L-band Digital Aeronautical Communications System (LDACS)
draft-ietf-raw-ldacs-06
The information below is for an old version of the document.
| Document | Type |
This is an older version of an Internet-Draft that was ultimately published as RFC 9372.
|
|
|---|---|---|---|
| Authors | Nils Mäurer , Thomas Gräupl , Corinna Schmitt | ||
| Last updated | 2021-01-25 | ||
| Replaces | draft-maeurer-raw-ldacs | ||
| RFC stream | Internet Engineering Task Force (IETF) | ||
| Formats | |||
| Reviews |
GENART IETF Last Call review
(of
-10)
by Dale Worley
Ready w/issues
|
||
| Additional resources | Mailing list discussion | ||
| Stream | WG state | WG Document | |
| Associated WG milestones |
|
||
| Document shepherd | (None) | ||
| IESG | IESG state | Became RFC 9372 (Informational) | |
| Consensus boilerplate | Unknown | ||
| Telechat date | (None) | ||
| Responsible AD | (None) | ||
| Send notices to | (None) |
draft-ietf-raw-ldacs-06
RAW N. Maeurer, Ed.
Internet-Draft T. Graeupl, Ed.
Intended status: Informational German Aerospace Center (DLR)
Expires: 29 July 2021 C. Schmitt, Ed.
Research Institute CODE, UniBwM
25 January 2021
L-band Digital Aeronautical Communications System (LDACS)
draft-ietf-raw-ldacs-06
Abstract
This document provides an overview of the architecture of the L-band
Digital Aeronautical Communications System (LDACS), which provides a
secure, scalable and spectrum efficient terrestrial data link for
civil aviation. LDACS is a scheduled, reliable multi-application
cellular broadband system with support for IPv6. LDACS SHALL provide
a data link for IP network-based aircraft guidance. High reliability
and availability for IP connectivity over LDACS are therefore
essential.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on 29 July 2021.
Copyright Notice
Copyright (c) 2021 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents (https://trustee.ietf.org/
license-info) in effect on the date of publication of this document.
Please review these documents carefully, as they describe your rights
Maeurer, et al. Expires 29 July 2021 [Page 1]
Internet-Draft LDACS January 2021
and restrictions with respect to this document. Code Components
extracted from this document must include Simplified BSD License text
as described in Section 4.e of the Trust Legal Provisions and are
provided without warranty as described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1. Requirements Language . . . . . . . . . . . . . . . . . . 4
2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 4
3. Motivation and Use Cases . . . . . . . . . . . . . . . . . . 5
3.1. Voice Communications Today . . . . . . . . . . . . . . . 5
3.2. Data Communications Today . . . . . . . . . . . . . . . . 6
4. Provenance and Documents . . . . . . . . . . . . . . . . . . 7
5. Applicability . . . . . . . . . . . . . . . . . . . . . . . . 8
5.1. Advances Beyond the State-of-the-Art . . . . . . . . . . 8
5.1.1. Priorities . . . . . . . . . . . . . . . . . . . . . 8
5.1.2. Security . . . . . . . . . . . . . . . . . . . . . . 8
5.1.3. High Data Rates . . . . . . . . . . . . . . . . . . . 9
5.2. Application . . . . . . . . . . . . . . . . . . . . . . . 9
5.2.1. Air-to-Ground Multilink . . . . . . . . . . . . . . . 9
5.2.2. Air-to-Air Extension for LDACS . . . . . . . . . . . 9
5.2.3. Flight Guidance . . . . . . . . . . . . . . . . . . . 10
5.2.4. Business Communication of Airlines . . . . . . . . . 11
5.2.5. LDACS Navigation . . . . . . . . . . . . . . . . . . 11
6. Requirements to LDACS . . . . . . . . . . . . . . . . . . . . 11
7. Characteristics of LDACS . . . . . . . . . . . . . . . . . . 13
7.1. LDACS Sub-Network . . . . . . . . . . . . . . . . . . . . 13
7.2. Topology . . . . . . . . . . . . . . . . . . . . . . . . 14
7.3. LDACS Physical Layer . . . . . . . . . . . . . . . . . . 14
7.4. LDACS Data Link Layer . . . . . . . . . . . . . . . . . . 15
7.5. LDACS Mobility . . . . . . . . . . . . . . . . . . . . . 15
8. Reliability and Availability . . . . . . . . . . . . . . . . 15
8.1. Layer 2 . . . . . . . . . . . . . . . . . . . . . . . . . 15
8.2. Beyond Layer 2 . . . . . . . . . . . . . . . . . . . . . 18
9. Protocol Stack . . . . . . . . . . . . . . . . . . . . . . . 18
9.1. MAC Entity Services . . . . . . . . . . . . . . . . . . . 19
9.2. DLS Entity Services . . . . . . . . . . . . . . . . . . . 21
9.3. VI Services . . . . . . . . . . . . . . . . . . . . . . . 22
9.4. LME Services . . . . . . . . . . . . . . . . . . . . . . 22
9.5. SNP Services . . . . . . . . . . . . . . . . . . . . . . 22
10. Security Considerations . . . . . . . . . . . . . . . . . . . 22
10.1. Reasons for Wireless Digital Aeronautical
Communications . . . . . . . . . . . . . . . . . . . . . 22
10.2. Requirements for LDACS . . . . . . . . . . . . . . . . . 23
10.3. Security Objectives for LDACS . . . . . . . . . . . . . 24
10.4. Security Functions for LDACS . . . . . . . . . . . . . . 24
10.5. Resulting Security Architectural Details . . . . . . . . 24
Maeurer, et al. Expires 29 July 2021 [Page 2]
Internet-Draft LDACS January 2021
10.5.1. Entities in LDACS Security Model . . . . . . . . . . 25
10.5.2. Matter of LDACS Entity Identification . . . . . . . 25
10.5.3. Matter of LDACS Entity Authentication and Key
Negotiation . . . . . . . . . . . . . . . . . . . . . 25
10.5.4. Matter of LDACS Message-in-transit Confidentiality,
Integrity and Authenticity . . . . . . . . . . . . . 26
10.6. Security Modules for LDACS . . . . . . . . . . . . . . . 26
11. Privacy Considerations . . . . . . . . . . . . . . . . . . . 27
12. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 27
13. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 27
14. Normative References . . . . . . . . . . . . . . . . . . . . 27
15. Informative References . . . . . . . . . . . . . . . . . . . 27
Appendix A. Selected Information from DO-350A . . . . . . . . . 30
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 32
1. Introduction
One of the main pillars of the modern Air Traffic Management (ATM)
system is the existence of a communication infrastructure that
enables efficient aircraft control and safe separation in all phases
of flight. Current systems are technically mature but suffering from
the VHF band's increasing saturation in high-density areas and the
limitations posed by analogue radio communications. Therefore,
aviation globally and the European Union (EU) in particular, strives
for a sustainable modernization of the aeronautical communication
infrastructure.
In the long-term, ATM communication SHALL transition from analogue
VHF voice and VDLM2 communication to more spectrum efficient digital
data communication. The European ATM Master Plan foresees this
transition to be realized for terrestrial communications by the
development (and potential implementation) of the L-band Digital
Aeronautical Communications System (LDACS). LDACS SHALL enable IPv6
based air- ground communication related to the aviation safety and
regularity of flight. The particular challenge is that no additional
spectrum can be made available for terrestrial aeronautical
communication. It was thus necessary to develop co-existence
mechanism/procedures to enable the interference free operation of
LDACS in parallel with other aeronautical services/systems in the
same frequency band.
Since LDACS SHALL be used for aircraft guidance, high reliability and
availability for IP connectivity over LDACS are essential.
