongs.




Sajassi, et al.        Expires September 12, 2014              [Page 18]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


8.3 Split Horizon

   Consider a CE that is multi-homed to two or more PEs on an Ethernet
   segment ES1 operating in All-Active redundancy mode. If the CE sends
   a broadcast, unknown unicast, or multicast (BUM) packet to one of the
   non-DF (Designated Forwarder) PEs, say PE1, then PE1 will forward
   that packet to all or subset of the other PEs in that EVPN instance
   including the DF PE for that Ethernet segment. In this case the DF PE
   that the CE is multi-homed to MUST drop the packet and not forward
   back to the CE. This filtering is referred to as "split horizon"
   filtering in this document.

   When a set of PEs operating in Single-Active redundancy mode, the use
   of this split-horizon filtering mechanism is highly recommended
   because it prevents transient loop at the time of failure or recovery
   impacting the Ethernet Segment - e.g., when two PEs thinks that both
   are DFs for that segment before DF election procedure settles down.

   In order to achieve this split horizon function, every BUM packet
   originating from a non-DF PE is encapsulated with an MPLS label that
   identifies the Ethernet segment of origin (i.e. the segment from
   which the frame entered the EVPN network). This label is referred to
   as the ESI label, and MUST be distributed by all PEs when operating
   in All-Active redundancy mode using a set of Ethernet A-D per ES
   routes per section 8.2.1 above. The ESI label SHOULD be distributed
   by all PEs when operating in Single-Active redundancy mode using a
   set of Ethernet A-D per ES route. This route is imported by the PEs
   connected to the Ethernet Segment and also by the PEs that have at
   least one EVPN instance in common with the Ethernet Segment in the
   route. As described in section 8.1.1, the route MUST carry an ESI
   Label Extended Community with a valid ESI label. The disposition PE
   rely on the value of the ESI label to determine whether or not a BUM
   frame is allowed to egress a specific Ethernet segment.

8.3.1 ESI Label Assignment

   The following subsections describe the assignment procedures for the
   ESI label, which differ depending on the type of tunnels being used
   to deliver multi-destination packets in the EVPN network.

8.3.1.1 Ingress Replication

   Each PE attached to a given ES that is operating in All-Active or
   Single-Active redundancy mode and that uses ingress replication to
   receive BUM traffic advertises a downstream assigned ESI label in the
   set of Ethernet A-D per ES routes for that ES.  This label MUST be
   programmed in the platform label space by the advertising PE and the
   forwarding entry for this label must result in NOT forwarding packets



Sajassi, et al.        Expires September 12, 2014              [Page 19]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


   received with this label onto the Ethernet segment for which the
   label was distributed.

   The rules for the inclusion of the ESI label in a BUM packet by the
   ingress PE operating in All-Active redundancy mode are as follows:

   A non-DF ingress PE MUST include the ESI label distributed by the DF
   egress PE in the copy of a BUM packet sent to it.

   An ingress PE (DF or non-DF) SHOULD include the ESI label distributed
   by each non-DF egress PE in the copy of a BUM packet sent to it.

   The rules for the inclusion of the ESI label in a BUM packet by the
   ingress PE operating in Single-Active redundancy mode are as follows:

   An ingress DF PE SHOULD include the ESI label distributed by the
   egress PE in the copy of a BUM packet sent to it.

   In both All-Active and Single-Active redundancy mode, an ingress PE
   MUST NOT include an ESI label in the copy of a BUM packet sent to an
   egress PE that is not attached to the ES through which the BUM packet
   entered the EVI.

   As an example, consider PE1 and PE2 that are multi-homed to CE1 on
   ES1 and operating in All-Active multi-homing mode. Further consider
   that PE1 is using P2P or MP2P LSPs to send packets to PE2. Consider
   that PE1 is the non-DF for VLAN1 and PE2 is the DF for VLAN1, and PE1
   receives a BUM packet from CE1 on VLAN1 on ES1. In this scenario, PE2
   distributes an Inclusive Multicast Ethernet Tag route for VLAN1
   corresponding to an EVPN instance. So, when PE1 sends a BUM packet,
   that it receives from CE1, it MUST first push onto the MPLS label
   stack the ESI label that PE2 has distributed for ES1. It MUST then
   push on the MPLS label distributed by PE2 in the Inclusive Multicast
   Ethernet Tag route for VLAN1. The resulting packet is further
   encapsulated in the P2P or MP2P LSP label stack required to transmit
   the packet to PE2.  When PE2 receives this packet, it determines the
   set of ESIs to replicate the packet to from the top MPLS label, after
   any P2P or MP2P LSP labels have been removed. If the next label is
   the ESI label assigned by PE2 for ES1, then PE2 MUST NOT forward the
   packet onto ES1. If the next label is an ESI label which has not been
   assigned by PE2, then PE2 MUST drop the packet. It should be noted
   that in this scenario, if PE2 receives a BUM traffic for VLAN1 from
   CE1, then it should encapsulate the packet with an ESI label received
   from PE1 when sending it to the PE1 in order to avoid any transient
   loop during a failure scenario impacting ES1 (e.g., port or link
   failure).

8.3.1.2. P2MP MPLS LSPs



Sajassi, et al.        Expires September 12, 2014              [Page 20]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


   The non-DF PEs attached to a given ES that is operating in All-Active
   redundancy mode and that use P2MP LSPs to send BUM traffic advertise
   an upstream assigned ESI label in the set of Ethernet A-D per ES
   routes for that ES. This label is upstream assigned by the PE that
   advertises the route. This label MUST be programmed by the other PEs,
   that are connected to the ESI advertised in the route, in the context
   label space for the advertising PE. Further the forwarding entry for
   this label must result in NOT forwarding packets received with this
   label onto the Ethernet segment that the label was distributed for.
   This label MUST also be programmed by the other PEs, that import the
   route but are not connected to the ESI advertised in the route, in
   the context label space for the advertising PE. Further the
   forwarding entry for this label must be a POP with no other
   associated action.

   The DF PE attached to a given ES that is operating in Single-Active
   redundancy mode and that use P2MP LSPs to send BUM traffic should
   advertise an upstream assigned ESI label in the set of Ethernet A-D
   per ES routes for that ES just as above paragraph.

   As an example, consider PE1 and PE2 that are multi-homed to CE1 on
   ES1 and operating in All-Active multi-homing mode. Also consider PE3
   belongs to one of the EVPN instances of ES1.  Further, assume that
   PE1 which is the non-DF, using P2MP MPLS LSPs to send BUM packets.
   When PE1 sends a BUM packet, that it receives from CE1, it MUST first
   push onto the MPLS label stack the ESI label that it has assigned for
   the ESI that the packet was received on. The resulting packet is
   further encapsulated in the P2MP MPLS label stack necessary to
   transmit the packet to the other PEs. Penultimate hop popping MUST be
   disabled on the P2MP LSPs used in the MPLS transport infrastructure
   for EVPN. When PE2 receives this packet, it de-capsulates the top
   MPLS label and forwards the packet using the context label space
   determined by the top label. If the next label is the ESI label
   assigned by PE1 to ES1, then PE2 MUST NOT forward the packet onto
   ES1. When PE3 receives this packet, it de-capsulates the top MPLS
   label and forwards the packet using the context label space
   determined by the top label. If the next label is the ESI label
   assigned by PE1 to ES1 and PE3 is not connected to ES1, then PE3 MUST
   pop the label and flood the packet over all local ESIs in that EVPN
   instance. It should be noted that when PE2 sends a BUM frame over a
   P2MP LSP, it should encapsulate the frame with an ESI label even
   though it is the DF for that VLAN in order to avoid any transient
   loop during a failure scenario impacting ES1 (e.g., port or link
   failure).


8.4 Aliasing and Backup-Path




Sajassi, et al.        Expires September 12, 2014              [Page 21]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


   In the case where a CE is multi-homed to multiple PE nodes, using a
   LAG with All-Active redundancy, it is possible that only a single PE
   learns a set of the MAC addresses associated with traffic transmitted
   by the CE. This leads to a situation where remote PE nodes receive
   MAC advertisement routes, for these addresses, from a single PE even
   though multiple PEs are connected to the multi-homed segment. As a
   result, the remote PEs are not able to effectively load-balance
   traffic among the PE nodes connected to the multi-homed Ethernet
   segment. This could be the case, for e.g. when the PEs perform data-
   path learning on the access, and the load-balancing function on the
   CE hashes traffic from a given source MAC address to a single PE.
   Another scenario where this occurs is when the PEs rely on control
   plane learning on the access (e.g. using ARP), since ARP traffic will
   be hashed to a single link in the LAG.

