Network Working Group                                   Fatai Zhang, Ed.
Internet Draft                                                    Huawei
Category: Standards Track                                  Guoying Zhang
                                                                    CATR
                                                          Sergio Belotti
                                                          Alcatel-Lucent
                                                           D. Ceccarelli
                                                                Ericsson
                                                        Khuzema Pithewan
                                                                Infinera
Expires: September 9, 2012                                 March 9, 2012


      Generalized Multi-Protocol Label Switching (GMPLS) Signaling
  Extensions for the evolving G.709 Optical Transport Networks Control


              draft-ietf-ccamp-gmpls-signaling-g709v3-02.txt


Status of this Memo

   This Internet-Draft is submitted to IETF in full conformance with
   the provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF), its areas, and its working groups.  Note that
   other groups may also distribute working documents as Internet-
   Drafts.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   The list of current Internet-Drafts can be accessed at
   http://www.ietf.org/ietf/1id-abstracts.txt.

   The list of Internet-Draft Shadow Directories can be accessed at
   http://www.ietf.org/shadow.html.

   This Internet-Draft will expire on September 9, 2012.



Abstract

   Recent progress in ITU-T Recommendation G.709 standardization has
   introduced new ODU containers (ODU0, ODU4, ODU2e and ODUflex) and



Zhang                  Expires September 2012                 [Page 1]


draft-ietf-ccamp-gmpls-signaling-g709v3-02.txt              March 2012


   enhanced Optical Transport Networking (OTN) flexibility. Several
   recent documents have proposed ways to modify GMPLS signaling
   protocols to support these new OTN features.

   It is important that a single solution is developed for use in GMPLS
   signaling and routing protocols. This solution must support ODUk
   multiplexing capabilities, address all of the new features, be
   acceptable to all equipment vendors, and be extensible considering
   continued OTN evolution.

   This document describes the extensions to the Generalized Multi-
   Protocol Label Switching (GMPLS) signaling to control the evolving
   Optical Transport Networks (OTN) addressing ODUk multiplexing and new
   features including ODU0, ODU4, ODU2e and ODUflex.



Conventions used in this document

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in [RFC2119].



Table of Contents

   1. Introduction .................................................. 3
   2. Terminology ................................................... 4
   3. GMPLS Extensions for the Evolving G.709 - Overview ............ 4
   4. Generalized Label Request ..................................... 5
   5. Extensions for Traffic Parameters for the Evolving G.709 ...... 5
      5.1. Usage of ODUflex(CBR) Traffic Parameters ................. 7
      5.2. Usage of ODUflex(GFP) Traffic Parameters ................. 9
   6. Generalized Label ............................................. 9
      6.1. New definition of ODU Generalized Label ................. 10
      6.2. Examples ................................................ 12
      6.3. Label Distribution Procedure ............................ 14
         6.3.1. Notification on Label Error ........................ 15
      6.4. Supporting Virtual Concatenation and Multiplication ..... 15
   7. Supporting Multiplexing Hierarchy ............................ 16
      7.1. ADAPTATION Object ....................................... 17
      7.2. ODU FA-LSP Creation ..................................... 19
   8. Supporting Hitless Adjustment of ODUflex (GFP) ............... 20
   9. Control Plane Backward Compatibility Considerations........... 21
   10. Security Considerations ..................................... 22
   11. IANA Considerations.......................................... 22


Zhang                  Expires September 2012                 [Page 2]


draft-ietf-ccamp-gmpls-signaling-g709v3-02.txt              March 2012


   12. References .................................................. 23
      12.1. Normative References ................................... 23
      12.2. Informative References ................................. 24
   13. Contributors ................................................ 25
   14. Authors' Addresses .......................................... 25
   15. Acknowledgment .............................................. 28

1. Introduction

   Generalized Multi-Protocol Label Switching (GMPLS) [RFC3945] extends
   MPLS to include Layer-2 Switching (L2SC), Time-Division Multiplex
   (e.g., SONET/SDH, PDH, and ODU), Wavelength (OCh, Lambdas) Switching,
   and Spatial Switching (e.g., incoming port or fiber to outgoing port
   or fiber). [RFC3471] presents a functional description of the
   extensions to Multi-Protocol Label Switching (MPLS) signaling
   required to support Generalized MPLS.  RSVP-TE-specific formats and
   mechanisms and technology specific details are defined in [RFC3473].

   With the evolution and deployment of G.709 technology, it is
   necessary that appropriate enhanced control technology support be
   provided for G.709. [RFC4328] describes the control technology
   details that are specific to foundation G.709 Optical Transport
   Networks (OTN), as specified in the ITU-T Recommendation G.709 [G709-
   V1], for ODUk deployments without multiplexing.

   In addition to increasing need to support ODUk multiplexing, the
   evolution of OTN has introduced additional containers and new
   flexibility. For example, ODU0, ODU2e, ODU4 containers and ODUflex
   are developed in [G709-V3].

   In addition, the following issues require consideration:

      -  Support for Hitless Adjustment of ODUflex (GFP) (HAO), which is
         defined in [G.7044].

      -  Support for Tributary Port Number. The Tributary Port Number
         has to be negotiated on each link for flexible assignment of
         tributary ports to tributary slots in case of LO-ODU over HO-
         ODU (e.g., ODU2 into ODU3).

   Therefore, it is clear that [RFC4328] has to be updated or superceded
   in order to support ODUk multiplexing, as well as other ODU
   enhancements introduced by evolution of OTN standards.

   This document updates [RFC4328] extending the G.709 ODUk traffic
   parameters and also presents a new OTN label format which is very
   flexible and scalable.


Zhang                  Expires September 2012                 [Page 3]


draft-ietf-ccamp-gmpls-signaling-g709v3-02.txt              March 2012


2. Terminology

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in [RFC2119].

3. GMPLS Extensions for the Evolving G.709 - Overview

   New features for the evolving OTN, for example, new ODU0, ODU2e, ODU4
   and ODUflex containers are specified in [G709-V3]. The corresponding
   new signal types are summarized below:

      - Optical Channel Transport Unit (OTUk):
         . OTU4

      - Optical Channel Data Unit (ODUk):
         . ODU0
         . ODU2e
         . ODU4
         . ODUflex

   A new Tributary Slot (TS) granularity (i.e., 1.25 Gbps) is also
   described in [G709-V3]. Thus, there are now two TS granularities for
   the foundation OTN ODU1, ODU2 and ODU3 containers. The TS granularity
   at 2.5 Gbps is used on legacy interfaces while the new 1.25 Gbps is
   used on the new interfaces.

   In addition to the support of ODUk mapping into OTUk (k = 1, 2, 3, 4),
   the evolving OTN [G.709-V3] encompasses the multiplexing of ODUj (j =
   0, 1, 2, 2e, 3, flex) into an ODUk (k > j), as described in Section
   3.1.2 of [OTN-FWK].