Maeurer, et al. Expires 29 July 2021 [Page 3]
Internet-Draft LDACS January 2021
1.1. Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
2. Terminology
The following terms are used in the context of RAW in this document:
A2A Air-to-Air
AeroMACS Aeronautical Mobile Airport Communication System
A2G Air-to-Ground
ACARS Aircraft Communications Addressing and Reporting System
ADS-C Automatic Dependent Surveillance - Contract
AM(R)S Aeronautical Mobile (Route) Service
ANSP Air Traffic Network Service Provider
AOC Aeronautical Operational Control
AS Aircraft Station
ATC Air-Traffic Control
ATM Air-Traffic Management
ATN Aeronautical Telecommunication Network
ATS Air Traffic Service
CCCH Common Control Channel
COTS IP Commercial Off-The-Shelf
CM Context Management
CNS Communication Navigation Surveillance
CPDLC Controller Pilot Data Link Communication
DCCH Dedicated Control Channel
DCH Data Channel
DLL Data Link Layer
DLS Data Link Service
DME Distance Measuring Equipment
DSB-AM Double Side-Band Amplitude Modulation
FCI Future Communication Infrastructure
FL Forward Link
GNSS Global Navigation Satellite System
GS Ground-Station
GSC Ground-Station Controller
G2A Ground-to-Air
HF High Frequency
ICAO International Civil Aviation Organization
IP Internet Protocol
kbit/s kilobit per second
LDACS L-band Digital Aeronautical Communications System
LLC Logical Link Control
LME LDACS Management Entity
MAC Medium Access Layer
Maeurer, et al. Expires 29 July 2021 [Page 4]
Internet-Draft LDACS January 2021
MF Multi Frame
OFDM Orthogonal Frequency-Division Multiplexing
OFDMA Orthogonal Frequency-Division Multiplexing Access
OSI Open Systems Interconnection
PHY Physical Layer
RL Reverse Link
SF Super-Frame
SNP Sub-Network Protocol
TDMA Time-Division Multiplexing-Access
VDLM1 VHF Data Link mode 1
VDLM2 VHF Data Link mode 2
VHF Very High Frequency
VI Voice Interface
3. Motivation and Use Cases
Aircraft are currently connected to Air-Traffic Control (ATC) and
Aeronautical Operational Control (AOC) via voice and data
communications systems through all phases of a flight. Within the
airport terminal, connectivity is focused on high bandwidth
communications, while during en-route high reliability, robustness,
and range is the main focus. Voice communications MAY use the same
or different equipment as data communications systems. In the
following the main differences between voice and data communications
capabilities are summarized. The assumed use cases for LDACS
completes the list of use cases stated in [RAW-USE-CASES] and the
list of reliable and available wireless technologies presented in
[RAW-TECHNOS].
3.1. Voice Communications Today
Voice links are used for Air-to-Ground (A2G) and Air-to-Air (A2A)
communications. The communication equipment is either ground-based
working in the High Frequency (HF) or Very High Frequency (VHF)
frequency band or satellite-based. All VHF and HF voice
communications is operated via open broadcast channels without
authentication, encryption or other protective measures. The use of
well-proven communication procedures via broadcast channels helps to
enhance the safety of communications by taking into account that
other users MAY encounter communication problems and MAY be
supported, if REQUIRED. The main voice communications media is still
the analogue VHF Double Side-Band Amplitude Modulation (DSB-AM)
communications technique, supplemented by HF Single Side-Band
Amplitude Modulation and satellite communications for remote and
oceanic areas. DSB-AM has been in use since 1948, works reliably and
safely, and uses low-cost communication equipment. These are the
main reasons why VHF DSB-AM communications is still in use, and it is
Maeurer, et al. Expires 29 July 2021 [Page 5]
Internet-Draft LDACS January 2021
likely that this technology will remain in service for many more
years. This however results in current operational limitations and
impediments in deploying new Air-Traffic Management (ATM)
applications, such as flight-centric operation with Point-to-Point
communications.
3.2. Data Communications Today
Like for voice, data communications into the cockpit is currently
provided by ground-based equipment operating either on HF or VHF
radio bands or by legacy satellite systems. All these communication
systems are using narrowband radio channels with a data throughput
capacity in order of kilobits per second. While the aircraft is on
ground some additional communications systems are available, like the
Aeronautical Mobile Airport Communication System (AeroMACS) or public
cellular networks, operating in the Airport (APT) domain and able to
deliver broadband communication capability.
The data communication networks used for the transmission of data
relating to the safety and regularity of the flight MUST be strictly
isolated from those providing entertainment services to passengers.
This leads to a situation that the flight crews are supported by
narrowband services during flight while passengers have access to
inflight broadband services. The current HF and VHF data links
cannot provide broadband services now or in the future, due to the
lack of available spectrum. This technical shortcoming is becoming a
limitation to enhanced ATM operations, such as Trajectory-Based
Operations and 4D trajectory negotiations.
Satellite-based communications are currently under investigation and
enhanced capabilities are under development which will be able to
provide inflight broadband services and communications supporting the
safety and regularity of flight. In parallel, the ground-based
broadband data link technology LDACS is being standardized by ICAO
and has recently shown its maturity during flight tests [SCH20191].
The LDACS technology is scalable, secure and spectrum efficient and
provides significant advantages to the users and service providers.
It is expected that both - satellite systems and LDACS - will be
deployed to support the future aeronautical communication needs as
envisaged by the ICAO Global Air Navigation Plan.
Maeurer, et al. Expires 29 July 2021 [Page 6]
Internet-Draft LDACS January 2021
4. Provenance and Documents
The development of LDACS has already made substantial progress in the
Single European Sky ATM Research framework, short SESAR, and is
currently being continued in the follow-up program SESAR2020
[RIH2018]. A key objective of the this activities is to develop,
implement and validate a modern aeronautical data link able to evolve
with aviation needs over long-term. To this end, an LDACS
specification has been produced [GRA2019] and is continuously
updated; transmitter demonstrators were developed to test the
spectrum compatibility of LDACS with legacy systems operating in the
L-band [SAJ2014]; and the overall system performance was analyzed by
computer simulations, indicating that LDACS can fulfil the identified
requirements [GRA2011].
LDACS standardization within the framework of the ICAO started in
December 2016. The ICAO standardization group has produced an
initial Standards and Recommended Practices document [ICA2018]. It
defines the general characteristics of LDACS. The ICAO
standardization group plans to produce an ICAO technical manual - the
ICAO equivalent to a technical standard - within the next years.
Generally, the group is open to input from all sources and develops
LDACS in the open.
Up to now LDACS standardization has been focused on the development
of the physical layer and the data link layer, only recently have
higher layers come into the focus of the LDACS development
activities. There is currently no "IPv6 over LDACS" specification
publicly available; however, SESAR2020 has started the testing of
IPv6-based LDACS testbeds.
The IPv6 architecture for the aeronautical telecommunication network
is called the Future Communications Infrastructure (FCI). FCI SHALL
support quality of service, diversity, and mobility under the
umbrella of the "multi-link concept". This work is conducted by ICAO
Communication Panel working group WG-I.
In addition to standardization activities several industrial LDACS
prototypes have been built. One set of LDACS prototypes has been
evaluated in flight trials confirming the theoretical results
predicting the system performance [GRA2018] [SCH20191].
Maeurer, et al. Expires 29 July 2021 [Page 7]
Internet-Draft LDACS January 2021
5. Applicability
LDACS is a multi-application cellular broadband system capable of
simultaneously providing various kinds of Air Traffic Services
(including ATS-B3) and AOC communications services from deployed
Ground-Stations (GS). The LDACS A2G sub-system physical layer and
data link layer are optimized for data link communications, but the
system also supports digital air-ground voice communications.
LDACS supports communication in all airspaces (airport, terminal
maneuvering area, and en-route), and on the airport surface. The
physical LDACS cell coverage is effectively de-coupled from the
operational coverage REQUIRED for a particular service. This is new
in aeronautical communications. Services requiring wide-area
coverage can be installed at several adjacent LDACS cells. The
handover between the involved LDACS cells is seamless, automatic, and
transparent to the user. Therefore, the LDACS A2G communications
concept enables the aeronautical communication infrastructure to
support future dynamic airspace management concepts.
5.1. Advances Beyond the State-of-the-Art
LDACS offers several capabilities that are not provided in
contemporarily deployed aeronautical communication systems.
5.1.1. Priorities
LDACS is able to manage services priorities, an important feature not
available in some of the current data link deployments. Thus, LDACS
guarantees bandwidth, low latency, and high continuity of service for
safety critical ATS applications while simultaneously accommodating
less safety-critical AOC services.