   To address this issue, EVPN introduces the concept of 'Aliasing'
   which is the ability of a PE to signal that it has reachability to an
   EVPN instance on a given ES even when it has learnt no MAC addresses
   from that EVI/ES. The Ethernet A-D per EVI route is used for this
   purpose. A remote PE that receives a MAC advertisement route with
   non-reserved ESI SHOULD consider the advertised MAC address to be
   reachable via all PEs that have advertised reachability to that MAC
   address' EVI/ES via the combination of an Ethernet A-D per EVI route
   for that EVI/ES (and Ethernet Tag if applicable) AND Ethernet A-D per
   ES routes for that ES with the 'Single-Active' bit in the flags of
   the ESI Label Extended Community set to 0.

   Note that the Ethernet A-D per EVI route may be received by a remote
   PE before it receives the set of Ethernet A-D per ES routes.
   Therefore, in order to handle corner cases and race conditions, the
   Ethernet A-D per EVI route MUST NOT be used for traffic forwarding by
   a remote PE until it also receives the associated set of Ethernet A-D
   per ES routes.

   Backup-path is a closely related function, but it is used in Single-
   Active redundancy mode.  In this case a PE also advertises that it
   has reachability to a give EVI/ES using same combination of Ethernet
   A-D per EVI route and Ethernet A-D per ES route as above, but with
   the 'Single-Active' bit in the flags of the ESI Label Extended
   Community set to 1.   A remote PE that receives a MAC advertisement
   route with non-reserved ESI SHOULD consider the advertised MAC
   address to be reachable via any PE that has advertised this
   combination of Ethernet A-D routes and it SHOULD install a backup-
   path for that MAC address.

8.4.1 Constructing the Ethernet A-D per EVPN Instance (EVI) Route

   This section describes the procedures used to construct the Ethernet



Sajassi, et al.        Expires September 12, 2014              [Page 22]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


   A-D per EVPN Instance (EVI) route, which is used for aliasing (as
   discussed above). Support of this route is OPTIONAL.

   Route-Distinguisher (RD) MUST be set to the RD of the EVI that is
   advertising the NLRI. An RD MUST be assigned for a given EVI on an
   PE. This RD MUST be unique across all EVIs on an PE. It is
   RECOMMENDED to use the Type 1 RD [RFC4364]. The value field comprises
   an IP address of the PE (typically, the loopback address) followed by
   a number unique to the PE.  This number may be generated by the PE.
   Or in the Unique VLAN EVPN case, the low order 12 bits may be the 12
   bit VLAN ID, with the remaining high order 4 bits set to 0.

   The Ethernet Segment Identifier MUST be a ten octet entity as
   described in section "Ethernet Segment Identifier". This document
   does not specify the use of the Ethernet A-D route when the Segment
   Identifier is set to 0.

   The Ethernet Tag ID is the identifier of an Ethernet Tag on the
   Ethernet segment. This value may be a 12 bit VLAN ID, in which case
   the low order 12 bits are set to the VLAN ID and the high order 20
   bits are set to 0. Or it may be another Ethernet Tag used by the
   EVPN.  It MAY be set to the default Ethernet Tag on the Ethernet
   segment or to the value 0.

   Note that the above allows the Ethernet A-D route to be advertised
   with one of the following granularities:

      + One Ethernet A-D route for a given <ESI, Ethernet Tag ID> tuple
        per EVI. This is applicable when the PE uses MPLS-based
        disposition.

      + One Ethernet A-D route per <ESI, EVI> (where the Ethernet
        Tag ID is set to 0). This is applicable when the PE uses
        MAC-based disposition, or when the PE uses MPLS-based
        disposition when no VLAN translation is required.

   The usage of the MPLS label is described in the section on "Load
   Balancing of Unicast Packets".

   The Next Hop field of the MP_REACH_NLRI attribute of the route MUST
   be set to the IPv4 or IPv6 address of the advertising PE.

8.4.1.1 Ethernet A-D Route Targets

   The Ethernet A-D route MUST carry one or more Route Target (RT)
   attributes. RTs may be configured (as in IP VPNs), or may be derived
   automatically.




Sajassi, et al.        Expires September 12, 2014              [Page 23]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


   If an PE uses Route Target Constrain [RT-CONSTRAIN], the PE SHOULD
   advertise all such RTs using Route Target Constrains. The use of RT
   Constrains allows each Ethernet A-D route to reach only those PEs
   that are configured to import at least one RT from the set of RTs
   carried in the Ethernet A-D route.

8.4.1.1.1 Auto-Derivation from the Ethernet Tag ID

   For the "Unique VLAN EVPN" scenario, it is highly desirable to auto-
   derive the RT from the Ethernet Tag ID (VLAN ID) for that EVPN
   instance. The following is the procedure for performing such auto-
   derivation.

        +    The Global Administrator field of the RT MUST be set to
             the Autonomous System (AS) number that the PE associated
         with.

        +    The two octet VLAN ID MUST be encoded in the lower two
             octets of the Local Administrator field.


8.5 Designated Forwarder Election

   Consider a CE that is a host or a router that is multi-homed directly
   to more than one PE in an EVPN instance on a given Ethernet segment.
   One or more Ethernet Tags may be configured on the Ethernet segment.
   In this scenario only one of the PEs, referred to as the Designated
   Forwarder (DF), is responsible for certain actions:

        -   Sending multicast and broadcast traffic, on a given Ethernet
            Tag on a particular Ethernet segment, to the CE.

        -   Flooding unknown unicast traffic (i.e. traffic for
            which an PE does not know the destination MAC address),
            on a given Ethernet Tag on a particular Ethernet segment
            to the CE, if the environment requires flooding of
            unknown unicast traffic.

   Note that this behavior, which allows selecting a DF at the
   granularity of <ESI, EVI> for multicast, broadcast and unknown
   unicast traffic, is the default behavior in this specification.

   Note that a CE always sends packets belonging to a specific flow
   using a single link towards an PE. For instance, if the CE is a host
   then, as mentioned earlier, the host treats the multiple links that
   it uses to reach the PEs as a Link Aggregation Group (LAG). The CE
   employs a local hashing function to map traffic flows onto links in
   the LAG.



Sajassi, et al.        Expires September 12, 2014              [Page 24]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


   If a bridged network is multi-homed to more than one PE in an EVPN
   network via switches, then the support of All-Active redundancy mode
   requires the bridge network to be connected to two or more PEs using
   a LAG.

   If a bridged network does not connect to the PEs using LAG, then only
   one of the links between the switched bridged network and the PEs
   must be the active link for a given EVPN instance. In this case, the
   set of Ethernet A-D per ES routes advertised by each PE MUST have the
   'Single-Active' bit in the flags of the ESI Label Extended Community
   set to 1.

   The default procedure for DF election at the granularity of <ESI,
   EVI> is referred to as "service carving". With service carving, it is
   possible to elect multiple DFs per Ethernet Segment (one per EVI) in
   order to perform load-balancing of multi-destination traffic destined
   to a given Segment. The load-balancing procedures carve up the EVI
   space among the PE nodes evenly, in such a way that every PE is the
   DF for a disjoint set of EVIs. The procedure for service carving is
   as follows:

   1. When a PE discovers the ESI of the attached Ethernet Segment, it
   advertises an Ethernet Segment route with the associated ES-Import
   extended community attribute.

   2. The PE then starts a timer (default value = 3 seconds) to allow
   the reception of Ethernet Segment routes from other PE nodes
   connected to the same Ethernet Segment. This timer value MUST be same
   across all PEs connected to the same Ethernet Segment.

   3. When the timer expires, each PE builds an ordered list of the IP
   addresses of all the PE nodes connected to the Ethernet Segment
   (including itself), in increasing numeric value. Each IP address in
   this list is extracted from the "Originator Router's IP address"
   field of the advertised Ethernet Segment route. Every PE is then
   given an ordinal indicating its position in the ordered list,
   starting with 0 as the ordinal for the PE with the numerically lowest
   IP address. The ordinals are used to determine which PE node will be
   the DF for a given EVPN instance on the Ethernet Segment using the
   following rule: Assuming a redundancy group of N PE nodes, the PE
   with ordinal i is the DF for an EVPN instance with an associated
   Ethernet Tag value V when (V mod N) = i. In the case where multiple
   Ethernet Tags are associated with a single EVPN instance, then the
   numerically lowest Ethernet Tag value in that EVPN instance MUST be
   used in the modulo function.

   It should be noted that using "Originator Router's IP address" field
   in the Ethernet Segment route to get the PE IP address needed for the



Sajassi, et al.        Expires September 12, 2014              [Page 25]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


   ordered list, allows for a CE to be multi-homed across different ASes
   if such need every arises.

