Softwire Working Group Y. Cui
Internet-Draft Tsinghua University
Intended status: Standards Track I. Farrer
Expires: April 26, 2019 Deutsche Telekom AG
M. Boucadair
Orange
Q. Sun
L. Sun
Tsinghua University
S. Zechlin
Deutsche Telekom AG
R. Asati
Cisco Systems, Inc.
October 23, 2018
YANG Modules for IPv4-in-IPv6 Address plus Port Softwires
draft-ietf-softwire-yang-08
Abstract
This document defines YANG modules for the configuration and
operation of IPv4-in-IPv6 softwire Border Relays and Customer
Premises Equipment for the Lightweight 4over6, MAP-E, and MAP-T
softwire mechanisms.
Editorial Note (To be removed by RFC Editor)
Please update these statements within this document with the RFC
number to be assigned to this document:
o "This version of this YANG module is part of RFC XXXX;"
o "RFC XXXX: YANG Modules for IPv4-in-IPv6 Address plus Port
Softwires";
o "reference: RFC XXXX"
Please update the "revision" date of the YANG module.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Cui, et al. Expires April 26, 2019 [Page 1]
Internet-Draft YANG Modules for A+P Softwires October 2018
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on April 26, 2019.
Copyright Notice
Copyright (c) 2018 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(https://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1. Terminology . . . . . . . . . . . . . . . . . . . . . . . 3
2. Overview of the Modules . . . . . . . . . . . . . . . . . . . 4
2.1. Overall Structure . . . . . . . . . . . . . . . . . . . . 4
2.2. Additional Components Configuration . . . . . . . . . . . 5
3. Softwire CE YANG Tree Diagram . . . . . . . . . . . . . . . . 6
3.1. CE Tree Diagram . . . . . . . . . . . . . . . . . . . . . 6
3.2. Softwire CE Tree Diagram Description . . . . . . . . . . 8
4. Softwire BR YANG Tree Diagram . . . . . . . . . . . . . . . . 9
4.1. BR Tree Diagram . . . . . . . . . . . . . . . . . . . . . 9
4.2. Softwire BR Tree Diagram Description . . . . . . . . . . 13
5. IANA Tunnel Type YANG Module . . . . . . . . . . . . . . . . 13
6. Tunnel Extension to the Interface YANG Module . . . . . . . . 16
7. Softwire CE YANG Module . . . . . . . . . . . . . . . . . . . 18
8. BR Softwire YANG Module . . . . . . . . . . . . . . . . . . . 24
9. Common Softwire Element Groups YANG Module . . . . . . . . . 36
10. Security Considerations . . . . . . . . . . . . . . . . . . . 44
11. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 45
12. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 47
13. Contributors . . . . . . . . . . . . . . . . . . . . . . . . 47
14. References . . . . . . . . . . . . . . . . . . . . . . . . . 47
14.1. Normative References . . . . . . . . . . . . . . . . . . 47
Cui, et al. Expires April 26, 2019 [Page 2]
Internet-Draft YANG Modules for A+P Softwires October 2018
14.2. Informative References . . . . . . . . . . . . . . . . . 49
Appendix A. Configutation Examples . . . . . . . . . . . . . . . 50
A.1. Configuration Example for a lw4o6 BR Binding-Table . . . 50
A.2. Configuration Example for a MAP-E BR . . . . . . . . . . 51
A.3. lw4o6 CE Configuration Example . . . . . . . . . . . . . 52
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 56
1. Introduction
The IETF softwire working group has developed several IPv4-in-IPv6
softwire mechanisms to address various deployment contexts and
constraints. As a companion to the architectural specification
documents, this document focuses on the provisioning of address plus
port (A+P) softwire functional elements: Border Routers (BRs) and
Customer Premises Equipment (CEs, a.k.a., CPE). The softwire
mechanisms covered in this document are Lightweight 4 over 6
[RFC7596], MAP-E [RFC7597], and MAP-T [RFC7599].
This document focuses on A+P mechanisms; the reader can refer to
[I-D.ietf-softwire-dslite-yang] for a YANG module for DS-Lite
[RFC6333].
This document defines YANG data modules [RFC7950] that can be used to
configure and manage A+P softwire elements using the NETCONF protocol
[RFC6241] for:
o Configuration
o Operational State
o Notifications
1.1. Terminology
The reader should be familiar with the concepts and terms defined in
[RFC7596], [RFC7597], [RFC7599], and the YANG data modelling language
defined in [RFC7950].
The adopts the Network Management Datastore Architecture (NMDA)
[RFC8342]. The meaning of the symbols in tree diagrams is defined in
[RFC8340].
The document uses BR to refer to MAP BR [RFC7597] or Lightweight
4over6 BR [RFC7596].
For simplicity, "algorithm" is used to refer to "mapping algorithm"
[RFC7597].
Cui, et al. Expires April 26, 2019 [Page 3]
Internet-Draft YANG Modules for A+P Softwires October 2018
2. Overview of the Modules
2.1. Overall Structure
This document specifies the initial version of an IANA-maintained
module to identify a collection of tunnel types assigned by IANA
(Section 5). Furthermore, the document augments the Interface YANG
module [RFC8343] with a new parameter which is meant to indicate the
type of a given tunnel (Section 6). The tree structure of this
extension is shown below:
module: ietf-interface-tunnel
augment /if:interfaces/if:interface:
+--rw tunnel-type? identityref
Moreover, the document defines the following two YANG data modules
for the configuration and monitoring of softwire functional elements:
ietf-softwire-ce Provides configuration and monitoring for
softwire CE element. This module is defined as
augments to the interface YANG module
[RFC8343].
ietf-softwire-br Provides configuration and monitoring for
softwire BR element.
In addition, the following module is defined:
ietf-softwire-common Contains groups of common functions that are
imported into the CE and BR modules.
This approach has been taken so that the various modules can be
easily extended to support additional softwire mechanisms, if
required.
Within the BR and CE modules, the YANG "feature" statement is used to
distinguish which of the different softwire mechanism(s) is relevant
for a specific element's configuration. For each module, a choice
statement 'ce-type' is included for either 'binding' or 'algorithm'.
'Binding' is used for configuring Lightweight 4over6, whereas
'algorithm' is used for configuring MAP-T or MAP-E.
In the 'algo-instances' container, a choice statement 'data-plane' is
included to specify MAP-E (encapsulation) or MAP-T (translation).
Table 1 shows how these choices are used to indicate the desired
softwire mechanism:
Cui, et al. Expires April 26, 2019 [Page 4]
Internet-Draft YANG Modules for A+P Softwires October 2018
+--------------------+-----------+---------------+
| S46 Mechanism | ce-type? | data-plane? |
+--------------------+-----------+---------------+
| Lightweight 4over6 | binding | n/a |
| MAP-E | algorithm | encapsulation |
| MAP-T | algorithm | translation |
+--------------------+-----------+---------------+
Table 1: Softwire Mechanism Choice Statement Enumeration
NETCONF notifications are also included.
Note: Earlier versions of this specification combined the softwire
mechanisms by their associated technologies rather than their
function in the architecture. As the document was revised, it
became apparent that dividing the modules by their role in the
architecture (CE or BR) was a better approach as this follows the
intended function and existing implementation approaches more
closely.
2.2. Additional Components Configuration
The softwire modules only aim to provide configuration relevant for
softwires. In order to fully provision a CE element, the following
may also be necessary:
o IPv6 forwarding and routing configuration, to enable CE to obtain
one or more IPv6 prefixes for softwire usage. A YANG module for
routing management is described in [RFC8349].
o IPv4 routing configuration, to add one or more IPv4 destination
prefix(es) reachable via the configured softwire. A YANG module
for routing management is described in [RFC8349].
o Stateful NAT44/NAPT management, to optionally specify a port set
(Port Set Identifier (PSID)) along with its length. A YANG module
for NAT management is described in [I-D.ietf-opsawg-nat-yang].
o Stateless NAT46 management, required by softwire translation based
mechanisms (i.e., the assignment of a Network-Specific Prefix to
use for IPv4/IPv6 translation). A YANG module for NAT management
is described in [I-D.ietf-opsawg-nat-yang].
As YANG modules for the above functions are already defined in other
documents, their functionality is not duplicated here and they should
be referred to, as needed. Appendix A.3 provides XML examples of how
these modules can be used together.
Cui, et al. Expires April 26, 2019 [Page 5]
Internet-Draft YANG Modules for A+P Softwires October 2018
The CE must already have minimal IPv6 configuration in place so it is
reachable by the NETCONF client to obtain softwire configuration. If
additional IPv6 specific configuration is necessary, the YANG modules
defined in [RFC8344] and [RFC8349] may be used.
3. Softwire CE YANG Tree Diagram
3.1. CE Tree Diagram
The CE module provides configuration and monitoring for all of the
softwire mechanisms covered in this document (i.e., Lightweight
4over6, MAP-E, and MAP-T).
This module augments "ietf-interfaces", defined in [RFC8343] with an
entry for the softwire. This entry can be referenced to configure
IPv4 forwarding features for the element.
Figure 1 describes the tree structure of the softwire CE YANG module.
module: ietf-softwire-ce
augment /if:interfaces/if:interface:
+--rw softwire-payload-mtu? uint16
+--rw softwire-path-mru? uint16
+--rw (ce-type)?
+--:(binding) {binding-mode}?
| +--rw binding-ipv6info? union
| +--rw br-ipv6-addr inet:ipv6-address
+--:(algo) {map-e or map-t}?