5.1.2. Security
LDACS is a secure data link with built-in security mechanisms. It
enables secure data communications for ATS and AOC services,
including secured private communications for aircraft operators and
ANSPs (Air Traffic Network Service Providers). This includes
concepts for key and trust management, mutual authenticated key
exchange protocols, key derivation measures, user and control
message-in-transit confidentiality and authenticity protection,
secure logging and availability and robustness measures [MAE20181],
[MAE20191], [MAE20192].
Maeurer, et al. Expires 29 July 2021 [Page 8]
Internet-Draft LDACS January 2021
5.1.3. High Data Rates
The user data rate of LDACS is 315 kbit/s to 1428 kbit/s on the
forward link (FL) for the connection Ground-to-Air (G2A), and 294
kbit/s to 1390 kbit/s on the reverse link (RF) for the connection
A2G, depending on coding and modulation. This is 50 times the amount
terrestrial digital aeronautical communications systems such as VDLM2
provide [SCH20191].
5.2. Application
LDACS SHALL be used by several aeronautical applications ranging from
enhanced communication protocol stacks (multi-homed mobile IPv6
networks in the aircraft and potentially ad-hoc networks between
aircraft) to classical communication applications (sending GBAS
correction data) and integration with other service domains (using
the communication signal for navigation).
5.2.1. Air-to-Ground Multilink
It is expected that LDACS together with upgraded satellite-based
communications systems will be deployed within the FCI and constitute
one of the main components of the multilink concept within the FCI.
Both technologies, LDACS and satellite systems, have their specific
benefits and technical capabilities which complement each other.
Especially, satellite systems are well-suited for large coverage
areas with less dense air traffic, e.g. oceanic regions. LDACS is
well-suited for dense air traffic areas, e.g. continental areas or
hot-spots around airports and terminal airspace. In addition, both
technologies offer comparable data link capacity and, thus, are well-
suited for redundancy, mutual back-up, or load balancing.
Technically the FCI multilink concept SHALL be realized by multi-
homed mobile IPv6 networks in the aircraft. The related protocol
stack is currently under development by ICAO and the Single European
Sky ATM Research framework.
5.2.2. Air-to-Air Extension for LDACS
A potential extension of the multi-link concept is its extension to
ad-hoc networks between aircraft.
Direct A2A communication between aircrafts in terms of ad-hoc data
networks is currently considered a research topic since there is no
immediate operational need for it, although several possible use
cases are discussed (digital voice, wake vortex warnings, and
trajectory negotiation) [BEL2019]. It SHOULD also be noted that
Maeurer, et al. Expires 29 July 2021 [Page 9]
Internet-Draft LDACS January 2021
currently deployed analog VHF voice radios support direct voice
communication between aircraft, making a similar use case for digital
voice plausible.
LDACS direct A2A is currently not part of standardization.
5.2.3. Flight Guidance
The FCI (and therefore LDACS) SHALL be used to host flight guidance.
This is realized using three applications:
1. Context Management (CM): The CM application SHALL manage the
automatic logical connection to the ATC center currently
responsible to guide the aircraft. Currently this is done by the
air crew manually changing VHF voice frequencies according to the
progress of the flight. The CM application automatically sets up
equivalent sessions.
2. Controller Pilot Data Link Communication (CPDLC): The CPDLC
application provides the air crew with the ability to exchange
data messages similar to text messages with the currently
responsible ATC center. The CPDLC application SHALL take over
most of the communication currently performed over VHF voice and
enable new services that do not lend themselves to voice
communication (e.g., trajectory negotiation).
3. Automatic Dependent Surveillance - Contract (ADS-C): ADS-C
reports the position of the aircraft to the currently active ATC
center. Reporting is bound to "contracts", i.e. pre-defined
events related to the progress of the flight (i.e. the
trajectory). ADS-C and CPDLC are the primary applications used to
implement in-flight trajectory management.
CM, CPDLC, and ADS-C are available on legacy datalinks, but not
widely deployed and with limited functionality.
Further ATC applications MAY be ported to use the FCI or LDACS as
well. A notable application is GBAS for secure, automated landings:
The Global Navigation Satellite System (GNSS) based Ground Based
Augmentation System (GBAS) is used to improve the accuracy of GNSS to
allow GNSS based instrument landings. This is realized by sending
GNSS correction data (e.g., compensating ionospheric errors in the
GNSS signal) to the aircraft's GNSS receiver via a separate data
link. Currently the VDB data link is used. VDB is a narrow-band
single-purpose datalink without advanced security only used to
transmit GBAS correction data. This makes VDB a natural candidate
for replacement by LDACS.
Maeurer, et al. Expires 29 July 2021 [Page 10]
Internet-Draft LDACS January 2021
5.2.4. Business Communication of Airlines
In addition to air traffic services AOC services SHALL be transmitted
over LDACS. AOC is a generic term referring to the business
communication of airlines. Regulatory this is considered related to
the safety and regularity of flight and MAY therefore be transmitted
over LDACS.
AOC communication is considered the main business case for LDACS
communication service providers since modern aircraft generate
significant amounts of data (e.g., engine maintenance data).
5.2.5. LDACS Navigation
Beyond communication radio signals can always also be used for
navigation. LDACS takes this into account.
For future aeronautical navigation, ICAO recommends the further
development of GNSS based technologies as primary means for
navigation. However, the drawback of GNSS is its inherent single
point of failure - the satellite. Due to the large separation
between navigational satellites and aircraft, the received power of
GNSS signals on the ground is very low. As a result, GNSS
disruptions might occasionally occur due to unintentional
interference, or intentional jamming. Yet the navigation services
MUST be available with sufficient performance for all phases of
flight. Therefore, during GNSS outages, or blockages, an alternative
solution is needed. This is commonly referred to as Alternative
Positioning, Navigation, and Timing (APNT).
One of such APNT solution consists of integrating the navigation
functionality into LDACS. The ground infrastructure for APNT is
deployed through the implementation of LDACS's GSs and the navigation
capability comes "for free".
LDACS navigation has already been demonstrated in practice in a
flight measurement campaign [SCH20191].
6. Requirements to LDACS
The requirements to LDACS are mostly defined by its application area:
Communication related to safety and regularity of flight.
Maeurer, et al. Expires 29 July 2021 [Page 11]
Internet-Draft LDACS January 2021
A particularity of the current aeronautical communication landscape
is that it is heavily regulated. Aeronautical data links (for
applications related to safety and regularity of flight) MAY only use
spectrum licensed to aviation and data links endorsed by ICAO.
Nation states can change this locally, however, due to the global
scale of the air transportation system adherence to these practices
is to be expected.
Aeronautical data links for the Aeronautical Telecommunication
Network (ATN) are therefore expected to remain in service for
decades. The VDLM2 data link currently used for digital terrestrial
internetworking was developed in the 1990es (the use of the Open
Systems Interconnection (OSI) stack indicates that as well). VDLM2
is expected to be used at least for several decades. In this respect
aeronautical communication (for applications related to safety and
regularity of flight) is more comparable to industrial applications
than to the open Internet.
Internetwork technology is already installed in current aircraft.
Current ATS applications use either the Aircraft Communications
Addressing and Reporting System (ACARS) or the OSI stack. The
objective of the development effort LDACS as part of the FCI is to
replace legacy OSI stack and proprietary ACARS internetwork
technologies with industry standard IP technology. It is anticipated
that the use of Commercial Off-The-Shelf (COTS) IP technology mostly
applies to the ground network. The avionics networks on the aircraft
will likely be heavily modified or proprietary.
AOC applications currently mostly use the same stack (although some
applications, like the graphical weather service MAY use the
commercial passenger network). This creates capacity problems
(resulting in excessive amounts of timeouts) since the underlying
terrestrial data links (VDLM1/2) do not provide sufficient bandwidth.
The use of non-aviation specific data links is considered a security
problem. Ideally the aeronautical IP internetwork and the Internet
SHOULD be completely separated.
The objective of LDACS is to provide a next generation terrestrial
data link designed to support IP and provide much higher bandwidth to
avoid the currently experienced operational problems.
The requirement for LDACS is therefore to provide a terrestrial high-
throughput data link for IP internetworking in the aircraft.
