CoRE Working Group B. Silverajan
Internet-Draft Tampere University of Technology
Intended status: Informational T. Savolainen
Expires: June 20, 2015 Nokia
December 17, 2014
CoAP Communication with Alternative Transports
draft-silverajan-core-coap-alternative-transports-07
Abstract
CoAP has been standardised as an application level REST-based
protocol. A single CoAP message is typically encapsulated and
transmitted using UDP or DTLS as transports. These transports are
optimal solutions for CoAP use in IP-based constrained environments
and nodes. However compelling motivation exists for understanding
how CoAP can operate with other transports, such as the need for M2M
communication using non-IP networks, improved transport level end-to-
end reliability and security, NAT and firewall traversal issues, and
mechanisms possibly incurring a lower overhead to CoAP/HTTP
translation gateways. This draft examines the requirements for
conveying CoAP messages to end points over such alternative
transports. It also provides a new URI format for representing CoAP
resources over alternative transports.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on June 20, 2015.
Copyright Notice
Copyright (c) 2014 IETF Trust and the persons identified as the
document authors. All rights reserved.
Silverajan & Savolainen Expires June 20, 2015 [Page 1]
Internet-Draft CoAP Alternative Transports December 2014
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
2. Usage Cases . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.1. Use of SMS . . . . . . . . . . . . . . . . . . . . . . . 4
2.2. Use of WebSockets . . . . . . . . . . . . . . . . . . . . 4
2.3. Use of P2P Overlays . . . . . . . . . . . . . . . . . . . 4
2.4. Use of TCP and TLS . . . . . . . . . . . . . . . . . . . 4
2.5. Others . . . . . . . . . . . . . . . . . . . . . . . . . 5
3. Node Types based on Transport Availability . . . . . . . . . 5
4. CoAP Alternative Transport URI . . . . . . . . . . . . . . . 6
4.1. Design Considerations . . . . . . . . . . . . . . . . . . 7
4.2. URI format . . . . . . . . . . . . . . . . . . . . . . . 8
5. Alternative Transport Analysis and Properties . . . . . . . . 9
6. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 12
7. Security Considerations . . . . . . . . . . . . . . . . . . . 12
8. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 12
9. References . . . . . . . . . . . . . . . . . . . . . . . . . 12
9.1. Normative References . . . . . . . . . . . . . . . . . . 12
9.2. Informative References . . . . . . . . . . . . . . . . . 12
Appendix A. Expressing transport in the URI in other ways . . . 15
A.1. Transport information as part of the URI authority . . . 15
A.1.1. Usage of DNS records . . . . . . . . . . . . . . . . 16
A.2. Making CoAP Resources Available over Multiple Transports 16
A.3. Transport as part of a 'service:' URL scheme . . . . . . 18
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 19
1. Introduction
The Constrained Application Protocol (CoAP) [RFC7252] has been
standardised by the CoRE WG as a lightweight, HTTP-like protocol
providing a request/response model that constrained nodes can use to
communicate with other nodes, be those servers, proxies, gateways,
less constrained nodes, or other constrained nodes.
As the Internet continues taking shape by integrating new kinds of
networks, services and devices, the need for a consistent,
lightweight method for resource representation, retrieval and
Silverajan & Savolainen Expires June 20, 2015 [Page 2]
Internet-Draft CoAP Alternative Transports December 2014
manipulation becomes evident. Owing to its simplicity and low
overhead, CoAP is a highly suitable protocol for this purpose.
However, the CoAP endpoint can reside in a non-IP network, be
separated from its peer by NATs and firewalls or simply has no
possibility to communicate over UDP. Consequently in addition to
UDP, alternative transport channels for conveying CoAP messages could
be considered.
Extending CoAP over alternative transports allows implementations to
have a significantly larger relevance in constrained as well as non-
constrained networked environments. It leads to better code
optimisation in constrained nodes and broader implementation reuse
across new transport channels. As opposed to implementing new
resource retrieval mechanisms, an application in an end-node can
continue relying on using CoAP's REST-based resource retrieval and
manipulation for this purpose, while changes in end point
identification and the transport protocol can be addressed by a
transport-specific messaging sublayer. This simplifies development
and memory requirements. Resource representations are also visible
in an end-to-end manner for any CoAP client. The processing and
computational overhead for conveying CoAP Requests and Responses from
one underlying transport to another, would be less than that of an
application-level gateway performing protocol translation of
individual messages between CoAP and another resource retrieval
protocol such as HTTP.
