Network Working Group R. R. Stewart
INTERNET-DRAFT M. A. Ramalho
Cisco Systems
Q. Xie
Motorola
M. Tuexen
Siemens AG
I. Rytina
M. Belinchon
Ericsson
P. Conrad
Temple University
expires in six months May 12, 2002
Stream Control Transmission Protocol (SCTP)
Dynamic Address Reconfiguration
<draft-ietf-tsvwg-addip-sctp-05.txt>
Status of This Memo
This document is an Internet-Draft and is in full conformance with
all provisions of Section 10 of RFC 2026 [RFC2026]. Internet-Drafts
are working documents of the Internet Engineering Task Force (IETF),
its areas, and its working groups. Note that other groups may also
distribute working documents as Internet-Drafts.
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
Abstract
This document describes extensions to the Stream Control
Transmission Protocol (SCTP) [RFC2960] that provides a method to
reconfigure IP address information on an existing association.
TABLE OF CONTENTS
1. Introduction............................................... 2
2. Conventions................................................ 3
3. Additional Chunks and Parameters........................... 3
3.1 New Chunk Types........................................... 3
3.1.1 Address Configuration Change Chunk (ASCONF)............. 3
3.1.2 Address Configuration Acknowledgment Chunk
(ASCONF-ACK)............................................ 4
3.2 New Parameter Types....................................... 5
3.2.1 Add IP Address.......................................... 6
Stewart et.al. [Page 1]
Internet Draft SCTP Dynamic Address Reconfiguration May 2002
3.2.2 Delete IP Address........................................ 6
3.2.3 Error Cause Indication................................... 7
3.2.4 Set Primary IP Address................................... 8
3.2.5 Success Indication....................................... 9
3.2.6 Adaption Layer Indication................................10
3.3 New Error Causes...........................................10
3.3.1 Error Cause: Request to Delete Last Remaining IP Address.10
3.3.2 Error Cause: Operation Refused Due to Resource Shortage..11
3.3.3 Error Cause: Request to Delete Source IP Address.........12
3.3.4 Error Cause: Association Aborted due to illegal
ASCONF-ACK...............................................12
4. Procedures..................................................12
4.1 ASCONF Chunk Procedures....................................13
4.1.1 Congestion Control of ASCONF Chunks......................14
4.2 Upon reception of an ASCONF Chunk..........................15
4.3 General rules for address manipulation.....................17
4.3.1 A special case for OOTB ABORT chunks.....................19
4.3.2 A special case for changing an address...................20
4.4 Setting of the primary address.............................20
5. Abstract description of SCTP addressing.....................21
6. Security Considerations.....................................24
7. IANA considerations.........................................24
8. Acknowledgments.............................................24
9. Authors' Addresses..........................................24
10.Normative References........................................25
1. Introduction
To extend the utility and application scenarios of SCTP, this
document introduces optional extensions that provide SCTP with the
ability to:
1. reconfigure IP address information on an existing association.
2. set the remote primary path.
3. exchange adaptation layer information during association setup.
These extensions enable SCTP to be utilized in the following
applications:
1. For computational or networking platforms that allow
addition/removal of physical interface cards this feature can
provide a graceful method to add to the interfaces of an existing
association. For IPv6 this feature allows renumbering of existing
associations.
2. This provides a method for an endpoint to request that its peer
set its primary destination address. This can be useful when an
address is about to be deleted, or when an endpoint has some
predetermined knowledge about which is the preferred address to
receive SCTP packets upon.
3. This feature can be used to extend the usability of SCTP without
modifying it by allowing endpoints to exchange some information
during association setup.
Stewart et.al. [Page 2]
Internet Draft SCTP Dynamic Address Reconfiguration May 2002
2. Conventions
The keywords MUST, MUST NOT, REQUIRED, SHALL, SHALL NOT, SHOULD,
SHOULD NOT, RECOMMENDED, NOT RECOMMENDED, MAY, and OPTIONAL, when
they appear in this document, are to be interpreted as described in
RFC 2119 [RFC2119].
3. Additional Chunks and Parameters
This section describes the addition of two new chunks and, eight
new parameters to allow:
- Dynamic addition of IP Addresses to an association.
- Dynamic deletion of IP Addresses to an association.
- A request to set the primary address the peer will
use when sending to an endpoint.
Additionally, this section describes three new error causes that
support these new chunks and parameters.
3.1 New Chunk Types
This section defines two new chunk types that will be used to
transfer the control information reliably. Table 1 illustrates the
two new chunk types.
Chunk Type Chunk Name
--------------------------------------------------------------
0xC1 Address Configuration Change Chunk (ASCONF)
0x80 Address Configuration Acknowledgment (ASCONF-ACK)
Table 1: Address Configuration Chunks
It should be noted that the ASCONF Chunk format requires the
receiver to report to the sender if it does not understand the
ASCONF Chunk. This is accomplished by setting the upper bits in the
chunk type as described in [RFC2960] section 3.2. Note that the
upper two bits in the ASCONF Chunk are set to one. As defined in
[RFC2960] section 3.2, setting these upper bits in this manner will
cause the receiver that does not understand this chunk to skip the
chunk and continue processing, but report in an Operation Error
Chunk using the 'Unrecognized Chunk Type' cause of error.
3.1.1 Address Configuration Change Chunk (ASCONF)
This chunk is used to communicate to the remote endpoint one of the
configuration change requests that MUST be acknowledged. The
information carried in the ASCONF Chunk uses the form of a
Type-Length-Value (TLV), as described in "3.2.1
Optional/Variable-length Parameter Format" in [RFC2960], for
all variable parameters.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
Stewart et.al. [Page 3]
Internet Draft SCTP Dynamic Address Reconfiguration May 2002
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = 0xC1 | Chunk Flags | Chunk Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Serial Number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Address Parameter |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ASCONF Parameter #1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
\ \
/ .... /
\ \
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ASCONF Parameter #N |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Serial Number : 32 bits (unsigned integer)
This value represents a Serial Number for the ASCONF Chunk. The
valid range of Serial Number is from 0 to 4294967295 (2**32 - 1).
