TEAS Working Group T. Saad, Ed.
Internet-Draft R. Gandhi
Intended status: Standards Track Cisco Systems Inc
Expires: April 19, 2016 X. Liu
Ericsson
V. Beeram
Juniper Networks
H. Shah
Ciena
X. Chen
Huawei Technologies
R. Jones
Brocade
B. Wen
Comcast
October 17, 2015
A YANG Data Model for Traffic Engineering Tunnels and Interfaces
draft-ietf-teas-yang-te-01
Abstract
This document defines a YANG data model for the configuration and
management of Traffic Engineering (TE) interfaces and tunnels. The
model defines generic data that is reusable across multiple data and
control plane protocols.
The data model covers the configuration, operational state, remote
procedural calls, and event notifications data for TE data.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on April 19, 2016.
Saad, et al. Expires April 19, 2016 [Page 1]
Internet-Draft TE YANG Data Model October 2015
Copyright Notice
Copyright (c) 2015 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1. Terminology . . . . . . . . . . . . . . . . . . . . . . . 3
1.2. Tree Diagram . . . . . . . . . . . . . . . . . . . . . . 3
1.3. Prefixes in Data Node Names . . . . . . . . . . . . . . . 4
1.4. Open Issues and Next Steps . . . . . . . . . . . . . . . 5
1.4.1. State Data Organization . . . . . . . . . . . . . . . 5
2. Data Model Overview . . . . . . . . . . . . . . . . . . . . . 5
2.1. Design Objectives . . . . . . . . . . . . . . . . . . . . 6
2.2. Optional Features . . . . . . . . . . . . . . . . . . . . 8
2.3. Configuration Inheritance . . . . . . . . . . . . . . . . 8
2.4. Vendor Configuration Models . . . . . . . . . . . . . . . 9
3. TE Generic Model Organization . . . . . . . . . . . . . . . . 9
3.1. Global Configuration and State Data . . . . . . . . . . . 10
3.2. Interfaces Configuration and State Data . . . . . . . . . 14
3.3. Tunnels Configuration and State Data . . . . . . . . . . 18
3.4. TE LSPs State Data . . . . . . . . . . . . . . . . . . . 28
3.5. Global RPC Data . . . . . . . . . . . . . . . . . . . . . 29
3.6. Interface RPC Data . . . . . . . . . . . . . . . . . . . 29
3.7. Tunnel RPC Data . . . . . . . . . . . . . . . . . . . . . 30
3.8. Global Notifications Data . . . . . . . . . . . . . . . . 30
3.9. Interfaces Notifications Data . . . . . . . . . . . . . . 30
3.10. Tunnel Notification Data . . . . . . . . . . . . . . . . 30
4. TE Generic and Helper YANG Modules . . . . . . . . . . . . . 31
5. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 79
6. Security Considerations . . . . . . . . . . . . . . . . . . . 80
7. Acknowledgement . . . . . . . . . . . . . . . . . . . . . . . 80
8. References . . . . . . . . . . . . . . . . . . . . . . . . . 80
8.1. Normative References . . . . . . . . . . . . . . . . . . 80
8.2. Informative References . . . . . . . . . . . . . . . . . 81
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 82
Saad, et al. Expires April 19, 2016 [Page 2]
Internet-Draft TE YANG Data Model October 2015
1. Introduction
YANG [RFC6020] is a data definition language that was introduced to
define the contents of a conceptual data store that allows networked
devices to be managed using NETCONF [RFC6241]. YANG is proving
relevant beyond its initial confines, as bindings to other interfaces
(e.g. ReST) and encoding other than XML (e.g. JSON) are being
defined. Furthermore, YANG data models can be used as the basis of
implementation for other interface, such as CLI and programmatic
APIs.
This document defines a YANG data model that can be used to configure
and manage TE interfaces and P2P or P2MP TE tunnels. This data model
restricts to TE generic data that is control and data plane agnostic.
It is expected that other protocol and data plane specific modules
(e.g. RSVP-TE [RFC3209]) will augment this TE model.
1.1. Terminology
In this document, the key words "MUST", "MUST NOT", "REQUIRED",
"SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY",
and "OPTIONAL" are to be interpreted as described in BCP 14, RFC 2119
[RFC2119].
1.2. Tree Diagram
A simplified graphical representation of the data model is presented
in each section of the model. The following notations are used for
the YANG model data tree representation.
Saad, et al. Expires April 19, 2016 [Page 3]
Internet-Draft TE YANG Data Model October 2015
<status> <flags> <name> <opts> <type>
<status> is one of:
+ for current
x for deprecated
o for obsolete
<flags> is one of:
rw for read-write configuration data
ro for read-only non-configuration data
-x for execution rpcs
-n for notifications
<name> is the name of the node
If the node is augmented into the tree from another module, its name
is printed as <prefix>:<name>
<opts> is one of:
? for an optional leaf or node
! for a presence container
* for a leaf-list or list
Brackets [<keys>] for a list's keys
Curly braces {<condition>} for optional feature that make node
conditional
Colon : for marking case nodes
Ellipses ("...") subtree contents not shown
Parentheses enclose choice and case nodes, and case nodes are also
marked with a colon (":").
<type> is the name of the type for leafs and leaf-lists.
1.3. Prefixes in Data Node Names
In this document, names of data nodes and other data model objects
are prefixed using the standard prefix associated with the
corresponding YANG imported modules, as shown in Table 1.
+--------+-----------------+-----------+
| Prefix | YANG module | Reference |
+--------+-----------------+-----------+
| yang | ietf-yang-types | [RFC6991] |
| inet | ietf-inet-types | [RFC6991] |
+--------+-----------------+-----------+
Table 1: Prefixes and corresponding YANG modules
Saad, et al. Expires April 19, 2016 [Page 4]
Internet-Draft TE YANG Data Model October 2015
1.4. Open Issues and Next Steps
This document describes the YANG data model for the TE generic and
helper modules. It also describes the high-level relationship
between these modules and to other external protocol modules. The
current revision of the draft focuses on configuration and state data
aspects of the model. It is expected that the future revisions will
cover RPC, and notification aspects.
Also, the models that define technology specific extensions to the
generic TE model (e.g. OTN [RFC4328] TE extensions), are expected to
be addressed in separate documents.
1.4.1. State Data Organization
Pure state data (for example, ephemeral or protocol derived state
objects) can be modeled using one of the options below:
o Contained inside the read-write container, under the "state" sub-
container, as shown in Figure 3
o Contained inside a separate read-only container, for example a
tunnels-state container
The first option allows for the reusing of the containers that hold
configuration data (in the "config" sub-container), and by placing
state data under the read-only "state" sub-container of the parent
container. However, when adopting this approach for ephemeral or
purely derived states (e.g. auto tunnels), and since in this case the
state hangs off the read-write parent container, it will be possible
to delete the parent container and subsequently the ephemeral read-
only state contained within (see Figure 3).
The second option entails defining a new read-only parent container
in the model (e.g. neighbors-state) that holds the data.
This revision of the draft adopts the first option. Further
discussions on this topic are expected to close on the best choice to
adopt.
2. Data Model Overview
Although the basis of TE elements remain similar across different
vendor implementations, however, the details of a TE model will
usually vary across different vendor implementations. Also,
implementations may vary in their support of the complete set of TE
features. The TE YANG module defined in this document is an attempts
to define a vendor agnostic model that will prescribe to IETF
Saad, et al. Expires April 19, 2016 [Page 5]
Internet-Draft TE YANG Data Model October 2015
standard terminology when different representation of data is
possible.
The model is composed of common building blocks that are independent
of specific data or control plane instantiations. It covers data
representation for the configuration, state, remote procedural calls
(RPCs), and event notifications.
Throughout the model, the approach described in
[I-D.openconfig-netmod-opstate] is adopted to represent data
pertaining to configuration intended state, applied state and derived
state data elements. Each container in the model hold a "config" and
"state" sub-container. The "config" sub-container is used to
represent the intended configurable parameters, and the state sub-
container is used to represent both the applied configurable
parameters and any derived state, such as counters or statistical
information.
The decision to use this approach was made to better align with the
MPLS consolidated model in [I-D.openconfig-mpls-consolidated-model],
and maximize reusability of groupings defined in this document and
allow for possible convergence between the two models.
2.1. Design Objectives
The goal of this document is to define a TE data model that can
represent different TE vendor implementations, while adhering to
standard terminology and behavior when resolving differences in
implementations.
The following considerations with respect data organization are taken
into account when defining the model:
o reusable data elements are grouped into separate TE types
module(s) that can be readily imported by other modules whenever
needed
o reusable TE data types that are data plane independent are grouped
in the TE generic types module "ietf-te-types.yang"
o reusable TE data elements that are data plane specific (e.g.
packet PSC or switching technologies as defined in [RFC3473]) are
expected to be grouped in a technology- specific types module,
e.g. "ietf-te-psc-types.yang". It is expected that technology
specific types will augment TE generic types as shown in Figure 1
Saad, et al. Expires April 19, 2016 [Page 6]
Internet-Draft TE YANG Data Model October 2015
+---------+
| ietf-te | ^: import
+---------+ o: augment
import ^
|
|
+---------------+
| ietf-te-types |
+---------------+
o o
| \
| \
+-------------------+ +-------------------+
| ietf-te-psc-types | | ietf-te-otn-types |
+-------------------+ +-------------------+
(shown for illustration
not in this document)
Figure 1: Relationship between generic and technology specific TE
types modules
o TE generic module includes data elements that are control plane
independent. Data elements specific to a control plane protocol
(e.g. RSVP-TE [RFC3209]) are expected to be in a separate module
that augments the TE generic module. It is also expected that
data relevant to a specific instantiations of data plane
technology will exist in a separate YANG module that augments the
TE generic model, see Figure 2.
Saad, et al. Expires April 19, 2016 [Page 7]
Internet-Draft TE YANG Data Model October 2015
TE generic +---------+ ^: import
module | ietf-te | o: augment
+---------+
| o
| |
v |
+--------------+
RSVP-TE module | ietf-rsvp-te |o . . .
+--------------+ \
^ | \
| o +-------------------+
+-----------+ | ietf-rsvp-otn-te |
RSVP module | ietf-rsvp | +-------------------+
+-----------+ RSVP-TE with OTN
extensions
(shown for illustration
not in this document)
Figure 2: Relationship of TE module with other control plane protocol
modules
o In general, little information in the model is designated as
"mandatory", to allow freedom to vendors to adapt the data model
to their specific product implementation.
2.2. Optional Features
Optional features are features beyond the generic TE model, and
hence, it is up to a vendor to decide whether or not to support of a
particular feature on a particular device.
This module declares a number of TE functions as features (such as
P2MP-TE, soft-preemption etc.). It is intended that vendors will
extend this features list.
2.3. Configuration Inheritance
The defined data model supports configuration inheritance for
tunnels, paths, and interfaces. Data elements defined in the main
container (e.g. that encompasses the list of tunnels, interfaces, or
paths) are assumed to apply equally to all elements of the list,
unless overridden explicitly for a certain element (e.g. tunnel,
interface or path). Vendors are expected to augment the above
container(s) to provide the list of inheritance command for their
implementations.
Saad, et al. Expires April 19, 2016 [Page 8]
Internet-Draft TE YANG Data Model October 2015
2.4. Vendor Configuration Models
There two main popular types of routing protocol configuration that
vendors may support:
o protocol centric - all the protocol related configuration is
contained within the protocol itself. Configuration belonging to
multiple instances of the protocol running in different routing-
instances (e.g. VRFs) are contained under the default routing
instance [I-D.ietf-netmod-routing-cfg]:
o VRF centric - all the protocol related configuration for a
routing- instance is contained within this routing-instance.
On-going discussions within the IETF community have converged on
adopting the VRF centric approach. The proposed model in this
document adheres to this conclusion.
3. TE Generic Model Organization
This model covers configuration, state, RPC, and notifications data
pertaining to TE global parameters, interfaces, and tunnels
parameters.
The container "te" is the top level container in this data model.
The presence of this container is expected to enable TE function
system wide.
The approach described in [I-D.openconfig-netmod-opstate] allows for
modeling the intended and respective applied and derived state. The
TE state data in this model falls into one of the following
categories:
o State corresponding to applied configuration
o State corresponding to derived state, counters, stats, etc.
o State corresponding to ephemeral data (e.g. LSPs, etc.)
Data for the first two categories are contained under the respective
"state" sub-container of the intended object (e.g. tunnel). The last
category falls under a separate - e.g. lsps-state- container that
contains the attributes of a purely derived state data (e.g.
ephemeral objects) that are not associated with any configuration as
shown in Figure 3.