This document first provides scenarios where usage of CoAP over
alternative transports is either currently underway, or may prove
advantageous in the future. A simple transport type classification
for CoAP-capable nodes is provided next. Then a new URI format is
described through which a CoAP resource representation can be
formulated that expresses transport identification in addition to
endpoint information and resource paths. Following that, a
discussion of the various transport properties which influence how
CoAP Requests and Responses are mapped to transport level payloads,
is presented.
This document however, does not touch on application QoS
requirements, user policies or network adaptation, nor does it
advocate replacing the current practice of UDP-based CoAP
communication.
2. Usage Cases
Apart from UDP and DTLS, CoAP usage is being specified for the
following environments as of this writing:
Silverajan & Savolainen Expires June 20, 2015 [Page 3]
Internet-Draft CoAP Alternative Transports December 2014
2.1. Use of SMS
CoAP Request and Response messages can be sent via SMS between CoAP
end-points in a cellular network [I-D.becker-core-coap-sms-gprs]. A
CoAP Request message can also be sent via SMS from a CoAP client to a
sleeping CoAP Server as a wake-up mechanism and trigger communication
via IP. The Open Mobile Alliance (OMA) specifies both UDP and SMS as
transports for M2M communication in cellular networks. The OMA
Lightweight M2M protocol being drafted uses CoAP, and as transports,
specifies both UDP binding as well as Short Message Service (SMS)
bindings [OMALWM2M] for the same reason. For securing end-to-end
communication between Mobile Stations, the use of DTLS-encoded CoAP
messages over SMS is also being proposed
[I-D.fossati-dtls-over-gsm-sms].
2.2. Use of WebSockets
The WebSocket protocol is being proposed as a transport channel
between WebSocket enabled CoAP end-points on the Internet
[I-D.savolainen-core-coap-websockets]. This is particularly useful
as a means for web browsers, especially in smart devices, to allow
embedded client side scripts to create new WebSocket connections to
various WebSocket-enabled servers, through which CoAP Request and
Response messages can be exchanged. This also allows a browser
containing an embedded CoAP server to behave as a WebSocket client by
opening a connection to a WebSocket enabled CoAP Mirror Server
[I-D.vial-core-mirror-server] to register and update its resources.
2.3. Use of P2P Overlays
[I-D.jimenez-p2psip-coap-reload] specifices how CoAP nodes can use a
peer-to-peer overlay network called RELOAD, as a resource caching
facility for storing wireless sensor data. When a CoAP node
registers its resources with a RELOAD Proxy Node (PN), the node
computes a hash value from the CoAP URI and stores it as a structure
together with the PN's Node ID as well as the resources. Resource
retrieval by CoAP nodes is accomplished by computing the hash key
over the Request URI,opening a connection to the overlay and using
its message routing system to contact the CoAP server via its PN.
2.4. Use of TCP and TLS
Using TCP to facilitate the traversal of CoAP Request and Response
messages
[I-D.bormann-core-coap-tcp][I-D.tschofenig-core-coap-tcp-tls], allows
easier communication between CoAP clients and servers separated by
firewalls and NATs. This also allows CoAP messages to be transported
over push notification services from a notification server to a
Silverajan & Savolainen Expires June 20, 2015 [Page 4]
Internet-Draft CoAP Alternative Transports December 2014
client app on a smartphone, that may previously have subscribed to
receive change notifications of CoAP resource representations,
possibly by using CoAP Observe-functionality [I-D.ietf-core-observe].
[I-D.tschofenig-core-coap-tcp-tls] also discusses using TLS as a
transport to securely convey CoAP messages over TCP.
2.5. Others
CoAP could in addition be extended atop other transport channels,
such as:
1. The transportation of CoAP messages in Delay-Tolerant Networks
[RFC4838], using the Bundle Protocol [RFC5050] for reaching
sensors in extremely challenging environments such as acoustic,
underwater and deep space networks.
2. Any type of non-IP networks supporting constrained nodes and low-
energy sensors, such as Bluetooth and Bluetooth Low Energy
(either through L2CAP or with GATT) [BTCorev4.1], ZigBee, Z-Wave,
1-Wire, DASH7 and so on.
3. Instant Messaging and Social Networking channels, such as Jabber
and Twitter.