Serial Numbers wrap back to 0 after reaching 4294967295.
Reserved: 24 bits
Reserved, set to 0 by the sender and ignored by the
receiver.
Address Parameter : 8 or 20 bytes (depending on type)
This field contains an address parameter, either IPv6
or IPv4, from RFC2960. The address is an address of the
sender of the ASCONF chunk, the address MUST be considered
part of the association by the peer endpoint (the receiver
of the ASCONF chunk). This field may be used by the receiver
of the ASCONF to help in finding the association. This
parameter MUST be present in every ASCONF message i.e.
it is a mandatory TLV parameter.
Note the host name address parameter is NOT allowed.
ASCONF Parameter: TLV format
Each Address configuration change is represented by a TLV
parameter as defined in Section 3.2. One or more requests
may be present in an ASCONF Chunk.
3.1.2 Address Configuration Acknowledgment Chunk (ASCONF-ACK)
This chunk is used by the receiver of an ASCONF Chunk to acknowledge
the reception. It carries zero or more results for any ASCONF
Parameters that were processed by the receiver.
Stewart et.al. [Page 4]
Internet Draft SCTP Dynamic Address Reconfiguration May 2002
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = 0x80 | Chunk Flags | Chunk Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Serial Number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ASCONF Parameter Response#1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
\ \
/ .... /
\ \
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ASCONF Parameter Response#N |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Serial Number : 32 bits (unsigned integer)
This value represents the Serial Number for the received ASCONF Chunk
that is acknowledged by this chunk. This value is
copied from the received ASCONF Chunk.
ASCONF Parameter Response : TLV format
The ASCONF Parameter Response is used in the ASCONF-ACK to report
status of ASCONF processing. By default, if a responding endpoint
does not include any Error Cause, a success is indicated. Thus a
sender of an ASCONF-ACK MAY indicate complete success of all TLVs in
an ASCONF by returning only the Chunk Type, Chunk Flags, Chunk Length
(set to 8) and the Serial Number.
3.2 New Parameter Types
The six new parameters added follow the format defined in section
3.2.1 of [RFC2960]. Table 2 and 3 describes the parameters.
Address Configuration Parameters Parameter Type
-------------------------------------------------
Add IP Address 0xC001
Delete IP Address 0xC002
Set Primary Address 0xC004
Adaption Layer Indication 0xC006
Table 2: Parameters used in ASCONF Parameter
Address Configuration Parameters Parameter Type
-------------------------------------------------
Error Cause Indication 0xC003
Success report 0xC005
Table 3: Parameters used in ASCONF Parameter Response
Stewart et.al. [Page 5]
Internet Draft SCTP Dynamic Address Reconfiguration May 2002
3.2.1 Add IP Address
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = 0xC001 | Length = Variable |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ASCONF-Request Correlation ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Address Parameter |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
ASCONF-Request Correlation ID: 32 bits
This is an opaque integer assigned by the sender to identify each
request parameter. It is in host byte order and is only meaningful
to the sender. The receiver of the ASCONF Chunk will copy this 32
bit value into the ASCONF Response Correlation ID field of the
ASCONF-ACK response parameter. The sender of the ASCONF can use this
same value in the ASCONF-ACK to find which request the response is
for.
Address Parameter: TLV
This field contains an IPv4 or IPv6 address parameter as described
in 3.3.2.1 of RFC2960. The complete TLV is wrapped within this
parameter. It informs the receiver that the address specified is to
be added to the existing association.
An example TLV requesting that the IPv4 address 10.1.1.1 be
added to the association would look as follows:
+--------------------------------+
| Type=0xC001 | Length = 16 |
+--------------------------------+
| C-ID = 0x01023474 |
+--------------------------------+
| Type=5 | Length = 8 |
+----------------+---------------+
| Value=0x0a010101 |
+----------------+---------------+
Valid Chunk Appearance
The Add IP Address parameter may only appear in the ASCONF Chunk
type.
3.2.2 Delete IP Address
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type =0xC002 | Length = Variable |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ASCONF-Request Correlation ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Address Parameter |
Stewart et.al. [Page 6]
Internet Draft SCTP Dynamic Address Reconfiguration May 2002
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
ASCONF-Request Correlation ID: 32 bits
This is an opaque integer assigned by the sender to identify each
request parameter. It is in host byte order and is only meaningful
to the sender. The receiver of the ASCONF Chunk will copy this 32
bit value into the ASCONF Response Correlation ID field of the
ASCONF-ACK response parameter. The sender of the ASCONF can use this
same value in the ASCONF-ACK to find which request the response is
for.
Address Parameter: TLV
This field contains an IPv4 or IPv6 address parameter as described in
3.3.2.1 of [RFC2960]. The complete TLV is wrapped within this
parameter. It informs the receiver that the address specified is to
be removed from the existing association.
An example TLV deleting the IPv4 address 10.1.1.1 from an existing
association would look as follows:
+--------------------------------+
| Type=0xC002 | Length = 16 |
+--------------------------------+
| C-ID = 0x01023476 |
+--------------------------------+
| Type=5 | Length = 8 |
+----------------+---------------+
| Value=0x0a010101 |
+----------------+---------------+
Valid Chunk Appearance
The Delete IP Address parameter may only appear in the ASCONF Chunk
type.
3.2.3 Error Cause Indication
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = 0xC003 | Length = Variable |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ASCONF-Response Correlation ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Error Cause(s) or Return Info on Success |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
ASCONF-Response Correlation ID: 32 bits
Stewart et.al. [Page 7]
Internet Draft SCTP Dynamic Address Reconfiguration May 2002
This is an opaque integer assigned by the sender to identify each
request parameter. The receiver of the ASCONF Chunk will copy this 32
bit value from the ASCONF-Request Correlation ID into the ASCONF
Response Correlation ID field so the peer can easily correlate the
request to this response.
