Skip to main content

YANG Data Model for LSP-Ping
draft-zheng-mpls-lsp-ping-yang-cfg-09

The information below is for an old version of the document.
Document Type
This is an older version of an Internet-Draft whose latest revision state is "Replaced".
Authors Lianshu Zheng , Guangying Zheng , Greg Mirsky , Reshad Rahman , faiqbal@cisco.com
Last updated 2018-10-14
Replaced by draft-nainar-mpls-lsp-ping-yang
RFC stream (None)
Formats
Stream Stream state (No stream defined)
Consensus boilerplate Unknown
RFC Editor Note (None)
IESG IESG state I-D Exists
Telechat date (None)
Responsible AD (None)
Send notices to (None)
draft-zheng-mpls-lsp-ping-yang-cfg-09
Network Working Group                                           L. Zheng
Internet-Draft                                                  G. Zheng
Intended status: Standards Track                     Huawei Technologies
Expires: April 17, 2019                                        G. Mirsky
                                                               ZTE Corp.
                                                               R. Rahman
                                                                F. Iqbal
                                                           Cisco Systems
                                                        October 14, 2018

                      YANG Data Model for LSP-Ping
                 draft-zheng-mpls-lsp-ping-yang-cfg-09

Abstract

   When an LSP fails to deliver user traffic, the failure cannot always
   be detected by the MPLS control plane.  RFC 8029 defines a mechanism
   that would enable users to detect such failure and to isolate faults.
   YANG, defined in RFC 6020 and RFC 7950, is a data modeling language
   used to specify the contents of a conceptual data stores that allows
   networked devices to be managed using NETCONF, as specified in RFC
   6241.  This document defines a YANG data model that can be used to
   configure and manage LSP-Ping.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at https://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on April 17, 2019.

Copyright Notice

   Copyright (c) 2018 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

Zheng, et al.            Expires April 17, 2019                 [Page 1]
Internet-Draft                LSP-Ping YANG                 October 2018

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (https://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   2
     1.1.  Requirements Language . . . . . . . . . . . . . . . . . .   3
     1.2.  Support of Long Running Command with NETCONF  . . . . . .   3
   2.  Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . .   3
   3.  Design of the Data Model  . . . . . . . . . . . . . . . . . .   4
     3.1.  The Configuration of Control Information  . . . . . . . .   4
     3.2.  The Configuration of Schedule Parameters  . . . . . . . .   5
     3.3.  Display of Result Information . . . . . . . . . . . . . .   6
   4.  Data Hierarchy  . . . . . . . . . . . . . . . . . . . . . . .   7
   5.  Interaction with other MPLS OAM Tools Models  . . . . . . . .  10
   6.  LSP-Ping YANG Module  . . . . . . . . . . . . . . . . . . . .  10
   7.  Examples  . . . . . . . . . . . . . . . . . . . . . . . . . .  20
     7.1.  Configuration of Control Information  . . . . . . . . . .  20
     7.2.  The Configuration of Schedule Parameters  . . . . . . . .  21
     7.3.  Display of Result Information . . . . . . . . . . . . . .  22
   8.  Security Considerations . . . . . . . . . . . . . . . . . . .  24
   9.  IANA Considerations . . . . . . . . . . . . . . . . . . . . .  25
   Contributors  . . . . . . . . . . . . . . . . . . . . . . . . . .  25
   Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . . .  25
   12. References  . . . . . . . . . . . . . . . . . . . . . . . . .  25
     12.1.  Normative References . . . . . . . . . . . . . . . . . .  25
     12.2.  Informative References . . . . . . . . . . . . . . . . .  26
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  27

1.  Introduction

   When an LSP fails to deliver user traffic, the failure cannot always
   be detected by the MPLS control plane.  [RFC8029] defines a mechanism
   that would enable users to detect such failure and to isolate faults.
   YANG, defined in [RFC6020] and [RFC7950], is a data modeling language
   that was introduced to define the contents of a conceptual data store
   that allows networked devices to be managed using NETCONF [RFC6241].
   This document defines a YANG data model that can be used to configure
   and manage LSP-Ping [RFC8029].

Zheng, et al.            Expires April 17, 2019                 [Page 2]
Internet-Draft                LSP-Ping YANG                 October 2018

   The rest of this document is organized as follows.  Section 2
   presents the scope of this document.  Section 3 provides the design
   of the LSP-Ping configuration data model in details by containers.
   Section 4 presents the complete data hierarchy of LSP-Ping YANG
   model.  Section 5 discusses the interaction between LSP-Ping data
   model and other MPLS tools data models.  Section 6 specifies the YANG
   module and section 7 lists examples which conform to the YANG module
   specified in this document.  Finally, security considerations are
   discussed in Section 8.

   This version of the interfaces data model conforms to the Network
   Management Datastore Architecture (NMDA) [RFC8342].

1.1.  Requirements Language

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
   "OPTIONAL" in this document are to be interpreted as described in BCP
   14 [RFC2119] [RFC8174] when, and only when, they appear in all
   capitals, as shown here.

