Network Working Group F. Templin, Ed.
Internet-Draft Boeing Research & Technology
Obsoletes: rfc5320, rfc5558, rfc5720, February 10, 2015
rfc6179, rfc6706 (if
approved)
Intended status: Standards Track
Expires: August 14, 2015
Transmission of IP Packets over AERO Links
draft-templin-aerolink-52.txt
Abstract
This document specifies the operation of IP over tunnel virtual links
using Asymmetric Extended Route Optimization (AERO). Nodes attached
to AERO links can exchange packets via trusted intermediate routers
that provide forwarding services to reach off-link destinations and
redirection services for route optimization. AERO provides an IPv6
link-local address format known as the AERO address that supports
operation of the IPv6 Neighbor Discovery (ND) protocol and links IPv6
ND to IP forwarding. Admission control and provisioning are
supported by the Dynamic Host Configuration Protocol for IPv6
(DHCPv6), and node mobility is naturally supported through dynamic
neighbor cache updates. Although DHCPv6 and IPv6 ND messaging is
used in the control plane, both IPv4 and IPv6 are supported in the
data plane.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on August 14, 2015.
Templin Expires August 14, 2015 [Page 1]
Internet-Draft AERO February 2015
Copyright Notice
Copyright (c) 2015 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 4
3. Asymmetric Extended Route Optimization (AERO) . . . . . . . . 6
3.1. AERO Link Reference Model . . . . . . . . . . . . . . . . 6
3.2. AERO Link Node Types . . . . . . . . . . . . . . . . . . 8
3.3. AERO Addresses . . . . . . . . . . . . . . . . . . . . . 9
3.4. AERO Interface Characteristics . . . . . . . . . . . . . 10
3.5. AERO Link Registration . . . . . . . . . . . . . . . . . 11
3.6. AERO Interface Initialization . . . . . . . . . . . . . . 12
3.6.1. AERO Relay Behavior . . . . . . . . . . . . . . . . . 12
3.6.2. AERO Server Behavior . . . . . . . . . . . . . . . . 12
3.6.3. AERO Client Behavior . . . . . . . . . . . . . . . . 12
3.6.4. AERO Forwarding Agent Behavior . . . . . . . . . . . 13
3.7. AERO Link Routing System . . . . . . . . . . . . . . . . 13
3.8. AERO Interface Neighbor Cache Maintenace . . . . . . . . 14
3.9. AERO Interface Sending Algorithm . . . . . . . . . . . . 16
3.10. AERO Interface Encapsulation and Re-encapsulation . . . . 17
3.11. AERO Interface Decapsulation . . . . . . . . . . . . . . 20
3.12. AERO Interface Data Origin Authentication . . . . . . . . 20
3.13. AERO Interface MTU and Fragmentation . . . . . . . . . . 21
3.13.1. Accommodating Large Control Messages . . . . . . . . 23
3.13.2. Integrity . . . . . . . . . . . . . . . . . . . . . 24
3.14. AERO Interface Error Handling . . . . . . . . . . . . . . 25
3.15. AERO Router Discovery, Prefix Delegation and Address
Configuration . . . . . . . . . . . . . . . . . . . . . . 29
3.15.1. AERO DHCPv6 Service Model . . . . . . . . . . . . . 29
3.15.2. AERO Client Behavior . . . . . . . . . . . . . . . . 30
3.15.3. AERO Server Behavior . . . . . . . . . . . . . . . . 32
3.16. AERO Forwarding Agent Discovery . . . . . . . . . . . . . 36
3.17. AERO Intradomain Route Optimization . . . . . . . . . . . 36
3.17.1. Reference Operational Scenario . . . . . . . . . . . 37
Templin Expires August 14, 2015 [Page 2]
Internet-Draft AERO February 2015
3.17.2. Concept of Operations . . . . . . . . . . . . . . . 38
3.17.3. Message Format . . . . . . . . . . . . . . . . . . . 38
3.17.4. Sending Predirects . . . . . . . . . . . . . . . . . 39
3.17.5. Re-encapsulating and Relaying Predirects . . . . . . 41
3.17.6. Processing Predirects and Sending Redirects . . . . 41
3.17.7. Re-encapsulating and Relaying Redirects . . . . . . 43
3.17.8. Processing Redirects . . . . . . . . . . . . . . . . 44
3.17.9. Server-Oriented Redirection . . . . . . . . . . . . 44
3.18. Neighbor Unreachability Detection (NUD) . . . . . . . . . 45
3.19. Mobility Management . . . . . . . . . . . . . . . . . . . 46
3.19.1. Announcing Link-Layer Address Changes . . . . . . . 46
3.19.2. Bringing New Links Into Service . . . . . . . . . . 47
3.19.3. Removing Existing Links from Service . . . . . . . . 48
3.19.4. Moving to a New Server . . . . . . . . . . . . . . . 48
3.20. Proxy AERO . . . . . . . . . . . . . . . . . . . . . . . 49
3.21. Extending AERO Links Through Security Gateways . . . . . 51
3.22. Extending IPv6 AERO Links to the Internet . . . . . . . . 53
3.23. Encapsulation Protocol Version Considerations . . . . . . 56
3.24. Multicast Considerations . . . . . . . . . . . . . . . . 57
3.25. Operation on AERO Links Without DHCPv6 Services . . . . . 57
3.26. Operation on Server-less AERO Links . . . . . . . . . . . 57
3.27. Manually-Configured AERO Tunnels . . . . . . . . . . . . 57
3.28. Intradomain Routing . . . . . . . . . . . . . . . . . . . 58
4. Implementation Status . . . . . . . . . . . . . . . . . . . . 58
5. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 58
6. Security Considerations . . . . . . . . . . . . . . . . . . . 58
7. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 59
8. References . . . . . . . . . . . . . . . . . . . . . . . . . 60
8.1. Normative References . . . . . . . . . . . . . . . . . . 60
8.2. Informative References . . . . . . . . . . . . . . . . . 61
Author's Address . . . . . . . . . . . . . . . . . . . . . . . . 65
1. Introduction
This document specifies the operation of IP over tunnel virtual links
using Asymmetric Extended Route Optimization (AERO). The AERO link
can be used for tunneling to neighboring nodes over either IPv6 or
IPv4 networks, i.e., AERO views the IPv6 and IPv4 networks as
equivalent links for tunneling. Nodes attached to AERO links can
exchange packets via trusted intermediate routers that provide
forwarding services to reach off-link destinations and redirection
services for route optimization that addresses the requirements
outlined in [RFC5522].
AERO provides an IPv6 link-local address format known as the AERO
address that supports operation of the IPv6 Neighbor Discovery (ND)
[RFC4861] protocol and links IPv6 ND to IP forwarding. Admission
control and provisioning are supported by the Dynamic Host
Templin Expires August 14, 2015 [Page 3]
Internet-Draft AERO February 2015
Configuration Protocol for IPv6 (DHCPv6) [RFC3315], and node mobility
is naturally supported through dynamic neighbor cache updates.
Although DHCPv6 and IPv6 ND messaging is used in the control plane,
both IPv4 and IPv6 can be used in the data plane. The remainder of
this document presents the AERO specification.
2. Terminology
The terminology in the normative references applies; the following
terms are defined within the scope of this document:
AERO link
a Non-Broadcast, Multiple Access (NBMA) tunnel virtual overlay
configured over a node's attached IPv6 and/or IPv4 networks. All
nodes on the AERO link appear as single-hop neighbors from the
perspective of the virtual overlay.
AERO interface
a node's attachment to an AERO link. Nodes typically have a
single AERO interface; support for multiple AERO interfaces is
also possible but out of scope for this document.
AERO address
an IPv6 link-local address constructed as specified in Section 3.3
and assigned to a Client's AERO interface.
AERO node
a node that is connected to an AERO link and that participates in
IPv6 ND and DHCPv6 messaging over the link.
AERO Client ("Client")
a node that issues DHCPv6 messages using the special IPv6 link-
local address 'fe80::ffff:ffff:ffff:ffff' to receive IP Prefix
Delegations (PD) from one or more AERO Servers. Following PD, the
Client assigns an AERO address to the AERO interface then
coordinates with other AERO nodes using IPv6 ND messaging.
AERO Server ("Server")
a node that configures an AERO interface to provide default
forwarding and DHCPv6 services for AERO Clients. The Server
assigns an administratively assigned IPv6 link-local unicast
address to support the operation of DHCPv6 and the IPv6 ND
protocol.
AERO Relay ("Relay")
a node that configures an AERO interface to relay IP packets
between nodes on the same AERO link and/or forward IP packets
between the AERO link and the native Internetwork. The Relay
Templin Expires August 14, 2015 [Page 4]
Internet-Draft AERO February 2015
assigns an administratively assigned IPv6 link-local unicast
address to the AERO interface the same as for a Server.
AERO Forwarding Agent ("Forwarding Agent")
a node that performs data plane forwarding services as a companion
to other AERO nodes.
ingress tunnel endpoint (ITE)
an AERO interface endpoint that injects tunneled packets into an
AERO link.
egress tunnel endpoint (ETE)
an AERO interface endpoint that receives tunneled packets from an
AERO link.
underlying network
a connected IPv6 or IPv4 network routing region over which the
tunnel virtual overlay is configured. A typical example is an
enterprise network.
underlying interface
an AERO node's interface point of attachment to an underlying
network.
link-layer address
an IP address assigned to an AERO node's underlying interface.
When UDP encapsulation is used, the UDP port number is also
considered as part of the link-layer address. Link-layer
addresses are used as the encapsulation header source and
destination addresses.
network layer address
the source or destination address of the encapsulated IP packet.
end user network (EUN)
an internal virtual or external edge IP network that an AERO
Client connects to the rest of the network via the AERO interface.
AERO Service Prefix (ASP)
an IP prefix associated with the AERO link and from which AERO
Client Prefixes (ACPs) are derived (for example, the IPv6 ACP
2001:db8:1:2::/64 is derived from the IPv6 ASP 2001:db8::/32).
AERO Client Prefix (ACP)
a more-specific IP prefix taken from an ASP and delegated to a
Client.
Templin Expires August 14, 2015 [Page 5]
Internet-Draft AERO February 2015
Throughout the document, the simple terms "Client", "Server" and
"Relay" refer to "AERO Client", "AERO Server" and "AERO Relay",
respectively. Capitalization is used to distinguish these terms from
DHCPv6 client/server/relay [RFC3315].
The terminology of [RFC4861] (including the names of node variables
and protocol constants) applies to this document. Also throughout
the document, the term "IP" is used to generically refer to either
Internet Protocol version (i.e., IPv4 or IPv6).
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
3. Asymmetric Extended Route Optimization (AERO)
The following sections specify the operation of IP over Asymmetric
Extended Route Optimization (AERO) links:
3.1. AERO Link Reference Model
Templin Expires August 14, 2015 [Page 6]
Internet-Draft AERO February 2015
.-(::::::::)
.-(:::: IP ::::)-.
(:: Internetwork ::)
`-(::::::::::::)-'
`-(::::::)-'
|
+--------------+ +--------+-------+ +--------------+
|AERO Server S1| | AERO Relay R1 | |AERO Server S2|
| Nbr: C1; R1 | | Nbr: S1; S2 | | Nbr: C2; R1 |
| default->R1 | |(H1->S1; H2->S2)| | default->R1 |
| H1->C1 | +--------+-------+ | H2->C2 |
+-------+------+ | +------+-------+
| | |
X---+---+-------------------+------------------+---+---X
| AERO Link |
+-----+--------+ +--------+-----+
|AERO Client C1| |AERO Client C2|
| Nbr: S1 | | Nbr: S2 |
| default->S1 | | default->S2 |
+--------------+ +--------------+
.-. .-.
,-( _)-. ,-( _)-.
.-(_ IP )-. .-(_ IP )-.
(__ EUN ) (__ EUN )
`-(______)-' `-(______)-'
| |
+--------+ +--------+
| Host H1| | Host H2|
+--------+ +--------+
Figure 1: AERO Link Reference Model
Figure 1 presents the AERO link reference model. In this model:
o Relay R1 acts as a default router for its associated Servers S1
and S2, and connects the AERO link to the rest of the IP
Internetwork
o Servers S1 and S2 associate with Relay R1 and also act as default
routers for their associated Clients C1 and C2.
o Clients C1 and C2 associate with Servers S1 and S2, respectively
and also act as default routers for their associated EUNs
o Hosts H1 and H2 attach to the EUNs served by Clients C1 and C2,
respectively
Templin Expires August 14, 2015 [Page 7]
Internet-Draft AERO February 2015
Each node maintains a neighbor cache and IP forwarding table. (For
example, AERO Relay R1 in the diagram has neighbor cache entries for
Servers S1 and S2 and IP forwarding table entries for ACPs H1 and
H2.) In common operational practice, there may be many additional
Relays, Servers and Clients. (Although not shown in the figure, AERO
Forwarding Agents may also be provided for data plane forwarding
offload services.)
3.2. AERO Link Node Types
AERO Relays provide default forwarding services to AERO Servers.
Relays forward packets between Servers connected to the same AERO
link and also forward packets between the AERO link and the native IP
Internetwork. Relays present the AERO link to the native
Internetwork as a set of one or more AERO Service Prefixes (ASPs) and
serve as a gateway between the AERO link and the Internetwork. AERO
Relays maintain an AERO interface neighbor cache entry for each AERO
Server, and maintain an IP forwarding table entry for each AERO
Client Prefix (ACP).
AERO Servers provide default forwarding services to AERO Clients.
Each Server also peers with each Relay in a dynamic routing protocol
instance to advertise its list of associated ACPs. Servers configure
a DHCPv6 server function to facilitate Prefix Delegation (PD)
exchanges with Clients. Each delegated prefix becomes an ACP taken
from an ASP. Servers forward packets between AERO interface
neighbors only, i.e., and not between the AERO link and the native IP
Internetwork unless they are also configured as a Relay. AERO
Servers maintain an AERO interface neighbor cache entry for each AERO
Relay. They also maintain both a neighbor cache entry and an IP
forwarding table entry for each of their associated Clients.
AERO Clients act as requesting routers to receive ACPs through DHCPv6
PD exchanges with AERO Servers over the AERO link and sub-delegate
portions of their ACPs to EUN interfaces. (Each Client MAY associate
with a single Server or with multiple Servers, e.g., for fault
tolerance, load balancing, etc.) Each IPv6 Client receives at least
a /64 IPv6 ACP, and may receive even shorter prefixes. Similarly,
each IPv4 Client receives at least a /32 IPv4 ACP (i.e., a singleton
IPv4 address), and may receive even shorter prefixes. AERO Clients
maintain an AERO interface neighbor cache entry for each of their
associated Servers as well as for each of their correspondent
Clients.
AERO Clients typically configure a TUN/TAP interface [TUNTAP] as a
point-to-point linkage between the IP layer and the AERO interface.
The IP layer therefore sees only the TUN/TAP interface, while the
AERO interface provides an intermediate conduit between the TUN/TAP
Templin Expires August 14, 2015 [Page 8]
Internet-Draft AERO February 2015
interface and the underlying interfaces. AERO Clients that act as
hosts assign one or more IP addresses from their ACPs to the TUN/TAP
interface, i.e., and not to the AERO interface.
AERO Forwarding Agents provide data plane forwarding services as
companions to other AERO nodes. Note that while all Relays, Servers
and Clients are required to perform both control and data plane
operations on their own behalf, they may optionally enlist the
services of special-purpose Forwarding Agents to offload performance-
intensive traffic.
3.3. AERO Addresses
An AERO address is an IPv6 link-local address with an embedded ACP
and assigned to a Client's AERO interface. The AERO address is
formed as follows:
fe80::[ACP]
For IPv6, the AERO address begins with the prefix fe80::/64 and
includes in its interface identifier the base prefix taken from the
Client's IPv6 ACP. The base prefix is determined by masking the ACP
with the prefix length. For example, if the AERO Client receives the
IPv6 ACP:
2001:db8:1000:2000::/56
it constructs its AERO address as:
fe80::2001:db8:1000:2000
For IPv4, the AERO address is formed from the lower 64 bits of an
IPv4-mapped IPv6 address [RFC4291] that includes the base prefix
taken from the Client's IPv4 ACP. For example, if the AERO Client
receives the IPv4 ACP:
192.0.2.32/28
it constructs its AERO address as:
fe80::FFFF:192.0.2.32
The AERO address remains stable as the Client moves between
topological locations, i.e., even if its link-layer addresses change.
NOTE: In some cases, prospective neighbors may not have advanced
knowledge of the Client's ACP length and may therefore send initial
IPv6 ND messages with an AERO destination address that matches the
Templin Expires August 14, 2015 [Page 9]
Internet-Draft AERO February 2015
ACP but does not correspond to the base prefix. In that case, the
Client MUST accept the address as equivalent to the base address, but
then use the base address as the source address of any IPv6 ND
message replies. For example, if the Client receives the IPv6 ACP
2001:db8:1000:2000::/56 then subsequently receives an IPv6 ND message
with destination address fe80::2001:db8:1000:2001, it accepts the
message but uses fe80::2001:db8:1000:2000 as the source address of
any IPv6 ND replies.