   Virtual Concatenation (VCAT) of OPUk (OPUk-Xv, k = 1/2/3, X = 1...256)
   is also supported by [OTN-V3]. Note that VCAT of OPU0 / OPU2e / OPU4
   / OPUflex is not supported per [OTN-V3].

   [RFC4328] describes GMPLS signaling extensions to support the control
   for G.709 Optical Transport Networks (OTN) [G709-V1]. However,
   [RFC4328] needs to be updated because it does not provide the means
   to signal all the new signal types and related mapping and
   multiplexing functionalities. Moreover, it supports only the
   deprecated auto-MSI mode which assumes that the Tributary Port Number
   is automatically assigned in the transmit direction and not checked
   in the receive direction.

   This document extends the G.709 traffic parameters described in
   [RFC4328] and presents a new flexible and scalable OTN label format.


Zhang                  Expires September 2012                 [Page 4]


draft-ietf-ccamp-gmpls-signaling-g709v3-02.txt              March 2012


   Additionally, procedures about Tributary Port Number assignment
   through control plane are also provided in this document.

4. Generalized Label Request

   The Generalized Label Request, as described in [RFC3471], carries the
   LSP Encoding Type, the Switching Type and the Generalized Protocol
   Identifier (G-PID).

   [RFC4328] extends the Generalized Label Request, introducing two new
   code-points for the LSP Encoding Type (i.e., G.709 ODUk (Digital Path)
   and G.709 Optical Channel) and adding a list of G-PID values in order
   to accommodate [G709-v1].

   This document follows these extensions and a new Switching Type is
   introduced to indicate the ODUk switching capability [G709-V3] in
   order to support backward compatibility with [RFC4328], as described
   in [OTN-FWK]. The new Switching Type (101, TBA by IANA) is defined in
   [OTN-OSPF].



5. Extensions for Traffic Parameters for the Evolving G.709

   The traffic parameters for G.709 are defined as follows:

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |  Signal Type  |   Reserved    |           NMC/ Tolerance      |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |              NVC              |        Multiplier (MT)        |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                            Bit_Rate                           |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   The Signal Type needs to be extended in order to cover the new Signal
   Type introduced by the evolving OTN. The new Signal Type values are
   extended as follows:

      Value    Type
      -----    ----
      0        Not significant
      1        ODU1 (i.e., 2.5 Gbps)
      2        ODU2 (i.e., 10 Gbps)
      3        ODU3 (i.e., 40 Gbps)


Zhang                  Expires September 2012                 [Page 5]


draft-ietf-ccamp-gmpls-signaling-g709v3-02.txt              March 2012


      4        ODU4 (i.e., 100 Gbps)
      5        Reserved (for future use)
      6        OCh at 2.5 Gbps
      7        OCh at 10 Gbps
      8        OCh at 40 Gbps
      9        OCh at 100 Gbps
      10       ODU0 (i.e., 1.25 Gbps)
      11       ODU2e (i.e., 10Gbps for FC1200 and GE LAN)
      12~19    Reserved (for future use)
      20       ODUflex(CBR) (i.e., 1.25*N Gbps)
      21       ODUflex(GFP-F), resizable (i.e., 1.25*N Gbps)
      22       ODUflex(GFP-F), non resizable (i.e., 1.25*N Gbps)
      23~255   Reserved (for future use)

   NMC/Tolerance:

   This field is redefined from the original definition in [RFC4328].
   NMC field defined in [RFC4328] cannot be fixed value for an end-to-
   end circuit involving dissimilar OTN link types. For example, ODU2e
   requires 9 TS on ODU3 and 8 TS on ODU4. Usage of NMC field is
   deprecated and should be used only with [RFC4328] generalized label
   format for backwards compatibility reasons. For the new generalized
   label format as defined in this document this field is interpreted as
   Tolerance.

   In case of ODUflex(CBR), the Bit_Rate and Tolerance fields MUST be
   used together to represent the actual bandwidth of ODUflex, where:

   -  The Bit_Rate field indicates the nominal bit rate of ODUflex(CBR)
      expressed in bytes per second, encoded as a 32-bit IEEE single-
      precision floating-point number (referring to [RFC4506] and
      [IEEE]). The value contained in the Bit Rate field has to keep
      into account both 239/238 factor and the Transcoding factor.

   -  The Tolerance field indicates the bit rate tolerance (part per
      million, ppm) of the ODUflex(CBR) encoded as an unsigned integer,
      which is bounded in 0~100ppm.

   For example, for an ODUflex(CBR) service with Bit_Rate = 2.5Gbps and
   Tolerance = 100ppm, the actual bandwidth of the ODUflex is:

                         2.5Gbps * (1 +/- 100ppm)

   In case of ODUflex(GFP), the Bit_Rate field is used to indicate the
   nominal bit rate of the ODUflex(GFP), which implies the number of


Zhang                  Expires September 2012                 [Page 6]


draft-ietf-ccamp-gmpls-signaling-g709v3-02.txt              March 2012


   tributary slots requested for the ODUflex(GFP). Since the tolerance
   of ODUflex(GFP) makes no sense on tributary slot resource reservation,
   the Tolerance field for ODUflex(GFP) is not necessary and MUST be
   filled with 0.

   In case of other ODUk signal types, the Bit_Rate and Tolerance fields
   are not necessary and MUST be set to 0.

   The usage of the NVC and Multiplier (MT) fields are the same as
   [RFC4328].

5.1. Usage of ODUflex(CBR) Traffic Parameters

   In case of ODUflex(CBR), the information of Bit_Rate and Tolerance in
   the ODUflex traffic parameters MUST be used to determine the total
   number of tributary slots N in the HO ODUk link to be reserved. Here:

         N = Ceiling of

   ODUflex(CBR) nominal bit rate * (1 + ODUflex(CBR) bit rate tolerance)
   ---------------------------------------------------------------------
       ODTUk.ts nominal bit rate * (1 - HO OPUk bit rate tolerance)

   In this formula, the ODUflex(CBR) nominal bit rate is the bit rate of
   the ODUflex(CBR) on the line side, i.e., the client signal bit rate
   after applying the 239/238 factor (according to clause 7.3 table 7.2
   of [G709-V3]) and the transcoding factor T (if needed) on the CBR
   client. According to clauses 17.7.3, 17.7.4 and 17.7.5 of [G709-V3]:

   ODUflex(CBR) nominal bit rate = CBR client bit rate * (239/238) / T

   The ODTUk.ts nominal bit rate is the nominal bit rate of the
   tributary slot of ODUk, as shown in Table 1 (referring to [G709-V3]).

