IPPM T. Zhou, Ed.
Internet-Draft Huawei
Intended status: Standards Track J. Guichard
Expires: July 5, 2020 Futurewei
F. Brockners
S. Raghavan
Cisco Systems
January 2, 2020
A YANG Data Model for In-Situ OAM
draft-zhou-ippm-ioam-yang-05
Abstract
In-situ Operations, Administration, and Maintenance (IOAM) records
operational and telemetry information in user packets while the
packets traverse a path between two points in the network. This
document defines a YANG module for the IOAM function.
Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on July 5, 2020.
Copyright Notice
Copyright (c) 2020 IETF Trust and the persons identified as the
document authors. All rights reserved.
Zhou, Ed., et al. Expires July 5, 2020 [Page 1]
Internet-Draft YANG Model for IOAM January 2020
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(https://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
1.1. Tree Diagrams . . . . . . . . . . . . . . . . . . . . . . 3
2. Design of the IOAM YANG Data Model . . . . . . . . . . . . . 3
2.1. Profiles . . . . . . . . . . . . . . . . . . . . . . . . 3
2.2. Preallocated Tracing Profile . . . . . . . . . . . . . . 4
2.3. Incremental Tracing Profile . . . . . . . . . . . . . . . 5
2.4. Proof of Transit Profile . . . . . . . . . . . . . . . . 5
2.5. Edge to Edge Profile . . . . . . . . . . . . . . . . . . 6
3. IOAM YANG Module . . . . . . . . . . . . . . . . . . . . . . 6
4. Security Considerations . . . . . . . . . . . . . . . . . . . 18
5. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 19
6. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 20
7. References . . . . . . . . . . . . . . . . . . . . . . . . . 20
7.1. Normative References . . . . . . . . . . . . . . . . . . 20
7.2. Informative References . . . . . . . . . . . . . . . . . 21
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 21
1. Introduction
In-situ Operations, Administration, and Maintenance (IOAM)
[I-D.ietf-ippm-ioam-data] records OAM information within user packets
while the packets traverse a network. The data types and data
formats for IOAM data records have been defined in
[I-D.ietf-ippm-ioam-data]. The IOAM data can be embedded in many
protocol encapsulations such as Network Services Header, Segment
Routing, and IPv6 [I-D.brockners-inband-oam-transport].
This document defines a data model for IOAM capabilities using the
YANG data modeling language [RFC7950]. This YANG model supports all
the three categories of IOAM data, which are Tracing Option, Proof of
Transit Option, and Edge-to-Edge Option.
Zhou, Ed., et al. Expires July 5, 2020 [Page 2]
Internet-Draft YANG Model for IOAM January 2020
1.1. Tree Diagrams
The meaning of the symbols in these diagrams is as follows:
o Brackets "[" and "]" enclose list keys.
o Curly braces "{" and "}" contain names of optional features that
make the corresponding node conditional.
o Abbreviations before data node names: "rw" means configuration
(read-write), "ro" state data (read-only).
o Symbols after data node names: "?" means an optional node, "!" a
container with presence, and "*" denotes a "list" or "leaf-list".
o Parentheses enclose choice and case nodes, and case nodes are also
marked with a colon (":").
o Ellipsis ("...") stands for contents of subtrees that are not
shown.
2. Design of the IOAM YANG Data Model
2.1. Profiles
The IOAM model is organized as list of profiles as shown in the
following figure. Each profile associates with one flow and the
corresponding IOAM information.
module: ietf-ioam
+--rw ioam
+--rw ioam-profiles
+--rw admin-config
| +--rw enabled? boolean
+--rw ioam-profile* [profile-name]
+--rw profile-name string
+--rw filter
| +--rw filter-type? ioam-filter-type
| +--rw acl-name? -> /acl:acls/acl/name
+--rw protocol-type? ioam-protocol-type
+--rw incremental-tracing-profile {incremental-trace}?
| ...
+--rw preallocated-tracing-profile {preallocated-trace}?
| ...
+--rw pot-profile {proof-of-transit}?
| ...
+--rw e2e-profile {edge-to-edge}?