3.4. AERO Interface Characteristics
AERO interfaces use encapsulation (see Section 3.10) to exchange
packets with neighbors attached to the AERO link. AERO interfaces
maintain a neighbor cache, and AERO Clients and Servers use unicast
IPv6 ND messaging. AERO interfaces use unicast Neighbor Solicitation
(NS), Neighbor Advertisement (NA), Router Solicitation (RS) and
Router Advertisement (RA) messages the same as for any IPv6 link.
AERO interfaces use two redirection message types -- the first known
as a Predirect message and the second being the standard Redirect
message (see Section 3.17). AERO links further use link-local-only
addressing; hence, AERO nodes ignore any Prefix Information Options
(PIOs) they may receive in RA messages over an AERO interface.
AERO interface ND messages include one or more Source/Target Link-
Layer Address Options (S/TLLAOs) formatted as shown in Figure 2:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = 2 | Length = 3 | Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Link ID | Preference | UDP Port Number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ +
| |
+ IP Address +
| |
+ +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 2: AERO Source/Target Link-Layer Address Option (S/TLLAO)
Format
In this format, Link ID is an integer value between 0 and 255
corresponding to an underlying interface of the target node, and
Preference is an integer value between 0 and 255 indicating the
Templin Expires August 14, 2015 [Page 10]
Internet-Draft AERO February 2015
node's preference for this underlying interface (with 255 being the
highest preference, 1 being the lowest, and 0 meaning "link
disabled"). UDP Port Number and IP Address are set to the addresses
used by the target node when it sends encapsulated packets over the
underlying interface. When the encapsulation IP address family is
IPv4, IP Address is formed as an IPv4-mapped IPv6 address [RFC4291].
AERO interfaces may be configured over multiple underlying
interfaces. For example, common mobile handheld devices have both
wireless local area network ("WLAN") and cellular wireless links.
These links are typically used "one at a time" with low-cost WLAN
preferred and highly-available cellular wireless as a standby. In a
more complex example, aircraft frequently have many wireless data
link types (e.g. satellite-based, terrestrial, air-to-air
directional, etc.) with diverse performance and cost properties.
If a Client's multiple underlying interfaces are used "one at a time"
(i.e., all other interfaces are in standby mode while one interface
is active), then Redirect, Predirect and unsolicited NA messages
include only a single TLLAO with Link ID set to a constant value.
If the Client has multiple active underlying interfaces, then from
the perspective of IPv6 ND it would appear to have a single link-
local address with multiple link-layer addresses. In that case,
Redirect, Predirect and unsolicited NA messages MAY include multiple
TLLAOs -- each with a different Link ID that corresponds to a
specific underlying interface of the Client.
3.5. AERO Link Registration
When an administrative authority first deploys a set of AERO Relays
and Servers that comprise an AERO link, they also assign a unique
domain name for the link, e.g., "example.com". Next, if
administrative policy permits Clients within the domain to serve as
correspondent nodes for Internet mobile nodes, the administrative
authority adds a Fully Qualified Domain Name (FQDN) for each of the
AERO link's ASPs to the Domain Name System (DNS) [RFC1035]. The FQDN
is based on the suffix "aero.linkupnetworks.net" with a wildcard-
terminated reverse mapping of the ASP [RFC3596][RFC4592], and
resolves to a DNS PTR resource record. For example, for the ASP
'2001:db8:1::/48' within the domain name "example.com", the DNS
database contains:
'*.1.0.0.0.8.b.d.0.1.0.0.2.aero.linkupnetworks.net. PTR example.com'
This DNS registration advertises the AERO link's ASPs to prospective
mobile nodes.
Templin Expires August 14, 2015 [Page 11]
Internet-Draft AERO February 2015
3.6. AERO Interface Initialization
3.6.1. AERO Relay Behavior
When a Relay enables an AERO interface, it first assigns an
administratively-assigned link-local address fe80::ID to the
interface. Each fe80::ID address MUST be unique among all AERO nodes
on the link, and MUST NOT collide with any potential AERO addresses
nor the special addresses fe80:: and fe80::ffff:ffff:ffff:ffff. (The
fe80::ID addresses are typically taken from the available range
fe80::/96, e.g., as fe80::1, fe80::2, fe80::3, etc.) The Relay then
engages in a dynamic routing protocol session with all Servers on the
link (see: Section 3.7), and advertises the set of ASPs into the
native IP Internetwork.
Each Relay subsequently maintains an IP forwarding table entry for
each Client-Server association, and maintains a neighbor cache entry
for each Server on the link. Relays exchange NS/NA messages with
AERO link neighbors the same as for any AERO node, however they
typically do not perform explicit Neighbor Unreachability Detection
(NUD) (see: Section 3.18) since the dynamic routing protocol already
provides reachability confirmation.
3.6.2. AERO Server Behavior
When a Server enables an AERO interface, it assigns an
administratively assigned link-local address fe80::ID the same as for
Relays. The Server further configures a DHCPv6 server function to
facilitate DHCPv6 PD exchanges with AERO Clients. The Server
maintains a neighbor cache entry for each Relay on the link, and
manages per-Client neighbor cache entries and IP forwarding table
entries based on control message exchanges. Each Server also engages
in a dynamic routing protocol with each Relay on the link (see:
Section 3.7).
When the Server receives an NS/RS message on the AERO interface it
returns an NA/RA message but does not update the neighbor cache. The
Server further provides a simple conduit between AERO interface
neighbors. Therefore, packets enter the Server's AERO interface from
the link layer and are forwarded back out the link layer without ever
leaving the AERO interface and therefore without ever disturbing the
network layer.
3.6.3. AERO Client Behavior
When a Client enables an AERO interface, it uses the special address
fe80::ffff:ffff:ffff:ffff to obtain an ACP from an AERO Server via
DHCPv6 PD. Next, it assigns the corresponding AERO address to the
Templin Expires August 14, 2015 [Page 12]
Internet-Draft AERO February 2015
AERO interface and creates a neighbor cache entry for the Server,
i.e., the PD exchange bootstraps autoconfiguration of a unique link-
local address. The Client maintains a neighbor cache entry for each
of its Servers and each of its active correspondent Clients. When
the Client receives Redirect/Predirect messages on the AERO interface
it updates or creates neighbor cache entries, including link-layer
address information. Unsolicited NA messages update the cached link-
layer addresses for correspondent Clients (e.g., following a link-
layer address change due to node mobility) but do not create new
neighbor cache entries. NS/NA messages used for NUD update timers in
existing neighbor cache entires but do not update link-layer
addresses nor create new neighbor cache entries.
Finally, the Client need not maintain any IP forwarding table entries
for its Servers or correspondent Clients. Instead, it can set a
single "route-to-interface" default route in the IP forwarding table,
and all forwarding decisions can be made within the AERO interface
based on neighbor cache entries. (On systems in which adding a
default route would violate security policy, the default route could
instead be installed via a "synthesized RA", e.g., as discussed in
Section 3.15.2.)
3.6.4. AERO Forwarding Agent Behavior
When a Forwarding Agent enables an AERO interface, it assigns the
same link-local address(es) as the companion AERO node that manages
AERO control messaging services. The Forwarding Agent thereafter
provides data plane forwarding services based solely on the
forwarding information assigned to it by the companion AERO node.
AERO Forwarding Agents perform NS/NA messaging, i.e., the same as for
any AERO node.
3.7. AERO Link Routing System
Relays require full topology knowledge of all ACP/Server
associations, while individual Servers at a minimum only need to know
the ACPs for their current set of associated Clients. This is
accomplished through the use of an internal instance of the Border
Gateway Protocol (BGP) [RFC4271] coordinated between Servers and
Relays. This internal BGP instance does not interact with the public
Internet BGP instance; therefore, the AERO link is presented to the
IP Internetwork as a small set of ASPs as opposed to the full set of
individual ACPs.
In a reference BGP arrangement, each AERO Server is configured as an
Autonomous System Border Router (ASBR) for a stub Autonomous System
(AS) (possibly using a private AS Number (ASN) [RFC1930]), and each
Server further peers with each Relay but does not peer with other
Templin Expires August 14, 2015 [Page 13]
Internet-Draft AERO February 2015
Servers. Similarly, Relays do not peer with each other, since they
will reliably receive all updates from all Servers and will therefore
have a consistent view of the AERO link ACP delegations.
Each Server maintains a working set of associated ACPs, and
dynamically announces new ACPs and withdraws departed ACPs in its BGP
updates to Relays. Clients are expected to remain associated with
their current Servers for extended timeframes, however Servers SHOULD
selectively suppress BGP updates for impatient Clients that
repeatedly associate and disassociate with them in order to dampen
routing churn.
In some environments, Relays need not send BGP updates to Servers
since Servers can always use Relays as default routers, however this
presents a data/control plane performance tradeoff. In environments
where sustained packet forwarding over Relays is undesirable, Relays
can instead report ACPs to Servers while including a BGP Remote-Next-
Hop [I-D.vandevelde-idr-remote-next-hop]. The Server then creates a
neighbor cache entry for each ACP with the Remote-Next-Hop as the
link-layer address to enable Server-to-Server route optimization.
3.8. AERO Interface Neighbor Cache Maintenace
Each AERO interface maintains a conceptual neighbor cache that
includes an entry for each neighbor it communicates with on the AERO
link, the same as for any IPv6 interface [RFC4861]. AERO interface
neighbor cache entires are said to be one of "permanent", "static" or
"dynamic".
Permanent neighbor cache entries are created through explicit
administrative action; they have no timeout values and remain in
place until explicitly deleted. AERO Relays maintain a permanent
neighbor cache entry for each Server on the link, and AERO Servers
maintain a permanent neighbor cache entry for each Relay. Each entry
maintains the mapping between the neighbor's fe80::ID network-layer
address and corresponding link-layer address.
Static neighbor cache entries are created though DHCPv6 PD exchanges
and remain in place for durations bounded by prefix lifetimes. AERO
Servers maintain static neighbor cache entries for the ACPs of each
of their associated Clients, and AERO Clients maintain a static
neighbor cache entry for each of their associated Servers. When an
AERO Server sends a DHCPv6 Reply message response to a Client's
DHCPv6 Solicit/Request, Rebind or Renew message, it creates or
updates a static neighbor cache entry based on the AERO address
corresponding to the Client's ACP as the network-layer address, the
prefix lifetime as the neighbor cache entry lifetime, the Client's
encapsulation IP address and UDP port number as the link-layer
Templin Expires August 14, 2015 [Page 14]
Internet-Draft AERO February 2015
address and the prefix length as the length to apply to the AERO
address. When an AERO Client receives a DHCPv6 Reply message from a
Server, it creates or updates a static neighbor cache entry based on
the Reply message link-local source address as the network-layer
address, the prefix lifetime as the neighbor cache entry lifetime,
and the encapsulation IP source address and UDP source port number as
the link-layer address.
Dynamic neighbor cache entries are created or updated based on
receipt of an IPv6 ND message, and are garbage-collected if not used
within a short timescale. AERO Clients maintain dynamic neighbor
cache entries for each of their active correspondent Client ACPs with
lifetimes based on IPv6 ND messaging constants. When an AERO Client
receives a valid Predirect message it creates or updates a dynamic
neighbor cache entry for the Predirect target network-layer and link-
layer addresses plus prefix length. The node then sets an
"AcceptTime" variable in the neighbor cache entry to ACCEPT_TIME
seconds and uses this value to determine whether packets received
from the correspondent can be accepted. When an AERO Client receives
a valid Redirect message it creates or updates a dynamic neighbor
cache entry for the Redirect target network-layer and link-layer
addresses plus prefix length. The Client then sets a "ForwardTime"
variable in the neighbor cache entry to FORWARD_TIME seconds and uses
this value to determine whether packets can be sent directly to the
correspondent. The Client also sets a "MaxRetry" variable to
MAX_RETRY to limit the number of keepalives sent when a correspondent
may have gone unreachable.
For dynamic neighbor cache entries, when an AERO Client receives a
valid NS message it (re)sets AcceptTime for the neighbor to
ACCEPT_TIME. When an AERO Client receives a valid solicited NA
message, it (re)sets ForwardTime for the neighbor to FORWARD_TIME and
sets MaxRetry to MAX_RETRY. When an AERO Client receives a valid
unsolicited NA message, it updates the correspondent's link-layer
addresses but DOES NOT reset AcceptTime, ForwardTime or MaxRetry.
It is RECOMMENDED that FORWARD_TIME be set to the default constant
value 30 seconds to match the default REACHABLE_TIME value specified
for IPv6 ND [RFC4861].
It is RECOMMENDED that ACCEPT_TIME be set to the default constant
value 40 seconds to allow a 10 second window so that the AERO
redirection procedure can converge before AcceptTime decrements below
FORWARD_TIME.
It is RECOMMENDED that MAX_RETRY be set to 3 the same as described
for IPv6 ND address resolution in Section 7.3.3 of [RFC4861].
Templin Expires August 14, 2015 [Page 15]
Internet-Draft AERO February 2015
Different values for FORWARD_TIME, ACCEPT_TIME, and MAX_RETRY MAY be
administratively set, if necessary, to better match the AERO link's
performance characteristics; however, if different values are chosen,
all nodes on the link MUST consistently configure the same values.
Most importantly, ACCEPT_TIME SHOULD be set to a value that is
sufficiently longer than FORWARD_TIME to allow the AERO redirection
procedure to converge.
3.9. AERO Interface Sending Algorithm
IP packets enter a node's AERO interface either from the network
layer (i.e., from a local application or the IP forwarding system),
or from the link layer (i.e., from the AERO tunnel virtual link).
Packets that enter the AERO interface from the network layer are
encapsulated and admitted into the AERO link, i.e., they are
tunnelled to an AERO interface neighbor. Packets that enter the AERO
interface from the link layer are either re-admitted into the AERO
link or delivered to the network layer where they are subject to
either local delivery or IP forwarding. Since each AERO node may
have only partial information about neighbors on the link, AERO
interfaces may forward packets with link-local destination addresses
at a layer below the network layer. This means that AERO nodes act
as both IP routers and sub-IP layer forwarding agents. AERO
interface sending considerations for Clients, Servers and Relays are
given below.
When an IP packet enters a Client's AERO interface from the network
layer, if the destination is covered by an ASP the Client searches
for a dynamic neighbor cache entry with a non-zero ForwardTime and an
AERO address that matches the packet's destination address. (The
destination address may be either an address covered by the
neighbor's ACP or the (link-local) AERO address itself.) If there is
a match, the Client uses a link-layer address in the entry as the
link-layer address for encapsulation then admits the packet into the
AERO link. If there is no match, the Client instead uses the link-
layer address of a neighboring Server as the link-layer address for
encapsulation.
When an IP packet enters a Server's AERO interface from the link
layer, if the destination is covered by an ASP the Server searches
for a neighbor cache entry with an AERO address that matches the
packet's destination address. (The destination address may be either
an address covered by the neighbor's ACP or the AERO address itself.)
If there is a match, the Server uses a link-layer address in the
entry as the link-layer address for encapsulation and re-admits the
packet into the AERO link. If there is no match, the Server instead
uses the link-layer address in a permanent neighbor cache entry for a
Relay as the link-layer address for encapsulation.
Templin Expires August 14, 2015 [Page 16]
Internet-Draft AERO February 2015
When an IP packet enters a Relay's AERO interface from the network
layer, the Relay searches its IP forwarding table for an entry that
is covered by an ASP and also matches the destination. If there is a
match, the Relay uses the link-layer address in a permanent neighbor
cache entry for a Server as the link-layer address for encapsulation
and admits the packet into the AERO link. When an IP packet enters a
Relay's AERO interface from the link-layer, if the destination is not
a link-local address and does not match an ASP the Relay removes the
packet from the AERO interface and uses IP forwarding to forward the
packet to the Internetwork. If the destination address is a link-
local address or a non-link-local address that matches an ASP, and
there is a more-specific ACP entry in the IP forwarding table, the
Relay uses the link-layer address in the corresponding neighbor cache
entry as the link-layer address for encapsulation and re-admits the
packet into the AERO link. When an IP packet enters a Relay's AERO
interface from either the network layer or link-layer, and the
packet's destination address matches an ASP but there is no more-
specific ACP entry, the Relay drops the packet and returns an ICMP
Destination Unreachable message (see: Section 3.14).
When an AERO Server receives a packet from a Relay via the AERO
interface, the Server MUST NOT forward the packet back to the same or
a different Relay.
When an AERO Relay receives a packet from a Server via the AERO
interface, the Relay MUST NOT forward the packet back to the same
Server.
When an AERO node re-admits a packet into the AERO link without
involving the network layer, the node MUST NOT decrement the network
layer TTL/Hop-count.
When an AERO node forwards a data packet to the primary link-layer
address of a neighbor, it may receive RA messages with one or more
SLLAOs that include the link-layer addresses of AERO Forwarding
Agents. The AERO node SHOULD record the link-layer addresses in the
neighbor cache entry for the neighbor and send subsequent data
packets via one of these addresses instead of the neighbor's primary
address (see: Section 3.16).
