Bundle Protocol Security Application Data Model
draft-birrane-dtn-adm-bpsec-01

Document Type Active Internet-Draft (individual)
Last updated 2018-07-02
Stream (None)
Intended RFC status (None)
Formats plain text xml pdf html bibtex
Stream Stream state (No stream defined)
Consensus Boilerplate Unknown
RFC Editor Note (None)
IESG IESG state I-D Exists
Telechat date
Responsible AD (None)
Send notices to (None)
Delay-Tolerant Networking                                     E. Birrane
Internet-Draft                                               E. DiPietro
Intended status: Experimental                                   D. Linko
Expires: January 3, 2019        Johns Hopkins Applied Physics Laboratory
                                                            July 2, 2018

            Bundle Protocol Security Application Data Model
                     draft-birrane-dtn-adm-bpsec-01

Abstract

   This document describes the Application Data Model (ADM) for the
   Bundle Protocol Security (BPSEC) in compliance with the template
   provided by [I-D.birrane-dtn-adm].

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at https://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on January 3, 2019.

Copyright Notice

   Copyright (c) 2018 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (https://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Birrane, et al.          Expires January 3, 2019                [Page 1]
Internet-Draft                  BPSEC ADM                      July 2018

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   2
     1.1.  Technical Notes . . . . . . . . . . . . . . . . . . . . .   2
     1.2.  Scope . . . . . . . . . . . . . . . . . . . . . . . . . .   3
     1.3.  Requirements Language . . . . . . . . . . . . . . . . . .   3
   2.  Structure and Design of this ADM  . . . . . . . . . . . . . .   3
   3.  Naming and Identification . . . . . . . . . . . . . . . . . .   4
     3.1.  Namespace and Nicknames . . . . . . . . . . . . . . . . .   4
   4.  BPSEC Agent ADM JSON Encoding . . . . . . . . . . . . . . . .   5
   5.  IANA Considerations . . . . . . . . . . . . . . . . . . . . .  23
   6.  References  . . . . . . . . . . . . . . . . . . . . . . . . .  23
     6.1.  Informative References  . . . . . . . . . . . . . . . . .  23
     6.2.  Normative References  . . . . . . . . . . . . . . . . . .  23
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  23

1.  Introduction

   An Application Data Model (ADM) provides a guaranteed interface for
   the management of an application or protocol in accordance with the
   Asynchronous Management Architecture (AMA) defined in
   [I-D.birrane-dtn-ama].  This document is in compliance with the
   template provided by [I-D.birrane-dtn-adm].

   BPSEC ([I-D.ietf-dtn-bpsec]) defines integrity and confidentiality
   mechanisms for securing extension blocks within a Bundle Protocol
   bundle.  The BPSEC Agent ADM provides the set of information used to
   monitor and configure common aspects of any BPSEC software
   implementation.

1.1.  Technical Notes

   o  This document describes Version 1.0 of the BPSEC Agent ADM.

   o  The Asynchronous Resource Identifier (ARI) for this ADM is NOT
      correctly set.  A sample ARI is used in this version of the
      specification and MAY change in future versions of this ADM until
      an ARI registry is established.  This notice will be removed at
      that time.

   o  Agent applications MAY choose to ignore the name, description, or
      other annotative information associated with the component
      definitions within this ADM where such items are only used to
      provide human-readable information or are otherwise not necessary
      to manage a device.

Birrane, et al.          Expires January 3, 2019                [Page 2]
Internet-Draft                  BPSEC ADM                      July 2018

1.2.  Scope

   This ADM specifies those components of the Asynchronous Management
   Model (AMM) common to the BPSEC management of any instance of a BPA.

   Any Manager software implementing this ADM MUST perform the
   responsibilities of an AMA Manager as outlined in
   [I-D.birrane-dtn-adm] as they relate to the objects included in this
Show full document text