Saad, et al. Expires April 19, 2016 [Page 9]
Internet-Draft TE YANG Data Model October 2015
module: ietf-te
+--rw te!
+--rw globals
+-- rw config
<<intended configuration>>
.
+-- ro state
<<applied configuration>>
<<derived state associated with the tunnel>>
.
.
+--rw interfaces
+-- rw config
<<intended configuration>>
.
+-- ro state
<<applied configuration>>
<<derived state associated with the tunnel>>
.
.
+--rw tunnels
+-- rw config
<<intended configuration>>
.
+-- ro state
<<applied configuration>>
<<derived state associated with the tunnel>>
.
.
rpcs:
+---x globals-rpc
+---x interfaces-rpc
+---x tunnels-rpc
notifications:
+---n globals-notif
+---n interfaces-notif
+---n tunnels-notif
Figure 3: TE highlevel model view
3.1. Global Configuration and State Data
This branch of the data model covers configurations that control TE
features behavior system-wide, and its respective state. Examples of
such configuration data are:
o Table of named SRLG mappings
Saad, et al. Expires April 19, 2016 [Page 10]
Internet-Draft TE YANG Data Model October 2015
o Table of named (extended) administrative groups mappings
o Table of named explicit paths to be referenced by TE tunnels
o Table of named path-constraints sets
o Auto-bandwidth global parameters
o TE diff-serve TE-class maps
o System-wide capabilities for LSP reoptimization
* Reoptimization timers (periodic interval, LSP installation and
cleanup)
o System-wide capabilities for TE state flooding
* Periodic flooding interval
o System-wide capabilities that affect the originating, traversing
and terminating LSPs. For example:
* Path selection parameters (e.g. metric) at head-end LSR
* Path protection parameters at head-end LSR
* (Soft) preemption parameters
* Fast reroute parameters
The approach described in [I-D.openconfig-netmod-opstate] is utilised
to include the global state data under the global "state" sub-
container as shown in Figure 3.
Examples of such states are:
o Global statistics (signaling, admission, preemption, flooding)
o Global counters (number of tunnels/LSPs/interfaces)
module: ietf-te
+--rw te!
+--rw globals
| +--rw config
| | +--rw named-admin-groups* [name]
| | | +--rw name string
| | | +--rw group? ietf-te-types:admin-groups
| | +--rw named-srlgs* [name] {ietf-te-types:named-srlg-groups}?
Saad, et al. Expires April 19, 2016 [Page 11]
Internet-Draft TE YANG Data Model October 2015
| | | +--rw name string
| | | +--rw group? ietf-te-types:srlg
| | +--rw named-explicit-paths* [name]
| | | +--rw name string
| | | +--rw explicit-route-objects* [index]
| | | +--rw index uint8
| | | +--rw (type)?
| | | | +--:(ipv4-address)
| | | | | +--rw v4-address? inet:ipv4-address
| | | | | +--rw v4-prefix-length? uint8
| | | | | +--rw v4-loose? boolean
| | | | +--:(ipv6-address)
| | | | | +--rw v6-address? inet:ipv6-address
| | | | | +--rw v6-prefix-length? uint8
| | | | | +--rw v6-loose? boolean
| | | | +--:(as-number)
| | | | | +--rw as-number? uint16
| | | | +--:(unnumbered-link)
| | | | | +--rw router-id? inet:ip-address
| | | | | +--rw interface-id? uint32
| | | | +--:(label)
| | | | +--rw value? uint32
| | | +--rw explicit-route-usage? identityref
| | +--rw named-constraints* [name]
| | | +--rw name string
| | | +--rw path-selection
| | | +--rw topology? te-types:topology-id
| | | +--rw cost-limit? uint32
| | | +--rw hop-limit? uint8
| | | +--rw metric-type? identityref
| | | +--rw tiebreaker-type? identityref
| | | +--rw ignore-overload? boolean
| | | +--rw tunnel-path-affinities {named-path-affinities}?
| | | | +--rw (style)?
| | | | +--:(values)
| | | | | +--rw value? uint32
| | | | | +--rw mask? uint32
| | | | +--:(named)
| | | | +--rw constraints* [usage]
| | | | +--rw usage identityref
| | | | +--rw constraint
| | | | +--rw affinity-names* [name]
| | | | +--rw name string
| | | +--rw tunnel-path-srlgs
| | | +--rw (style)?
| | | +--:(values)
| | | | +--rw usage? identityref
| | | | +--rw values* te-types:srlg
Saad, et al. Expires April 19, 2016 [Page 12]
Internet-Draft TE YANG Data Model October 2015
| | | +--:(named)
| | | +--rw constraints* [usage]
| | | +--rw usage identityref
| | | +--rw constraint
| | | +--rw srlg-names* [name]
| | | +--rw name string
| | +--rw lsp-install-interval? uint32
| | +--rw lsp-cleanup-interval? uint32
| +--ro state
| +--ro named-admin-groups* [name]
| | +--ro name string
| | +--ro group? ietf-te-types:admin-groups
| +--ro named-srlgs* [name] {ietf-te-types:named-srlg-groups}?
| | +--ro name string
| | +--ro group? ietf-te-types:srlg
| +--ro named-explicit-paths* [name]
| | +--ro name string
| | +--ro explicit-route-objects* [index]
| | +--ro index uint8
| | +--ro (type)?
| | | +--:(ipv4-address)
| | | | +--ro v4-address? inet:ipv4-address
| | | | +--ro v4-prefix-length? uint8
| | | | +--ro v4-loose? boolean
| | | +--:(ipv6-address)
| | | | +--ro v6-address? inet:ipv6-address
| | | | +--ro v6-prefix-length? uint8
| | | | +--ro v6-loose? boolean
| | | +--:(as-number)
| | | | +--ro as-number? uint16
| | | +--:(unnumbered-link)
| | | | +--ro router-id? inet:ip-address
| | | | +--ro interface-id? uint32
| | | +--:(label)
| | | +--ro value? uint32
| | +--ro explicit-route-usage? identityref
| +--ro named-constraints* [name]
| | +--ro name string
| | +--ro path-selection
| | +--ro topology? te-types:topology-id
| | +--ro cost-limit? uint32
| | +--ro hop-limit? uint8
| | +--ro metric-type? identityref
| | +--ro tiebreaker-type? identityref
| | +--ro ignore-overload? boolean
| | +--ro tunnel-path-affinities {named-path-affinities}?
| | | +--ro (style)?
| | | +--:(values)
Saad, et al. Expires April 19, 2016 [Page 13]
Internet-Draft TE YANG Data Model October 2015
| | | | +--ro value? uint32
| | | | +--ro mask? uint32
| | | +--:(named)
| | | +--ro constraints* [usage]
| | | +--ro usage identityref
| | | +--ro constraint
| | | +--ro affinity-names* [name]
| | | +--ro name string
| | +--ro tunnel-path-srlgs
| | +--ro (style)?
| | +--:(values)
| | | +--ro usage? identityref
| | | +--ro values* te-types:srlg
| | +--:(named)
| | +--ro constraints* [usage]
| | +--ro usage identityref
| | +--ro constraint
| | +--ro srlg-names* [name]
| | +--ro name string
| +--ro lsp-install-interval? uint32
| +--ro lsp-cleanup-interval? uint32
| +--ro tunnels-counter? uint32
| +--ro lsps-counter? uint32
Figure 4: TE globals configuration and state tree
3.2. Interfaces Configuration and State Data
This branch of the data model covers configurations elements that
control TE features behavior system-wide. Examples of such
configuration data are:
This branch of the data model covers configurations that control TE
features behavior system-wide, and its respective state. Examples of
such configuration data are:
This branch of the model covers configuration and state data items,
the corresponding applied state data, and possible derived state
pertaining to TE interfaces. Examples of tunnel configuration date
for TE interfaces are:
o Maximum reservable bandwidth, bandwidth constraints (BC)
o Flooding parameters
* Flooding intervals and threshold values
Saad, et al. Expires April 19, 2016 [Page 14]
Internet-Draft TE YANG Data Model October 2015
o Fast reroute backup tunnel properties (such as static, auto-
tunnel)
o interface attributes
* (Extended) administrative groups
* SRLG values
* TE metric value
module: ietf-te
+--rw te!
+--rw interfaces
| +--rw config
| | +--rw thresholds
| | +--rw (type)?
| | +--:(equal-steps)
| | | +--rw (equal-step-type)?
| | | +--:(up-down-different-step)
| | | | +--rw up-step? uint8
| | | | +--rw down-step? uint8
| | | +--:(up-down-same-step)
| | | +--rw step? uint8
| | +--:(unequal-steps)
| | +--rw up-steps* [value]
| | | +--rw value uint8
| | +--rw down-steps* [value]
| | +--rw value uint8
| +--ro state
| | +--ro thresholds
| | +--ro (type)?
| | +--:(equal-steps)
| | | +--ro (equal-step-type)?
| | | +--:(up-down-different-step)
| | | | +--ro up-step? uint8
| | | | +--ro down-step? uint8
| | | +--:(up-down-same-step)
| | | +--ro step? uint8
| | +--:(unequal-steps)
| | +--ro up-steps* [value]
| | | +--ro value uint8
| | +--ro down-steps* [value]
| | +--ro value uint8
| +--rw interface* [interface]
| +--rw interface if:interface-ref
| +--rw config
| | +--rw te-metric? ietf-te-types:te-metric
Saad, et al. Expires April 19, 2016 [Page 15]
Internet-Draft TE YANG Data Model October 2015
| | +--rw (admin-group-type)?
| | | +--:(value-admin-groups)
| | | | +--rw (value-admin-group-type)?
| | | | +--:(value-admin-groups)
| | | | | +--rw admin-group?
| | | | +--:(value-extended-admin-groups)
| | | | +--rw extended-admin-group
| | | +--:(named-admin-groups)
| | | +--rw named-admin-groups* [named-admin-group]
| | | +--rw named-admin-group ->
../../../../../globals/config/named-admin-groups/name
| | +--rw (srlg-type)?
| | | +--:(value-srlgs)
| | | | +--rw values* [value]
| | | | +--rw value uint32
| | | +--:(named-srlgs)
| | | +--rw named-srlgs* [named-srlg]
| | | +--rw named-srlg ->
../../../../../globals/config/named-srlgs/name
| | +--rw switching-capabilities* [switching-capability]
| | | +--rw switching-capability identityref
| | | +--rw encoding? identityref
| | +--rw thresholds
| | +--rw (type)?
| | +--:(equal-steps)
| | | +--rw (equal-step-type)?
| | | +--:(up-down-different-step)
| | | | +--rw up-step? uint8
| | | | +--rw down-step? uint8
| | | +--:(up-down-same-step)
| | | +--rw step? uint8
| | +--:(unequal-steps)
| | +--rw up-steps* [value]
| | | +--rw value uint8
| | +--rw down-steps* [value]
| | +--rw value uint8
| +--ro state
| +--ro te-metric? ietf-te-types:te-metric
| +--ro (admin-group-type)?
| | +--:(value-admin-groups)
| | | +--ro (value-admin-group-type)?
| | | +--:(value-admin-groups)
| | | | +--ro admin-group
| | | +--:(value-extended-admin-groups)
| | | +--ro extended-admin-group
| | +--:(named-admin-groups)
| | +--ro named-admin-groups* [named-admin-group]
| | +--ro named-admin-group ->
Saad, et al. Expires April 19, 2016 [Page 16]
Internet-Draft TE YANG Data Model October 2015
../../../../../globals/config/named-admin-groups/name
| +--ro (srlg-type)?
| | +--:(value-srlgs)
| | | +--ro values* [value]
| | | +--ro value uint32
| | +--:(named-srlgs)
| | +--ro named-srlgs* [named-srlg]
| | +--ro named-srlg ->
../../../../../globals/config/named-srlgs/name
| +--ro switching-capabilities* [switching-capability]
| | +--ro switching-capability identityref
| | +--ro encoding? identityref
| +--ro thresholds
| | +--ro (type)?
| | +--:(equal-steps)
| | | +--ro (equal-step-type)?
| | | +--:(up-down-different-step)
| | | | +--ro up-step? uint8
| | | | +--ro down-step? uint8
| | | +--:(up-down-same-step)
| | | +--ro step? uint8
| | +--:(unequal-steps)
| | +--ro up-steps* [value]
| | | +--ro value uint8
| | +--ro down-steps* [value]
| | +--ro value uint8
| +--ro te-advertisements_state
| +--ro flood-interval? uint32
| +--ro last-flooded-time? uint32
| +--ro next-flooded-time? uint32
| +--ro last-flooded-trigger? enumeration
| +--ro advertized-level-areas* [level-area]
| +--ro level-area uint32
Figure 5: TE interfaces configuration and state tree
The state corresponding to the TE interfaces applied configuration,
protocol derived state, and stats and counters all fall under the
interface "state" sub-container as shown in Figure 6 below:
Saad, et al. Expires April 19, 2016 [Page 17]
Internet-Draft TE YANG Data Model October 2015
module: ietf-te
+--rw te!