+--rw algo-instances
+--rw algo-instance* [id]
+--rw id uint32
+--rw enable? boolean
+--rw algo-versioning
| +--rw version? uint64
| +--rw date? yang:date-and-time
+--rw name? string
+--rw (data-plane)?
| +--:(encapsulation) {map-e}?
| | +--rw br-ipv6-addr inet:ipv6-address
| +--:(translation) {map-t}?
| +--rw dmr-ipv6-prefix? inet:ipv6-prefix
+--rw ea-len uint8
+--rw rule-ipv6-prefix inet:ipv6-prefix
+--rw rule-ipv4-prefix inet:ipv4-prefix
+--rw forwarding boolean
augment /if:interfaces/if:interface/if:statistics:
+--ro sent-ipv4-packets?
| yang:zero-based-counter64
Cui, et al. Expires April 26, 2019 [Page 6]
Internet-Draft YANG Modules for A+P Softwires October 2018
+--ro sent-ipv4-bytes?
| yang:zero-based-counter64
+--ro sent-ipv6-packets?
| yang:zero-based-counter64
+--ro sent-ipv6-bytes?
| yang:zero-based-counter64
+--ro rcvd-ipv4-packets?
| yang:zero-based-counter64
+--ro rcvd-ipv4-bytes?
| yang:zero-based-counter64
+--ro rcvd-ipv6-packets?
| yang:zero-based-counter64
+--ro rcvd-ipv6-bytes?
| yang:zero-based-counter64
+--ro dropped-ipv4-packets?
| yang:zero-based-counter64
+--ro dropped-ipv4-bytes?
| yang:zero-based-counter64
+--ro dropped-ipv6-packets?
| yang:zero-based-counter64
+--ro dropped-ipv6-bytes?
| yang:zero-based-counter64
+--ro dropped-ipv4-fragments?
| yang:zero-based-counter64
+--ro dropped-ipv4-fragment-bytes?
| yang:zero-based-counter64
+--ro ipv6-fragments-reassembled?
| yang:zero-based-counter64
+--ro ipv6-fragments-bytes-reassembled?
| yang:zero-based-counter64
+--ro out-icmpv4-error-packets?
| yang:zero-based-counter64
+--ro out-icmpv4-error-bytes?
| yang:zero-based-counter64
+--ro out-icmpv6-error-packets?
| yang:zero-based-counter64
+--ro out-icmpv6-error-bytes?
yang:zero-based-counter64
notifications:
+---n softwire-ce-event {binding-mode}?
+--ro ce-binding-ipv6-addr-change inet:ipv6-address
Figure 1: Softwire CE YANG Tree Diagram
Cui, et al. Expires April 26, 2019 [Page 7]
Internet-Draft YANG Modules for A+P Softwires October 2018
3.2. Softwire CE Tree Diagram Description
Additional information related to the operation of a CE element is
provided below:
o softwire-payload-mtu: optionally used to set the IPv4 MTU for the
softwire. Needed if the softwire implementation is unable to
correctly calculate the correct IPv4 Maximum Transit Unit (MTU)
size automatically.
o softwire-path-mru: optionally used to set the maximum IPv6
softwire packet size that can be received, including the
encapsulation/translation overhead. Needed if the softwire
implementation is unable to correctly calculate the correct IPv4
Maximum Receive Unit (MRU) size automatically.
o ce-type: provides a choice statement allowing the binding or
algorithmic softwire mechanisms to be selected.
Further details relevant to binding softwire elements are:
o binding-ipv6info: used to set the IPv6 binding prefix type to
identify which IPv6 address to use as the tunnel source. It can
be 'ipv6-prefix' or 'ipv6-address'.
o br-ipv6-addr: defines the IPv6 address of the remote BR.
Additional details relevant to some of the important algorithmic
elements are provided below:
o algo-versioning: optionally used to add an incremental version
number and/or timestamp to the algorithm. This can be used for
logging/data retention purposes [RFC7422]. The version number is
incremented and a new timestamp value written whenever a change is
made to the algorithm or a new instance is created.
o forwarding: specifies whether the rule can be used as a Forward
Mapping Rule (FMR). If not set, this rule is a Basic Mapping Rule
(BMR) only and must not be used for forwarding. Refer to
Section 4.1 of [RFC7598].
o ea-len: used to set the length of the Embedded-Address (EA), which
is defined in the mapping rule for a MAP domain.
o data-plane: provides a choice statement for either encapsulation
(MAP-E) or translation (MAP-T).
o br-ipv6-addr: defines the IPv6 address of the BR. This
Cui, et al. Expires April 26, 2019 [Page 8]
Internet-Draft YANG Modules for A+P Softwires October 2018
information is valid for MAP-E.
o dmr-ipv6-prefix: defines the Default Mapping Rule (DMR) IPv6
prefix of the BR. This information is valid for MAP-T.
Additional information on the notification node is listed below:
o ce-binding-ipv6-addr-change: if the CE's binding IPv6 address
changes for any reason, the NETCONF client will be notified.
4. Softwire BR YANG Tree Diagram
4.1. BR Tree Diagram
The BR YANG module provides configuration and monitoring for all of
the softwire mechanisms covered in this document (i.e., Lightweight
4over6, MAP-E, and MAP-T).
Figure 2 provides the tree structure of this module.
module: ietf-softwire-br
+--rw br-instances
+--rw (br-type)?
+--:(binding) {binding-mode}?
| +--rw binding
| +--rw bind-instances* [id]
| +--rw binding-table-versioning
| | +--rw version? uint64
| | +--rw date? yang:date-and-time
| +--rw id uint32
| +--rw name? string
| +--rw softwire-num-max uint32
| +--rw softwire-payload-mtu uint16
| +--rw softwire-path-mru uint16
| +--rw enable-hairpinning? boolean
| +--rw binding-table
| | +--rw binding-entry* [binding-ipv6info]
| | +--rw binding-ipv6info union
| | +--rw binding-ipv4-addr?
| | | inet:ipv4-address
| | +--rw port-set
| | | +--rw psid-offset? uint8
| | | +--rw psid-len uint8
| | | +--rw psid uint16
| | +--rw br-ipv6-addr?
| | inet:ipv6-address
| +--rw icmp-policy
| | +--rw icmpv4-errors
Cui, et al. Expires April 26, 2019 [Page 9]
Internet-Draft YANG Modules for A+P Softwires October 2018
| | | +--rw allow-incoming-icmpv4? boolean
| | | +--rw icmpv4-rate? uint32
| | | +--rw generate-icmpv4-errors? boolean
| | +--rw icmpv6-errors
| | +--rw generate-icmpv6-errors? boolean
| | +--rw icmpv6-rate? uint32
| +--ro traffic-stat
| +--ro discontinuity-time yang:date-and-time
| +--ro sent-ipv4-packets?
| | yang:zero-based-counter64
| +--ro sent-ipv4-bytes?
| | yang:zero-based-counter64
| +--ro sent-ipv6-packets?
| | yang:zero-based-counter64
| +--ro sent-ipv6-bytes?
| | yang:zero-based-counter64
| +--ro rcvd-ipv4-packets?
| | yang:zero-based-counter64
| +--ro rcvd-ipv4-bytes?
| | yang:zero-based-counter64
| +--ro rcvd-ipv6-packets?
| | yang:zero-based-counter64
| +--ro rcvd-ipv6-bytes?
| | yang:zero-based-counter64
| +--ro dropped-ipv4-packets?
| | yang:zero-based-counter64
| +--ro dropped-ipv4-bytes?
| | yang:zero-based-counter64
| +--ro dropped-ipv6-packets?
| | yang:zero-based-counter64
| +--ro dropped-ipv6-bytes?
| | yang:zero-based-counter64
| +--ro dropped-ipv4-fragments?
| | yang:zero-based-counter64
| +--ro dropped-ipv4-fragment-bytes?
| | yang:zero-based-counter64
| +--ro ipv6-fragments-reassembled?
| | yang:zero-based-counter64
| +--ro ipv6-fragments-bytes-reassembled?
| | yang:zero-based-counter64
| +--ro out-icmpv4-error-packets?
| | yang:zero-based-counter64
| +--ro out-icmpv4-error-bytes?
| | yang:zero-based-counter64
| +--ro out-icmpv6-error-packets?
| | yang:zero-based-counter64
| +--ro out-icmpv6-error-bytes?
| | yang:zero-based-counter64
Cui, et al. Expires April 26, 2019 [Page 10]
Internet-Draft YANG Modules for A+P Softwires October 2018
| +--ro dropped-icmpv4-packets?
| | yang:zero-based-counter64
| +--ro dropped-icmpv4-bytes?
| | yang:zero-based-counter64
| +--ro hairpin-ipv4-packets?
| | yang:zero-based-counter64
| +--ro hairpin-ipv4-bytes?
| | yang:zero-based-counter64
| +--ro active-softwire-num?
| uint32
+--:(algo) {map-e or map-t}?
+--rw algorithm
+--rw algo-instances* [id]
+--rw id uint32
+--rw enable? boolean
+--rw algo-versioning
| +--rw version? uint64
| +--rw date? yang:date-and-time
+--rw name? string
+--rw (data-plane)?
| +--:(encapsulation) {map-e}?
| | +--rw br-ipv6-addr inet:ipv6-address
| +--:(translation) {map-t}?
| +--rw dmr-ipv6-prefix? inet:ipv6-prefix
+--rw ea-len uint8
+--rw rule-ipv6-prefix inet:ipv6-prefix
+--rw rule-ipv4-prefix inet:ipv4-prefix
+--rw forwarding boolean
+--rw port-set
| +--rw psid-offset? uint8
| +--rw psid-len uint8
| +--rw psid uint16
+--ro traffic-stat
+--ro discontinuity-time yang:date-and-time
+--ro sent-ipv4-packets?
| yang:zero-based-counter64
+--ro sent-ipv4-bytes?
| yang:zero-based-counter64
+--ro sent-ipv6-packets?
| yang:zero-based-counter64
+--ro sent-ipv6-bytes?
| yang:zero-based-counter64
+--ro rcvd-ipv4-packets?
| yang:zero-based-counter64
+--ro rcvd-ipv4-bytes?
| yang:zero-based-counter64
+--ro rcvd-ipv6-packets?
| yang:zero-based-counter64
Cui, et al. Expires April 26, 2019 [Page 11]
Internet-Draft YANG Modules for A+P Softwires October 2018
+--ro rcvd-ipv6-bytes?
| yang:zero-based-counter64
+--ro dropped-ipv4-packets?
| yang:zero-based-counter64
+--ro dropped-ipv4-bytes?
| yang:zero-based-counter64
+--ro dropped-ipv6-packets?
| yang:zero-based-counter64
+--ro dropped-ipv6-bytes?
| yang:zero-based-counter64
+--ro dropped-ipv4-fragments?
| yang:zero-based-counter64
+--ro dropped-ipv4-fragment-bytes?
| yang:zero-based-counter64
+--ro ipv6-fragments-reassembled?
| yang:zero-based-counter64
+--ro ipv6-fragments-bytes-reassembled?
| yang:zero-based-counter64
+--ro out-icmpv4-error-packets?
| yang:zero-based-counter64
+--ro out-icmpv4-error-bytes?
| yang:zero-based-counter64
+--ro out-icmpv6-error-packets?
| yang:zero-based-counter64
+--ro out-icmpv6-error-bytes?
yang:zero-based-counter64
notifications:
+---n softwire-binding-instance-event {binding-mode}?
| +--ro bind-id?
| | -> /br-instances/binding/bind-instances/id
| +--ro invalid-entry* leafref
| +--ro added-entry* inet:ipv6-address
| +--ro modified-entry* leafref
+---n softwire-algorithm-instance-event {map-e, map-t}?