...
Zhou, Ed., et al. Expires July 5, 2020 [Page 3]
Internet-Draft YANG Model for IOAM January 2020
The "enabled" is an administrative configuration. When it is set to
true, IOAM configuration is enabled for the system. Meanwhile, the
IOAM data-plane functionality is enabled.
The "filter" is used to identify a flow, where the IOAM profile can
apply. There may be multiple filter types. ACL is the default one.
The IOAM data can be encapsulated into multiple protocols, e.g., IPv6
[RFC8200], Geneve [I-D.ietf-nvo3-geneve],VxLAN-GPE
[I-D.ietf-nvo3-vxlan-gpe]. The "protocol-type" is used to indicate
where the IOAM is applied. For example, if the "protocol-type" is
IPv6, the IOAM ingress node will encapsulate the associated flow with
the IPv6-IOAM [I-D.brockners-inband-oam-transport] format.
IOAM data includes three usage options with four encapsulation types,
i.e., incremental tracing data, preallocated tracing data, prove of
transit data and end to end data. In practice, multiple IOAM data
types can be encapsulated into the same IOAM header. The "ioam-
profile" contains a set of sub-profiles, each of which relates to one
encapsulation type. The configured object may not support all the
sub-profiles. The supported sub-profiles are indicated by 4 defined
features, i.e., "incremental-trace", "preallocated-trace", "proof-of-
transit", "edge-to-edge".
2.2. Preallocated Tracing Profile
The IOAM tracing data is expected to be collected at every node that
a packet traverses to ensure visibility into the entire path a packet
takes within an IOAM domain. The preallocated tracing option will
create pre-allocated space for each node to populate its information
. The "preallocated-tracing-profile" contains the detailed
information for the preallocated tracing data. The information
includes:
o enabled: indicates whether the preallocated tracing profile is
enabled.
o node-action: indicates the operation (e.g., encapsulate IOAM
header, transit the IOAM data, or decapsulate IOAM header) applied
to the dedicated flow.
o use-namespace: indicate the namespace used for the trace types.
o trace-type: indicates the per-hop data to be captured by the IOAM
enabled nodes and included in the node data list.
o Loopback mode is used to send a copy of a packet back towards the
source.
Zhou, Ed., et al. Expires July 5, 2020 [Page 4]
Internet-Draft YANG Model for IOAM January 2020
+--rw preallocated-tracing-profile {preallocated-trace}?
+--rw enabled? boolean
+--rw node-action? ioam-node-action
+--rw trace-types
| +--rw use-namespace? ioam-namespace
| +--rw trace-type* ioam-trace-type
+--rw enable-loopback-mode? boolean
2.3. Incremental Tracing Profile
The incremental tracing option contains a variable node data fields
where each node allocates and pushes its node data immediately
following the option header. The "incremental-tracing-profile"
contains the detailed information for the incremental tracing data.
The detailed information is the same as the Preallocated Tracing
Profile, but with one more variable, "max-length", which restricts
the length of the IOAM header.
+--rw incremental-tracing-profile {incremental-trace}?
+--rw enabled? boolean
+--rw node-action? ioam-node-action
+--rw trace-types
| +--rw use-namespace? ioam-namespace
| +--rw trace-type* ioam-trace-type
+--rw enable-loopback-mode? boolean
+--rw max-length? uint32
2.4. Proof of Transit Profile
The IOAM Proof of Transit data is to support the path or service
function chain verification use cases. The "pot-profile" contains
the detailed information for the prove of transit data. The detailed
information are described in [I-D.brockners-proof-of-transit].
+--rw pot-profile {proof-of-transit}?
+--rw enabled? boolean
+--rw active-profile-index? pot:profile-index-range
+--rw pot-profile-list* [pot-profile-index]
+--rw pot-profile-index profile-index-range
+--rw prime-number uint64
+--rw secret-share uint64
+--rw public-polynomial uint64
+--rw lpc uint64
+--rw validator? boolean
+--rw validator-key? uint64
+--rw bitmask? uint64
Zhou, Ed., et al. Expires July 5, 2020 [Page 5]
Internet-Draft YANG Model for IOAM January 2020
2.5. Edge to Edge Profile
The IOAM edge to edge option is to carry data that is added by the
IOAM encapsulating node and interpreted by IOAM decapsulating node.