              Table 1 - Actual TS bit rate of ODUk (in Gbps)

      ODUk.ts       Minimum          Nominal          Maximum
      ----------------------------------------------------------
      ODU2.ts    1.249 384 632    1.249 409 620    1.249 434 608
      ODU3.ts    1.254 678 635    1.254 703 729    1.254 728 823
      ODU4.ts    1.301 683 217    1.301 709 251    1.301 735 285

      Note that:

      Minimum bit rate of ODUTk.ts =
         ODTUk.ts nominal bit rate * (1 - HO OPUk bit rate tolerance)



Zhang                  Expires September 2012                 [Page 7]


draft-ietf-ccamp-gmpls-signaling-g709v3-02.txt              March 2012



      Maximum bit rate of ODTUk.ts =
         ODTUk.ts nominal bit rate * (1 + HO OPUk bit rate tolerance)

      Where: HO OPUk bit rate tolerance = 20ppm

   Therefore, a node receiving a PATH message containing ODUflex(CBR)
   nominal bit rate and tolerance can allocate precise number of
   tributary slots and set up the cross-connection for the ODUflex
   service.

   Note that for different ODUk, the bit rates of the tributary slots
   are different, and so the total number of tributary slots to be
   reserved for the ODUflex(CBR) may not be the same on different HO
   ODUk links.

   An example is given below to illustrate the usage of ODUflex(CBR)
   traffic parameters.

   As shown in Figure 1, assume there is an ODUflex(CBR) service
   requesting a bandwidth of (2.5Gbps, +/-100ppm) from node A to node C.
   In other words, the ODUflex traffic parameters indicate that Signal
   Type is 20 (ODUflex(CBR)), Bit_Rate is 2.5Gbps and Tolerance is
   100ppm.

     +-----+             +---------+             +-----+
     |     +-------------+ +-----+ +-------------+     |
     |     +=============+\| ODU |/+=============+     |
     |     +=============+/| flex+-+=============+     |
     |     +-------------+ |     |\+=============+     |
     |     +-------------+ +-----+ +-------------+     |
     |     |             |         |             |     |
     |     |   .......   |         |   .......   |     |
     |  A  +-------------+    B    +-------------+  C  |
     +-----+   HO ODU4   +---------+   HO ODU2   +-----+

       =========: TS occupied by ODUflex
       ---------: free TS

           Figure 1 - Example of ODUflex(CBR) Traffic Parameters



   -  On the HO ODU4 link between node A and B:

      The maximum bit rate of the ODUflex(CBR) equals 2.5Gbps * (1 +
      100ppm), and the minimum bit rate of the tributary slot of ODU4


Zhang                  Expires September 2012                 [Page 8]


draft-ietf-ccamp-gmpls-signaling-g709v3-02.txt              March 2012


      equals 1.301 683 217Gbps, so the total number of tributary slots
      N1 to be reserved on this link is:

      N1 = ceiling (2.5Gbps * (1 + 100ppm) / 1.301 683 217Gbps) = 2

   -  On the HO ODU2 link between node B and C:

      The maximum bit rate of the ODUflex equals 2.5Gbps * (1 + 100ppm),
      and the minimum bit rate of the tributary slot of ODU2 equals
      1.249 384 632Gbps, so the total number of tributary slots N2 to
      be reserved on this link is:

      N2 = ceiling (2.5Gbps * (1 + 100ppm) / 1.249 384 632Gbps) = 3



5.2. Usage of ODUflex(GFP) Traffic Parameters

   [G709-V3-A2] recommends that the ODUflex(GFP) will fill an integral
   number of tributary slots of the smallest HO ODUk path over which the
   ODUflex(GFP) may be carried, as shown in Table 2.

         Table 2 - Recommended ODUflex(GFP) bit rates and tolerance

              ODU type             | Nominal bit-rate | Tolerance
   --------------------------------+------------------+-----------
   ODUflex(GFP) of n TS, 1<=n<=8   |   n * ODU2.ts    | +/-100 ppm
   ODUflex(GFP) of n TS, 9<=n<=32  |   n * ODU3.ts    | +/-100 ppm
   ODUflex(GFP) of n TS, 33<=n<=80 |   n * ODU4.ts    | +/-100 ppm

   According to this table, the Bit_Rate field for ODUflex(GFP) MUST
   equal to one of the 80 values listed below:

       1 * ODU2.ts; 2 * ODU2.ts; ...; 8 * ODU2.ts;
       9 * ODU3.ts; 10 * ODU3.ts, ...; 32 * ODU3.ts;
       33 * ODU4.ts; 34 * ODU4.ts; ...; 80 * ODU4.ts.

   In this way, the number of required tributary slots for the
   ODUflex(GFP) (i.e., the value of "n" in Table 2) can be deduced from
   the Bit_Rate field.



6. Generalized Label

   [RFC3471] has defined the Generalized Label which extends the
   traditional label by allowing the representation of not only labels


Zhang                  Expires September 2012                 [Page 9]


draft-ietf-ccamp-gmpls-signaling-g709v3-02.txt              March 2012


   which are sent in-band with associated data packets, but also labels
   which identify time-slots, wavelengths, or space division multiplexed
   positions. The format of the corresponding RSVP-TE Generalized Label
   object is defined in the Section 2.3 of [RFC3473].

   However, for different technologies, we usually need use specific
   label rather than the Generalized Label. For example, the label
   format described in [RFC4606] could be used for SDH/SONET, the label
   format in [RFC4328] for G.709.



6.1. New definition of ODU Generalized Label

   In order to be compatible with new types of ODU signal and new types
   of tributary slot, the following new ODU label format MUST be used:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |         TPN           |   Reserved    |        Length         |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   ~             Bit Map         .........                         ~
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   The ODU Generalized Label is used to indicate how the LO ODUj signal
   is multiplexed into the HO ODUk link. Note that the LO OUDj signal
   type is indicated by traffic parameters, while the type of HO ODUk
   link can be figured out locally according to the identifier of the
   selected interface carried in the IF_ID RSVP_HOP Object.

   TPN (12 bits): indicates the Tributary Port Number (TPN) for the
   assigned Tributary Slot(s).

      -  In case of LO ODUj multiplexed into HO ODU1/ODU2/ODU3, only the
         lower 6 bits of TPN field are significant and the other bits of
         TPN MUST be set to 0.

      -  In case of LO ODUj multiplexed into HO ODU4, only the lower 7
         bits of TPN field are significant and the other bits of TPN
         MUST be set to 0.

      -  In case of ODUj mapped into OTUk (j=k), the TPN is not needed
         and this field MUST be set to 0.

   As per [G709-V3], The TPN is used to allow for correct demultiplexing
   in the data plane. When an LO ODUj is multiplexed into HO ODUk


Zhang                  Expires September 2012                [Page 10]


draft-ietf-ccamp-gmpls-signaling-g709v3-02.txt              March 2012


   occupying one or more TSs, a new TPN value is configured at the two
   ends of the HO ODUk link and is put into the related MSI byte(s) in
   the OPUk overhead at the (traffic) ingress end of the link, so that
   the other end of the link can learn which TS(s) is/are used by the LO
   ODUj in the data plane.