1.2.  Support of Long Running Command with NETCONF

   LSP Ping is one of the examples of what can be described as "long-
   running operation".  Unlike most of the configuration operations that
   result in single response execution of an LSP Ping triggers multiple
   responses from a node under control.  The question of implementing
   the long-running operation in NETCONF is still open and possible
   solutions being discussed:

   1.  Consecutive Remote Processing Calls (RPC) to poll for results.

   2.  Model presented in [RFC4560].

   3.  The one outlined in [I-D.mahesh-netconf-persistent].

   The problem of long-running operation as well can be considered as a
   case of controlling and obtaining results from a Measurement Agent
   (MA) as defined in [RFC7594].

2.  Scope

   The fundamental mechanism of LSP-Ping is defined in [RFC8029].
   Extensions of LSP-Ping has been developed over the years.  There are
   extensions for performing LSP ping, for example, over P2MP MPLS LSPs
   [RFC6425] or for Segment Routing IGP Prefix and Adjacency SIDs with
   an MPLS data plane [RFC8287].  These extensions will be considered in
   a later update of this document.

Zheng, et al.            Expires April 17, 2019                 [Page 3]
Internet-Draft                LSP-Ping YANG                 October 2018

3.  Design of the Data Model

   This YANG data model is defined to be used to configure and manage
   LSP-Ping and it provides the following features:

   1.  The configuration of control information of an LSP-Ping test.

   2.  The configuration of schedule parameters of an LSP-Ping test.

   3.  Display of result information of an LSP-Ping test.

   The top-level container lsp-pings holds the configuration of the
   control information, schedule parameters and result information for
   multiple instances of LSP-Ping test.

3.1.  The Configuration of Control Information

   Container lsp-pings:lsp-ping:control-info defines the configuration
   parameters which control an LSP-Ping test.  Examples are the target-
   fec-type/target-fec of the echo request packet and the reply mode of
   the echo reply packet.  Values of some parameters may be auto-
   assigned by the system, but in several cases, there is a requirement
   for configuration of these parameters.  Examples of such parameters
   are source address and outgoing interface.

   The data hierarchy for control information configuration is presented
   below:

Zheng, et al.            Expires April 17, 2019                 [Page 4]
Internet-Draft                LSP-Ping YANG                 October 2018

   module: ietf-lspping
      +--rw lsp-pings
         +--rw lsp-ping* [lsp-ping-name]
            +--rw lsp-ping-name          string
            +--rw control-info
            |  +--rw target-fec-type?       target-fec-type
            |  +--rw (target-fec)?
            |  |  +--:(ip-prefix)
            |  |  |  +--rw ip-address?            inet:ip-address
            |  |  +--:(bgp)
            |  |  |  +--rw bgp?                   inet:ip-address
            |  |  +--:(rsvp)
            |  |  |  +--rw tunnel-interface?      uint32
            |  |  +--:(vpn)
            |  |  |  +--rw vrf-name?              uint32
            |  |  |  +--rw vpn-ip-address?        inet:ip-address
            |  |  +--:(pw)
            |  |  |  +--rw vcid?                  uint32
            |  |  +--:(vpls)
            |  |     +--rw vsi-name?              string
            |  +--rw traffic-class?         uint8
            |  +--rw reply-mode?            reply-mode
            |  +--rw timeout?               uint32
            |  +--rw timeout-units?         units
            |  +--rw interval?              uint32
            |  +--rw interval-units?        units
            |  +--rw probe-count?           uint32
            |  +--rw data-size?             uint32
            |  +--rw data-fill?             string
            |  +--rw description?           string
            |  +--rw source-address-type?   inet:ip-version
            |  +--rw source-address?        inet:ip-address
            |  +--rw ttl?                   uint32
            |  +--rw (outbound)?
            |     +--:(interface)
            |     |  +--rw interface-name?        string
            |     +--:(nexthop)
            |        +--rw nexthop?               inet:ip-address

3.2.  The Configuration of Schedule Parameters

   Container lsp-pings:lsp-ping:schedule-parameters defines the schedule
   parameters of an LSP-Ping test, which describes when to start and
   when to end the test.  Four start modes and three end modes are
   defined respectively.  To be noted that, the configuration of
   "interval" and "probe-count" parameter defined in container lsp-
   pings:lsp-ping:control-info could also determine when the test ends

Zheng, et al.            Expires April 17, 2019                 [Page 5]
Internet-Draft                LSP-Ping YANG                 October 2018

   implicitly.  All these three parameters are optional.If the user does
   not configure either "interval" or "probe-count" parameter, then the
   default values will be used by the system.  If the user configures
   "end-test", then the actual end time of the LSP-Ping test is the
   smaller one between the configuration value of "end-test" and the
   time implicitly determined by the configuration value of
   "interval"/"probe-count".