3.10. AERO Interface Encapsulation and Re-encapsulation
AERO interfaces encapsulate IP packets according to whether they are
entering the AERO interface from the network layer or if they are
being re-admitted into the same AERO link they arrived on. This
latter form of encapsulation is known as "re-encapsulation".
Templin Expires August 14, 2015 [Page 17]
Internet-Draft AERO February 2015
The AERO interface encapsulates packets per the base tunneling
specifications (e.g., [RFC2003], [RFC2473], [RFC2784], [RFC4213],
[RFC4301], [RFC5246], etc.) except that it inserts a UDP header
immediately following the IP encapsulation header. If there are no
additional encapsulation headers (and no fragmentation,
identification, checksum or signature is needed), the AERO interface
next encapsulates the IPv4 or IPv6 packet immediately following the
UDP header. In that case, the most significant four bits of the
encapsulated packet encode the value '4' for IPv4 or '6' for IPv6.
For all other encapsulations, the AERO interface MUST insert an AERO
Header between the UDP header and the next encapsulation header as
shown in Figure 3:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|Version|N|F|C|S| Next Header |Fragment Offset (13 bits)|Res|M|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Identification (32 bits) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Checksum (16 bits) | Signature (variable length) :
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 3: AERO Header
Version a 4-bit "Version" field. MUST be 0 for the purpose of this
specification.
N a 1-bit "Next Header" flag. MUST be 1 for the purpose of this
specification to indicate that "Next Header" field is present.
"Next Header" encodes the IP protocol number corresponding to the
next header in the encapsulation immediately following the AERO
header. For example, "Next Header" encodes the value '4' for
IPv4, '17' for UDP, '41' for IPv6, '47' for GRE, '50' for ESP,
'51' for AH, etc.
F a 1-bit "Fragment Header" flag. Set to '1' if the "Fragment
Offset", "Res", "M", and "Identification" fields are present and
collectively referred to as the "AERO Fragment Header"; otherwise,
set to '0'.
C a 1-bit "Checksum" flag. Set to '1' if the "Checksum" field is
present; otherwise, set to '0'. When present, the Checksum field
contains a checksum of the IP/UDP/AERO encapsulation headers prior
to the Checksum field.
Templin Expires August 14, 2015 [Page 18]
Internet-Draft AERO February 2015
S a 1-bit "Signature" flag. Set to '1' if the "Signature" field is
present; otherwise, set to '0'. When present, the Signature field
contains a cryptographic signature of the encapsulated packet
following the Signature field. The signature is applied prior to
any fragmentation; hence' the Signature field only appears in the
first fragment of a fragmented packet.
(Note: [RFC6706] defines an experimental use in which the bits
corresponding to (Version, N, F, C, S) are all zero, which can be
unambiguously distinguished from the values permitted by this
specification.)
During encapsulation, the AERO interface copies the "TTL/Hop Limit",
"Type of Service/Traffic Class" [RFC2983] and "Congestion
Experienced" [RFC3168] values in the packet's IP header into the
corresponding fields in the encapsulation IP header. (When IPv6 is
used as the encapsulation protocol, the interface also sets the Flow
Label value in the encapsulation header per [RFC6438].) For packets
undergoing re-encapsulation, the AERO interface instead copies the
"TTL/Hop Limit", "Type of Service/Traffic Class", "Flow Label" and
"Congestion Experienced" values in the original encapsulation IP
header into the corresponding fields in the new encapsulation IP
header, i.e., the values are transferred between encapsulation
headers and *not* copied from the encapsulated packet's network-layer
header.
The AERO interface next sets the UDP source port to a constant value
that it will use in each successive packet it sends, and sets the UDP
length field to the length of the encapsulated packet plus 8 bytes
for the UDP header itself, plus the length of the AERO header. For
packets sent via a Server, the AERO interface sets the UDP
destination port to 8060, i.e., the IANA-registered port number for
AERO. For packets sent to a correspondent Client, the AERO interface
sets the UDP destination port to the port value stored in the
neighbor cache entry for this correspondent. The AERO interface also
sets the UDP checksum field to zero (see: [RFC6935][RFC6936]) unless
an integrity check is required (see: Section 3.13.2).
The AERO interface next sets the IP protocol number in the
encapsulation header to 17 (i.e., the IP protocol number for UDP).
When IPv4 is used as the encapsulation protocol, the AERO interface
sets the DF bit as discussed in Section 3.13. The AERO interface
finally sets the AERO header fields as described in Figure 3.
Templin Expires August 14, 2015 [Page 19]
Internet-Draft AERO February 2015
3.11. AERO Interface Decapsulation
AERO interfaces decapsulate packets destined either to the node
itself or to a destination reached via an interface other than the
AERO interface the packet was received on. When the AERO interface
receives a UDP packet, it examines the first octet of the
encapsulated packet.
If the most significant four bits of the first octet encode the value
'4' (i.e., the IP version number value for IPv4) or the value '6'
(i.e., the IP version number value for IPv6), the AERO interface
discards the encapsulation headers and accepts the encapsulated
packet as an ordinary IPv6 or IPv4 data packet, respectively. If the
most significant four bits encode the value '0', however, the AERO
interface processes the packet according to the appropriate AERO
Header fields as specified in Figure 3.
3.12. AERO Interface Data Origin Authentication
AERO nodes employ simple data origin authentication procedures for
encapsulated packets they receive from other nodes on the AERO link.
In particular:
o AERO Relays and Servers accept encapsulated packets with a link-
layer source address that matches a permanent neighbor cache
entry.
o AERO Servers accept authentic encapsulated DHCPv6 messages from
Clients, and create or update a static neighbor cache entry for
the source based on the specific message type.
o AERO Servers accept encapsulated packets if there is a neighbor
cache entry with an AERO address that matches the packet's
network-layer source address and with a link-layer address that
matches the packet's link-layer source address.
o AERO Clients accept encapsulated packets if there is a static
neighbor cache entry with a link-layer source address that matches
the packet's link-layer source address.
o AERO Clients and Servers accept encapsulated packets if there is a
dynamic neighbor cache entry with an AERO address that matches the
packet's network-layer source address, with a link-layer address
that matches the packet's link-layer source address, and with a
non-zero AcceptTime.
Note that this simple data origin authentication is effective in
environments in which link-layer addresses cannot be spoofed. In
Templin Expires August 14, 2015 [Page 20]
Internet-Draft AERO February 2015
other environments, each AERO message must include a signature that
the recipient can use to authenticate the message origin.
3.13. AERO Interface MTU and Fragmentation
The AERO interface is the node's point of attachment to the AERO
link. AERO links over IP networks have a maximum link MTU of 64KB
minus the encapsulation overhead (termed here "ENCAPS"), since the
maximum packet size in the base IP specifications is 64KB
[RFC0791][RFC2460] (while IPv6 jumbograms can be up to 4GB, they are
considered optional for IPv6 nodes [RFC2675][RFC6434]).
IPv6 specifies a minimum link MTU of 1280 bytes [RFC2460]. This is
the minimum packet size the AERO interface MUST admit without
returning an ICMP Packet Too Big (PTB) message. Although IPv4
specifies a smaller minimum link MTU of 68 bytes [RFC0791], AERO
interfaces also observe a 1280 byte minimum for IPv4. Additionally,
the vast majority of links in the Internet configure an MTU of at
least 1500 bytes. Original source hosts have therefore become
conditioned to expect that IP packets up to 1500 bytes in length will
either be delivered to the final destination or a suitable PTB
message returned. However, PTB messages may be lost in the network
[RFC2923] resulting in failure of the IP MTU discovery mechanisms
[RFC1191][RFC1981].
For these reasons, AERO interfaces admit all packets up to 1500 bytes
in length even if some fragmentation is necessary, and admit larger
packets without fragmentation in case they are able to traverse the
tunnel in one piece. AERO interfaces are therefore considered to
have an indefinite MTU, i.e., instead of clamping the MTU to a finite
size.
For AERO links over IPv4, the IP ID field is only 16 bits in length,
meaning that fragmentation at high data rates could result in data
corruption due to reassembly misassociations [RFC6864][RFC4963] (see:
Section 3.13.2). For AERO links over both IPv4 and IPv6, studies
have also shown that IP fragments are dropped unconditionally over
some network paths [I-D.taylor-v6ops-fragdrop]. For these reasons,
when fragmentation is needed it is performed through insertion of an
AERO fragment header (see: Section 3.10) and application of tunnel
fragmentation as described in Section 3.1.7 of [RFC2764]. Since the
AERO fragment header reduces the room available for packet data, but
the original source has no way to control its insertion, the header
length MUST be included in the ENCAPS length even for packets in
which the header does not appear.
Templin Expires August 14, 2015 [Page 21]
Internet-Draft AERO February 2015
The source AERO interface (i.e., the tunnel ingress) therefore sends
encapsulated packets to the destination AERO interface (i.e., the
tunnel egress) according to the following algorithm:
o For IP packets that are no larger than (1280-ENCAPS) bytes, the
tunnel ingress encapsulates the packet and admits it into the
tunnel without fragmentation. For IPv4 AERO links, the tunnel
ingress sets the Don't Fragment (DF) bit to 0 so that these
packets will be delivered to the tunnel egress even if there is a
restricting link in the path, i.e., unless lost due to congestion
or routing errors.
o For IP packets that are larger than (1280-ENCAPS) bytes but no
larger than 1500 bytes, the tunnel ingress encapsulates the packet
and inserts an AERO fragment header. Next, the tunnel ingress
uses the fragmentation algorithm in [RFC2460] to break the packet
into two non-overlapping fragments where the first fragment
(including ENCAPS) is no larger than 1024 bytes and the second is
no larger than the first. Each fragment consists of identical
UDP/IP encapsulation headers, followed by the AERO header followed
by the fragment of the encapsulated packet itself. The tunnel
ingress then admits both fragments into the tunnel, and for IPv4
sets the DF bit to 0 in the IP encapsulation header. These
fragmented encapsulated packets will be delivered to the tunnel
egress. When the tunnel egress receives the fragments, it
reassembles them into a whole packet per the reassembly algorithm
in [RFC2460]. The tunnel egress therefore MUST be capable of
reassembling packets up to 1500+ENCAPS bytes in length; hence, it
is RECOMMENDED that the tunnel egress be capable of reassembling
at least 2KB.
o For IPv4 packets that are larger than 1500 bytes and with the DF
bit set to 0, the tunnel ingress uses ordinary IPv4 fragmentation
to break the unencapsulated packet into a minimum number of non-
overlapping fragments where the first fragment is no larger than
1024-ENCAPS and all other fragments are no larger than the first
fragment. The tunnel ingress then encapsulates each fragment (and
for IPv4 sets the DF bit to 0) then admits them into the tunnel.
These fragments will be delivered to the final destination via the
tunnel egress.
o For all other IP packets, if the packet is too large to enter the
underlying interface following encapsulation, the tunnel ingress
drops the packet and returns a network-layer (L3) PTB message to
the original source with MTU set to the larger of 1500 bytes or
the underlying interface MTU minus ENCAPS. Otherwise, the tunnel
ingress encapsulates the packet and admits it into the tunnel
without fragmentation (and for IPv4 sets the DF bit to 1) and
Templin Expires August 14, 2015 [Page 22]
Internet-Draft AERO February 2015
translates any link-layer (L2) PTB messages it may receive from
the network into corresponding L3 PTB messages to send to the
original source as specified in Section 3.14. Since both L2 and
L3 PTB messages may be either lost or contain insufficient
information, however, it is RECOMMENDED that original sources that
send unfragmentable IP packets larger than 1500 bytes use
Packetization Layer Path MTU Discovery (PLPMTUD) [RFC4821].
While sending packets according to the above algorithm, the tunnel
ingress MAY also send 1500 byte or larger probe packets to determine
whether they can reach the tunnel egress without fragmentation. If
the probes succeed, the tunnel ingress can discontinue fragmentation
and (for IPv4) set DF to 1. Since the path MTU within the tunnel may
fluctuate due to routing changes, the tunnel ingress SHOULD continue
to send additional probes subject to rate limiting and SHOULD process
any L2 PTB messages as an indication that the path MTU may have
decreased. If the path MTU within the tunnel becomes insufficient,
the source MUST resume fragmentation.
To construct a probe, the tunnel ingress prepares an NS message with
a Nonce option plus trailing NULL padding octets added to the probe
length without including the length of the padding in the IPv6
Payload Length field, but with the length included in the
encapsulating IP header. The tunnel ingress then encapsulates the
padded NS message in the encapsulation headers (and for IPv4 sets DF
to 1) then sends the message to the tunnel egress. If the tunnel
egress returns a solicited NA message with a matching Nonce option,
the tunnel ingress deems the probe successful. Note that in this
process it is essential that probes follow equivalent paths to those
used to convey actual data packets. This means that Equal Cost
MultiPath (ECMP) and Link Aggregation Gateway (LAG) equipment is
assumed to support identical MTUs along all paths.
3.13.1. Accommodating Large Control Messages
Control messages (i.e., IPv6 ND, DHCPv6, etc.) MUST be accommodated
even if some fragmentation is necessary. These packets are therefore
accommodated through a modification of the second rule in the above
algorithm as follows:
o For control messages that are larger than (1280-ENCAPS) bytes, the
tunnel ingress encapsulates the packet and inserts an AERO
fragment header. Next, the tunnel ingress uses the fragmentation
algorithm in [RFC2460] to break the packet into a minimum number
of non-overlapping fragments where the first fragment (including
ENCAPS) is no larger than 1024 bytes and the remaining fragments
are no larger than the first. The tunnel ingress then
Templin Expires August 14, 2015 [Page 23]
Internet-Draft AERO February 2015
encapsulates each fragment (and for IPv4 sets the DF bit to 0)
then admits them into the tunnel.
Control messages that exceed the 2KB minimum reassembly size rarely
occur in the modern era, however the tunnel egress SHOULD be able to
reassemble them if they do. This means that the tunnel egress SHOULD
include a configuration knob allowing the operator to set a larger
reassembly buffer size if large control messages become more common
in the future.
The tunnel ingress can send large control messages without
fragmentation if there is assurance that large packets can traverse
the tunnel without fragmentation. The tunnel ingress MAY send 1500
byte or larger probe packets as specified above to determine a size
for which fragmentation can be avoided.
3.13.2. Integrity
When fragmentation is needed, there must be assurance that reassembly
can be safely conducted without incurring data corruption. Sources
of corruption can include implementation errors, memory errors and
misassociation of fragments from a first datagram with fragments of
another datagram. The first two conditions (implementation and
memory errors) are mitigated by modern systems and implementations
that have demonstrated integrity through decades of operational
practice. The third condition (reassembly misassociations) must be
accounted for by AERO.
The AERO fragmentation procedure described in the above algorithms
reuses standard IPv6 fragmentation and reassembly code. Since the
AERO fragment header includes a 32-bit ID field, there would need to
be 2^32 packets alive in the network before a second packet with a
duplicate ID enters the system with the (remote) possibility for a
reassembly misassociation. For 1280 byte packets, and for a maximum
network lifetime value of 60 seconds[RFC2460], this means that the
tunnel ingress would need to produce ~(7 *10^12) bits/sec in order
for a duplication event to be possible. This exceeds the bandwidth
of data link technologies of the modern era, but not necessarily so
going forward into the future. Although wireless data links commonly
used by AERO Clients support vastly lower data rates, the aggregate
data rates between AERO Servers and Relays may be substantial.
However, high speed data links in the network core are expected to
configure larger MTUs, e.g., 4KB, 8KB or even larger such that
unfragmented packets can be used. Hence, no integrity check is
included to cover the AERO fragmentation and reassembly procedures.
When the tunnel ingress sends an IPv4-encapsulated packet with the DF
bit set to 0 in the above algorithms, there is a chance that the
Templin Expires August 14, 2015 [Page 24]
Internet-Draft AERO February 2015
packet may be fragmented by an IPv4 router somewhere within the
tunnel. Since the largest such packet is only 1280 bytes, however,
it is very likely that the packet will traverse the tunnel without
incurring a restricting link. Even when a link within the tunnel
configures an MTU smaller than 1280 bytes, it is very likely that it
does so due to limited performance characteristics [RFC3819]. This
means that the tunnel would not be able to convey fragmented
IPv4-encapsulated packets fast enough to produce reassembly
misassociations, as discussed above. However, AERO must also account
for the possibility of tunnel paths that include "poorly managed"
IPv4 link MTUs due to misconfigurations.
Since the IPv4 header includes only a 16-bit ID field, there would
only need to be 2^16 packets alive in the network before a second
packet with a duplicate ID enters the system. For 1280 byte packets,
and for a maximum network lifetime value of 120 seconds[RFC0791],
this means that the tunnel ingress would only need to produce ~(5
*10^6) bits/sec in order for a duplication event to be possible - a
value that is well within range for many modern wired and wireless
data link technologies.
