Skip to main content

Transmission of Syslog Messages over UDP
draft-ietf-syslog-transport-udp-12

The information below is for an old version of the document that is already published as an RFC.
Document Type
This is an older version of an Internet-Draft that was ultimately published as RFC 5426.
Author Anton Okmianski
Last updated 2015-10-14 (Latest revision 2007-09-05)
RFC stream Internet Engineering Task Force (IETF)
Intended RFC status Proposed Standard
Formats
Reviews
Additional resources Mailing list discussion
Stream WG state (None)
Document shepherd (None)
IESG IESG state Became RFC 5426 (Proposed Standard)
Action Holders
(None)
Consensus boilerplate Unknown
Telechat date (None)
Responsible AD Sam Hartman
Send notices to (None)
draft-ietf-syslog-transport-udp-12
syslog Working Group                                        A. Okmianski
Internet-Draft                                       Cisco Systems, Inc.
Intended status: Standards Track                       September 5, 2007
Expires: March 8, 2008

                Transmission of syslog messages over UDP
                   draft-ietf-syslog-transport-udp-12

Status of this Memo

   By submitting this Internet-Draft, each author represents that any
   applicable patent or other IPR claims of which he or she is aware
   have been or will be disclosed, and any of which he or she becomes
   aware will be disclosed, in accordance with Section 6 of BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF), its areas, and its working groups.  Note that
   other groups may also distribute working documents as Internet-
   Drafts.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   The list of current Internet-Drafts can be accessed at
   http://www.ietf.org/ietf/1id-abstracts.txt.

   The list of Internet-Draft Shadow Directories can be accessed at
   http://www.ietf.org/shadow.html.

   This Internet-Draft will expire on March 8, 2008.

Copyright Notice

   Copyright (C) The IETF Trust (2007).

Abstract

   This document describes the transport for syslog messages over UDP/
   IPv4 or UDP/IPv6.  The syslog protocol layered architecture provides
   for support of any number of transport mappings.  However, for
   interoperability purposes, syslog protocol implementers are required
   to support this transport mapping.

Okmianski                 Expires March 8, 2008                 [Page 1]
Internet-Draft            syslog udp transport            September 2007

Table of Contents

   1.  Introduction . . . . . . . . . . . . . . . . . . . . . . . . .  3
   2.  Conventions Used in This Document  . . . . . . . . . . . . . .  3
   3.  Transport Protocol . . . . . . . . . . . . . . . . . . . . . .  3
     3.1.  One Message Per Datagram . . . . . . . . . . . . . . . . .  3
     3.2.  Message Size . . . . . . . . . . . . . . . . . . . . . . .  3
     3.3.  Source and Target Ports  . . . . . . . . . . . . . . . . .  4
     3.4.  Source IP Address  . . . . . . . . . . . . . . . . . . . .  4
     3.5.  UDP/IP Structure . . . . . . . . . . . . . . . . . . . . .  5
     3.6.  UDP Checksums  . . . . . . . . . . . . . . . . . . . . . .  5
   4.  Reliability Considerations . . . . . . . . . . . . . . . . . .  5
     4.1.  Lost Datagrams . . . . . . . . . . . . . . . . . . . . . .  5
     4.2.  Message Corruption . . . . . . . . . . . . . . . . . . . .  5
     4.3.  Congestion Control . . . . . . . . . . . . . . . . . . . .  5
     4.4.  Sequenced Delivery . . . . . . . . . . . . . . . . . . . .  6
   5.  Security Considerations  . . . . . . . . . . . . . . . . . . .  6
     5.1.  Sender Authentication and Message Forgery  . . . . . . . .  6
     5.2.  Message Observation  . . . . . . . . . . . . . . . . . . .  7
     5.3.  Replaying  . . . . . . . . . . . . . . . . . . . . . . . .  7
     5.4.  Unreliable Delivery  . . . . . . . . . . . . . . . . . . .  7
     5.5.  Message Prioritization and Differentiation . . . . . . . .  8
     5.6.  Denial of Service  . . . . . . . . . . . . . . . . . . . .  8
   6.  IANA Considerations  . . . . . . . . . . . . . . . . . . . . .  8
   7.  Notice to RFC Editor . . . . . . . . . . . . . . . . . . . . .  8
   8.  Acknowledgements . . . . . . . . . . . . . . . . . . . . . . .  8
   9.  References . . . . . . . . . . . . . . . . . . . . . . . . . .  9
     9.1.  Normative References . . . . . . . . . . . . . . . . . . .  9
     9.2.  Informative References . . . . . . . . . . . . . . . . . .  9
   Author's Address . . . . . . . . . . . . . . . . . . . . . . . . .  9
   Intellectual Property and Copyright Statements . . . . . . . . . . 10