   The data hierarchy for schedule information configuration is
   presented below:

   module: ietf-lspping
      +--rw lsp-pings
         +--rw lsp-ping* [lsp-ping-name]
            +--rw lsp-ping-name          string
            +--rw control-info
            ...
            +--rw schedule-parameters
            |  +--rw (start-test)?
            |  |  +--:(now)
            |  |  |  +--rw start-test-now?           empty
            |  |  +--:(at)
            |  |  |  +--rw start-test-at?            yang:date-and-time
            |  |  +--:(delay)
            |  |  |  +--rw start-test-delay?         uint32
            |  |  |  +--rw start-test-delay-units?   units
            |  |  +--:(daily)
            |  |     +--rw start-test-daily?         yang:date-and-time
            |  +--rw (end-test)?
            |     +--:(at)
            |     |  +--rw end-test-at?              yang:date-and-time
            |     +--:(delay)
            |     |  +--rw end-test-delay?           uint32
            |     |  +--rw end-test-delay-units?     units
            |     +--:(lifetime)
            |        +--rw end-test-lifetime?        uint32
            |        +--rw lifetime-units?           units

3.3.  Display of Result Information

   Container lsp-pings:lsp-ping:result-info shows the result of the
   current LSP-Ping test.  Both the statistical result e.g. min-rtt, max
   rtt, and per test probe result e.g. return code, return subcode, are
   shown.

   The data hierarchy for display of result information is presented
   below:

Zheng, et al.            Expires April 17, 2019                 [Page 6]
Internet-Draft                LSP-Ping YANG                 October 2018

   module: ietf-lspping
      +--rw lsp-pings
         +--rw lsp-ping* [lsp-ping-name]
            +--rw lsp-ping-name          string
            +--rw control-info
            ...
            +--rw schedule-parameters
            ...
            +--ro result-info
               +--ro operational-status?    operational-status
               +--ro source-address-type?   inet:ip-version
               +--ro source-address?        inet:ip-address
               +--ro target-fec-type?       target-fec-type
               +--ro (target-fec)?
               |  +--:(ip-prefix)
               |  |  +--ro ip-address?            inet:ip-address
               |  +--:(bgp)
               |  |  +--ro bgp?                   inet:ip-address
               |  +--:(rsvp)
               |  |  +--ro tunnel-interface?      uint32
               |  +--:(vpn)
               |  |  +--ro vrf-name?              uint32
               |  |  +--ro vpn-ip-address?        inet:ip-address
               |  +--:(pw)
               |  |  +--ro vcid?                  uint32
               |  +--:(vpls)
               |     +--ro vsi-name?              string
               +--ro min-rtt?               uint32
               +--ro max-rtt?               uint32
               +--ro average-rtt?           uint32
               +--ro probe-responses?       uint32
               +--ro sent-probes?           uint32
               +--ro sum-of-squares?        uint32
               +--ro last-good-probe?       yang:date-and-time
               +--ro probe-results
                  +--ro probe-result* [probe-index]
                     +--ro probe-index        uint32
                     +--ro return-code?       uint8
                     +--ro return-sub-code?   uint8
                     +--ro rtt?               uint32
                     +--ro result-type?       result-type

4.  Data Hierarchy

   The complete data hierarchy of LSP-Ping YANG model is presented
   below.

Zheng, et al.            Expires April 17, 2019                 [Page 7]
Internet-Draft                LSP-Ping YANG                 October 2018

   module: ietf-lspping
      +--rw lsp-pings
         +--rw lsp-ping* [lsp-ping-name]
            +--rw lsp-ping-name          string
            +--rw control-info
            |  +--rw target-fec-type?       target-fec-type
            |  +--rw (target-fec)?
            |  |  +--:(ip-prefix)
            |  |  |  +--rw ip-address?            inet:ip-address
            |  |  +--:(bgp)
            |  |  |  +--rw bgp?                   inet:ip-address
            |  |  +--:(rsvp)
            |  |  |  +--rw tunnel-interface?      uint32
            |  |  +--:(vpn)
            |  |  |  +--rw vrf-name?              uint32
            |  |  |  +--rw vpn-ip-address?        inet:ip-address
            |  |  +--:(pw)
            |  |  |  +--rw vcid?                  uint32
            |  |  +--:(vpls)
            |  |     +--rw vsi-name?              string
            |  +--rw traffic-class?         uint8
            |  +--rw reply-mode?            reply-mode
            |  +--rw timeout?               uint32
            |  +--rw timeout-units?         units
            |  +--rw interval?              uint32
            |  +--rw interval-units?        units
            |  +--rw probe-count?           uint32
            |  +--rw data-size?             uint32
            |  +--rw data-fill?             string
            |  +--rw description?           string
            |  +--rw source-address-type?   inet:ip-version
            |  +--rw source-address?        inet:ip-address
            |  +--rw ttl?                   uint32
            |  +--rw (outbound)?
            |     +--:(interface)
            |     |  +--rw interface-name?        string
            |     +--:(nexthop)
            |        +--rw nexthop?               inet:ip-address
            +--rw schedule-parameters
            |  +--rw (start-test)?
            |  |  +--:(now)
            |  |  |  +--rw start-test-now?           empty
            |  |  +--:(at)
            |  |  |  +--rw start-test-at?            yang:date-and-time
            |  |  +--:(delay)
            |  |  |  +--rw start-test-delay?         uint32
            |  |  |  +--rw start-test-delay-units?   units
            |  |  +--:(daily)

