Adapting HSMs for Post-Quantum Cryptography
draft-reddy-pquip-pqc-hsm-00
This document is an Internet-Draft (I-D).
Anyone may submit an I-D to the IETF.
This I-D is not endorsed by the IETF and has no formal standing in the
IETF standards process.
The information below is for an old version of the document.
| Document | Type |
This is an older version of an Internet-Draft whose latest revision state is "Replaced".
|
|
|---|---|---|---|
| Authors | Tirumaleswar Reddy.K , Dan Wing , Ben S | ||
| Last updated | 2025-02-27 | ||
| Replaced by | draft-ietf-pquip-pqc-hsm-constrained | ||
| RFC stream | (None) | ||
| Formats | |||
| Stream | Stream state | (No stream defined) | |
| Consensus boilerplate | Unknown | ||
| RFC Editor Note | (None) | ||
| IESG | IESG state | I-D Exists | |
| Telechat date | (None) | ||
| Responsible AD | (None) | ||
| Send notices to | (None) |
draft-reddy-pquip-pqc-hsm-00
PQUIP T. Reddy
Internet-Draft Nokia
Intended status: Informational D. Wing
Expires: 1 September 2025 Cloud Software Group
B. Salter
UK National Cyber Security Centre
28 February 2025
Adapting HSMs for Post-Quantum Cryptography
draft-reddy-pquip-pqc-hsm-00
Abstract
Hardware Security Modules (HSMs) play a critical role in securing
cryptographic operations, including the adoption of Post-Quantum
Cryptography (PQC). This document examines the use of seed-based key
generation in HSMs, which reduces storage requirements but increases
computational overhead for key derivation. It explores trade-offs
between storage efficiency and performance, addressing challenges in
ephemeral key handling and optimization strategies for PQC signature
algorithms. It also discusses PQC impacts to HSM firmware updates
and backup.
About This Document
This note is to be removed before publishing as an RFC.
Status information for this document may be found at
https://datatracker.ietf.org/doc/draft-reddy-pquip-pqc-hsm/.
Discussion of this document takes place on the pquip Working Group
mailing list (mailto:pqc@ietf.org), which is archived at
https://mailarchive.ietf.org/arch/browse/pqc/. Subscribe at
https://www.ietf.org/mailman/listinfo/pqc/.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Reddy, et al. Expires 1 September 2025 [Page 1]
Internet-Draft Adapting HSMs for PQC February 2025
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on 1 September 2025.
Copyright Notice
Copyright (c) 2025 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents (https://trustee.ietf.org/
license-info) in effect on the date of publication of this document.
Please review these documents carefully, as they describe your rights
and restrictions with respect to this document. Code Components
extracted from this document must include Revised BSD License text as
described in Section 4.e of the Trust Legal Provisions and are
provided without warranty as described in the Revised BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Key Management in HSMs for PQC . . . . . . . . . . . . . . . 3
2.1. Seed Management . . . . . . . . . . . . . . . . . . . . . 3
2.1.1. Seed Storage . . . . . . . . . . . . . . . . . . . . 4
2.1.2. Efficient Key Derivation . . . . . . . . . . . . . . 5
2.1.3. Secure Exporting of Seeds . . . . . . . . . . . . . . 6
3. Ephemeral Key Management . . . . . . . . . . . . . . . . . . 6
4. Optimizing Performance in Hardware Implementations of PQC
Signature Algorithms . . . . . . . . . . . . . . . . . . 7
5. Additional Considerations for HSM Use in PQC . . . . . . . . 8
6. Post-quantum Firmware Upgrades for HSMs . . . . . . . . . . . 9
6.1. Post-quantum Firmware Authentication . . . . . . . . . . 9
7. Security Considerations . . . . . . . . . . . . . . . . . . . 10
7.1. Side Channel Protection . . . . . . . . . . . . . . . . . 10
Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . . 10
Informative References . . . . . . . . . . . . . . . . . . . . . 11
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 12
Reddy, et al. Expires 1 September 2025 [Page 2]
Internet-Draft Adapting HSMs for PQC February 2025
1. Introduction
The transition to post-quantum cryptography (PQC) introduces new
challenges for cryptographic key management, particularly within
constrained Hardware Security Modules (HSMs). Unlike high-
performance, rack-mounted HSMs, constrained HSMs operate with limited
memory, storage, and computational resources, making the adoption of
PQC algorithms more challenging. The increased key sizes and
computational demands of PQC require careful consideration to ensure
secure and efficient key management within these constrained
environments.