3. Node Types based on Transport Availability
The term "alternative transport" in this document thus far has been
used to refer to any non-UDP and non-DTLS transport that can convey
CoAP messages in its payload. A node however, may in fact possess
the capability to utilise CoAP over multiple transport channels at
its disposal, simultaneously or otherwise, at any point in time to
communicate with a CoAP end-point. Such communication can obviously
take place over UDP and DTLS as well. Inevitably, if two CoAP
endpoints reside in distinctly separate networks with orthogonal
transports, a CoAP proxy node is needed between the two networks so
that CoAP Requests and Responses can be exchanged properly.
In [RFC7228], Tables 1, 3 and 4 introduced classification schemes for
devices, in terms of their resource constraints, energy limitations
and communication power. For this document, in addition to these
capabilities, it seems useful to additionally identify devices based
on their transport capabilities.
Silverajan & Savolainen Expires June 20, 2015 [Page 5]
Internet-Draft CoAP Alternative Transports December 2014
+-------+----------------------------+
| Name | Transport Availability |
+-------+----------------------------+
| T0 | Single transport |
| | |
| T1 | Multiple transports, with |
| | one or more active at any |
| | point in time |
| | |
| T2 | Multiple active transports|
+-------+----------------------------+
Table 1: Classes of Available Transports
Nodes falling under Type T0 possess the capability of exactly 1 type
of transport channel for CoAP, at all times. These include both
active and sleepy nodes, which may choose to perform duty cycling for
power saving.
Type T1 nodes possess multiple different transports, and can retrieve
or expose CoAP resources over any or all of these transports.
However, not all transports are constantly active and certain
transport channels and interfaces could be kept in a mostly-off state
for energy-efficiency, such as when using CoAP over SMS (refer to
section 2.1)
Type T2 nodes possess more than 1 transport, and multiple transports
are simultaneously active at all times. CoAP proxy nodes which allow
CoAP endpoints from disparate transports to communicate with each
other, are a good example of this.
4. CoAP Alternative Transport URI
Based on the usage scenarios as well as the transport classes
presented in the preceding sections, this section discusses the
formulation of a new URI for representing CoAP resources over
alternative transports.
CoAP is logically divided into 2 sublayers, whereby a request/
response layer is responsible for the protocol functionality of
exchanging request and response messages, while the messaging layer
is bound to UDP. These 2 sublayers are tightly coupled, both being
responsible for properly encoding the header and body of the CoAP
message. The CoAP URI is used by both logical sublayers. For a URI
that is expressed generically as
URI = scheme ":" "//" authority path-abempty ["?"query ]
Silverajan & Savolainen Expires June 20, 2015 [Page 6]
Internet-Draft CoAP Alternative Transports December 2014
a simple example CoAP URI, "coap://server.example.com/sensors/
temperature" is interpreted as follows:
coap :// server.example.com /sensors/temperature
\___/ \______ ________/ \______ _________/
| \/ \/
protocol endpoint parameterised
identifier identifier resource
identifier
Figure 1: The CoAP URI format
The resource path is explicitly expressed, and the endpoint
identifier, which contains the host address at the network-level is
also directly bound to the scheme name containing the application-
level protocol identifier. The choice of a specific transport for a
scheme, however, cannot be embedded with a URI, but is defined by
convention or standardisation of the protocol using the scheme. As
examples, [RFC5092] defines the 'imap' scheme for the IMAP protocol
over TCP, while [RFC2818] requires that the 'https' protocol
identifier be used to differentiate using HTTP over TLS instead of
TCP.
4.1. Design Considerations
Several ways of formulating a URI which express an alternative
transport binding to CoAP, can be envisioned. When such a URI is
provided from an end-application to its CoAP implementation, the URI
component containing transport-specific information can be checked to
allow CoAP to use the appropriate transport for a target endpoint
identifier.
The following design considerations influence the formulation of a
new URI expressing CoAP resources over alternative transports:
1. A CoAP Transport URI can be supplied as a Proxy-Uri option by a
CoAP end-point to a CoAP forward proxy. This allows
communication with a CoAP end-point residing in a network using a
different transport. Section 6.4 of [RFC7252] provides an
algorithm for parsing a received URI to obtain the request's
options. Also, the generic syntax for a URI is described in
[RFC3986]. By ensuring conformance to RFC3986, the need for
custom URI parsers as well as resolution algorithms can be
obviated. In particular, a URI format needs to be described in
Silverajan & Savolainen Expires June 20, 2015 [Page 7]
Internet-Draft CoAP Alternative Transports December 2014
which each URI component clearly meets the syntax and percent-
encoding rules described.