   According to [G709-V3], the TPN field MUST be set as according to the
   following tables:


          Table 3 - TPN Assignment Rules (2.5Gbps TS granularity)
   +-------+-------+----+----------------------------------------------+
   |HO ODUk|LO ODUj|TPN |          TPN Assignment Rules                |
   +-------+-------+----+----------------------------------------------+
   | ODU2  | ODU1  |1~4 |Fixed, = TS# occupied by ODU1                 |
   +-------+-------+----+----------------------------------------------+
   |       | ODU1  |1~16|Fixed, = TS# occupied by ODU1                 |
   | ODU3  +-------+----+----------------------------------------------+
   |       | ODU2  |1~4 |Flexible, != other existing LO ODU2s' TPNs    |
   +-------+-------+----+----------------------------------------------+



          Table 4 - TPN Assignment Rules (1.25Gbps TS granularity)
   +-------+-------+----+----------------------------------------------+
   |HO ODUk|LO ODUj|TPN |          TPN Assignment Rules                |
   +-------+-------+----+----------------------------------------------+
   | ODU1  | ODU0  |1~2 |Fixed, = TS# occupied by ODU0                 |
   +-------+-------+----+----------------------------------------------+
   |       | ODU1  |1~4 |Flexible, != other existing LO ODU1s' TPNs    |
   | ODU2  +-------+----+----------------------------------------------+
   |       |ODU0 & |1~8 |Flexible, != other existing LO ODU0s and      |
   |       |ODUflex|    |ODUflexes' TPNs                               |
   +-------+-------+----+----------------------------------------------+
   |       | ODU1  |1~16|Flexible, != other existing LO ODU1s' TPNs    |
   |       +-------+----+----------------------------------------------+
   |       | ODU2  |1~4 |Flexible, != other existing LO ODU2s' TPNs    |
   | ODU3  +-------+----+----------------------------------------------+
   |       |ODU0 & |    |Flexible, != other existing LO ODU0s and      |
   |       |ODU2e &|1~32|ODU2es and ODUflexes' TPNs                    |
   |       |ODUflex|    |                                              |
   +-------+-------+----+----------------------------------------------+
   | ODU4  |Any ODU|1~80|Flexible, != ANY other existing LO ODUs' TPNs |
   +-------+-------+----+----------------------------------------------+

   Note that in the case of "Flexible", the value of TPN is not
   corresponding to the TS number as per [G709-V3].


Zhang                  Expires September 2012                [Page 11]


draft-ietf-ccamp-gmpls-signaling-g709v3-02.txt              March 2012


   Length (12 bits): indicates the number of bit of the Bit Map field,
   i.e., the total number of TS in the HO ODUk link.

   In case of an ODUk mapped into OTUk, there is no need to indicate
   which tributary slots will be used, so the length field MUST be set
   to 0.

   Bit Map (variable): indicates which tributary slots in HO ODUk that
   the LO ODUj will be multiplexed into. The sequence of the Bit Map is
   consistent with the sequence of the tributary slots in HO ODUk. Each
   bit in the bit map represents the corresponding tributary slot in HO
   ODUk with a value of 1 or 0 indicating whether the tributary slot
   will be used by LO ODUj or not.

   Padded bits are added behind the Bit Map to make the whole label a
   multiple of four bytes if necessary. Padded bit MUST be set to 0 and
   MUST be ignored.

   Note that the Length field in the label format can also be used to
   indicate the TS type of the HO ODUk (i.e., TS granularity at 1.25Gbps
   or 2.5Gbps) since the HO ODUk type can be known from IF_ID RSVP_HOP
   Object. In some cases when there is no LMP (Link Management Protocol)
   or routing to make the two end points of the link to know the TSG,
   the TSG information used by another end can be deduced from the label
   format. For example, for HO ODU2 link, the value of the length filed
   will be 4 or 8, which indicates the TS granularity is 2.5Gbps or
   1.25Gbps, respectively.

6.2. Examples

   The following examples are given in order to illustrate the label
   format described in the previous sections of this document.

   (1) ODUk into OTUk mapping:

   In such conditions, the downstream node along an LSP returns a label
   indicating that the ODUk (k=1, 2, 3, 4) is directly mapped into the
   corresponding OTUk. The following example label indicates an ODU1
   mapped into OTU1.

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |       TPN = 0         |   Reserved    |     Length = 0        |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   (2) ODUj into ODUk multiplexing:


Zhang                  Expires September 2012                [Page 12]


draft-ietf-ccamp-gmpls-signaling-g709v3-02.txt              March 2012


   In such conditions, this label indicates that an ODUj is multiplexed
   into several tributary slots of OPUk and then mapped into OTUk. Some
   instances are shown as follow:

   -  ODU0 into ODU2 Multiplexing:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |       TPN = 2         |   Reserved    |     Length = 8        |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |0 1 0 0 0 0 0 0|             Padded Bits (0)                   |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   This above label indicates an ODU0 multiplexed into the second
   tributary slot of ODU2, wherein there are 8 TS in ODU2 (i.e., the
   type of the tributary slot is 1.25Gbps), and the TPN value is 2.

   -  ODU1 into ODU2 Multiplexing with 1.25Gbps TS granularity:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |       TPN = 1         |   Reserved    |     Length = 8        |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |0 1 0 1 0 0 0 0|             Padded Bits (0)                   |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   This above label indicates an ODU1 multiplexed into the 2nd and the
   4th tributary slot of ODU2, wherein there are 8 TS in ODU2 (i.e., the
   type of the tributary slot is 1.25Gbps), and the TPN value is 1.

   -  ODU2 into ODU3 Multiplexing with 2.5Gbps TS granularity:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |       TPN = 1         |   Reserved    |     Length = 16       |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |0 1 1 0 1 0 1 0 0 0 0 0 0 0 0 0|       Padded Bits (0)         |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   This above label indicates an ODU2 multiplexed into the 2nd, 3rd, 5th
   and 7th tributary slot of ODU3, wherein there are 16 TS in ODU3 (i.e.,
   the type of the tributary slot is 2.5Gbps), and the TPN value is 1.




Zhang                  Expires September 2012                [Page 13]


draft-ietf-ccamp-gmpls-signaling-g709v3-02.txt              March 2012


6.3. Label Distribution Procedure

   This document does not change the existing label distribution
   procedures [RFC4328] for GMPLS except that the new ODUk label MUST be
   processed as follows.

   When a node receives a generalized label request for setting up an
   ODUj LSP from its upstream neighbor node, the node MUST generate an
   ODU label according to the signal type of the requested LSP and the
   free resources (i.e., free tributary slots of ODUk) that will be
   reserved for the LSP, and send the label to its upstream neighbor
   node.

   In case of ODUj to ODUk multiplexing, the node MUST firstly determine
   the size of the Bit Map field according to the signal type and the
   tributary slot type of ODUk, and then set the bits to 1 in the Bit
   Map field corresponding to the reserved tributary slots. The node
   MUST also assign a valid TPN, which does not collide with other TPN
   value used by existing LO ODU connections in the selected HO ODU link,
   and configure the expected multiplex structure identifier (ExMSI)
   using this TPN. Then, the assigned TPN is filled into the label.