Therefore, if there is strong operational assurance that no IPv4
links capable of supporting data rates of 5Mbps or more configure an
MTU smaller than 1280 the tunnel ingress MAY omit an integrity check
for the IPv4 fragmentation and reassembly procedures; otherwise, the
tunnel ingress SHOULD include an integrity check. When an upper
layer encapsulation (e.g., IPsec) already includes an integrity
check, the tunnel ingress need not include an additional check.
Otherwise, the tunnel ingress calculates the UDP checksum over the
encapsulated packet and writes the value into the UDP encapsulation
header, i.e., instead of writing the value 0. The tunnel egress will
then verify the UDP checksum and discard the packet if the checksum
is incorrect.
3.14. AERO Interface Error Handling
When an AERO node admits encapsulated packets into the AERO
interface, it may receive link-layer (L2) or network-layer (L3) error
indications.
An L2 error indication is an ICMP error message generated by a router
on the path to the neighbor or by the neighbor itself. The message
includes an IP header with the address of the node that generated the
error as the source address and with the link-layer address of the
AERO node as the destination address.
The IP header is followed by an ICMP header that includes an error
Type, Code and Checksum. For ICMPv6 [RFC4443], the error Types
Templin Expires August 14, 2015 [Page 25]
Internet-Draft AERO February 2015
include "Destination Unreachable", "Packet Too Big (PTB)", "Time
Exceeded" and "Parameter Problem". For ICMPv4 [RFC0792], the error
Types include "Destination Unreachable", "Fragmentation Needed" (a
Destination Unreachable Code that is analogous to the ICMPv6 PTB),
"Time Exceeded" and "Parameter Problem".
The ICMP header is followed by the leading portion of the packet that
generated the error, also known as the "packet-in-error". For
ICMPv6, [RFC4443] specifies that the packet-in-error includes: "As
much of invoking packet as possible without the ICMPv6 packet
exceeding the minimum IPv6 MTU" (i.e., no more than 1280 bytes). For
ICMPv4, [RFC0792] specifies that the packet-in-error includes:
"Internet Header + 64 bits of Original Data Datagram", however
[RFC1812] Section 4.3.2.3 updates this specification by stating: "the
ICMP datagram SHOULD contain as much of the original datagram as
possible without the length of the ICMP datagram exceeding 576
bytes".
The L2 error message format is shown in Figure 4:
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
~ ~
| L2 IP Header of |
| error message |
~ ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| L2 ICMP Header |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ ---
~ ~ P
| IP and other encapsulation | a
| headers of original L3 packet | c
~ ~ k
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ e
~ ~ t
| IP header of |
| original L3 packet | i
~ ~ n
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
~ ~ e
| Upper layer headers and | r
| leading portion of body | r
| of the original L3 packet | o
~ ~ r
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ ---
Figure 4: AERO Interface L2 Error Message Format
Templin Expires August 14, 2015 [Page 26]
Internet-Draft AERO February 2015
The AERO node rules for processing these L2 error messages is as
follows:
o When an AERO node receives an L2 Parameter Problem message, it
processes the message the same as described as for ordinary ICMP
errors in the normative references [RFC0792][RFC4443].
o When an AERO node receives persistent L2 IPv4 Time Exceeded
messages, the IP ID field may be wrapping before earlier fragments
have been processed. In that case, the node SHOULD begin
including IPv4 integrity checks (see: Section 3.13.2).
o When an AERO Client receives persistent L2 Destination Unreachable
messages in response to tunneled packets that it sends to one of
its dynamic neighbor correspondents, the Client SHOULD test the
path to the correspondent using Neighbor Unreachability Detection
(NUD) (see Section 3.18). If NUD fails, the Client SHOULD set
ForwardTime for the corresponding dynamic neighbor cache entry to
0 and allow future packets destined to the correspondent to flow
through a Server.
o When an AERO Client receives persistent L2 Destination Unreachable
messages in response to tunneled packets that it sends to one of
its static neighbor Servers, the Client SHOULD test the path to
the Server using NUD. If NUD fails, the Client SHOULD delete the
neighbor cache entry and attempt to associate with a new Server.
o When an AERO Server receives persistent L2 Destination Unreachable
messages in response to tunneled packets that it sends to one of
its static neighbor Clients, the Server SHOULD test the path to
the Client using NUD. If NUD fails, the Server SHOULD cancel the
DHCPv6 PD for the Client's ACP, withdraw its route for the ACP
from the AERO routing system and delete the neighbor cache entry
(see Section 3.18 and Section 3.19).
o When an AERO Relay or Server receives an L2 Destination
Unreachable message in response to a tunneled packet that it sends
to one of its permanent neighbors, it discards the message since
the routing system is likely in a temporary transitional state
that will soon re-converge.
o When an AERO node receives an L2 PTB message, it translates the
message into an L3 PTB message if possible (*) and forwards the
message toward the original source as described below.
To translate an L2 PTB message to an L3 PTB message, the AERO node
first caches the MTU field value of the L2 ICMP header. The node
next discards the L2 IP and ICMP headers, and also discards the
Templin Expires August 14, 2015 [Page 27]
Internet-Draft AERO February 2015
encapsulation headers of the original L3 packet. Next the node
encapsulates the included segment of the original L3 packet in an L3
IP and ICMP header, and sets the ICMP header Type and Code values to
appropriate values for the L3 IP protocol. In the process, the node
writes the maximum of 1500 bytes and (L2 MTU - ENCAPS) into the MTU
field of the L3 ICMP header.
The node next writes the IP source address of the original L3 packet
as the destination address of the L3 PTB message and determines the
next hop to the destination. If the next hop is reached via the AERO
interface, the node uses the IPv6 address "::" or the IPv4 address
"0.0.0.0" as the IP source address of the L3 PTB message. Otherwise,
the node uses one of its non link-local addresses as the source
address of the L3 PTB message. The node finally calculates the ICMP
checksum over the L3 PTB message and writes the Checksum in the
corresponding field of the L3 ICMP header. The L3 PTB message
therefore is formatted as follows:
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
~ ~
| L3 IP Header of |
| error message |
~ ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| L3 ICMP Header |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ ---
~ ~ p
| IP header of | k
| original L3 packet | t
~ ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ i
~ ~ n
| Upper layer headers and |
| leading portion of body | e
| of the original L3 packet | r
~ ~ r
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ ---
Figure 5: AERO Interface L3 Error Message Format
After the node has prepared the L3 PTB message, it either forwards
the message via a link outside of the AERO interface without
encapsulation, or encapsulates and forwards the message to the next
hop via the AERO interface.
When an AERO Relay receives an L3 packet for which the destination
address is covered by an ASP, if there is no more-specific routing
information for the destination the Relay drops the packet and
Templin Expires August 14, 2015 [Page 28]
Internet-Draft AERO February 2015
returns an L3 Destination Unreachable message. The Relay first
writes the IP source address of the original L3 packet as the
destination address of the L3 Destination Unreachable message and
determines the next hop to the destination. If the next hop is
reached via the AERO interface, the Relay uses the IPv6 address "::"
or the IPv4 address "0.0.0.0" as the IP source address of the L3
Destination Unreachable message and forwards the message to the next
hop within the AERO interface. Otherwise, the Relay uses one of its
non link-local addresses as the source address of the L3 Destination
Unreachable message and forwards the message via a link outside the
AERO interface.
When an AERO node receives any L3 error message via the AERO
interface, it examines the destination address in the L3 IP header of
the message. If the next hop toward the destination address of the
error message is via the AERO interface, the node re-encapsulates and
forwards the message to the next hop within the AERO interface.
Otherwise, if the source address in the L3 IP header of the message
is the IPv6 address "::" or the IPv4 address "0.0.0.0", the node
writes one of its non link-local addresses as the source address of
the L3 message and recalculates the IP and/or ICMP checksums. The
node finally forwards the message via a link outside of the AERO
interface.
(*) Note that in some instances the packet-in-error field of an L2
PTB message may not include enough information for translation to an
L3 PTB message. In that case, the AERO interface simply discards the
L2 PTB message. It can therefore be said that translation of L2 PTB
messages to L3 PTB messages can provide a useful optimization when
possible, but is not critical for sources that correctly use PLPMTUD.
3.15. AERO Router Discovery, Prefix Delegation and Address
Configuration
3.15.1. AERO DHCPv6 Service Model
Each AERO Server configures a DHCPv6 server function to facilitate PD
requests from Clients. Each Server is provisioned with a database of
ACP-to-Client ID mappings for all Clients enrolled in the AERO
system, as well as any information necessary to authenticate each
Client. The Client database is maintained by a central
administrative authority for the AERO link and securely distributed
to all Servers, e.g., via a service such as the Lightweight Directory
Access Protocol (LDAP) [RFC4511] or a similar prefix/host reservation
system.
Therefore, no Server-to-Server DHCPv6 PD delegation state
synchronization is necessary, and Clients can optionally hold
Templin Expires August 14, 2015 [Page 29]
Internet-Draft AERO February 2015
separate delegations for the same ACP from multiple Servers. In this
way, Clients can associate with multiple Servers, and can receive new
delegations from new Servers before deprecating delegations received
from existing Servers.
AERO Clients and Servers exchange Client link-layer address
information using an option format similar to the Client Link Layer
Address Option (CLLAO) defined in [RFC6939]. Due to practical
limitations of CLLAO, however, AERO interfaces instead use a Vendor-
Specific Information Option as described in the following sections.
3.15.2. AERO Client Behavior
AERO Clients discover the link-layer addresses of AERO Servers via
static configuration, or through an automated means such as DNS name
resolution. In the absence of other information, the Client resolves
the FQDN "linkupnetworks.[domainname]" where "linkupnetworks" is a
constant text string and "[domainname]" is the connection-specific
DNS suffix for the Client's underlying network connection (e.g.,
"example.com"). After discovering the link-layer addresses, the
Client associates with one or more of the corresponding Servers.
To associate with a Server, the Client acts as a requesting router to
request an ACP through a DHCPv6 PD request [RFC3315][RFC3633] with
fe80::ffff:ffff:ffff:ffff as the IPv6 source address,
'All_DHCP_Relay_Agents_and_Servers' as the IPv6 destination address
and the link-layer address of the Server as the link-layer
destination address. The Client also includes a Client Identifier
option with a DHCP Unique Identifier (DUID) and an Identity
Association for Prefix Delegation (IA_PD) option. If the Client is
pre-provisioned with an ACP associated with the AERO service, it MAY
also include the ACP in the IA_PD to indicate its preference to the
DHCPv6 server.
The Client also includes an AERO Link-Layer Address Request (ALLAREQ)
option with the format shown in Figure 6:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| OPTION_VENDOR_OPTS | option-len |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| enterprise-number (=45282) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = 0 | Reserved | Link ID | Preference |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 6: AERO Link-Layer Address Request (ALLAREQ) Option
Templin Expires August 14, 2015 [Page 30]
Internet-Draft AERO February 2015
In the above format, the Client sets 'option-code' to
OPTION_VENDOR_OPTS, sets 'option-len' to 8, sets 'enterprise-number'
to 45282 (see: IANA Considerations), sets 'Type' to 0 to indicate
"AERO Link-Layer Address Request (ALLAREQ) option, and sets
'Reserved' to 0. The Client then sets appropriate 'Link ID' and
'Preference' values for the underlying interface over which the
DHCPv6 PD request will be issued the same as for an S/TLLAO as shown
in Figure 2. (The Client MAY instead omit the ALLAREQ option; in
that case, the Server considers the message the same as if the Client
had inserted an ALLAREQ option with 'Link ID' set to 0 and
'Preference' set to 255.) The Client finally includes any necessary
authentication options to identify itself to the DHCPv6 server, and
sends the encapsulated DHCPv6 PD request via the underlying
interface.
When the Client receives its ACP via a DHCPv6 Reply from the AERO
Server, it creates a static neighbor cache entry with the Server's
link-local address as the network-layer address and the Server's
encapsulation address as the link-layer address. If the Reply
message contains an AERO Service Prefix Advertisement (ASPADV) option
(see: Section 3.15.3) the Client also caches each ASP in the option.
The Client then considers the link-layer address of the Server as the
primary default encapsulation address for forwarding packets for
which there is no more-specific forwarding information. The Client
can also examine the UDP Port Number and IP Address in the AERO Link-
Layer Address Reply (ALLAREP) option of the Reply message to
determine it's link-layer address from the perspective of the Server,
which may be different than from its own perspective (see:
Section 3.15.3).
Next, the Client assigns the AERO address constructed from the
delegated ACP to the AERO interface and sub-delegates the ACP to
nodes and links within its attached EUNs (the AERO address thereafter
remains stable as the Client moves). The Client also assigns a
default IP route to the AERO interface as a route-to-interface, i.e.,
with no explicit next-hop. The next hop will then be determined
after a packet has been submitted to the AERO interface by inspecting
the neighbor cache (see above).
On some platforms (e.g., popular cell phone operating systems), the
act of assigning a default IPv6 route may not be permitted from a
user application due to security policy. Typically, those platforms
include a TUN/TAP interface that acts as a point-to-point conduit
between user applications and the AERO interface. In that case, the
Client can instead generate a "synthesized RA" message. The message
conforms to [RFC4861] and is prepared as follows:
o the IPv6 source address is the Client's AERO address
Templin Expires August 14, 2015 [Page 31]
Internet-Draft AERO February 2015
o the IPv6 destination address is all-nodes multicast
o the Router Lifetime is set to a time that is no longer than the
ACP DHCPv6 lifetime
o the message does not include a Source Link Layer Address Option
(SLLAO)
o the message includes a Prefix Information Option (PIO) with a /64
prefix taken from the ACP as the prefix for autoconfiguration
The Client then sends the synthesized RA message via the TUN/TAP
interface, where the operating system kernel will interpret it as
though it were generated by an actual router. The operating system
will then install a default route and use StateLess Address
AutoConfiguration (SLAAC) to configure an IPv6 address on the TUN/TAP
interface. Methods for similarly installing an IPv4 default route
and IPv4 address on the TUN/TAP interface are based on synthesized
DHCPv4 messages [RFC2131].
The Client subsequently renews its ACP delegation through each of its
Servers by performing DHCPv6 Renew/Reply exchanges with its AERO
address as the IPv6 source address,
'All_DHCP_Relay_Agents_and_Servers' as the IPv6 destination address,
the link-layer address of a Server as the link-layer destination
address and the same Client identifier, authentication options and
ALLAREQ as was used in the initial PD request. Note that if the
Client does not issue a DHCPv6 Renew before the delegation expires
(e.g., if the Client has been out of touch with the Server for a
considerable amount of time) it must re-initiate the DHCPv6 PD
procedure. If the Client sends synthesized RA and/or DHCPv4 messages
(see above), it also sends a new synthesized message when issuing a
DHCPv6 Renew or when re-initiating the DHCPv6 PD procedure.
Since the Client's AERO address is obtained from the unique ACP
delegation it receives, there is no need for Duplicate Address
Detection (DAD) on AERO links. Other nodes maliciously attempting to
hijack an authorized Client's AERO address will be denied access to
the network by the DHCPv6 server due to an unacceptable link-layer
address and/or security parameters (see: Security Considerations).
3.15.3. AERO Server Behavior
AERO Servers configure a DHCPv6 server function on their AERO links.
AERO Servers arrange to add their encapsulation layer IP addresses
(i.e., their link-layer addresses) to the DNS resource records for
the FQDN "linkupnetworks.[domainname]" before entering service.
Templin Expires August 14, 2015 [Page 32]
Internet-Draft AERO February 2015
When an AERO Server receives a prospective Client's DHCPv6 PD message
on its AERO interface, it first authenticates the message. If
authentication succeeds, the Server determines the correct ACP to
delegate to the Client by searching the Client database. In
environments where spoofing is not considered a threat, the Server
MAY use the Client's DUID as the identification value. Otherwise,
the Server SHOULD use a signed certificate provided by the Client.
The Server then delegates the ACP and creates an IP forwarding table
entry so that the AERO routing system will propagate the ACP to all
Relays (see: Section 3.7). Next, the Server prepares a DHCPv6 Reply
message to send to the Client while using fe80::ID as the IPv6 source
address, the link-local address taken from the Client's request as
the IPv6 destination address, the Server's link-layer address as the
source link-layer address, and the Client's link-layer address as the
destination link-layer address. The server also includes an IA_PD
option with the delegated ACP.
The Server also includes an AERO Link-Layer Address Reply (ALLAREP)
option filled out with the UDP Port Number and IP Address values it
observed when it received the ALLAREQ in the Client's original DHCPv6
message. The ALLAREP option is formatted as shown in Figure 7:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| OPTION_VENDOR_OPTS | option-len |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| enterprise-number (=45282) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = 1 | Reserved | Link ID | Preference |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| UDP Port Number | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ +
| |
+ +
| IP Address |
+ +
| |
+ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 7: AERO Link-Layer Address Reply (ALLAREP) Option
In the ALLAREP, the Server sets 'option-code' to OPTION_VENDOR_OPTS,
sets 'option-length' to 26, sets 'enterprise-number' to 45282, sets
'Type' to 1 and sets 'Reserved' to 0. Next, the Server sets 'Link
Templin Expires August 14, 2015 [Page 33]
Internet-Draft AERO February 2015
ID' and 'Preference' to the same values that appeared in the ALLAREQ,
and sets 'UDP Port Number' and 'IP address' to the Client's link-
layer address. Note that if the Client did not include an ALAREQ
option in its DHCPv6 message, the Server MUST still include an
ALLAREP option in the corresponding reply with 'Link ID' set to 0 and
'Preference' set to 255.