2. Request messages sent to a CoAP endpoint using a CoAP Transport
URI may be responded to with a relative URI reference, for
example, of the form "../../path/to/resource". In such cases,
the requesting endpoint needs to resolve the relative reference
against the original CoAP Transport URI to then obtain a new
target URI to which a request can be sent to, to obtain a
resource representation. [RFC3986] provides an algorithm to
establish how relative references can be resolved against a base
URI to obtain a target URI. Given this algorithm, a URI format
needs to be described in which relative reference resolution does
not result in a target URI that loses its transport-specific
information
3. The host component of current CoAP URIs can either be an IPv4
address, an IPv6 address or a resolvable hostname. While the
usage of DNS can sometimes be useful for distinguishing transport
information (see section 4.3.1), accessing DNS over some
alternative transport environments may be challenging.
Therefore, a URI format needs to be described which is able to
represent a resource without heavy reliance on a naming
infrastructure, such as DNS.
4.2. URI format
To meet the design considerations previously discussed, the transport
information is expressed as part of the URI scheme component. This
is performed by minting new schemes for alternative transports using
the form "coap+<transport-name>" and/or "coaps+<transport-name>",
where the name of the transport is clearly and unambiguously
described. Each scheme name formed in this manner is used to
differentiate the use of CoAP, or CoAP using DTLS, over an
alternative transport respectively. The endpoint identifier, path
and query components together with each scheme name would be used to
uniquely identify each resource.
Examples of such URIs are:
o coap+tcp://[2001:db8::1]:5683/sensors/temperature for using CoAP
over TCP
o coap+tls://[2001:db8::1]:5683/sensors/temperature for using CoAP
over TLS
o coaps+sctp://[2001:db8::1]:5683/sensors/temperature for using CoAP
over DTLS over SCTP
Silverajan & Savolainen Expires June 20, 2015 [Page 8]
Internet-Draft CoAP Alternative Transports December 2014
o coap+sms://0015105550101/sensors/temperature for using CoAP over
SMS with the endpoint identifier being a telephone subscriber
number
o coaps+sms://0015105550101/sensors/temperature for using CoAP over
DTLS over SMS with the endpoint identifier being a telephone
subscriber number
o coap+ws://www.example.com/sensors/temperature for using CoAP over
WebSockets
o coap+wss://www.example.com/sensors/temperature for using CoAP over
secure WebSockets (WebSockets using TLS)
A URI of this format to distinguish transport types is simple to
understand and not dissimilar to the CoAP URI format. As the usage
of each alternative transport results in an entirely new scheme, IANA
intervention is required for the registration of each scheme name.
The registration process follows the guidelines stipulated in
[I-D.ietf-appsawg-uri-scheme-reg], particularly where permanent URI
scheme registration is concerned.
It is also entirely possible for each new scheme to specify its own
rules for how resource and transport endpoint information can be
presented. However, the URIs and resource representations arising
from their usage should meet the URI design considerations and
guidelines mentioned in this document. In addition, each new
transport being defined should take into consideration the various
transport-level properties that can have an impact on how CoAP
messages are conveyed as payload. This is elaborated on in the next
section.
5. Alternative Transport Analysis and Properties
In this section the various characteristics of alternative transports
for successfully supporting various kinds of functionality for CoAP
are considered. CoAP factors lossiness, unreliability, small packet
sizes and connection statelessness into its protocol logic. General
transport differences and their impact on carrying CoAP messages here
are discussed. Note that Properties 1, 2, and 3 are related.
Property 1: Uniqueness of an end-point identifier.
Transport protocols providing non-unique end-point IDs for nodes may
only convey a subset of the CoAP functionality. Such nodes may only
serve as CoAP servers that announce data at specific intervals to a
pre-specified end point, or to a shared medium.
Silverajan & Savolainen Expires June 20, 2015 [Page 9]
Internet-Draft CoAP Alternative Transports December 2014
Property 2: Unidirectional or bidirectional CoAP communication
support.