+--ro algo-id
| -> /br-instances/algorithm/algo-instances/id
+--ro invalid-entry-id*
| -> /br-instances/algorithm/algo-instances/id
+--ro added-entry*
| -> /br-instances/algorithm/algo-instances/id
+--ro modified-entry*
-> /br-instances/algorithm/algo-instances/id
Figure 2: Softwire BR YANG Tree
Cui, et al. Expires April 26, 2019 [Page 12]
Internet-Draft YANG Modules for A+P Softwires October 2018
4.2. Softwire BR Tree Diagram Description
The descriptions for leaves which are common with the CE module are
provided in Section 3.2. Descriptions for additional elements are
provided below:
o binding-table-versioning: optionally used to add an incremental
version number and/or timestamp to the binding table. This can be
used for logging or data retention purposes [RFC7422]. The
version number is incremented and a new timestamp value written
whenever a change is made to the contents of the binding table or
a new binding table list is created.
o binding-entry: used to define the binding relationship between
3-tuples {lwB4's IPv6 address/prefix, the allocated IPv4 address,
restricted port-set}. For detail information, please refer to
[RFC7596].
o softwire-num-max: used to set the maximum number of softwire
binding rules that can be created on the lw4o6 element
simultaneously.
o active-softwire-num: holds the number of softwires currently
provisioned on the element.
Additional information on some of the important notification nodes is
listed below:
o invalid-entry, added-entry, modified-entry: used to notify the
NETCONF client that a specific binding entry or MAP rule has
expired, been invalidated, added, or modified.
5. IANA Tunnel Type YANG Module
<CODE BEGINS> file "iana-tunnel-type@2018-10-19.yang"
module iana-tunnel-type {
yang-version 1.1;
namespace "urn:ietf:params:xml:ns:yang:iana-tunnel-type";
prefix iana-tunnel-type;
import iana-if-type {
prefix ift;
reference
"RFC 7224: IANA Interface Type YANG Module";
}
organization
Cui, et al. Expires April 26, 2019 [Page 13]
Internet-Draft YANG Modules for A+P Softwires October 2018
"IANA";
contact
"Internet Assigned Numbers Authority
Postal: ICANN
12025 Waterfront Drive, Suite 300
Los Angeles, CA 90094-2536
United States of America
Tel: +1 310 301 5800
<mailto:iana@iana.org>";
description
"This module contains a collection of YANG data types defined
by IANA and used for tunnel types.
Copyright (c) 2018 IETF Trust and the persons identified as
authors of the code. All rights reserved.
Redistribution and use in source and binary forms, with or
without modification, is permitted pursuant to, and subject
to the license terms contained in, the Simplified BSD License
set forth in Section 4.c of the IETF Trust's Legal Provisions
Relating to IETF Documents
(http://trustee.ietf.org/license-info).
This version of this YANG module is part of RFC XXXX; see
the RFC itself for full legal notices.";
revision 2018-10-19 {
description
"Initial revision.";
reference
"RFC XXXX: YANG Modules for IPv4-in-IPv6 Address plus Port
Softwires";
}
identity other {
base ift:tunnel;
description
"None of the following values.";
}
identity direct {
base ift:tunnel;
description
"No intermediate header.";
}
identity gre {
base ift:tunnel;
Cui, et al. Expires April 26, 2019 [Page 14]
Internet-Draft YANG Modules for A+P Softwires October 2018
description
"GRE encapsulation.";
}
identity minimal {
base ift:tunnel;
description
"Minimal encapsulation.";
}
identity l2tp {
base ift:tunnel;
description
"L2TP encapsulation.";
}
identity pptp {
base ift:tunnel;
description
"PPTP encapsulation.";
}
identity l2f {
base ift:tunnel;
description
"L2F encapsulation.";
}
identity udp {
base ift:tunnel;
description
"UDP encapsulation.";
}
identity atmp {
base ift:tunnel;
description
"ATMP encapsulation.";
}
identity msdp {
base ift:tunnel;
description
"MSDP encapsulation.";
}
identity sixtofour {
base ift:tunnel;
description
"6to4 encapsulation.";
}
identity sixoverfour {
base ift:tunnel;
description
"6over4 encapsulation.";
}
Cui, et al. Expires April 26, 2019 [Page 15]
Internet-Draft YANG Modules for A+P Softwires October 2018
identity isatap {
base ift:tunnel;
description
"ISATAP encapsulation.";
}
identity teredo {
base ift:tunnel;
description
"Teredo encapsulation.";
}
identity iphttps {
base ift:tunnel;
description
"IP over HTTPS.";
}
identity softwiremesh {
base ift:tunnel;
description
"softwire mesh tunnel.";
}
identity dslite {
base ift:tunnel;
description
"DS-Lite tunnel.";
}
// TBD: register this value.
identity aplusp {
base ift:tunnel;
description
"A+P encapsulation.";
}
}
<CODE ENDS>
6. Tunnel Extension to the Interface YANG Module
The ietf-interface-tunnel module imports the modules defined in
[RFC7224] and [RFC8343].
<CODE BEGINS> file "ietf-interface-tunnel@2018-10-19.yang"
module ietf-interface-tunnel {
yang-version 1.1;
namespace "urn:ietf:params:xml:ns:yang:ietf-interface-tunnel";
prefix ietf-interface-tunnel;
import ietf-interfaces {
Cui, et al. Expires April 26, 2019 [Page 16]
Internet-Draft YANG Modules for A+P Softwires October 2018
prefix if;
reference
"RFC 8343: A YANG Data Model for Interface Management";
}
import iana-if-type {
prefix ift;
reference
"RFC 7224: IANA Interface Type YANG Module";
}
organization "IETF xxx Working Group";
contact
"WG Web: <https://datatracker.ietf.org/wg/softwires/>
WG List: <mailto:softwire@ietf.org>
Editor: Mohamed Boucadair
<mailto:mohamed.boucadair@orange.com>";
description
"This module is a YANG module for associating a tunnel type with
tunnel interfaces.
Copyright (c) 2018 IETF Trust and the persons identified as
authors of the code. All rights reserved.
Redistribution and use in source and binary forms, with or
without modification, is permitted pursuant to, and subject
to the license terms contained in, the Simplified BSD License
set forth in Section 4.c of the IETF Trust's Legal Provisions
Relating to IETF Documents
(http://trustee.ietf.org/license-info).
This version of this YANG module is part of RFC XXXX; see
the RFC itself for full legal notices.";
revision 2018-10-19 {
description
"Initial revision.";
reference
"RFC XXXX: YANG Modules for IPv4-in-IPv6 Address plus Port
Softwires";
}
augment "/if:interfaces/if:interface" {
when 'derived-from(if:type, "ift:tunnel")';
Cui, et al. Expires April 26, 2019 [Page 17]
Internet-Draft YANG Modules for A+P Softwires October 2018
description
"Augments Interface module with tunnel-specific parameters.
IANA interface types are maintained at this registry:
https://www.iana.org/assignments/ianaiftype-mib/ianaiftype-mib.
tunnel (131), -- Encapsulation interface";
leaf tunnel-type {
type identityref {
base ift:tunnel;
}
description
"Indicates the type of the tunnel. It corresponds
to the IANAtunnelType.
IANA tunnel types are maintained at this registry:
https://www.iana.org/assignments/ianaiftype-mib/ianaiftype-mib.";
}
}
}
<CODE ENDS>
7. Softwire CE YANG Module
This module imports the modules defined in [RFC6991], [RFC8343], and
[RFC7224]. It also imports the 'ietf-softwire-common' module.
<CODE BEGINS>file "ietf-softwire-ce@2018-10-19.yang"
module ietf-softwire-ce {
yang-version 1.1;
namespace "urn:ietf:params:xml:ns:yang:ietf-softwire-ce";
prefix "softwire-ce";
import ietf-inet-types {
prefix inet;
reference
"Section 4 of RFC 6991";
}
/*import ietf-yang-types {
prefix yang;
reference
"Section 3 of RFC 6991";
}*/
import ietf-interfaces {
Cui, et al. Expires April 26, 2019 [Page 18]
Internet-Draft YANG Modules for A+P Softwires October 2018
prefix if;
reference
"RFC 8343: A YANG Data Model for Interface Management";
}
import ietf-softwire-common {
prefix softwire-common;
reference
"RFC XXXX: YANG Modules for IPv4-in-IPv6 Address plus Port
Softwires";
}
import iana-tunnel-type {
prefix iana-tunnel-type;
reference
"RFC XXXX: YANG Modules for IPv4-in-IPv6 Address plus Port
Softwires";
}
import ietf-interface-tunnel {
prefix ift;
reference
"RFC XXXX: YANG Modules for IPv4-in-IPv6 Address plus Port
Softwires";
}
organization
"IETF Softwire Working Group";
contact
"WG Web: <https://datatracker.ietf.org/wg/softwire/>
WG List: <mailto:softwire@ietf.org>
Author: Qi Sun
<mailto:sunqi.ietf@gmail.com>
Author: Linhui Sun
<mailto:lh.sunlinh@gmail.com>
Author: Yong Cui
<mailto:yong@csnet1.cs.tsinghua.edu.cn>
Author: Ian Farrer
<mailto:ian.farrer@telekom.de>
Author: Sladjana Zoric
<mailto:sladjana.zoric@telekom.de>
Author: Mohamed Boucadair
Cui, et al. Expires April 26, 2019 [Page 19]
Internet-Draft YANG Modules for A+P Softwires October 2018
<mailto:mohamed.boucadair@orange.com>
Author: Rajiv
<mailto:Asati rajiva@cisco.com>";
description
"This document defines a YANG data module for the configuration and
management of A+P Softwire Customer Premises Equipment (CEs). It
covers Lightweight 4over6, MAP-E, and MAP-T mechanisms.