   4. The PE that is elected as a DF for a given EVPN instance will
   unblock traffic for the Ethernet Tags associated with that EVPN
   instance. Note that the DF PE unblocks multi-destination traffic in
   the egress direction towards the Segment. All non-DF PEs continue to
   drop multi-destination traffic (for the associated EVPN instances) in
   the egress direction towards the Segment.

   In the case of link or port failure, the affected PE withdraws its
   Ethernet Segment route. This will re-trigger the service carving
   procedures on all the PEs in the RG. For PE node failure, or upon PE
   commissioning or decommissioning, the PEs re-trigger the service
   carving. In case of a Single-Active multi-homing, when a service
   moves from one PE in the RG to another PE as a result of re-carving,
   the PE, which ends up being the elected DF for the service, must
   trigger a MAC address flush notification towards the associated
   Ethernet Segment. This can be done, for e.g. using IEEE 802.1ak MVRP
   'new' declaration.


8.6. Interoperability with Single-homing PEs

   Let's refer to PEs that only support single-homed CE devices as
   single-homing PEs. For single-homing PEs, all the above multi-homing
   procedures can be omitted; however, to allow for single-homing PEs to
   fully inter-operate with multi-homing PEs, some of the multi-homing
   procedures described above SHOULD be supported even by single-homing
   PEs:

   - procedures related to processing Ethernet A-D route for the purpose
   of Fast Convergence (9.2 Fast Convergence), to let single-homing PEs
   benefit from fast convergence

   - procedures related to processing Ethernet A-D route for the purpose
   of Aliasing (9.4 Aliasing and Backup-path), to let single-homing PEs
   benefit from load balancing

   - procedures related to processing Ethernet A-D route for the purpose
   of Backup-path (9.4 Aliasing and Backup-path), to let single-homing
   PEs to benefit from the corresponding convergence improvement


9. Determining Reachability to Unicast MAC Addresses

   PEs forward packets that they receive based on the destination MAC
   address. This implies that PEs must be able to learn how to reach a



Sajassi, et al.        Expires September 12, 2014              [Page 26]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


   given destination unicast MAC address.

   There are two components to MAC address learning, "local learning"
   and "remote learning":

9.1. Local Learning

   A particular PE must be able to learn the MAC addresses from the CEs
   that are connected to it. This is referred to as local learning.

   The PEs in a particular EVPN instance MUST support local data plane
   learning using standard IEEE Ethernet learning procedures. An PE must
   be capable of learning MAC addresses in the data plane when it
   receives packets such as the following from the CE network:

        - DHCP requests

        - ARP request for its own MAC.

        - ARP request for a peer.

   Alternatively PEs MAY learn the MAC addresses of the CEs in the
   control plane or via management plane integration between the PEs and
   the CEs.

   There are applications where a MAC address that is reachable via a
   given PE on a locally attached Segment (e.g. with ESI X) may move
   such that it becomes reachable via another PE on another Segment
   (e.g. with ESI Y).  This is referred to as a "MAC Mobility".
   Procedures to support this are described in section "MAC Mobility".

9.2. Remote learning

   A particular PE must be able to determine how to send traffic to MAC
   addresses that belong to or are behind CEs connected to other PEs
   i.e. to remote CEs or hosts behind remote CEs. We call such MAC
   addresses as "remote" MAC addresses.

   This document requires an PE to learn remote MAC addresses in the
   control plane. In order to achieve this, each PE advertises the MAC
   addresses it learns from its locally attached CEs in the control
   plane, to all the other PEs in that EVPN instance, using MP-BGP and
   specifically the MAC Advertisement route.

9.2.1. Constructing the BGP EVPN MAC/IP Address Advertisement

   BGP is extended to advertise these MAC addresses using the MAC/IP
   Advertisement route type in the EVPN NLRI.



Sajassi, et al.        Expires September 12, 2014              [Page 27]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


   The RD MUST be the RD of the EVI that is advertising the NLRI. The
   procedures for setting the RD for a given EVI are described in
   section 8.4.1.

   The Ethernet Segment Identifier is set to the ten octet ESI described
   in section "Ethernet Segment".

   The Ethernet Tag ID may be zero or may represent a valid Ethernet Tag
   ID.  This field may be non-zero when there are multiple bridge
   domains in the MAC-VRF (e.g., the PE needs to perform qualified
   learning for the VLANs in that MAC-VRF).

   When the the Ethernet Tag ID in the NLRI is set to a non-zero value,
   for a particular bridge domain, then this Ethernet Tag may either be
   the Ethernet tag value associated with the CE, e.g., VLAN ID, or it
   may be the Ethernet Tag Identifier, e.g., VLAN ID assigned by the
   EVPN provider and mapped to the CE's Ethernet tag. The latter would
   be the case if the CE Ethernet tags, e.g., VLAN ID, for a particular
   bridge domain are different on different CEs.

   The MAC address length field is in bits and it is set to 48. The
   encoding of a MAC address MUST be the 6-octet MAC address specified
   by [802.1D-ORIG] [802.1D-REV].

   The IP Address Field is optional. By default, the IP Address Length
   field is set to 0 and the IP address field is omitted from the route.
   When a valid IP address needs to be advertised, it is then encoded in
   this route. When an IP address is present, the IP Address Length
   field is in bits and it is set to 32 or 128 bits. Other IP Address
   Length values are outside the scope of this document. The encoding of
   an IP address MUST be either 4 octets for IPv4 or 16 octets for IPv6.
   The length field of EVPN NLRI (which is in octets and is described in
   section 7) is sufficient to determine whether an IP address is
   encoded in this route and if so, whether the encoded IP address is
   IPV4 or IPv6.

   The MPLS label1 field is encoded as 3 octets, where the high-order 20
   bits contain the label value. The MPLS label1 MUST be downstream
   assigned and it is associated with the MAC address being advertised
   by the advertising PE. The advertising PE uses this label when it
   receives an MPLS-encapsulated packet to perform forwarding based on
   the destination MAC address. The forwarding procedures are specified
   in section "Forwarding Unicast Packets" and "Load Balancing of
   Unicast Packets".

   An PE may advertise the same single EVPN label for all MAC addresses
   in a given EVI. This label assignment methodology is referred to as a
   per EVI label assignment. Alternatively, an PE may advertise a unique



Sajassi, et al.        Expires September 12, 2014              [Page 28]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


   EVPN label per <ESI, Ethernet Tag> combination. This label assignment
   methodology is referred to as a per <ESI, Ethernet Tag> label
   assignment. As a third option, an PE may advertise a unique EVPN
   label per MAC address. All of these methodologies have their
   tradeoffs. The choice of a particular label assignment methodology is
   purely local to the PE that originates the route.

   Per EVI label assignment requires the least number of EVPN labels,
   but requires a MAC lookup in addition to an MPLS lookup on an egress
   PE for forwarding. On the other hand, a unique label per <ESI,
   Ethernet Tag> or a unique label per MAC allows an egress PE to
   forward a packet that it receives from another PE, to the connected
   CE, after looking up only the MPLS labels without having to perform a
   MAC lookup. This includes the capability to perform appropriate VLAN
   ID translation on egress to the CE.

   The MPLS label2 field is an optional field and if it is present, then
   it is encoded as 3 octets, where the high-order 20 bits contain the
   label value. The use of MPLS label2 is for further study.

   The Next Hop field of the MP_REACH_NLRI attribute of the route MUST
   be set to the IPv4 or IPv6 address of the advertising PE.

   The BGP advertisement for the MAC advertisement route MUST also carry
   one or more Route Target (RT) attributes.  RTs may be configured (as
   in IP VPNs), or may be derived automatically from the Ethernet Tag
   ID, in the Unique VLAN case, as described in section "Ethernet A-D
   Route per EVPN".

   It is to be noted that this document does not require PEs to create
   forwarding state for remote MACs when they are learnt in the control
   plane. When this forwarding state is actually created is a local
   implementation matter.

9.2.2 Route Resolution

   If the Ethernet Segment Identifier field in a received MAC
   Advertisement route is set to the reserved ESI value of 0 or MAX-ESI,
   then the receiving PE MUST install forwarding state for the
   associated MAC Address based on the MAC Advertisement route alone.

   If the Ethernet Segment Identifier field in a received MAC
   Advertisement route is set to a non-reserved ESI, and the receiving
   PE is locally attached to the same ESI, then the PE does not alter
   its forwarding state based on the received route. This ensures that
   local routes are preferred to remote routes.

   If the Ethernet Segment Identifier field in a received MAC



Sajassi, et al.        Expires September 12, 2014              [Page 29]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


   Advertisement route is set to a non-reserved ESI, then the receiving
   PE MUST install forwarding state for a given MAC address only when
   both the MAC Advertisement route AND the associated set of Ethernet
   A-D per ES routes have been received.