Error Cause(s): TLV(s)
When reporting an error this response parameter is used to wrap
one or more standard error causes normally found within an SCTP
Operational Error or SCTP Abort (as defined in [RFC2960]). The
Error Cause(s) follow the format defined in section 3.3.10 of
[RFC2960].
Valid Chunk Appearance
The Error Cause Indication parameter may only appear in the
ASCONF-ACK chunk type.
3.2.4 Set Primary IP Address
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type =0xC004 | Length = Variable |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ASCONF-Request Correlation ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Address Parameter |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
ASCONF-Request Correlation ID: 32 bits
This is an opaque integer assigned by the sender to identify each
request parameter. It is in host byte order and is only meaningful
to the sender. The receiver of the ASCONF Chunk will copy this 32
bit value into the ASCONF Response Correlation ID field of the
ASCONF-ACK response parameter. The sender of the ASCONF can use this
same value in the ASCONF-ACK to find which request the response is
for.
Address Parameter: TLV
This field contains an IPv4 or IPv6 address parameter as described in
3.3.2.1 of [RFC2960]. The complete TLV is wrapped within this
parameter. It requests the receiver to mark the specified address
as the primary address to send data to (see section 5.1.2 of
[RFC2960]). The receiver MAY mark this as its primary upon
receiving this request.
An example TLV requesting that the IPv4 address 10.1.1.1 be made the
primary destination address would look as follows:
Stewart et.al. [Page 8]
Internet Draft SCTP Dynamic Address Reconfiguration May 2002
+--------------------------------+
| Type=0xC004 | Length = 18 |
+--------------------------------+
| C-ID = 0x01023479 |
+--------------------------------+
| Type=5 | Length = 8 |
+----------------+---------------+
| Value=0x0a010101 |
+----------------+---------------+
Valid Chunk Appearance
The Set Primary IP Address parameter may appear in the ASCONF Chunk,
the INIT, or the INIT-ACK chunk type. The inclusion of this parameter
in the INIT or INIT-ACK can be used to indicate an initial preference
of primary address.
3.2.5 Success Indication
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = 0xC005 | Length = 8 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ASCONF-Response Correlation ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
By default if a responding endpoint does not report an error for any
requested TLV, a success is implicitly indicated. Thus a sender of a
ASCONF-ACK MAY indicate complete success of all TLVs in an ASCONF by
returning only the Chunk Type, Chunk Flags, Chunk Length (set to 8)
and the Serial Number.
The responding endpoint MAY also choose to explicitly report a
success for a requested TLV, by returning a success report ASCONF
Parameter Response.
ASCONF-Response Correlation ID: 32 bits
This is an opaque integer assigned by the sender to identify each
request parameter. The receiver of the ASCONF Chunk will copy this 32
bit value from the ASCONF-Request Correlation ID into the ASCONF
Response Correlation ID field so the peer can easily correlate the
request to this response.
Valid Chunk Appearance
The Success Indication parameter may only appear in the ASCONF-ACK
chunk type.
Stewart et.al. [Page 9]
Internet Draft SCTP Dynamic Address Reconfiguration May 2002
3.2.6 Adaption Layer Indication
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type =0xC006 | Length = Variable |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Reserved Bit Fields |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
This parameter is specified for the communication of peer upper
layer protocols. It is envisioned to be used for flow control
and other adaption layers that require an indication to be
carried in the INIT and INIT-ACK. Each adaption layer that
is defined that wishes to use this parameter MUST specify
a bit in the reserved bit field in an appropriate RFC. This
parameter SHOULD NOT be examined by the receiving SCTP
implementation and should be passed opaquely to the upper
layer protocol.
Valid Chunk Appearance
The Adaption Layer Indication parameter may appear in INIT or
INIT-ACK chunk and SHOULD be passed to the receivers upper layer
protocol.
3.3 New Error Causes
Four new Error Causes are added to the SCTP Operational Errors,
primarily for use in the ASCONF-ACK chunk.
Cause Code
Value Cause Code
--------- ----------------
0x000B Request to Delete Last Remaining IP Address.
0x000C Operation Refused Due to Resource Shortage.
0x000D Request to Delete Source IP Address.