This refers to the ability of the CoAP end-point to use a single
transport channel for both request and response messages. Depending
on the scenario, having a unidirectional transport layer would mean
the CoAP end-point might utilise it only for outgoing data or
incoming data. Should both functionalities be needed, 2
unidirectional transport channels would be necessary.
Property 3: 1:N communication support.
This refers to the ability of the transport protocol to support
broadcast and multicast communication. CoAP's request/response
behaviour depends on unicast messaging. Group communication in CoAP
is bound to using multicasting. Therefore a protocol such as TCP
would be ill-suited for group communications using multicast.
Anycast support, where a message is sent to a well defined
destination address to which several nodes belong, on the other hand,
is supported by TCP.
Property 4: Transport-level reliability.
This refers to the ability of the transport protocol to provide a
guarantee of reliability against packet loss, ensuring ordered packet
delivery and having error control. When CoAP Request and Response
messages are delivered over such transports, the CoAP implementations
elide certain fields in the packet header. As an example, if the
usage of a connection-oriented transport renders it unnecessary to
specify the various CoAP message types, the Type field can be elided.
For some connection-oriented transports, such as WebSockets, the
version of CoAP being used can be negotiated during the opening
transfer. Consequently, the Version field in CoAP packets can also
be elided.
Property 5: Message encoding.
While parts of the CoAP payload are human readable or are transmitted
in XML, JSON or SenML format, CoAP is essentially a low overhead
binary protocol. Efficient transmission of such packets would
therefore be met with a transport offering binary encoding support,
although techniques exist in allowing binary payloads to be
transferred over text-based transport protocols such as base-64
encoding. A fuller discussion about performing CoAP message encoding
for SMS can be found in Appendix A.5 of [I-D.bormann-coap-misc]
Property 6: Network byte order.
Silverajan & Savolainen Expires June 20, 2015 [Page 10]
Internet-Draft CoAP Alternative Transports December 2014
CoAP, as well as transports based on the IP stack use a Big Endian
byte order for transmitting packets over the air or wire, while
transports based on Bluetooth and Zigbee prefer Little Endian byte
ordering for packet fields and transmission. Any CoAP implementation
that potentially uses multiple transports has to ensure correct byte
ordering for the transport used.
Property 7: MTU correlation with CoAP PDU size.
Section 4.6 of [RFC7252] discusses the avoidance of IP fragmentation
by ensuring CoAP message fit into a single UDP datagram. End-points
on constrained networks using 6LoWPAN may use blockwise transfers to
accommodate even smaller packet sizes to avoid fragmentation. The
MTU sizes for Bluetooth Low Energy as well as Classic Bluetooth are
provided in Section 2.4 of [I-D.ietf-6lo-btle]. Transport MTU
correlation with CoAP messages helps ensure minimal to no
fragmentation at the transport layer. On the other hand, allowing a
CoAP message to be delivered using a delay-tolerant transport service
such as the Bundle Protocol [RFC5050] would imply that the CoAP
message may be fragmented (or reconstituted) along various nodes in
the DTN as various sized bundles and bundle fragments.
Property 8: Framing
When using CoAP over a streaming transport protocol such as TCP, as
opposed to datagram based protocols, care must be observed in
preserving message boundaries. Commonly applied techniques at the
transport level include the use of delimiting characters for this
purpose as well as message framing and length prefixing.
Property 9: Transport latency.
A confirmable CoAP request would be retransmitted by a CoAP end-point
if a response is not obtained within a certain time. A CoAP end-
point registering to a Resource Directory uses a POST message that
could include a lifetime value. A sleepy end-point similarly uses a
lifetime value to indicate the freshness of the data to a CoAP Mirror
Server. Care needs to be exercised to ensure the latency of the
transport being used to carry CoAP messages is small enough not to
interfere with these values for the proper operation of these
functionalities.
Property 10: Connection Management.
A CoAP endpoint using a connection-oriented transport should be
responsible for proper connection establishment prior to sending a
CoAP Request message. Both communicating endpoints may monitor the
connection health during the Data Transfer phase. Finally, once data
Silverajan & Savolainen Expires June 20, 2015 [Page 11]
Internet-Draft CoAP Alternative Transports December 2014
transfer is complete, at least one end point should perform
connection teardown gracefully.
6. IANA Considerations
This memo includes no request to IANA.
7. Security Considerations
While no new security risks are envisaged simply from the
introduction of support for alternative transports, end-applications
and CoAP implementations should take note if certain transports
require privacy trade-offs that may arise if identifiers such as MAC
addresses or phone numbers are made public in addition to FQDNs.