   To illustrate this with an example, consider two PEs (PE1 and PE2)
   connected to a multi-homed Ethernet Segment ES1. All-Active
   redundancy mode is assumed. A given MAC address M1 is learnt by PE1
   but not PE2. On PE3, the following states may arise:

   T1- When the MAC Advertisement Route from PE1 and the set of Ethernet
   A-D per ES routes from PE1 and PE2 are received, PE3 can forward
   traffic destined to M1 to both PE1 and PE2.

   T2- If after T1, PE1 withdraws its set of Ethernet A-D per ES routes,
   then PE3 forwards traffic destined to M1 to PE2 only.

   T3- If after T1, PE2 withdraws its set of Ethernet A-D per ES routes,
   then PE3 forwards traffic destined to M1 to PE1 only.

   T4- If after T1, PE1 withdraws its MAC Advertisement route, then PE3
   treats traffic to M1 as unknown unicast. Note, here, that had PE2
   also advertised a MAC route for M1 before PE1 withdraws its MAC
   route, then PE3 would have continued forwarding traffic destined to
   M1 to PE2.

10. ARP and ND

   The IP address field in the MAC advertisement route may optionally
   carry one of the IP addresses associated with the MAC address. This
   provides an option which can be used to minimize the flooding of ARP
   or Neighbor Discovery (ND) messages over the MPLS network and to
   remote CEs. This option also minimizes ARP (or ND) message processing
   on end-stations/hosts connected to the EVPN network. An PE may learn
   the IP address associated with a MAC address in the control or
   management plane between the CE and the PE. Or, it may learn this
   binding by snooping certain messages to or from a CE. When an PE
   learns the IP address associated with a MAC address, of a locally
   connected CE, it may advertise this address to other PEs by including
   it in the MAC Advertisement route. The IP Address may be an IPv4
   address encoded using four octets, or an IPv6 address encoded using
   sixteen octets. For ARP and ND purposes, the IP Address length field
   MUST be set to 32 for an IPv4 address or to 128 for an IPv6 address.

   If there are multiple IP addresses associated with a MAC address,
   then multiple MAC advertisement routes MUST be generated, one for
   each IP address. For instance, this may be the case when there are
   both an IPv4 and an IPv6 address associated with the MAC address.



Sajassi, et al.        Expires September 12, 2014              [Page 30]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


   When the IP address is dissociated with the MAC address, then the MAC
   advertisement route with that particular IP address MUST be
   withdrawn.

   When an PE receives an ARP request for an IP address from a CE, and
   if the PE has the MAC address binding for that IP address, the PE
   SHOULD perform ARP proxy by responding to the ARP request.

10.1 Default Gateway

   When a PE needs to perform inter-subnet forwarding where each subnet
   is represented by a different broadcast domain (e.g., different VLAN)
   the inter-subnet forwarding is performed at layer 3 and the PE that
   performs such function is called the default gateway. In this case
   when the PE receives an ARP Request for the IP address of the default
   gateway, the PE originates an ARP Reply.

   Each PE that acts as a default gateway for a given EVPN instance MAY
   advertise in the EVPN control plane its default gateway MAC address
   using the MAC advertisement route, and indicates that such route is
   associated with the default gateway.  This is accomplished by
   requiring the route to carry the Default Gateway extended community
   defined in [Section 7.8 Default Gateway Extended Community]. The ESI
   field is set to zero when advertising the MAC route with the Default
   Gateway extended community.

   Unless it is known a priori (by means outside of this document) that
   all PEs of a given EVPN instance act as a default gateway for that
   EVPN instance, the MPLS label MUST be set to a valid downstream
   assigned label.

   Furthermore, even if all PEs of a given EVPN instance do act as a
   default gateway for that EVPN instance, but only some, but not all,
   of these PEs have sufficient (routing) information to provide inter-
   subnet routing for all the inter-subnet traffic originated within the
   subnet associated with the EVPN instance, then when such PE
   advertises in the EVPN control plane its default gateway MAC address
   using the MAC advertisement route, and indicates that such route is
   associated with the default gateway, the route MUST carry a valid
   downstream assigned label.

   If all PEs of a given EVPN instance act as a default gateway for that
   EVPN instance, and the same default gateway MAC address is used
   across all gateway devices, then no such advertisement is needed.
   However, if each default gateway uses a different MAC address, then
   each default gateway needs to be aware of other gateways' MAC
   addresses and thus the need for such advertisement. This is called
   MAC address aliasing since a single default GW can be represented by



Sajassi, et al.        Expires September 12, 2014              [Page 31]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


   multiple MAC addresses.

   Each PE that receives this route and imports it as per procedures
   specified in this document follows the procedures in this section
   when replying to ARP Requests that it receives if such Requests are
   for the IP address in the received EVPN route.

   Each PE that acts as a default gateway for a given EVPN instance that
   receives this route and imports it as per procedures specified in
   this document MUST create MAC forwarding state that enables it to
   apply IP forwarding to the packets destined to the MAC address
   carried in the route.


11. Handling of Multi-Destination Traffic

   Procedures are required for a given PE to send broadcast or multicast
   traffic, received from a CE encapsulated in a given Ethernet Tag
   (VLAN) in an EVPN instance, to all the other PEs that span that
   Ethernet Tag (VLAN) in that EVPN instance. In certain scenarios,
   described in section "Processing of Unknown Unicast Packets", a given
   PE may also need to flood unknown unicast traffic to other PEs.

   The PEs in a particular EVPN instance may use ingress replication,
   P2MP LSPs or MP2MP LSPs to send unknown unicast, broadcast or
   multicast traffic to other PEs.

   Each PE MUST advertise an "Inclusive Multicast Ethernet Tag Route" to
   enable the above. The following subsection provides the procedures to
   construct the Inclusive Multicast Ethernet Tag route. Subsequent
   subsections describe in further detail its usage.

11.1. Construction of the Inclusive Multicast Ethernet Tag Route

   The RD MUST be the RD of the EVI that is advertising the NLRI. The
   procedures for setting the RD for a given EVPN instance on a PE are
   described in section 8.4.1.

   The Ethernet Tag ID is the identifier of the Ethernet Tag. It MAY be
   set to 0 or to a valid Ethernet Tag value.

   The Originating Router's IP address MUST be set to an IP address of
   the PE.  This address SHOULD be common for all the EVIs on the PE
   (e.,g., this address may be PE's loopback address). The IP Address
   Length field is in bits.

   The Next Hop field of the MP_REACH_NLRI attribute of the route MUST
   be set to the same IP address as the one carried in the Originating



Sajassi, et al.        Expires September 12, 2014              [Page 32]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


   Router's IP Address field.

   The BGP advertisement for the Inclusive Multicast Ethernet Tag route
   MUST also carry one or more Route Target (RT) attributes. The
   assignment of RTs described in the section on "Constructing the BGP
   EVPN MAC Address Advertisement" MUST be followed.

11.2. P-Tunnel Identification

   In order to identify the P-Tunnel used for sending broadcast, unknown
   unicast or multicast traffic, the Inclusive Multicast Ethernet Tag
   route MUST carry a "PMSI Tunnel Attribute" as specified in [BGP
   MVPN].

   Depending on the technology used for the P-tunnel for the EVPN
   instance on the PE, the PMSI Tunnel attribute of the Inclusive
   Multicast Ethernet Tag route is constructed as follows.

        + If the PE that originates the advertisement uses a
          P-Multicast tree for the P-tunnel for EVPN, the PMSI
          Tunnel attribute MUST contain the identity of the tree
          (note that the PE could create the identity of the
          tree prior to the actual instantiation of the tree).

        + An PE that uses a P-Multicast tree for the P-tunnel MAY
          aggregate two or more EVPN instances (EVIs) present
          on the PE onto the same tree. In this case, in addition
          to carrying the identity of the tree, the PMSI Tunnel
          attribute MUST carry an MPLS upstream assigned label which
          the PE has bound uniquely to the EVI associated with this
          update (as determined by its RTs).

          If the PE has already advertised Inclusive Multicast
          Ethernet Tag routes for two or more EVIs that it now
          desires to aggregate, then the PE MUST re-advertise
          those routes. The re-advertised routes MUST be the same
          as the original ones, except for the PMSI Tunnel attribute
          and the label carried in that attribute.

        + If the PE that originates the advertisement uses ingress
          replication for the P-tunnel for EVPN, the route MUST
          include the PMSI Tunnel attribute with the Tunnel Type set to
          Ingress Replication and Tunnel Identifier set to a routable
          address of the PE. The PMSI Tunnel attribute MUST carry a
          downstream assigned MPLS label. This label is used to
          demultiplex the broadcast, multicast or unknown unicast EVPN
          traffic received over a MP2P tunnel by the PE.