0x000E Association Aborted due to illegal ASCONF-ACK
Table 3: New Error Causes
3.3.1 Error Cause: Request to Delete Last Remaining IP Address
Cause of error
---------------
Request to Delete Last Remaining IP address: The receiver of this
error sent a request to delete the last IP address from its
association with its peer. This error indicates that the request is
rejected.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Cause Code=0x000B | Cause Length=Variable |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Stewart et.al. [Page 10]
Internet Draft SCTP Dynamic Address Reconfiguration May 2002
\ TLV-Copied-From-ASCONF /
/ \
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
An example of a failed delete in an Error Cause TLV would look as
follows in the response ASCONF-ACK message:
+--------------------------------+
| Type = 0xC003 | Length = 24 |
+--------------------------------+
| C-ID = 0x01023476 |
+--------------------------------+
| Cause=0x000B | Length = 16 |
+----------------+---------------+
| Type= 0xC002 | Length = 12 |
+----------------+---------------+
| Type=0x0005 | Length = 8 |
+----------------+---------------+
| Value=0x0A010101 |
+----------------+---------------+
3.3.2 Error Cause: Operation Refused Due to Resource Shortage
Cause of error
---------------
This error cause is used to report a failure by the receiver to
perform the requested operation due to a lack of resources. The
entire TLV that is refused is copied from the ASCONF into the
error cause.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Cause Code=0x000C | Cause Length=Variable |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
\ TLV-Copied-From-ASCONF /
/ \
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
An example of a failed addition in an Error Cause TLV would look as
follows in the response ASCONF-ACK message:
+--------------------------------+
| Type = 0xC003 | Length = 24 |
+--------------------------------+
| C-ID = 0x01023474 |
+--------------------------------+
| Cause=0x000C | Length = 16 |
+----------------+---------------+
| Type=0xC001 | Length = 12 |
+--------------------------------+
| Type=0x0005 | Length = 8 |
+----------------+---------------+
| Value=0x0A010101 |
Stewart et.al. [Page 11]
Internet Draft SCTP Dynamic Address Reconfiguration May 2002
+----------------+---------------+
3.3.3 Error Cause: Request to Delete Source IP Address
Cause of error
---------------
Request to Delete Source IP Address: The receiver of this error sent
a request to delete the source IP address of the ASCONF
message. This error indicates that the request is rejected.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Cause Code=0x000D | Cause Length=Variable |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
\ TLV-Copied-From-ASCONF /
/ \
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
An example of a failed delete in an Error Cause TLV would look as
follows in the response ASCONF-ACK message:
+--------------------------------+
| Type = 0xC003 | Length = 24 |
+--------------------------------+
| C-ID = 0x01023476 |
+--------------------------------+
| Cause=0x000D | Length = 16 |
+----------------+---------------+
| Type=0xC002 | Length = 12 |
+----------------+---------------+
| Type=0x0005 | Length = 8 |
+----------------+---------------+
| Value=0x0A010101 |
+----------------+---------------+
IMPLEMENTATION NOTE: It is unlikely that an endpoint would source
a packet from the address being deleted, unless the endpoint
does not do proper source address selection.
3.3.4 Error Cause: Association Aborted due to illegal ASCONF-ACK
This error is to be included in an ABORT that is generated due
to the reception of an ASCONF-ACK that was not expected but
would have been the next correct ASCONF-ACK (see section
4.3 rule D0).
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Cause Code=0x000E | Cause Length=4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
4. Procedures
This section will lay out the specific procedures for address
configuration change chunk type and its processing.
Stewart et.al. [Page 12]
Internet Draft SCTP Dynamic Address Reconfiguration May 2002
4.1 ASCONF Chunk Procedures
When an endpoint has an ASCONF signaled change to be sent to the
remote endpoint it should do the following:
A1) Create an ASCONF Chunk as defined in section 3.1.1. The chunk
should contain all of the TLV(s) of information necessary to be
sent to the remote endpoint, and unique correlation identities for
each request.
A2) A serial number should be assigned to the Chunk. The serial
number should be a monotonically increasing number. All serial
numbers are defined to be initialized at the start of the
association to the same value as the Initial TSN and are incremented
by one.
A3) If no ASCONF Chunk is outstanding (un-acknowledged) with the
remote peer, send the chunk.
A4) Start a T-4 RTO timer, using the RTO value of the selected
destination address (normally the primary path; see [RFC2960] section
6.4 for details).
A5) When the ASCONF-ACK that acknowledges the serial number last
sent arrives, stop the T-4 RTO timer, and clear the appropriate
association and destination error counters as defined in [RFC2960]
section 8.1 and 8.2.
A6) Process all of the TLVs within the ASCONF-ACK to find out
particular status information returned to the various requests that
were sent. Use the Correlation IDs to correlate the request and the
responses.
A7) If an error response is received for a TLV parameter,
all TLVs with no response before the failed TLV are considered
successful if not reported. All TLVs after the failed response are
considered unsuccessful unless a specific success indication is
present for the parameter.
A8) If there is no response(s) to specific TLV parameter(s), and no
failures are indicated, then all request(s) are considered
successful.
A9) If the peer responds to a ASCONF with an unrecognized chunk type,
the sender of the ASCONF MUST NOT send any further ASCONF chunks and
MUST stop its T-4 timer.
If the T-4 RTO timer expires the endpoint should do the following:
B1) Increment the error counters and perform path failure detection
on the appropriate destination address as defined in [RFC2960]
section 8.1 and 8.2.
B2) Increment the association error counters and perform endpoint
Stewart et.al. [Page 13]
Internet Draft SCTP Dynamic Address Reconfiguration May 2002
failure detection on the association as defined in [RFC2960] section
8.1 and 8.2.
B3) Back-off the destination address RTO value to which the ASCONF
chunk was sent by doubling the RTO timer value.
Note: The RTO value is used in the setting of all timer types
for SCTP. Each destination address has a single RTO estimate.
B4) Re-transmit the ASCONF Chunk last sent and if possible choose an
alternate destination address (please refer to [RFC2960] section
6.4.1). An endpoint MUST NOT add new parameters to this chunk, it
MUST be the same (including its serial number) as the last ASCONF
sent.
B5) Restart the T-4 RTO timer. Note that if a different destination is
selected, then the RTO used will be that of the new destination
address.
Note: the total number of re-transmissions is limited by B2
above. If the maximum is reached, the association will fail and enter
a CLOSED state (see [RFC2960] section 6.4.1 for details).
4.1.1 Congestion Control of ASCONF Chunks
In defining the ASCONF Chunk transfer procedures, it is essential
that these transfers MUST NOT cause congestion within the network.
To achieve this, we place these restrictions on the transfer of
ASCONF Chunks:
R1) One and only one ASCONF Chunk MAY be in transit and
unacknowledged at any one time. If a sender, after sending an ASCONF
chunk, decides it needs to transfer another ASCONF Chunk, it MUST
wait until the ASCONF-ACK Chunk returns from the previous ASCONF
Chunk before sending a subsequent ASCONF. Note this restriction
binds each side, so at any time two ASCONF may be in-transit on any
given association (one sent from each endpoint).
R2) An ASCONF may be bundled with any other chunk type (except other
ASCONF Chunks).
R3) An ASCONF-ACK may be bundled with any other chunk type except
other ASCONF-ACKs.