8. Acknowledgements
Feedback, ideas and ongoing discussions with Klaus Hartke, Martin
Thomson, Mark Nottingham, Dave Thaler, Graham Klyne, Carsten Bormann,
Markus Becker and Golnaz Karbaschi provided useful insights and ideas
for this work.
9. References
9.1. Normative References
[I-D.ietf-appsawg-uri-scheme-reg]
Thaler, D., Hansen, T., Hardie, T., and L. Masinter,
"Guidelines and Registration Procedures for URI Schemes",
draft-ietf-appsawg-uri-scheme-reg-04 (work in progress),
October 2014.
[RFC3986] Berners-Lee, T., Fielding, R., and L. Masinter, "Uniform
Resource Identifier (URI): Generic Syntax", STD 66, RFC
3986, January 2005.
[RFC7228] Bormann, C., Ersue, M., and A. Keranen, "Terminology for
Constrained-Node Networks", RFC 7228, May 2014.
[RFC7252] Shelby, Z., Hartke, K., and C. Bormann, "The Constrained
Application Protocol (CoAP)", RFC 7252, June 2014.
9.2. Informative References
[BTCorev4.1]
BLUETOOTH Special Interest Group, "BLUETOOTH Specification
Version 4.1", December 2013.
Silverajan & Savolainen Expires June 20, 2015 [Page 12]
Internet-Draft CoAP Alternative Transports December 2014
[I-D.becker-core-coap-sms-gprs]
Becker, M., Li, K., Kuladinithi, K., and T. Poetsch,
"Transport of CoAP over SMS", draft-becker-core-coap-sms-
gprs-05 (work in progress), August 2014.
[I-D.bormann-coap-misc]
Bormann, C. and K. Hartke, "Miscellaneous additions to
CoAP", draft-bormann-coap-misc-27 (work in progress),
November 2014.
[I-D.bormann-core-coap-tcp]
Bormann, C., "A TCP transport for CoAP", draft-bormann-
core-coap-tcp-01 (work in progress), July 2014.
[I-D.fossati-dtls-over-gsm-sms]
Fossati, T. and H. Tschofenig, "Datagram Transport Layer
Security (DTLS) over Global System for Mobile
Communications (GSM) Short Message Service (SMS)", draft-
fossati-dtls-over-gsm-sms-01 (work in progress), October
2014.
[I-D.ietf-6lo-btle]
Nieminen, J., Savolainen, T., Isomaki, M., Patil, B.,
Shelby, Z., and C. Gomez, "Transmission of IPv6 Packets
over BLUETOOTH(R) Low Energy", draft-ietf-6lo-btle-03
(work in progress), September 2014.
[I-D.ietf-core-observe]
Hartke, K., "Observing Resources in CoAP", draft-ietf-
core-observe-15 (work in progress), October 2014.
[I-D.jimenez-p2psip-coap-reload]
Jimenez, J., Lopez-Vega, J., Maenpaa, J., and G.
Camarillo, "A Constrained Application Protocol (CoAP)
Usage for REsource LOcation And Discovery (RELOAD)",
draft-jimenez-p2psip-coap-reload-04 (work in progress),
July 2014.
[I-D.savolainen-core-coap-websockets]
Savolainen, T., Hartke, K., and B. Silverajan, "CoAP over
WebSockets", draft-savolainen-core-coap-websockets-03
(work in progress), October 2014.
[I-D.tschofenig-core-coap-tcp-tls]
Lemay, S., Technologies, Z., and H. Tschofenig, "A TCP and
TLS Transport for the Constrained Application Protocol
(CoAP)", draft-tschofenig-core-coap-tcp-tls-01 (work in
progress), September 2014.
Silverajan & Savolainen Expires June 20, 2015 [Page 13]
Internet-Draft CoAP Alternative Transports December 2014
[I-D.vial-core-mirror-server]
Vial, M., "CoRE Mirror Server", draft-vial-core-mirror-
server-01 (work in progress), April 2013.
[OMALWM2M]
Open Mobile Alliance (OMA), "Lightweight Machine to
Machine Technical Specification", 2013.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2609] Guttman, E., Perkins, C., and J. Kempf, "Service Templates
and Service: Schemes", RFC 2609, June 1999.