Zheng, et al.            Expires April 17, 2019                 [Page 8]
Internet-Draft                LSP-Ping YANG                 October 2018

            |  |     +--rw start-test-daily?         yang:date-and-time
            |  +--rw (end-test)?
            |     +--:(at)
            |     |  +--rw end-test-at?              yang:date-and-time
            |     +--:(delay)
            |     |  +--rw end-test-delay?           uint32
            |     |  +--rw end-test-delay-units?     units
            |     +--:(lifetime)
            |        +--rw end-test-lifetime?        uint32
            |        +--rw lifetime-units?           units
            +--ro result-info
               +--ro operational-status?    operational-status
               +--ro source-address-type?   inet:ip-version
               +--ro source-address?        inet:ip-address
               +--ro target-fec-type?       target-fec-type
               +--ro (target-fec)?
               |  +--:(ip-prefix)
               |  |  +--ro ip-address?            inet:ip-address
               |  +--:(bgp)
               |  |  +--ro bgp?                   inet:ip-address
               |  +--:(rsvp)
               |  |  +--ro tunnel-interface?      uint32
               |  +--:(vpn)
               |  |  +--ro vrf-name?              uint32
               |  |  +--ro vpn-ip-address?        inet:ip-address
               |  +--:(pw)
               |  |  +--ro vcid?                  uint32
               |  +--:(vpls)
               |     +--ro vsi-name?              string
               +--ro min-rtt?               uint32
               +--ro max-rtt?               uint32
               +--ro average-rtt?           uint32
               +--ro probe-responses?       uint32
               +--ro sent-probes?           uint32
               +--ro sum-of-squares?        uint32
               +--ro last-good-probe?       yang:date-and-time
               +--ro probe-results
                  +--ro probe-result* [probe-index]
                     +--ro probe-index        uint32
                     +--ro return-code?       uint8
                     +--ro return-sub-code?   uint8
                     +--ro rtt?               uint32
                     +--ro result-type?       result-type

Zheng, et al.            Expires April 17, 2019                 [Page 9]
Internet-Draft                LSP-Ping YANG                 October 2018

5.  Interaction with other MPLS OAM Tools Models

   TBA

6.  LSP-Ping YANG Module

<CODE BEGINS> file "ietf-lspping@2018-03-01.yang"
module ietf-lspping {
  namespace "urn:ietf:params:xml:ns:yang:ietf-lspping";
  //namespace need to be assigned by IANA
  prefix "lspping";

  import ietf-inet-types {
  prefix inet;
  }
  import ietf-yang-types{
  prefix yang;
  }

  organization "IETF Multiprotocol Label Switching Working Group";
  contact "draft-zheng-mpls-lsp-ping-yang-cfg";
  description "MPLS LSP-Ping YANG Module";
  revision "2018-03-01" {
    description "07 version, refine the target fec type,
             as per RFC8029 and update Security Considerations section";
    reference "draft-zheng-mpls-lsp-ping-yang-cfg";
  }

  typedef target-fec-type {
    type enumeration {
      enum ip-prefix {
        value "0";
        description "IPv4/IPv6 prefix";
      }
      enum bgp {
        value "1";
        description "BGP IPv4/IPv6 prefix";
      }
      enum rsvp {
        value "2";
        description "Tunnel interface";
      }
      enum vpn {
        value "3";
        description "VPN IPv4/IPv6 prefix";
      }
      enum pw {
        value "4";

Zheng, et al.            Expires April 17, 2019                [Page 10]
Internet-Draft                LSP-Ping YANG                 October 2018

        description "FEC 128 pseudowire IPv4/IPv6";
      }
      enum vpls {
        value "5";
        description "FEC 129 pseudowire IPv4/IPv6";
      }
    }
    description "Target FEC type.";
  }

  typedef reply-mode {
    type enumeration {
      enum do-not-reply {
        value "1";
        description "Do not reply";
      }
      enum reply-via-udp {
        value "2";
        description "Reply via an IPv4/IPv6 UDP packet";
      }
      enum reply-via-udp-router-alert {
        value "3";
        description "Reply via an IPv4/IPv6 UDP packet with
        Router Alert";
      }
      enum reply-via-control-channel {
        value "4";
        description "Reply via application level control
        channel";
      }
    }
    description "Reply mode.";
  }

  typedef units  {
    type enumeration {
      enum seconds {
        description "Seconds";
      }
      enum milliseconds {
        description "Milliseconds";
      }
      enum microseconds {
        description "Microseconds";
      }
      enum nanoseconds {
        description "Nanoseconds";
      }

Zheng, et al.            Expires April 17, 2019                [Page 11]
Internet-Draft                LSP-Ping YANG                 October 2018

    }
    description "Time units";
  }

  typedef operational-status {
    type enumeration {
      enum enabled {
        value "1";
        description "The Test is active.";
      }
      enum disabled {
        value "2";
        description "The test has stopped.";
      }
      enum completed {
        value "3";
        description "The test is completed.";
      }
    }
    description "Operational state of a LSP Ping test.";
  }

  typedef result-type {
    type enumeration {
      enum success {
        value "1";
        description "The test probe is successful.";
      }
      enum fail {
        value "2";
        description "The test probe has failed.";
      }
      enum timeout {
        value "3";
        description "The test probe is timeout.";
      }
    }
    description "Result of each LSP Ping test probe.";
  }

  container lsp-pings {
    description "Multi-instance of LSP Ping test.";
    list lsp-ping {
      key "lsp-ping-name";
      description "LSP Ping test";
      leaf lsp-ping-name {
        type string {
            length "1..31";