This document provides industry guidance and best practices for
integrating PQC algorithms into constrained HSMs. It explores key
storage strategies, ephemeral key management, and performance
optimizations specific to resource-limited environments. One
approach to mitigating storage constraints is seed-based key
generation, where only a small seed is stored instead of the full
private key, as supported by PQC schemes like ML-DSA and SLH-DSA.
However, this technique increases computational overhead due to the
need to derive full private keys on demand. The document also
discusses considerations for ephemeral key generation in protocols
like TLS and IPsec, along with techniques to optimize PQC signature
operations to enhance performance within constrained HSMs.
This document focuses on the use of PQC algorithms in HSMs,
specifically the three algorithms finalized by NIST: ML-DSA, ML-KEM,
and SLH-DSA. While other PQC algorithms, such as stateful hash-based
signatures, also provide post-quantum security, they are not covered
in this version of the document. Future revisions may expand the
scope to include additional PQC algorithms.
2. Key Management in HSMs for PQC
One mitigation of storage limitations is to store only the seed
rather than the full expanded private key, as the seed is far smaller
and can derive the expanded private key as necessary.
2.1. Seed Management
The seed generated during the PQC key generation function is highly
sensitive, as it will be used to compute the private key or
decapsulation key. Consequently, seeds must be treated with the same
level of security as private keys.
To comply with [ML-KEM], [ML-DSA], [SLH-DSA] and [REC-KEM]
guidelines:
Reddy, et al. Expires 1 September 2025 [Page 3]
Internet-Draft Adapting HSMs for PQC February 2025
2.1.1. Seed Storage
Seeds must be securely stored within a cryptographic module, such as
a Hardware Security Module (HSM), to ensure protection against
unauthorized access. Since the seed can be used to compute the
private key, it must be safeguarded with the same level of protection
as the private key itself. For example, according to [ML-DSA]
Section 3.6.3, the seed ξ generated during ML-DSA.KeyGen can be
stored for later expansion using ML-DSA.KeyGen_internal.
The choice between storing a seed or an expanded private key involves
trade-offs between storage efficiency and performance. Some
constrained HSMs may store only the seed and derive the expanded
private key on demand, whereas others may prefer storing the full
expanded key to reduce computational overhead during key usage.
While vulnerabilities like the "Unbindable Kemmy Schmidt" attack
[BIND] demonstrate the risks of manipulating expanded private keys in
certain non-HSM environments, these attacks generally assume an
adversary has some level of control over the expanded key format.
However, in a HSM environment, where private keys are typically
protected from such manipulation, the primary motivation for storing
the seed rather than the expanded key is not directly tied to
mitigating "Kemmy" attacks.
The ML-DSA and ML-KEM private key formats, as specified in
[I-D.ietf-lamps-dilithium-certificates] and
[I-D.ietf-lamps-kyber-certificates], represent the private key using
a seed from which the expanded private key is derived. While these
formats rely on the seed for key generation, an HSM may choose to
store the expanded private key to avoid the additional computation
required for running KeyGen. HSM implementations must also consider
compatibility with existing standards such as PKCS#11.
Reddy, et al. Expires 1 September 2025 [Page 4]
Internet-Draft Adapting HSMs for PQC February 2025
This choice between storing the seed or the expanded private key has
direct implications on performance, as key derivation incurs
additional computation. The impact of this overhead varies depending
on the algorithm. For instance, ML-DSA key generation, which
primarily involves polynomial operations using the Number Theoretic
Transform (NTT) and hashing, is computationally efficient. In
contrast, SLH-DSA key generation requires constructing a Merkle tree
and multiple calls to Winternitz One-Time Signature (WOTS+) key
generation, making it significantly slower due to the recursive hash
computations involved. HSM designers must carefully balance storage
efficiency and computational overhead based on system requirements
and operational constraints. While HSMs employ various key storage
strategies, the decision to store full private keys or only seeds
depends on design goals, performance considerations, and standards
compliance.