The "e2e-profile" contains the detailed information for the edge to
edge data. The detailed information includes:
o enabled: indicates whether the edge to edge profile is enabled.
o node-action is the same semantic as in Section 2.2.
o use-namespace: indicate the namespace used for the edge to edge
types.
o e2e-type indicates data to be carried from the ingress IOAM node
to the egress IOAM node.
+--rw e2e-profile {edge-to-edge}?
+--rw enabled? boolean
+--rw node-action? ioam-node-action
+--rw e2e-types
+--rw use-namespace? ioam-namespace
+--rw e2e-type* ioam-e2e-type
3. IOAM YANG Module
<CODE BEGINS> file "ietf-ioam@2018-06-27.yang"
module ietf-ioam {
yang-version 1.1;
namespace "urn:ietf:params:xml:ns:yang:ietf-ioam";
prefix "ioam";
import ietf-pot-profile {
prefix "pot";
}
import ietf-access-control-list {
prefix "acl";
}
organization
"IETF IPPM (IP Performance Metrics) Working Group";
contact
"WG Web: <http://tools.ietf.org/wg/ippm>
WG List: <ippm@ietf.org>
Editor: zhoutianran@huawei.com";
description
Zhou, Ed., et al. Expires July 5, 2020 [Page 6]
Internet-Draft YANG Model for IOAM January 2020
"This YANG module specifies a vendor-independent data
model for the in Situ OAM (iOAM).";
revision 2019-06-26 {
description "Initial revision.";
reference "draft-zhou-ippm-ioam-yang";
}
/*
* FEATURES
*/
feature incremental-trace
{
description
"This feature indicated that the incremental tracing mode is
supported";
}
feature preallocated-trace
{
description
"This feature indicated that the preallocated tracing mode is
supported";
}
feature proof-of-transit
{
description
"This feature indicated that the proof of transit mode is
supported";
}
feature edge-to-edge
{
description
"This feature indicated that the edge to edge mode is
supported";
}
/*
* IDENTITIES
*/
identity base-filter {
description
"Base identity to represent a filter. A filter is used to
specify the flow to apply the iOAM profile. ";
}
Zhou, Ed., et al. Expires July 5, 2020 [Page 7]
Internet-Draft YANG Model for IOAM January 2020
identity acl-filter {
base base-filter;
description
"Apply ACL rule to specify the flow.";
}
identity base-protocol {
description
"Base identity to represent the carrier protocol. It's used to
indicate what layer and protocol the iOAM data is embedded.";
}
identity ipv6-protocol {
base base-protocol;
description
"The described iOAM data is embedded in ipv6 protocol.";
}
identity base-node-action {
description
"Base identity to represent the node actions. It's used to
indicate what action the node will take.";
}
identity encapsulate {
base base-node-action;
description
"indicate the node is to encapsulate the iOAM packet";
}
identity transit {
base base-node-action;
description
"indicate the node is to transit the iOAM packet";
}
identity decapsulate {
base base-node-action;
description
"indicate the node is to decapsulate the iOAM packet";
}
identity base-trace-type {
description
"Base identity to represent trace types";
}
identity trace-hop-lim-node-id {
Zhou, Ed., et al. Expires July 5, 2020 [Page 8]
Internet-Draft YANG Model for IOAM January 2020
base base-trace-type;
description
"indicates presence of Hop_Lim and node_id in the
node data.";
}
identity trace-if-id {
base base-trace-type;
description
"indicates presence of ingress_if_id and egress_if_id in the
node data.";
}
identity trace-timestamp-seconds {
base base-trace-type;
description
"indicates presence of time stamp seconds in the node data.";
}
identity trace-timestamp-nanoseconds {
base base-trace-type;
description
"indicates presence of time stamp nanoseconds in the node data.";
}
identity trace-transit-delay {
base base-trace-type;
description
"indicates presence of transit delay in the node data.";
}
identity trace-namespace-data {
base base-trace-type;
description
"indicates presence of namespace specific data (short format)
in the node data.";
}
identity trace-queue-depth {
base base-trace-type;
description