Zheng, et al.            Expires April 17, 2019                [Page 12]
Internet-Draft                LSP-Ping YANG                 October 2018

        }
        mandatory "true";
        description "LSP Ping test name.";
      }
      container control-info {
        description "Control information of the LSP Ping test.";
        leaf target-fec-type {
          type target-fec-type;
          description "Specifies the address type of Target FEC.";
        }
        choice target-fec {
          case ip-prefix {
            leaf ip-address {
              type inet:ip-address;
              description "IPv4/IPv6 Prefix.";
            }
          }
          case bgp {
            leaf bgp {
              type inet:ip-address;
              description "BGP IPv4/IPv6 Prefix.";
            }
          }
          case rsvp {
            leaf tunnel-interface {
              type union {
                type uint32;

                type string;
              }
              description "Tunnel interface";
            }
          }
          case vpn {
            leaf vrf-name {
              type uint32;
              description "Layer3 VPN Name.";
            }
            leaf vpn-ip-address {
              type inet:ip-address;
              description "Layer3 VPN IPv4 Prefix.";
            }
          }
          case pw {
            leaf vcid {
              type uint32;
              description "VC ID";
            }

Zheng, et al.            Expires April 17, 2019                [Page 13]
Internet-Draft                LSP-Ping YANG                 October 2018

          }
          case vpls {
            leaf vsi-name {
              type string;
              description "VPLS VSI";
            }
          }
          description "Specifies the address of Target FEC";
        }
        leaf traffic-class {
          type uint8;
          description "Specifies the Traffic Class.";
        }
        leaf reply-mode {
          type reply-mode;
          description "Specifies the reply mode.";
        }
        leaf timeout {
          type uint32;
          description "Specifies the time-out value for a
          LSP Ping operation.";
        }
        leaf timeout-units {
          type units;
          description "Time-out units.";
        }
        leaf interval {
          type uint32;
          default 1;
          description "Specifies the interval to send an LSP Ping
          echo request packet(probe) as part of one LSP Ping test.";
        }
        leaf interval-units {
          type units;
          default seconds;
          description "Interval units.";
        }
        leaf probe-count {
          type uint32;
          default 5;
          description "Specifies the number of probe sent of one
          LSP Ping test.";
        }
        leaf data-size {
          type uint32;
          description "Specifies the size of the data portion to
          be transmitted in a LSP Ping operation, in octets.";
        }

Zheng, et al.            Expires April 17, 2019                [Page 14]
Internet-Draft                LSP-Ping YANG                 October 2018

        leaf data-fill {
          type string{
              length "0..1564";
          }
          description "Used together with the corresponding
          data-size value to determine how to fill the data
          portion of a probe packet.";
        }
        leaf description {
          type string{
              length "1..31";
          }
          description "A descriptive name of the LSP Ping test.";
        }
        leaf source-address-type {
          type inet:ip-version;
          description "Specifies the type of the source address.";
        }
        leaf source-address {
          type inet:ip-address;
          description "Specifies the source address.";
        }
        leaf ttl {
          type uint32;
          default 255;
          description "Time to live.";
        }
        choice outbound {
          case interface {
            leaf interface-name{
              type string{
                length "1..255";
              }
              description "Specifies the outgoing interface.";
            }
          }
          case nexthop{
            leaf nexthop {
              type inet:ip-address;
              description "Specifies the nexthop.";
            }
          }
          description "Specifies the out interface or nexthop";
        }
      }

      container schedule-parameters {
        description "LSP Ping test schedule parameter";

Zheng, et al.            Expires April 17, 2019                [Page 15]
Internet-Draft                LSP-Ping YANG                 October 2018

        choice start-test{
          case now {
            leaf start-test-now {
              type empty;
              description "Start test now.";
            }
          }
          case at {
            leaf start-test-at {
              type yang:date-and-time;
              description "Start test at a specific time.";
            }
          }
          case delay {
            leaf start-test-delay {
              type uint32;
              description "Start after a specific delay.";
            }
            leaf start-test-delay-units {
              type units;
              default seconds;
              description "Delay units.";
            }
          }
          case daily {
            leaf start-test-daily {
              type yang:date-and-time;
              description "Start test daily.";
            }
          }
          description "Specifies when the test begins to start,
          include 4 schedule method: start now(1), start at(2),
          start delay(3), start daily(4).";
        }

        choice end-test{
          case at {
            leaf end-test-at{
              type yang:date-and-time;
              description "End test at a specific time.";
            }
          }
          case delay {
            leaf end-test-delay {
              type uint32;
              description "End after a specific delay.";
            }
            leaf end-test-delay-units {

Zheng, et al.            Expires April 17, 2019                [Page 16]
Internet-Draft                LSP-Ping YANG                 October 2018

              type units;
              default seconds;
              description "Delay units.";
            }
          }
          case lifetime {
            leaf end-test-lifetime {
              type uint32;
              description "Set the test lifetime.";
            }
            leaf lifetime-units {
              type units;
              default seconds;
              description "Lifetime units.";
            }
          }
          description "Specifies when the test ends, include 3
          schedule method: end at(1), end delay(2),
          end lifetime(3).";
        }
      }

      container result-info {
        config "false";
        description "LSP Ping test result information.";
        leaf operational-status {
          type operational-status;
          description "Operational state of a LSP Ping test";
        }
        leaf source-address-type {
          type inet:ip-version;
          description "The source address type.";
        }
        leaf source-address {
          type inet:ip-address;
          description "The source address of the test.";
        }
        leaf target-fec-type {
          type target-fec-type;
          description "The Target FEC address type.";
        }
        choice target-fec {
          case ip-prefix {
            leaf ip-address {
              type inet:ip-address;
              description "IPv4/IPv6 Prefix.";
            }
          }