Maeurer, et al. Expires 29 July 2021 [Page 12]
Internet-Draft LDACS January 2021
In order to fulfil the above requirement LDACS needs to be
interoperable with IP (and IP-based services like Voice-over-IP) at
the gateway connecting the LDACS network to other aeronautical ground
networks (the totality of them being the ATN). On the avionics side
in the aircraft aviation specific solutions are to be expected.
In addition to the functional requirements LDACS and its IP stack
need to fulfil the requirements defined in RTCA DO-350A/EUROCAE ED-
228A [DO350A]. This document defines continuity, availability, and
integrity requirements at different scopes for each air traffic
management application (CPDLC, CM, and ADS-C). The scope most
relevant to IP over LDACS is the CSP (Communication Service Provider)
scope.
Continuity, availability, and integrity requirements are defined in
[DO350A] volume 1 Table 5-14, and Table 6-13. Appendix A presents
the REQUIRED information.
In a similar vein, requirements to fault management are defined in
the same tables.
7. Characteristics of LDACS
LDACS will become one of several wireless access networks connecting
aircraft to the ATN implemented by the FCI and possibly ACARS/FANS
networks [FAN2019].
The current LDACS design is focused on the specification of layer 2.
Achieving stringent the continuity, availability, and integrity
requirements defined in [DO350A] will require the specification of
layer 3 and above mechanisms (e.g. reliable crossover at the IP
layer). Fault management mechanisms are similarly undefined. Input
from the working group will be appreciated here.
7.1. LDACS Sub-Network
An LDACS sub-network contains an Access Router (AR), a Ground-Station
Controller (GSC), and several GS, each of them providing one LDACS
radio cell.
User plane interconnection to the ATN is facilitated by the AR
peering with an A2G Router connected to the ATN. It is up to
implementer's choice to keep AR and A2G Router functions separated,
or to merge them.
The internal control plane of an LDACS sub-network is managed by the
GSC. An LDACS sub-network is illustrated in Figure 1.
Maeurer, et al. Expires 29 July 2021 [Page 13]
Internet-Draft LDACS January 2021
wireless user
link plane
A--------------G----------------AR---A2G-----ATN
S..............S | Router
. control . |
. plane . |
. . |
GSC..............|
. |
. |
GS---------------+
Figure 1: LDACS sub-network with two GSs and one AS
7.2. Topology
LDACS operating in A2G mode is a cellular point-to-multipoint system.
The A2G mode assumes a star-topology in each cell where Aircraft
Stations (AS) belonging to aircraft within a certain volume of space
(the LDACS cell) is connected to the controlling GS. The LDACS GS is
a centralized instance that controls LDACS A2G communications within
its cell. The LDACS GS can simultaneously support multiple bi-
directional communications to the ASs under its control. LDACS's GSs
themselves are connected to a GSC controlling the LDACS sub-network.
Prior to utilizing the system an AS has to register with the
controlling GS to establish dedicated logical channels for user and
control data. Control channels have statically allocated resources,
while user channels have dynamically assigned resources according to
the current demand. Logical channels exist only between the GS and
the AS.
The LDACS wireless link protocol stack defines two layers, the
physical layer and the data link layer.
7.3. LDACS Physical Layer
The physical layer provides the means to transfer data over the radio
channel. The LDACS GS supports bi-directional links to multiple
aircraft under its control. The FL direction at the G2A connection
and the RL direction at the A2G connection are separated by Frequency
Division Duplex. FL and RL use a 500 kHz channel each. The GS
transmits a continuous stream of Orthogonal Frequency-Division
Multiplexing (OFDM) symbols on the FL. In the RL different aircraft
are separated in time and frequency using a combination of Orthogonal
Maeurer, et al. Expires 29 July 2021 [Page 14]
Internet-Draft LDACS January 2021
Frequency-Division Multiple-Access (OFDMA) and Time-Division
Multiple-Access (TDMA). Aircraft thus transmit discontinuously on
the RL with radio bursts sent in precisely defined transmission
opportunities allocated by the GS.
7.4. LDACS Data Link Layer
The data-link layer provides the necessary protocols to facilitate
concurrent and reliable data transfer for multiple users. The LDACS
data link layer is organized in two sub-layers: The medium access
sub-layer and the Logical Link Control (LLC) sub-layer. The medium
access sub-layer manages the organization of transmission
opportunities in slots of time and frequency. The LLC sub-layer
provides acknowledged point-to-point logical channels between the
aircraft and the GS using an automatic repeat request protocol.
LDACS supports also unacknowledged point-to-point channels and G2A
broadcast.
7.5. LDACS Mobility
LDACS supports layer 2 handovers to different LDACS channels.
Handovers MAY be initiated by the aircraft (break-before-make) or by
the GS (make-before-break). Make-before-break handovers are only
supported for GSs connected to the same GSC.
External handovers between non-connected LDACS sub-networks or
different aeronautical data links SHALL be handled by the FCI multi-
link concept.
8. Reliability and Availability
8.1. Layer 2
LDACS has been designed with applications related to the safety and
regularity of flight in mind. It has therefore been designed as a
deterministic wireless data link (as far as this is possible).
Based on channel measurements of the L-band channel [SCHN2016] and
respecting the specific nature of the area of application, LDACS was
designed from the PHY layer up with robustness in mind.
In order to maximize the capacity per channel and to optimally use
the available spectrum, LDACS was designed as an OFDM-based Frequency
Division Duplex system, supporting simultaneous transmissions in FL
at the G2A connection and RF at the A2G connection. The legacy
systems already deployed in the L-band limit the bandwidth of both
channels to approximately 500 kHz.
Maeurer, et al. Expires 29 July 2021 [Page 15]
Internet-Draft LDACS January 2021
The LDACS physical layer design includes propagation guard times
sufficient for the operation at a maximum distance of 200 nautical
miles from the GS. In actual deployment, LDACS can be configured for
any range up to this maximum range.
The LDACS FL physical layer is a continuous OFDM transmission. LDACS
RL transmission is based on OFDMA-TDMA bursts, with silence between
such bursts. The RL resources (i.e. bursts) are assigned to
different ASs on demand by the GS.
The LDACS physical layer supports adaptive coding and modulation for
user data. Control data is always encoded with the most robust
coding and modulation (QPSK coding rate 1/2).
LDACS medium access on top of the physical layer uses a static frame
structure to support deterministic timer management. As shown in
Figure 3 and Figure 4, LDACS framing structure is based on Super-
Frames (SF) of 240ms duration corresponding to 2000 OFDM symbols. FL
and RL boundaries are aligned in time (from the GS perspective)
allowing for deterministic sending windows for KEEP ALIVE messages
and control and data channels in general.
LDACS medium access is always under the control of the GS of a radio
cell. Any medium access for the transmission of user data has to be
requested with a resource request message stating the requested
amount of resources and class of service. The GS performs resource
scheduling on the basis of these requests and grants resources with
resource allocation messages. Resource request and allocation
messages are exchanged over dedicated contention-free control
channels.
The purpose of Quality-of-Service in LDACS medium access is to
provide prioritized medium access at the bottleneck (the wireless
link). The signaling of higher layer Quality-of-Service requirements
to LDACS is yet to be defined. A DiffServ-based solution with a
small number of priorities is to be expected.
LDACS has two mechanisms to request resources from the scheduler in
the GS.
Resources can either be requested "on demand" with a given priority.
On the FL, this is done locally in the GS, on the RL a dedicated
contention-free control channel is used called Dedicated Control
Channel (DCCH), which is roughly 83 bit every 60 ms. A resource
allocation is always announced in the control channel of the FL,
short Common Control Channel (CCCH) having variable size. Due to the
spacing of the RL control channels every 60 ms, a medium access delay
in the same order of magnitude is to be expected.
Maeurer, et al. Expires 29 July 2021 [Page 16]
Internet-Draft LDACS January 2021
Resources can also be requested "permanently". The permanent
resource request mechanism supports requesting recurring resources in
given time intervals. A permanent resource request has to be
canceled by the user (or by the GS, which is always in control).