Copyright (c) 2018 IETF Trust and the persons identified as
authors of the code. All rights reserved.
Redistribution and use in source and binary forms, with or
without modification, is permitted pursuant to, and subject
to the license terms contained in, the Simplified BSD License
set forth in Section 4.c of the IETF Trust's Legal Provisions
Relating to IETF Documents
(http://trustee.ietf.org/license-info).
This version of this YANG module is part of RFC XXXX; see
the RFC itself for full legal notices.";
revision 2018-10-19 {
description
"Initial revision.";
reference
"RFC XXXX: YANG Modules for IPv4-in-IPv6 Address plus Port
Softwires";
}
/*
* Features
*/
feature binding-mode {
description
"Binding is used for configuring the Lightweight 4over6 mechanism.
Binding based softwire mechanisms are IPv4-over-IPv6 tunnelling
transition mechanisms specifically intended for complete
independence between the IPv6 subnet prefix (and IPv6 address)
and IPv4 address, with or without IPv4 address sharing.
This is accomplished by maintaining state for each softwire
(per-subscriber state) in the central Border Relay (BR) and using
a hub-and-spoke forwarding architecture. In order to delegate the
NAPT function and achieve IPv4 address sharing, port-restricted
Cui, et al. Expires April 26, 2019 [Page 20]
Internet-Draft YANG Modules for A+P Softwires October 2018
IPv4 addresses needs to be allocated to CEs.
This feature indicates that the instance functions as a binding
based softwire instance.";
reference
"RFC7596: Lightweight 4over6: An Extension to the Dual-Stack Lite
Architecture
RFC7597: Mapping of Address and Port with Encapsulation (MAP-E)
RFC7599: Mapping of Address and Port using Translation (MAP-T)";
}
feature map-e {
description
"MAP-E is an IPv6 transition mechanism for transporting IPv4
packets across an IPv6 network using IP encapsulation. MAP-E
allows for a reduction of the amount of centralized state using
rules to express IPv4/IPv6 address mappings. This introduces an
algorithmic relationship between the IPv6 subnet and IPv4 address.
This feature indicates that the instance functions as a MAP-E.";
reference
"RFC7597: Mapping of Address and Port with Encapsulation (MAP-E)";
}
feature map-t {
description
"MAP-T is an IPv6 transition mechanism for transporting IPv4
packets across an IPv6 network using IP translation. It leverages
a double stateless NAT64 based solution as well as the stateless
algorithmic address & transport layer port mapping algorithm
defined for MAP-E.
This feature indicates that the instance functions as a MAP-T
instance.";
reference
"RFC7599: Mapping of Address and Port using Translation (MAP-T)";
}
// Binding Entry
grouping binding-entry {
description
"The binding BR (Border Relay) maintains an address binding table
that contains the binding between the CE's IPv6 address,
the allocated IPv4 address and restricted port-set.";
Cui, et al. Expires April 26, 2019 [Page 21]
Internet-Draft YANG Modules for A+P Softwires October 2018
leaf binding-ipv6info {
type union {
type inet:ipv6-address;
type inet:ipv6-prefix;
}
description
"The IPv6 information for a binding entry.
When the IPv6 prefix type is used,
the IPv6 source address of the CE is constructed
according to the description in RFC7596.
If the IPv6 address type is used, the CE can use
any valid /128 address from a prefix assigned to
the CE.";
reference
"Section 5.1 of RFC7596.";
}
leaf br-ipv6-addr {
type inet:ipv6-address;
mandatory true;
description
"The IPv6 address of the binding BR.";
}
}
// configuration and stateful parameters for softwire CE interface
augment "/if:interfaces/if:interface" {
when "derived-from(ift:tunnel-type, 'iana-tunnel-type:aplusp')";
description "Softwire CE interface configuration";
leaf softwire-payload-mtu {
type uint16;
units bytes;
description
"The payload IPv4 MTU for the softwire tunnel.";
}
leaf softwire-path-mru {
type uint16;
units bytes;
description
"The path MRU for the softwire (payload + encapsulation
overhead).";
}
Cui, et al. Expires April 26, 2019 [Page 22]
Internet-Draft YANG Modules for A+P Softwires October 2018
choice ce-type {
description "Sets the softwire CE mechanism";
case binding {
if-feature binding-mode;
description "CE binding configuration";
uses binding-entry;
}
case algo {
if-feature "map-e or map-t";
description "CE algorithm configuration";
container algo-instances {
description
"Indicates that the instances supports the MAP-E and/or MAP-T
function. The instances advertise the MAP-E/MAP-T
feature through the capability exchange mechanism
when a NETCONF session is established.";
list algo-instances {
key "id";
description
"MAP forwarding rule instance for
MAP-E/MAP-T";
leaf id {
type uint32;
mandatory true;
description
"Algorithm Instance ID.
This identifier can be automatically assigned
or explicitly configured.";
}
uses softwire-common:algorithm-instance;
}
}
}
}
}
augment "/if:interfaces/if:interface/if:statistics" {
when "derived-from(../ift:tunnel-type, 'iana-tunnel-type:aplusp')";
description "Softwire CE interface statistics.";
uses softwire-common:traffic-stat;
}
/*
* Notifications
Cui, et al. Expires April 26, 2019 [Page 23]
Internet-Draft YANG Modules for A+P Softwires October 2018
*/
notification softwire-ce-event {
if-feature binding-mode;
description "CE notification";
leaf ce-binding-ipv6-addr-change {
type inet:ipv6-address;
mandatory true;
description
"This notification is generated whenever the CE's binding IPv6
address changes for any reason.";
}
}
}
<CODE ENDS>
8. BR Softwire YANG Module
This module imports typedefs from [RFC6991]. It also imports the
'ietf-softwire-common' module.
<CODE BEGINS>file "ietf-softwire-br@2018-10-19.yang"
module ietf-softwire-br {
yang-version 1.1;
namespace "urn:ietf:params:xml:ns:yang:ietf-softwire-br";
prefix "softwire-br";
import ietf-inet-types {
prefix inet;
reference
"Section 4 of RFC 6991";
}
import ietf-yang-types {
prefix yang;
reference
"Section 3 of RFC 6991";
}
import ietf-softwire-common {
prefix softwire-common;
reference
"RFC XXXX: YANG Modules for IPv4-in-IPv6 Address plus Port
Softwires";
}
organization
Cui, et al. Expires April 26, 2019 [Page 24]
Internet-Draft YANG Modules for A+P Softwires October 2018
"IETF Softwire Working Group";
contact
"WG Web: <https://datatracker.ietf.org/wg/softwire/>
WG List: <mailto:softwire@ietf.org>
Author: Qi Sun
<mailto:sunqi.ietf@gmail.com>
Author: Linhui Sun
<mailto:lh.sunlinh@gmail.com>
Author: Yong Cui
<mailto:yong@csnet1.cs.tsinghua.edu.cn>
Author: Ian Farrer
<mailto:ian.farrer@telekom.de>
Author: Sladjana Zoric
<mailto:sladjana.zoric@telekom.de>
Author: Mohamed Boucadair
<mailto:mohamed.boucadair@orange.com>
Author: Rajiv
<mailto:Asati rajiva@cisco.com>";
description
"This document defines a YANG data module for the configuration and
management of A+P Softwire Border Routers. It covers Lightweight
4over6, MAP-E, and MAP-T mechanisms.
Copyright (c) 2018 IETF Trust and the persons identified as
authors of the code. All rights reserved.
Redistribution and use in source and binary forms, with or
without modification, is permitted pursuant to, and subject
to the license terms contained in, the Simplified BSD License
set forth in Section 4.c of the IETF Trust's Legal Provisions
Relating to IETF Documents
(http://trustee.ietf.org/license-info).
This version of this YANG module is part of RFC XXXX; see
the RFC itself for full legal notices.";
revision 2018-10-19 {
description
"Initial revision.";
reference
Cui, et al. Expires April 26, 2019 [Page 25]
Internet-Draft YANG Modules for A+P Softwires October 2018
"RFC XXXX: YANG Modules for IPv4-in-IPv6 Address plus Port
Softwires";
}
/*
* Groupings
*/
grouping port-set {
description
"Describes a set of layer 4 port numbers.
This may be a simple port range, or use the Port Set
Identifier (PSID) algorithm to represent a range of transport
layer ports which will be used by a NAPT.";
leaf psid-offset {
type uint8 {
range 0..16;
}
description
"The number of offset bits. In Lightweight 4over6,
the default value is 0 for assigning one contiguous
port range. In MAP-E/T, the default value is 6,
which means the system ports (0-1023) are excluded by
default and the assigned port ranges are distributed across the
entire port space, depending on either psid-len or the
number of contiguous ports.";
}
leaf psid-len {
type uint8 {
range 0..15;
}
mandatory true;
description
"The length of PSID, representing the sharing
ratio for an IPv4 address. This, along with ea-len, can
be used to calculate the number of contiguous ports per
port range";
}
leaf psid {
type uint16;
mandatory true;
description
"Port Set Identifier (PSID) value, which
identifies a set of ports algorithmically.";
Cui, et al. Expires April 26, 2019 [Page 26]
Internet-Draft YANG Modules for A+P Softwires October 2018
}
}
grouping binding-entry {
description
"The binding BR maintains an address binding table that
contains the binding between the CE's IPv6 address,
the allocated IPv4 address and restricted port-set.";
leaf binding-ipv6info {
type union {
type inet:ipv6-address;
type inet:ipv6-prefix;
}
description
"The IPv6 information for a CE binding entry.
When the IPv6 prefix type is used,
the IPv6 source address of the CE is constructed
according to the description in RFC7596;
if the IPv6 address type is used, the CE can use
any valid /128 address from a prefix assigned to
the CE.";
reference
"RFC7596: Lightweight 4over6: An Extension to the Dual-Stack
Lite Architecture";
}
leaf binding-ipv4-addr {
type inet:ipv4-address;
description
"The IPv4 address assigned to the binding CE,
which is used as the IPv4 external address
for binding CE local NAPT44.";
}
container port-set {
description
"For Lightweight 4over6, the default value
for offset should be 0, to configure one contiguous
port range.";
uses port-set {
refine "psid-offset" {
default "0";
}
}
}
leaf br-ipv6-addr {
type inet:ipv6-address;
description
"The IPv6 address for binding BR.";
}
Cui, et al. Expires April 26, 2019 [Page 27]
Internet-Draft YANG Modules for A+P Softwires October 2018
}
/*
* Features
*/
feature binding-mode {
description
"Binding is used for configuring the Lightweight 4over6 mechanism.