Zheng, et al.            Expires April 17, 2019                [Page 17]
Internet-Draft                LSP-Ping YANG                 October 2018

          case bgp {
            leaf bgp {
              type inet:ip-address;
              description "BGP IPv4/IPv6 Prefix.";
            }
          }
          case rsvp {
            leaf tunnel-interface {
              type uint32;
              description "Tunnel interface";
            }
          }
          case vpn {
            leaf vrf-name {
              type uint32;
              description "Layer3 VPN Name.";
            }
            leaf vpn-ip-address {
              type inet:ip-address;
              description "Layer3 VPN IPv4 Prefix.";
            }
          }
          case pw {
            leaf vcid {
              type uint32;
              description "VC ID";
            }
          }
          case vpls {
            leaf vsi-name {
              type string;
              description "VPLS VSI";
            }
          }
          description "The Target FEC address";
        }
        leaf min-rtt {
          type uint32;
          description "The minimum LSP Ping round-trip-time (RTT)
          received.";
        }
        leaf max-rtt {
          type uint32;
          description "The maximum LSP Ping round-trip-time (RTT)
          received.";
        }
        leaf average-rtt {
          type uint32;

Zheng, et al.            Expires April 17, 2019                [Page 18]
Internet-Draft                LSP-Ping YANG                 October 2018

          description "The current average LSP Ping round-trip-time
          (RTT).";
        }
        leaf probe-responses {
          type uint32;
          description "Number of responses received for the
          corresponding LSP Ping test.";
        }
        leaf sent-probes {
          type uint32;
          description "Number of probes sent for the
          corresponding LSP Ping test.";
        }
        leaf sum-of-squares {
          type uint32;
          description "The sum of the squares for all
          replies received.";
        }
        leaf last-good-probe {
          type yang:date-and-time;
          description "Date and time when the last response
          was received for a probe.";
        }

        container probe-results {
          description "Result info of test probes.";
          list probe-result {
            key "probe-index";
            description "Result info of each test probe.";
            leaf probe-index {
              type uint32;
              config false;
              description "Probe index";
            }
            leaf return-code {
              type uint8;
              config false;
              description "The Return Code set in the echo reply.";
            }
            leaf return-sub-code {
               type uint8;
               config false;
               description "The Return Sub-code set in the
               echo reply.";
            }
            leaf rtt {
              type uint32;
              config false;

Zheng, et al.            Expires April 17, 2019                [Page 19]
Internet-Draft                LSP-Ping YANG                 October 2018

              description "The round-trip-time (RTT) received.";
            }
            leaf result-type {
              type result-type;
              config false;
              description "The probe result type.";
            }
          }
        }
      }
    }
  }
}
<CODE ENDS>

7.  Examples

   The following examples show the netconf RPC communication between
   client and server for one LSP-Ping test case.

7.1.  Configuration of Control Information

   Configure the control-info for sample-test-case.

Zheng, et al.            Expires April 17, 2019                [Page 20]
Internet-Draft                LSP-Ping YANG                 October 2018

   Request from netconf client:
   <rpc
     message-id="101" xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
     <edit-config>
       <target>
         <running/>
       </target>
       <config>
         <lsp-pings xmlns="urn:ietf:params:xml:ns:yang:ietf-lspping">
           <lsp-ping>
             <lsp-ping-name>sample-test-case</lsp-ping-name>
             <control-info>
               <target-fec-type>ip-prefix</target-fec-type>
               <ip-prefix>2001:db8::1:100/64</ip-prefix>
               <reply-mode>reply-via-udp</reply-mode>
               <timeout>1</timeout>
               <timeout-units>seconds</timeout-units>
               <interval>1</interval>
               <interval-units>seconds</interval-units>
               <probe-count>6</probe-count>
               <admin-status>enabled</admin-status>
               <data-size>64</data-size>
               <data-fill>this is a lsp ping test</data-fill>
               <source-address-type>ipv4</source-address-type>
               <source-address>2001:db8::4</source-address>
               <ttl>56</ttl>
             </control-info>
           </lsp-ping>
         </lsp-pings>
       </config>
     </edit-config>
   </rpc>

   Reply from netconf server:
   <rpc-reply
     message-id="101" xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
     <ok/>
   </rpc-reply>

7.2.  The Configuration of Schedule Parameters

   Set the schedule-parameters for sample-test-case to start the test.