Okmianski                 Expires March 8, 2008                 [Page 2]
Internet-Draft            syslog udp transport            September 2007

1.  Introduction

   The informational RFC 3164 [8] describes the syslog protocol as it
   was observed in existing implementations.  It describes both the
   format of syslog messages and a UDP [1] transport.  Subsequently, a
   standards-track syslog protocol has been defined in the RFC-protocol
   [2].

   The RFC-protocol specifies a layered architecture that provides for
   support of any number of transport layer mappings for transmitting
   syslog messages.  This document describes the UDP transport mapping
   for the syslog protocol.

   The transport described in this document can be used for transmitting
   syslog messages over both IPv4 [3] and IPv6 [4].  The IPv4 version of
   this transport mapping is REQUIRED for all syslog protocol
   implementations on devices supporting IPv4.  The IPv6 version of this
   transport mapping is REQUIRED for all syslog protocol implementations
   on IPv6-only devices, and RECOMMENDED for dual-stack devices.  These
   requirements are mandated for interoperability purposes.

   Network administrators and architects should be aware of the
   significant reliability and security issues of this transport, which
   stem from the use of UDP.  They are documented in this specification.
   However, this transport is lightweight and is built upon the existing
   popular use of UDP for syslog.

2.  Conventions Used in This Document

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in RFC 2119 [5].

3.  Transport Protocol

3.1.  One Message Per Datagram

   Each syslog UDP datagram MUST contain only one syslog message, which
   MAY be complete or truncated.  The message MUST be formatted and
   truncated according to the RFC-protocol [2].  Additional data MUST
   NOT be present in the datagram payload.

3.2.  Message Size

   This transport mapping supports transmission of syslog messages up to
   65535 octets minus the UDP header length.  This limit stems from the

Okmianski                 Expires March 8, 2008                 [Page 3]
Internet-Draft            syslog udp transport            September 2007

   maximum supported UDP size of 65535 octets specified in the RFC 768
   [1].  For IPv4, the maximum payload size is 65535 octets minus the
   UDP header and minus the IP header because IPv4 has a 16-bit length
   field that also includes the header length.

   IPv4 syslog receivers MUST be able to receive datagrams with message
   size up to and including 480 octets.  IPv6 syslog receivers MUST be
   able to receive datagrams with message size up to and including 1180
   octets.  All syslog receivers SHOULD be able to receive datagrams
   with messages size of up to 2048 octets.  The ability to receive
   larger messages is encouraged.

   The above restrictions and recommendations establish a baseline for
   interoperability.  The minimum required message size support was
   determined based on the minimum MTU size that Internet hosts are
   required to support: 576 octets for IPv4 [3] and 1280 octets for IPv6
   [4].  Datagrams that conform to these limits have the greatest chance
   of being delivered because they do not require fragmentation.

   It is RECOMMENDED that syslog senders restrict message sizes such
   that IP datagrams do not exceed the smallest MTU of the network in
   use.  This avoids datagram fragmentation and possible issues
   surrounding fragmentation such as incorrect MTU discovery.
   Fragmentation can be undesirable because it increases the risk of the
   message being lost due to loss of just one datagram fragment.  Syslog
   has no acknowledgment facility, and therefore there is no effective
   way to handle retransmission.  This makes it impossible for syslog to
   utilize packetization layer path MTU discovery [9].  When network MTU
   is not known in advance, the safest assumption is to restrict
   messages to 480 octets for IPv4 and 1180 octets for IPv6.