User data transmissions over LDACS are therefore always scheduled by
the GS, while control data uses statically (i.e. at cell entry)
allocated recurring resources (DCCH and CCCH). The current
specification specifies no scheduling algorithm. Scheduling of RL
resources is done in physical Protocol Data Units of 112 bit (or
larger if more aggressive coding and modulation is used). Scheduling
on the FL is done Byte-wise since the FL is transmitted continuously
by the GS.
In addition to having full control over resource scheduling, the GS
can send forced Handover commands for off-loading or RF channel
management, e.g. when the signal quality declines and a more suitable
GS is in the AS reach. With robust resource management of the
capacities of the radio channel, reliability and robustness measures
are therefore also anchored in the LDACS management entity.
In addition, to radio resource management, the LDACS control channels
are also used to send keep-alive messages, when they are not
otherwise used. Since the framing of the control channels is
deterministic, missing keep-alive messages can thus be immediately
detected. This information is made available to the multi-link
protocols for fault management.
The protocol used to communicate faults is not defined in the LDACS
specification. It is assumed that vendors would use industry
standard protocols like the Simple Network Management Protocol or the
Network Configuration Protocol where security permits.
The LDACS data link layer protocol running on top of the medium
access sub-layer uses ARQ to provide reliable data transmission on
layer 2.
It employs selective repeat ARQ with transparent fragmentation and
reassembly to the resource allocation size to achieve low latency and
a low overhead without losing reliability. It ensures correct order
of packet delivery without duplicates. In case of transmission
errors it identifies lost fragments with deterministic timers synced
to the medium access frame structure and initiates retransmission.
Additionally, the priority mechanism of LDACS ensures the timely
delivery of messages with high importance.
Maeurer, et al. Expires 29 July 2021 [Page 17]
Internet-Draft LDACS January 2021
8.2. Beyond Layer 2
LDACS availability can be increased by appropriately deploying LDACS
infrastructure: This means proliferating the number of terrestrial
base stations. However, the scarcity of aeronautical spectrum for
data link communication (in the case of LDACS: tens of MHz in the
L-band) and the long range (in the case of LDACS: up to 400 km) make
this quite hard. The deployment of a larger number of small cells is
certainly possible, suffers, however, also from the scarcity of
spectrum. An additional constraint to take into account, is that
Distance Measuring Equipment (DME) is the primary user of the
aeronautical L-band. That is, any LDACS deployment has to take DME
frequency planning into account, too.
The aeronautical community has therefore decided not to rely on a
single communication system or frequency band. It is envisioned to
have multiple independent data link technologies in the aircraft
(e.g., terrestrial and SatCom) in addition to legacy VHF voice.
However, as of now no reliability and availability mechanisms that
could utilize the multi-link have been specified on Layer 3 and
above.
Below Layer 2 aeronautics usually relies on hardware redundancy. To
protect availability of the LDACS link, an aircraft equipped with
LDACS will have access to two L-band antennae with triple redundant
radio systems as REQUIRED for any safety relevant system by ICAO.
9. Protocol Stack
The protocol stack of LDACS is implemented in the AS, GS, and GSC: It
consists of the Physical Layer (PHY) with five major functional
blocks above it. Four are placed in the Data Link Layer (DLL) of the
AS and GS: (1) Medium Access Layer (MAC), (2) Voice Interface (VI),
(3) Data Link Service (DLS), and (4) LDACS Management Entity (LME).
The last entity resides within the Sub-Network Layer: Sub-Network
Protocol (SNP). The LDACS network is externally connected to voice
units, radio control units, and the ATN Network Layer.
Figure 2 shows the protocol stack of LDACS as implemented in the AS
and GS.
Maeurer, et al. Expires 29 July 2021 [Page 18]
Internet-Draft LDACS January 2021
IPv6 Network Layer
|
|
+------------------+ +----+
| SNP |--| | Sub-Network
| | | | Layer
+------------------+ | |
| | LME|
+------------------+ | |
| DLS | | | Logical Link
| | | | Control Layer
+------------------+ +----+
| |
DCH DCCH/CCCH
| RACH/BCCH
| |
+--------------------------+
| MAC | Medium Access
| | Layer
+--------------------------+
|
+--------------------------+
| PHY | Physical Layer
+--------------------------+
|
|
((*))
FL/RL radio channels
separated by
Frequency Division Duplex
Figure 2: LDACS protocol stack in AS and GS
9.1. MAC Entity Services
The MAC time framing service provides the frame structure necessary
to realize slot-based Time Division Multiplex access on the physical
link. It provides the functions for the synchronization of the MAC
framing structure and the PHY Layer framing. The MAC time framing
provides a dedicated time slot for each logical channel.
The MAC Sub-Layer offers access to the physical channel to its
service users. Channel access is provided through transparent
logical channels. The MAC Sub-Layer maps logical channels onto the
appropriate slots and manages the access to these channels. Logical
channels are used as interface between the MAC and LLC Sub-Layers.
Maeurer, et al. Expires 29 July 2021 [Page 19]
Internet-Draft LDACS January 2021
The LDACS framing structure for FL and RL is based on Super-Frames
(SF) of 240 ms duration. Each SF corresponds to 2000 OFDM symbols.
The FL and RL SF boundaries are aligned in time (from the view of the
GS).
In the FL, an SF contains a Broadcast Frame of duration 6.72 ms (56
OFDM symbols) for the Broadcast Control Channel (BCCH), and four
Multi-Frames (MF), each of duration 58.32 ms (486 OFDM symbols).
In the RL, each SF starts with a Random Access (RA) slot of length
6.72 ms with two opportunities for sending RL random access frames
for the Random Access Channel (RACH), followed by four MFs. These
MFs have the same fixed duration of 58.32 ms as in the FL, but a
different internal structure
Figure 3 and Figure 4 illustrate the LDACS frame structure.
^
| +------+------------+------------+------------+------------+
| FL | BCCH | MF | MF | MF | MF |
F +------+------------+------------+------------+------------+
r <---------------- Super-Frame (SF) - 240ms ---------------->
e
q +------+------------+------------+------------+------------+
u RL | RACH | MF | MF | MF | MF |
e +------+------------+------------+------------+------------+
n <---------------- Super-Frame (SF) - 240ms ---------------->
c
y
|
----------------------------- Time ------------------------------>
|
Figure 3: SF structure for LDACS
Maeurer, et al. Expires 29 July 2021 [Page 20]
Internet-Draft LDACS January 2021
^
| +-------------+------+-------------+
| FL | DCH | CCCH | DCH |
F +-------------+------+-------------+
r <---- Multi-Frame (MF) - 58.32ms -->
e
q +------+---------------------------+
u RL | DCCH | DCH |
e +------+---------------------------+
n <---- Multi-Frame (MF) - 58.32ms -->
c
y
|
-------------------- Time ------------------>
|
Figure 4: MF structure for LDACS
9.2. DLS Entity Services
The DLS provides acknowledged and unacknowledged (including broadcast
and packet mode voice) bi-directional exchange of user data. If user
data is transmitted using the acknowledged DLS, the sending DLS
entity will wait for an acknowledgement from the receiver. If no
acknowledgement is received within a specified time frame, the sender
MAY automatically try to retransmit its data. However, after a
certain number of failed retries, the sender will suspend further
retransmission attempts and inform its client of the failure.
The DLS uses the logical channels provided by the MAC:
1. A GS announces its existence and access parameters in the
Broadcast Channel (BC).
2. The RA channel enables AS to request access to an LDACS cell.
3. In the FL the CCCH is used by the GS to grant access to data
channel resources.
4. The reverse direction is covered by the RL, where ASs need to
request resources before sending. This happens via the DCCH.
5. User data itself is communicated in the Data Channel (DCH) on the
FL and RL.
Maeurer, et al. Expires 29 July 2021 [Page 21]
Internet-Draft LDACS January 2021
9.3. VI Services
The VI provides support for virtual voice circuits. Voice circuits
MAY either be set-up permanently by the GS (e.g., to emulate voice
party line) or MAY be created on demand. The creation and selection
of voice circuits is performed in the LME. The VI provides only the
transmission services.
