BGP Extension for SR-MPLS Entropy Label Position
draft-ietf-idr-bgp-srmpls-elp-01

IDR                                                               Y. Liu
Internet-Draft                                                   S. Peng
Intended status: Standards Track                                     ZTE
Expires: 8 August 2024                                   5 February 2024

            BGP Extension for SR-MPLS Entropy Label Position
                    draft-ietf-idr-bgp-srmpls-elp-01

Abstract

   This document proposes extensions for BGP to indicate the entropy
   label position in the SR-MPLS label stack when delivering SR Policy
   via BGP.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at https://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on 8 August 2024.

Copyright Notice

   Copyright (c) 2024 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents (https://trustee.ietf.org/
   license-info) in effect on the date of publication of this document.
   Please review these documents carefully, as they describe your rights
   and restrictions with respect to this document.  Code Components
   extracted from this document must include Revised BSD License text as
   described in Section 4.e of the Trust Legal Provisions and are
   provided without warranty as described in the Revised BSD License.

Liu & Peng                Expires 8 August 2024                 [Page 1]
Internet-Draft            BGP Extension for ELP            February 2024

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   2
   2.  Conventions used in this document . . . . . . . . . . . . . .   3
     2.1.  Requirements Language . . . . . . . . . . . . . . . . . .   3
     2.2.  Terminology and Acronyms  . . . . . . . . . . . . . . . .   3
   3.  Entropy Label Position in SR-MPLS with the Controller . . . .   3
   4.  BGP Extensions for ELP in SR Policy . . . . . . . . . . . . .   5
   5.  Operation Considerations  . . . . . . . . . . . . . . . . . .   6
   6.  IANA Considerations . . . . . . . . . . . . . . . . . . . . .   7
   7.  Security Considerations . . . . . . . . . . . . . . . . . . .   8
   8.  Acknowledgement . . . . . . . . . . . . . . . . . . . . . . .   8
   9.  References  . . . . . . . . . . . . . . . . . . . . . . . . .   8
     9.1.  Normative References  . . . . . . . . . . . . . . . . . .   8
     9.2.  Informative References  . . . . . . . . . . . . . . . . .   8
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .   9

1.  Introduction

   Segment Routing (SR) leverages the source routing paradigm.  Segment
   Routing can be instantiated on MPLS data plane which is referred to
   as SR-MPLS [RFC8660].  SR-MPLS leverages the MPLS label stack to
   construct the SR path.

   Entropy labels (ELs) [RFC6790] are used in the MPLS data plane to
   provide entropy for load-balancing.  The idea behind the entropy
   label is that the ingress router computes a hash based on several
   fields from a given packet and places the result in an additional
   label named "entropy label".  Then, this entropy label can be used as
   part of the hash keys used by an LSR.  Using the entropy label as
   part of the hash keys reduces the need for deep packet inspection in
   the LSR while keeping a good level of entropy in the load-balancing.

   [RFC8662] proposes to use entropy labels for SR-MPLS networks and
   multiple <ELI, EL> pairs may be inserted in the SR-MPLS label stack.
   The ingress node may decide the number and position of the ELI/ELs
   which need to be inserted into the label stack, that is termed as ELP
   (Entropy Label Position) in this document.  But in some cases, the
   controller (e.g.  PCE) can be used to perform the SR-TE path
   computation as well as the Entropy Label Position which is useful for
   inter-domain scenarios.

   [I-D.ietf-idr-sr-policy-safi] specifies the way to use BGP to
   distribute one or more of the candidate paths of an SR Policy to the
   headend of that policy.

   This document proposes extensions for BGP to indicate the ELP in the
   segment list when delivering SR Policy via BGP in SR-MPLS networks.

Liu & Peng                Expires 8 August 2024                 [Page 2]
Internet-Draft            BGP Extension for ELP            February 2024

2.  Conventions used in this document

2.1.  Requirements Language

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
   "OPTIONAL" in this document are to be interpreted as described in BCP
   14 [RFC2119][RFC8174] when, and only when, they appear in all
   capitals, as shown here.