+--rw interfaces
.
+-- rw te-attributes
+-- rw config
<<intended configuration>>
.
+-- ro state
<<applied configuration>>
<<derived state associated with the TE interface>>
Figure 6: TE interface state
This covers state data for TE interfaces such as:
o Bandwidth information: maximum bandwidth, available bandwidth at
different priorities and for each class-type (CT)
o List of admitted LSPs
* Name, bandwidth value and pool, time, priority
o Statistics: state counters, flooding counters, admission counters
(accepted/rejected), preemption counters
o Adjacency information
* Neighbor address
* Metric value
3.3. Tunnels Configuration and State Data
This branch of the model covers intended, and corresponding applied
configuration for tunnels. As well, it holds possible derived state
pertaining to TE tunnels.
The approach described in [I-D.openconfig-netmod-opstate] is utilised
for the inclusion of operational and statistical data as shown in
Figure 7.
Saad, et al. Expires April 19, 2016 [Page 18]
Internet-Draft TE YANG Data Model October 2015
module: ietf-te
+--rw te!
+--rw tunnels
.
+-- rw config
<<intended configuration>>
.
+-- ro state
<<applied configuration>>
<<derived state associated with the tunnel>>
Figure 7: TE interface state tree
Examples of tunnel configuration date for TE tunnels:
o Name and type (e.g. P2P, P2MP) of tunnel
o Admin-state
o Primary and secondary paths
o Routing usage (auto-route announce, forwarding adjacency)
o Policy based routing (PBR) parameters
module: ietf-te
+--rw te!
+--rw tunnels
| +--rw tunnel* [name type]
| +--rw name string
| +--rw type identityref
| +--rw identifier? uint16
| +--rw config
| | +--rw description? string
| | +--rw admin-status? identityref
| | +--rw (routing-choice)?
| | | +--:(autoroute)
| | | | +--rw autoroute-announce!
| | | | +--rw routing-afs* inet:ip-version
| | | | +--rw (metric-type)?
| | | | +--:(metric)
| | | | | +--rw metric? uint32
| | | | +--:(relative-metric)
| | | | | +--rw relative-metric? int32
| | | | +--:(absolute-metric)
| | | | +--rw absolute-metric? uint32
| | | +--:(forwarding-adjacency)
| | | +--rw forwarding-adjacency!
Saad, et al. Expires April 19, 2016 [Page 19]
Internet-Draft TE YANG Data Model October 2015
| | | +--rw holdtime? uint32
| | | +--rw routing-afs* inet:ip-version
| | +--rw forwarding
| | | +--rw load-share? uint32
| | | +--rw (policy-type)?
| | | +--:(class)
| | | | +--rw class
| | | | +--rw class? uint8
| | | +--:(group)
| | | +--rw group
| | | +--rw classes* uint8
| | +--rw bidirectional
| | | +--rw association
| | | +--rw id? uint16
| | | +--rw source? inet:ip-address
| | | +--rw global-source? inet:ip-address
| | | +--rw type? identityref
| | | +--rw provisioing? identityref
| | +--rw (path-type)?
| | +--:(p2p)
| | | +--rw destination? inet:ip-address
| | | +--rw primary-paths* [preference]
| | | +--rw preference uint8
| | | +--rw path-named-constraint? string
| | | +--rw path-selection
| | | | +--rw topology? te-types:topology-id
| | | | +--rw cost-limit? uint32
| | | | +--rw hop-limit? uint8
| | | | +--rw metric-type? identityref
| | | | +--rw tiebreaker-type? identityref
| | | | +--rw ignore-overload? boolean
| | | | +--rw tunnel-path-affinities
| | | | | +--rw (style)?
| | | | | +--:(values)
| | | | | | +--rw value? uint32
| | | | | | +--rw mask? uint32
| | | | | +--:(named)
| | | | | +--rw constraints* [usage]
| | | | | +--rw usage identityref
| | | | | +--rw constraint
| | | | | +--rw affinity-names* [name]
| | | | | +--rw name string
| | | | +--rw tunnel-path-srlgs
| | | | +--rw (style)?
| | | | +--:(values)
| | | | | +--rw usage? identityref
| | | | | +--rw values* te-types:srlg
| | | | +--:(named)
Saad, et al. Expires April 19, 2016 [Page 20]
Internet-Draft TE YANG Data Model October 2015
| | | | +--rw constraints* [usage]
| | | | +--rw usage identityref
| | | | +--rw constraint
| | | | +--rw srlg-names* [name]
| | | | +--rw name string
| | | +--rw (type)?
| | | | +--:(dynamic)
| | | | | +--rw dynamic? empty
| | | | +--:(explicit)
| | | | +--rw explicit-path-name? string
| | | +--rw no-cspf? empty
| | | +--rw lockdown? empty
| | | +--rw secondary-paths* [preference]
| | | +--rw preference uint8
| | | +--rw path-named-constraint? string
| | | +--rw path-selection
| | | | +--rw topology? te-types:topology-id
| | | | +--rw cost-limit? uint32
| | | | +--rw hop-limit? uint8
| | | | +--rw metric-type? identityref
| | | | +--rw tiebreaker-type? identityref
| | | | +--rw ignore-overload? boolean
| | | | +--rw tunnel-path-affinities
| | | | | +--rw (style)?
| | | | | +--:(values)
| | | | | | +--rw value? uint32
| | | | | | +--rw mask? uint32
| | | | | +--:(named)
| | | | | +--rw constraints* [usage]
| | | | | +--rw usage identityref
| | | | | +--rw constraint
| | | | | +--rw affinity-names* [name]
| | | | | +--rw name string
| | | | +--rw tunnel-path-srlgs
| | | | +--rw (style)?
| | | | +--:(values)
| | | | | +--rw usage? identityref
| | | | | +--rw values* te-types:srlg
| | | | +--:(named)
| | | | +--rw constraints* [usage]
| | | | +--rw usage identityref
| | | | +--rw constraint
| | | | +--rw srlg-names* [name]
| | | | +--rw name string
| | | +--rw (type)?
| | | | +--:(dynamic)
| | | | | +--rw dynamic? empty
| | | | +--:(explicit)
Saad, et al. Expires April 19, 2016 [Page 21]
Internet-Draft TE YANG Data Model October 2015
| | | | +--rw explicit-path-name? string
| | | +--rw no-cspf? empty
| | | +--rw lockdown? empty
| | +--:(p2mp) {ietf-te-types:p2mp-te}?
| | +--rw p2mp-paths* [destination]
| | +--rw destination inet:ip-address
| | +--rw primary-paths* [preference]
| | +--rw preference uint8
| | +--rw path-named-constraint? string
| | +--rw path-selection
| | | +--rw topology? te-types:topology-id
| | | +--rw cost-limit? uint32
| | | +--rw hop-limit? uint8
| | | +--rw metric-type? identityref
| | | +--rw tiebreaker-type? identityref
| | | +--rw ignore-overload? boolean
| | | +--rw tunnel-path-affinities
| | | | +--rw (style)?
| | | | +--:(values)
| | | | | +--rw value? uint32
| | | | | +--rw mask? uint32
| | | | +--:(named)
| | | | +--rw constraints* [usage]
| | | | +--rw usage identityref
| | | | +--rw constraint
| | | | +--rw affinity-names* [name]
| | | | +--rw name string
| | | +--rw tunnel-path-srlgs
| | | +--rw (style)?
| | | +--:(values)
| | | | +--rw usage? identityref
| | | | +--rw values* te-types:srlg
| | | +--:(named)
| | | +--rw constraints* [usage]
| | | +--rw usage identityref
| | | +--rw constraint
| | | +--rw srlg-names* [name]
| | | +--rw name string
| | +--rw (type)?
| | | +--:(dynamic)
| | | | +--rw dynamic? empty
| | | +--:(explicit)
| | | +--rw explicit-path-name? string
| | +--rw no-cspf? empty
| | +--rw lockdown? empty
| | +--rw secondary-paths* [preference]
| | +--rw preference uint8
| | +--rw path-named-constraint? string
Saad, et al. Expires April 19, 2016 [Page 22]
Internet-Draft TE YANG Data Model October 2015
| | +--rw path-selection
| | | +--rw topology? te-types:topology-id
| | | +--rw cost-limit? uint32
| | | +--rw hop-limit? uint8
| | | +--rw metric-type? identityref
| | | +--rw tiebreaker-type? identityref
| | | +--rw ignore-overload? boolean
| | | +--rw tunnel-path-affinities
| | | | +--rw (style)?
| | | | +--:(values)
| | | | | +--rw value? uint32
| | | | | +--rw mask? uint32
| | | | +--:(named)
| | | | +--rw constraints* [usage]
| | | | +--rw usage identityref
| | | | +--rw constraint
| | | | +--rw affinity-names* [name]
| | | | +--rw name string
| | | +--rw tunnel-path-srlgs
| | | +--rw (style)?
| | | +--:(values)
| | | | +--rw usage? identityref
| | | | +--rw values* te-types:srlg
| | | +--:(named)
| | | +--rw constraints* [usage]
| | | +--rw usage identityref
| | | +--rw constraint
| | | +--rw srlg-names* [name]
| | | +--rw name string
| | +--rw (type)?
| | | +--:(dynamic)
| | | | +--rw dynamic? empty
| | | +--:(explicit)
| | | +--rw explicit-path-name? string
| | +--rw no-cspf? empty
| | +--rw lockdown? empty
| +--ro state
| +--ro description? string
| +--ro admin-status? identityref
| +--ro (routing-choice)?
| | +--:(autoroute)
| | | +--ro autoroute-announce!
| | | +--ro routing-afs* inet:ip-version
| | | +--ro (metric-type)?
| | | +--:(metric)
| | | | +--ro metric? uint32
| | | +--:(relative-metric)
| | | | +--ro relative-metric? int32
Saad, et al. Expires April 19, 2016 [Page 23]
Internet-Draft TE YANG Data Model October 2015
| | | +--:(absolute-metric)
| | | +--ro absolute-metric? uint32
| | +--:(forwarding-adjacency)
| | +--ro forwarding-adjacency!
| | +--ro holdtime? uint32
| | +--ro routing-afs* inet:ip-version
| +--ro forwarding
| | +--ro load-share? uint32
| | +--ro (policy-type)?
| | +--:(class)
| | | +--ro class
| | | +--ro class? uint8
| | +--:(group)
| | +--ro group
| | +--ro classes* uint8
| +--ro bidirectional
| | +--ro association
| | +--ro id? uint16
| | +--ro source? inet:ip-address
| | +--ro global-source? inet:ip-address
| | +--ro type? identityref
| | +--ro provisioing? identityref
| +--ro (path-type)?
| | +--:(p2p)
| | | +--ro destination? inet:ip-address
| | | +--ro primary-paths* [preference]
| | | +--ro preference uint8
| | | +--ro path-named-constraint? string
| | | +--ro path-selection
| | | | +--ro topology? te-types:topology-id
| | | | +--ro cost-limit? uint32
| | | | +--ro hop-limit? uint8
| | | | +--ro metric-type? identityref
| | | | +--ro tiebreaker-type? identityref
| | | | +--ro ignore-overload? boolean
| | | | +--ro tunnel-path-affinities
| | | | | +--ro (style)?
| | | | | +--:(values)
| | | | | | +--ro value? uint32
| | | | | | +--ro mask? uint32
| | | | | +--:(named)
| | | | | +--ro constraints* [usage]
| | | | | +--ro usage identityref
| | | | | +--ro constraint
| | | | | +--ro affinity-names* [name]
| | | | | +--ro name string
| | | | +--ro tunnel-path-srlgs
| | | | +--ro (style)?