Sajassi, et al.        Expires September 12, 2014              [Page 33]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


        + The Leaf Information Required flag of the PMSI Tunnel
          attribute MUST be set to zero, and MUST be ignored on receipt.

12. Processing of Unknown Unicast Packets

   The procedures in this document do not require the PEs to flood
   unknown unicast traffic to other PEs. If PEs learn CE MAC addresses
   via a control plane protocol, the PEs can then distribute MAC
   addresses via BGP, and all unicast MAC addresses will be learnt prior
   to traffic to those destinations.

   However, if a destination MAC address of a received packet is not
   known by the PE, the PE may have to flood the packet. When flooding,
   one must take into account "split horizon forwarding" as follows: The
   principles behind the following procedures are borrowed from the
   split horizon forwarding rules in VPLS solutions [RFC4761] and
   [RFC4762].  When an PE capable of flooding (say PEx) receives an
   unknown destination MAC address, it floods the frame.  If the frame
   arrived from an attached CE, PEx must send a copy of the frame to
   every other attached CE participating in that EVPN instance, on a
   different ESI than the one it received the frame on, as long as the
   PE is the DF for the egress ESI. In addition, the PE must flood the
   frame to all other PEs participating in that EVPN instance. If, on
   the other hand, the frame arrived from another PE (say PEy), PEx must
   send a copy of the packet only to attached CEs as long as it is the
   DF for the egress ESI. PEx MUST NOT send the frame to other PEs,
   since PEy would have already done so. Split horizon forwarding rules
   apply to unknown MAC addresses.

   Whether or not to flood packets to unknown destination MAC addresses
   should be an administrative choice, depending on how learning happens
   between CEs and PEs.

   The PEs in a particular EVPN instance may use ingress replication
   using RSVP-TE P2P LSPs or LDP MP2P LSPs for sending unknown unicast
   traffic to other PEs. Or they may use RSVP-TE P2MP or LDP P2MP for
   sending such traffic to other PEs.

12.1. Ingress Replication

   If ingress replication is in use, the P-Tunnel attribute, carried in
   the Inclusive Multicast Ethernet Tag routes for the EVPN instance,
   specifies the downstream label that the other PEs can use to send
   unknown unicast, multicast or broadcast traffic for that EVPN
   instance to this particular PE.

   The PE that receives a packet with this particular MPLS label MUST
   treat the packet as a broadcast, multicast or unknown unicast packet.



Sajassi, et al.        Expires September 12, 2014              [Page 34]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


   Further if the MAC address is a unicast MAC address, the PE MUST
   treat the packet as an unknown unicast packet.

12.2. P2MP MPLS LSPs

   The procedures for using P2MP LSPs are very similar to VPLS
   procedures [VPLS-MCAST]. The P-Tunnel attribute used by an PE for
   sending unknown unicast, broadcast or multicast traffic for a
   particular EVPN instance is advertised in the Inclusive Ethernet Tag
   Multicast route as described in section "Handling of Multi-
   Destination Traffic".

   The P-Tunnel attribute specifies the P2MP LSP identifier. This is the
   equivalent of an Inclusive tree in [VPLS-MCAST]. Note that multiple
   Ethernet Tags, which may be in different EVPN instances, may use the
   same P2MP LSP, using upstream labels [VPLS-MCAST]. This is the
   equivalent of an Aggregate Inclusive tree in [VPLS-MCAST]. When P2MP
   LSPs are used for flooding unknown unicast traffic, packet re-
   ordering is possible.

   The PE that receives a packet on the P2MP LSP specified in the PMSI
   Tunnel Attribute MUST treat the packet as a broadcast, multicast or
   unknown unicast packet. Further if the MAC address is a unicast MAC
   address, the PE MUST treat the packet as an unknown unicast packet.

13. Forwarding Unicast Packets

   This section describes procedures for forwarding unicast packets by
   PEs, where such packets are received from either directly connected
   CEs, or from some other PEs.

13.1. Forwarding packets received from a CE

   When an PE receives a packet from a CE, on a given Ethernet Tag, it
   must first look up the source MAC address of the packet. In certain
   environments the source MAC address MAY be used to authenticate the
   CE and determine that traffic from the host can be allowed into the
   network. Source MAC lookup MAY also be used for local MAC address
   learning.

   If the PE decides to forward the packet, the destination MAC address
   of the packet must be looked up. If the PE has received MAC address
   advertisements for this destination MAC address from one or more
   other PEs or learned it from locally connected CEs, it is considered
   as a known MAC address. Otherwise, the MAC address is considered as
   an unknown MAC address.

   For known MAC addresses the PE forwards this packet to one of the



Sajassi, et al.        Expires September 12, 2014              [Page 35]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


   remote PEs or to a locally attached CE. When forwarding to a remote
   PE, the packet is encapsulated in the EVPN MPLS label advertised by
   the remote PE, for that MAC address, and in the MPLS LSP label stack
   to reach the remote PE.

   If the MAC address is unknown and if the administrative policy on the
   PE requires flooding of unknown unicast traffic then:

   - The PE MUST flood the packet to other PEs. The PE MUST first
   encapsulate the packet in the ESI MPLS label as described in section
   8.3. If ingress replication is used, the packet MUST be replicated
   one or more times to each remote PE with the outermost label being an
   MPLS label determined as follows: This is the MPLS label advertised
   by the remote PE in a PMSI Tunnel Attribute in the Inclusive
   Multicast Ethernet Tag route for an <EVPN instance, Ethernet Tag>
   combination. The Ethernet Tag in the route must be the same as the
   Ethernet Tag associated with the interface on which the ingress PE
   receives the packet. If P2MP LSPs are being used the packet MUST be
   sent on the P2MP LSP that the PE is the root of for the Ethernet Tag
   in the EVPN instance. If the same P2MP LSP is used for all Ethernet
   Tags, then all the PEs in the EVPN instance MUST be the leaves of the
   P2MP LSP. If a distinct P2MP LSP is used for a given Ethernet Tag in
   the EVPN instance, then only the PEs in the Ethernet Tag MUST be the
   leaves of the P2MP LSP. The packet MUST be encapsulated in the P2MP
   LSP label stack.

   If the MAC address is unknown then, if the administrative policy on
   the PE does not allow flooding of unknown unicast traffic:

   - The PE MUST drop the packet.

13.2. Forwarding packets received from a remote PE

   This section described the procedures for forwarding known and
   unknown unicast packets received from a remote PE.

13.2.1. Unknown Unicast Forwarding

   When an PE receives an MPLS packet from a remote PE then, after
   processing the MPLS label stack, if the top MPLS label ends up being
   a P2MP LSP label associated with an EVPN instance or in case of
   ingress replication the downstream label advertised in the P-Tunnel
   attribute, and after performing the split horizon procedures
   described in section "Split Horizon":

   - If the PE is the designated forwarder of BUM traffic on a
   particular set of ESIs for the Ethernet Tag, the default behavior is
   for the PE to flood the packet on these ESIs. In other words, the



Sajassi, et al.        Expires September 12, 2014              [Page 36]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


   default behavior is for the PE to assume that for BUM traffic, it is
   not required to perform a destination MAC address lookup. As an
   option, the PE may perform a destination MAC lookup to flood the
   packet to only a subset of the CE interfaces in the Ethernet Tag. For
   instance the PE may decide to not flood an BUM packet on certain
   Ethernet segments even if it is the DF on the Ethernet segment, based
   on administrative policy.

   - If the PE is not the designated forwarder on any of the ESIs for
   the Ethernet Tag, the default behavior is for it to drop the packet.

13.2.2. Known Unicast Forwarding

   If the top MPLS label ends up being an EVPN label that was advertised
   in the unicast MAC advertisements, then the PE either forwards the
   packet based on CE next-hop forwarding information associated with
   the label or does a destination MAC address lookup to forward the
   packet to a CE.

14. Load Balancing of Unicast Frames

   This section specifies the load balancing procedures for sending
   known unicast frames to a multi-homed CE.

14.1. Load balancing of traffic from an PE to remote CEs

   Whenever a remote PE imports a MAC advertisement for a given <ESI,
   Ethernet Tag> in an EVI, it MUST examine all imported Ethernet A-D
   routes for that ESI in order to determine the load-balancing
   characteristics of the Ethernet segment.