A key challenge arises when importing an existing private key into a
system designed to store only seeds. When a user attempts to import
an already expanded private key, there is a mismatch between the key
format used internally (seed-based) and the expanded private key.
This issue arises because the internal format is designed for
efficient key storage by deriving the private key from the seed,
while the expanded private key is already fully computed. As NIST
has not defined a single private key format for PQC algorithms, this
creates a potential gap in interoperability.
If the seed is not securely stored at the time of key generation, it
is permanently lost because the process of deriving an expanded key
from the seed relies on a one-way cryptographic function. This one-
way function is designed to ensure that the expanded private key can
be deterministically derived from the seed, but the reverse
operation, deriving the original seed from the expanded key is
computationally infeasible.
2.1.2. Efficient Key Derivation
When storing only the seed in an HSM, it is crucial that the HSM is
capable of deriving the private key efficiently whenever required.
However, it is important to note that constantly re-deriving the
private key for every cryptographic operation may introduce
significant performance overhead. In scenarios where performance is
a critical consideration, it may be more efficient to store the
expanded private key directly instead of only the seed.
The key derivation process, such as ML-KEM.KeyGen_internal for ML-KEM
or similar functions for other PQC algorithms, must still be
implemented in a way that can securely operate within the resource
constraints of the HSM. If using the seed-only model, the derived
Reddy, et al. Expires 1 September 2025 [Page 5]
Internet-Draft Adapting HSMs for PQC February 2025
private key should only be temporarily held in memory during the
cryptographic operation and discarded immediately after use.
However, storing the expanded private key may be a more practical
solution in some scenarios and could be considered for optimization.
2.1.3. Secure Exporting of Seeds
Given the potential for hardware failures or the end-of-life of HSM
devices, it is essential to plan for backup and recovery of the
cryptographic seeds. HSMs should support secure seed backup
mechanisms, ideally leveraging encrypted storage and ensuring that
the backup data is protected from unauthorized access. In a disaster
recovery scenario, the seed should be recoverable to enable the re-
derivation of the private key, provided the proper security measures
are in place to prevent unauthorized extraction. For secure
exporting of seeds, PQC encryption algorithms, such as ML-KEM, should
be used to encrypt the seed before export. This ensures that the
seed remains protected even if the export process is vulnerable to
quantum attacks. The process for secure export should include:
* Encrypting the seed using a post-quantum encryption algorithm,
such as ML-KEM, rather than relying on traditional encryption
algorithms.
* Ensuring the exported seed is accessible only to authorized
entities.
* Enforcing strict access controls and secure transport mechanisms
to prevent unauthorized access during transfer.
Wherever possible, seed generation, storage, and usage should remain
entirely within the cryptographic module. This minimizes the risk of
exposure and ensures compliance with established security guidelines.
3. Ephemeral Key Management
In protocols like TLS and IPsec, ephemeral keys are used for key
exchange. Given the increased size of PQC key material, ephemeral
key management will have to be optimized for both security and
performance.
For PQC KEMs, ephemeral key-pairs must be generated from an ephemeral
seed, which needs to be securely stored temporarily and erased after
use. This approach ensures that ephemeral key generation is
deterministic and minimizes storage overhead in HSMs, as only the
seed (not the full private key) needs to be stored. The ephemeral
seed must be securely erased immediately after the key pair is
generated to prevent potential leakage or misuse.
Reddy, et al. Expires 1 September 2025 [Page 6]
Internet-Draft Adapting HSMs for PQC February 2025
Additionally, ephemeral keys should not be reused across different
algorithm suites and sessions. Each ephemeral key-pair must be
uniquely associated with a specific key exchange instance to prevent
cryptographic vulnerabilities, such as cross-protocol attacks or
unintended key reuse.
HSMs implementing PQC ephemeral key management will have to:
* Generate ephemeral key-pairs on-demand from an ephemeral seed
stored temporarily within the cryptographic module.