[RFC2818] Rescorla, E., "HTTP Over TLS", RFC 2818, May 2000.
[RFC4838] Cerf, V., Burleigh, S., Hooke, A., Torgerson, L., Durst,
R., Scott, K., Fall, K., and H. Weiss, "Delay-Tolerant
Networking Architecture", RFC 4838, April 2007.
[RFC5050] Scott, K. and S. Burleigh, "Bundle Protocol
Specification", RFC 5050, November 2007.
[RFC5092] Melnikov, A. and C. Newman, "IMAP URL Scheme", RFC 5092,
November 2007.
[RFC6455] Fette, I. and A. Melnikov, "The WebSocket Protocol", RFC
6455, December 2011.
[RFC6568] Kim, E., Kaspar, D., and JP. Vasseur, "Design and
Application Spaces for IPv6 over Low-Power Wireless
Personal Area Networks (6LoWPANs)", RFC 6568, April 2012.
[RFC6733] Fajardo, V., Arkko, J., Loughney, J., and G. Zorn,
"Diameter Base Protocol", RFC 6733, October 2012.
[RFC7390] Rahman, A. and E. Dijk, "Group Communication for the
Constrained Application Protocol (CoAP)", RFC 7390,
October 2014.
[WWWArchv1]
http://www.w3.org/TR/webarch/#uri-aliases, "Architecture
of the World Wide Web, Volume One", December 2004.
Silverajan & Savolainen Expires June 20, 2015 [Page 14]
Internet-Draft CoAP Alternative Transports December 2014
Appendix A. Expressing transport in the URI in other ways
Other means of indicating the transport as a distinguishable
component within the CoAP URI are possible, but have been deemed
unsuitable by not meeting the design considerations listed, or are
incompatible with existing practices outlined in [RFC7252]. They are
however, retained in this section for historical documentation and
completeness.
A.1. Transport information as part of the URI authority
A single URI scheme, "coap-at" can be introduced, as part of an
absolute URI which expresses the transport information within the
authority component. One approach is to structure the component with
a transport prefix to the endpoint identifier and a delimiter, such
as "<transport-name>-endpoint_identifier".
Examples of resulting URIs are:
o coap-at://tcp-server.example.com/sensors/temperature
o coap-at://sms-0015105550101/sensors/temperature
An implementation note here is that some generic URI parsers will
fail when encountering a URI such as "coap-at://tcp-
[2001:db8::1]/sensors/temperature". Consequently, an equivalent, but
parseable URI from the ip6.arpa domain needs to be formulated
instead. For [2001:db8::1] using TCP, this would result in the
following URL:
coap-at://tcp-1.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.8.b.d.0
.1.0.0.2.ip6.arpa:5683/sensors/temperature
Usage of an IPv4-mapped IPv6 address such as [::ffff.192.100.0.1] can
similarly be expressed with a URI from the ip6.arpa domain.
This URI format allows the usage of a single scheme to represent
multiple types of transport end-points. Consequently, it requires
consistency in ensuring how various transport-specific endpoints are
identified, as a single URI format is used. Attention must be paid
towards the syntax rules and encoding for the URI host component.
Additionally, against a base URI of the form "coap-at://tcp-
server.example.com/sensors/temperature", resolving a relative
reference, such as "//example.net/sensors/temperature" would result
in the target URI "coap-at://example.net/sensors/temperature", in
which transport information is lost.
Silverajan & Savolainen Expires June 20, 2015 [Page 15]
Internet-Draft CoAP Alternative Transports December 2014
A.1.1. Usage of DNS records
DNS names can be used instead of IPv6 address literals to mitigate
lengthy URLs referring to the ip6.arpa domain, if usage of DNS is
possible.
DNS SRV records can also be employed to formulate a URL such as:
coap-at://srv-_coap._tcp.example.com/sensors/temperature
in which the "srv" prefix is used to indicate that a DNS SRV lookup
should be used for _coap._tcp.example.com, where usage of CoAP over
TCP is specified for example.com, and is eventually resolved to a
numerical IPv4 or IPv6 address.