9.4. LME Services
The mobility management service in the LME provides support for
registration and de-registration (cell entry and cell exit), scanning
RF channels of neighboring cells and handover between cells. In
addition, it manages the addressing of aircraft/ ASs within cells.
It is controlled by the network management service in the GSC.
The resource management service provides link maintenance (power,
frequency and time adjustments), support for adaptive coding and
modulation, and resource allocation.
9.5. SNP Services
The DLS provides functions REQUIRED for the transfer of user plane
data and control plane data over the LDACS sub-network.
The security service provides functions for secure communication over
the LDACS sub-network. Note that the SNP security service applies
cryptographic measures as configured by the GSC.
10. Security Considerations
10.1. Reasons for Wireless Digital Aeronautical Communications
Aviation will require secure exchanges of data and voice messages for
managing the air-traffic flow safely through the airspaces all over
the world. Historically Communication Navigation Surveillance (CNS)
wireless communications technology emerged from military and a threat
landscape where inferior technological and financial capabilities of
adversaries were assumed [STR2016]. The main communication method
for ATC today is still an open analogue voice broadcast within the
aeronautical VHF band. Currently, the information security is purely
procedural based by using well-trained personnel and proven
communications procedures. This communication method has been in
service since 1948. However since the emergence of civil
aeronautical CNS application and today, the world has changed. First
of all civil applications have significant lower spectrum available
than military applications. This means several military defense
mechanisms such as frequency hopping or pilot symbol scrambling and
Maeurer, et al. Expires 29 July 2021 [Page 22]
Internet-Draft LDACS January 2021
thus a defense-in-depth approach starting at the physical layer is
impossible for civil systems. With the rise of cheap Software
Defined Radios, the previously existing financial barrier is almost
gone and open source projects such as GNU radio [GNU2012] allow the
new type of unsophisticated listeners and possible attackers.
Furthermore most CNS technology developed in ICAO relies on open
standards, thus syntax and semantics of wireless digital aeronautical
communications can be common knowledge for attackers. Finally with
increased digitization and automation of civil aviation the human as
control instance is being taken gradually out of the loop.
Autonomous transport drones or single piloted aircraft demonstrate
this trend. However without profound cybersecurity measures such as
authenticity and integrity checks of messages in-transit on the
wireless link or mutual entity authentication, this lack of a control
instance can prove disastrous. Thus future digital communications
waveforms will need additional embedded security features to fulfill
modern information security requirements like authentication and
integrity. However, these security features require sufficient
bandwidth which is beyond the capabilities of a VHF narrowband
communications system. For voice and data communications, sufficient
data throughput capability is needed to support the security
functions while not degrading performance. LDACS is a data link
technology with sufficient bandwidth to incorporate security without
losing too much user throughput.
As digitalization progresses even further with LDACS and automated
procedures such as 4D-Trajectories allowing semi-automated en-route
flying of aircraft, LDACS requires stronger cybersecurity measures.
10.2. Requirements for LDACS
Overall there are several business goals for cybersecurity to protect
in FCI in civil aviation:
1. Safety: The system MUST sufficiently mitigate attacks, which
contribute to safety hazards.
2. Flight regularity: The system MUST sufficiently mitigate attacks,
which contribute to delays, diversions, or cancellations of
flights.
3. Protection of business interests: The system MUST sufficiently
mitigate attacks which result in financial loss, reputation
damage, disclosure of sensitive proprietary information, or
disclosure of personal information.
Maeurer, et al. Expires 29 July 2021 [Page 23]
Internet-Draft LDACS January 2021
To further analyze assets and derive threats and thus protection
scenarios several Threat-and Risk Analysis were performed for LDACS
[MAE20181] , [MAE20191]. These results allowed deriving security
scope and objectives from the requirements and the conducted Threat-
and Risk Analysis.
10.3. Security Objectives for LDACS
Security considerations for LDACS are defined by the official
Standards And Recommended Practices document by ICAO [ICA2018]:
1. LDACS SHALL provide a capability to protect the availability and
continuity of the system.
2. LDACS SHALL provide a capability including cryptographic
mechanisms to protect the integrity of messages in transit.
3. LDACS SHALL provide a capability to ensure the authenticity of
messages in transit.
4. LDACS SHOULD provide a capability for nonrepudiation of origin
for messages in transit.
5. LDACS SHOULD provide a capability to protect the confidentiality
of messages in transit.
6. LDACS SHALL provide an authentication capability.
7. LDACS SHALL provide a capability to authorize the permitted
actions of users of the system and to deny actions that are not
explicitly authorized.
8. If LDACS provides interfaces to multiple domains, LDACS SHALL
provide capability to prevent the propagation of intrusions within
LDACS domains and towards external domains.
10.4. Security Functions for LDACS
These objectives were used to derive several security functions for
LDACS REQUIRED to be integrated in the LDACS cybersecurity
architecture: (1) Identification, (2) Authentication, (3)
Authorization, (4) Confidentiality, (5) System Integrity, (6) Data
Integrity, (7) Robustness, (8) Reliability, (9) Availability, and
(10) Key and Trust Management. Several works investigated possible
measures to implement these security functions [BIL2017], [MAE20181],
[MAE20191]. Having identified security requirements, objectives and
functions it MUST be ensured that they are applicable.
10.5. Resulting Security Architectural Details
The requirements lead to a LDACS security model including different
entities for identification, authentication and authorization
purposes ensuring integrity, authenticity and confidentiality of data
in-transit especially.
Maeurer, et al. Expires 29 July 2021 [Page 24]
Internet-Draft LDACS January 2021
10.5.1. Entities in LDACS Security Model
A simplified LDACS architectural modelrequires the following
entities: Network operators such as the Societe Internationale de
Telecommunications Aeronautiques (SITA) [SIT2020] and ARINC [ARI2020]
are providing access to the (1) Ground IPS network via an (2) A2G
LDACS Router. This router is attached to a closed off LDACS Access
Network (3) which connects via further (4) Access Routers to the
different (5) LDACS Cell Ranges, each controlled by a (6) GSC and
spanning a local LDACS Access Network connecting to the (7) GSs that
serve one LDACS cell. Via the (8) A2G wireless LDACS data link (9)
AS the aircraft is connected to the ground network and via the (10)
aircrafts's VI and (11) aircraft's network interface, aircraft's data
can be sent via the AS back to the GS and the forwarded back via GSC,
LDACS local access network, access routers, LDACS access network, A2G
LDACS router to the ground IPS network.
10.5.2. Matter of LDACS Entity Identification
LDACS needs specific identities for (1) the AS, (2) the GS, (3) the
GSC and (4) the Network Operator. The aircraft itself can be
identified using the ICAO unique address of an aircraft, the call
sign of that aircraft or the recently founded Privacy ICAO Address
(PIA) program [FAA2020]. It is conceivable that the LDACS AS will
use a combination of aircraft identification, radio component
identification such as MAC addresses and even operator features
identification to create a unique AS LDACS identification tag.
Similar to a 4G's eNodeB Serving Network (SN) Identification tag, a
GS could be identified using a similar field. And again similar to
4G's Mobility Management Entities (MME), a GSC could be identified
using similar identification fields within the LDACS network. The
identification of the network operator is again similar to 4G (e.g.,
E-Plus, AT&T, and TELUS), in the way that the aeronautical network
operators are listed (e.g., ARINC [ARI2020] and SITA [SIT2020]).
10.5.3. Matter of LDACS Entity Authentication and Key Negotiation
In order to anchor Trust within the system all LDACS entities
connected to the ground IPS network SHALL be rooted in an LDACS
specific chain-of-trust and PKI solution, quite similar to AeroMACS
approach [CRO2016]. These X.509 certificates [RFC5280] residing at
the entities and incorporated in the LDACS PKI proof the ownership of
their respective public key, include information about the identity
of the owner and the digital signature of the entity that has
verified the certificate's content. First all ground infrastructures
MUST mutually authenticate to each other, negotiate and derive keys
and, thus, secure all ground connections. How this process is
handled in detail is still an ongoing discussion. However,
Maeurer, et al. Expires 29 July 2021 [Page 25]
Internet-Draft LDACS January 2021
established methods to secure user plane by IPSec [RFC4301] and IKEv2
[RFC7296] or the application layer via TLS 1.3 [RFC8446] are
conceivable. The LDACS PKI with their chain-of-trust approach,
digital certificates and public entity keys lay the groundwork for
this step. In a second step the AS with the LDACS radio approaches
an LDACS cell and performs a cell entry with the corresponding GS.