The Server next includes an AERO Service Prefix Advertisement Option
(ASPADV) formatted as shown inFigure 8 :
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| OPTION_VENDOR_OPTS | option-len |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| enterprise-number (=45282) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = 2 | Reserved | Prefix Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ ASP (1) +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Reserved | Prefix Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ ASP (2) +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Reserved | Prefix Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ ASP (3) +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
. (etc.) .
. .
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 8: AERO Service Prefix Advertisement (ASPADV) Option
In the ASPADV, the Server sets 'option-code' to OPTION_VENDOR_OPTS,
sets 'option-length' to the length of the option, sets 'enterprise-
number' to 45282, sets 'Type' to 2 and sets 'Reserved' to 0. Next,
the Server includes one or more ASP with the IP prefix as it would
appear in the interface identifier portion of the corresponding AERO
address (see: Section 3.3). For IPv6, valid values for the Prefix
Length field are 0 through 64; for IPv4, valid values are 0 through
32.
Templin Expires August 14, 2015 [Page 34]
Internet-Draft AERO February 2015
When the Server's DHCPv6 function admits the DHCPv6 Reply message
into the AERO interface, the interface creates a static neighbor
cache entry for the Client's AERO address with lifetime set to no
more than the delegation lifetime and the Client's link-layer address
as the link-layer address for the Link ID specified in the ALLAREP
option. The AERO interface then uses the Client link-layer address
information in the ALLAREP option as the link-layer address for
encapsulation.
After the initial DHCPv6 PD exchange, the AERO Server maintains the
neighbor cache entry for the Client until the delegation lifetime
expires. If the Client issues a Renew/Reply exchange, the Server
extends the lifetime. If the Client issues a Release/Reply, or if
the Client does not issue a Renew/Reply before the lifetime expires,
the Server deletes the neighbor cache entry for the Client and
withdraws the IP route from the AERO routing system.
3.15.3.1. Lightweight DHCPv6 Relay Agent (LDRA)
AERO Clients and Servers are always on the same link from the
perspective of DHCPv6. However, in some implementations the DHCPv6
server and AERO interface driver may be located in separate modules
that preclude information sharing through standard APIs. In that
case, the AERO interface driver module can act as a Lightweight
DHCPv6 Relay Agent (LDRA)[RFC6221] "bump in the wire" to include an
ALLAREP option and any other options in a Relay-Forward message
encapsulation to the DHCPv6 Server. The AERO interface driver
prepares an ALLAREP option with the 'UDP Port Number' and 'IP
Address' taken from the Client's link-layer address and writes the
values found in the ALLAREQ option in the 'Link ID' and 'Preference'
fields. The AERO interface driver then wraps the ALLAREP option in a
Relay-Supplied DHCP Option [RFC6422], incorporates the option into
the Relay-Forward message and forwards the message to the DHCPv6
server.
When the DHCPv6 server receives the Relay-Forward message, it caches
the ALLAREP option and authenticates the encapsulated DHCPv6 message.
When the DHCPv6 server prepares a Reply message, it then includes the
ALLAREP option in the body of the message along with any other
options, then wraps the message in a Relay-Reply message. The DHCPv6
server then delivers the Relay-Reply message to the AERO interface
driver, where the Relay-Reply wrapper is discarded through the
application of LDRA and the DHCPv6 message is delivered to the
Client.
Templin Expires August 14, 2015 [Page 35]
Internet-Draft AERO February 2015
3.16. AERO Forwarding Agent Discovery
AERO Relays, Servers and Clients MAY associate with one or more
companion AERO Forwarding Agents as platforms for offloading high-
speed data plane traffic. AERO nodes distribute forwarding
information to Forwarding Agents via an out-of-band messaging service
(e.g., NETCONF [RFC6241], etc.).
When an AERO node receives a data packet on an AERO interface with a
network layer destination address for which it has distributed
forwarding information to one or more Forwarding Agents, the node
returns an RA message to the source neighbor (subject to rate
limiting) then forwards the data packet as usual. The RA message
includes one or more SLLAOs with the link-layer addresses of
candidate Forwarding Engines.
If the forwarding information pertains only to a specific ACP, the
AERO node sets the network-layer source address of the RA to the AERO
address corresponding to the ACP, and sets the default router
lifetime to 0. If the forwarding information pertains to all
addresses, the AERO node instead sets the network-layer source
address of the RA to its own link-local address and sets the default
router lifetime to a non-zero value.
When the source neighbor receives the RA message, it SHOULD record
the link-layer addresses in the SLLAOs as the encapsulation addresses
to use for sending subsequent data packets with addresses that match
the information in the RA. However, the source MUST continue to use
the primary link-layer address of the AERO node as the encapsulation
address for sending control messages.
3.17. AERO Intradomain Route Optimization
When a source Client forwards packets to a prospective correspondent
Client within the same AERO link domain (i.e., one for which the
packet's destination address is covered by an ASP), the source Client
initiates an intra-domain AERO route optimization procedure. The
procedure is based on an exchange of IPv6 ND messages using a chain
of AERO Servers and Relays as a trust basis. This procedure is in
contrast to the Return Routability procedure required for route
optimization to a correspondent Client located in the Internet as
described in Section 3.22. The following sections specify the AERO
intradomain route optimization procedure.
Templin Expires August 14, 2015 [Page 36]
Internet-Draft AERO February 2015
3.17.1. Reference Operational Scenario
Figure 9 depicts the AERO intradomain route optimization reference
operational scenario, using IPv6 addressing as the example (while not
shown, a corresponding example for IPv4 addressing can be easily
constructed). The figure shows an AERO Relay ('R1'), two AERO
Servers ('S1', 'S2'), two AERO Clients ('C1', 'C2') and two ordinary
IPv6 hosts ('H1', 'H2'):
+--------------+ +--------------+ +--------------+
| Server S1 | | Relay R1 | | Server S2 |
+--------------+ +--------------+ +--------------+
fe80::2 fe80::1 fe80::3
L2(S1) L2(R1) L2(S2)
| | |
X-----+-----+------------------+-----------------+----+----X
| AERO Link |
L2(A) L2(B)
fe80::2001:db8:0:0 fe80::2001:db8:1:0
+--------------+ +--------------+
|AERO Client C1| |AERO Client C2|
+--------------+ +--------------+
2001:DB8:0::/48 2001:DB8:1::/48
| |
.-. .-.
,-( _)-. 2001:db8:0::1 2001:db8:1::1 ,-( _)-.
.-(_ IP )-. +---------+ +---------+ .-(_ IP )-.
(__ EUN )--| Host H1 | | Host H2 |--(__ EUN )
`-(______)-' +---------+ +---------+ `-(______)-'
Figure 9: AERO Reference Operational Scenario
In Figure 9, Relay ('R1') assigns the address fe80::1 to its AERO
interface with link-layer address L2(R1), Server ('S1') assigns the
address fe80::2 with link-layer address L2(S1),and Server ('S2')
assigns the address fe80::3 with link-layer address L2(S2). Servers
('S1') and ('S2') next arrange to add their link-layer addresses to a
published list of valid Servers for the AERO link.
AERO Client ('C1') receives the ACP 2001:db8:0::/48 in a DHCPv6 PD
exchange via AERO Server ('S1') then assigns the address
fe80::2001:db8:0:0 to its AERO interface with link-layer address
L2(C1). Client ('C1') configures a default route and neighbor cache
entry via the AERO interface with next-hop address fe80::2 and link-
layer address L2(S1), then sub-delegates the ACP to its attached
EUNs. IPv6 host ('H1') connects to the EUN, and configures the
address 2001:db8:0::1.
Templin Expires August 14, 2015 [Page 37]
Internet-Draft AERO February 2015
AERO Client ('C2') receives the ACP 2001:db8:1::/48 in a DHCPv6 PD
exchange via AERO Server ('S2') then assigns the address
fe80::2001:db8:1:0 to its AERO interface with link-layer address
L2(C2). Client ('C2') configures a default route and neighbor cache
entry via the AERO interface with next-hop address fe80::3 and link-
layer address L2(S2), then sub-delegates the ACP to its attached
EUNs. IPv6 host ('H1') connects to the EUN, and configures the
address 2001:db8:1::1.
3.17.2. Concept of Operations
Again, with reference to Figure 9, when source host ('H1') sends a
packet to destination host ('H2'), the packet is first forwarded over
the source host's attached EUN to Client ('C1'). Client ('C1') then
forwards the packet via its AERO interface to Server ('S1') and also
sends a Predirect message toward Client ('C2') via Server ('S1').
Server ('S1') then re-encapsulates and forwards both the packet and
the Predirect message out the same AERO interface toward Client
('C2') via Relay ('R1').
When Relay ('R1') receives the packet and Predirect message, it
consults its forwarding table to discover Server ('S2') as the next
hop toward Client ('C2'). Relay ('R1') then forwards both the packet
and the Predirect message to Server ('S2'), which then forwards them
to Client ('C2').
After Client ('C2') receives the Predirect message, it process the
message and returns a Redirect message toward Client ('C1') via
Server ('S2'). During the process, Client ('C2') also creates or
updates a dynamic neighbor cache entry for Client ('C1').
When Server ('S2') receives the Redirect message, it re-encapsulates
the message and forwards it on to Relay ('R1'), which forwards the
message on to Server ('S1') which forwards the message on to Client
('C1'). After Client ('C1') receives the Redirect message, it
processes the message and creates or updates a dynamic neighbor cache
entry for Client ('C2').
Following the above Predirect/Redirect message exchange, forwarding
of packets from Client ('C1') to Client ('C2') without involving any
intermediate nodes is enabled. The mechanisms that support this
exchange are specified in the following sections.
3.17.3. Message Format
AERO Redirect/Predirect messages use the same format as for ICMPv6
Redirect messages depicted in Section 4.5 of [RFC4861], but also
include a new "Prefix Length" field taken from the low-order 8 bits
Templin Expires August 14, 2015 [Page 38]
Internet-Draft AERO February 2015
of the Redirect message Reserved field. For IPv6, valid values for
the Prefix Length field are 0 through 64; for IPv4, valid values are
0 through 32. The Redirect/Predirect messages are formatted as shown
in Figure 10:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type (=137) | Code (=0/1) | Checksum |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Reserved | Prefix Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ +
| |
+ Target Address +
| |
+ +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ +
| |
+ Destination Address +
| |
+ +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Options ...
+-+-+-+-+-+-+-+-+-+-+-+-
Figure 10: AERO Redirect/Predirect Message Format
3.17.4. Sending Predirects
When a Client forwards a packet with a source address from one of its
ACPs toward a destination address covered by an ASP (i.e., toward
another AERO Client connected to the same AERO link), the source
Client MAY send a Predirect message forward toward the destination
Client via the Server.
In the reference operational scenario, when Client ('C1') forwards a
packet toward Client ('C2'), it MAY also send a Predirect message
forward toward Client ('C2'), subject to rate limiting (see
Section 8.2 of [RFC4861]). Client ('C1') prepares the Predirect
message as follows:
Templin Expires August 14, 2015 [Page 39]
Internet-Draft AERO February 2015
o the link-layer source address is set to 'L2(C1)' (i.e., the link-
layer address of Client ('C1')).
o the link-layer destination address is set to 'L2(S1)' (i.e., the
link-layer address of Server ('S1')).
o the network-layer source address is set to fe80::2001:db8:0:0
(i.e., the AERO address of Client ('C1')).
o the network-layer destination address is set to fe80::2001:db8:1:0
(i.e., the AERO address of Client ('C2')).
o the Type is set to 137.
o the Code is set to 1 to indicate "Predirect".
o the Prefix Length is set to the length of the prefix to be
assigned to the Target Address.
o the Target Address is set to fe80::2001:db8:0:0 (i.e., the AERO
address of Client ('C1')).
o the Destination Address is set to the source address of the
originating packet that triggered the Predirection event. (If the
originating packet is an IPv4 packet, the address is constructed
in IPv4-compatible IPv6 address format).
o the message includes one or more TLLAOs with Link ID and
Preference set to appropriate values for Client ('C1')'s
underlying interfaces, and with UDP Port Number and IP Address set
to 0'.
o the message SHOULD include a Timestamp option and a Nonce option.
o the message includes a Redirected Header Option (RHO) that
contains the originating packet truncated if necessary to ensure
that at least the network-layer header is included but the size of
the message does not exceed 1280 bytes.
Note that the act of sending Predirect messages is cited as "MAY",
since Client ('C1') may have advanced knowledge that the direct path
to Client ('C2') would be unusable or otherwise undesirable. If the
direct path later becomes unusable after the initial route
optimization, Client ('C1') simply allows packets to again flow
through Server ('S1').
Templin Expires August 14, 2015 [Page 40]
Internet-Draft AERO February 2015
3.17.5. Re-encapsulating and Relaying Predirects
When Server ('S1') receives a Predirect message from Client ('C1'),
it first verifies that the TLLAOs in the Predirect are a proper
subset of the Link IDs in Client ('C1')'s neighbor cache entry. If
the Client's TLLAOs are not acceptable, Server ('S1') discards the
message. Otherwise, Server ('S1') validates the message according to
the ICMPv6 Redirect message validation rules in Section 8.1 of
[RFC4861], except that the Predirect has Code=1. Server ('S1') also
verifies that Client ('C1') is authorized to use the Prefix Length in
the Predirect when applied to the AERO address in the network-layer
source address by searching for the AERO address in the neighbor
cache. If validation fails, Server ('S1') discards the Predirect;
otherwise, it copies the correct UDP Port numbers and IP Addresses
for Client ('C1')'s links into the (previously empty) TLLAOs.
Server ('S1') then examines the network-layer destination address of
the Predirect to determine the next hop toward Client ('C2') by
searching for the AERO address in the neighbor cache. Since Client
('C2') is not one of its neighbors, Server ('S1') re-encapsulates the
Predirect and relays it via Relay ('R1') by changing the link-layer
source address of the message to 'L2(S1)' and changing the link-layer
destination address to 'L2(R1)'. Server ('S1') finally forwards the
re-encapsulated message to Relay ('R1') without decrementing the
network-layer TTL/Hop Limit field.
When Relay ('R1') receives the Predirect message from Server ('S1')
it determines that Server ('S2') is the next hop toward Client ('C2')
by consulting its forwarding table. Relay ('R1') then re-
encapsulates the Predirect while changing the link-layer source
address to 'L2(R1)' and changing the link-layer destination address
to 'L2(S2)'. Relay ('R1') then relays the Predirect via Server
('S2').
When Server ('S2') receives the Predirect message from Relay ('R1')
it determines that Client ('C2') is a neighbor by consulting its
neighbor cache. Server ('S2') then re-encapsulates the Predirect
while changing the link-layer source address to 'L2(S2)' and changing
the link-layer destination address to 'L2(C2)'. Server ('S2') then
forwards the message to Client ('C2').
3.17.6. Processing Predirects and Sending Redirects
When Client ('C2') receives the Predirect message, it accepts the
Predirect only if the message has a link-layer source address of one
of its Servers (e.g., L2(S2)). Client ('C2') further accepts the
message only if it is willing to serve as a redirection target.
Next, Client ('C2') validates the message according to the ICMPv6
Templin Expires August 14, 2015 [Page 41]
Internet-Draft AERO February 2015
Redirect message validation rules in Section 8.1 of [RFC4861], except
that it accepts the message even though Code=1 and even though the
network-layer source address is not that of it's current first-hop
router.
In the reference operational scenario, when Client ('C2') receives a
valid Predirect message, it either creates or updates a dynamic
neighbor cache entry that stores the Target Address of the message as
the network-layer address of Client ('C1') , stores the link-layer
addresses found in the TLLAOs as the link-layer addresses of Client
('C1') and stores the Prefix Length as the length to be applied to
the network-layer address for forwarding purposes. Client ('C2')
then sets AcceptTime for the neighbor cache entry to ACCEPT_TIME.
After processing the message, Client ('C2') prepares a Redirect
message response as follows:
o the link-layer source address is set to 'L2(C2)' (i.e., the link-
layer address of Client ('C2')).
o the link-layer destination address is set to 'L2(S2)' (i.e., the
link-layer address of Server ('S2')).
o the network-layer source address is set to fe80::2001:db8:1:0
(i.e., the AERO address of Client ('C2')).
o the network-layer destination address is set to fe80::2001:db8:0:0
(i.e., the AERO address of Client ('C1')).
o the Type is set to 137.
o the Code is set to 0 to indicate "Redirect".
o the Prefix Length is set to the length of the prefix to be applied
to the Target Address.
o the Target Address is set to fe80::2001:db8:1:0 (i.e., the AERO
address of Client ('C2')).
o the Destination Address is set to the destination address of the
originating packet that triggered the Redirection event. (If the
originating packet is an IPv4 packet, the address is constructed
in IPv4-compatible IPv6 address format).
o the message includes one or more TLLAOs with Link ID and
Preference set to appropriate values for Client ('C2')'s
underlying interfaces, and with UDP Port Number and IP Address set
to '0'.