A.2. Making CoAP Resources Available over Multiple Transports
The CoAP URI used thus far is as follows:
URI = scheme ":" hier-part [ "?" query ]
hier-part = "//" authority path-abempty
A new URI format could be introduced, that does not possess an
"authority" component, and instead defining "hier-part" to instead
use another component, "path-rootless", as specified by RFC3986
[RFC3986]. The partial ABNF format of this URI would then be:
URI = scheme ":" hier-part [ "?" query ]
hier-part = path-rootless
path-rootless = segment-nz *( "/" segment )
The full syntax of "path-rootless" is described in [RFC3986]. A
generic URI defined this way would conform to the syntax of
[RFC3986], while the path component can be treated as an opaque
string to indicate transport types, endpoints as well as paths to
CoAP resources. A single scheme can similarly be used.
A constrained node that is capable of communicating over several
types of transports (such as UDP, TCP and SMS) would be able to
convey a single CoAP resource over multiple transports. This is also
beneficial for nodes performing caching and proxying from one type of
transport to another.
Silverajan & Savolainen Expires June 20, 2015 [Page 16]
Internet-Draft CoAP Alternative Transports December 2014
Requesting and retrieving the same CoAP resource representation over
multiple transports could be rendered possible by prefixing the
transport type and endpoint identifier information to the CoAP URI.
This would result in the following example representation:
coap-at:tcp://example.com?coap://example.com/sensors/temperature
\_______ ______/ \________________ __________________/
\/ \/
Transport-specific CoAP Resource
Prefix
Figure 2: Prefixing a CoAP URI with TCP transport
Such a representation would result in the URI being decomposed into
its constituent components, with the CoAP resource residing within
the query component as follows:
Scheme: coap-at
Path: tcp://example.com
Query: coap://example.com/sensors/temperature
The same CoAP resource, if requested over a WebSocket transport,
would result the following URI:
coap-at:ws://example.com/endpoint?coap://example.com/sensors/temperature
\___________ __________/ \_______________ ___________________/
\/ \/
Transport-specific CoAP Resource
Prefix
Figure 3: Prefixing a CoAP URI with WebSocket transport
While the transport prefix changes, the CoAP resource representation
remains the same in the query component:
Scheme: coap-at
Path: ws://example.com/endpoint
Silverajan & Savolainen Expires June 20, 2015 [Page 17]
Internet-Draft CoAP Alternative Transports December 2014
Query: coap://example.com/sensors/temperature
The URI format described here overcomes URI aliasing [WWWArchv1] when
multiple transports are used, by ensuring each CoAP resource
representation remains the same, but is prefixed with different
transports. However, against a base URI of this format, resolving
relative references of the form "//example.net/sensors/temperature"
and "/sensor2/temperature" would again result in target URIs which
lose transport-specific information.
Implementation note: While square brackets are disallowed within the
path component, the '[' and ']' characters needed to enclose a
literal IPv6 address can be percent-encoded into their respective
equivalents. The ':' character does not need to be percent-encoded.
This results in a significantly simpler URI string compared to
section 2.2, particularly for compressed IPv6 addresses.
Additionally, the URI format can be used to specify other similar
address families and formats, such as Bluetooth addresses
[BTCorev4.1].
A.3. Transport as part of a 'service:' URL scheme
The "service:" URL scheme name was introduced in [RFC2609] and forms
the basis of service description used primarily by the Service
Location Protocol. An abstract service type URI would have the form
"service:<abstract-type>:<concrete-type>"
where <abstract-type> refers to a service type name that can be
associated with a variety of protocols, while the <concrete-type>
then providing the specific details of the protocol used, authority
and other URI components.
Adopting the "service:" URL scheme to describe CoAP usage over
alternative transports would be rather trivial. To use a previous
example, a CoAP service to discover a Resource Directory and its base
RD resource using TCP would take the form
service:coap:tcp://host.example.com/.well-known/core?rt=core-rd
The syntax of the "service:" URL scheme differs from the generic URI
syntax and therefore such a representation should be treated as an
opaque URI as Section 2.1 of [RFC2609] recommends.
Silverajan & Savolainen Expires June 20, 2015 [Page 18]
Internet-Draft CoAP Alternative Transports December 2014
Authors' Addresses
Bilhanan Silverajan
Tampere University of Technology
Korkeakoulunkatu 10
FI-33720 Tampere
Finland
Email: bilhanan.silverajan@tut.fi
Teemu Savolainen
Nokia
Hermiankatu 12 D
FI-33720 Tampere
Finland
Email: teemu.savolainen@nokia.com
Silverajan & Savolainen Expires June 20, 2015 [Page 19]