Saad, et al. Expires April 19, 2016 [Page 24]
Internet-Draft TE YANG Data Model October 2015
| | | | +--:(values)
| | | | | +--ro usage? identityref
| | | | | +--ro values* te-types:srlg
| | | | +--:(named)
| | | | +--ro constraints* [usage]
| | | | +--ro usage identityref
| | | | +--ro constraint
| | | | +--ro srlg-names* [name]
| | | | +--ro name string
| | | +--ro (type)?
| | | | +--:(dynamic)
| | | | | +--ro dynamic? empty
| | | | +--:(explicit)
| | | | +--ro explicit-path-name? string
| | | +--ro no-cspf? empty
| | | +--ro lockdown? empty
| | | +--ro secondary-paths* [preference]
| | | +--ro preference uint8
| | | +--ro path-named-constraint? string
| | | +--ro path-selection
| | | | +--ro topology?te-types:topology-id
| | | | +--ro cost-limit? uint32
| | | | +--ro hop-limit? uint8
| | | | +--ro metric-type? identityref
| | | | +--ro tiebreaker-type? identityref
| | | | +--ro ignore-overload? boolean
| | | | +--ro tunnel-path-affinities
| | | | | +--ro (style)?
| | | | | +--:(values)
| | | | | | +--ro value? uint32
| | | | | | +--ro mask? uint32
| | | | | +--:(named)
| | | | | +--ro constraints* [usage]
| | | | | +--ro usage identityref
| | | | | +--ro constraint
| | | | | +--ro affinity-names* [name]
| | | | | +--ro name string
| | | | +--ro tunnel-path-srlgs
| | | | +--ro (style)?
| | | | +--:(values)
| | | | | +--ro usage? identityref
| | | | | +--ro values* te-types:srlg
| | | | +--:(named)
| | | | +--ro constraints* [usage]
| | | | +--ro usage identityref
| | | | +--ro constraint
| | | | +--ro srlg-names* [name]
| | | | +--ro name string
Saad, et al. Expires April 19, 2016 [Page 25]
Internet-Draft TE YANG Data Model October 2015
| | | +--ro (type)?
| | | | +--:(dynamic)
| | | | | +--ro dynamic? empty
| | | | +--:(explicit)
| | | | +--ro explicit-path-name? string
| | | +--ro no-cspf? empty
| | | +--ro lockdown? empty
| | +--:(p2mp) {ietf-te-types:p2mp-te}?
| | +--ro p2mp-paths* [destination]
| | +--ro destination inet:ip-address
| | +--ro primary-paths* [preference]
| | +--ro preference uint8
| | +--ro path-named-constraint? string
| | +--ro path-selection
| | | +--ro topology? te-types:topology-id
| | | +--ro cost-limit? uint32
| | | +--ro hop-limit? uint8
| | | +--ro metric-type? identityref
| | | +--ro tiebreaker-type? identityref
| | | +--ro ignore-overload? boolean
| | | +--ro tunnel-path-affinities
| | | | +--ro (style)?
| | | | +--:(values)
| | | | | +--ro value? uint32
| | | | | +--ro mask? uint32
| | | | +--:(named)
| | | | +--ro constraints* [usage]
| | | | +--ro usage identityref
| | | | +--ro constraint
| | | | +--ro affinity-names* [name]
| | | | +--ro name string
| | | +--ro tunnel-path-srlgs
| | | +--ro (style)?
| | | +--:(values)
| | | | +--ro usage? identityref
| | | | +--ro values* te-types:srlg
| | | +--:(named)
| | | +--ro constraints* [usage]
| | | +--ro usage identityref
| | | +--ro constraint
| | | +--ro srlg-names* [name]
| | | +--ro name string
| | +--ro (type)?
| | | +--:(dynamic)
| | | | +--ro dynamic? empty
| | | +--:(explicit)
| | | +--ro explicit-path-name? string
| | +--ro no-cspf? empty
Saad, et al. Expires April 19, 2016 [Page 26]
Internet-Draft TE YANG Data Model October 2015
| | +--ro lockdown? empty
| | +--ro secondary-paths* [preference]
| | +--ro preference uint8
| | +--ro path-named-constraint? string
| | +--ro path-selection
| | | +--ro topology? te-types:topology-id
| | | +--ro cost-limit? uint32
| | | +--ro hop-limit? uint8
| | | +--ro metric-type? identityref
| | | +--ro tiebreaker-type? identityref
| | | +--ro ignore-overload? boolean
| | | +--ro tunnel-path-affinities
| | | | +--ro (style)?
| | | | +--:(values)
| | | | | +--ro value? uint32
| | | | | +--ro mask? uint32
| | | | +--:(named)
| | | | +--ro constraints* [usage]
| | | | +--ro usage identityref
| | | | +--ro constraint
| | | | +--ro affinity-names* [name]
| | | | +--ro name string
| | | +--ro tunnel-path-srlgs
| | | +--ro (style)?
| | | +--:(values)
| | | | +--ro usage? identityref
| | | | +--ro values* te-types:srlg
| | | +--:(named)
| | | +--ro constraints* [usage]
| | | +--ro usage identityref
| | | +--ro constraint
| | | +--ro srlg-names* [name]
| | | +--ro name string
| | +--ro (type)?
| | | +--:(dynamic)
| | | | +--ro dynamic? empty
| | | +--:(explicit)
| | | +--ro explicit-path-name? string
| | +--ro no-cspf? empty
| | +--ro lockdown? empty
| +--ro oper-status? identityref
| +--ro lsp* [source destination tunnel-id lsp-id]
| +--ro source ->
../../../../../lsps-state/lsp/source
| +--ro destination ->
../../../../../lsps-state/lsp/destination
| +--ro tunnel-id ->
../../../../../lsps-state/lsp/tunnel-id
Saad, et al. Expires April 19, 2016 [Page 27]
Internet-Draft TE YANG Data Model October 2015
| +--ro lsp-id ->
../../../../../lsps-state/lsp/lsp-id
| +--ro extended-tunnel-id? ->
../../../../../lsps-state/lsp/extended-tunnel-id
| +--ro type? ->
../../../../../lsps-state/lsp/type
Figure 8: TE tunnels configuration and state tree
3.4. TE LSPs State Data
TE LSPs are derived state data that is usually instantiated via
signaling protocols. TE LSPs exists on routers as ingress (starting
point of LSP), transit (mid-point of LSP ), or egress (termination
point of the LSP). TE LSPs are distinguished by the 5 tuple, and LSP
type (P2P or P2MP) as shown in Figure 9.
In the model, the nodes holding LSPs data exist in a read-only list
as shown below:
Saad, et al. Expires April 19, 2016 [Page 28]
Internet-Draft TE YANG Data Model October 2015
module: ietf-te
+--rw te!
+--ro lsps-state
+--ro lsp* [source destination tunnel-id lsp-id
extended-tunnel-id type]
+--ro source inet:ip-address
+--ro destination inet:ip-address
+--ro tunnel-id uint16
+--ro lsp-id uint16
+--ro extended-tunnel-id inet:ip-address
+--ro type identityref
+--ro oper-status? identityref
+--ro origin-type? enumeration
+--ro lsp-resource-status? enumeration
+--ro lsp-protection-status? enumeration
+--ro lsp-operational-status? empty
+--ro lsp-timers
| +--ro life-time? uint32
| +--ro time-to-install? uint32
| +--ro time-to-die? uint32
+--ro downstream-info
| +--ro nhop? inet:ip-address
| +--ro neighbor? inet:ip-address
| +--ro label? uint32
| +--ro outgoing-interface? if:interface-ref
+--ro upstream-info
+--ro phop? inet:ip-address
+--ro neighbor? inet:ip-address
+--ro label? uint32
+--ro incoming-interface? if:interface-ref
Figure 9: TE LSPs state tree
3.5. Global RPC Data
This branch of the model covers system-wide RPC execution data to
trigger actions and optionally expect responses. Examples of such TE
commands are to:
o Clear global TE statistics of various features
3.6. Interface RPC Data
This collection of data in the model defines TE interface RPC
execution commands. Examples of these are to:
o Clear TE statistics for all or for individual TE interfaces
Saad, et al. Expires April 19, 2016 [Page 29]
Internet-Draft TE YANG Data Model October 2015
o Trigger immediate flooding for one or all TE interfaces
3.7. Tunnel RPC Data
This branch of the model covers TE tunnel RPC execution data to
trigger actions and optionally expect responses. Examples of such TE
commands are:
o Clear statistics for all or for individual tunnels
3.8. Global Notifications Data
This branch of the model covers system-wide notifications data. The
node notifies the registered events to the server using the defined
notification messages. Example of such global TE events are:
o Backup tunnel FRR active and not-active state transition events
3.9. Interfaces Notifications Data
This branch of the model covers TE interfaces related notifications
data. The TE interface configuration is used for specific events
registration. Notifications are sent for registered events to the
server. Example events for TE interfaces are:
o Interface creation and deletion
o Interface state transitions
o (Soft) preemption triggers
o Fast reroute activation
3.10. Tunnel Notification Data
This branch of the model covers TE tunnels related notifications
data. The TE tunnels configuration is used for specific events
registration. Notifications are sent for registered events to the
server. Example events for TE tunnels are:
o Tunnel creation and deletion events
o Tunnel state up/down changes
o Tunnel state reoptimization changes
Saad, et al. Expires April 19, 2016 [Page 30]
Internet-Draft TE YANG Data Model October 2015
4. TE Generic and Helper YANG Modules
<CODE BEGINS>file "ietf-te-types@2015-10-16.yang"
module ietf-te-types {
namespace "urn:ietf:params:xml:ns:yang:ietf-te-types";
/* Replace with IANA when assigned */
prefix "te-types";
import ietf-inet-types {
prefix inet;
}
organization
"IETF TEAS Working Group";
contact "Fill me";
description
"This module contains a collection of generally
useful TE specific YANG data type defintions.";
revision 2015-10-16 {
description "Latest revision of TE basic types";
reference "RFC3209";
}
identity tunnel-type {
description
"Base identity from which specific tunnel types are
derived.";
}
identity tunnel-p2p {
base tunnel-type;
description
"TE point-to-point tunnel type.";
}
identity tunnel-p2mp {
base tunnel-type;
description
"TE point-to-multipoint tunnel type.";
}
identity state-type {
description
Saad, et al. Expires April 19, 2016 [Page 31]
Internet-Draft TE YANG Data Model October 2015
"Base identity for TE states";
}
identity state-up {
base state-type;
description
"State up";
}
identity state-down {
base state-type;
description
"State down";
}
identity switching-capabilities {
description
"Base identity for interface switching capabilities";
}
identity switching-psc1 {
base switching-capabilities;
description
"Packet-Switch Capable-1 (PSC-1)";
}
identity switching-evpl {
base switching-capabilities;
description
"Ethernet Virtual Private Line (EVPL)";
}
identity switching-l2sc {
base switching-capabilities;
description
"Layer-2 Switch Capable (L2SC)";
}
identity switching-tdm {
base switching-capabilities;
description
"Time-Division-Multiplex Capable (TDM)";
}
identity switching-otn {
base switching-capabilities;
description
"OTN-TDM capable";
Saad, et al. Expires April 19, 2016 [Page 32]
Internet-Draft TE YANG Data Model October 2015
}
identity switching-dcsc {
base switching-capabilities;
description
"Data Channel Switching Capable (DCSC)";
}
identity switching-lsc {
base switching-capabilities;
description
"Lambda-Switch Capable (LSC)";
}
identity switching-fsc {
base switching-capabilities;
description
"Fiber-Switch Capable (FSC)";
}
identity lsp-encoding-types {
description
"Base identity for encoding types";
}
identity lsp-encoding-packet {
base lsp-encoding-types;
description
"Packet LSP encoding";
}
identity lsp-encoding-ethernet {
base lsp-encoding-types;
description
"Ethernet LSP encoding";
}
identity lsp-encoding-pdh {
base lsp-encoding-types;
description
"ANSI/ETSI LSP encoding";
}
identity lsp-encoding-sdh {
base lsp-encoding-types;
description
"SDH ITU-T G.707 / SONET ANSI T1.105 LSP encoding";
}
Saad, et al. Expires April 19, 2016 [Page 33]
Internet-Draft TE YANG Data Model October 2015
identity lsp-encoding-digital-wrapper {
base lsp-encoding-types;
description
"Digital Wrapper LSP encoding";
}
identity lsp-encoding-lambda {
base lsp-encoding-types;
description
"Lambda (photonic) LSP encoding";
}
identity lsp-encoding-fiber {
base lsp-encoding-types;
description
"Fiber LSP encoding";
}
identity lsp-encoding-fiber-channel {
base lsp-encoding-types;
description
"FiberChannel LSP encoding";
}
identity lsp-encoding-oduk {
base lsp-encoding-types;
description
"G.709 ODUk (Digital Path)LSP encoding";
}
identity lsp-encoding-optical-channel {
base lsp-encoding-types;
description
"Line (e.g., 8B/10B) LSP encoding";
}
identity lsp-encoding-line {
base lsp-encoding-types;
description
"Line (e.g., 8B/10B) LSP encoding";
}
/* TE basic features */
feature p2mp-te {
description
"Indicates support for P2MP-TE";
}
Saad, et al. Expires April 19, 2016 [Page 34]
Internet-Draft TE YANG Data Model October 2015
feature frr-te {
description
"Indicates support for TE FastReroute (FRR)";
}
feature extended-admin-groups {
description
"Indicates support for TE link extended admin
groups.";
}
feature named-path-affinities {
description
"Indicates support for named path affinities";
}