14.1.1 Single-Active Redundancy Mode

   For a given ES, if the remote PE has imported the set of Ethernet A-D
   per ES routes from at least one PE, where the "Single-Active" flag in
   the ESI Label Extended Community is set, then the remote PE MUST
   deduce that the ES is operating in Single-Active redundancy mode. As
   such, the MAC address will be reachable only via the PE announcing
   the associated MAC Advertisement route - this is referred to as the
   primary PE. The other PEs advertising the set of Ethernet A-D per ES
   routes for the same ES provide backup paths for that ES, in case the
   primary PE encounters a failure, and are referred to as backup PEs.
   It should be noted that the primary PE for a given <ES, EVI> is the
   DF for that <ES, EVI>.

   If the primary PE encounters a failure, it MAY withdraw its set of
   Ethernet A-D per ES routes for the affected ES prior to withdrawing
   it set of MAC Advertisement routes.



Sajassi, et al.        Expires September 12, 2014              [Page 37]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


   If there is only one backup PE for a given ES, the remote PE MAY use
   the primary PE's withdrawal of its set of Ethernet A-D per ES routes
   as a trigger to update its forwarding entries, for the associated MAC
   addresses, to point towards the backup PE. As the backup PE starts
   learning the MAC addresses over its attached ES, it will start
   sending MAC Advertisement routes while the failed PE withdraws its
   routes. This mechanism minimizes the flooding of traffic during fail-
   over events.

   If there is more than one backup PE for a given ES, the remote PE
   MUST use the primary PE's withdrawal of its set of Ethernet A-D per
   ES routes as a trigger to start flooding traffic for the associated
   MAC addresses (as long as flooding of unknown unicast is
   administratively allowed), as it is not possible to select a single
   backup PE.

14.1.2 All-Active Redundancy Mode

   For a given ES, if the remote PE has imported the set of Ethernet A-D
   per ES routes from one or more PEs and none of them have the "Single-
   Active" flag in the ESI Label Extended Community set, then the remote
   PE MUST deduce that the ES is operating in All-Active redundancy
   mode.  A remote PE that receives a MAC advertisement route with non-
   reserved ESI SHOULD consider the advertised MAC address to be
   reachable via all PEs that have advertised reachability to that MAC
   address' EVI/ES via the combination of an Ethernet A-D per EVI route
   for that EVI/ES (and Ethernet Tag if applicable) AND an Ethernet A-D
   per ES route for that ES.  The remote PE MUST use received MAC
   Advertisement routes and Ethernet A-D per EVI/per ES routes to
   construct the set of next-hops for the advertised MAC address.


   The remote PE MUST use the MAC advertisement and eligible Ethernet A-
   D routes to construct the set of next-hops that it can use to send
   the packet to the destination MAC. Each next-hop comprises an MPLS
   label stack that is to be used by the egress PE to forward the
   packet. This label stack is determined as follows:

   -If the next-hop is constructed as a result of a MAC route then this
   label stack MUST be used. However, if the MAC route doesn't exist,
   then the next-hop and MPLS label stack is constructed as a result of
   the Ethernet A-D routes. Note that the following description applies
   to determining the label stack for a particular next-hop to reach a
   given PE, from which the remote PE has received and imported Ethernet
   A-D routes that have the matching ESI and Ethernet Tag as the one
   present in the MAC advertisement. The Ethernet A-D routes mentioned
   in the following description refer to the ones imported from this
   given PE.



Sajassi, et al.        Expires September 12, 2014              [Page 38]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


   -If a set of Ethernet A-D per ES routes for that ES AND an Ethernet
   A-D route per EVI exist, then the label from that latter route must
   be used.

   The following example explains the above.

   Consider a CE (CE1) that is dual-homed to two PEs (PE1 and PE2) on a
   LAG interface (ES1), and is sending packets with MAC address MAC1 on
   VLAN1 (mapped to EVI1). A remote PE, say PE3, is able to learn that
   MAC1 is reachable via PE1 and PE2. Both PE1 and PE2 may advertise
   MAC1 in BGP if they receive packets with MAC1 from CE1. If this is
   not the case, and if MAC1 is advertised only by PE1, PE3 still
   considers MAC1 as reachable via both PE1 and PE2 as both PE1 and PE2
   advertise a set of Ethernet A-D per ES routes for ES1 as well as an
   Ethernet A-D per EVI route for <EVI1, ES1>.

   The MPLS label stack to send the packets to PE1 is the MPLS LSP stack
   to get to PE1 and the EVPN label advertised by PE1 for CE1's MAC.

   The MPLS label stack to send packets to PE2 is the MPLS LSP stack to
   get to PE2 and the MPLS label in the Ethernet A-D route advertised by
   PE2 for <ES1, VLAN1>, if PE2 has not advertised MAC1 in BGP.

   We will refer to these label stacks as MPLS next-hops.

   The remote PE (PE3) can now load balance the traffic it receives from
   its CEs, destined for CE1, between PE1 and PE2.  PE3 may use N-Tuple
   flow information to hash traffic into one of the MPLS next-hops for
   load balancing of IP traffic. Alternatively PE3 may rely on the
   source MAC addresses for load balancing.

   Note that once PE3 decides to send a particular packet to PE1 or PE2
   it can pick one out of multiple possible paths to reach the
   particular remote PE using regular MPLS procedures. For instance, if
   the tunneling technology is based on RSVP-TE LSPs, and PE3 decides to
   send a particular packet to PE1, then PE3 can choose from multiple
   RSVP-TE LSPs that have PE1 as their destination.

   When PE1 or PE2 receive the packet destined for CE1 from PE3, if the
   packet is a unicast MAC packet it is forwarded to CE1.  If it is a
   multicast or broadcast MAC packet then only one of PE1 or PE2 must
   forward the packet to the CE. Which of PE1 or PE2 forward this packet
   to the CE is determined based on which of the two is the DF.

   If the connectivity between the multi-homed CE and one of the PEs
   that it is attached to, fails, the PE MUST withdraw the set of
   Ethernet A-D per ES routes that had been previously advertised for
   that ES. When the MAC entry on the PE ages out, the PE MUST withdraw



Sajassi, et al.        Expires September 12, 2014              [Page 39]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


   the MAC address from BGP. Note that to aid convergence, the Ethernet
   Tag A-D routes MAY be withdrawn before the MAC routes. This enables
   the remote PEs to remove the MPLS next-hop to this particular PE from
   the set of MPLS next-hops that can be used to forward traffic to the
   CE. For further details and procedures on withdrawal of EVPN route
   types in the event of PE to CE failures please section "PE to CE
   Network  Failures".

14.2. Load balancing of traffic between an PE and a local CE

   A CE may be configured with more than one interface connected to
   different PEs or the same PE for load balancing, using a technology
   such as LAG. The PE(s) and the CE can load balance traffic onto these
   interfaces using one of the following mechanisms.

14.2.1. Data plane learning

   Consider that the PEs perform data plane learning for local MAC
   addresses learned from local CEs. This enables the PE(s) to learn a
   particular MAC address and associate it with one or more interfaces,
   if the technology between the PE and the CE supports multi-pathing.
   The PEs can now load balance traffic destined to that MAC address on
   the multiple interfaces.

   Whether the CE can load balance traffic that it generates on the
   multiple interfaces is dependent on the CE implementation.

14.2.2. Control plane learning

   The CE can be a host that advertises the same MAC address using a
   control protocol on both interfaces. This enables the PE(s) to learn
   the host's MAC address and associate it with one or more interfaces.
   The PEs can now load balance traffic destined to the host on the
   multiple interfaces. The host can also load balance the traffic it
   generates onto these interfaces and the PE that receives the traffic
   employs EVPN forwarding procedures to forward the traffic.

15. MAC Mobility

   It is possible for a given host or end-station (as defined by its MAC
   address) to move from one Ethernet segment to another;  this is
   referred to as 'MAC Mobility' or 'MAC move' and it is different from
   the multi-homing situation in which a given MAC address is reachable
   via multiple PEs for the same Ethernet segment.  In a MAC move, there
   would be two sets of MAC Advertisement routes, one set with the new
   Ethernet segment and one set with the previous Ethernet segment, and
   the MAC address would appear to be reachable via each of these
   segments.



Sajassi, et al.        Expires September 12, 2014              [Page 40]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


   In order to allow all of the PEs in the EVPN instance to correctly
   determine the current location of the MAC address, all advertisements
   of it being reachable via the previous Ethernet segment MUST be
   withdrawn by the PEs, for the previous Ethernet segment, that had
   advertised it.

   If local learning is performed using the data plane, these PEs will
   not be able to detect that the MAC address has moved to another
   Ethernet segment and the receipt of MAC Advertisement routes, with
   the MAC Mobility extended community attribute, from other PEs serves
   as the trigger for these PEs to withdraw their advertisements.  If
   local learning is performed using the control or management planes,
   these interactions serve as the trigger for these PEs to withdraw
   their advertisements.