   In case of ODUk to OTUk mapping, the node only needs to fill the ODUj
   and the ODUk fields with corresponding values in the label. Other
   bits are reserved and MUST be set to 0.

   In order to process a received ODU label, the node MUST firstly learn
   which ODU signal type is multiplexed or mapped into which ODU signal
   type accordingly to the traffic parameters and the IF_ID RSVP_HOP
   Object in the received message.

   In case of ODUj to ODUk multiplexing, the node MUST retrieve the
   reserved tributary slots in the ODUk by its downstream neighbor node
   according to the position of the bits that are set to 1 in the Bit
   Map field. The node determines the TS type (according to the total TS
   number of the ODUk, or pre-configured TS type), so that the node,
   based on the TS type, can multiplex the ODUj into the ODUk. The node
   MUST also retrieve the TPN value assigned by its downstream neighbor
   node from the label, and fill the TPN into the related MSI byte(s) in
   the OPUk overhead in the data plane, so that the downstream neighbor
   node can check whether the TPN received from the data plane is
   consistent with the ExMSI and determine whether there is any mismatch
   defect.

   In case of ODUk to OTUk mapping, the size of Bit Map field MUST be 0
   and no additional procedure is needed.



Zhang                  Expires September 2012                [Page 14]


draft-ietf-ccamp-gmpls-signaling-g709v3-02.txt              March 2012


   Note that the procedures of other label related objects (e.g.,
   Upstream Label, Label Set) are similar to the one described above.

   Note also that the TPN in the label_ERO MAY not be assigned (i.e.,
   TPN field = 0) if the TPN is requested to be assigned locally.

6.3.1. Notification on Label Error

   When receiving an ODUk label from the neighbor node, the node SHOULD
   check the integrity of the label. An error message containing an
   "Unacceptable label value" indication ([RFC3209]) SHOULD be sent if
   one of the following cases occurs:

   -  Invalid value in the length field.

   -  The selected link only supports 2.5Gbps TS granularity while the
      Length field in the label along with ODUk signal type indicates
      the 1.25Gbps TS granularity;

   -  The label includes an invalid TPN value that breaks the TPN
      assignment rules;

   -  The reserved resources (i.e., the number of "1" in the Bit Map
      field) do not match with the Traffic Parameters.

6.4. Supporting Virtual Concatenation and Multiplication

   As per [RFC6344], the VCGs can be created using Co-Signaled style or
   Multiple LSPs style.

   In case of Co-Signaled style, the explicit ordered list of all labels
   reflects the order of VCG members, which is similar to [RFC4328]. In
   case of multiplexed virtually concatenated signals (NVC > 1), the
   first label indicates the components of the first virtually
   concatenated signal; the second label indicates the components of the
   second virtually concatenated signal; and so on. In case of
   multiplication of multiplexed virtually concatenated signals (MT > 1),
   the first label indicates the components of the first multiplexed
   virtually concatenated signal; the second label indicates components
   of the second multiplexed virtually concatenated signal; and so on.

   In case of Multiple LSPs style, multiple control plane LSPs are
   created with a single VCG and the VCAT Call can be used to associate
   the control plane LSPs. The procedures are similar to section 6 of
   [RFC6344].




Zhang                  Expires September 2012                [Page 15]


draft-ietf-ccamp-gmpls-signaling-g709v3-02.txt              March 2012


7. Supporting Multiplexing Hierarchy

   As described in [OTN-FWK], one ODUj connection can be nested into
   another ODUk (j<k) connection, which forms the multiplexing hierarchy
   in the ODU layer. This is useful if there are some intermediate nodes
   in the network which only support ODUk but not ODUj switching.

   For example, in Figure 2, assume that N3 is a legacy node which only
   supports [G709-V1] and does not support ODU0 switching. If an ODU0
   connection between N1 and N5 is required, then we can create an ODU2
   connection between N2 and N4 (or ODU1 / ODU3 connection, depending on
   policies and the capabilities of the two ends of the connection), and
   nest the ODU0 into the ODU2 connection. In this way, N3 only needs to
   perform ODU2 switching and does not need to be aware of the ODU0
   connection.

      |                                                          |
      |<------------------- ODU0 Connection -------------------->|
      |              |                            |              |
      |              |<---- ODU2 Connection ----->|              |
      |              |                            |              |
   +----+         +----+         +----+         +----+         +----+
   | N1 +---------+ N2 +=========+ N3 +=========+ N4 +---------+ N5 |
   +----+         +----+         +----+         +----+         +----+
         ODU3 link      ODU3 link      ODU3 link      ODU3 link

               Figure 2 - Example of multiplexing hierarchy

   The control plane signaling should support the provisioning of
   hierarchical multiplexing. Two methods are provided below (taking
   Figure 2 as example):

   -  Using the multi-layer network signaling described in [RFC4206],
      [RFC6107] and [RFC6001] (including related modifications, if
      needed). That is, when the signaling message for ODUO connection
      arrives at N2, a new RSVP session between N2 and N4 is triggered
      to create the ODU2 connection. This ODU2 connection is treated as
      a Forwarding Adjacency (FA) after it is created. And then the
      signaling procedure for the ODU0 connection can be continued using
      the resource of the ODU2 FA.

   -  The ODU2 FA-LSP is created in advance based on network planning,
      which is treated as an FA. Then the ODU0 connection can be created
      using the resource of the ODU2 FA. In this case, the ODU2 FA-LSP
      and inner ODU0 connections are created separately.




Zhang                  Expires September 2012                [Page 16]


draft-ietf-ccamp-gmpls-signaling-g709v3-02.txt              March 2012


   For both methods, when creating an FA-LSP(e.g., ODU2 FA-LSP), the
   penultimate hop needs to choose a correct outgoing interface for the
   ODU2 connection, so that the destination node can support
   multiplexing and de-multiplexing LO ODU signal(e.g., ODU0). In order
   to choose a correct outgoing interface for the penultimate hop of the
   FA-LSP, multiplexing capability (i.e., what client signal type that
   can be adapted directly to this FA-LSP) should be carried in the
   signaling to setup this FA-LSP. In addition, when Auto_Negotiation in
   the data plane is not enabled, TS granularity may also be needed.

7.1. ADAPTATION Object

   In order to create ODU FA-LSP (i.e., the server layer LSP) for
   carrying the client LSP, a new object called ADAPTATION Object is
   introduced, with two TLVs defined in this document:

     - Type 1 = Server TSG signaling

     - Type 2 = Hierarchy signaling

   (1) Type=1 - Server TSG TLV

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |        Type = 1 (TSG)         |           Length              |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |     TSG       |                  Reserved                     |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   TSG: Tributary Slot Granularity (8bit): Used for signaling the server
   layer TSG:

            - 0 - Reserved
            - 1 - either 1.25Gbps or 2.5Gbps
            - 2 - 2.5Gbps
            - 3 - 1.25Gbps
            - 4~255 - Reserved

   Where value 1 is used where the fallback procedure at the source end
   of FA is enabled and the default value of 1.25Gbps can be fallen back
   to 2.5Gbps. This means that either 1.25 Gpbs or 2.5 Gbps can be used
   as the server TSG at the sink end of FA.