R4) Both ASCONF and ASCONF-ACK chunks MUST NOT be sent in any SCTP
state except ESTABLISHED.
R5) An ASCONF MUST NOT be larger than the path MTU of the destination.
R6) An ASCONF-ACK SHOULD not be larger than the path MTU. In some
circumstances an ASCONF-ACK may exceed the path MTU and in such
a case IP fragmentation must be used.
If the sender of an ASCONF Chunk receives an Operational Error
Stewart et.al. [Page 14]
Internet Draft SCTP Dynamic Address Reconfiguration May 2002
indicating that the ASCONF chunk type is not understood, then the
sender MUST not send subsequent ASCONF Chunks to the peer. The
endpoint should also inform the upper layer application that the
peer endpoint does not support any of the extensions detailed in this
document.
4.2 Upon reception of an ASCONF Chunk.
When an endpoint receives an ASCONF Chunk from the remote peer
special procedures MAY be needed to identify the association
the ASCONF Chunk is associated with. To properly find the
association the following procedures should be followed:
L1) Use the source address and port number of the sender to
attempt to identify the association (i.e. use the same method
defined in [RFC2960] used for all other SCTP chunks ). If found
proceed to rule L4.
L2) If the association is not found, use the address found
in the Address Bytes field combined with the port number
found in the SCTP common header. If found proceed to rule
L4.
L3) If neither L1 or L2 locates the association, treat
the chunk as an Out Of The Blue chunk as defined in
[RFC2960].
L4) Follow the normal rules to validate the SCTP verification
tag found in [RFC2960].
After identification and verification of the association,
the following should be performed to properly process the ASCONF Chunk:
C1) Compare the value of the serial number to the value the endpoint
stored in a new association variable 'Peer-Serial-Number'. This
value MUST be initialized to the Initial TSN value minus 1.
C2) If the value found in the serial number is equal to the
('Peer-Serial-Number' + 1), the endpoint MUST:
V1) Process the TLVs contained within the Chunk performing the
appropriate actions as indicated by each TLV type. The TLVs MUST
be processed in order within the Chunk. For example, if the sender
puts 3 TLVs in one chunk, the first TLV (the one closest to the
Chunk Header) in the Chunk MUST be processed first. The next TLV in
the chunk (the middle one) MUST be processed second and finally the
last TLV in the Chunk MUST be processed last.
V2) In processing the chunk, the receiver should build a response
message with the appropriate error TLVs, as specified in the
Parameter type bits for any ASCONF Parameter it does not understand.
To indicate an unrecognized parameter, cause type 8 as defined
in the INIT-ACK in 3.3.10.8 of [RFC2960] should be used. The
Stewart et.al. [Page 15]
Internet Draft SCTP Dynamic Address Reconfiguration May 2002
endpoint may also use the response to carry rejections for other
reasons such as resource shortages etc using the Error Cause TLV and
an appropriate error condition.
Note: a positive response is implied if no error is indicated by the
sender.
V3) All error responses MUST copy the ASCONF-Request Correlation ID
field received in the ASCONF, from the TLV being responded to, into
the ASCONF-Request Correlation ID field. The ASCONF-Request
Correlation ID always precedes the request TLV. Note that a
TLV sent in an ASCONF-ACK MUST be accompanied by a Correlation ID
and a Correlation ID MUST NOT be sent without a TLV i.e. the two
are atomic.
V4) After processing the entire Chunk, it MUST send all TLVs for
both unrecognized parameters and any other status TLVs inside the
ASCONF-ACK chunk that acknowledges the arrival and processing of the
ASCONF Chunk.
V5) Update the 'Peer-Serial-Number' to the value found in the serial
number field.
C3) If the value found in the serial number is equal to the value
stored in the 'Peer-Serial-Number', the endpoint should:
X1) Parse the ASCONF Chunk TLVs but the endpoint MUST NOT take any
action on the TLVs parsed (since it has already performed these
actions).
X2) Build a response message with the appropriate response TLVs
as specified in the ASCONF Parameter type bits, for any
parameter it does not understand or could not process.
X3) After parsing the entire Chunk, it MUST send any response
TLV errors and status with an ASCONF-ACK chunk acknowledging the
arrival and processing of the ASCONF Chunk.
X4) The endpoint MUST NOT update its 'Peer-Serial-Number'.
Note: the response to the retransmitted ASCONF MUST be the same
as the original response. This MAY mean an implementation must
keep state in order to respond with the same exact answer
(including resource considerations that may have made the
implementation refuse a request).
IMPLEMENTATION NOTE: As an optimization a receiver may wish to save
the last ASCONF-ACK for some predetermined period of time and
instead of re-processing the ASCONF (with the same serial number) it
may just re-transmit the ASCONF-ACK. It may wish to use the arrival
of a new serial number to discard the previously saved ASCONF-ACK or
any other means it may choose to expire the saved ASCONF-ACK.
C4) Otherwise, the ASCONF Chunk is discarded since it must be either
Stewart et.al. [Page 16]
Internet Draft SCTP Dynamic Address Reconfiguration May 2002
a stale packet or from an attacker. A receiver of such a packet MAY
log the event for security purposes.
C5) In both cases C2 and C3 the ASCONF-ACK MUST be sent back to the
source address contained in the IP header of the ASCONF being
responded to.
4.3 General rules for address manipulation
When building TLV parameters for the ASCONF Chunk that
will add or delete IP addresses the following rules should be
applied:
D0) If an endpoint receives an ASCONF-ACK but no ASCONF chunk
is outstanding the endpoint MUST ABORT the association.
D1) When adding an IP address to an association, the IP address is
NOT considered fully added to the association until the ASCONF-ACK
arrives. This means that until such time as the ASCONF containing
the add is acknowledged the sender MUST NOT use the new IP address
as a source for ANY SCTP packet except on carrying an ASCONF chunk.
The receiver of the add IP address request may use the
address as a destination immediately.