Binding based softwire mechanisms are IPv4-over-IPv6 tunnelling
transition mechanisms specifically intended for complete
independence between the IPv6 subnet prefix (and IPv6 address) and
IPv4 address, with or without IPv4 address sharing.
This is accomplished by maintaining state for each softwire
(per-subscriber state) in the central Border Relay (BR) and using
a hub-and-spoke forwarding architecture. In order to delegate the
NAPT function and achieve IPv4 address sharing, port-restricted
IPv4 addresses needs to be allocated to CEs.
This feature indicates that the instance functions as a binding
based softwire instance.";
reference
"RFC7596: Lightweight 4over6: An Extension to the Dual-Stack Lite
Architecture
RFC7597: Mapping of Address and Port with Encapsulation (MAP-E)
RFC7599: Mapping of Address and Port using Translation (MAP-T)";
}
feature map-e {
description
"MAP-E is an IPv6 transition mechanism for transporting IPv4
packets across an IPv6 network using IP encapsulation. MAP-E
allows for a reduction of the amount of centralized state using
rules to express IPv4/IPv6 address mappings. This introduces an
algorithmic relationship between the IPv6 subnet and IPv4 address.
This feature indicates that the instance functions as a MAP-E.";
reference
"RFC7597: Mapping of Address and Port with Encapsulation (MAP-E)";
}
feature map-t {
description
"MAP-T is an IPv6 transition mechanism for transporting IPv4
Cui, et al. Expires April 26, 2019 [Page 28]
Internet-Draft YANG Modules for A+P Softwires October 2018
packets across an IPv6 network using IP translation. It leverages
a double stateless NAT64 based solution as well as the stateless
algorithmic address & transport layer port mapping algorithm
defined for MAP-E.
This feature indicates that the instance functions as a MAP-T instance.";
reference
"RFC7599: Mapping of Address and Port using Translation (MAP-T)";
}
container br-instances {
description
"BR Instances";
choice br-type {
description
"Select binding or algorithmic BR functionality.";
case binding {
if-feature binding-mode;
container binding {
description
"binding mechanism (binding table) configuration.";
list bind-instances {
key "id";
description
"A set of binding BRs to be configured.";
leaf id {
type uint32;
mandatory true;
description
"A binding instance identifier.
This identifier can be automatically assigned
or explicitly configured.";
}
container binding-table-versioning {
description "binding table's version";
leaf version{
type uint64;
description "Incremental version number of the binding
table";
}
leaf date {
type yang:date-and-time;
description
"Timestamp of the binding table";
reference
Cui, et al. Expires April 26, 2019 [Page 29]
Internet-Draft YANG Modules for A+P Softwires October 2018
"RFC7422: Deterministic Address Mapping to Reduce Logging in
Carrier-Grade NAT Deployments";
}
}
leaf name {
type string;
description
"The name for the binding BR. It is used to uniquely
distinguish a binding instance by its name.";
}
leaf softwire-num-max {
type uint32;
mandatory true;
description
"The maximum number of softwires that can be created on
the binding BR.";
}
leaf softwire-payload-mtu {
type uint16;
units bytes;
mandatory true;
description
"The payload IPv4 MTU for binding softwire.";
}
leaf softwire-path-mru {
type uint16;
units bytes;
mandatory true;
description
"The path MRU for binding softwire.";
}
leaf enable-hairpinning {
type boolean;
default true;
description
"Enables/disables support for locally forwarding
(hairpinning) traffic between two CEs.";
reference
"RFC7596 Section 6.2";
}
container binding-table {
description "binding table";
list binding-entry {
key "binding-ipv6info";
description "binding entry";
uses binding-entry;
}
}
Cui, et al. Expires April 26, 2019 [Page 30]
Internet-Draft YANG Modules for A+P Softwires October 2018
container icmp-policy {
description
"The binding BR can be configured to process or drop
incoming ICMP messages, and to generate outgoing ICMP
error messages.";
container icmpv4-errors {
description
"ICMPv4 error processing configuration";
leaf allow-incoming-icmpv4 {
type boolean;
default true;
description
"Enables the processing of incoming ICMPv4
packets.";
reference
"RFC7596: Lightweight 4over6: An Extension to the
Dual-Stack Lite Architecture";
}
leaf icmpv4-rate {
type uint32;
description
"Rate limit threshold in messages per-second
for processing incoming ICMPv4 errors messages";
}
leaf generate-icmpv4-errors {
type boolean;
default true;
description
"Enables the generation of outgoing ICMPv4 error
messages on receipt of an inbound IPv4 packet with
no matching binding table entry.";
reference
"Seciton 5.2 of RFC7596.";
}
}
container icmpv6-errors {
description
"ICMPv6 error processing configuration";
leaf generate-icmpv6-errors {
type boolean;
default true;
description
"Enables the generation of ICMPv6 error messages if
no matching binding table entry is found for a
received packet.";
reference
Cui, et al. Expires April 26, 2019 [Page 31]
Internet-Draft YANG Modules for A+P Softwires October 2018
"Section 6.2 of RFC7596.";
}
leaf icmpv6-rate {
type uint32;
description
"Rate limit threshold in messages per-second
for sending ICMPv6 errors messages";
reference
"Section 9 of RFC7596.";
}
}
}
container traffic-stat {
config false;
description
"Traffic statistics information for the BR.";
leaf discontinuity-time {
type yang:date-and-time;
mandatory true;
description
"The time of the most recent occasion on which the BR
instance suffered a discontinuity. This must be
initialized when the BR instance is configured
or rebooted.";
}
uses softwire-common:traffic-stat;
leaf dropped-icmpv4-packets {
type yang:zero-based-counter64;
description
"ICMPv4 packets that are dropped as a result
of the ICMP policy. Typically, this can be any
incoming ICMPv4 packets if ICMPv4 processing is
disabled or incoming ICMPv4 packets that exceed
the ICMPv4 rate-limit threshold.
Discontinuities in the value of this counter can
occur at re-initialization of the management
system, and at other times as indicated by
the value of 'discontinuity-time'.";
}
leaf dropped-icmpv4-bytes {
type yang:zero-based-counter64;
description
"ICMPv4 messages, in bytes, that are dropped as
Cui, et al. Expires April 26, 2019 [Page 32]
Internet-Draft YANG Modules for A+P Softwires October 2018
a result of the ICMP policy. Typically, it
can be any incoming ICMPv4 packets if ICMPv4
processing is disabled or incoming ICMPv4
packets that exceed the ICMPv4 rate-limit
threshold.
Discontinuities in the value of this counter can
occur at re-initialization of the management
system, and at other times as indicated by
the value of 'discontinuity-time'.";
}
leaf hairpin-ipv4-packets {
type yang:zero-based-counter64;
description
"IPv4 packets locally routed between two CEs
(hairpinned).
Discontinuities in the value of this counter can
occur at re-initialization of the management
system, and at other times as indicated by
the value of 'discontinuity-time'.";
}
leaf hairpin-ipv4-bytes {
type yang:zero-based-counter64;
description
"IPv4 bytes locally routed between two CEs
(hairpinned).
Discontinuities in the value of this counter can
occur at re-initialization of the management
system, and at other times as indicated by
the value of 'discontinuity-time'.";
}
leaf active-softwire-num {
type uint32;
config false;
description
"The number of currently active softwires on the
binding instance.
Discontinuities in the value of this counter can
occur at re-initialization of the management
system, and at other times as indicated by
the value of 'discontinuity-time'.";
}
}
}
}
Cui, et al. Expires April 26, 2019 [Page 33]
Internet-Draft YANG Modules for A+P Softwires October 2018
}
case algo {
if-feature "map-e or map-t";
container algorithm {
description
" A set of parameters used for MAP-E/MAP-T.";
list algo-instances {
key "id";
description "Instances of algorithm";
leaf id {
type uint32;
mandatory true;
description
"Identifier of the algorithm instance.
This identifier can be automatically assigned
or explicitly configured. ";
}
uses softwire-common:algorithm-instance;
container port-set {
description "Indicates a set of ports.";
uses port-set;
}
container traffic-stat {
config false;
description
"Traffic statistics information for the BR.";
leaf discontinuity-time {
type yang:date-and-time;
mandatory true;
description
"The time of the most recent occasion on which the BR
instance suffered a discontinuity. This must be reset
to the current date-and-time when the BR instance
is configured or rebooted.";
}
uses softwire-common:traffic-stat;
}
}
}
}
}
}
/*
* Notifications
*/
notification softwire-binding-instance-event {
Cui, et al. Expires April 26, 2019 [Page 34]
Internet-Draft YANG Modules for A+P Softwires October 2018
if-feature binding-mode;
description
"Notifications for binding instance when an entry is
added, modified, or is not valid anymore.";
leaf bind-id {
type leafref {
path
"/br-instances/binding/"
+ "bind-instances/id";
}
description "The ID of the binding-instance that
generated the notification.";
}
leaf-list invalid-entry {
type leafref {
path
"/br-instances/binding/"
+ "bind-instances[id=current()/../bind-id]/"
+ "binding-table/binding-entry/binding-ipv6info";
}
description
"Notify the client that a specific binding entry has
expired or is invalid. The binding-ipv6info identifies an entry.";
}
leaf-list added-entry {
type inet:ipv6-address;
description
"Notify the client that a binding entry has been added.
The ipv6 address of that entry is the index. The client
gets other information from the binding BR about the entry
indexed by that ipv6 address.";
}
leaf-list modified-entry {
type leafref {
path
"/br-instances/binding/"
+ "bind-instances[id=current()/../bind-id]/"
+ "binding-table/binding-entry/binding-ipv6info";
}
description "The ID of the the binding-table entry that
has been modified.";
}
}
notification softwire-algorithm-instance-event {
if-feature "map-e or map-t";
description
"Notifications for algorithm instance when an entry is
Cui, et al. Expires April 26, 2019 [Page 35]
Internet-Draft YANG Modules for A+P Softwires October 2018
added, modified, or is not valid anymore.";
leaf algo-id {
type leafref {
path
"/br-instances/algorithm/algo-instances/id";
}
mandatory true;
description "algorithmic instance event.";
}
leaf-list invalid-entry-id {
type leafref {
path
"/br-instances/algorithm/algo-instances/id";
}
description "Invalid entry event.";
}
leaf-list added-entry {
type leafref {
path
"/br-instances/algorithm/algo-instances/id";
}
description "Added entry.";
}
leaf-list modified-entry {
type leafref {
path
"/br-instances/algorithm/algo-instances/id";
}
description "Modified entry.";
}
}
}
<CODE ENDS>
9. Common Softwire Element Groups YANG Module
This module imports typedefs from [RFC6991].