3.3.  Source and Target Ports

   Syslog receivers MUST support accepting syslog datagrams on the well-
   known UDP port 514, but MAY be configurable to listen on a different
   port.  Syslog senders MUST support sending syslog message datagrams
   to the UDP port 514, but MAY be configurable to send messages to a
   different port.  Syslog senders MAY use any source UDP port for
   transmitting messages.

3.4.  Source IP Address

   The source IP address of the UDP datagrams SHOULD NOT be interpreted
   as the identifier for the host that originated the syslog message.
   The entity sending the syslog message could be merely a relay.  The
   syslog message itself contains the identifier of the originator of
   the message.

Okmianski                 Expires March 8, 2008                 [Page 4]
Internet-Draft            syslog udp transport            September 2007

3.5.  UDP/IP Structure

   Each UDP/IP datagram sent by the transport layer MUST completely
   adhere to the structure specified in the UDP RFC 768 [1] and either
   IPv4 RFC 791 [3] or IPv6 RFC 2460 [4] depending on which protocol is
   used.

3.6.  UDP Checksums

   Syslog senders MUST NOT disable UDP checksums.  IPv4 syslog senders
   SHOULD use UDP checksums when sending messages.  Note that RFC 2460
   [4] mandates the use of UDP checksums when sending UDP datagrams over
   IPv6.

   Syslog receivers MUST NOT disable UDP checksum checks.  IPv4 syslog
   receivers SHOULD check UDP checksums and they SHOULD accept a syslog
   message with a zero checksum.  Note that RFC 2460 [4] mandates the
   use of checksums for UDP over IPv6.

4.  Reliability Considerations

   The UDP is an unreliable low-overhead protocol.  This section
   discusses reliability issues inherent in UDP that implementers and
   users should be aware of.

4.1.  Lost Datagrams

   This transport mapping does not provide any mechanism to detect and
   correct loss of datagrams.  Datagrams can be lost in transit due to
   congestion, corruption, or any other intermittent network problem.
   IP fragmentation exacerbates this problem because loss of a single
   fragment will result in the entire message being discarded.

4.2.  Message Corruption

   The UDP/IP datagrams can get corrupted in transit due to software,
   hardware, or network errors.  This transport mapping specifies use of
   UDP checksums to enable corruption detection in addition to checksums
   used in IP and Layer 2 protocols.  However, checksums do not
   guarantee corruption detection, and this transport mapping does not
   provide for message acknowledgement or retransmission mechanism.

4.3.  Congestion Control

   Because syslog can generate unlimited amounts of data, transferring
   this data over UDP is generally problematic, because UDP lacks
   congestion control mechanisms.  Congestion control mechanisms that

Okmianski                 Expires March 8, 2008                 [Page 5]
Internet-Draft            syslog udp transport            September 2007

   respond to congestion by reducing traffic rates and establish a
   degree of fairness between flows that share the same path are vital
   to the stable operation of the Internet [6].  This is why the syslog
   TLS transport [7] is REQUIRED to implement and RECOMMENDED for
   general use.

   The only environments where the syslog UDP transport MAY be used as
   an alternative to the TLS transport are managed networks, where the
   network path has been explicitly provisioned for UDP syslog traffic
   through traffic engineering mechanisms, such as rate limiting or
   capacity reservations.  In all other environments, the TLS transport
   [7] SHOULD be used.

4.4.  Sequenced Delivery

   The IP transport used by the UDP does not guarantee that the sequence
   of datagram delivery will match the order in which the datagrams were
   sent.  The time stamp contained within each syslog message can serve
   as a rough guide in establishing sequence order, but it will not help
   in cases when multiple messages were generated during the same time
   slot, the sender cannot generate a time stamp, or messages originated
   from different hosts whose clocks are not synchronized.  The order of
   syslog message arrival via this transport SHOULD NOT be used as an
   authoritative guide in establishing an absolute or relative sequence
   of events on the syslog sender hosts.