"indicates presence of queue depth in the node data.";
}
identity trace-opaque-state-snapshot {
base base-trace-type;
description
"indicates presence of variable length Opaque State Snapshot
Zhou, Ed., et al. Expires July 5, 2020 [Page 9]
Internet-Draft YANG Model for IOAM January 2020
field.";
}
identity trace-hop-lim-node-id-wide {
base base-trace-type;
description
"indicates presence of Hop_Lim and node_id wide in the
node data.";
}
identity trace-if-id-wide {
base base-trace-type;
description
"indicates presence of ingress_if_id and egress_if_id wide in
the node data.";
}
identity trace-namespace-data-wide {
base base-trace-type;
description
"indicates presence of namespace specific data in wide format
in the node data.";
}
identity trace-buffer-occupancy {
base base-trace-type;
description
"indicates presence of buffer occupancy in the node data.";
}
identity trace-checksum-complement {
base base-trace-type;
description
"indicates presence of the Checksum Complement node data.";
}
identity base-pot-type {
description
"Base identity to represent pot types";
}
identity pot-bytes-16 {
base base-pot-type;
description
"POT data is a 16 Octet field.";
}
identity base-e2e-type {
Zhou, Ed., et al. Expires July 5, 2020 [Page 10]
Internet-Draft YANG Model for IOAM January 2020
description
"Base identity to represent e2e types";
}
identity e2e-seq-num-64 {
base base-e2e-type;
description
"indicates presence of a 64-bit sequence number";
}
identity e2e-seq-num-32 {
base base-e2e-type;
description
"indicates presence of a 32-bit sequence number";
}
identity e2e-timestamp-seconds {
base base-e2e-type;
description
"indicates presence of timestamp seconds for the
transmission of the frame";
}
identity e2e-timestamp-subseconds {
base base-e2e-type;
description
"indicates presence of timestamp subseconds for the
transmission of the frame";
}
identity base-namespace {
description
"Base identity to represent the namespace";
}
identity namespace-ietf {
base base-namespace;
description
"namespace that specified in IETF.";
}
/*
* TYPE DEFINITIONS
*/
typedef ioam-filter-type {
type identityref {
base base-filter;
Zhou, Ed., et al. Expires July 5, 2020 [Page 11]
Internet-Draft YANG Model for IOAM January 2020
}
description
"Specifies a known type of filter.";
}
typedef ioam-protocol-type {
type identityref {
base base-protocol;
}
description
"Specifies a known type of carrier protocol for the iOAM data.";
}
typedef ioam-node-action {
type identityref {
base base-node-action;
}
description
"Specifies a known type of node action.";
}
typedef ioam-trace-type {
type identityref {
base base-trace-type;
}
description
"Specifies a known trace type.";
}
typedef ioam-pot-type {
type identityref {
base base-pot-type;
}
description
"Specifies a known pot type.";
}
typedef ioam-e2e-type {
type identityref {
base base-e2e-type;
}
description
"Specifies a known e2e type.";
}
typedef ioam-namespace {
type identityref {
base base-namespace;
Zhou, Ed., et al. Expires July 5, 2020 [Page 12]
Internet-Draft YANG Model for IOAM January 2020
}
description
"Specifies the supported namespace.";
}
/*
* GROUP DEFINITIONS
*/
grouping ioam-filter {
description "A grouping for iOAM filter definition";
leaf filter-type {
type ioam-filter-type;
description "filter type";
}
leaf acl-name {
when "../filter-type = 'acl-filter'";
type leafref {
path "/acl:acls/acl:acl/acl:name";
}
description "Access Control List name.";
}
}
grouping ioam-incremental-tracing-profile {
description
"A grouping for incremental tracing profile.";
leaf node-action {
type ioam-node-action;
description "node action";
}
container trace-types {
when "../node-action = 'encapsulate'";
description
"the list of trace types for encapsulate";
leaf use-namespace {
type ioam-namespace;
description
"the namespace used for the encapsulation";
}
leaf-list trace-type {
type ioam-trace-type;
Zhou, Ed., et al. Expires July 5, 2020 [Page 13]