   In a situation where there are multiple moves of a given MAC,
   possibly between the same two Ethernet segments, there may be
   multiple withdrawals and re-advertisements.  In order to ensure that
   all PEs in the EVPN instance receive all of these correctly through
   the intervening BGP infrastructure, it is necessary to introduce a
   sequence number into the MAC Mobility extended community attribute.

   An implementation MUST handle the scenarios where the sequence number
   wraps around to process mobility event correctly.

   Every MAC mobility event for a given MAC address will contain a
   sequence number that is set using the following rules:

   - A PE advertising a MAC address for the first time advertises it
   with no MAC Mobility extended community attribute.

   - A PE detecting a locally attached MAC address for which it had
   previously received a MAC Advertisement route with a different
   Ethernet segment identifier advertises the MAC address in a MAC
   Advertisement route tagged with a MAC Mobility extended community
   attribute with a sequence number one greater than the sequence number
   in the MAC mobility attribute of the received MAC Advertisement
   route. In the case of the first mobility event for a given MAC
   address, where the received MAC Advertisement route does not carry a
   MAC Mobility attribute, the value of the sequence number in the
   received route is assumed to be 0 for purpose of this processing.

   - A PE detecting a locally attached MAC address for which it had
   previously received a MAC Advertisement route with the same non-zero
   Ethernet segment identifier advertises it with:
      i.  no MAC Mobility extended community attribute, if the received
      route did not carry said attribute.




Sajassi, et al.        Expires September 12, 2014              [Page 41]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


      ii. a MAC Mobility extended community attribute with the sequence
      number equal to the highest of the sequence number(s) in the
      received MAC Advertisement route(s), if the received route(s) is
      (are) tagged with a MAC Mobility extended community attribute.

   - A PE detecting a locally attached MAC address for which it had
   previously received a MAC Advertisement route with the same zero
   Ethernet segment identifier (single-homed scenarios) advertises it
   with MAC mobility extended community attribute with the sequence
   number set properly. In case of single-homed scenarios, there is no
   need for ESI comparison. The reason ESI comparison is done for multi-
   homing, is to prevent false detection of MAC move among the PEs
   attached to the same multi-homed site.

   A PE receiving a MAC Advertisement route for a MAC address with a
   different Ethernet segment identifier and a higher sequence number
   than that which it had previously advertised, withdraws its MAC
   Advertisement route. If two (or more) PEs advertise the same MAC
   address with same sequence number but different Ethernet segment
   identifiers, a PE that receives these routes selects the route
   advertised by the PE with lowest IP address as the best route. If the
   PE is the originator of the MAC route and it receives the same MAC
   address with the same sequence number that it generated, it will
   compare its own IP address with the IP address of the remote PE and
   will select the lowest IP. If its own route is not the best one, it
   will withdraw the route.


15.1. MAC Duplication Issue

   A situation may arise where the same MAC address is learned by
   different PEs in the same VLAN because of two (or more hosts) being
   mis-configured with the same (duplicate) MAC address. In such
   situation, the traffic originating from these hosts would trigger
   continuous MAC moves among the PEs attached to these hosts. It is
   important to recognize such situation and avoid incrementing the
   sequence number (in the MAC Mobility attribute) to infinity. In order
   to remedy such situation, a PE that detects a MAC mobility event by
   way of local learning starts an M-second timer (default value of M =
   180) and if it detects N MAC moves before the timer expires (default
   value for N = 5), it concludes that a duplicate MAC situation has
   occurred. The PE MUST alert the operator and stop sending and
   processing any BGP MAC Advertisement routes for that MAC address till
   a corrective action is taken by the operator. The values of M and N
   MUST be configurable to allow for flexibility in operator control.
   Note that the other PEs in the E-VPN instance will forward the
   traffic for the duplicate MAC address to one of the PEs advertising
   the duplicate MAC address.



Sajassi, et al.        Expires September 12, 2014              [Page 42]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


15.2. Sticky MAC addresses

   There are scenarios in which it is desired to configure some MAC
   addresses as static so that they are not subjected to MAC move. In
   such scenarios, these MAC addresses are advertised with MAC Mobility
   Extended Community where static flag is set to 1 and sequence number
   is set to zero. If a PE receives such advertisements and later learns
   the same MAC address(es) via local learning, then the PE MUST alert
   the operator.


16. Multicast & Broadcast

   The PEs in a particular EVPN instance may use ingress replication or
   P2MP LSPs to send multicast traffic to other PEs.

16.1. Ingress Replication

   The PEs may use ingress replication for flooding BUM traffic as
   described in section "Handling of Multi-Destination Traffic". A given
   broadcast packet must be sent to all the remote PEs. However a given
   multicast packet for a multicast flow may be sent to only a subset of
   the PEs. Specifically a given multicast flow may be sent to only
   those PEs that have receivers that are interested in the multicast
   flow. Determining which of the PEs have receivers for a given
   multicast flow is done using explicit tracking described below.


16.2. P2MP LSPs

   An PE may use an "Inclusive" tree for sending an BUM packet. This
   terminology is borrowed from [VPLS-MCAST].

   A variety of transport technologies may be used in the SP network.
   For inclusive P-Multicast trees, these transport technologies include
   point-to-multipoint LSPs created by RSVP-TE or mLDP.

16.2.1. Inclusive Trees

   An Inclusive Tree allows the use of a single multicast distribution
   tree, referred to as an Inclusive P-Multicast tree, in the SP network
   to carry all the multicast traffic from a specified set of EVPN
   instances on a given PE. A particular P-Multicast tree can be set up
   to carry the traffic originated by sites belonging to a single EVPN
   instance, or to carry the traffic originated by sites belonging to
   several EVPN instances. The ability to carry the traffic of more than
   one EVPN instance on the same tree is termed 'Aggregation' and the
   tree is called an Aggregate Inclusive P-Multicast tree or Aggregate



Sajassi, et al.        Expires September 12, 2014              [Page 43]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


   Inclusive tree for short. The Aggregate Inclusive tree needs to
   include every PE that is a member of any of the EVPN instances that
   are using the tree. This implies that an PE may receive multicast
   traffic for a multicast stream even if it doesn't have any receivers
   that are interested in receiving traffic for that stream.

   An Inclusive or Aggregate Inclusive tree as defined in this document
   is a P2MP tree.  A P2MP tree is used to carry traffic only for EVPN
   CEs that are connected to the PE that is the root of the tree.

   The procedures for signaling an Inclusive tree are the same as those
   in [VPLS-MCAST] with the VPLS-AD route replaced with the Inclusive
   Multicast Ethernet Tag route. The P-Tunnel attribute [VPLS-MCAST] for
   an Inclusive tree is advertised with the Inclusive Multicast Ethernet
   Tag route as described in section "Handling of Multi-Destination
   Traffic". Note that for an Aggregate Inclusive tree, an PE can
   "aggregate" multiple EVPN instances on the same P2MP LSP using
   upstream labels. The procedures for aggregation are the same as those
   described in [VPLS-MCAST], with VPLS A-D routes replaced by EVPN
   Inclusive Multicast ET routes.


17. Convergence

   This section describes failure recovery from different types of
   network failures.

17.1. Transit Link and Node Failures between PEs

   The use of existing MPLS Fast-Reroute mechanisms can provide failure
   recovery in the order of 50ms, in the event of transit link and node
   failures in the infrastructure that connects the PEs.

17.2. PE Failures

   Consider a host host1 that is dual homed to PE1 and PE2. If PE1
   fails, a remote PE, PE3, can discover this based on the failure of
   the BGP session.  This failure detection can be in the sub-second
   range if BFD is used to detect BGP session failure. PE3 can update
   its forwarding state to start sending all traffic for host1 to only
   PE2. It is to be noted that this failure recovery is potentially
   faster than what would be possible if data plane learning were to be
   used. As in that case PE3 would have to rely on re-learning of MAC
   addresses via PE2.

17.3. PE to CE Network Failures

   When an Ethernet segment connected to an PE fails or when a Ethernet



Sajassi, et al.        Expires September 12, 2014              [Page 44]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


   Tag is decommissioned on an Ethernet segment, then the PE MUST
   withdraw the Ethernet A-D route(s) announced for the <ESI, Ethernet
   Tags> that are impacted by the failure or decommissioning. In
   addition, the PE MUST also withdraw the MAC advertisement routes that
   are impacted by the failure or decommissioning.