2.2.  Terminology and Acronyms

   EL: Entropy Label

   ELI: Entropy Label Indicator

   ELC: Entropy Label Capability

   ERLD: Entropy Readable Label Depth

   ELP: Entropy Label Position

   BMI: Base MPLS Imposition is the number of MPLS labels that can be
   imposed inclusive of all service/transport/special labels.

   MSD: Maximum SID Depth

   BMI-MSD: A type of MSD signals the BMI of a node.

   ERLD-MSD: A type of MSD advertises the ERLD of a node.

3.  Entropy Label Position in SR-MPLS with the Controller

   As described in [RFC8662] section 7, ELI/EL placement is not an easy
   decision, multiple criteria may be taken into account.

   First is the BMI-MSD[RFC8491], it defines the maximum number of
   labels that a particular node can impose on a packet, and it is a
   limit when the ingress node imposing ELI/EL pairs on the SR label
   stack.

Liu & Peng                Expires 8 August 2024                 [Page 3]
Internet-Draft            BGP Extension for ELP            February 2024

   The Entropy Readable Label Depth(ERLD) [RFC8662] is another important
   parameter to consider when inserting an ELI/EL.  The ERLD is defined
   as the number of labels a router can both read in an MPLS packet
   received on its incoming interface(s) and use in its load-balancing
   function.  An ELI/EL pair must be within the ERLD of the LSR in order
   for the LSR to use the EL during load-balancing.  It's necessary to
   get the ERLD of the nodes along the SR path to achieve efficient
   load-balancing.

   An implementation MAY try to evaluate if load-balancing is really
   expected at a particular node based on the segment type of its label,
   which also influences the ELP of a segment list.

   Other criteria includes maximizing number of LSRs that will load-
   balance, preference for a part of the path, and etc.  Using which
   criteria and how to decide the ELP based on the criteria is a matter
   of implementation.

   As shown in Figure 1, in the inter-domain scenario, a path from A to
   Z is required, a centralized controller performs the computation of
   the end-to-end path, along which traffic load-balancing is required.

    ....................   ....................    .....................
    .                  .   .                  .    .                   .
    .+---+       +---+ .   . +---+      +---+ .    .+---+      +----+  .
    .| A |-------| B |------ | C |------| X |-------| Y |------| Z  |  .
    .+---+       +---+ .   . +---+      +---+ .    .+---+      +----+  .
    .     domain 1     .   .      domain 2    .    .     domain 3      .
    ....................   ....................    .....................

         Figure 1: Entropy Labels in SR-MPLS Inter-Domain Scenario

   When the headend node in the first domain can't get the information
   of the nodes/SIDs in other domains, e.g, the ERLD of each node or the
   type of the SID bounded to a node/link, it's difficult for the
   headend node to decide the ELP of the segment list for the path.

   Performing the computation of the ELP by the controller is an
   alternate, since it's easier for the controller to get the required
   information along the segment list prescribed by itself.

   For example, the ERLD can be advertised as ERLD-MSD via IS-
   IS[RFC9088] and OSPF[RFC9089] within the domain, in each domain, one
   or more nodes are configured with BGP-LS so the controller can get
   the ERLD-MSD of all the nodes through BGP-LS[RFC9085].  The
   controller can acquire the BMI-MSD of the headend node or the Binding
   SID anchor node via BGP-LS[RFC8814] or PCEP[RFC8664].

Liu & Peng                Expires 8 August 2024                 [Page 4]
Internet-Draft            BGP Extension for ELP            February 2024

   Another benefit of utilizing the controller to calculate ELP is that
   if the criteria or calculation algorithm is changed, the
   corresponding modification only needs to be made on the controller
   instead of each headend node in the network.