feature named-extended-admin-groups {
description
"Indicates support for named extended admin groups";
}
feature named-srlg-groups {
description
"Indicates support for named SRLG groups";
}
feature named-path-constraints {
description
"Indicates support for named path constraints";
}
grouping explicit-route-subobject {
description
"The explicit route subobject grouping";
choice type {
description
"The explicit route subobject type";
case ipv4-address {
description
"IPv4 address explicit route subobject";
leaf v4-address {
type inet:ipv4-address;
description
"An IPv4 address. This address is
treated as a prefix based on the
prefix length value below. Bits beyond
the prefix are ignored on receipt and
SHOULD be set to zero on transmission.";
Saad, et al. Expires April 19, 2016 [Page 35]
Internet-Draft TE YANG Data Model October 2015
}
leaf v4-prefix-length {
type uint8;
description
"Length in bits of the IPv4 prefix";
}
leaf v4-loose {
type boolean;
description
"Describes whether the object is loose
if set, or otherwise strict";
}
}
case ipv6-address {
description
"IPv6 address Explicit Route Object";
leaf v6-address {
type inet:ipv6-address;
description
"An IPv6 address. This address is
treated as a prefix based on the
prefix length value below. Bits
beyond the prefix are ignored on
receipt and SHOULD be set to zero
on transmission.";
}
leaf v6-prefix-length {
type uint8;
description
"Length in bits of the IPv4 prefix";
}
leaf v6-loose {
type boolean;
description
"Describes whether the object is loose
if set, or otherwise strict";
}
}
case as-number {
leaf as-number {
type uint16;
description "AS number";
}
description
"Autonomous System explicit route subobject";
}
case unnumbered-link {
leaf router-id {
Saad, et al. Expires April 19, 2016 [Page 36]
Internet-Draft TE YANG Data Model October 2015
type inet:ip-address;
description
"A router-id address";
}
leaf interface-id {
type uint32;
description "The interface identifier";
}
description
"Unnumbered link explicit route subobject";
reference
"RFC3477: Signalling Unnumbered Links in
RSVP-TE";
}
case label {
leaf value {
type uint32;
description "the label value";
}
description
"The Label ERO subobject";
}
/* AS domain sequence..? */
}
}
grouping record-route-subobject {
description
"The record route subobject grouping";
choice type {
description
"The record route subobject type";
case ipv4-address {
leaf v4-address {
type inet:ipv4-address;
description
"An IPv4 address. This address is
treated as a prefix based on the prefix
length value below. Bits beyond the
prefix are ignored on receipt and
SHOULD be set to zero on transmission.";
}
leaf v4-prefix-length {
type uint8;
description
"Length in bits of the IPv4 prefix";
}
leaf v4-flags {
Saad, et al. Expires April 19, 2016 [Page 37]
Internet-Draft TE YANG Data Model October 2015
type uint8;
description
"IPv4 address sub-object flags";
reference "RFC3209";
}
}
case ipv6-address {
leaf v6-address {
type inet:ipv6-address;
description
"An IPv6 address. This address is
treated as a prefix based on the
prefix length value below. Bits
beyond the prefix are ignored on
receipt and SHOULD be set to zero
on transmission.";
}
leaf v6-prefix-length {
type uint8;
description
"Length in bits of the IPv4 prefix";
}
leaf v6-flags {
type uint8;
description
"IPv6 address sub-object flags";
reference "RFC3209";
}
}
case label {
leaf value {
type uint32;
description "the label value";
}
leaf flags {
type uint8;
description
"Label sub-object flags";
reference "RFC3209";
}
description
"The Label ERO subobject";
}
}
}
identity route-usage-type {
description
Saad, et al. Expires April 19, 2016 [Page 38]
Internet-Draft TE YANG Data Model October 2015
"Base identity for route usage";
}
identity route-include-ero {
base route-usage-type;
description
"Include ERO from route";
}
identity route-exclude-ero {
base route-usage-type;
description
"Exclude ERO from route";
}
identity route-exclude-srlg {
base route-usage-type;
description
"Exclude SRLG from route";
}
identity path-metric-type {
description
"Base identity for path metric type";
}
identity path-metric-te {
base path-metric-type;
description
"TE path metric";
}
identity path-metric-igp {
base path-metric-type;
description
"IGP path metric";
}
identity path-tiebreaker-type {
description
"Base identity for path tie-breaker type";
}
identity path-tiebreaker-minfill {
base path-tiebreaker-type;
description
"Min-Fill LSP path placement";
}
Saad, et al. Expires April 19, 2016 [Page 39]
Internet-Draft TE YANG Data Model October 2015
identity path-tiebreaker-maxfill {
base path-tiebreaker-type;
description
"Max-Fill LSP path placement";
}
identity path-tiebreaker-randoom {
base path-tiebreaker-type;
description
"Random LSP path placement";
}
identity bidir-provisioning-mode {
description
"Base identity for bidirectional provisioning
mode.";
}
identity bidir-provisioning-single-sided {
base bidir-provisioning-mode;
description
"Single-sided bidirectional provioning mode";
}
identity bidir-provisioning-double-sided {
base bidir-provisioning-mode;
description
"Double-sided bidirectional provioning mode";
}
identity bidir-association-type {
description
"Base identity for bidirectional association type";
}
identity bidir-assoc-corouted {
base bidir-association-type;
description
"Co-routed bidirectional association type";
}
identity bidir-assoc-non-corouted {
base bidir-association-type;
description
"Non co-routed bidirectional association type";
}
identity resource-affinities-type {
Saad, et al. Expires April 19, 2016 [Page 40]
Internet-Draft TE YANG Data Model October 2015
description
"Base identity for resource affinities";
}
identity resource-aff-include-all {
base resource-affinities-type;
description
"The set of attribute filters associated with a
tunnel all of which must be present for a link
to be acceptable";
}
identity resource-aff-include-any {
base resource-affinities-type;
description
"The set of attribute filters associated with a
tunnel any of which must be present for a link
to be acceptable";
}
identity resource-aff-exclude-any {
base resource-affinities-type;
description
"The set of attribute filters associated with a
tunnel any of which renders a link unacceptable";
}
typedef admin-group {
type binary {
length 32;
}
description
"Administrative group/Resource class/Color.";
}
typedef extended-admin-group {
type binary;
description
"Extended administrative group/Resource class/Color.";
}
typedef admin-groups {
type union {
type admin-group;
type extended-admin-group;
}
description "TE administrative group derived type";
}
Saad, et al. Expires April 19, 2016 [Page 41]
Internet-Draft TE YANG Data Model October 2015
typedef srlg {
type uint32;
description "SRLG type";
}
identity path-computation-srlg-type {
description
"Base identity for SRLG path computation";
}
identity srlg-ignore {
base path-computation-srlg-type;
description
"Ignores SRLGs in path computation";
}
identity srlg-strict {
base path-computation-srlg-type;
description
"Include strict SRLG check in path computation";
}
identity srlg-preferred {
base path-computation-srlg-type;
description
"Include preferred SRLG check in path computation";
}
identity srlg-weighted {
base path-computation-srlg-type;
description
"Include weighted SRLG check in path computation";
}
typedef te-metric {
type uint32;
description
"TE link metric";
}
typedef topology-id {
type string {
pattern '/?([a-zA-Z0-9\-_.]+)(/[a-zA-Z0-9\-_.]+)*';
}
description
"An identifier for a topology.";
}
Saad, et al. Expires April 19, 2016 [Page 42]
Internet-Draft TE YANG Data Model October 2015
/**
* TE tunnel generic groupings
**/
/* Tunnel path selection parameters */
grouping tunnel-path-selection {
description
"Tunnel path selection properties grouping";
container path-selection {
description
"Tunnel path selection properties container";
leaf topology {
type te-types:topology-id;
description
"The tunnel path is computed using the specific
topology identified by this identifier";
}
leaf cost-limit {
type uint32 {
range "1..4294967295";
}
description
"The tunnel path cost limit.";
}
leaf hop-limit {
type uint8 {
range "1..255";
}
description
"The tunnel path hop limit.";
}
leaf metric-type {
type identityref {
base path-metric-type;
}
default path-metric-te;
description
"The tunnel path metric type.";
}
leaf tiebreaker-type {
type identityref {
base path-tiebreaker-type;
}
default path-tiebreaker-maxfill;
description
"The tunnel path computation tie breakers.";
}
leaf ignore-overload {
Saad, et al. Expires April 19, 2016 [Page 43]
Internet-Draft TE YANG Data Model October 2015
type boolean;
description
"The tunnel path can traverse overloaded node.";
}
uses tunnel-path-affinities;
uses tunnel-path-srlgs;
}
}
grouping tunnel-path-affinities {
description
"Path affinities grouping";
container tunnel-path-affinities {
if-feature named-path-affinities;
description
"Path affinities container";
choice style {
description
"Path affinities representation style";
case values {
leaf value {
type uint32 {
range "0..4294967295";
}
description
"Affinity value";
}
leaf mask {
type uint32 {
range "0..4294967295";
}
description
"Affinity mask";
}
}
case named {
list constraints {
key "usage";
leaf usage {
type identityref {
base resource-affinities-type;
}
description "Affinities usage";
}
container constraint {
description
"Container for named affinities";
list affinity-names {
Saad, et al. Expires April 19, 2016 [Page 44]
Internet-Draft TE YANG Data Model October 2015
key "name";
leaf name {
type string;
description
"Affinity name";
}
description
"List of named affinities";
}
}
description
"List of named affinity constraints";
}
}
}
}
}
grouping tunnel-path-srlgs {
description
"Path SRLG properties grouping";
container tunnel-path-srlgs {
description
"Path SRLG properties container";
choice style {
description
"Type of SRLG representation";
case values {
leaf usage {
type identityref {
base route-exclude-srlg;
}
description "SRLG usage";
}
leaf-list values {
type te-types:srlg;
description "SRLG value";
}
}
case named {
list constraints {
key "usage";
leaf usage {
type identityref {
base route-exclude-srlg;
}
description "SRLG usage";
}
Saad, et al. Expires April 19, 2016 [Page 45]
Internet-Draft TE YANG Data Model October 2015
container constraint {
description
"Container for named SRLG list";
list srlg-names {
key "name";
leaf name {
type string;
description
"The SRLG name";
}
description
"List named SRLGs";
}
}
description
"List of named SRLG constraints";
}
}
}
}
}
grouping tunnel-bidir-assoc-properties {
description
"TE tunnel associated bidirectional properties
grouping";
container bidirectional {
description
"TE tunnel associated bidirectional attributes.";
container association {
description
"Tunnel bidirectional association properties";
leaf id {
type uint16;
description
"The TE tunnel association identifier.";
}
leaf source {
type inet:ip-address;
description
"The TE tunnel association source.";
}
leaf global-source {
type inet:ip-address;
description
"The TE tunnel association global
source.";
}
Saad, et al. Expires April 19, 2016 [Page 46]
Internet-Draft TE YANG Data Model October 2015
leaf type {
type identityref {
base bidir-association-type;
}
default bidir-assoc-non-corouted;
description
"The TE tunnel association type.";
}
leaf provisioing {
type identityref {
base bidir-provisioning-mode;
}
description
"Describes the provisioning model of the
associated bidirectional LSP";
reference
"draft-ietf-teas-mpls-tp-rsvpte-ext-
associated-lsp, section-3.2";
}
}
}
}
/*** End of TE tunnel groupings ***/
}
<CODE ENDS>
Figure 10: TE basic types YANG module
<CODE BEGINS> file "ietf-te-psc-types@2015-10-16.yang"
module ietf-te-psc-types {
namespace "urn:ietf:params:xml:ns:yang:ietf-te-psc-types";
/* Replace with IANA when assigned */
prefix "te-psc-types";
import ietf-inet-types { prefix inet; }
organization
"IETF TEAS Working Group";
contact "Fill me";
description
"This module contains a collection of generally
useful TE specific YANG data type defintions.";
Saad, et al. Expires April 19, 2016 [Page 47]
Internet-Draft TE YANG Data Model October 2015
revision 2015-10-16 {
description "Latest revision of TE MPLS/packet types";