   Values 2 and 3 are used to signal a 2.5Gbps or 1.25Gbps interfaces
   respectively and there is no chance to modify it.



Zhang                  Expires September 2012                [Page 17]


draft-ietf-ccamp-gmpls-signaling-g709v3-02.txt              March 2012


   Other values are reserved for future extension.

   (2) Type=2 - Hierarchy TLV

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |    Type = 2 (Hierarchy)       |           Length              |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     | LSP Enc. Type |Switching Type |  Signal Type  |   Mapping     |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                                                               |
     |                              ...                              |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     | LSP Enc. Type |Switching Type |  Signal Type  |   Mapping     |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   A Hierarchy TLV for each branch of the client signal multiplexing
   supported by the server LSP MUST be used. Inside each TLV a row for
   each stage of the hierarchy MUST be included.

   A row for the server stage MUST NOT be included as it is already
   signaled via the Traffic Parameters.

   The number of stages is implicitly inferred from the length value.

   The meaning of the fields is defined as follow:

      LSP Encoding Type and Switching Type: These fields can assume any
      value inherited from the Generalized Label Request Object in GMPLS
      signaling, defined in [RFC3471] and following related RFCs and
      drafts.

      Signal Type: In the case of non OTN signal types, this field MUST
      be set to 0, while in the case of OTN signal types if MUST be
      filled accordingly to [RFC4328] and this document.

      Mapping: This field indicates the mapping function used in each
      client-server relationship of the hierarchy. The values of this
      field are listed below:

           Value          Type
           -----         ------
             0            Reserved
             1            AMP
             2            BMP
             3            GMP


Zhang                  Expires September 2012                [Page 18]


draft-ietf-ccamp-gmpls-signaling-g709v3-02.txt              March 2012


             4            GFP-F
             5            GFP-T
           6-255          Reserved

   For example, in order to create ODU3 FA-LSP passing through a set of
   ODU4 links to perform ODU1->ODU2->ODU3 hierarchy, the Hierarchy TLV
   can be used to indicate the ODU2 into ODU3 multiplexing and ODU1 into
   ODU2 multiplexing stages.

     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |    Type = 2 (Hierarchy)       |         Length = 8            |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     | Enc.=12(ODUk) | Switching=101 |  Sig. = ODU2  | Mapping = AMP |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     | Enc.=12(ODUk) | Switching=101 |  Sig. = ODU1  | Mapping = AMP |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+


7.2. ODU FA-LSP Creation

   When creating an ODU FA-LSP, the source node (e.g., node N2 in Figure
   2) can include the ADAPTATION object to specify the desired hierarchy
   capabilities.

   On receiving the Path message, the penultimate node on the FA-LSP
   (e.g., node N3 in Figure 2) MUST select an outgoing link which has
   the ability to carry the requested ODU FA-LSP which can support the
   TS granularity and the multiplexing hierarchy listed in the
   ADAPTATION object at the remote end of the link (Note that such
   remote capability information can be obtained through LMP, routing
   protocol or configuration). Then the penultimate node uses the IF_ID
   RSVP_HOP Object to indicate the selected link for carrying the FA-LSP,
   as described in [RFC3473]. If no link supporting the specified
   hierarchy capabilities, a ParhErr message with Error Code = 38 (LSP
   Hierarchy Issue) and Error Value = y1(new value) MUST be sent back to
   upstream.

   Other intermediate nodes along the FA-LSP don't need to process the
   ADAPTATION object, just forwarding it to the next node in the Path
   message, without any modification.









Zhang                  Expires September 2012                [Page 19]


draft-ietf-ccamp-gmpls-signaling-g709v3-02.txt              March 2012


8. Supporting Hitless Adjustment of ODUflex (GFP)

   [G.7044] describes the procedure of ODUflex (GFP) hitless resizing
   using LCR (Link Connection Resize) and BWR (Bandwidth Resize)
   protocols in OTN data plane.

   For the control plane, signaling messages are required to initiate
   the adjustment procedure. Section 2.5 and Section 4.6.4 of [RFC3209]
   describe how the Share Explicit (SE) style is used in TE network for
   bandwidth increasing and decreasing, which is still applicable for
   triggering the ODUflex (GFP) adjustment procedure in data plane.

   Note that the SE style SHOULD be used at the beginning when creating
   a resizable ODUflex connection (Signal Type = 21). Otherwise an error
   with Error Code "Conflicting reservation style" will be generated
   when performing bandwidth adjustment.

   If any node along the ODUflex connection doesn't support hitless
   resizing, a Notify message with Error Code = x2 and Error Value = y1
   will be sent to the source node. The source node MAY keep the
   connection and treat it as a non resizable ODUflex connection, or MAY
   tear it down, depending on the local policy.

   -  Bandwidth increasing

       In order to increase the bandwidth of an ODUflex (GFP) connection,
       a Path message with SE style (keeping Tunnel ID unchanged and
       assigning a new LSP ID) is sent along the path.

       A downstream node compares the old Traffic Parameters (stored
       locally) with the new one carried in the Path message, to
       determine the number of TS to be added. After choosing and
       reserving new free TS, the downstream node sends back a Resv
       message carrying both the old and new LABEL Objects in the SE
       flow descriptor, so that its upstream neighbor can determine
       which TS are added. And the LCR protocol between each pair of
       neighbor nodes is triggered.

       On the source node, the BWR protocol will be triggered by the
       successful completion of LCR protocols on every hop after Resv
       message is processed. On success of BWR, the source node SHOULD
       send a PathTear message to delete the old control state (i.e.,
       the control state of the ODUflex (GFP) before resizing) on the
       control plane.

   -  Bandwidth decreasing



Zhang                  Expires September 2012                [Page 20]


draft-ietf-ccamp-gmpls-signaling-g709v3-02.txt              March 2012


       The SE style can also be used for ODUflex bandwidth decreasing.
       For each pair of neighbor nodes, the sending and receiving Resv
       message with old and new LABEL Objects will trigger the first
       step of LCR between them to perform LCR handshake. On the source
       node, the BWR protocol will be triggered by the successful
       completion of LCR handshake on every hop after Resv message is
       processed. On success of BWR, the second step of LCR, i.e., link
       connection decrease procedure will be started on every hop of the
       connection.

       Similarly, after completion of bandwidth decreasing, a ResvErr
       message SHOULD be sent to tear down the old control state.