The following YANG module contains definitions that are used by both
the softwire CE and softwire BR YANG modules.
<CODE BEGINS>file "ietf-softwire-common@2018-10-19.yang"
module ietf-softwire-common {
yang-version 1.1;
namespace "urn:ietf:params:xml:ns:yang:ietf-softwire-common";
prefix "softwire-common";
Cui, et al. Expires April 26, 2019 [Page 36]
Internet-Draft YANG Modules for A+P Softwires October 2018
import ietf-inet-types {
prefix inet;
reference
"Section 4 of RFC 6991";
}
import ietf-yang-types {
prefix yang;
reference
"Section 3 of RFC 6991";
}
organization
"IETF Softwire Working Group";
contact
"WG Web: <https://datatracker.ietf.org/wg/softwire/>
WG List: <mailto:softwire@ietf.org>
Author: Qi Sun
<mailto:sunqi.ietf@gmail.com>
Author: Linhui Sun
<mailto:lh.sunlinh@gmail.com>
Author: Yong Cui
<mailto:yong@csnet1.cs.tsinghua.edu.cn>
Author: Ian Farrer
<mailto:ian.farrer@telekom.de>
Author: Sladjana Zoric
<mailto:sladjana.zoric@telekom.de>
Author: Mohamed Boucadair
<mailto:mohamed.boucadair@orange.com>
Author: Rajiv
<mailto:Asati rajiva@cisco.com>";
description
"This document defines a YANG data module defining types
common to all A+P modules.
Copyright (c) 2018 IETF Trust and the persons identified as
authors of the code. All rights reserved.
Redistribution and use in source and binary forms, with or
without modification, is permitted pursuant to, and subject
Cui, et al. Expires April 26, 2019 [Page 37]
Internet-Draft YANG Modules for A+P Softwires October 2018
to the license terms contained in, the Simplified BSD License
set forth in Section 4.c of the IETF Trust's Legal Provisions
Relating to IETF Documents
(http://trustee.ietf.org/license-info).
This version of this YANG module is part of RFC XXXX; see
the RFC itself for full legal notices.";
revision 2018-10-19 {
description
"Initial revision.";
reference
"RFC XXXX: YANG Modules for IPv4-in-IPv6 Address plus Port
Softwires";
}
feature map-e {
description
"MAP-E is an IPv6 transition mechanism for transporting IPv4
packets across an IPv6 network using IP encapsulation. MAP-E
allows for a reduction of the amount of centralized state using
rules to express IPv4/IPv6 address mappings. This introduces an
algorithmic relationship between the IPv6 subnet and IPv4 address.
This feature indicates that the instance functions as a MAP-E.";
reference
"RFC7597: Mapping of Address and Port with Encapsulation (MAP-E)";
}
feature map-t {
description
"MAP-T is an IPv6 transition mechanism for transporting IPv4
packets across an IPv6 network using IP translation. It leverages
a double stateless NAT64 based solution as well as the stateless
algorithmic address & transport layer port mapping algorithm
defined for MAP-E.
This feature indicates that the instance functions as a MAP-T instance.";
reference
"RFC7599: Mapping of Address and Port using Translation (MAP-T)";
}
/*
* Groupings
*/
Cui, et al. Expires April 26, 2019 [Page 38]
Internet-Draft YANG Modules for A+P Softwires October 2018
grouping algorithm-instance {
description
"A collection of parameters that is used fro MAP-E/MAP-T.";
leaf enable {
type boolean;
description
"Enable/disable an individual MAP-E or MAP-T rule.";
}
container algo-versioning {
description "algorithm's version";
leaf version {
type uint64;
description "Incremental version number for the algorithm";
}
leaf date {
type yang:date-and-time;
description "Timestamp when the algorithm instance was activated.";
reference
"RFC7422: Deterministic Address Mapping to Reduce Logging in
Carrier-Grade NAT Deployments";
}
}
leaf name {
type string;
description "The name for the instance.";
}
choice data-plane {
description "Selects MAP-E (encapsulation) or MAP-T
(translation)";
case encapsulation {
if-feature map-e;
description "encapsulation for MAP-E";
leaf br-ipv6-addr {
type inet:ipv6-address;
mandatory true;
description
"The IPv6 address of the MAP-E BR.";
}
}
case translation {
if-feature map-t;
description "translation for MAP-T";
leaf dmr-ipv6-prefix {
type inet:ipv6-prefix;
description
"The IPv6 prefix of the MAP-T BR.";
}
Cui, et al. Expires April 26, 2019 [Page 39]
Internet-Draft YANG Modules for A+P Softwires October 2018
}
}
leaf ea-len {
type uint8;
mandatory true;
description
"Embedded Address (EA) bits are the IPv4 EA-bits in the IPv6
address identifying an IPv4 prefix/address (or part thereof) or
a shared IPv4 address (or part thereof) and a port-set
identifier. The length of the EA-bits is defined as part of
a MAP rule for a MAP domain.";
}
leaf rule-ipv6-prefix {
type inet:ipv6-prefix;
mandatory true;
description
"The Rule IPv6 prefix defined in the mapping rule.";
}
leaf rule-ipv4-prefix {
type inet:ipv4-prefix;
mandatory true;
description
"The Rule IPv4 prefix defined in the mapping rule.";
}
leaf forwarding {
type boolean;
mandatory true;
description
"This parameter specifies whether the rule may be used for
forwarding (FMR). If set, this rule is used as an FMR;
if not set, this rule is a Basic Mapping Rule (BMR) only
and must not be used for forwarding.";
}
}
grouping traffic-stat {
description "Traffic statistics";
leaf sent-ipv4-packets {
type yang:zero-based-counter64;
description "Number of decapsulated and forwarded IPv4 packets.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
'discontinuity-time'.";
}
leaf sent-ipv4-bytes {
type yang:zero-based-counter64;
Cui, et al. Expires April 26, 2019 [Page 40]
Internet-Draft YANG Modules for A+P Softwires October 2018
description "Decapsulated/translated IPv4 traffic sent, in bytes
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
'discontinuity-time'.";
}
leaf sent-ipv6-packets {
type yang:zero-based-counter64;
description "Number of encapsulated IPv6 packets sent.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
'discontinuity-time'.";
}
leaf sent-ipv6-bytes {
type yang:zero-based-counter64;
description "Encapsulated IPv6 traffic sent, in bytes
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
'discontinuity-time'.";
}
leaf rcvd-ipv4-packets {
type yang:zero-based-counter64;
description "Number of incoming IPv4 packets at the
Internet-facing interface.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
'discontinuity-time'.";
}
leaf rcvd-ipv4-bytes {
type yang:zero-based-counter64;
description "IPv4 traffic received for processing, in bytes.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
'discontinuity-time'.";
}
leaf rcvd-ipv6-packets {
type yang:zero-based-counter64;
description "Number of IPv4-in-IPv6 packets received.
Cui, et al. Expires April 26, 2019 [Page 41]
Internet-Draft YANG Modules for A+P Softwires October 2018
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
'discontinuity-time'.";
}
leaf rcvd-ipv6-bytes {
type yang:zero-based-counter64;
description "IPv4-in-IPv6 traffic received, in bytes.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
'discontinuity-time'.";
}
leaf dropped-ipv4-packets {
type yang:zero-based-counter64;
description "Number of IPv4 packets dropped at the
Internet-facing interface.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
'discontinuity-time'.";
}
leaf dropped-ipv4-bytes {
type yang:zero-based-counter64;
description "IPv4 traffic dropped at the Internet-facing
interface, in bytes.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
'discontinuity-time'.";
}
leaf dropped-ipv6-packets {
type yang:zero-based-counter64;
description "Number of IPv4-in-IPv6 packets dropped.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
'discontinuity-time'.";
}
leaf dropped-ipv6-bytes {
type yang:zero-based-counter64;
description "IPv4-in-IPv6 traffic dropped, in bytes.
Discontinuities in the value of this counter can occur
Cui, et al. Expires April 26, 2019 [Page 42]
Internet-Draft YANG Modules for A+P Softwires October 2018
at re-initialization of the management system, and at
other times as indicated by the value of
'discontinuity-time'.";
}
leaf dropped-ipv4-fragments {
type yang:zero-based-counter64;
description "Number of fragmented IPv4 packets dropped.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
'discontinuity-time'.";
}
leaf dropped-ipv4-fragment-bytes {
type yang:zero-based-counter64;
description "Fragmented IPv4 traffic dropped, in bytes.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
'discontinuity-time'.";
}
leaf ipv6-fragments-reassembled {
type yang:zero-based-counter64;
description "Number of IPv6 fragments successfully reassembled.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
'discontinuity-time'.";
}
leaf ipv6-fragments-bytes-reassembled {
type yang:zero-based-counter64;
description "IPv6 fragments successfully reassembled, in bytes.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
'discontinuity-time'.";
}
leaf out-icmpv4-error-packets {
type yang:zero-based-counter64;
description "Internally generated ICMPv4 error packets.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
'discontinuity-time'.";
Cui, et al. Expires April 26, 2019 [Page 43]
Internet-Draft YANG Modules for A+P Softwires October 2018
}
leaf out-icmpv4-error-bytes {
type yang:zero-based-counter64;
description "Internally generated ICMPv4 error messages, in bytes.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
'discontinuity-time'.";
}
leaf out-icmpv6-error-packets {
type yang:zero-based-counter64;
description "Internally generated ICMPv6 error packets.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
'discontinuity-time'.";
}
leaf out-icmpv6-error-bytes {
type yang:zero-based-counter64;
description "Internally generated ICMPv6 error messages, in bytes.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
'discontinuity-time'.";
}
}
}
<CODE ENDS>
10. Security Considerations
The YANG modules defined in this document is designed to be accessed
via network management protocols such as NETCONF [RFC6241] or
RESTCONF [RFC8040]. The lowest NETCONF layer is the secure transport
layer, and the mandatory-to-implement secure transport is Secure
Shell (SSH) [RFC6242]. The lowest RESTCONF layer is HTTPS, and the
mandatory-to-implement secure transport is TLS [RFC8446].