   When the controller performs the computation of the the ELP for a
   segment list, the considerations for the placement of ELI/ELs
   introduced in [RFC8662] are still applicable.  How the controller
   computes the ELP is out of scope of the document.

   After the ELP of an SR path is decided, the controller SHOULD inform
   the result to the headend node of the path, so the node knows where
   to insert the ELI/ELs when needed.  Section 4 proposes the detailed
   extensions for BGP to carry this information.

4.  BGP Extensions for ELP in SR Policy

   As defined in [I-D.ietf-idr-sr-policy-safi], the SR Policy encoding
   structure is as follows:

          SR Policy SAFI NLRI: <Distinguisher, Policy-Color, Endpoint>
          Attributes:
             Tunnel Encaps Attribute (23)
                Tunnel Type: SR Policy
                    Binding SID
                    Preference
                    Priority
                    Policy Name
                    Explicit NULL Label Policy (ENLP)
                    Segment List
                        Weight
                        Segment
                        Segment
                        ...
                    ...

   This document defines a new ELP sub-TLV within Segment List sub-TLV.
   The ELP sub-TLV has the following format:

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |     Type      |   Length      |         RESERVED              |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   Where,

   Type: TBD.

Liu & Peng                Expires 8 August 2024                 [Page 5]
Internet-Draft            BGP Extension for ELP            February 2024

   Length: Specifies the length of the value field (i.e., not including
   Type and Length fields) in terms of octets.  The value MUST be 2.

   RESERVED: 2 octet of reserved bits.  MUST be unset on transmission
   and MUST be ignored on receipt.

   The ELP sub-TLV, when present, indicates that the <ELI, EL> label
   pair SHOULD be inserted at this position.  It MAY appear multiple
   times in the Segment List sub-TLV.

   The new SR Policy encoding structure with ELP sub-TLV is expressed as
   below:

          SR Policy SAFI NLRI: <Distinguisher, Policy-Color, Endpoint>
          Attributes:
             Tunnel Encaps Attribute (23)
                Tunnel Type: SR Policy
                    Binding SID
                    Preference
                    Priority
                    Policy Name
                    Explicit NULL Label Policy (ENLP)
                    Segment List
                        Weight
                        Segment
                        Segment
                        ELP
                        Segment
                        ...
                        Segment
                        ELP
                        Segment
                        Segment
                        ...
                    ...

5.  Operation Considerations

   After obtaining the topolopy of the network and other necessary
   criterias for determining ELP, the controller calculates the path
   information of the SR-TE Policy based on these information and builds
   the SR-TE Policy from the headend to the endpoint.  And then it
   delivers the SR path information with the segment list as well as the
   ELP included to the headend, leveraging the BGP extension introduced
   in this document.

Liu & Peng                Expires 8 August 2024                 [Page 6]
Internet-Draft            BGP Extension for ELP            February 2024

   The <ELI, EL> label pair insertion is indicated at the segment list
   level.  The following example shows how a headend node operates after
   the ELP sub-TLV is introduced.

   Node A receives an SR Policy NLRI with an Segment List sub-TLV from
   the controller.  The Segment List sub-TLV contains multiple Segment
   sub-TLVs and ELP sub-TLVs, e.g, <S1, S2, S3,ELP, S4, S5, S6, ELP>, it
   indicates that if load-balancing is required, two <ELI, EL> pairs
   SHOULD be inserted into the label stack of the SR-TE forwarding
   entry, respectively after the Label for S3 and Label for S6.

   The value of EL is supplemented by the ingress node according to
   load-balancing function of the appropriate keys extracted from a
   given packet.  After inserting ELI/ELs, the label stack on the
   ingress node would be <S1, S2, S3, ELI, EL, S4, S5, S6, ELI, EL>.