D2) After the ASCONF-ACK of an IP address add arrives, the
endpoint MAY begin using the added IP address as a source
address for any type of SCTP chunk.
D3a) If an endpoint receives an Error Cause TLV indicating that the
IP address Add or IP address Deletion parameters was not understood,
the endpoint MUST consider the operation failed and MUST NOT attempt
to send any subsequent Add or Delete requests to the peer.
D3b) If an endpoint receives an Error Cause TLV indicating that the
IP address Set Primary IP Address parameter was not understood,
the endpoint MUST consider the operation failed and MUST NOT attempt
to send any subsequent Set Primary IP Address requests to the peer.
D4) When deleting an IP address from an association, the IP address
MUST be considered a valid destination address for the reception of
SCTP packets until the ASCONF-ACK arrives and MUST NOT be used as a
source address for any subsequent packets. This means that any
datagrams that arrive before the ASCONF-ACK destined to the IP address
being deleted MUST be considered part of the current
association. One special consideration is that ABORT chunks arriving
destined to the IP address being deleted MUST be ignored (see
Section 4.3.1 for further details).
D5) An endpoint MUST NOT delete its last remaining IP address from an
association. In other words if an endpoint is NOT multi-homed it
MUST NOT use the delete IP address without an add IP address preceding
the delete parameter in the ASCONF chunk. Or if an endpoint sends
multiple requests to delete IP addresses it MUST NOT delete all
Stewart et.al. [Page 17]
Internet Draft SCTP Dynamic Address Reconfiguration May 2002
of the IP addresses that the peer has listed for the requester.
D6) An endpoint MUST NOT set an IP header source address for an SCTP
packet holding the ASCONF Chunk to be the same as an address being
deleted by the ASCONF Chunk.
D7) If a request is received to delete the last remaining IP address
of a peer endpoint, the receiver MUST send an Error Cause TLV with
the error cause set to the new error code 'Request to Delete Last
Remaining IP Address'. The requested delete MUST NOT be performed or
acted upon, other than to send the ASCONF-ACK.
D8) If a request is received to delete an IP address which is also
the source address of the IP packet which contained the ASCONF
chunk, the receiver MUST reject this request. To reject the request
the receiver MUST send an Error Cause TLV set to the new error code
'Request to Delete Source IP Address' (unless Rule D5 has also been
violated, in which case the error code 'Request to Delete Last
Remaining IP Address' is sent).
D9) If an endpoint receives an ADD IP address request and does not
have the local resources to add this new address to the association,
it MUST return an Error Cause TLV set to the new error code
'Operation Refused Due to Resource Shortage'.
D10) If an endpoint receives an 'Out of Resource' error in response
to its request to ADD an IP address to an association, it must
either ABORT the association or not consider the address part of the
association. In other words if the endpoint does not ABORT the
association, it must consider the add attempt failed and NOT use
this address since its peer will treat SCTP packets destined to
the address as Out Of The Blue packets.
D11) When an endpoint receiving an ASCONF to add an IP address sends
an 'Out of Resource' in its response, it MUST also fail any
subsequent add or delete requests bundled in the ASCONF. The
receiver MUST NOT reject an ADD and then accept a subsequent DELETE
of an IP address in the same ASCONF Chunk. In other words, once a
receiver begins failing any ADD or DELETE request, it must fail all
subsequent ADD or DELETE requests contained in that single ASCONF.
D12) When an endpoint receives a request to delete an IP address
that is the current primary address, it is an implementation
decision as to how that endpoint chooses the new primary address.
D13) When an endpoint receives a valid request to DELETE an IP
address the endpoint MUST consider the address no longer as part of
the association. It MUST NOT send SCTP packets for the association
to that address and it MUST treat subsequent packets received from
that address as Out Of The Blue.
During the time interval between sending out the ASCONF and
receiving the ASCONF-ACK it MAY be possible to receive DATA chunks
out of order. The following examples illustrate these problems:
Stewart et.al. [Page 18]
Internet Draft SCTP Dynamic Address Reconfiguration May 2002
Endpoint-A Endpoint-Z
---------- ----------
ASCONF[Add-IP:X]------------------------------>
/--ASCONF-ACK
/
/--------/---New DATA:
/ / Destination
<-------------------/ / IP:X
/
<--------------------------/
In the above example we see a new IP address (X) being added to
the Endpoint-A. However due to packet re-ordering in the network
a new DATA chunk is sent and arrives at Endpoint-A before
the ASCONF-ACK confirming the add of the address to the association.
A similar problem exists with the deletion of an IP address as
follows:
Endpoint-A Endpoint-Z
---------- ----------
/------------New DATA:
/ Destination
/ IP:X
ASCONF [DEL-IP:X]---------/---------------->
<-----------------/------------------ASCONF-ACK
/
/
<-------------/
In this example we see a DATA chunk destined to the IP:X (which is
about to be deleted) arriving after the deletion is complete.
For the ADD case an endpoint SHOULD consider the newly adding IP
address valid for the association to receive data from during the
interval when awaiting the ASCONF-ACK. The endpoint MUST NOT source
data from this new address until the ASCONF-ACK arrives but it may
receive out of order data as illustrated and MUST NOT treat this
data as an OOTB datagram (please see [RFC2960] section 8.4). It MAY
drop the data silently or it MAY consider it part of the association
but it MUST NOT respond with an ABORT.
For the DELETE case, an endpoint MAY respond to the late arriving DATA
packet as an OOTB datagram or it MAY hold the deleting IP address for a
small period of time as still valid. If it treats the DATA packet as
an OOTB the peer will silently discard the ABORT (since by the time
the ABORT is sent the peer will have removed the IP address from this
association). If the endpoint elects to hold the IP address valid for
a period of time, it MUST NOT hold it valid longer than 2 RTO
intervals for the destination being removed.