The NETCONF access control model [RFC8341] provides the means to
restrict access for particular NETCONF or RESTCONF users to a
preconfigured subset of all available NETCONF or RESTCONF protocol
operations and content.
All data nodes defined in the YANG modules which can be created,
modified, and deleted (i.e., config true, which is the default) are
Cui, et al. Expires April 26, 2019 [Page 44]
Internet-Draft YANG Modules for A+P Softwires October 2018
considered sensitive. Write operations (e.g., edit-config) applied
to these data nodes without proper protection can negatively affect
network operations.
11. IANA Considerations
This document requests IANA to assign a new tunnel type under
"tunnelType" sub-registry (under "ifType definitions" registry):
o aplusp: A+P Encapsulation [RFC XXXX].
This document requests IANA to register the following URIs in the
"IETF XML Registry" [RFC3688]:
URI: urn:ietf:params:xml:ns:yang:ietf-interface-tunnel
Registrant Contact: The IESG.
XML: N/A; the requested URI is an XML namespace.
URI: urn:ietf:params:xml:ns:yang:iana-tunnel-type
Registrant Contact: IANA.
XML: N/A; the requested URI is an XML namespace.
URI: urn:ietf:params:xml:ns:yang:softwire-ce
Registrant Contact: The IESG.
XML: N/A; the requested URI is an XML namespace.
URI: urn:ietf:params:xml:ns:yang:softwire-br
Registrant Contact: The IESG.
XML: N/A; the requested URI is an XML namespace.
URI: urn:ietf:params:xml:ns:yang:softwire-common
Registrant Contact: The IESG.
XML: N/A; the requested URI is an XML namespace.
This document requests that IANA registers the following YANG modules
in the "YANG Module Names" registry [RFC6020]:
Cui, et al. Expires April 26, 2019 [Page 45]
Internet-Draft YANG Modules for A+P Softwires October 2018
name: ietf-interface-tunnel
namespace: urn:ietf:params:xml:ns:yang:ietf-interface-tunnel
prefix: ietf-interface-tunnel
reference: RFC XXXX
name: iana-tunnel-type
namespace: urn:ietf:params:xml:ns:yang:iana-tunnel-type
prefix: iana-tunnel-type
reference: RFC XXXX
name: ietf-softwire-ce
namespace: urn:ietf:params:xml:ns:yang:softwire-ce
prefix: softwire-ce
reference: RFC XXXX
name: ietf-softwire-br
namespace: urn:ietf:params:xml:ns:yang:softwire-br
prefix: softwire-br
reference: RFC XXXX
name: ietf-softwire-common
namespace: urn:ietf:params:xml:ns:yang:softwire-common
prefix: softwire-common
reference: RFC XXXX
This document defines the initial version of the IANA-maintained
iana-tunnel-type YANG module. IANA is requested to add this note:
Tunnel type values must not be directly added to the iana-tunnel-
type YANG module. They must instead be respectively added to the
"tunnelType" sub-registry (under "ifType definitions" registry).
When an tunnel type is added to the "tunnelType" registry, a new
"identity" statement must be added to the iana-tunnel-type YANG
module. The name of the "identity" is the same as the corresponding
enumeration in the IANAifType-MIB. The following substatements to
the "identity" statement should be defined:
"base": Contains the value of the tunnel type in lowercase.
"description": Replicate the description from the registry.
"reference": Replicate the reference from the registry and add the
title of the document.
Unassigned or reserved values are not present in the module.
When the iana-tunnel-type YANG module is updated, a new "revision"
Cui, et al. Expires April 26, 2019 [Page 46]
Internet-Draft YANG Modules for A+P Softwires October 2018
statement must be added in front of the existing revision statements.
IANA is requested to add this note to "tunnelType" registry:
When this registry is modified, the YANG module iana-tunnel-type
must be updated as defined in [RFCXXXX].
12. Acknowledgements
The authors would like to thank Lishan Li, Bert Wijnen, Giles Heron,
Ole Troan, Andy Wingo and Leo Tietz for their contributions to this
work.
Thanks to Sheng Jiang for the review.
Special thanks to Tom Petch for the detailed review and suggestions.
13. Contributors
The following individuals contributed to this document:
Hao Wang
Tsinghua University
Beijing 100084
P.R.China
Phone: +86-10-6278-5822
Email: wangh13@mails.tsinghua.edu.cn
14. References
14.1. Normative References
[RFC3688] Mealling, M., "The IETF XML Registry", BCP 81, RFC 3688,
DOI 10.17487/RFC3688, January 2004,
<https://www.rfc-editor.org/info/rfc3688>.
[RFC6020] Bjorklund, M., Ed., "YANG - A Data Modeling Language for
the Network Configuration Protocol (NETCONF)", RFC 6020,
DOI 10.17487/RFC6020, October 2010,
<https://www.rfc-editor.org/info/rfc6020>.
[RFC6241] Enns, R., Ed., Bjorklund, M., Ed., Schoenwaelder, J., Ed.,
and A. Bierman, Ed., "Network Configuration Protocol
(NETCONF)", RFC 6241, DOI 10.17487/RFC6241, June 2011,
<https://www.rfc-editor.org/info/rfc6241>.
Cui, et al. Expires April 26, 2019 [Page 47]
Internet-Draft YANG Modules for A+P Softwires October 2018
[RFC6242] Wasserman, M., "Using the NETCONF Protocol over Secure
Shell (SSH)", RFC 6242, DOI 10.17487/RFC6242, June 2011,
<https://www.rfc-editor.org/info/rfc6242>.
[RFC6991] Schoenwaelder, J., Ed., "Common YANG Data Types",
RFC 6991, DOI 10.17487/RFC6991, July 2013,
<https://www.rfc-editor.org/info/rfc6991>.
[RFC7224] Bjorklund, M., "IANA Interface Type YANG Module",
RFC 7224, DOI 10.17487/RFC7224, May 2014,
<https://www.rfc-editor.org/info/rfc7224>.
[RFC7596] Cui, Y., Sun, Q., Boucadair, M., Tsou, T., Lee, Y., and I.
Farrer, "Lightweight 4over6: An Extension to the Dual-
Stack Lite Architecture", RFC 7596, DOI 10.17487/RFC7596,
July 2015, <https://www.rfc-editor.org/info/rfc7596>.
[RFC7597] Troan, O., Ed., Dec, W., Li, X., Bao, C., Matsushima, S.,
Murakami, T., and T. Taylor, Ed., "Mapping of Address and
Port with Encapsulation (MAP-E)", RFC 7597,
DOI 10.17487/RFC7597, July 2015,
<https://www.rfc-editor.org/info/rfc7597>.
[RFC7598] Mrugalski, T., Troan, O., Farrer, I., Perreault, S., Dec,
W., Bao, C., Yeh, L., and X. Deng, "DHCPv6 Options for
Configuration of Softwire Address and Port-Mapped
Clients", RFC 7598, DOI 10.17487/RFC7598, July 2015,
<https://www.rfc-editor.org/info/rfc7598>.
[RFC7599] Li, X., Bao, C., Dec, W., Ed., Troan, O., Matsushima, S.,
and T. Murakami, "Mapping of Address and Port using
Translation (MAP-T)", RFC 7599, DOI 10.17487/RFC7599, July
2015, <https://www.rfc-editor.org/info/rfc7599>.
[RFC7950] Bjorklund, M., Ed., "The YANG 1.1 Data Modeling Language",
RFC 7950, DOI 10.17487/RFC7950, August 2016,
<https://www.rfc-editor.org/info/rfc7950>.
[RFC8040] Bierman, A., Bjorklund, M., and K. Watsen, "RESTCONF
Protocol", RFC 8040, DOI 10.17487/RFC8040, January 2017,
<https://www.rfc-editor.org/info/rfc8040>.
[RFC8341] Bierman, A. and M. Bjorklund, "Network Configuration
Access Control Model", STD 91, RFC 8341,
DOI 10.17487/RFC8341, March 2018,
<https://www.rfc-editor.org/info/rfc8341>.
Cui, et al. Expires April 26, 2019 [Page 48]
Internet-Draft YANG Modules for A+P Softwires October 2018
[RFC8343] Bjorklund, M., "A YANG Data Model for Interface
Management", RFC 8343, DOI 10.17487/RFC8343, March 2018,
<https://www.rfc-editor.org/info/rfc8343>.
[RFC8446] Rescorla, E., "The Transport Layer Security (TLS) Protocol
Version 1.3", RFC 8446, DOI 10.17487/RFC8446, August 2018,
<https://www.rfc-editor.org/info/rfc8446>.
14.2. Informative References
[I-D.ietf-opsawg-nat-yang]
Boucadair, M., Sivakumar, S., Jacquenet, C., Vinapamula,
S., and Q. Wu, "A YANG Module for Network Address
Translation (NAT) and Network Prefix Translation (NPT)",
draft-ietf-opsawg-nat-yang-17 (work in progress),
September 2018.
[I-D.ietf-softwire-dslite-yang]
Boucadair, M., Jacquenet, C., and S. Sivakumar, "A YANG
Data Model for Dual-Stack Lite (DS-Lite)", draft-ietf-
softwire-dslite-yang-17 (work in progress), May 2018.
[RFC6333] Durand, A., Droms, R., Woodyatt, J., and Y. Lee, "Dual-
Stack Lite Broadband Deployments Following IPv4
Exhaustion", RFC 6333, DOI 10.17487/RFC6333, August 2011,
<https://www.rfc-editor.org/info/rfc6333>.
[RFC7422] Donley, C., Grundemann, C., Sarawat, V., Sundaresan, K.,
and O. Vautrin, "Deterministic Address Mapping to Reduce
Logging in Carrier-Grade NAT Deployments", RFC 7422,
DOI 10.17487/RFC7422, December 2014,
<https://www.rfc-editor.org/info/rfc7422>.
[RFC8340] Bjorklund, M. and L. Berger, Ed., "YANG Tree Diagrams",
BCP 215, RFC 8340, DOI 10.17487/RFC8340, March 2018,
<https://www.rfc-editor.org/info/rfc8340>.