* Enforce immediate seed erasure after the key-pair is generated and
the cryptographic operation is completed.
* Prevent key reuse across different algorithm suites or sessions.
4. Optimizing Performance in Hardware Implementations of PQC Signature
Algorithms
When implementing PQC signature algorithms in hardware devices, such
as Hardware Security Modules (HSMs), performance optimization becomes
a critical consideration. Transmitting the entire message to the HSM
for signing can lead to significant overhead, especially for large
payloads. To address this, implementers can leverage techniques that
reduce the data transmitted to the HSM, thereby improving efficiency
and scalability.
One effective approach involves sending only a message digest to the
HSM for signing. By signing the digest of the content rather than
the entire content, the communication between the application and the
HSM is minimized, enabling better performance. This method is
applicable for any PQC signature algorithm, whether it is ML-DSA,
SLH-DSA, or any future signature scheme. For such algorithms, a
mechanism is often provided to pre-hash or process the message in a
way that avoids sending the entire raw message for signing. In
particular, algorithms like SLH-DSA present challenges due to their
construction, which requires multiple passes over the message digest
during the signing process. The signer does not retain the entire
message or its full digest in memory at once. Instead, different
parts of the message digest are processed sequentially during the
signing procedure. This differs from traditional algorithms like RSA
or ECDSA, which allow for more efficient processing of the message,
without requiring multiple passes or intermediate processing of the
digest.
A key consideration when deploying ML-DSA in HSMs is the amount of
RAM available. ML-DSA, unlike traditional signature schemes such as
RSA or ECDSA, requires significant memory during signing due to
Reddy, et al. Expires 1 September 2025 [Page 7]
Internet-Draft Adapting HSMs for PQC February 2025
multiple Number Theoretic Transform (NTT) operations, matrix
expansions, and rejection sampling loops. These steps involve
storing large polynomial vectors and intermediate values, making ML-
DSA more memory-intensive. If an HSM has sufficient RAM, this may
not be an issue. However, in constrained environments with limited
RAM, implementing ML-DSA can be challenging. The signer must store
and process multiple transformed values, leading to increased
computational overhead if the HSM lacks the necessary RAM to manage
these operations efficiently.
To address the memory consumption challenge, algorithms like ML-DSA
offer a form of pre-hash using the mu (message representative) value
described in Section 6.2 of [ML-DSA]. The mu value provides an
abstraction for pre-hashing by allowing the hash or message
representative to be computed outside the HSM. This feature offers
additional flexibility by enabling the use of different cryptographic
modules for the pre-hashing step, reducing RAM consumption within the
HSM. The pre-computed mu value is then supplied to the HSM,
eliminating the need to transmit the entire message for signing.
[I-D.ietf-lamps-dilithium-certificates] discusses leveraging
ExternalMu-ML-DSA, where the pre-hashing step (ExternalMu-ML-
DSA.Prehash) is performed in a software cryptographic module, and
only the pre-hashed message (mu) is sent to the HSM for signing
(ExternalMu-ML-DSA.Sign). By implementing ExternalMu-ML-DSA.Prehash
in software and ExternalMu-ML-DSA.Sign in an HSM, the cryptographic
workload is efficiently distributed, making it practical for high-
volume signing operations even in memory-constrained HSM
environments.
5. Additional Considerations for HSM Use in PQC
Key Rotation and Renewal: Applications are responsible for managing
key lifecycles, including periodic key rotation and renewal, for
compliance and cryptographic agility. While an HSM may provide
mechanisms to facilitate secure key rotation, such as generating new
key pairs, securely storing new seeds, and securely deleting outdated
keys, this functionality is not necessarily specific to PQC.
However, the security of PQC schemes is subject to ongoing research
and potential cryptanalytic advances. Future developments in quantum
algorithms, improved attacks on lattice-based cryptography, or side-
channel vulnerabilities may necessitate adjustments to key sizes,
algorithm choices and key rotation policies. HSMs should be designed
to support flexible key management, including the ability to update
algorithms and parameters as new security recommendations emerge.