Templin Expires August 14, 2015 [Page 42]
Internet-Draft AERO February 2015
o the message SHOULD include a Timestamp option and MUST echo the
Nonce option received in the Predirect (i.e., if a Nonce option is
included).
o the message includes as much of the RHO copied from the
corresponding AERO Predirect message as possible such that at
least the network-layer header is included but the size of the
message does not exceed 1280 bytes.
After Client ('C2') prepares the Redirect message, it sends the
message to Server ('S2').
3.17.7. Re-encapsulating and Relaying Redirects
When Server ('S2') receives a Redirect message from Client ('C2'), it
first verifies that the TLLAOs in the Redirect are a proper subset of
the Link IDs in Client ('C2')'s neighbor cache entry. If the
Client's TLLAOs are not acceptable, Server ('S2') discards the
message. Otherwise, Server ('S2') validates the message according to
the ICMPv6 Redirect message validation rules in Section 8.1 of
[RFC4861]. Server ('S2') also verifies that Client ('C2') is
authorized to use the Prefix Length in the Redirect when applied to
the AERO address in the network-layer source address by searching for
the AERO address in the neighbor cache. If validation fails, Server
('S2') discards the Predirect; otherwise, it copies the correct UDP
Port numbers and IP Addresses for Client ('C2')'s links into the
(previously empty) TLLAOs.
Server ('S2') then examines the network-layer destination address of
the Predirect to determine the next hop toward Client ('C2') by
searching for the AERO address in the neighbor cache. Since Client
('C2') is not a neighbor, Server ('S2') re-encapsulates the Predirect
and relays it via Relay ('R1') by changing the link-layer source
address of the message to 'L2(S2)' and changing the link-layer
destination address to 'L2(R1)'. Server ('S2') finally forwards the
re-encapsulated message to Relay ('R1') without decrementing the
network-layer TTL/Hop Limit field.
When Relay ('R1') receives the Predirect message from Server ('S2')
it determines that Server ('S1') is the next hop toward Client ('C1')
by consulting its forwarding table. Relay ('R1') then re-
encapsulates the Predirect while changing the link-layer source
address to 'L2(R1)' and changing the link-layer destination address
to 'L2(S1)'. Relay ('R1') then relays the Predirect via Server
('S1').
When Server ('S1') receives the Predirect message from Relay ('R1')
it determines that Client ('C1') is a neighbor by consulting its
Templin Expires August 14, 2015 [Page 43]
Internet-Draft AERO February 2015
neighbor cache. Server ('S1') then re-encapsulates the Predirect
while changing the link-layer source address to 'L2(S1)' and changing
the link-layer destination address to 'L2(C1)'. Server ('S1') then
forwards the message to Client ('C1').
3.17.8. Processing Redirects
When Client ('C1') receives the Redirect message, it accepts the
message only if it has a link-layer source address of one of its
Servers (e.g., ''L2(S1)'). Next, Client ('C1') validates the message
according to the ICMPv6 Redirect message validation rules in
Section 8.1 of [RFC4861], except that it accepts the message even
though the network-layer source address is not that of it's current
first-hop router. Following validation, Client ('C1') then processes
the message as follows.
In the reference operational scenario, when Client ('C1') receives
the Redirect message, it either creates or updates a dynamic neighbor
cache entry that stores the Target Address of the message as the
network-layer address of Client ('C2'), stores the link-layer
addresses found in the TLLAOs as the link-layer addresses of Client
('C2') and stores the Prefix Length as the length to be applied to
the network-layer address for forwarding purposes. Client ('C1')
then sets ForwardTime for the neighbor cache entry to FORWARD_TIME.
Now, Client ('C1') has a neighbor cache entry with a valid
ForwardTime value, while Client ('C2') has a neighbor cache entry
with a valid AcceptTime value. Thereafter, Client ('C1') may forward
ordinary network-layer data packets directly to Client ('C2') without
involving any intermediate nodes, and Client ('C2') can verify that
the packets came from an acceptable source. (In order for Client
('C2') to forward packets to Client ('C1'), a corresponding
Predirect/Redirect message exchange is required in the reverse
direction; hence, the mechanism is asymmetric.)
3.17.9. Server-Oriented Redirection
In some environments, the Server nearest the target Client may need
to serve as the redirection target, e.g., if direct Client-to-Client
communications are not possible. In that case, the Server prepares
the Redirect message the same as if it were the destination Client
(see: Section 3.17.6), except that it writes its own link-layer
address in the TLLAO option. The Server must then maintain a dynamic
neighbor cache entry for the redirected source Client.
Templin Expires August 14, 2015 [Page 44]
Internet-Draft AERO February 2015
3.18. Neighbor Unreachability Detection (NUD)
AERO nodes perform Neighbor Unreachability Detection (NUD) by sending
unicast NS messages to elicit solicited NA messages from neighbors
the same as described in [RFC4861]. NUD is performed either
reactively in response to persistent L2 errors (see Section 3.14) or
proactively to refresh existing neighbor cache entries.
When an AERO node sends an NS/NA message, it MUST use its link-local
address as the IPv6 source address and the link-local address of the
neighbor as the IPv6 destination address. When an AERO node receives
an NS message or a solicited NA message, it accepts the message if it
has a neighbor cache entry for the neighbor; otherwise, it ignores
the message.
When a source Client is redirected to a target Client it SHOULD
proactively test the direct path by sending an initial NS message to
elicit a solicited NA response. While testing the path, the source
Client can optionally continue sending packets via the Server,
maintain a small queue of packets until target reachability is
confirmed, or (optimistically) allow packets to flow directly to the
target. The source Client SHOULD thereafter continue to proactively
test the direct path to the target Client (see Section 7.3 of
[RFC4861]) periodically in order to keep dynamic neighbor cache
entries alive.
In particular, while the source Client is actively sending packets to
the target Client it SHOULD also send NS messages separated by
RETRANS_TIMER milliseconds in order to receive solicited NA messages.
If the source Client is unable to elicit a solicited NA response from
the target Client after MAX_RETRY attempts, it SHOULD set ForwardTime
to 0 and resume sending packets via one of its Servers. Otherwise,
the source Client considers the path usable and SHOULD thereafter
process any link-layer errors as a hint that the direct path to the
target Client has either failed or has become intermittent.
When a target Client receives an NS message from a source Client, it
resets AcceptTime to ACCEPT_TIME if a neighbor cache entry exists;
otherwise, it discards the NS message. If ForwardTime is non-zero,
the target Client then sends a solicited NA message to the link-layer
address of the source Client; otherwise, it sends the solicited NA
message to the link-layer address of one of its Servers.
When a source Client receives a solicited NA message from a target
Client, it resets ForwardTime to FORWARD_TIME if a neighbor cache
entry exists; otherwise, it discards the NA message.
Templin Expires August 14, 2015 [Page 45]
Internet-Draft AERO February 2015
When ForwardTime for a dynamic neighbor cache entry expires, the
source Client resumes sending any subsequent packets via a Server and
may (eventually) attempt to re-initiate the AERO redirection process.
When AcceptTime for a dynamic neighbor cache entry expires, the
target Client discards any subsequent packets received directly from
the source Client. When both ForwardTime and AcceptTime for a
dynamic neighbor cache entry expire, the Client deletes the neighbor
cache entry.
3.19. Mobility Management
3.19.1. Announcing Link-Layer Address Changes
When a Client needs to change its link-layer address, e.g., due to a
mobility event, it performs an immediate DHCPv6 Rebind/Reply exchange
via each of its Servers using the new link-layer address as the
source and with a CLLAO that includes the correct Link ID and
Preference values. If authentication succeeds, the Server then
update its neighbor cache and sends a DHCPv6 Reply. Note that if the
Client does not issue a DHCPv6 Rebind before the prefix delegation
lifetime expires (e.g., if the Client has been out of touch with the
Server for a considerable amount of time), the Server's Reply will
report NoBinding and the Client must re-initiate the DHCPv6 PD
procedure.
Next, the Client sends unsolicited NA messages to each of its
correspondent Client neighbors using the same procedures as specified
in Section 7.2.6 of [RFC4861], except that it sends the messages as
unicast to each neighbor via a Server instead of multicast. In this
process, the Client should send no more than
MAX_NEIGHBOR_ADVERTISEMENT messages separated by no less than
RETRANS_TIMER seconds to each neighbor.
With reference to Figure 9, when Client ('C2') needs to change its
link-layer address it sends unicast unsolicited NA messages to Client
('C1') via Server ('S2') as follows:
o the link-layer source address is set to 'L2(C2)' (i.e., the link-
layer address of Client ('C2')).
o the link-layer destination address is set to 'L2(S2)' (i.e., the
link-layer address of Server ('S2')).
o the network-layer source address is set to fe80::2001:db8:1:0
(i.e., the AERO address of Client ('C2')).
o the network-layer destination address is set to fe80::2001:db8:0:0
(i.e., the AERO address of Client ('C1')).
Templin Expires August 14, 2015 [Page 46]
Internet-Draft AERO February 2015
o the Type is set to 136.
o the Code is set to 0.
o the Solicited flag is set to 0.
o the Override flag is set to 1.
o the Target Address is set to fe80::2001:db8:1:0 (i.e., the AERO
address of Client ('C2')).
o the message includes one or more TLLAOs with Link ID and
Preference set to appropriate values for Client ('C2')'s
underlying interfaces, and with UDP Port Number and IP Address set
to '0'.
o the message SHOULD include a Timestamp option.
When Server ('S1') receives the NA message, it relays the message in
the same way as described for relaying Redirect messages in
Section 3.17.7. In particular, Server ('S1') copies the correct UDP
port numbers and IP addresses into the TLLAOs, changes the link-layer
source address to its own address, changes the link-layer destination
address to the address of Relay ('R1'), then forwards the NA message
via the relaying chain the same as for a Redirect.
When Client ('C1') receives the NA message, it accepts the message
only if it already has a neighbor cache entry for Client ('C2') then
updates the link-layer addresses for Client ('C2') based on the
addresses in the TLLAOs. Next, Client ('C1') SHOULD initiate the NUD
procedures specified in Section 3.18 to provide Client ('C2') with an
indication that the link-layer source address has been updated, and
to refresh ('C2')'s AcceptTime and ('C1')'s ForwardTime timers.
If Client ('C2') receives an NS message from Client ('C1') indicating
that an unsolicited NA has updated its neighbor cache, Client ('C2')
need not send additional unsolicited NAs. If Client ('C2')'s
unsolicited NA messages are somehow lost, however, Client ('C1') will
soon learn of the mobility event via NUD.
3.19.2. Bringing New Links Into Service
When a Client needs to bring a new underlying interface into service
(e.g., when it activates a new data link), it performs an immediate
Rebind/Reply exchange via each of its Servers using the new link-
layer address as the source address and with a CLLAO that includes
the new Link ID and Preference values. If authentication succeeds,
the Server then updates its neighbor cache and sends a DHCPv6 Reply.
Templin Expires August 14, 2015 [Page 47]
Internet-Draft AERO February 2015
The Client MAY then send unsolicited NA messages to each of its
correspondent Clients to inform them of the new link-layer address as
described in Section 3.19.1.
3.19.3. Removing Existing Links from Service
When a Client needs to remove an existing underlying interface from
service (e.g., when it de-activates an existing data link), it
performs an immediate Rebind/Reply exchange via each of its Servers
over any available link with a CLLAO that includes the deprecated
Link ID and a Preference value of 0. If authentication succeeds, the
Server then updates its neighbor cache and sends a DHCPv6 Reply. The
Client SHOULD then send unsolicited NA messages to each of its
correspondent Clients to inform them of the deprecated link-layer
address as described in Section 3.19.1.
3.19.4. Moving to a New Server
When a Client associates with a new Server, it performs the Client
procedures specified in Section 3.15.2.
When a Client disassociates with an existing Server, it sends a
DHCPv6 Release message via a new Server to the unicast link-local
network layer address of the old Server. The new Server then writes
its own link-layer address in the DHCPv6 Release message IP source
address and forwards the message to the old Server.
When the old Server receives the DHCPv6 Release, it first
authenticates the message. The Server then resets the Client's
neighbor cache entry lifetime to 5 seconds, rewrites the link-layer
address in the neighbor cache entry to the address of the new Server,
then returns a DHCPv6 Reply message to the Client via the old Server.
When the lifetime expires, the old Server withdraws the IP route from
the AERO routing system and deletes the neighbor cache entry for the
Client. The Client can then use the Reply message to verify that the
termination signal has been processed, and can delete both the
default route and the neighbor cache entry for the old Server. (Note
that since Release/Reply messages may be lost in the network the
Client MUST retry until it gets Reply indicating that the Release was
successful.)
Clients SHOULD NOT move rapidly between Servers in order to avoid
causing excessive oscillations in the AERO routing system. Such
oscillations could result in intermittent reachability for the Client
itself, while causing little harm to the network. Examples of when a
Client might wish to change to a different Server include a Server
that has gone unreachable, topological movements of significant
distance, etc.
Templin Expires August 14, 2015 [Page 48]
Internet-Draft AERO February 2015
3.20. Proxy AERO
Proxy Mobile IPv6 (PMIPv6) [RFC5213][RFC5844][RFC5949] presents a
localized mobility management scheme for use within an access network
domain. It is typically used in WiFi and cellular wireless access
networks, and allows Mobile Nodes (MNs) to receive and retain an IP
address that remains stable within the access network domain without
needing to implement any special mobility protocols. In the PMIPv6
architecture, access network devices known as Mobility Access
Gateways (MAGs) provide MNs with an access link abstraction and
receive prefixes for the MNs from a Local Mobility Anchor (LMA).
In a proxy AERO domain, a proxy AERO Client (acting as a MAG) can
similarly provide proxy services for MNs that do not participate in
AERO messaging. The proxy Client presents an access link abstraction
to MNs, and performs DHCPv6 PD exchanges over the AERO interface with
an AERO Server (acting as an LMA) to receive ACPs for address
provisioning of new MNs that come onto an access link. This scheme
assumes that proxy Clients act as fixed (non-mobile) infrastructure
elements under the same administrative trust basis as for Relays and
Servers.
When an MN comes onto an access link within a proxy AERO domain for
the first time, the proxy Client authenticates the MN and obtains a
unique identifier that it can use as a DHCPv6 DUID then issues a
DHCPv6 PD Request to its Server. When the Server delegates an ACP,
the proxy Client creates an AERO address for the MN and assigns the
ACP to the MN's access link. The proxy Client then configures itself
as a default router for the MN and provides address autoconfiguration
services (e.g., SLAAC, DHCPv6, DHCPv4, etc.) for provisioning MN
addresses from the ACP over the access link. Since the proxy Client
may serve many such MNs simultaneously, it may receive multiple ACP
prefix delegations and configure multiple AERO addresses, i.e., one
for each MN.
When two MNs are associated with the same proxy Client, the Client
can forward traffic between the MNs without involving a Server since
it configures the AERO addresses of both MNs and therefore also has
the necessary routing information. When two MNs are associated with
different proxy Clients, the source MN's Client can initiate standard
AERO route optimization to discover a direct path to the target MN's
Client through the exchange of Predirect/Redirect messages.
When an MN in a proxy AERO domain leaves an access link provided by
an old proxy Client, the MN issues an access link-specific "leave"
message that informs the old Client of the link-layer address of a
new Client on the planned new access link. This is known as a
"predictive handover". When an MN comes onto an access link provided
Templin Expires August 14, 2015 [Page 49]
Internet-Draft AERO February 2015
by a new proxy Client, the MN issues an access link-specific "join"
message that informs the new Client of the link-layer address of the
old Client on the actual old access link. This is known as a
"reactive handover".
Upon receiving a predictive handover indication, the old proxy Client
sends a DHCPv6 PD Request message directly to the new Client and
queues any arriving data packets addressed to the departed MN. The
Request message includes the MN's ID as the DUID, the ACP in an IA_PD
option, the AERO address derived from the MN's ACP as the network-
layer source address, 'All_DHCP_Relay_Agents_and_Servers' as the
network-layer destination address, the old Client's address as the
link-layer source address and the new Client's address as the link-
layer destination address. When the new Client receives the Request
message, it changes the link-layer source address to its own address,
changes the link-layer destination address to the address of its
Server, and forwards the message to the Server. At the same time,
the new Client creates access link state for the ACP in anticipation
of the MN's arrival (while queuing any data packets until the MN
arrives), creates a neighbor cache entry for the old Client with
AcceptTime set to ACCEPT_TIME, then sends a Redirect message back to
the old Client. When the old Client receives the Redirect message,
it creates a neighbor cache entry for new Client with ForwardTime set
to FORWARD_TIME, then forwards any queued data packets to the new
Client. At the same time, the old Client sends a DHCPv6 PD Release
message to its Server. Finally, the old Client sends unsolicited NA
messages to any of the ACP's correspondents with a TLLAO containing
the link-layer address of the new Client. This follows the procedure
specified in Section 3.19.1, except that it is the old Client and not
the Server that supplies the link-layer address.