Similar to the LTE cell attachment process [TS33.401], where
authentication happens after basic communication has been enabled
between AS and GS (step 5a in the UE attachment process [TS33.401]),
the next step is mutual authentication and key exchange. Hence, in
step three using the identity based Station-to-Station (STS) protocol
with Diffie-Hellman Key Exchange [MAE2020], AS and GS establish
mutual trust by authenticating each other, exchanging key material
and finally both ending up with derived key material. A key
confirmation is mandatory before the communication channel between
the AS and the GS can be opened for user-data communications.
10.5.4. Matter of LDACS Message-in-transit Confidentiality, Integrity
and Authenticity
The subsequent key material from the previous step can then be used
to protect LDACS Layer 2 communications via applying encryption and
integrity protection measures on the SNP layer of the LDACS protocol
stack. As LDACS transports AOC and ATS data, the integrity of that
data is most important, while confidentiality only needs to be
applied to AOC data to protect business interests [ICA2018]. This
possibility of providing low layered confidentiality and integrity
protection ensures a secure delivery of user data over the air gap.
Furthermore it ensures integrity protection of LDACS control data.
10.6. Security Modules for LDACS
A draft of the cybersecurity architecture of LDACS can be found in
[ICA2018] and [MAE20182] and respective updates in [MAE20191],
[MAE20192], and [MAE2020]. It proposes the use of an own LDACS PKI,
identity management based on aircraft identities and network operator
identities (e.g., SITA and ARINC), public key certificates
incorporated in the PKI based chain-of-trust and stored in the
entities allowing for mutual authentication and key exchange
procedures, key derivation mechanisms for perfect forward secrecy and
user/control plane message-in-transit integrity and confidentiality
protection. This secures data traveling over the airgap between AS
and GS and also between GS and ANSP regardless of the secure or
unsecure nature of application data. Of course application data
itself MUST be additionally secured to achieve end-to-end security
(secure dialogue service), however the LDACS datalinks aims to
provide an additional layer of protection just for this network
segment.
Maeurer, et al. Expires 29 July 2021 [Page 26]
Internet-Draft LDACS January 2021
11. Privacy Considerations
LDACS provides a Quality-of-Service, and the generic considerations
for such mechanisms apply.
12. IANA Considerations
This memo includes no request to IANA.
13. Acknowledgements
Thanks to all contributors to the development of LDACS and ICAO PT-T.
Thanks to Klaus-Peter Hauf, Bart Van Den Einden, and Pierluigi
Fantappie for further input to this draft.
Thanks to SBA Research Vienna for fruitful discussions on
aeronautical communications concerning security incentives for
industry and potential economic spillovers.
14. Normative References
[RFC4301] Kent, S. and K. Seo, "Security Architecture for the
Internet Protocol", RFC 4301, DOI 10.17487/RFC4301,
December 2005, <https://www.rfc-editor.org/info/rfc4301>.
[RFC5280] Cooper, D., Santesson, S., Farrell, S., Boeyen, S.,
Housley, R., and W. Polk, "Internet X.509 Public Key
Infrastructure Certificate and Certificate Revocation List
(CRL) Profile", RFC 5280, DOI 10.17487/RFC5280, May 2008,
<https://www.rfc-editor.org/info/rfc5280>.
[RFC7296] Kaufman, C., Hoffman, P., Nir, Y., Eronen, P., and T.
Kivinen, "Internet Key Exchange Protocol Version 2
(IKEv2)", STD 79, RFC 7296, DOI 10.17487/RFC7296, October
2014, <https://www.rfc-editor.org/info/rfc7296>.
[RFC8446] Rescorla, E., "The Transport Layer Security (TLS) Protocol
Version 1.3", RFC 8446, DOI 10.17487/RFC8446, August 2018,
<https://www.rfc-editor.org/info/rfc8446>.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/info/rfc2119>.
15. Informative References
Maeurer, et al. Expires 29 July 2021 [Page 27]
Internet-Draft LDACS January 2021
[SCHN2016] Schneckenburger, N., Jost, T., Shutin, D., Walter, M.,
Thiasiriphet, T., Schnell, M., and U.C. Fiebig,
"Measurement of the L-band Air-to-Ground Channel for
Positioning Applications", IEEE Transactions on Aerospace
and Electronic Systems, 52(5), pp.2281-229 , 2016.
[MAE20191] Maeurer, N., Graeupl, T., and C. Schmitt, "Evaluation of
the LDACS Cybersecurity Implementation", IEEE 38th Digital
Avionics Systems Conference (DACS), pp. 1-10, San Diego,
CA, USA , 2019.
[MAE20192] Maeurer, N. and C. Schmitt, "Towards Successful
Realization of the LDACS Cybersecurity Architecture: An
Updated Datalink Security Threat- and Risk Analysis", IEEE
Integrated Communications, Navigation and Surveillance
Conference (ICNS), pp. 1-13, Herndon, VA, USA , 2019.
[GRA2019] Graeupl, T., Rihacek, C., and B. Haindl, "LDACS A/G
Specification", SESAR2020 PJ14-02-01 D3.3.030 , 2019.
[FAN2019] Pierattelli, S., Fantappie, P., Tamalet, S., van den
Einden, B., Rihacek, C., and T. Graeupl, "LDACS Deployment
Options and Recommendations", SESAR2020 PJ14-02-01
D3.4.020 , 2019.
[MAE20182] Maeurer, N. and A. Bilzhause, "A Cybersecurity
Architecture for the L-band Digital Aeronautical
Communications System (LDACS)", IEEE 37th Digital Avionics
Systems Conference (DASC), pp. 1-10, London, UK , 2017.
[GRA2011] Graeupl, T. and M. Ehammer, "L-DACS1 Data Link Layer
Evolution of ATN/IPS", 30th IEEE/AIAA Digital Avionics
Systems Conference (DASC), pp. 1-28, Seattle, WA, USA ,
2011.
[GRA2018] Graeupl, T., Schneckenburger, N., Jost, T., Schnell, M.,
Filip, A., Bellido-Manganell, M.A., Mielke, D.M., Maeurer,
N., Kumar, R., Osechas, O., and G. Battista, "L-band
Digital Aeronautical Communications System (LDACS) flight
trials in the national German project MICONAV", Integrated
Communications, Navigation, Surveillance Conference
(ICNS), pp. 1-7, Herndon, VA, USA , 2018.
[SCH20191] Schnell, M., "DLR Tests Digital Communications
Technologies Combined with Additional Navigation Functions
for the First Time", 2019.
Maeurer, et al. Expires 29 July 2021 [Page 28]
Internet-Draft LDACS January 2021
[ICA2018] International Civil Aviation Organization (ICAO), "L-Band
Digital Aeronautical Communication System (LDACS)",
International Standards and Recommended Practices Annex 10
- Aeronautical Telecommunications, Vol. III -
Communication Systems , 2018.
[SAJ2014] Haindl, B., Meser, J., Sajatovic, M., Mueller, S.,
Arthaber, H., Faseth, T., and M. Zaisberger, "LDACS1
Conformance and Compatibility Assessment", IEEE/AIAA 33rd
Digital Avionics Systems Conference (DASC), pp. 1-11,
Colorado Springs, CO, USA , 2014.
[RIH2018] Rihacek, C., Haindl, B., Fantappie, P., Pierattelli, S.,
Graeupl, T., Schnell, M., and N. Fistas, "L-band Digital
Aeronautical Communications System (LDACS) Activities in
SESAR2020", Integrated Communications Navigation and
Surveillance Conference (ICNS), pp. 1-8, Herndon, VA,
USA , 2018.
[BEL2019] Bellido-Manganell, M. A. and M. Schnell, "Towards Modern
Air-to-Air Communications: the LDACS A2A Mode", IEEE/AIAA
38th Digital Avionics Systems Conference (DASC), pp. 1-10,
San Diego, CA, USA , 2019.