4.3.1 A special case for OOTB ABORT chunks
Another case worth mentioning is illustrated below:
Stewart et.al. [Page 19]
Internet Draft SCTP Dynamic Address Reconfiguration May 2002
Endpoint-A Endpoint-Z
---------- ----------
New DATA:------------\
Source IP:X \
\
ASCONF-REQ[DEL-IP:X]----\------------------>
\ /---------ASCONF-ACK
\ /
\----/-----------> OOTB
(Ignored <---------------------/-------------ABORT
by rule D4) /
<---------------------/
For this case, during the deletion of an IP address, an
Abort MUST be ignored if the destination address of the
Abort message is that of a destination being deleted.
4.3.2 A special case for changing an address.
In some instances the sender may only have one IP address in an
association that is being renumbered. When this occurs, the sender
may not be able to send to the peer the appropriate ADD/DELETE pair
and use the old address as a source in the IP header. For this
reason the sender MUST fill in the Address Bytes field with an
address that is part of the association (in this case the one being
deleted). This will allow the receiver to locate the association
without using the source address found in the IP header.
The receiver of such a chunk MUST always first use the source address
found in the IP header in looking up the association. The
receiver should attempt to use the address found in the Address
Bytes field only if the lookup fails using the source address from
the IP header. The receiver MUST reply to the source address
of the packet in this case which is the new address that
was added by the ASCONF (since the old address is no longer a part
of the association after processing).
4.4 Setting of the primary address
A sender of this option may elect to send this combined with
a deletion or addition of an address. A sender SHOULD only send
a set primary request to an address that is already considered
part of the association. In other words if a sender combines
a set primary with an add of a new IP address the set primary
will be discarded unless the add request is to be processed
BEFORE the set primary (i.e. it precedes the set primary).
A request to set primary MAY also appear in an INIT or INIT-ACK
chunk. This can give advice to the peer endpoint as to which
of its addresses the sender of the INIT or INIT-ACK would prefer
to be used as the primary address.
Stewart et.al. [Page 20]
Internet Draft SCTP Dynamic Address Reconfiguration May 2002
The request to set an address as the primary path is an option the
receiver SHOULD perform. It is considered advice to the receiver of
the best destination address to use in sending SCTP packets (in the
requesters view). If a request arrives that asks the receiver to
set an address as primary that does not exist, the receiver should
NOT honor the request, leaving its existing primary address
unchanged.
5. Abstract description of SCTP addressing
The following text provides a working definitions to discuss
addIP. We need to distinguish a list of IP addresses and a wildcard
address. This corresponds to binding a set of addresses or binding
the wildcard INADDR_ANY in a sockets API. Using this notation we can
thus state the rules for using add-ip.
A host is a set of IP addresses H={IP1, ..., IPN}
An sock-endpoint at a host H is a pair of a set of IP addresses and
a port number:
sE = ({IP1, ..., IPn}, Port) where either {IP1, ..., IPn} is a
subset of H or n=1 and IP1 = Wildcard (we abbreviate wildcard as
'*').
Note: do not confuse sock-endpoint with RFC2960 endpoint definition.
They are logically different. In order to make them equivalent
no wildcards must be used and the subset selected must always
be the whole set i.e.:
If sE = ({IP1, ..., IPn}, Port} is a sock-endpoint and A is an
association for which sE is an sock-endpoint, then
Addr(sE, A) = {IP1, ..., IPn}.
In this special case a sock-endpoint is an endpoint in the sense
of RFC2960.
The set of IP addresses of an sock-endpoint is defined as Addr(sE) =
{IP1, ..., IPn}.
The port number of sE is defined as Port(sE) = Port.
Sock-Endpoint(H,Port) denotes the set of all sock-endpoints with
port 'Port'.
For two different sock-endpoints sE' and sE'' at the same host with
the same port number Addr(sE') <> {Wildcard} <> Addr(sE'') holds and
Addr(sE') and Addr(sE'') are disjoint.
This means that exactly one of the following is true:
Sock-Endpoint(H,Port) is
- empty
Stewart et.al. [Page 21]
Internet Draft SCTP Dynamic Address Reconfiguration May 2002
- contains one Element sE with Addr(sE)={Wildcard}
- contains more than one Element where Addr(sE) <> {Wildcard} and
all Addr(sE) are disjoin
While establishing an association A between endpoints sE' and sE''
at host H' and H'' two subsets are defined: Addr(sE',A) and
Addr(sE'',A).
Addr(sE',A) is defined:
If Addr(sE') is the {Wildcard} then
Addr(sE',A) is a subset of H'
else
Addr(sE',A) is subset of Addr(sE')
The subset may be defined by scoping of the addresses set for
routeablility.
Addr(sE,A) thus describes the set of IP addresses of E used for A
(Note this definition is the canonical endpoint represented in
[RFC2960]).
This is because Addr(sE',A) is what sE' sends in its INIT/INIT-ACK
to sE'' and Addr(sE'',A) is what sE'' sends in its INIT/INIT-ACK to
sE'. This is consistent with RFC2960. When you perform either add-ip
or delete-ip later on in the life of the association, you are simply
modifying Addr(sE',A) and Addr(sE'',A).
Association establishment between sE' and sE'' can be seen as:
1. sE' and sE'' do exist before the association. The same is thus
true for H' and H''. Therefore Addr(sE') and Addr(sE'') are known.
This corresponds to sockets bound to some addresses or INADDR_ANY.
Note: the binding function can be either specific or wildcarded.
When it is specific we have, Addr(sE') <= H'; where "=" happens when
we specifically bind every addresses of H' to sE'. When it is
wildcarded we have, Addr(sE') == H'; A wildcard is resolved at the
point of time when an association is established.
2. When an association is setup between a pair of endpoints the
following is performed:
A. Introduce a temporary Set S' and S'' where:
If Addr(sE') is the wildcard
S' = H'
else
S' = Addr(sE')
B. Replace S' by a subset of S' by some limitation (address
scoping for example). So S' <= Addr(sE'); In some cases
this may not reduce the set of addresses.