Internet-Draft YANG Model for IOAM January 2020
description
"The trace type is only defined at the encapsulation node.";
}
}
leaf enable-loopback-mode {
when "../node-action = 'encapsulate'";
type boolean;
default false;
description
"Loopback mode is used to send a copy of a packet back towards
the source. The loopback mode is only defined at the
encapsulation node.";
}
leaf max-length {
when "../node-action = 'encapsulate'";
type uint32;
description
"This field specifies the maximum length of the node data list
in octets. The max-length is only defined at the
encapsulation node. And it's only used for the incremental
tracing mode.";
}
}
grouping ioam-preallocated-tracing-profile {
description
"A grouping for incremental tracing profile.";
leaf node-action {
type ioam-node-action;
description "node action";
}
container trace-types {
when "../node-action = 'encapsulate'";
description
"the list of trace types for encapsulate";
leaf use-namespace {
type ioam-namespace;
description
"the namespace used for the encapsulation";
}
leaf-list trace-type {
type ioam-trace-type;
Zhou, Ed., et al. Expires July 5, 2020 [Page 14]
Internet-Draft YANG Model for IOAM January 2020
description
"The trace type is only defined at the encapsulation node.";
}
}
leaf enable-loopback-mode {
when "../node-action = 'encapsulate'";
type boolean;
default false;
description
"Loopback mode is used to send a copy of a packet back towards
the source. The loopback mode is only defined at the
encapsulation node.";
}
}
grouping ioam-e2e-profile {
description
"A grouping for tracing profile.";
leaf node-action {
type ioam-node-action;
description
"indicate how the node act for this profile";
}
container e2e-types {
when "../node-action = 'encapsulate'";
description
"the list of e2e types for encapsulate";
leaf use-namespace {
type ioam-namespace;
description
"the namespace used for the encapsulation";
}
leaf-list e2e-type {
type ioam-e2e-type;
description
"The e2e type is only defined at the encapsulation node.";
}
}
}
grouping ioam-admin-config {
description
"IOAM top-level administrative configuration.";
Zhou, Ed., et al. Expires July 5, 2020 [Page 15]
Internet-Draft YANG Model for IOAM January 2020
leaf enabled {
type boolean;
default false;
description
"When true, IOAM configuration is enabled for the system.
Meanwhile, the IOAM data-plane functionality is enabled.";
}
}
/*
* DATA NODES
*/
container ioam {
description "iOAM top level container";
container ioam-profiles {
description
"Contains a list of iOAM profiles.";
container admin-config {
description
"Contains all the administrative configurations related to
the IOAM functionalities and all the IOAM profiles.";
uses ioam-admin-config;
}
list ioam-profile {
key "profile-name";
ordered-by user;
description
"A list of iOAM profiles that configured on the node.";
leaf profile-name {
type string;
mandatory true;
description
"Unique identifier for each iOAM profile";
}
container filter {
uses ioam-filter;
description
"The filter which is used to indicate the flow to apply
iOAM.";
}
Zhou, Ed., et al. Expires July 5, 2020 [Page 16]
Internet-Draft YANG Model for IOAM January 2020
leaf protocol-type {
type ioam-protocol-type;
description
"This item is used to indicate the carrier protocol where
the iOAM is applied.";
}
container incremental-tracing-profile {
if-feature incremental-trace;
description
"describe the profile for incremental tracing option";
leaf enabled {
type boolean;
default false;
description
"When true, apply incremental tracing option to the
specified flow identified by the filter.";
}
uses ioam-incremental-tracing-profile;
}
container preallocated-tracing-profile {
if-feature preallocated-trace;
description
"describe the profile for preallocated tracing option";
leaf enabled {
type boolean;
default false;
description
"When true, apply preallocated tracing option to the
specified flow identified by the following filter.";
}
uses ioam-preallocated-tracing-profile;