5.  Security Considerations

   Using this specification on an unsecured network is NOT RECOMMENDED.
   Several syslog security considerations are discussed in RFC-protocol
   [2].  This section focuses on security considerations specific to the
   syslog transport over UDP.  Some of the security issues raised in
   this section can be mitigated through the use of IPsec as defined in
   RFC 4301 [10].

5.1.  Sender Authentication and Message Forgery

   This transport mapping does not provide for strong sender
   authentication.  The receiver of the syslog message will not be able
   to ascertain that the message was indeed sent from the reported
   sender, or whether the packet was sent from another device.  This can
   also lead to a case of mistaken identity if an inappropriately
   configured machine sends syslog messages to a receiver representing
   itself as another machine.

   This transport mapping does not provide protection against syslog
   message forgery.  An attacker can transmit syslog messages (either

Okmianski                 Expires March 8, 2008                 [Page 6]
Internet-Draft            syslog udp transport            September 2007

   from the machine from which the messages are purportedly sent or from
   any other machine) to a receiver.

   In one case, an attacker can hide the true nature of an attack amidst
   many other messages.  As an example, an attacker can start generating
   forged messages indicating a problem on some machine.  This can get
   the attention of the system administrators, who will spend their time
   investigating the alleged problem.  During this time, the attacker
   could be able to compromise a different machine or a different
   process on the same machine.

   Additionally, an attacker can generate false syslog messages to give
   untrue indications of the status of systems.  As an example, an
   attacker can stop a critical process on a machine, which could
   generate a notification of exit.  The attacker can subsequently
   generate a forged notification that the process had been restarted.
   The system administrators could accept that misinformation and not
   verify that the process had indeed not been restarted.

5.2.  Message Observation

   This transport mapping does not provide confidentiality of the
   messages in transit.  If syslog messages are in clear text, this is
   how they will be transferred.  In most cases passing clear-text
   human-readable messages is a benefit to the administrators.
   Unfortunately, an attacker could also be able to observe the human-
   readable contents of syslog messages.  The attacker could then use
   the knowledge gained from these messages to compromise a machine.  It
   is RECOMMENDED that no sensitive information be transmitted via this
   transport mapping or that transmission of such information be
   restricted to properly secured networks.

5.3.  Replaying

   Message forgery and observation can be combined into a replay attack.
   An attacker could record a set of messages that indicate normal
   activity of a machine.  At a later time, an attacker could remove
   that machine from the network and replay the syslog messages with new
   time stamps.  The administrators could find nothing unusual in the
   received messages, and their receipt would falsely indicate normal
   activity of the machine.

5.4.  Unreliable Delivery

   As was previously discussed in the Reliability Considerations
   section, the UDP transport is not reliable, and packets containing
   syslog message datagrams can be lost in transit without any notice.
   There can be security consequences to the loss of one or more syslog

Okmianski                 Expires March 8, 2008                 [Page 7]
Internet-Draft            syslog udp transport            September 2007

   messages.  Administrators could be unaware of a developing and
   potentially serious problem.  Messages could also be intercepted and
   discarded by an attacker as a way to hide unauthorized activities.

5.5.  Message Prioritization and Differentiation

   This transport mapping does not mandate prioritization of syslog
   messages on the wire or when processed on the receiving host based on
   their severity.  Unless some prioritization is implemented by sender,
   receiver and/or network, the security implication of such behavior is
   that the syslog receiver or network devices could get overwhelmed
   with low-severity messages and be forced to discard potentially high-
   severity messages.

5.6.  Denial of Service

   An attacker could overwhelm a receiver by sending more messages to it
   than could be handled by the infrastructure or the device itself.
   Implementers SHOULD attempt to provide features that minimize this
   threat such as optionally restricting reception of messages to a set
   of know source IP addresses.

6.  IANA Considerations

   This transport uses UDP port 514 for syslog, as recorded in the IANA
   port-numbers registry.