   The Ethernet A-D routes should be used by an implementation to
   optimize the withdrawal of MAC advertisement routes. When an PE
   receives a withdrawal of a particular Ethernet A-D route from an PE
   it SHOULD consider all the MAC advertisement routes, that are learned
   from the same <ESI, Ethernet Tag> as in the Ethernet A-D route, from
   the advertising PE, as having been withdrawn. This optimizes the
   network convergence times in the event of PE to CE failures.


18. Frame Ordering

   In a MAC address, bit-1 of the most significant byte is used for
   unicast/multicast indication and bit-2 is used for globally unique
   versus locally administered MAC address. If the value of the 2nd
   nibble (bits 4 thorough 8) of the most significant byte of the
   destination MAC address (which follows the last MPLS label) happens
   to be 0x4 or 0x6, then the Ethernet frame can be misinterpreted as an
   IPv4 or IPv6 packet by intermediate P nodes performing ECMP based on
   deep packet inspection, thus resulting in load balancing packets
   belonging to the same flow on different ECMP paths and subjecting
   them to different delays. Therefore, packets belonging to the same
   flow can arrive at the destination out of order. This out of order
   delivery can happen during steady state in absence of any failures
   resulting in significant impact to the network operation.

   In order to avoid any such mis-ordering, the following rules are
   applied:

   - If a network uses deep packet inspection for its ECMP, then the
   control word SHOULD be used when sending EVPN encapsulated packets
   over a MP2P LSP.

   - If a network uses Entropy label [RFC6790], then the control word
   SHOULD NOT be used when sending EVPN encapsulated packet over a MP2P
   LSP.

   - When sending EVPN encapsulated packets over a P2MP LSP or TE P2P
   LSP, then the control world SHOULD NOT be used.


   The control word is defined as follows:




Sajassi, et al.        Expires September 12, 2014              [Page 45]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |0 0 0 0|   Reserved            |       Sequence Number         |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+


   In the above diagram the first 4 bits MUST be set to 0.  The rest of
   the first 16 bits are reserved for future use. They MUST be set to 0
   when transmitting, and MUST be ignored upon receipt. The next 16 bits
   provide a sequence number that MUST also be set to zero by default.


19. Acknowledgements

   Special thanks to Yakov Rekhter for reviewing this draft several
   times and providing valuable comments and for his very engaging
   discussions on several topics of this draft that helped shape this
   document. We would also like to thank Pedro Marques, Kaushik Ghosh,
   Nischal Sheth, Robert Raszuk, Amit Shukla, and Nadeem Mohammed for
   discussions that helped shape this document. We would also like to
   thank Han Nguyen for his comments and support of this work. We would
   also like to thank Steve Kensil and Reshad Rahman for their reviews.
   We would like to thank Jorge Rabadan for his contribution to section
   5 of this draft. We like to thank Thomas Morin for his review of this
   draft and his contribution of section 8.6. Last but not least, many
   thanks to Jakob Heitz for his help to improve several sections of
   this draft.

   We would also like to thank Clarence Filsfils, Dennis Cai, Quaizar
   Vohra, Kireeti Kompella, Apurva Mehta for their contributions to this
   document.


20. Security Considerations

   Security considerations discussed in [RFC4761] and [RFC4762] apply to
   this document for MAC learning in data-plane over an Attachment
   Circuit (AC) and for flooding of unknown unicast and ARP messages
   over the MPLS/IP core. Security considerations discussed in [RFC4364]
   apply to this document for MAC learning in control-plane over the
   MPLS/IP core. This section describes additional considerations.

   As mentioned in [RFC4761], there are two aspects to achieving data
   privacy and protecting against denial-of-service attacks in a VPN:
   securing the control plane and protecting the forwarding path.
   Compromise of the control plane could result in a PE sending customer
   data belonging to some EVPN to another EVPN, or black-holing EVPN



Sajassi, et al.        Expires September 12, 2014              [Page 46]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


   customer data, or even sending it to an eavesdropper; none of which
   are acceptable from a data privacy point of view.  In addition,
   compromise of the control plane could result in black-holing EVPN
   customer data and could provide opportunities for unauthorized EVPN
   data usage (e.g., exploiting traffic replication within a multicast
   tree to amplify a denial-of-service attack based on sending large
   amounts of traffic).

   The mechanisms in this document use BGP for the control plane. Hence,
   techniques such as in [RFC5925] help authenticate BGP messages,
   making it harder to spoof updates (which can be used to divert EVPN
   traffic to the wrong EVPN instance) or withdrawals (denial-of-service
   attacks).  In the multi-AS methods (b) and (c), this also means
   protecting the inter-AS BGP sessions, between the ASBRs, the PEs, or
   the Route Reflectors.

   Note that [RFC5925] will not help in keeping MPLS labels private --
   knowing the labels, one can eavesdrop on EVPN traffic. However, this
   requires access to the data path within an SP network, which is
   assumed to be composed of trusted nodes/links.

   One of the requirements for protecting the data plane is that the
   MPLS labels be accepted only from valid interfaces. For a PE, valid
   interfaces comprise links from other routers in the PE's own AS.  For
   an ASBR, valid interfaces comprise links from other routers in the
   ASBR's own AS, and links from other ASBRs in ASes that have instances
   of a given EVPN.  It is especially important in the case of multi-AS
   EVPN instances that one accept EVPN packets only from valid
   interfaces.

   It is also important to help limit malicious traffic into a network
   for an imposter MAC address. The mechanism described in section 15.1,
   shows how duplicate MAC addresses can be detected and continous false
   MAC mobility can be prevented. The mechanism described in section
   15.2, shows how MAC addresses can be pinned to a given Ethernet
   Segment, such that if they appear behind any other Ethernet Segments,
   the traffic for those MAC addresses be prevented from entering the
   EVPN network from the other Ethernet Segments.

21. Co-authors

   In addition to the authors listed on the front page, the following
   individuals have also helped to shape this document:

      Keyur Patel
      Samer Salam
      Sami Boutros
      Cisco



Sajassi, et al.        Expires September 12, 2014              [Page 47]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


      Yakov Rekhter
      Ravi Shekhar
      Juniper Networks

      Florin Balus
      Nuage Networks

22.  IANA Considerations

   This document defines a new NLRI, called "EVPN", to be carried in BGP
   using multiprotocol extensions.  This NLRI uses the existing AFI of
   25 (L2VPN). IANA has assigned it a SAFI value of 70.

23. References

23.1 Normative References

   [RFC4364] "BGP/MPLS IP VPNs", Rosen, Rekhter, et. al., February 2006

   [RFC4761] Kompella, K. and Y. Rekhter, "Virtual Private LAN Service
              (VPLS) Using BGP for Auto-Discovery and Signaling", RFC
              4761, January 2007.

   [RFC4762] Lasserre, M. and V. Kompella, "Virtual Private LAN Service
              (VPLS) Using Label Distribution Protocol (LDP) Signaling",
              RFC 4762, January 2007.

   [RFC4271] Y. Rekhter et. al., "A Border Gateway Protocol 4 (BGP-4)",
              RFC 4271, January 2006

   [RFC4760] T. Bates et. al., "Multiprotocol Extensions for BGP-4", RFC
              4760, January 2007


23.2 Informative References

   [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119, March 1997.

   [EVPN-REQ] A. Sajassi, R. Aggarwal et. al., "Requirements for
              Ethernet VPN", draft-ietf-l2vpn-evpn-req-04.txt, July
              2013.

   [VPLS-MCAST] "Multicast in VPLS". R. Aggarwal et.al., draft-ietf-
              l2vpn-vpls-mcast-14.txt, July 2013.

   [RT-CONSTRAIN] P. Marques et. al., "Constrained Route Distribution
              for Border Gateway Protocol/MultiProtocol Label Switching



Sajassi, et al.        Expires September 12, 2014              [Page 48]


INTERNET DRAFT        BGP MPLS Based Ethernet VPN         March 12, 2014


              (BGP/MPLS) Internet Protocol (IP) Virtual Private Networks
              (VPNs)", RFC 4684, November 2006.

   [RFC6790] K. Kompella et. al, "The Use of Entropy Labels in MPLS
              Forwarding", RFC 6790, November 2012.

24. Author's Address

      Ali Sajassi
      Cisco
      Email: sajassi@cisco.com


      Rahul Aggarwal
      Email: raggarwa_1@yahoo.com


      Nabil Bitar
      Verizon Communications
      Email : nabil.n.bitar@verizon.com


      Aldrin Isaac
      Bloomberg
      Email: aisaac71@bloomberg.net


      James Uttaro
      AT&T
      Email: uttaro@att.com


      John Drake
      Juniper Networks
      Email: jdrake@juniper.net


      Wim Henderickx
      Alcatel-Lucent
      e-mail: wim.henderickx@alcatel-lucent.com











Sajassi, et al.        Expires September 12, 2014              [Page 49]