[TS33.401] Zhang, D., "3GPP System Architecture Evolution (SAE);
Security architecture", T33.401, 3GPP , 2012.
[CRO2016] Crowe, B., "Proposed AeroMACS PKI Specification is a Model
for Global and National Aeronautical PKI Deployments",
WiMAX Forum at 16th Integrated Communications, Navigation
and Surveillance Conference (ICNS), pp. 1-19, New York,
NY, USA , 2016.
[MAE2020] Maeurer, N., Graeupl, T., and C. Schmitt, "Comparing
Different Diffie-Hellman Key Exchange Flavors for LDACS",
IEEE/AIAA 39th Digital Avionics Systems Conference (DASC),
pp. 1-10, San Antonio, TX, USA , 2020.
[STR2016] Strohmeier, M., Schaefer, M., Pinheiro, R., Lenders, V.,
and I. Martinovic, "On Perception and Reality in Wireless
Air Traffic Communication Security", IEEE Transactions on
Intelligent Transportation Systems, 18(6), pp. 1338-1357,
New York, NY, USA , 2016.
Maeurer, et al. Expires 29 July 2021 [Page 29]
Internet-Draft LDACS January 2021
[BIL2017] Bilzhause, A., Belgacem, B., Mostafa, M., and T. Graeupl,
"Datalink Security in the L-band Digital Aeronautical
Communications System (LDACS) for Air Traffic Management",
IEEE Aerospace and Electronic Systems Magazine, 32(11),
pp. 22-33, New York, NY, USA , 2017.
[MAE20181] Maeurer, N. and A. Bilzhause, "Paving the Way for an IT
Security Architecture for LDACS: A Datalink Security
Threat and Risk Analysis", IEEE Integrated Communications,
Navigation, Surveillance Conference (ICNS), pp. 1-11, New
York, NY, USA , 2018.
[FAA2020] FAA, "Federal Aviation Administration. ADS-B Privacy.",
August 2020,
<https://www.faa.gov/nextgen/equipadsb/privacy/>.
[GNU2012] GNU Radio project, "GNU radio", August 2012,
<http://gnuradio.org>.
[SIT2020] SITA, "Societe Internationale de Telecommunications
Aeronautiques", August 2020, <https://www.sita.aero/>.
[ARI2020] ARINC, "Aeronautical Radio Incorporated", August 2020,
<https://www.aviation-ia.com/>.
[DO350A] RTCA SC-214, "Safety and Performance Standard for Baseline
2 ATS Data Communications (Baseline 2 SPR Standard)", May
2016, <https://standards.globalspec.com/std/10003192/rtca-
do-350-volume-1-2>.
[RAW-TECHNOS]
Thubert, P., Cavalcanti, D., Vilajosana, X., Schmitt, C.,
and J. Farkas, "Reliable and Available Wireless
Technologies", Work in Progress, Internet-Draft, draft-
ietf-raw-technologies-00, 20 October 2020,
<https://tools.ietf.org/html/draft-ietf-raw-technologies-
00>.
[RAW-USE-CASES]
Papadopoulos, G., Thubert, P., Theoleyre, F., and C.
Bernardos, "RAW use cases", Work in Progress, Internet-
Draft, draft-ietf-raw-use-cases-00, 23 October 2020,
<https://tools.ietf.org/html/draft-ietf-raw-use-cases-00>.
Appendix A. Selected Information from DO-350A
This appendix includes the continuity, availability, and integrity
requirements interesting for LDACS defined in [DO350A].
Maeurer, et al. Expires 29 July 2021 [Page 30]
Internet-Draft LDACS January 2021
The following terms are used here:
CPDLC Controller Pilot Data Link Communication
DT Delivery Time (nominal) value for RSP
ET Expiration Time value for RCP
FH Flight Hour
MA Monitoring and Alerting criteria
OT Overdue Delivery Time value for RSP
RCP Required Communication Performance
RSP Required Surveillance Performance
TT Transaction Time (nominal) value for RCP
+========================+=============+=============+
| | ECP 130 | ECP 130 |
+========================+=============+=============+
| Parameter | ET | TT95% |
+------------------------+-------------+-------------+
| Transaction Time (sec) | 130 | 67 |
+------------------------+-------------+-------------+
| Continuity | 0.999 | 0.95 |
+------------------------+-------------+-------------+
| Availability | 0.989 | 0.989 |
+------------------------+-------------+-------------+
| Integrity | 1E-5 per FH | 1E-5 per FH |
+------------------------+-------------+-------------+
Table 1: CPDLC Requirements for ECP
+==============+==========+==============+=========+=========+
| | RCP 240 | RCP 240 | RCP 400 | RCP 400 |
+==============+==========+==============+=========+=========+
| Parameter | ET | TT95% | ET | TT95% |
+--------------+----------+--------------+---------+---------+
| Transaction | 240 | 210 | 400 | 350 |
| Time (sec) | | | | |
+--------------+----------+--------------+---------+---------+
| Continuity | 0.999 | 0.95 | 0.999 | 0.95 |
+--------------+----------+--------------+---------+---------+
| Availability | 0.989 | 0.989 | 0.989 | 0.989 |
| | (safety) | (efficiency) | | |
+--------------+----------+--------------+---------+---------+
| Integrity | 1E-5 per | 1E-5 per FH | 1E-5 | 1E-5 |
| | FH | | per FH | per FH |
+--------------+----------+--------------+---------+---------+
Table 2: CPDLC Requirements for RCP
Maeurer, et al. Expires 29 July 2021 [Page 31]
Internet-Draft LDACS January 2021
RCP Monitoring and Alerting Criteria in case of CPDLC:
- MA-1: The system SHALL be capable of detecting failures and
configuration changes that would cause the communication service
no longer meet the RCP specification for the intended use.
- MA-2: When the communication service can no longer meet the RCP
specification for the intended function, the flight crew and/or
the controller SHALL take appropriate action.
+==============+=====+=====+==========+==============+======+=======+
| | RSP | RSP | RSP 180 | RSP 180 | RSP |RSP 400|
| | 160 | 160 | | | 400 | |
+==============+=====+=====+==========+==============+======+=======+
| Parameter | OT |DT95%| OT | DT95% | OT | DT95% |
+--------------+-----+-----+----------+--------------+------+-------+
| Transaction | 160 | 90 | 180 | 90 | 400 | 300 |
| Time (sec) | | | | | | |
+--------------+-----+-----+----------+--------------+------+-------+
| Continuity |0.999| 0.95| 0.999 | 0.95 |0.999 | 0.95 |
+--------------+-----+-----+----------+--------------+------+-------+
| Availability |0.989|0.989| 0.989 | 0.989 |0.989 | 0.989 |
| | | | (safety) | (efficiency) | | |
+--------------+-----+-----+----------+--------------+------+-------+
| Integrity | 1E-5| 1E-5| 1E-5 per | 1E-5 per FH | 1E-5 | 1E-5 |
| | per | per | FH | |per FH| per FH|
| | FH | FH | | | | |
+--------------+-----+-----+----------+--------------+------+-------+
Table 3: ADS-C Requirements
RCP Monitoring and Alerting Criteria:
- MA-1: The system SHALL be capable of detecting failures and
configuration changes that would cause the ADS-C service no longer
meet the RSP specification for the intended function.
- MA-2: When the ADS-C service can no longer meet the RSP
specification for the intended function, the flight crew and/or
the controller SHALL take appropriate action.
Authors' Addresses
Maeurer, et al. Expires 29 July 2021 [Page 32]
Internet-Draft LDACS January 2021
Nils Maeurer (editor)
German Aerospace Center (DLR)
Muenchner Strasse 20
82234 Wessling
Germany
Email: Nils.Maeurer@dlr.de
Thomas Graeupl (editor)
German Aerospace Center (DLR)
Muenchner Strasse 20
82234 Wessling
Germany
Email: Thomas.Graeupl@dlr.de
Corinna Schmitt (editor)
Research Institute CODE, UniBwM
Werner-Heisenberg-Weg 28
85577 Neubiberg
Germany
Email: corinna.schmitt@unibw.de
Maeurer, et al. Expires 29 July 2021 [Page 33]