9. Control Plane Backward Compatibility Considerations

   Since the [RFC4328] has been deployed in the network for the nodes
   that support [G709-V1], control plane backward compatibility SHOULD
   be taken into consideration when the new nodes (supporting [G709-V3]
   and RSVP-TE extensions defined in this document) and the legacy nodes
   (supporting [G709-V1] and [RFC4328]) are interworking.

   The backward compatibility needs to be considered only when
   controlling ODU1 or ODU2 or ODU3 connection, because legacy nodes can
   only support these three ODU signal types. In such case, new nodes
   can fall back to use signaling message defined in [RFC4328] when
   detecting legacy node on the path. More detailedly:

   o  When receiving Path message using [RFC4328] (i.e., Switching Type
      = 100), a new node SHOULD follow [RFC4328] to process and reply it.

   o  A source node of an ODU LSP can send Path message using new OTN
      control message (with new Switching Type = 101, TBA by IANA). If
      there is legacy node on the LSP, it will fail to process the
      Generalized Label Request Object because of unknown of the new
      Switching Type, and reply a PathErr message indicating unknown of
      this object. The source node MAY re-signal the Path message using
      [RFC4328], depending on local policies.

   o  Alternatively, if a new node has known that its neighbor only
      supports [RFC4328] in advance (e.g., through manual configuration
      or auto discovery mechanism), the new node MAY act as an RSVP
      agent to translate new RSVP-TE message into old one before sending
      to its neighbor.

   No special compatibility consideration needs to be taken if the
   legacy device has updated its control plane to support this document.



Zhang                  Expires September 2012                [Page 21]


draft-ietf-ccamp-gmpls-signaling-g709v3-02.txt              March 2012


10. Security Considerations

   This document introduces no new security considerations to the
   existing GMPLS signaling protocols. Referring to [RFC3473], further
   details of the specific security measures are provided. Additionally,
   [GMPLS-SEC] provides an overview of security vulnerabilities and
   protection mechanisms for the GMPLS control plane.



11. IANA Considerations

   -  G.709 SENDER_TSPEC and FLOWSPEC objects:

       The traffic parameters, which are carried in the G.709
       SENDER_TSPEC and FLOWSPEC objects, do not require any new object
       class and type based on [RFC4328]:

       o G.709 SENDER_TSPEC Object: Class = 12, C-Type = 5 [RFC4328]

       o G.709 FLOWSPEC Object: Class = 9, C-Type = 5 [RFC4328]

   -  Generalized Label Object:

       The new defined ODU label (Section 6) is a kind of generalized
       label. Therefore, the Class-Num and C-Type of the ODU label is
       the same as that of generalized label described in [RFC3473],
       i.e., Class-Num = 16, C-Type = 2.

   -  ADAPTATION Object:

       New object with Class-Num = xx, C-Type = xx. See Section 7 for
       the detail definition.

   -  Error Code = 38 (LSP Hierarchy Issue, referring to [RFC6107]):

       A new Error Value is added to the Error Code "LSP Hierarchy
       Issue":

       Error Value     Error case
       --------------------------------------------------------------
           y1          Last hop of an ODU FA-LSP doesn't support
                      specified adaption capabilities (Section 7.2).

   -  Error Code = x2:




Zhang                  Expires September 2012                [Page 22]


draft-ietf-ccamp-gmpls-signaling-g709v3-02.txt              March 2012


       New Error Code, indicating errors occurring when controlling a
       resizable ODUflex connection.

       Error Value     Error case
       --------------------------------------------------------------
           y1          Do not support hitless assignment of ODUflex (GFP)
                      (Section 8).



12. References

12.1. Normative References

   [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
             Requirement Levels", BCP 14, RFC 2119, March 1997.

   [RFC4328] D. Papadimitriou, Ed. "Generalized Multi-Protocol Label
             Switching (GMPLS) Signaling Extensions for G.709 Optical
             Transport Networks Control", RFC 4328, Jan 2006.

   [RFC3209] D. Awduche et al, "RSVP-TE: Extensions to RSVP for LSP
             Tunnels", RFC3209, December 2001.

   [RFC3471] Berger, L., Editor, "Generalized Multi-Protocol Label
             Switching (GMPLS) Signaling Functional Description", RFC
             3471, January 2003.

   [RFC3473] L. Berger, Ed., "Generalized Multi-Protocol Label Switching
             (GMPLS) Signaling Resource ReserVation Protocol-Traffic
             Engineering (RSVP-TE) Extensions", RFC 3473, January 2003.

   [RFC3945] Mannie, E., "Generalized Multi-Protocol Label Switching
             (GMPLS) Architecture", RFC 3945, October 2004.

   [RFC6344] G. Bernstein et al, "Operating Virtual Concatenation (VCAT)
             and the Link Capacity Adjustment Scheme (LCAS) with
             Generalized Multi-Protocol Label Switching (GMPLS)",
             RFC6344, August 2011.

   [RFC4206] K. Kompella, Y. Rekhter, Ed., " Label Switched Paths (LSP)
             Hierarchy with Generalized Multi-Protocol Label Switching
             (GMPLS) Traffic Engineering (TE)", RFC 4206, October 2005.

   [RFC6107] K. Shiomoto, A. Farrel, "Procedures for Dynamically
             Signaled Hierarchical Label Switched Paths", RFC6107,
             February 2011.


Zhang                  Expires September 2012                [Page 23]


draft-ietf-ccamp-gmpls-signaling-g709v3-02.txt              March 2012


   [RFC6001] Dimitri Papadimitriou et al, "Generalized Multi-Protocol
             Label Switching (GMPLS) Protocol Extensions for Multi-Layer
             and Multi-Region Networks (MLN/MRN)", RFC6001, February 21,
             2010.

   [OTN-FWK] Fatai Zhang et al, "Framework for GMPLS and PCE Control of
             G.709 Optical Transport Networks", draft-ietf-ccamp-gmpls-
             g709-framework-05.txt, September 9, 2011.

   [OTN-INFO] S. Belotti et al, "Information model for G.709 Optical
             Transport Networks (OTN)", draft-ietf-ccamp-otn-g709-info-
             model-01.txt, September 21, 2011.

   [OTN-OSPF] D. Ceccarelli et al, "Traffic Engineering Extensions to
             OSPF for Generalized MPLS (GMPLS) Control of Evolving G.709
             OTN Networks", draft-ietf-ccamp-gmpls-ospf-g709v3-00.txt,
             October 13, 2011

   [OTN-LMP] Fatai Zhang, Ed., "Link Management Protocol (LMP)
             extensions for G.709 Optical Transport Networks", draft-
             zhang-ccamp-gmpls-g.709-lmp-discovery-04.txt, April 6, 2011.

   [G709-V3] ITU-T, "Interfaces for the Optical Transport Network (OTN)
             ", G.709/Y.1331, December 2009.

   [G709-V3-A2] ITU-T, "Interfaces for the Optical Transport Network
             (OTN) Amendment 2", G.709/y.1331 Amendment 2, April 2011.