[RFC8342] Bjorklund, M., Schoenwaelder, J., Shafer, P., Watsen, K.,
and R. Wilton, "Network Management Datastore Architecture
(NMDA)", RFC 8342, DOI 10.17487/RFC8342, March 2018,
<https://www.rfc-editor.org/info/rfc8342>.
[RFC8344] Bjorklund, M., "A YANG Data Model for IP Management",
RFC 8344, DOI 10.17487/RFC8344, March 2018,
<https://www.rfc-editor.org/info/rfc8344>.
Cui, et al. Expires April 26, 2019 [Page 49]
Internet-Draft YANG Modules for A+P Softwires October 2018
[RFC8349] Lhotka, L., Lindem, A., and Y. Qu, "A YANG Data Model for
Routing Management (NMDA Version)", RFC 8349,
DOI 10.17487/RFC8349, March 2018,
<https://www.rfc-editor.org/info/rfc8349>.
Appendix A. Configutation Examples
The following sections provide examples of how the softwire YANG
modules can be used for configuring softwire elements.
A.1. Configuration Example for a lw4o6 BR Binding-Table
The lwAFTR maintains an address binding table which contains the
following 3-tuples:
o IPv6 Address for a single lwB4
o Public IPv4 Address
o Restricted port-set
The entry has two functions: the IPv6 encapsulation of inbound IPv4
packets destined to the lwB4 and the validation of outbound IPv4-in-
IPv6 packets received from the lwB4 for de-capsulation.
Consider an example for the following lw4o6 binding table entry:
lwB4 Binding IPv6 Address: 2001:db8::1
lwB4 Binding IPv4 Address: 192.0.2.1
lwB4 PSID: 0x34
lwB4 PSID Length 8
BR IPv6 Address: 2001:db8:1::2
Cui, et al. Expires April 26, 2019 [Page 50]
Internet-Draft YANG Modules for A+P Softwires October 2018
<br-instances>
<binding>
<bind-instances>
<id>1</id>
<binding-table>
<binding-entry>
<binding-ipv6info>2001:db8::1</binding-ipv6info>
<binding-ipv4-addr>192.0.2.1</binding-ipv4-addr>
<port-set>
<psid>52</psid>
<psid-len>8</psid-len>
</port-set>
<br-ipv6-addr>2001:db8:1::2</br-ipv6-addr>
</binding-entry>
</binding-table>
<softwire-num-max>1024</softwire-num-max>
<softwire-path-mru>1540</softwire-path-mru>
<softwire-payload-mtu>1500</softwire-payload-mtu>
</bind-instances>
</binding>
</br-instances>
Figure 3: lw4o6 Binding-Table Configuration XML
A.2. Configuration Example for a MAP-E BR
A MAP-E BR is configured with forward mapping rules for the CEs it is
serving. In this example (taken from [RFC7597], Appendix A, Example
2), the following parameters are required:
o Rule IPv6 Prefix
o Rule IPv4 Prefix
o Rule EA-bit bit length
o IPv6 Address of MAP-BR
The mapping rule has two functions: identifying the destination CE
IPv6 address for encapsulating inbound IPv4 packets and the
validation of outbound IPv4-in-IPv6 packets received from the CE for
de-capsulation.
The transport type for the data plane also needs to be configured for
encapsulation to enable MAP-E and forwarding needs to be enabled.
Consider an example for the following MAP-E Forwarding Mapping Rule:
Cui, et al. Expires April 26, 2019 [Page 51]
Internet-Draft YANG Modules for A+P Softwires October 2018
Data plane: encapsulation
Rule IPv6 Prefix: 2001:db8::/40
Rule IPv4 Prefix: 192.0.2.0/24
Rule EA-bit Length: 16
BR IPv6 Address: 2001:db8:ffff::1
Figure 4 provides the example MAP-E BR configuration xml.
<br-instances>
<algorithm>
<algo-instances>
<id>1234</id>
<encapsulation>
<br-ipv6-addr>2001:db8:ffff::1</br-ipv6-addr>
</encapsulation>
<ea-len>16</ea-len>
<rule-ipv4-prefix>192.0.2.0/24</rule-ipv4-prefix>
<rule-ipv6-prefix>2001:db8::/40</rule-ipv6-prefix>
<forwarding>true</forwarding>
<port-set>
<psid-offset>6</psid-offset>
<psid-len>8</psid-len>
</port-set>
</algo-instances>
</algorithm>
</br-instances>
Figure 4: MAP-E FMR Configuration XML
A.3. lw4o6 CE Configuration Example
This section provides XML examples for configuring a lw4o6 CE.
Examples for routing and NAT44 are also provided for convienience.
Consider an example for the following lw4o6 CE configuration:
lwB4 Binding IPv6 Address: 2001:db8::1
lwB4 Binding IPv4 Address: 192.0.2.1
lwB4 PSID: 0x34
lwB4 PSID Length 8
Cui, et al. Expires April 26, 2019 [Page 52]
Internet-Draft YANG Modules for A+P Softwires October 2018
BR IPv6 Address: 2001:db8:1::2
<config xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
<interfaces xmlns="urn:ietf:params:xml:ns:yang:ietf-interfaces">
<interface>
<name>lw4o6-wan</name>
<tunnel-type
xmlns:iana="urn:ietf:params:xml:ns:yang:iana-tunnel-type">
iana-tunnel-type:aplusp
</tunnel-type>
<br-ipv6-addr
xmlns="urn:ietf:params:xml:ns:yang:ietf-softwire-ce">
2001:db8:1::2
</br-ipv6-addr>
<binding-ipv6info
xmlns="urn:ietf:params:xml:ns:yang:ietf-softwire-ce">
2001:db8::1
</binding-ipv6info>
</interface>
</interfaces>
</config>
Figure 5: lw4o6 CE Configuration XML
In the example depicted in Figure 5, the interface name is defined
for the softwire tunnel. This name is then referenced by the routing
configuration for the IPv4 route. Figure 6 provides an example
configuration for the CE's IPv4 routing, using the YANG module
described in [RFC8349].
Cui, et al. Expires April 26, 2019 [Page 53]
Internet-Draft YANG Modules for A+P Softwires October 2018
<config xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
<routing xmlns="urn:ietf:params:xml:ns:yang:ietf-routing">
<control-plane-protocols>
<control-plane-protocol>
<type>static</type>
<name>v4</name>
<static-routes>
<ipv4
xmlns="urn:ietf:params:xml:ns:yang:ietf-ipv4-unicast-routing">
<route>
<destination-prefix>0.0.0.0/0</destination-prefix>
<next-hop>
<outgoing-interface>lw4o6-wan</outgoing-interface>
</next-hop>
</route>
</ipv4>
</static-routes>
</control-plane-protocol>
</control-plane-protocols>
</routing>
</config>
Figure 6: lw4o6 CE Routing Configuration XML
Figure 7 provides an example configuration for the CE's NAPT44
function, using the YANG module described in
[I-D.ietf-opsawg-nat-yang].
<config xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
<nat xmlns="urn:ietf:params:xml:ns:yang:ietf-nat">
<instances>
<instance>
<id>1</id>
<policy>
<policy-id>1</policy-id>
<external-ip-address-pool>
<pool-id>1</pool-id>
<external-ip-pool>192.0.2.1</external-ip-pool>
</external-ip-address-pool>
<port-set-restrict>
<port-set-algo>
<psid-offset>6</psid-offset>
<psid-len>8</psid-len>
<psid>52</psid>
</port-set-algo>
</port-set-restrict>
<notify-pool-usage>
<pool-id>1</pool-id>
Cui, et al. Expires April 26, 2019 [Page 54]
Internet-Draft YANG Modules for A+P Softwires October 2018
<high-threshold>80</high-threshold>
</notify-pool-usage>
</policy>
<mapping-limits>
<limit-per-protocol>
<protocol-id>1</protocol-id>
<limit>8</limit>
</limit-per-protocol>
<limit-per-protocol>
<protocol-id>6</protocol-id>
<limit>32</limit>
</limit-per-protocol>
<limit-per-protocol>
<protocol-id>17</protocol-id>
<limit>16</limit>
</limit-per-protocol>
</mapping-limits>
<mapping-table>
<mapping-entry>
<index>1</index>
<external-src-address>192.0.2.1/32</external-src-address>
<internal-src-address>192.168.1.0/24</internal-src-address>
<transport-protocol>6</transport-protocol>
</mapping-entry>
<mapping-entry>
<index>2</index>
<external-src-address>192.0.2.1/32</external-src-address>
<internal-src-address>192.168.1.0/24</internal-src-address>
<transport-protocol>17</transport-protocol>
</mapping-entry>
<mapping-entry>
<index>3</index>
<external-src-address>192.0.2.1/32</external-src-address>
<internal-src-address>192.168.1.0/24</internal-src-address>
<transport-protocol>1</transport-protocol>
</mapping-entry>
</mapping-table>
</instance>
</instances>
</nat>
</config>
Figure 7: lw4o6 NAT Configuration XML
Cui, et al. Expires April 26, 2019 [Page 55]
Internet-Draft YANG Modules for A+P Softwires October 2018
Authors' Addresses
Yong Cui
Tsinghua University
Beijing 100084
P.R. China
Phone: +86-10-6260-3059
Email: yong@csnet1.cs.tsinghua.edu.cn
Ian Farrer
Deutsche Telekom AG
CTO-ATI,Landgrabenweg 151
Bonn, NRW 53227
Germany
Email: ian.farrer@telekom.de
Mohamed Boucadair
Orange
Rennes 35000
France
Email: mohamed.boucadair@orange.com
Qi Sun
Tsinghua University
Beijing 100084
P.R. China
Phone: +86-10-6278-5822
Email: sunqi.ietf@gmail.com
Linhui Sun
Tsinghua University
Beijing 100084
P.R. China
Phone: +86-10-6278-5822
Email: lh.sunlinh@gmail.com
Cui, et al. Expires April 26, 2019 [Page 56]
Internet-Draft YANG Modules for A+P Softwires October 2018
Sladjana Zechlin
Deutsche Telekom AG
Landgrabenweg 151
Bonn, NRW 53227
Germany
Email: sladjana.zechlin@telekom.de
Rajiv Asati
Cisco Systems, Inc.
7025 Kit Creek Rd.
RTP, NC 27709
USA
Email: Rajiva@cisco.com
Cui, et al. Expires April 26, 2019 [Page 57]