Zheng, et al.            Expires April 17, 2019                [Page 21]
Internet-Draft                LSP-Ping YANG                 October 2018

   Request from netconf client:
   <rpc
     message-id="102" xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
     <edit-config>
       <target>
         <running/>
       </target>
       <config>
         <lsp-pings xmlns="urn:ietf:params:xml:ns:yang:ietf-lspping">
           <lsp-ping>
             <lsp-ping-name>sample-test-case</lsp-ping-name>
             <schedule-parameters>
               <start-test-now/>
             </schedule-parameters>
           </lsp-ping>
         </lsp-pings>
       </config>
     </edit-config>
   </rpc>

   Reply from netconf server:
   <rpc-reply
     message-id="102" xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
     <ok/>
   </rpc-reply>

7.3.  Display of Result Information

   Get the result-info of sample-test-case.

   Request from netconf client:
   <rpc
     message-id="103" xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
     <get>
       <filter type="subtree">
         <lsp-pings xmlns="urn:ietf:params:xml:ns:yang:ietf-lspping">
          <lsp-ping>
            <lsp-ping-name>sample-test-case</lsp-ping-name>
              <result-info/>
          </lsp-ping>
         </lsp-pings>
       </filter>
       </get>
   </rpc>

   Reply from netconf server:
   <rpc-reply
     message-id="103" xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">

Zheng, et al.            Expires April 17, 2019                [Page 22]
Internet-Draft                LSP-Ping YANG                 October 2018

     <data>
       <lsp-pings xmlns="urn:ietf:params:xml:ns:yang:ietf-lspping">
         <lsp-ping>
           <lsp-ping-name>sample-test-case</lsp-ping-name>
           <result-info>
             <operational-status>completed</operational-status>
             <source-address-type>ipv4</source-address-type>
             <source-address>2001:db8::4</source-address>
             <target-fec-type>ip-prefix</target-fec-type>
             <ip-prefix>2001:db8::1:100/64</ip-prefix>
             <min-rtt>10</min-rtt>
             <max-rtt>56</max-rtt>
             <average-rtt>36</average-rtt>
             <probe-responses>6</probe-responses>
             <sent-probes>6</sent-probes>
             <sum-of-squares>8882</sum-of-squares>
             <last-good-probe>2015-07-01T10:36:56<last-good-probe>
             <probe-results>
               <probe-result>
                 <probe-index>0</probe-index>
                 <return-code>0</return-code>
                 <return-sub-code>3</return-sub-code>
                 <rtt>10</rtt>
                 <result-type>success</result-type>
               </probe-result>
               <probe-result>
                 <probe-index>1</probe-index>
                 <return-code>0</return-code>
                 <return-sub-code>3</return-sub-code>
                 <rtt>56</rtt>
                 <result-type>success</result-type>
               </probe-result>
               <probe-result>
                 <probe-index>2</probe-index>
                 <return-code>0</return-code>
                 <return-sub-code>3</return-sub-code>
                 <rtt>35</rtt>
                 <result-type>success</result-type>
               </probe-result>
               <probe-result>
                 <probe-index>3</probe-index>
                 <return-code>0</return-code>
                 <return-sub-code>3</return-sub-code>
                 <rtt>38</rtt>
                 <result-type>success</result-type>
               </probe-result>
               <probe-result>
                 <probe-index>4</probe-index>

Zheng, et al.            Expires April 17, 2019                [Page 23]
Internet-Draft                LSP-Ping YANG                 October 2018

                 <return-code>0</return-code>
                 <return-sub-code>3</return-sub-code>
                 <rtt>36</rtt>
                 <result-type>success</result-type>
               </probe-result>
               <probe-result>
                 <probe-index>5</probe-index>
                 <return-code>0</return-code>
                 <return-sub-code>3</return-sub-code>
                 <rtt>41</rtt>
                 <result-type>success</result-type>
               </probe-result>
             </probe-results>
           </result-info>
         </lsp-ping>
       </lsp-pings>
     </data>
   </rpc-reply>

8.  Security Considerations

   The YANG module specified in this document defines a schema for data
   that is designed to be accessed via network management protocols such
   as NETCONF [RFC6241] or RESTCONF [RFC8040].  The lowest NETCONF layer
   is the secure transport layer, and the mandatory-to-implement secure
   transport is Secure Shell (SSH) [RFC6242].  The lowest RESTCONF layer
   is HTTPS, and the mandatory-to-implement secure transport is TLS
   [RFC8446].

   The NETCONF access control model [RFC8341] provides the means to
   restrict access for particular NETCONF or RESTCONF users to a pre-
   configured subset of all available NETCONF or RESTCONF protocol
   operations and content.

   Some of the RPC operations in this YANG module may be considered
   sensitive or vulnerable in some network environments.  It is thus
   important to control access to these operations.  These are the
   operations and their sensitivity/vulnerability:

   TBD

   The LSP ping YANG module inherits all security consideration of
   [RFC8029].

Zheng, et al.            Expires April 17, 2019                [Page 24]
Internet-Draft                LSP-Ping YANG                 October 2018

9.  IANA Considerations

   The IANA is requested to as assign a new namespace URI from the IETF
   XML registry.

   URI:TBA

Contributors

   Yanfeng Zhang

   Huawei Technologies

   zhangyanfeng@huawei.com

   Sam Aldrin

   Google

   aldrin.ietf@gmail.com

Acknowledgments

   TBD

12.  References

12.1.  Normative References

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/RFC2119, March 1997,
              <https://www.rfc-editor.org/info/rfc2119>.