reference "RFC3209";
}
/* Describes egress LSP label allocation */
typedef egress-label {
type enumeration {
enum "IPv4-EXPLICIT-NULL" {
description
"Use IPv4 explicit-NULL MPLS label at the
egress";
}
enum "IPv6-EXPLICIT-NULL" {
description
"Use IPv6 explicit-NULL MPLS label at the
egress";
}
enum "IMPLICIT-NULL" {
description
"Use implicit-NULL MPLS label at the egress";
}
enum "NON-NULL"{
description
"Use a non NULL MPLS label at the egress";
}
}
description
"Describes egress label allocation";
}
identity backup-type {
description
"Base identity for backup protection types";
}
identity backup-facility {
base backup-type;
description
"Use facility backup to protect LSPs traversing
protected TE interface";
reference
"RFC49090: RSVP-TE Fast Reroute";
}
identity backup-detour {
base backup-type;
description
Saad, et al. Expires April 19, 2016 [Page 48]
Internet-Draft TE YANG Data Model October 2015
"Use detour or 1-for-1 protection";
reference
"RFC49090: RSVP-TE Fast Reroute";
}
identity backup-protection-type {
description
"Base identity for backup protection type";
}
identity backup-protection-link {
base backup-protection-type;
description
"backup provides link protection only";
}
identity backup-protection-node-link {
base backup-protection-type;
description
"backup offers node (preferred) or link protection";
}
identity bc-model-type {
description
"Base identity for Diffserv-TE bandwidth constraint
model type";
}
identity bc-model-rdm {
base bc-model-type;
description
"Russian Doll bandwidth constraint model type.";
}
identity bc-model-mam {
base bc-model-type;
description
"Maximum Allocation bandwidth constraint
model type.";
}
identity bc-model-mar {
base bc-model-type;
description
"Maximum Allocation with Reservation
bandwidth constraint model type.";
}
Saad, et al. Expires April 19, 2016 [Page 49]
Internet-Draft TE YANG Data Model October 2015
grouping bandwidth-constraint-values {
description
"Packet bandwidth contraints values";
choice value-type {
description
"Value representation";
case percentages {
container perc-values {
uses bandwidth-psc-constraints;
description
"Percentage values";
}
}
case absolutes {
container abs-values {
uses bandwidth-psc-constraints;
description
"Absolute values";
}
}
}
}
grouping bandwidth-psc-reservable {
description
"Packet reservable bandwidth";
choice bandwidth-value {
description "Reservable bandwidth configuraiton choice";
case absolute {
leaf absolute-value {
type uint32;
description "Absolute value of the bandwidth";
}
}
case precentage {
leaf percent-value {
type uint32 {
range "0..4294967295";
}
description "Percentage reservable bandwidth";
}
description
"The maximum reservable bandwidth on the
interface";
}
}
choice bc-model-type {
description
Saad, et al. Expires April 19, 2016 [Page 50]
Internet-Draft TE YANG Data Model October 2015
"Reservable bandwidth percentage capacity
values.";
case bc-model-rdm {
container bc-model-rdm {
description
"Russian Doll Model Bandwidth Constraints.";
uses bandwidth-psc-constraints;
}
}
case bc-model-mam {
container bc-model-mam {
uses bandwidth-psc-constraints;
description
"Maximum Allocation Model Bandwidth
Constraints.";
}
}
case bc-model-mar {
container bc-model-mar {
uses bandwidth-psc-constraints;
description
"Maximum Allocation with Reservation Model
Bandwidth Constraints.";
}
}
}
}
typedef bfd-type {
type enumeration {
enum classical {
description "BFD classical session type.";
}
enum seamless {
description "BFD seamless session type.";
}
}
default "classical";
description
"Type of BFD session";
}
typedef bfd-encap-mode-type {
type enumeration {
enum gal {
description
"BFD with GAL mode";
}
Saad, et al. Expires April 19, 2016 [Page 51]
Internet-Draft TE YANG Data Model October 2015
enum ip {
description
"BFD with IP mode";
}
}
default ip;
description
"Possible BFD transport modes when running over TE
LSPs.";
}
grouping bandwidth-psc-constraints {
description "Bandwidth constraints.";
container bandwidth-psc-constraints {
description
"Holds the bandwidth contraints properties";
leaf maximum-reservable {
type uint32 {
range "0..4294967295";
}
description
"The maximum reservable bandwidth on the
interface";
}
leaf-list bc-value {
type uint32 {
range "0..4294967295";
}
max-elements 8;
description
"The bandwidth contraint type";
}
}
}
grouping tunnel-forwarding-properties {
description "Properties for using tunnel in forwarding.";
container forwarding {
description
"Tunnel forwarding properties container";
leaf load-share {
type uint32 {
range "1..4294967295";
}
description "ECMP tunnel forwarding
load-share factor.";
}
choice policy-type {
Saad, et al. Expires April 19, 2016 [Page 52]
Internet-Draft TE YANG Data Model October 2015
description
"Tunnel policy type";
container class {
description
"Tunnel forwarding per class properties";
leaf class {
type uint8 {
range "1..7";
}
description
"The class associated with this tunnel";
}
}
container group {
description
"Tunnel frowarding per group properties";
leaf-list classes {
type uint8 {
range "1..7";
}
description
"The forwarding class";
}
}
}
}
}
grouping tunnel-routing-properties {
description
"TE tunnel routing properties";
choice routing-choice {
description
"Announces the tunnel to IGP as either
autoroute or forwarding adjacency.";
case autoroute {
container autoroute-announce {
presence "Enable autoroute announce.";
description
"Announce the TE tunnel as autoroute to
IGP for use as IGP shortcut.";
leaf-list routing-afs {
type inet:ip-version;
description
"Address families";
}
choice metric-type {
description
Saad, et al. Expires April 19, 2016 [Page 53]
Internet-Draft TE YANG Data Model October 2015
"Type of metric to use when announcing
the tunnel as shortcut";
leaf metric {
type uint32 {
range "1..2147483647";
}
description
"Describes the metric to use when
announcing the tunnel as shortcut";
}
leaf relative-metric {
type int32 {
range "-10..10";
}
description
"Relative TE metric to use when
announcing the tunnel as shortcut";
}
leaf absolute-metric {
type uint32 {
range "1..2147483647";
}
description
"Absolute TE metric to use when
announcing the tunnel as shortcut";
}
}
}
}
case forwarding-adjacency {
container forwarding-adjacency {
presence "Enable forwarding adjacency
on the tunnel.";
description
"Announce the TE tunnel
as forwarding adjacency.";
leaf holdtime {
type uint32 {
range "0..4294967295";
}
description
"Holdtime in seconds after
tunnel becomes UP.";
}
leaf-list routing-afs {
type inet:ip-version;
description
"Address families";
Saad, et al. Expires April 19, 2016 [Page 54]
Internet-Draft TE YANG Data Model October 2015
}
}
}
}
}
}
<CODE ENDS>
Figure 11: TE packet/MPLS specific types YANG module
<CODE BEGINS> file "ietf-te@2015-10-16.yang"
module ietf-te {
namespace "urn:ietf:params:xml:ns:yang:ietf-te";
/* Replace with IANA when assigned */
prefix "te";
/* Import TE generic types */
import ietf-te-types {
prefix ietf-te-types;
}
/* Import TE packet specific types */
import ietf-te-psc-types {
prefix ietf-te-psc-types;
}
import ietf-interfaces {
prefix if;
}
import ietf-inet-types {
prefix inet;
}
organization
"IETF TEAS Working Group";
contact
"Fill me";
description
"YANG data module for TE configuration,
state, RPC and notifications.";
Saad, et al. Expires April 19, 2016 [Page 55]
Internet-Draft TE YANG Data Model October 2015
revision 2015-10-16 {
description "Latest update to TE generic YANG module.";
reference "TBD";
}
/**
* TE interface generic groupings
*/
grouping te-admin-groups_config {
description
"TE interface affinities grouping";
choice admin-group-type {
description
"TE interface administrative groups
representation type";
case value-admin-groups {
choice value-admin-group-type {
description "choice of admin-groups";
case value-admin-groups {
description
"Administrative group/Resource
class/Color.";
leaf admin-group {
type ietf-te-types:admin-group;
description
"TE interface administrative group";
}
}
case value-extended-admin-groups {
if-feature ietf-te-types:extended-admin-groups;
description
"Extended administrative group/Resource
class/Color.";
leaf extended-admin-group {
type ietf-te-types:extended-admin-group;
description
"TE interface extended administrativei
group";
}
}
}
}
case named-admin-groups {
list named-admin-groups {
if-feature ietf-te-types:extended-admin-groups;
if-feature ietf-te-types:named-extended-admin-groups;
key named-admin-group;
description
Saad, et al. Expires April 19, 2016 [Page 56]
Internet-Draft TE YANG Data Model October 2015
"A list of named admin-group entries";
leaf named-admin-group {
type leafref {
path "../../../../../globals/config/" +
"named-admin-groups/name";
}
description
"A named admin-group entry";
}
}
}
}
}
/* TE interface SRLGs */
grouping te-srlgs_config {
description "TE interface SRLG grouping";
choice srlg-type {
description "Choice of SRLG configuration";
case value-srlgs {
list values {
key "value";
description "List of SRLG values that
this link is part of.";
leaf value {
type uint32 {
range "0..4294967295";
}
description
"Value of the SRLG";
}
}
}
case named-srlgs {
list named-srlgs {
if-feature ietf-te-types:named-srlg-groups;
key named-srlg;
description
"A list of named SRLG entries";
leaf named-srlg {
type leafref {
path "../../../../../globals/config/" +
"named-srlgs/name";
}
description
"A named SRLG entry";
}
}
Saad, et al. Expires April 19, 2016 [Page 57]
Internet-Draft TE YANG Data Model October 2015
}
}
}
/* TE interface flooding parameters */
grouping te-flooding-parameters_config {
description "Interface TE flooding properties.";
container thresholds {
description "Flooding threshold values in percentages.";
choice type {
description
"Describes the flooding threshold step method";
case equal-steps {
choice equal-step-type {
description
"Describes whether up and down equal step
size are same or different";
case up-down-different-step {
leaf up-step {
type uint8 {
range "0..100";
}
description
"Set single percentage threshold
for increasing resource
allocation";
}
leaf down-step {
type uint8 {
range "0..100";
}
description
"Set single percentage threshold
for decreasing resource
allocation";
}
}
case up-down-same-step {
leaf step {
type uint8 {
range "0..100";
}
description
"Set single percentage threshold
for increasing and decreasing
resource allocation";
}
}
Saad, et al. Expires April 19, 2016 [Page 58]
Internet-Draft TE YANG Data Model October 2015
}
}
case unequal-steps {
list up-steps {
key "value";
description
"Set nultuple percentage thresholds for
increasing resource allocation";
leaf value {
type uint8 {
range "0..100";
}
description
"Percentage value";
}
}
list down-steps {
key "value";
description
"Set nultuple percentage thresholds for
decreasing resource allocation";
leaf value {
type uint8 {
range "0..100";
}
description
"Percentage value";
}
}
}
}
}
}
/* TE interface metric */
grouping te-metric_config {
description "Interface TE metric grouping";
leaf te-metric {
type ietf-te-types:te-metric;
description "Interface TE metric.";
}
}
/* TE interface switching capabilities */
grouping te-switching-cap_config {
description
"TE interface switching capabilities";
list switching-capabilities {
Saad, et al. Expires April 19, 2016 [Page 59]
Internet-Draft TE YANG Data Model October 2015
key "switching-capability";
description
"List of interface capabilities for this interface";
leaf switching-capability {
type identityref {
base ietf-te-types:switching-capabilities;
}
description
"Switching Capability for this interface";
}
leaf encoding {
type identityref {
base ietf-te-types:lsp-encoding-types;
}
description
"Encoding supported by this interface";
}
}
}
grouping te-advertisements_state {
description
"TE interface advertisements state grouping";
container te-advertisements_state {
description
"TE interface advertisements state container";
leaf flood-interval {
type uint32;
description
"The periodic flooding interval";
}
leaf last-flooded-time {
type uint32;
units seconds;
description
"Time elapsed since last flooding in seconds";
}
leaf next-flooded-time {
type uint32;
units seconds;
description
"Time remained for next flooding in seconds";
}
leaf last-flooded-trigger {
type enumeration {