}
container pot-profile {
if-feature proof-of-transit;
description
"describe the profile for pot option";
leaf enabled {
type boolean;
default false;
description
Zhou, Ed., et al. Expires July 5, 2020 [Page 17]
Internet-Draft YANG Model for IOAM January 2020
"When true, apply Proof of Transit option to the
specified flow identified by the following filter.";
}
leaf active-profile-index {
type pot:profile-index-range;
description
"Proof of transit profile index that is currently
active. Will be set in the first hop of the path
or chain. Other nodes will not use this field.";
}
uses pot:pot-profile;
}
container e2e-profile {
if-feature edge-to-edge;
description
"describe the profile for e2e option";
leaf enabled {
type boolean;
default false;
description
"When true, apply End to end option to the
specified flow identified by the following filter.";
}
uses ioam-e2e-profile;
}
}
}
}
}
<CODE ENDS>
4. Security Considerations
The YANG module specified in this document defines a schema for data
that is designed to be accessed via network management protocols such
as NETCONF [RFC6241] or RESTCONF [RFC8040]. The lowest NETCONF layer
is the secure transport layer, and the mandatory-to-implement secure
transport is Secure Shell (SSH) [RFC6242]. The lowest RESTCONF layer
is HTTPS, and the mandatory-to-implement secure transport is TLS
[RFC5246].
The NETCONF access control model [RFC6536] provides the means to
restrict access for particular NETCONF or RESTCONF users to a
Zhou, Ed., et al. Expires July 5, 2020 [Page 18]
Internet-Draft YANG Model for IOAM January 2020
preconfigured subset of all available NETCONF or RESTCONF protocol
operations and content.
There are a number of data nodes defined in this YANG module that are
writable/creatable/deletable (i.e., config true, which is the
default). These data nodes may be considered sensitive or vulnerable
in some network environments. Write operations (e.g., edit-config)
to these data nodes without proper protection can have a negative
effect on network operations. These are the subtrees and data nodes
and their sensitivity/vulnerability:
o /ioam/ioam-profiles/admin-config
The items in the container above include the top level administrative
configurations related to the IOAM functionalities and all the IOAM
profiles. Unexpected changes to these items could lead to the IOAM
function disruption and/ or misbehavior of all the IOAM profiles.
o /ioam/ioam-profiles/ioam-profile
The entries in the list above include the whole IOAM profile
configurations which indirectly create or modify the device
configurations. Unexpected changes to these entries could lead to
the mistake of the IOAM behavior for the corresponding flows.
5. IANA Considerations
RFC Ed.: In this section, replace all occurrences of 'XXXX' with the
actual RFC number (and remove this note).
IANA is requested to assign a new URI from the IETF XML Registry
[RFC3688]. The following URI is suggested:
URI: urn:ietf:params:xml:ns:yang:ietf-ioam
Registrant Contact: The IESG.
XML: N/A; the requested URI is an XML namespace.
This document also requests a new YANG module name in the YANG Module
Names registry [RFC7950] with the following suggestion:
name: ietf-ioam
namespace: urn:ietf:params:xml:ns:yang:ietf-ioam
prefix: ioam
reference: RFC XXXX
Zhou, Ed., et al. Expires July 5, 2020 [Page 19]
Internet-Draft YANG Model for IOAM January 2020
6. Acknowledgements
For their valuable comments, discussions, and feedback, we wish to
acknowledge Greg Mirsky and Reshad Rahman.
7. References
7.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/info/rfc2119>.
[RFC3688] Mealling, M., "The IETF XML Registry", BCP 81, RFC 3688,
DOI 10.17487/RFC3688, January 2004,
<https://www.rfc-editor.org/info/rfc3688>.
[RFC5246] Dierks, T. and E. Rescorla, "The Transport Layer Security
(TLS) Protocol Version 1.2", RFC 5246,
DOI 10.17487/RFC5246, August 2008,
<https://www.rfc-editor.org/info/rfc5246>.