Upon receiving a reactive handover indication, the new proxy Client
creates access link state for the MN's ACP, sends a DHCPv6 PD Request
message to its Server, and sends a DHCPv6 PD Release message directly
to the old Client. The Release message includes the MN's ID as the
DUID, the ACP in an IA_PD option, the AERO address derived from the
MN's ACP as the network-layer source address,
'All_DHCP_Relay_Agents_and_Servers' as the network-layer destination
address, the new Client's address as the link-layer source address
and the old Client's address as the link-layer destination address.
When the old Client receives the Release message, it changes the
link-layer source address to its own address, changes the link-layer
destination address to the address of its Server, and forwards the
message to the Server. At the same time, the old Client sends a
Predirect message back to the new Client and queues any arriving data
packets addressed to the departed MN. When the new Client receives
the Predirect, it creates a neighbor cache entry for the old Client
with AcceptTime set to ACCEPT_TIME, then sends a Redirect message
Templin Expires August 14, 2015 [Page 50]
Internet-Draft AERO February 2015
back to the old Client. When the old Client receives the Redirect
message, it creates a neighbor cache entry for the new Client with
ForwardTime set to FORWARD_TIME, then forwards any queued data
packets to the new Client. Finally, the old Client sends unsolicited
NA messages to correspondents the same as for the predictive case.
When a Server processes a DHCPv6 Request message, it creates a
neighbor cache entry for this ACP if none currently exists. If a
neighbor cache entry already exists, however, the Server changes the
link-layer address to the address of the new proxy Client (this
satisfies the case of both the old Client and new Client using the
same Server).
When a Server processes a DHCPv6 Release message, it resets the
neighbor cache entry lifetime for this ACP to 5 seconds if the cached
link-layer address matches the old proxy Client's address.
Otherwise, the Server ignores the Release message (this satisfies the
case of both the old Client and new Client using the same Server).
When a correspondent Client receives an unsolicited NA message, it
changes the link-layer address for the ACP's neighbor cache entry to
the address of the new proxy Client. The correspondent Client then
issues a Predirect/Redirect exchange to establish a new neighbor
cache entry in the new Client.
From an architectural perspective, in addition to the use of DHCPv6
PD and IPv6 ND signaling the AERO approach differs from PMIPv6 in its
use of the NBMA virtual link model instead of point-to-point tunnels.
This provides a more agile interface for Client/Server and Client/
Client coordinations, and also facilitates simple route optimization.
The AERO routing system is also arranged in such a fashion that
Clients get the same service from any Server they happen to associate
with. This provides a natural fault tolerance and load balancing
capability such as desired for distributed mobility management.
3.21. Extending AERO Links Through Security Gateways
When an enterprise mobile device moves from a campus LAN connection
to a public Internet link, it must re-enter the enterprise via a
security gateway that has both a physical interface connection to the
Internet and a physical interface connection to the enterprise
internetwork. This most often entails the establishment of a Virtual
Private Network (VPN) link over the public Internet from the mobile
device to the security gateway. During this process, the mobile
device supplies the security gateway with its public Internet address
as the link-layer address for the VPN. The mobile device then acts
as an AERO Client to negotiate with the security gateway to obtain
its ACP.
Templin Expires August 14, 2015 [Page 51]
Internet-Draft AERO February 2015
In order to satisfy this need, the security gateway also operates as
an AERO Server with support for AERO Client proxying. In particular,
when a mobile device (i.e., the Client) connects via the security
gateway (i.e., the Server), the Server provides the Client with an
ACP in a DHCPv6 PD exchange the same as if it were attached to an
enterprise campus access link. The Server then replaces the Client's
link-layer source address with the Server's enterprise-facing link-
layer address in all AERO messages the Client sends toward neighbors
on the AERO link. The AERO messages are then delivered to other
devices on the AERO link as if they were originated by the security
gateway instead of by the AERO Client. In the reverse direction, the
AERO messages sourced by devices within the enterprise network can be
forwarded to the security gateway, which then replaces the link-layer
destination address with the Client's link-layer address and replaces
the link-layer source address with its own (Internet-facing) link-
layer address.
After receiving the ACP, the Client can send IP packets that use an
address taken from the ACP as the network layer source address, the
Client's link-layer address as the link-layer source address, and the
Server's Internet-facing link-layer address as the link-layer
destination address. The Server will then rewrite the link-layer
source address with the Server's own enterprise-facing link-layer
address and rewrite the link-layer destination address with the
target AERO node's link-layer address, and the packets will enter the
enterprise network as though they were sourced from a device located
within the enterprise. In the reverse direction, when a packet
sourced by a node within the enterprise network uses a destination
address from the Client's ACP, the packet will be delivered to the
security gateway which then rewrites the link-layer destination
address to the Client's link-layer address and rewrites the link-
layer source address to the Server's Internet-facing link-layer
address. The Server then delivers the packet across the VPN to the
AERO Client. In this way, the AERO virtual link is essentially
extended *through* the security gateway to the point at which the VPN
link and AERO link are effectively grafted together by the link-layer
address rewriting performed by the security gateway. All AERO
messaging services (including route optimization and mobility
signaling) are therefore extended to the Client.
In order to support this virtual link grafting, the security gateway
(acting as an AERO Server) must keep static neighbor cache entries
for all of its associated Clients located on the public Internet.
The neighbor cache entry is keyed by the AERO Client's AERO address
the same as if the Client were located within the enterprise
internetwork. The neighbor cache is then managed in all ways as
though the Client were an ordinary AERO Client. This includes the
Templin Expires August 14, 2015 [Page 52]
Internet-Draft AERO February 2015
AERO IPv6 ND messaging signaling for Route Optimization and Neighbor
Unreachability Detection.
Note that the main difference between a security gateway acting as an
AERO Server and an enterprise-internal AERO Server is that the
security gateway has at least one enterprise-internal physical
interface and at least one public Internet physical interface.
Conversely, the enterprise-internal AERO Server has only enterprise-
internal physical interfaces. For this reason security gateway
proxying is needed to ensure that the public Internet link-layer
addressing space is kept separate from the enterprise-internal link-
layer addressing space. This is afforded through a natural extension
of the security association caching already performed for each VPN
client by the security gateway.
3.22. Extending IPv6 AERO Links to the Internet
When an IPv6 host ('H1') with an address from an ACP owned by AERO
Client ('C1') sends packets to a correspondent IPv6 host ('H2'), the
packets eventually arrive at the IPv6 router that owns ('H2')s
prefix. This IPv6 router may or may not be an AERO Client ('C2')
either within the same home network as ('C1') or in a different home
network.
If Client ('C1') is currently located outside the boundaries of its
home network, it will connect back into the home network via a
security gateway acting as an AERO Server. The packets sent by
('H1') via ('C1') will then be forwarded through the security gateway
then through the home network and finally to ('C2') where they will
be delivered to ('H2'). This could lead to sub-optimal performance
when ('C2') could instead be reached via a more direct route without
involving the security gateway.
Consider the case when host ('H1') has the IPv6 address
2001:db8:1::1, and Client ('C1') has the ACP 2001:db8:1::/64 with
underlying IPv6 Internet address of 2001:db8:1000::1. Also, host
('H2') has the IPv6 address 2001:db8:2::1, and Client ('C2') has the
ACP 2001:db8:2::/64 with underlying IPv6 address of 2001:db8:2000::1.
Client ('C1') can determine whether 'C2' is indeed also an AERO
Client willing to serve as a route optimization correspondent by
resolving the AAAA records for the DNS FQDN that matches ('H2')s
prefix, i.e.:
'0.0.0.0.2.0.0.0.8.b.d.0.1.0.0.2.aero.linkupnetworks.net'
If ('C2') is indeed a candidate correspondent, the FQDN lookup will
return a PTR resource record that contains the domain name for the
AERO link that manages ('C2')s ASP. Client ('C1') can then attempt
Templin Expires August 14, 2015 [Page 53]
Internet-Draft AERO February 2015
route optimization using an approach similar to the Return
Routability procedure specified for Mobile IPv6 (MIPv6) [RFC6275].
In order to support this process, both Clients MUST intercept and
decapsulate packets that have a subnet router anycast address
corresponding to any of the /64 prefixes covered by their respective
ACPs.
To initiate the process, Client ('C1') creates a specially-crafted
encapsulated AERO Predirect message that will be routed through its
home network then through ('C2')s home network and finally to ('C2')
itself. Client ('C1') prepares the initial message in the exchange
as follows:
o The encapsulating IPv6 header source address is set to
2001:db8:1:: (i.e., the IPv6 subnet router anycast address for
('C1')s ACP)
o The encapsulating IPv6 header destination address is set to
2001:db8:2:: (i.e., the IPv6 subnet router anycast address for
('C2')s ACP)
o The encapsulating IPv6 header is followed by a UDP header with
source and destination port set to 8060
o The encapsulated IPv6 header source address is set to
fe80::2001:db8:1:0 (i.e., the AERO address for ('C1'))
o The encapsulated IPv6 header destination address is set to
fe80::2001:db8:2:0 (i.e., the AERO address for ('C2'))
o The encapsulated AERO Predirect message includes all of the
securing information that would occur in a MIPv6 "Home Test Init"
message (format TBD)
Client ('C1') then further encapsulates the message in the
encapsulating headers necessary to convey the packet to the security
gateway (e.g., through IPsec encapsulation) so that the message now
appears "double-encapsulated". ('C1') then sends the message to the
security gateway, which re-encapsulates and forwards it over the home
network from where it will eventually reach ('C2').
At the same time, ('C1') creates and sends a second encapsulated AERO
Predirect message that will be routed through the IPv6 Internet
without involving the security gateway. Client ('C1') prepares the
message as follows:
o The encapsulating IPv6 header source address is set to
2001:db8:1000:1 (i.e., the Internet IPv6 address of ('C1'))
Templin Expires August 14, 2015 [Page 54]
Internet-Draft AERO February 2015
o The encapsulating IPv6 header destination address is set to
2001:db8:2:: (i.e., the IPv6 subnet router anycast address for
('C2')s ACP)
o The encapsulating IPv6 header is followed by a UDP header with
source and destination port set to 8060
o The encapsulated IPv6 header source address is set to
fe80::2001:db8:1:0 (i.e., the AERO address for ('C1'))
o The encapsulated IPv6 header destination address is set to
fe80::2001:db8:2:0 (i.e., the AERO address for ('C2'))
o The encapsulated AERO Predirect message includes all of the
securing information that would occur in a MIPv6 "Care-of Test
Init" message (format TBD)
('C2') will receive both Predirect messages through its home network
then return a corresponding Redirect for each of the Predirect
messages with the source and destination addresses in the inner and
outer headers reversed. The first message includes all of the
securing information that would occur in a MIPv6 "Home Test" message,
while the second message includes all of the securing information
that would occur in a MIPv6 "Care-of Test" message (formats TBD).
When ('C1') receives the Redirect messages, it performs the necessary
security procedures per the MIPv6 specification. It then prepares an
encapsulated NS message that includes the same source and destination
addresses as for the "Care-of Test Init" Predirect message, and
includes all of the securing information that would occur in a MIPv6
"Binding Update" message (format TBD) and sends the message to
('C2').
When ('C2') receives the NS message, if the securing information is
correct it creates or updates a neighbor cache entry for ('C1') with
fe80::2001:db8:1:0 as the network-layer address, 2001:db8:1000::1 as
the link-layer address and with AcceptTime set to ACCEPT_TIME.
('C2') then sends an encapsulated NA message back to ('C1') that
includes the same source and destination addresses as for the "Care-
of Test" Redirect message, and includes all of the securing
information that would occur in a MIPv6 "Binding Acknowledgement"
message (format TBD) and sends the message to ('C1').
When ('C1') receives the NA message, it creates or updates a neighbor
cache entry for ('C2') with fe80::2001:db8:2:0 as the network-layer
address and 2001:db8:2:: as the link-layer address and with
ForwardTime set to FORWARD_TIME, thus completing the route
optimization in the forward direction.
Templin Expires August 14, 2015 [Page 55]
Internet-Draft AERO February 2015
('C1') subsequently forwards encapsulated packets with outer source
address 2001:db8:1000::1, with outer destination address
2001:db8:2::, with inner source address taken from the 2001:db8:1::,
and with inner destination address taken from 2001:db8:2:: due to the
fact that it has a securely-established neighbor cache entry with
non-zero ForwardTime. ('C2') subsequently accepts any such
encapsulated packets due to the fact that it has a securely-
established neighbor cache entry with non-zero AcceptTime.
In order to keep neighbor cache entries alive, ('C1') periodically
sends additional NS messages to ('C2') and receives any NA responses.
If ('C1') moves to a different point of attachment after the initial
route optimization, it sends a new secured NS message to ('C2') as
above to update ('C2')s neighbor cache.
If ('C2') has packets to send to ('C1'), it performs a corresponding
route optimization in the opposite direction following the same
procedures described above. In the process, the already-established
unidirectional neighbor cache entries within ('C1') and ('C2') are
updated to include the now-bidirectional information. In particular,
the AcceptTime and ForwardTime variables for both neighbor cache
entries are updated to non-zero values, and the link-layer address
for ('C1')s neighbor cache entry for ('C2') is reset to
2001:db8:2000::1.
Note that two AERO Clients can use full security protocol messaging
instead of Return Routability, e.g., if strong authentication and/or
confidentiality are desired. In that case, security protocol key
exchanges such as specified for MOBIKE [RFC4555] would be used to
establish security associations and neighbor cache entries between
the AERO clients. Thereafter, AERO NS/NA messaging can be used to
maintain neighbor cache entries, test reachability, and to announce
mobility events. If reachability testing fails, e.g., if both
Clients move at roughly the same time, the Clients can tear down the
security association and neighbor cache entries and again allow
packets to flow through their home network.
3.23. Encapsulation Protocol Version Considerations
A source Client may connect only to an IPvX underlying network, while
the target Client connects only to an IPvY underlying network. In
that case, the target and source Clients have no means for reaching
each other directly (since they connect to underlying networks of
different IP protocol versions) and so must ignore any redirection
messages and continue to send packets via the Server.
Templin Expires August 14, 2015 [Page 56]
Internet-Draft AERO February 2015
3.24. Multicast Considerations
When the underlying network does not support multicast, AERO nodes
map IPv6 link-scoped multicast addresses (including
'All_DHCP_Relay_Agents_and_Servers') to the link-layer address of a
Server.
When the underlying network supports multicast, AERO nodes use the
multicast address mapping specification found in [RFC2529] for IPv4
underlying networks and use a direct multicast mapping for IPv6
underlying networks. (In the latter case, "direct multicast mapping"
means that if the IPv6 multicast destination address of the
encapsulated packet is "M", then the IPv6 multicast destination
address of the encapsulating header is also "M".)
3.25. Operation on AERO Links Without DHCPv6 Services
When Servers on the AERO link do not provide DHCPv6 services,
operation can still be accommodated through administrative
configuration of ACPs on AERO Clients. In that case, administrative
configurations of AERO interface neighbor cache entries on both the
Server and Client are also necessary. However, this may interfere
with the ability for Clients to dynamically change to new Servers,
and can expose the AERO link to misconfigurations unless the
administrative configurations are carefully coordinated.
3.26. Operation on Server-less AERO Links
In some AERO link scenarios, there may be no Servers on the link and/
or no need for Clients to use a Server as an intermediary trust
anchor. In that case, each Client acts as a Server unto itself to
establish neighbor cache entries by performing direct Client-to-
Client IPv6 ND message exchanges, and some other form of trust basis
must be applied so that each Client can verify that the prospective
neighbor is authorized to use its claimed ACP.
When there is no Server on the link, Clients must arrange to receive
ACPs and publish them via a secure alternate prefix delegation
authority through some means outside the scope of this document.
3.27. Manually-Configured AERO Tunnels
In addition to the dynamic neighbor discovery procedures for AERO
link neighbors described above, AERO encapsulation can be applied to
manually-configured tunnels. In that case, the tunnel endpoints use
an administratively-assigned link-local address and exchange NS/NA
messages the same as for dynamically-established tunnels.
Templin Expires August 14, 2015 [Page 57]
Internet-Draft AERO February 2015
3.28. Intradomain Routing
After a tunnel neighbor relationship has been established, neighbors
can use a traditional dynamic routing protocol over the tunnel to
exchange routing information without having to inject the routes into
the AERO routing system.
4. Implementation Status
An application-layer implementation is in progress.