enum link-up {
description "Link-up flooding trigger";
}
Saad, et al. Expires April 19, 2016 [Page 60]
Internet-Draft TE YANG Data Model October 2015
enum link-down {
description "Link-up flooding trigger";
}
enum threshold-up {
description
"Bandwidth reservation up threshold";
}
enum threshold-down {
description
"Bandwidth reservation down threshold";
}
enum bandwidth-change {
description "Banwidth capacity change";
}
enum user-initiated {
description "Initiated by user";
}
enum srlg-change {
description "SRLG property change";
}
enum periodic-timer {
description "Periodic timer expired";
}
}
description "Trigger for the last flood";
}
list advertized-level-areas {
key level-area;
description
"List of areas the TE interface is advertised
in";
leaf level-area {
type uint32;
description
"The IGP area or level where the TE
interface state is advertised in";
}
}
}
}
/* TE interface attributes grouping */
grouping te-attributes {
description "TE attributes configuration grouping";
container config {
description
"Configuration parameters for interface TE
attributes";
Saad, et al. Expires April 19, 2016 [Page 61]
Internet-Draft TE YANG Data Model October 2015
uses te-metric_config;
uses te-admin-groups_config;
uses te-srlgs_config;
uses te-switching-cap_config;
uses te-flooding-parameters_config;
}
container state {
config false;
description
"State parameters for interface TE metric";
uses te-metric_config;
uses te-admin-groups_config;
uses te-srlgs_config;
uses te-switching-cap_config;
uses te-flooding-parameters_config;
uses te-advertisements_state;
}
}
grouping te-all-attributes {
description
"TE attributes configuration grouping for all
interfaces";
container config {
description
"Configuration parameters for all interface TE
attributes";
uses te-flooding-parameters_config;
}
container state {
config false;
description
"State parameters for all interface TE metric";
uses te-flooding-parameters_config;
}
}
/*** End of TE interface groupings ***/
/**
* TE tunnel generic groupings
*/
/* TE tunnel path configuration data */
grouping tunnel-path-params_config {
description
"Tunnel path properties grouping";
leaf path-named-constraint {
if-feature ietf-te-types:named-path-constraints;
Saad, et al. Expires April 19, 2016 [Page 62]
Internet-Draft TE YANG Data Model October 2015
type string;
description
"Reference to a globally defined named path
constraint set";
}
uses ietf-te-types:tunnel-path-selection;
choice type {
description
"Describes the path type";
case dynamic {
leaf dynamic {
type empty;
description
"A CSPF dynamically computed path";
}
}
case explicit {
leaf explicit-path-name {
type string;
description
"The explicit-path name";
}
}
}
leaf no-cspf {
type empty;
description
"Indicates no CSPF is to be attempted on this
path.";
}
leaf lockdown {
type empty;
description
"Indicates no reoptimization to be attempted for
this path.";
}
}
/* TE tunne configuration data */
grouping tunnel-params_config {
description
"Configuration parameters relating to TE tunnel";
leaf description {
type string;
description
"TE tunnel description.";
}
leaf admin-status {
Saad, et al. Expires April 19, 2016 [Page 63]
Internet-Draft TE YANG Data Model October 2015
type identityref {
base ietf-te-types:state-type;
}
default ietf-te-types:state-up;
description "TE tunnel administrative state.";
}
uses ietf-te-psc-types:tunnel-routing-properties;
uses ietf-te-psc-types:tunnel-forwarding-properties;
uses ietf-te-types:tunnel-bidir-assoc-properties;
choice path-type {
description
"Describes the path type";
case p2p {
leaf destination {
type inet:ip-address;
description
"P2P tunnel destination address";
}
/* P2P list of path(s) */
list primary-paths {
key "preference";
description
"List of primary paths for this
tunnel.";
leaf preference {
type uint8 {
range "1..255";
}
description
"Specifies a preference for
this path. The lower the
number higher the
preference";
}
uses tunnel-path-params_config;
list secondary-paths {
key "preference";
description
"List of secondary paths for this
tunnel.";
leaf preference {
type uint8 {
range "1..255";
}
description
"Specifies a preference for
this path. The lower the
number higher the
Saad, et al. Expires April 19, 2016 [Page 64]
Internet-Draft TE YANG Data Model October 2015
preference";
}
uses tunnel-path-params_config;
}
}
}
case p2mp {
if-feature ietf-te-types:p2mp-te;
list p2mp-paths {
key "destination";
description
"List of destinations and their
paths.";
leaf destination {
type inet:ip-address;
description
"P2MP destination leaf address";
}
list primary-paths {
key "preference";
description
"List of primary paths";
leaf preference {
type uint8 {
range "1..255";
}
description
"Specifies a preference for
this path. The lower the
number higher the
preference";
}
uses tunnel-path-params_config;
list secondary-paths {
key "preference";
description
"List of secondary paths";
leaf preference {
type uint8 {
range "1..255";
}
description
"Specifies a preference
for this path. The lower
the number higher
the preference";
}
uses tunnel-path-params_config;
Saad, et al. Expires April 19, 2016 [Page 65]
Internet-Draft TE YANG Data Model October 2015
}
}
}
}
}
}
grouping tunnel-params_state {
description
"State parameters relating to TE tunnel";
leaf oper-status {
type identityref {
base ietf-te-types:state-type;
}
description "TE tunnel operational state.";
}
list lsp {
key "source destination tunnel-id lsp-id";
description "List of LSPs associated with the tunnel.";
leaf source {
type leafref {
path "../../../../../lsps-state/lsp/source";
}
description
"Tunnel sender address extracted from
SENDER_TEMPLATE object";
reference "RFC3209";
}
leaf destination {
type leafref {
path "../../../../../lsps-state/lsp/destination";
}
description
"Tunnel endpoint address extracted from
SESSION object";
reference "RFC3209";
}
leaf tunnel-id {
type leafref {
path "../../../../../lsps-state/lsp/tunnel-id";
}
description
"Tunnel identifier used in the SESSION
that remains constant over the life
of the tunnel.";
reference "RFC3209";
}
Saad, et al. Expires April 19, 2016 [Page 66]
Internet-Draft TE YANG Data Model October 2015
leaf lsp-id {
type leafref {
path "../../../../../lsps-state/lsp/lsp-id";
}
description
"Identifier used in the SENDER_TEMPLATE
and the FILTER_SPEC that can be changed
to allow a sender to share resources with
itself.";
reference "RFC3209";
}
leaf extended-tunnel-id {
type leafref {
path "../../../../../lsps-state/lsp/extended-tunnel-id";
}
description
"Extended Tunnel ID of the LSP.";
reference "RFC3209";
}
leaf type {
type leafref {
path "../../../../../lsps-state/lsp/type";
}
description "LSP type P2P or P2MP";
}
}
}
/* TE tunnel configuration/state grouping */
grouping tunnel-properties {
description
"Top level grouping for tunnel properties.";
container config {
description
"Configuration parameters relating to
tunnel properties";
uses tunnel-params_config;
}
container state {
config false;
description
"State information associated with tunnel
properties";
uses tunnel-params_config;
uses tunnel-params_state;
}
}
/*** End of TE tunnel groupings ***/
Saad, et al. Expires April 19, 2016 [Page 67]
Internet-Draft TE YANG Data Model October 2015
/**
* LSP related generic groupings
*/
grouping lsp-properties_state {
description
"State parameters relating to LSP";
leaf oper-status {
type identityref {
base ietf-te-types:state-type;
}
description "LSP operational state.";
}
leaf origin-type {
type enumeration {
enum ingress {
description
"Origin ingress";
}
enum egress {
description
"Origin egress";
}
enum transit {
description
"transit";
}
}
description
"Origin type of LSP relative to the location
of the local switch in the path.";
}
leaf lsp-resource-status {
type enumeration {
enum primary {
description
"A primary LSP is a fully established LSP for
which the resource allocation has been committed
at the data plane";
}
enum secondary {
description
"A secondary LSP is an LSP that has been provisioned
in the control plane only; e.g. resource allocation
has not been committed at the data plane";
}
Saad, et al. Expires April 19, 2016 [Page 68]
Internet-Draft TE YANG Data Model October 2015
}
description "LSP resource allocation type";
reference "rfc4872, section 4.2.1";
}
leaf lsp-protection-status {
type enumeration {
enum working {
description
"A working LSP must be a primary LSP whilst a protecting
LSP can be either a primary or a secondary LSP. Also,
known as protected LSPs when working LSPs are associated
with protecting LSPs.";
}
enum protecting {
description
"A secondary LSP is an LSP that has been provisioned
in the control plane only; e.g. resource allocation
has not been committed at the data plane";
}
}
description "LSP role type";
reference "rfc4872, section 4.2.1";
}
leaf lsp-operational-status {
type empty;
description
"This bit is set when a protecting LSP is carrying the normal
traffic after protection switching";
}
container lsp-timers {
when "../origin-type = 'ingress'" {
description "Applicable to ingress LSPs only";
}
description "Ingress LSP timers";
leaf life-time {
type uint32;
units seconds;
description
"lsp life time";
}
leaf time-to-install {
type uint32;
units seconds;
description
Saad, et al. Expires April 19, 2016 [Page 69]
Internet-Draft TE YANG Data Model October 2015
"lsp installation delay time";
}
leaf time-to-die {
type uint32;
units seconds;
description
"lsp expire delay time";
}
}
container downstream-info {
when "../../origin-type != 'egress'" {
description "Applicable to ingress LSPs only";
}
description
"downstream information";
leaf nhop {
type inet:ip-address;
description
"downstream nexthop.";
}
leaf neighbor {
type inet:ip-address;
description
"downstream neighbor.";
}
leaf label {
type uint32;
description
"downstream label.";
}
}
container upstream-info {
when "../../origin-type != 'ingress'" {
description "Applicable to ingress LSPs only";
}
description
"upstream information";
leaf phop {
type inet:ip-address;
description
"upstream nexthop or previous-hop.";
Saad, et al. Expires April 19, 2016 [Page 70]
Internet-Draft TE YANG Data Model October 2015
}
leaf neighbor {
type inet:ip-address;
description
"upstream neighbor.";
}
leaf label {
type uint32;
description
"upstream label.";
}
}
}
/*** End of TE LSP groupings ***/
/**
* TE global generic groupings
*/
/* Global device specific configuration data */
grouping globals-device_config {
description
"Top level grouping for global config data.";
leaf lsp-install-interval {
type uint32;
units seconds;
description
"lsp installation delay time";
}
leaf lsp-cleanup-interval {
type uint32;
units seconds;
description
"lsp cleanup delay time";
}
}
/* Global device specific state data */
grouping globals-device_state {
description
"Top level grouping for global state data.";
leaf tunnels-counter {
type uint32;
description "Tunnels count";
}
leaf lsps-counter {
Saad, et al. Expires April 19, 2016 [Page 71]
Internet-Draft TE YANG Data Model October 2015
type uint32;
description "Tunnels count";
}
}
/* Global named admin-groups configuration data */
grouping named-admin-groups_config {
description
"Global named administrative groups configuration
grouping";
list named-admin-groups {
if-feature ietf-te-types:extended-admin-groups;
if-feature ietf-te-types:named-extended-admin-groups;
key "name";
description
"List of named TE admin-groups";
leaf name {
type string;
description
"A string name that uniquely identifies a TE
interface named admin-group";
}
leaf group {
type ietf-te-types:admin-groups;
description
"An administrative group value";
}
}
}
/* Global named admin-srlgs configuration data */
grouping named-srlgs_config {
description
"Global named SRLGs configuration
grouping";
list named-srlgs {
if-feature ietf-te-types:named-srlg-groups;
key "name";
description
"A list of named SRLG groups";
leaf name {
type string;
description
"A string name that uniquely identifies a TE
interface named srlg";
}
leaf group {
type ietf-te-types:srlg;
Saad, et al. Expires April 19, 2016 [Page 72]
Internet-Draft TE YANG Data Model October 2015
description "An SRLG value";
}
}
}
/* Global named explicit-paths configuration data */
grouping named-explicit-paths_config {
description