   [RFC6020]  Bjorklund, M., Ed., "YANG - A Data Modeling Language for
              the Network Configuration Protocol (NETCONF)", RFC 6020,
              DOI 10.17487/RFC6020, October 2010,
              <https://www.rfc-editor.org/info/rfc6020>.

   [RFC7950]  Bjorklund, M., Ed., "The YANG 1.1 Data Modeling Language",
              RFC 7950, DOI 10.17487/RFC7950, August 2016,
              <https://www.rfc-editor.org/info/rfc7950>.

   [RFC8029]  Kompella, K., Swallow, G., Pignataro, C., Ed., Kumar, N.,
              Aldrin, S., and M. Chen, "Detecting Multiprotocol Label
              Switched (MPLS) Data-Plane Failures", RFC 8029,
              DOI 10.17487/RFC8029, March 2017,
              <https://www.rfc-editor.org/info/rfc8029>.

Zheng, et al.            Expires April 17, 2019                [Page 25]
Internet-Draft                LSP-Ping YANG                 October 2018

   [RFC8174]  Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
              2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
              May 2017, <https://www.rfc-editor.org/info/rfc8174>.

12.2.  Informative References

   [I-D.mahesh-netconf-persistent]
              Jethanandani, M., "NETCONF and persistent responses",
              draft-mahesh-netconf-persistent-00 (work in progress),
              October 2014.

   [RFC4560]  Quittek, J., Ed. and K. White, Ed., "Definitions of
              Managed Objects for Remote Ping, Traceroute, and Lookup
              Operations", RFC 4560, DOI 10.17487/RFC4560, June 2006,
              <https://www.rfc-editor.org/info/rfc4560>.

   [RFC6241]  Enns, R., Ed., Bjorklund, M., Ed., Schoenwaelder, J., Ed.,
              and A. Bierman, Ed., "Network Configuration Protocol
              (NETCONF)", RFC 6241, DOI 10.17487/RFC6241, June 2011,
              <https://www.rfc-editor.org/info/rfc6241>.

   [RFC6242]  Wasserman, M., "Using the NETCONF Protocol over Secure
              Shell (SSH)", RFC 6242, DOI 10.17487/RFC6242, June 2011,
              <https://www.rfc-editor.org/info/rfc6242>.

   [RFC6425]  Saxena, S., Ed., Swallow, G., Ali, Z., Farrel, A.,
              Yasukawa, S., and T. Nadeau, "Detecting Data-Plane
              Failures in Point-to-Multipoint MPLS - Extensions to LSP
              Ping", RFC 6425, DOI 10.17487/RFC6425, November 2011,
              <https://www.rfc-editor.org/info/rfc6425>.

   [RFC7594]  Eardley, P., Morton, A., Bagnulo, M., Burbridge, T.,
              Aitken, P., and A. Akhter, "A Framework for Large-Scale
              Measurement of Broadband Performance (LMAP)", RFC 7594,
              DOI 10.17487/RFC7594, September 2015,
              <https://www.rfc-editor.org/info/rfc7594>.

   [RFC8040]  Bierman, A., Bjorklund, M., and K. Watsen, "RESTCONF
              Protocol", RFC 8040, DOI 10.17487/RFC8040, January 2017,
              <https://www.rfc-editor.org/info/rfc8040>.

   [RFC8287]  Kumar, N., Ed., Pignataro, C., Ed., Swallow, G., Akiya,
              N., Kini, S., and M. Chen, "Label Switched Path (LSP)
              Ping/Traceroute for Segment Routing (SR) IGP-Prefix and
              IGP-Adjacency Segment Identifiers (SIDs) with MPLS Data
              Planes", RFC 8287, DOI 10.17487/RFC8287, December 2017,
              <https://www.rfc-editor.org/info/rfc8287>.

Zheng, et al.            Expires April 17, 2019                [Page 26]
Internet-Draft                LSP-Ping YANG                 October 2018

   [RFC8341]  Bierman, A. and M. Bjorklund, "Network Configuration
              Access Control Model", STD 91, RFC 8341,
              DOI 10.17487/RFC8341, March 2018,
              <https://www.rfc-editor.org/info/rfc8341>.

   [RFC8342]  Bjorklund, M., Schoenwaelder, J., Shafer, P., Watsen, K.,
              and R. Wilton, "Network Management Datastore Architecture
              (NMDA)", RFC 8342, DOI 10.17487/RFC8342, March 2018,
              <https://www.rfc-editor.org/info/rfc8342>.

   [RFC8446]  Rescorla, E., "The Transport Layer Security (TLS) Protocol
              Version 1.3", RFC 8446, DOI 10.17487/RFC8446, August 2018,
              <https://www.rfc-editor.org/info/rfc8446>.

Authors' Addresses

   Lianshu Zheng
   Huawei Technologies
   China

   Email: vero.zheng@huawei.com

   Guangying Zheng
   Huawei Technologies
   China

   Email: zhengguangying@huawei.com

   Greg Mirsky
   ZTE Corp.
   USA

   Email: gregimirsky@gmail.com

   Reshad Rahman
   Cisco Systems
   Canada

   Email: rrahman@cisco.com

   Faisal Iqbal
   Cisco Systems

   Email: faiqbal@cisco.com

Zheng, et al.            Expires April 17, 2019                [Page 27]