Stewart et.al. [Page 22]
Internet Draft SCTP Dynamic Address Reconfiguration May 2002
In other words S' is a subset (or full-set) of Addr(sE'),
determined by applying some specific limitation/scoping rules
to Addr(sE') at a specific point in time.
The same is true for S''.
C. S' and S'' are the addresses used by the association. So if sE' is
the client (the one sending the INIT), you generate S' first and
then, send the INIT using the generated address set S'.
3. After the association has been established Addr(sE', A) = S' and
Addr(sE'',A) = S'' for this association.
Thus the correct definition is the following:
An association is a pair of pairs A=((sE', S'), (sE'',S'')). We
define Addr(sE',A)=S' with the restriction that Addr(sE',A) is a
subset of Addr(sE') if Addr(sE') is not the wildcard. If Addr(sE')
is the wildcard then Addr(sE',A) is a subset of H'.
The following are the rules that can then be applied when using
add-ip with these definition:
R1) If Addr(sE) = {Wildcard} then when H gets a new element, it is
automatically added to sE.
R1.1) You MAY add that address to Addr(sE, A) for all associations
where sE belongs to A using an ASCONF.
R2) If Addr(sE) <> {Wildcard} you can explicitly add an Address of H
(possibly a new one) to Addr(sE) if this address is not an Element
of Addr(sE') for all sE <> sE' in Endpoint(H, Port(E)).
R2.1) You MAY add that address to Addr(sE, A) for all associations
where sE belongs to A using an ASCONF.
R3) An address may be deleted from Addr(sE,A) reducing S' to a
smaller sub-set.
R4) An address may be deleted from endpoint E with the following
considerations:
If Addr(sE) = {*} then
any address of Addr(sE,A) can be removed anytime.
else
An address can be removed from sE only after it has
been removed form all associations sE belongs to.
Note that during the removal of an address (before all
associations have removed the address for Addr(sE,A)) an
endpoint sE SHOULD NOT put the address being deleted in
any new S' chosen for new associations.
Stewart et.al. [Page 23]
Internet Draft SCTP Dynamic Address Reconfiguration May 2002
R5) You can delete an address from H only after it has been removed
from all socket-endpoints at host H.
Note that R5) applies to the logical removal of the address
from a host NOT the physical removal. When an address is
physically removed, it stays logically a part of the host
until it is removed from all socket-endpoints and associations.
During this period the selection for S' MUST be modified NOT
to include the address being removed.
6. Security Considerations
The ADD/DELETE of an IP address to an existing association does
provide an additional mechanism by which existing associations can
be hijacked. Where the attacker is able to intercept and or alter
the packets sent and received in an association, the use of this
feature MAY increase the ease with which an association may be
overtaken. This threat SHOULD be considered when deploying a version
of SCTP that makes use of this feature. The IP Authentication Header
[RFC2402] SHOULD be used when the threat environment requires
stronger integrity protections, but does not require
confidentiality. It should be noted that in the base SCTP
specification [RFC2960], if an attacker is able to intercept and or
alter packets, even without this feature it is possible to hijack an
existing association; please refer to Section 11 of RFC2960.
7. IANA considerations
This document defines the following new SCTP parameters, chunks
and errors:
- Two new chunk types,
- Six parameter types, and
- Three new SCTP error causes.
8. Acknowledgments
The authors wish to thank Jon Berger, Peter Lei, John Loughney, Ivan
Arias Rodriguez, Renee Revis, Marshall Rose, and Chip Sharp for
their invaluable comments.
9. Authors' Addresses
Randall R. Stewart Tel: +1-815-477-2127
Cisco Systems, Inc. EMail: rrs@cisco.com
8745 W. Higgins Road, Suite 200
Chicago, Ill 60631
USA
Micheal A. Ramalho Tel: +1-732-809-0188
Cisco Systems, Inc. EMail: mramalho@cisco.com
1802 Rue de la Porte
Wall Township, NJ 0719-3784
Stewart et.al. [Page 24]
Internet Draft SCTP Dynamic Address Reconfiguration May 2002
Qiaobing Xie Tel: +1-847-632-3028
Motorola, Inc. EMail: qxie1@email.mot.com
1501 W. Shure Drive, #2309
Arlington Heights, IL 60004
USA
Michael Tuexen Tel: +49-89-722-47210
SIEMENS AG EMail: Michael.Tuexen@icn.siemens.de
Hofmannstr. 51
81359 Munich
Germany
Ian Rytina Tel: +61-3-9301-6164
Ericsson Australia EMail:ian.rytina@ericsson.com
37/360 Elizabeth Street
Melbourne, Victoria 3000
Australia
Maria-Carmen Belinchon
EMail:emecbv@madrid.es.eu.ericsson.se
Phil Conrad Tel: +1-215-204-7910
Netlab Research Group Email conrad@acm.org
Dept. Of Computer &
Information Sciences
Temple University
1805 N Broad St.
Philadelphia, PA 19122
USA
10. Normative References
[RFC2960] R. R. Stewart, Q. Xie, K. Morneault, C. Sharp,
H. J. Schwarzbauer, T. Taylor, I. Rytina, M. Kalla, L. Zhang,
and, V. Paxson, "Stream Control Transmission Protocol," RFC
2960, October 2000.
[RFC2026] Bradner, S., "The Internet Standards Process -- Revision
3", RFC 2026, October 1996.
[RFC2119] Bradner, S. "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2402] S. Kent, R. Atkinson., "IP Authentication Header.", RFC
2402, November 1998.
This Internet Draft expires in 6 months from May, 2001
Stewart et.al. [Page 25]
Internet Draft SCTP Dynamic Address Reconfiguration May 2002
Stewart et.al. [Page 26]