Reddy, et al. Expires 1 September 2025 [Page 8]
Internet-Draft Adapting HSMs for PQC February 2025
6. Post-quantum Firmware Upgrades for HSMs
HSMs deployed in the field require periodic firmware upgrades to
patch security vulnerabilities, introduce new cryptographic
algorithms, and improve overall functionality. However, the firmware
upgrade process itself can become a critical attack vector if not
designed to be post-quantum. If an adversary compromises the update
mechanism, they could introduce malicious firmware, undermining all
other security properties of the HSM. Therefore, ensuring a post-
quantum firmware upgrade process is critical for the security of
deployed HSMs.
CRQCs pose an additional risk by breaking traditional digital
signatures (e.g., RSA, ECDSA) used to authenticate firmware updates.
If firmware verification relies on traditional signature algorithms,
attackers could generate forged signatures in the future and
distribute malicious updates.
6.1. Post-quantum Firmware Authentication
To ensure the integrity and authenticity of firmware updates, HSM
vendors will have to adopt PQC digital signature schemes for code
signing. Recommended post-quantum algorithms include:
SLH-DSA (Stateless Hash-Based Digital Signature Algorithm): SLH-DSA
does not introduce any new hardness assumptions beyond those inherent
to its underlying hash functions. It builds upon established
foundations in cryptography, making it a reliable and robust digital
signature scheme for a post-quantum world. While attacks on lattice-
based schemes like ML-DSA can compromise their security, SLH-DSA will
remain unaffected by these attacks due to its distinct mathematical
foundations. This ensures the ongoing security of systems and
protocols that use SLH-DSA for digital signatures. Given that the
first vulnerabilities in PQC algorithms are more likely to arise from
implementation flaws rather than fundamental mathematical weaknesses,
SLH-DSA is still susceptible to attacks if not properly implemented..
HSS-LMS (Hierarchical Signature System - Leighton-Micali Signature):
A hash-based signature scheme, providing long-term security and
efficient key management for firmware authentication (see [REC-SHS]).
XMSS (eXtended Merkle Signature Scheme): Another stateful hash-based
signature scheme similar to HSS-LMS [RFC8391]. XMSS signatures are
slightly shorter than HSS-LMS signatures for equivalent security.
However, HSS-LMS provides performance advantages and HSS-LMS is
considered simpler (see Section 10 of [RFC8554]).
Reddy, et al. Expires 1 September 2025 [Page 9]
Internet-Draft Adapting HSMs for PQC February 2025
Firmware images can be signed using one of these post-quantum
algorithms before being distributed to HSMs. [I-D.wiggers-hbs-state]
discusses various strategies for a correct state and backup
management for stateful hash-based signatures.
Firmware images often have a long lifetime, requiring cryptographic
algorithms that provide strong security assurances over extended
periods. ML-DSA is not included in this list because it is a
lattice-based signature scheme, making it susceptible to potential
advances in quantum and classical attacks on structured lattices.
The long-term security of ML-DSA depends on the continued hardness of
lattice-based problems, which remain an active area of research. In
contrast, SLH-DSA, HSS-LMS, and XMSS are based on well-studied hash
functions, ensuring their security does not rely on unproven
assumptions about lattice hardness. Given this uncertainty, use of a
hash-based signature such as SLH-DSA may be preferable to ML-DSA for
firmware authentication, where cryptographic stability over a long
lifetime is a critical requirement.
7. Security Considerations
The security considerations for key management in HSMs for PQC focus
on the secure storage and handling of cryptographic seeds, which are
used to derive private keys. Seeds must be protected with the same
security measures as private keys, and key derivation should be
efficient and secure within resource-constrained HSMs. Secure export
and backup mechanisms for seeds are essential to ensure recovery in
case of hardware failure, but these processes must be encrypted and
protected from unauthorized access.
7.1. Side Channel Protection
Side-channel attacks exploit physical leaks during cryptographic
operations, such as timing information, power consumption,
electromagnetic emissions, or other physical characteristics, to
extract sensitive data like private keys or seeds. Given the
sensitivity of the seed and private key in PQC key generation, it is
critical to consider side-channel protection in HSM design. While
side-channel attacks remain an active research topic, their
significance in secure hardware design cannot be understated. HSMs
must incorporate strong countermeasures against side-channel
vulnerabilities to prevent attackers from gaining insights into
secret data during cryptographic operations.