12.2. Informative References

   [G709-V1] ITU-T, "Interface for the Optical Transport Network (OTN),"
             G.709 Recommendation (and Amendment 1), February 2001
             (November 2001).

   [G709-V2] ITU-T, "Interface for the Optical Transport Network (OTN),"
             G.709 Recommendation, March 2003.

   [G798-V2] ITU-T, "Characteristics of optical transport network
             hierarchy equipment functional blocks", G.798, December
             2006.

   [G798-V3] ITU-T, "Characteristics of optical transport network
             hierarchy equipment functional blocks", G.798v3, consented
             June 2010.

   [G.7044]  ITU-T, "Hitless adjustment of ODUflex", G.7044 (and
             Amendment 1), February 2012.


Zhang                  Expires September 2012                [Page 24]


draft-ietf-ccamp-gmpls-signaling-g709v3-02.txt              March 2012


   [RFC4506] M. Eisler, Ed., "XDR: External Data Representation
             Standard", RFC 4506, May 2006.

   [IEEE]    "IEEE Standard for Binary Floating-Point Arithmetic",
             ANSI/IEEE Standard 754-1985, Institute of Electrical and
             Electronics Engineers, August 1985.

   [GMPLS-SEC] Fang, L., Ed., "Security Framework for MPLS and GMPLS
             Networks", Work in Progress, October 2009.



13. Contributors

   Jonathan Sadler, Tellabs
   Email: jonathan.sadler@tellabs.com


   Kam LAM, Alcatel-Lucent
   Email: kam.lam@alcatel-lucent.com


   Xiaobing Zi, Huawei Technologies
   Email: zixiaobing@huawei.com


   Francesco Fondelli, Ericsson
   Email: francesco.fondelli@ericsson.com

   Lyndon Ong, Ciena
   Email: lyong@ciena.com

   Biao Lu, infinera
   Email: blu@infinera.com



14. Authors' Addresses

   Fatai Zhang (editor)
   Huawei Technologies
   F3-5-B R&D Center, Huawei Base
   Bantian, Longgang District



Zhang                  Expires September 2012                [Page 25]


draft-ietf-ccamp-gmpls-signaling-g709v3-02.txt              March 2012


   Shenzhen 518129 P.R.China
   Phone: +86-755-28972912
   Email: zhangfatai@huawei.com


   Guoying Zhang
   China Academy of Telecommunication Research of MII
   11 Yue Tan Nan Jie Beijing, P.R.China
   Phone: +86-10-68094272
   Email: zhangguoying@mail.ritt.com.cn


   Sergio Belotti
   Alcatel-Lucent
   Optics CTO
   Via Trento 30 20059 Vimercate (Milano) Italy
   +39 039 6863033
   Email: sergio.belotti@alcatel-lucent.it


   Daniele Ceccarelli
   Ericsson
   Via A. Negrone 1/A
   Genova - Sestri Ponente
   Italy
   Email: daniele.ceccarelli@ericsson.com


   Khuzema Pithewan
   Infinera Corporation
   169, Java Drive
   Sunnyvale, CA-94089,  USA
   Email: kpithewan@infinera.com


   Yi Lin
   Huawei Technologies
   F3-5-B R&D Center, Huawei Base
   Bantian, Longgang District
   Shenzhen 518129 P.R.China
   Phone: +86-755-28972914


Zhang                  Expires September 2012                [Page 26]


draft-ietf-ccamp-gmpls-signaling-g709v3-02.txt              March 2012


   Email: yi.lin@huawei.com



   Yunbin Xu
   China Academy of Telecommunication Research of MII
   11 Yue Tan Nan Jie Beijing, P.R.China
   Phone: +86-10-68094134
   Email: xuyunbin@mail.ritt.com.cn


   Pietro Grandi
   Alcatel-Lucent
   Optics CTO
   Via Trento 30 20059 Vimercate (Milano) Italy
   +39 039 6864930
   Email: pietro_vittorio.grandi@alcatel-lucent.it


   Diego Caviglia
   Ericsson
   Via A. Negrone 1/A
   Genova - Sestri Ponente
   Italy
   Email: diego.caviglia@ericsson.com


   Rajan Rao
   Infinera Corporation
   169, Java Drive
   Sunnyvale, CA-94089
   USA
   Email: rrao@infinera.com


   John E Drake
   Juniper
   Email: jdrake@juniper.net


   Igor Bryskin


Zhang                  Expires September 2012                [Page 27]


draft-ietf-ccamp-gmpls-signaling-g709v3-02.txt              March 2012


   Adva Optical
   EMail: IBryskin@advaoptical.com


15. Acknowledgment

   The authors would like to thank Lou Berger and Deborah Brungard for
   their useful comments to the document.



Intellectual Property

   The IETF Trust takes no position regarding the validity or scope of
   any Intellectual Property Rights or other rights that might be
   claimed to pertain to the implementation or use of the technology
   described in any IETF Document or the extent to which any license
   under such rights might or might not be available; nor does it
   represent that it has made any independent effort to identify any
   such rights.

   Copies of Intellectual Property disclosures made to the IETF
   Secretariat and any assurances of licenses to be made available, or
   the result of an attempt made to obtain a general license or
   permission for the use of such proprietary rights by implementers or
   users of this specification can be obtained from the IETF on-line IPR
   repository at http://www.ietf.org/ipr

   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights that may cover technology that may be required to implement
   any standard or specification contained in an IETF Document. Please
   address the information to the IETF at ietf-ipr@ietf.org.

   The definitive version of an IETF Document is that published by, or
   under the auspices of, the IETF. Versions of IETF Documents that are
   published by third parties, including those that are translated into
   other languages, should not be considered to be definitive versions
   of IETF Documents. The definitive version of these Legal Provisions
   is that published by, or under the auspices of, the IETF. Versions of
   these Legal Provisions that are published by third parties, including
   those that are translated into other languages, should not be
   considered to be definitive versions of these Legal Provisions.

   For the avoidance of doubt, each Contributor to the IETF Standards
   Process licenses each Contribution that he or she makes as part of


Zhang                  Expires September 2012                [Page 28]


draft-ietf-ccamp-gmpls-signaling-g709v3-02.txt              March 2012


   the IETF Standards Process to the IETF Trust pursuant to the
   provisions of RFC 5378. No language to the contrary, or terms,
   conditions or rights that differ from or are inconsistent with the
   rights and licenses granted under RFC 5378, shall have any effect and
   shall be null and void, whether published or posted by such
   Contributor, or included with or in such Contribution.


Disclaimer of Validity

   All IETF Documents and the information contained therein are provided
   on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE
   REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE
   IETF TRUST AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL
   WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY
   WARRANTY THAT THE USE OF THE INFORMATION THEREIN WILL NOT INFRINGE
   ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS
   FOR A PARTICULAR PURPOSE.


Copyright Notice

   Copyright (c) 2010 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.














Zhang                  Expires September 2012                [Page 29]