[RFC6241] Enns, R., Ed., Bjorklund, M., Ed., Schoenwaelder, J., Ed.,
and A. Bierman, Ed., "Network Configuration Protocol
(NETCONF)", RFC 6241, DOI 10.17487/RFC6241, June 2011,
<https://www.rfc-editor.org/info/rfc6241>.
[RFC6242] Wasserman, M., "Using the NETCONF Protocol over Secure
Shell (SSH)", RFC 6242, DOI 10.17487/RFC6242, June 2011,
<https://www.rfc-editor.org/info/rfc6242>.
[RFC6536] Bierman, A. and M. Bjorklund, "Network Configuration
Protocol (NETCONF) Access Control Model", RFC 6536,
DOI 10.17487/RFC6536, March 2012,
<https://www.rfc-editor.org/info/rfc6536>.
[RFC7950] Bjorklund, M., Ed., "The YANG 1.1 Data Modeling Language",
RFC 7950, DOI 10.17487/RFC7950, August 2016,
<https://www.rfc-editor.org/info/rfc7950>.
[RFC8040] Bierman, A., Bjorklund, M., and K. Watsen, "RESTCONF
Protocol", RFC 8040, DOI 10.17487/RFC8040, January 2017,
<https://www.rfc-editor.org/info/rfc8040>.
Zhou, Ed., et al. Expires July 5, 2020 [Page 20]
Internet-Draft YANG Model for IOAM January 2020
[RFC8200] Deering, S. and R. Hinden, "Internet Protocol, Version 6
(IPv6) Specification", STD 86, RFC 8200,
DOI 10.17487/RFC8200, July 2017,
<https://www.rfc-editor.org/info/rfc8200>.
7.2. Informative References
[I-D.brockners-inband-oam-transport]
Brockners, F., Bhandari, S., Govindan, V., Pignataro, C.,
Gredler, H., Leddy, J., Youell, S., Mizrahi, T., Mozes,
D., Lapukhov, P., and R. Chang, "Encapsulations for In-
situ OAM Data", draft-brockners-inband-oam-transport-05
(work in progress), July 2017.
[I-D.brockners-proof-of-transit]
Brockners, F., Bhandari, S., Dara, S., Pignataro, C.,
Leddy, J., Youell, S., Mozes, D., and T. Mizrahi, "Proof
of Transit", draft-brockners-proof-of-transit-05 (work in
progress), May 2018.
[I-D.ietf-ippm-ioam-data]
Brockners, F., Bhandari, S., Pignataro, C., Gredler, H.,
Leddy, J., Youell, S., Mizrahi, T., Mozes, D., Lapukhov,
P., remy@barefootnetworks.com, r., daniel.bernier@bell.ca,
d., and J. Lemon, "Data Fields for In-situ OAM", draft-
ietf-ippm-ioam-data-08 (work in progress), October 2019.
[I-D.ietf-nvo3-geneve]
Gross, J., Ganga, I., and T. Sridhar, "Geneve: Generic
Network Virtualization Encapsulation", draft-ietf-
nvo3-geneve-14 (work in progress), September 2019.
[I-D.ietf-nvo3-vxlan-gpe]
Maino, F., Kreeger, L., and U. Elzur, "Generic Protocol
Extension for VXLAN", draft-ietf-nvo3-vxlan-gpe-09 (work
in progress), December 2019.
Authors' Addresses
Tianran Zhou
Huawei
156 Beiqing Rd.
Beijing 100095
China
Email: zhoutianran@huawei.com
Zhou, Ed., et al. Expires July 5, 2020 [Page 21]
Internet-Draft YANG Model for IOAM January 2020
Jim Guichard
Futurewei
United States of America
Email: james.n.guichard@futurewei.com
Frank Brockners
Cisco Systems
Hansaallee 249, 3rd Floor
Duesseldorf, Nordrhein-Westfalen 40549
Germany
Email: fbrockne@cisco.com
Srihari Raghavan
Cisco Systems
Tril Infopark Sez, Ramanujan IT City
Neville Block, 2nd floor, Old Mahabalipuram Road
Chennai, Tamil Nadu 600113
India
Email: srihari@cisco.com
Zhou, Ed., et al. Expires July 5, 2020 [Page 22]