Acknowledgements
Thanks to Jean-Pierre Fiset, Richard Kettlewell, Mike Ounsworth, and
Aritra Banerjee for the detailed review.
Reddy, et al. Expires 1 September 2025 [Page 10]
Internet-Draft Adapting HSMs for PQC February 2025
Informative References
[BIND] "Unbindable Kemmy Schmid", n.d.,
<https://eprint.iacr.org/2024/523.pdf>.
[I-D.ietf-lamps-dilithium-certificates]
Massimo, J., Kampanakis, P., Turner, S., and B.
Westerbaan, "Internet X.509 Public Key Infrastructure:
Algorithm Identifiers for ML-DSA", Work in Progress,
Internet-Draft, draft-ietf-lamps-dilithium-certificates-
07, 2 February 2025,
<https://datatracker.ietf.org/doc/html/draft-ietf-lamps-
dilithium-certificates-07>.
[I-D.ietf-lamps-kyber-certificates]
Turner, S., Kampanakis, P., Massimo, J., and B.
Westerbaan, "Internet X.509 Public Key Infrastructure -
Algorithm Identifiers for the Module-Lattice-Based Key-
Encapsulation Mechanism (ML-KEM)", Work in Progress,
Internet-Draft, draft-ietf-lamps-kyber-certificates-08, 2
February 2025, <https://datatracker.ietf.org/doc/html/
draft-ietf-lamps-kyber-certificates-08>.
[I-D.wiggers-hbs-state]
Wiggers, T., Bashiri, K., Kölbl, S., Goodman, J., and S.
Kousidis, "Hash-based Signatures: State and Backup
Management", Work in Progress, Internet-Draft, draft-
wiggers-hbs-state-01, 24 September 2024,
<https://datatracker.ietf.org/doc/html/draft-wiggers-hbs-
state-01>.
[ML-DSA] "FIPS-204: Module-Lattice-Based Digital Signature
Standard", <https://nvlpubs.nist.gov/nistpubs/FIPS/
NIST.FIPS.204.pdf>.
[ML-KEM] "FIPS-203: Module-Lattice-based Key-Encapsulation
Mechanism Standard",
<https://nvlpubs.nist.gov/nistpubs/FIPS/
NIST.FIPS.203.pdf>.
[REC-KEM] "Recommendations for Key-Encapsulation Mechanisms", n.d.,
<https://nvlpubs.nist.gov/nistpubs/SpecialPublications/
NIST.SP.800-227.ipd.pdf>.
[REC-SHS] "Recommendation for Stateful Hash-Based Signature Scheme",
<https://nvlpubs.nist.gov/nistpubs/SpecialPublications/
NIST.SP.800-208.pdf>.
Reddy, et al. Expires 1 September 2025 [Page 11]
Internet-Draft Adapting HSMs for PQC February 2025
[RFC8391] Huelsing, A., Butin, D., Gazdag, S., Rijneveld, J., and A.
Mohaisen, "XMSS: eXtended Merkle Signature Scheme",
RFC 8391, DOI 10.17487/RFC8391, May 2018,
<https://www.rfc-editor.org/rfc/rfc8391>.
[RFC8554] McGrew, D., Curcio, M., and S. Fluhrer, "Leighton-Micali
Hash-Based Signatures", RFC 8554, DOI 10.17487/RFC8554,
April 2019, <https://www.rfc-editor.org/rfc/rfc8554>.
[SLH-DSA] "FIPS-205: Stateless Hash-Based Digital Signature
Standard", <https://nvlpubs.nist.gov/nistpubs/FIPS/
NIST.FIPS.205.pdf>.
Authors' Addresses
Tirumaleswar Reddy
Nokia
Bangalore
Karnataka
India
Email: kondtir@gmail.com
Dan Wing
Cloud Software Group Holdings, Inc.
United States of America
Email: danwing@gmail.com
Ben Salter
UK National Cyber Security Centre
Email: ben.s3@ncsc.gov.uk
Reddy, et al. Expires 1 September 2025 [Page 12]