5. IANA Considerations
IANA has assign a 4-octet Private Enterprise Number "45282" for AERO
in the "enterprise-numbers" registry. No further IANA actions are
required.
6. Security Considerations
AERO link security considerations are the same as for standard IPv6
Neighbor Discovery [RFC4861] except that AERO improves on some
aspects. In particular, AERO uses a trust basis between Clients and
Servers, where the Clients only engage in the AERO mechanism when it
is facilitated by a trust anchor. Unless there is some other means
of authenticating the Client's identity (e.g., link-layer security),
AERO nodes SHOULD also use DHCPv6 securing services (e.g., DHCPv6
authentication, Secure DHCPv6 [I-D.ietf-dhc-sedhcpv6], etc.) for
Client authentication and network admission control.
AERO Redirect, Predirect and unsolicited NA messages SHOULD include a
Timestamp option (see Section 5.3 of [RFC3971]) that other AERO nodes
can use to verify the message time of origin. AERO Predirect, NS and
RS messages SHOULD include a Nonce option (see Section 5.3 of
[RFC3971]) that recipients echo back in corresponding responses.
AERO links must be protected against link-layer address spoofing
attacks in which an attacker on the link pretends to be a trusted
neighbor. Links that provide link-layer securing mechanisms (e.g.,
IEEE 802.1X WLANs) and links that provide physical security (e.g.,
enterprise network wired LANs) provide a first line of defense that
is often sufficient. In other instances, additional securing
mechanisms such as Secure Neighbor Discovery (SeND) [RFC3971], IPsec
[RFC4301] or TLS [RFC5246] may be necessary.
AERO Clients MUST ensure that their connectivity is not used by
unauthorized nodes on their EUNs to gain access to a protected
network, i.e., AERO Clients that act as routers MUST NOT provide
routing services for unauthorized nodes. (This concern is no
Templin Expires August 14, 2015 [Page 58]
Internet-Draft AERO February 2015
different than for ordinary hosts that receive an IP address
delegation but then "share" the address with unauthorized nodes via a
NAT function.)
On some AERO links, establishment and maintenance of a direct path
between neighbors requires secured coordination such as through the
Internet Key Exchange (IKEv2) protocol [RFC5996] to establish a
security association.
An AERO Client's link-layer address could be rewritten by a link-
layer switching element on the path from the Client to the Server and
not detected by the DHCPv6 security mechanism. However, such a
condition would only be a matter of concern on unmanaged/unsecured
links where the link-layer switching elements themselves present a
man-in-the-middle attack threat. For this reason, IP security MUST
be used when AERO is employed over unmanaged/unsecured links.
7. Acknowledgements
Discussions both on IETF lists and in private exchanges helped shape
some of the concepts in this work. Individuals who contributed
insights include Mikael Abrahamsson, Mark Andrews, Fred Baker,
Stewart Bryant, Brian Carpenter, Wojciech Dec, Ralph Droms, Adrian
Farrel, Sri Gundavelli, Brian Haberman, Joel Halpern, Tom Herbert,
Sascha Hlusiak, Lee Howard, Andre Kostur, Ted Lemon, Andy Malis,
Satoru Matsushima, Tomek Mrugalski, Behcet Saikaya, Joe Touch, Bernie
Volz, Ryuji Wakikawa and Lloyd Wood. Members of the IESG also
provided valuable input during their review process that greatly
improved the document. Special thanks go to Stewart Bryant, Joel
Halpern and Brian Haberman for their shepherding guidance.
This work has further been encouraged and supported by Boeing
colleagues including Keith Bartley, Dave Bernhardt, Cam Brodie,
Balaguruna Chidambaram, Bruce Cornish, Claudiu Danilov, Wen Fang,
Anthony Gregory, Jeff Holland, Ed King, Gen MacLean, Rob Muszkiewicz,
Sean O'Sullivan, Kent Shuey, Brian Skeen, Mike Slane, Brendan
Williams, Julie Wulff, Yueli Yang, and other members of the BR&T and
BIT mobile networking teams.
Earlier works on NBMA tunneling approaches are found in
[RFC2529][RFC5214][RFC5569].
Many of the constructs presented in this second edition of AERO are
based on the author's earlier works, including:
o The Internet Routing Overlay Network (IRON)
[RFC6179][I-D.templin-ironbis]
Templin Expires August 14, 2015 [Page 59]
Internet-Draft AERO February 2015
o Virtual Enterprise Traversal (VET)
[RFC5558][I-D.templin-intarea-vet]
o The Subnetwork Encapsulation and Adaptation Layer (SEAL)
[RFC5320][I-D.templin-intarea-seal]
o AERO, First Edition [RFC6706]
Note that these works cite numerous earlier efforts that are not also
cited here due to space limitations. The authors of those earlier
works are acknowledged for their insights.
8. References
8.1. Normative References
[RFC0768] Postel, J., "User Datagram Protocol", STD 6, RFC 768,
August 1980.
[RFC0791] Postel, J., "Internet Protocol", STD 5, RFC 791, September
1981.
[RFC0792] Postel, J., "Internet Control Message Protocol", STD 5,
RFC 792, September 1981.
[RFC2003] Perkins, C., "IP Encapsulation within IP", RFC 2003,
October 1996.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2460] Deering, S. and R. Hinden, "Internet Protocol, Version 6
(IPv6) Specification", RFC 2460, December 1998.
[RFC2473] Conta, A. and S. Deering, "Generic Packet Tunneling in
IPv6 Specification", RFC 2473, December 1998.
[RFC3315] Droms, R., Bound, J., Volz, B., Lemon, T., Perkins, C.,
and M. Carney, "Dynamic Host Configuration Protocol for
IPv6 (DHCPv6)", RFC 3315, July 2003.
[RFC3633] Troan, O. and R. Droms, "IPv6 Prefix Options for Dynamic
Host Configuration Protocol (DHCP) version 6", RFC 3633,
December 2003.
[RFC3971] Arkko, J., Kempf, J., Zill, B., and P. Nikander, "SEcure
Neighbor Discovery (SEND)", RFC 3971, March 2005.
Templin Expires August 14, 2015 [Page 60]
Internet-Draft AERO February 2015
[RFC4213] Nordmark, E. and R. Gilligan, "Basic Transition Mechanisms
for IPv6 Hosts and Routers", RFC 4213, October 2005.
[RFC4861] Narten, T., Nordmark, E., Simpson, W., and H. Soliman,
"Neighbor Discovery for IP version 6 (IPv6)", RFC 4861,
September 2007.
[RFC4862] Thomson, S., Narten, T., and T. Jinmei, "IPv6 Stateless
Address Autoconfiguration", RFC 4862, September 2007.
[RFC6434] Jankiewicz, E., Loughney, J., and T. Narten, "IPv6 Node
Requirements", RFC 6434, December 2011.
8.2. Informative References
[I-D.ietf-dhc-sedhcpv6]
Jiang, S., Shen, S., Zhang, D., and T. Jinmei, "Secure
DHCPv6", draft-ietf-dhc-sedhcpv6-05 (work in progress),
December 2014.
[I-D.templin-intarea-seal]
Templin, F., "The Subnetwork Encapsulation and Adaptation
Layer (SEAL)", draft-templin-intarea-seal-68 (work in
progress), January 2014.
[I-D.templin-intarea-vet]
Templin, F., "Virtual Enterprise Traversal (VET)", draft-
templin-intarea-vet-40 (work in progress), May 2013.
[I-D.templin-ironbis]
Templin, F., "The Interior Routing Overlay Network
(IRON)", draft-templin-ironbis-16 (work in progress),
March 2014.
[I-D.vandevelde-idr-remote-next-hop]
Velde, G., Patel, K., Rao, D., Raszuk, R., and R. Bush,
"BGP Remote-Next-Hop", draft-vandevelde-idr-remote-next-
hop-08 (work in progress), October 2014.
[RFC0879] Postel, J., "TCP maximum segment size and related topics",
RFC 879, November 1983.
[RFC1035] Mockapetris, P., "Domain names - implementation and
specification", STD 13, RFC 1035, November 1987.
[RFC1191] Mogul, J. and S. Deering, "Path MTU discovery", RFC 1191,
November 1990.
Templin Expires August 14, 2015 [Page 61]
Internet-Draft AERO February 2015
[RFC1812] Baker, F., "Requirements for IP Version 4 Routers", RFC
1812, June 1995.
[RFC1930] Hawkinson, J. and T. Bates, "Guidelines for creation,
selection, and registration of an Autonomous System (AS)",
BCP 6, RFC 1930, March 1996.
[RFC1981] McCann, J., Deering, S., and J. Mogul, "Path MTU Discovery
for IP version 6", RFC 1981, August 1996.
[RFC2131] Droms, R., "Dynamic Host Configuration Protocol", RFC
2131, March 1997.
[RFC2529] Carpenter, B. and C. Jung, "Transmission of IPv6 over IPv4
Domains without Explicit Tunnels", RFC 2529, March 1999.
[RFC2675] Borman, D., Deering, S., and R. Hinden, "IPv6 Jumbograms",
RFC 2675, August 1999.
[RFC2764] Gleeson, B., Heinanen, J., Lin, A., Armitage, G., and A.
Malis, "A Framework for IP Based Virtual Private
Networks", RFC 2764, February 2000.
[RFC2784] Farinacci, D., Li, T., Hanks, S., Meyer, D., and P.
Traina, "Generic Routing Encapsulation (GRE)", RFC 2784,
March 2000.
[RFC2923] Lahey, K., "TCP Problems with Path MTU Discovery", RFC
2923, September 2000.
[RFC2983] Black, D., "Differentiated Services and Tunnels", RFC
2983, October 2000.
[RFC3168] Ramakrishnan, K., Floyd, S., and D. Black, "The Addition
of Explicit Congestion Notification (ECN) to IP", RFC
3168, September 2001.
[RFC3596] Thomson, S., Huitema, C., Ksinant, V., and M. Souissi,
"DNS Extensions to Support IP Version 6", RFC 3596,
October 2003.
[RFC3819] Karn, P., Bormann, C., Fairhurst, G., Grossman, D.,
Ludwig, R., Mahdavi, J., Montenegro, G., Touch, J., and L.
Wood, "Advice for Internet Subnetwork Designers", BCP 89,
RFC 3819, July 2004.
[RFC4271] Rekhter, Y., Li, T., and S. Hares, "A Border Gateway
Protocol 4 (BGP-4)", RFC 4271, January 2006.
Templin Expires August 14, 2015 [Page 62]
Internet-Draft AERO February 2015
[RFC4291] Hinden, R. and S. Deering, "IP Version 6 Addressing
Architecture", RFC 4291, February 2006.
[RFC4301] Kent, S. and K. Seo, "Security Architecture for the
Internet Protocol", RFC 4301, December 2005.
[RFC4443] Conta, A., Deering, S., and M. Gupta, "Internet Control
Message Protocol (ICMPv6) for the Internet Protocol
Version 6 (IPv6) Specification", RFC 4443, March 2006.
[RFC4511] Sermersheim, J., "Lightweight Directory Access Protocol
(LDAP): The Protocol", RFC 4511, June 2006.
[RFC4555] Eronen, P., "IKEv2 Mobility and Multihoming Protocol
(MOBIKE)", RFC 4555, June 2006.
[RFC4592] Lewis, E., "The Role of Wildcards in the Domain Name
System", RFC 4592, July 2006.
[RFC4821] Mathis, M. and J. Heffner, "Packetization Layer Path MTU
Discovery", RFC 4821, March 2007.
[RFC4963] Heffner, J., Mathis, M., and B. Chandler, "IPv4 Reassembly
Errors at High Data Rates", RFC 4963, July 2007.
[RFC4994] Zeng, S., Volz, B., Kinnear, K., and J. Brzozowski,
"DHCPv6 Relay Agent Echo Request Option", RFC 4994,
September 2007.
[RFC5213] Gundavelli, S., Leung, K., Devarapalli, V., Chowdhury, K.,
and B. Patil, "Proxy Mobile IPv6", RFC 5213, August 2008.
[RFC5214] Templin, F., Gleeson, T., and D. Thaler, "Intra-Site
Automatic Tunnel Addressing Protocol (ISATAP)", RFC 5214,
March 2008.
[RFC5246] Dierks, T. and E. Rescorla, "The Transport Layer Security
(TLS) Protocol Version 1.2", RFC 5246, August 2008.
[RFC5320] Templin, F., "The Subnetwork Encapsulation and Adaptation
Layer (SEAL)", RFC 5320, February 2010.
[RFC5494] Arkko, J. and C. Pignataro, "IANA Allocation Guidelines
for the Address Resolution Protocol (ARP)", RFC 5494,
April 2009.
Templin Expires August 14, 2015 [Page 63]
Internet-Draft AERO February 2015
[RFC5522] Eddy, W., Ivancic, W., and T. Davis, "Network Mobility
Route Optimization Requirements for Operational Use in
Aeronautics and Space Exploration Mobile Networks", RFC
5522, October 2009.
[RFC5558] Templin, F., "Virtual Enterprise Traversal (VET)", RFC
5558, February 2010.
[RFC5569] Despres, R., "IPv6 Rapid Deployment on IPv4
Infrastructures (6rd)", RFC 5569, January 2010.
[RFC5720] Templin, F., "Routing and Addressing in Networks with
Global Enterprise Recursion (RANGER)", RFC 5720, February
2010.
[RFC5844] Wakikawa, R. and S. Gundavelli, "IPv4 Support for Proxy
Mobile IPv6", RFC 5844, May 2010.
[RFC5949] Yokota, H., Chowdhury, K., Koodli, R., Patil, B., and F.
Xia, "Fast Handovers for Proxy Mobile IPv6", RFC 5949,
September 2010.
[RFC5996] Kaufman, C., Hoffman, P., Nir, Y., and P. Eronen,
"Internet Key Exchange Protocol Version 2 (IKEv2)", RFC
5996, September 2010.
[RFC6146] Bagnulo, M., Matthews, P., and I. van Beijnum, "Stateful
NAT64: Network Address and Protocol Translation from IPv6
Clients to IPv4 Servers", RFC 6146, April 2011.
[RFC6179] Templin, F., "The Internet Routing Overlay Network
(IRON)", RFC 6179, March 2011.
[RFC6204] Singh, H., Beebee, W., Donley, C., Stark, B., and O.
Troan, "Basic Requirements for IPv6 Customer Edge
Routers", RFC 6204, April 2011.
[RFC6221] Miles, D., Ooghe, S., Dec, W., Krishnan, S., and A.
Kavanagh, "Lightweight DHCPv6 Relay Agent", RFC 6221, May
2011.
[RFC6241] Enns, R., Bjorklund, M., Schoenwaelder, J., and A.
Bierman, "Network Configuration Protocol (NETCONF)", RFC
6241, June 2011.
[RFC6275] Perkins, C., Johnson, D., and J. Arkko, "Mobility Support
in IPv6", RFC 6275, July 2011.
Templin Expires August 14, 2015 [Page 64]
Internet-Draft AERO February 2015
[RFC6355] Narten, T. and J. Johnson, "Definition of the UUID-Based
DHCPv6 Unique Identifier (DUID-UUID)", RFC 6355, August
2011.
[RFC6422] Lemon, T. and Q. Wu, "Relay-Supplied DHCP Options", RFC
6422, December 2011.
[RFC6438] Carpenter, B. and S. Amante, "Using the IPv6 Flow Label
for Equal Cost Multipath Routing and Link Aggregation in
Tunnels", RFC 6438, November 2011.
[RFC6691] Borman, D., "TCP Options and Maximum Segment Size (MSS)",
RFC 6691, July 2012.
[RFC6706] Templin, F., "Asymmetric Extended Route Optimization
(AERO)", RFC 6706, August 2012.
[RFC6864] Touch, J., "Updated Specification of the IPv4 ID Field",
RFC 6864, February 2013.
[RFC6935] Eubanks, M., Chimento, P., and M. Westerlund, "IPv6 and
UDP Checksums for Tunneled Packets", RFC 6935, April 2013.
[RFC6936] Fairhurst, G. and M. Westerlund, "Applicability Statement
for the Use of IPv6 UDP Datagrams with Zero Checksums",
RFC 6936, April 2013.
[RFC6939] Halwasia, G., Bhandari, S., and W. Dec, "Client Link-Layer
Address Option in DHCPv6", RFC 6939, May 2013.
[RFC6980] Gont, F., "Security Implications of IPv6 Fragmentation
with IPv6 Neighbor Discovery", RFC 6980, August 2013.
[RFC7078] Matsumoto, A., Fujisaki, T., and T. Chown, "Distributing
Address Selection Policy Using DHCPv6", RFC 7078, January
2014.
[TUNTAP] Wikipedia, W., "http://en.wikipedia.org/wiki/TUN/TAP",
October 2014.
Author's Address
Templin Expires August 14, 2015 [Page 65]
Internet-Draft AERO February 2015
Fred L. Templin (editor)
Boeing Research & Technology
P.O. Box 3707
Seattle, WA 98124
USA
Email: fltemplin@acm.org
Templin Expires August 14, 2015 [Page 66]