"Global explicit path configuration
grouping";
list named-explicit-paths {
key "name";
description
"A list of explicit paths";
leaf name {
type string;
description
"A string name that uniquely identifies an
explicit path";
}
list explicit-route-objects {
key "index";
description
"List of explicit route objects";
leaf index {
type uint8 {
range "0..255";
}
description
"Index of this explicit route object";
}
uses ietf-te-types:explicit-route-subobject;
leaf explicit-route-usage {
type identityref {
base ietf-te-types:route-usage-type;
}
description
"An IP hop action.";
}
}
}
}
/* Global named paths constraints configuration data */
grouping named-path-constraints_config {
description
"Global named path constraints configuration
grouping";
Saad, et al. Expires April 19, 2016 [Page 73]
Internet-Draft TE YANG Data Model October 2015
list named-constraints {
if-feature ietf-te-types:named-path-constraints;
key "name";
description
"A list of named path constraints";
leaf name {
type string;
description
"A string name that uniquely identifies a
path constraint set";
}
uses ietf-te-types:tunnel-path-selection;
}
}
/* TE globals container data */
grouping globals-grouping {
description
"Globals TE system-wide configuration data grouping";
container globals {
description
"Globals TE system-wide configuration data container";
container config {
description
"Configuration parameters for system-wide
parameters";
uses named-admin-groups_config;
uses named-srlgs_config;
uses named-explicit-paths_config;
uses named-path-constraints_config;
}
container state {
config false;
description
"State for system-wide parameters";
uses named-admin-groups_config;
uses named-srlgs_config;
uses named-explicit-paths_config;
uses named-path-constraints_config;
}
}
}
/* TE interface container data */
grouping interfaces-grouping {
description
"Interface TE configuration data grouping";
container interfaces {
Saad, et al. Expires April 19, 2016 [Page 74]
Internet-Draft TE YANG Data Model October 2015
description
"Configuration data model for TE interfaces.";
uses te-all-attributes;
list interface {
key "interface";
description "TE interfaces.";
leaf interface {
type if:interface-ref;
description
"TE interface name.";
}
/* TE interface parameters */
uses te-attributes;
}
}
}
/* TE tunnels container data */
grouping tunnels-grouping {
description
"Tunnels TE configuration data grouping";
container tunnels {
description
"Tunnels TE configuration data container";
list tunnel {
key "name type";
unique "identifier";
description "TE tunnel.";
leaf name {
type string;
description "TE tunnel name.";
}
leaf type {
type identityref {
base ietf-te-types:tunnel-type;
}
description "TE tunnel type.";
}
leaf identifier {
type uint16;
description
"TE tunnel Identifier.";
}
uses tunnel-properties;
}
}
}
Saad, et al. Expires April 19, 2016 [Page 75]
Internet-Draft TE YANG Data Model October 2015
/* TE LSPs ephemeral state container data */
grouping lsps-state-grouping {
description
"LSPs state operational data grouping";
container lsps-state {
config "false";
description "LSPs operational state data.";
list lsp {
key
"source destination tunnel-id lsp-id "+
"extended-tunnel-id type";
description
"List of LSPs associated with the tunnel.";
leaf source {
type inet:ip-address;
description
"Tunnel sender address extracted from
SENDER_TEMPLATE object";
reference "RFC3209";
}
leaf destination {
type inet:ip-address;
description
"Tunnel endpoint address extracted from
SESSION object";
reference "RFC3209";
}
leaf tunnel-id {
type uint16;
description
"Tunnel identifier used in the SESSION
that remains constant over the life
of the tunnel.";
reference "RFC3209";
}
leaf lsp-id {
type uint16;
description
"Identifier used in the SENDER_TEMPLATE
and the FILTER_SPEC that can be changed
to allow a sender to share resources with
itself.";
reference "RFC3209";
}
leaf extended-tunnel-id {
type inet:ip-address;
description
Saad, et al. Expires April 19, 2016 [Page 76]
Internet-Draft TE YANG Data Model October 2015
"Extended Tunnel ID of the LSP.";
reference "RFC3209";
}
leaf type {
type identityref {
base ietf-te-types:tunnel-type;
}
description "The LSP type P2P or P2MP";
}
uses lsp-properties_state;
}
}
}
/*** End of TE global groupings ***/
/**
* TE configurations container
*/
container te {
presence "Enable TE feature.";
description
"TE global container.";
/* TE Global Configuration Data */
uses globals-grouping;
/* TE Interface Configuration Data */
uses interfaces-grouping;
/* TE Tunnel Configuration Data */
uses tunnels-grouping;
/* TE LSPs State Data */
uses lsps-state-grouping;
}
/* TE Global RPCs/execution Data */
rpc globals-rpc {
description
"Execution data for TE global.";
}
/* TE interfaces RPCs/execution Data */
rpc interfaces-rpc {
description
"Execution data for TE interfaces.";
}
Saad, et al. Expires April 19, 2016 [Page 77]
Internet-Draft TE YANG Data Model October 2015
/* TE Tunnel RPCs/execution Data */
rpc tunnels-rpc {
description
"TE tunnels RPC nodes";
}
/**
* Augmentations for TE device-specific parameters
*/
/* Globals augmentation */
augment "/te/globals/config" {
description
"Global TE device specific configuration parameters";
uses globals-device_config;
}
augment "/te/globals/state" {
description
"Global TE device specific state parameters";
uses globals-device_config;
uses globals-device_state;
}
/* LSPs state augmentation */
augment "/te/lsps-state/lsp/downstream-info" {
description
"LSP device dependent downstream info augmentation";
leaf outgoing-interface {
type if:interface-ref;
description
"downstream interface.";
}
}
augment "/te/lsps-state/lsp/upstream-info" {
description
"LSP device dependent upstream info augmentation";
leaf incoming-interface {
type if:interface-ref;
description
"upstream interface.";
}
}
/* TE Global Notification Data */
notification globals-notif {
description
"Notification messages for Global TE.";
Saad, et al. Expires April 19, 2016 [Page 78]
Internet-Draft TE YANG Data Model October 2015
}
/* TE Interfaces Notification Data */
notification interfaces-notif {
description
"Notification messages for TE interfaces.";
}
/* TE Tunnel Notification Data */
notification tunnels-notif {
description
"Notification messages for TE tunnels.";
}
}
<CODE ENDS>
Figure 12: TE generic YANG module
5. IANA Considerations
This document registers the following URIs in the IETF XML registry
[RFC3688]. Following the format in [RFC3688], the following
registration is requested to be made.
URI: urn:ietf:params:xml:ns:yang:ietf-te XML: N/A, the requested URI
is an XML namespace.
URI: urn:ietf:params:xml:ns:yang:ietf-te-types XML: N/A, the
requested URI is an XML namespace.
URI: urn:ietf:params:xml:ns:yang:ietf-te-psc-types XML: N/A, the
requested URI is an XML namespace.
This document registers a YANG module in the YANG Module Names
registry [RFC6020].
name: ietf-te namespace: urn:ietf:params:xml:ns:yang:ietf-te prefix:
ietf-te reference: RFC3209
name: ietf-te-types namespace: urn:ietf:params:xml:ns:yang:ietf-te-
types prefix: ietf-te-types reference: RFC3209
name: ietf-te-psc-types namespace: urn:ietf:params:xml:ns:yang:ietf-
te-psc-types prefix: ietf-te-psc-types reference: RFC3209
Saad, et al. Expires April 19, 2016 [Page 79]
Internet-Draft TE YANG Data Model October 2015
6. Security Considerations
The YANG module defined in this memo is designed to be accessed via
the NETCONF protocol [RFC6241]. The lowest NETCONF layer is the
secure transport layer and the mandatory-to-implement secure
transport is SSH [RFC6242]. The NETCONF access control model
[RFC6536] provides means to restrict access for particular NETCONF
users to a pre-configured subset of all available NETCONF protocol
operations and content.
There are a number of data nodes defined in the YANG module which are
writable/creatable/deletable (i.e., config true, which is the
default). These data nodes may be considered sensitive or vulnerable
in some network environments. Write operations (e.g., <edit-config>)
to these data nodes without proper protection can have a negative
effect on network operations. Following are the subtrees and data
nodes and their sensitivity/vulnerability:
"/te/globals": This module specifies the global TE configurations on
a device. Unauthorized access to this container could cause the
device to ignore packets it should receive and process.
"/te/tunnels": This list specifies the configured TE tunnels on a
device. Unauthorized access to this list could cause the device to
ignore packets it should receive and process.
"/te/interfaces": This list specifies the configured TE interfaces on
a device. Unauthorized access to this list could cause the device to
ignore packets it should receive and process.
7. Acknowledgement
The authors would like to thank Lou Berger for reviewing and
providing valuable feedback on this document.
8. References
8.1. Normative References
[I-D.ietf-netmod-routing-cfg]
Lhotka, L. and A. Lindem, "A YANG Data Model for Routing
Management", draft-ietf-netmod-routing-cfg-20 (work in
progress), October 2015.
Saad, et al. Expires April 19, 2016 [Page 80]
Internet-Draft TE YANG Data Model October 2015
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/
RFC2119, March 1997,
<http://www.rfc-editor.org/info/rfc2119>.
[RFC3209] Awduche, D., Berger, L., Gan, D., Li, T., Srinivasan, V.,
and G. Swallow, "RSVP-TE: Extensions to RSVP for LSP
Tunnels", RFC 3209, DOI 10.17487/RFC3209, December 2001,
<http://www.rfc-editor.org/info/rfc3209>.
[RFC3688] Mealling, M., "The IETF XML Registry", BCP 81, RFC 3688,
DOI 10.17487/RFC3688, January 2004,
<http://www.rfc-editor.org/info/rfc3688>.
[RFC6020] Bjorklund, M., Ed., "YANG - A Data Modeling Language for
the Network Configuration Protocol (NETCONF)", RFC 6020,
DOI 10.17487/RFC6020, October 2010,
<http://www.rfc-editor.org/info/rfc6020>.
[RFC6241] Enns, R., Ed., Bjorklund, M., Ed., Schoenwaelder, J., Ed.,
and A. Bierman, Ed., "Network Configuration Protocol
(NETCONF)", RFC 6241, DOI 10.17487/RFC6241, June 2011,
<http://www.rfc-editor.org/info/rfc6241>.
[RFC6242] Wasserman, M., "Using the NETCONF Protocol over Secure
Shell (SSH)", RFC 6242, DOI 10.17487/RFC6242, June 2011,
<http://www.rfc-editor.org/info/rfc6242>.
[RFC6536] Bierman, A. and M. Bjorklund, "Network Configuration
Protocol (NETCONF) Access Control Model", RFC 6536, DOI
10.17487/RFC6536, March 2012,
<http://www.rfc-editor.org/info/rfc6536>.
[RFC6991] Schoenwaelder, J., Ed., "Common YANG Data Types", RFC
6991, DOI 10.17487/RFC6991, July 2013,
<http://www.rfc-editor.org/info/rfc6991>.
8.2. Informative References
[I-D.openconfig-mpls-consolidated-model]
George, J., Fang, L., eric.osborne@level3.com, e., and R.
Shakir, "MPLS / TE Model for Service Provider Networks",
draft-openconfig-mpls-consolidated-model-01 (work in
progress), July 2015.
Saad, et al. Expires April 19, 2016 [Page 81]
Internet-Draft TE YANG Data Model October 2015
[I-D.openconfig-netmod-opstate]
Shakir, R., Shaikh, A., and M. Hines, "Consistent Modeling
of Operational State Data in YANG", draft-openconfig-
netmod-opstate-01 (work in progress), July 2015.
[RFC3473] Berger, L., Ed., "Generalized Multi-Protocol Label
Switching (GMPLS) Signaling Resource ReserVation Protocol-
Traffic Engineering (RSVP-TE) Extensions", RFC 3473, DOI
10.17487/RFC3473, January 2003,
<http://www.rfc-editor.org/info/rfc3473>.
[RFC4328] Papadimitriou, D., Ed., "Generalized Multi-Protocol Label
Switching (GMPLS) Signaling Extensions for G.709 Optical
Transport Networks Control", RFC 4328, DOI 10.17487/
RFC4328, January 2006,
<http://www.rfc-editor.org/info/rfc4328>.
Authors' Addresses
Tarek Saad (editor)
Cisco Systems Inc
Email: tsaad@cisco.com
Rakesh Gandhi
Cisco Systems Inc
Email: rgandhi@cisco.com
Xufeng Liu
Ericsson
Email: xufeng.liu@ericsson.com
Vishnu Pavan Beeram
Juniper Networks
Email: vbeeram@juniper.net
Himanshu Shah
Ciena
Email: hshah@ciena.com
Saad, et al. Expires April 19, 2016 [Page 82]
Internet-Draft TE YANG Data Model October 2015
Xia Chen
Huawei Technologies
Email: jescia.chenxia@huawei.com
Raqib Jones
Brocade
Email: raqib@Brocade.com
Bin Wen
Comcast
Email: Bin_Wen@cable.comcast.com
Saad, et al. Expires April 19, 2016 [Page 83]