7.  Notice to RFC Editor

   This is a notice to the RFC editor.  This ID is submitted along with
   ID draft-ietf-syslog-protocol and draft-ietf-syslog-transport-tls.
   The document cross-reference each other.  When RFC numbers are
   determined for each of these IDs, please replace all references to
   "RFC-protocol" and "RFC-transport-tls" in this document with the RFC
   number of draft-ietf-syslog-protocol ID.  Also, please update the
   date, size and URL fields in the section referencing the new RFC.
   Please remove this section after editing.

8.  Acknowledgements

   The author gratefully acknowledges the contributions of: Chris
   Lonvick, Rainer Gerhards, David Harrington, Andrew Ross, Albert
   Mietus, Bernie Volz, Mickael Graham, Greg Morris, Alexandra Fedorova,
   Devin Kowatch, Richard Graveman, and all others who have commented on
   the various versions of this proposal.

Okmianski                 Expires March 8, 2008                 [Page 8]
Internet-Draft            syslog udp transport            September 2007

9.  References

9.1.  Normative References

   [1]   Postel, J., "User Datagram Protocol", STD 6, RFC 768,
         August 1980.

   [2]   Gerhards, R., "The syslog Protocol", RFC RFC-protocol,
         January 2007.

   [3]   Postel, J., "Internet Protocol", STD 5, RFC 791,
         September 1981.

   [4]   Deering, S. and R. Hinden, "Internet Protocol, Version 6 (IPv6)
         Specification", RFC 2460, December 1998.

   [5]   Bradner, S., "Key words for use in RFCs to Indicate Requirement
         Levels", BCP 14, RFC 2119, March 1997.

   [6]   Floyd, S., "Congestion Control Principles", BCP 41, RFC 2914,
         September 2000.

   [7]   Miao, F. and Y. Ma, "TLS Transport Mapping for Syslog",
         RFC RFC-transport-tls, May 2007.

9.2.  Informative References

   [8]   Lonvick, C., "The BSD Syslog Protocol", RFC 3164, August 2001.

   [9]   Mogul, J. and S. Deering, "Path MTU discovery", RFC 1191,
         November 1990.

   [10]  Kent, S. and K. Seo, "Security Architecture for the Internet
         Protocol", RFC 4301, December 2005.

Author's Address

   Anton Okmianski
   Cisco Systems, Inc.
   1414 Massachusetts Ave
   Boxborough, MA  01719-2205
   USA

   Phone: +1-978-936-1612
   Email: aokmians@cisco.com

Okmianski                 Expires March 8, 2008                 [Page 9]
Internet-Draft            syslog udp transport            September 2007

Full Copyright Statement

   Copyright (C) The IETF Trust (2007).

   This document is subject to the rights, licenses and restrictions
   contained in BCP 78, and except as set forth therein, the authors
   retain all their rights.

   This document and the information contained herein are provided on an
   "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
   OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND
   THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS
   OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
   THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
   WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Intellectual Property

   The IETF takes no position regarding the validity or scope of any
   Intellectual Property Rights or other rights that might be claimed to
   pertain to the implementation or use of the technology described in
   this document or the extent to which any license under such rights
   might or might not be available; nor does it represent that it has
   made any independent effort to identify any such rights.  Information
   on the procedures with respect to rights in RFC documents can be
   found in BCP 78 and BCP 79.

   Copies of IPR disclosures made to the IETF Secretariat and any
   assurances of licenses to be made available, or the result of an
   attempt made to obtain a general license or permission for the use of
   such proprietary rights by implementers or users of this
   specification can be obtained from the IETF on-line IPR repository at
   http://www.ietf.org/ipr.

   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights that may cover technology that may be required to implement
   this standard.  Please address the information to the IETF at
   ietf-ipr@ietf.org.

Acknowledgment

   Funding for the RFC Editor function is provided by the IETF
   Administrative Support Activity (IASA).

Okmianski                 Expires March 8, 2008                [Page 10]