   If the SR Policy is delivered without the ELP sub-TLV, the headend
   node MAY still insert ELI/ELs based on its own decision, as the
   legacy behavior of ELI/EL insertion defined in [RFC8662], making it
   inconvenient for network operation and troubleshooting.  So it is
   RECOMMENDED that at at least within the same SR policy, the behavior
   SHOULD be consistent, that is, either the headend node inserts the
   ELI/ELs based on the ELP sub-TLV received or it makes its own
   decision regardless of the existence of the ELP sub-TLV.

   The Maximum SID Depth defines the maximum number of labels that a
   particular node can impose on a packet.  When ELI/EL insertion is
   required, the number of segments and ELI/ELs to be inserted in the
   segment list SHOULD not exceed the BMI-MSD limit.  In this case,
   depending on whether ELI/EL(s) are required to be inserted and
   whether the headend node has sufficient BMI-MSD, the segment list
   delivered by the controller to the headend MAY be different.  And
   with the additional constraints on ELI/EL insertion, the number of
   valid paths may be reduced, in some cases there may be no available
   path.  Whether the ELI/EL insertion should be considered when
   computing the SR policy MAY be based on the configuration or local
   policy on the controller, or some control plane mechanism between the
   headend and the controller MAY be used, the details are out of the
   scope of this document.

6.  IANA Considerations

   This document defines a new sub-TLV in the registry "SR Policy List
   Sub-TLVs" [I-D.ietf-idr-sr-policy-safi] to be assigned by IANA:

           Codepoint   Description                           Reference
           -------------------------------------------------------------
           TBD         ELP Sub-TLV                         This document

Liu & Peng                Expires 8 August 2024                 [Page 7]
Internet-Draft            BGP Extension for ELP            February 2024

7.  Security Considerations

   Procedures and protocol extensions defined in this document do not
   introduce any new security considerations beyond those already listed
   in [RFC8662] and [I-D.ietf-idr-sr-policy-safi].

8.  Acknowledgement

   The authors would like to thank Ketan Talaulikar, Jie Dong and Nat
   Kao for their helpful review and comments.

9.  References

9.1.  Normative References

   [I-D.ietf-idr-sr-policy-safi]
              Previdi, S., Filsfils, C., Talaulikar, K., Mattes, P., and
              D. Jain, "Advertising Segment Routing Policies in BGP",
              Work in Progress, Internet-Draft, draft-ietf-idr-sr-
              policy-safi-00, 4 February 2024,
              <https://datatracker.ietf.org/doc/html/draft-ietf-idr-sr-
              policy-safi-00>.

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/RFC2119, March 1997,
              <https://www.rfc-editor.org/info/rfc2119>.

   [RFC6790]  Kompella, K., Drake, J., Amante, S., Henderickx, W., and
              L. Yong, "The Use of Entropy Labels in MPLS Forwarding",
              RFC 6790, DOI 10.17487/RFC6790, November 2012,
              <https://www.rfc-editor.org/info/rfc6790>.

   [RFC8174]  Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
              2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
              May 2017, <https://www.rfc-editor.org/info/rfc8174>.

   [RFC8662]  Kini, S., Kompella, K., Sivabalan, S., Litkowski, S.,
              Shakir, R., and J. Tantsura, "Entropy Label for Source
              Packet Routing in Networking (SPRING) Tunnels", RFC 8662,
              DOI 10.17487/RFC8662, December 2019,
              <https://www.rfc-editor.org/info/rfc8662>.

9.2.  Informative References

Liu & Peng                Expires 8 August 2024                 [Page 8]
Internet-Draft            BGP Extension for ELP            February 2024

   [RFC8491]  Tantsura, J., Chunduri, U., Aldrin, S., and L. Ginsberg,
              "Signaling Maximum SID Depth (MSD) Using IS-IS", RFC 8491,
              DOI 10.17487/RFC8491, November 2018,
              <https://www.rfc-editor.org/info/rfc8491>.

   [RFC8660]  Bashandy, A., Ed., Filsfils, C., Ed., Previdi, S.,
              Decraene, B., Litkowski, S., and R. Shakir, "Segment
              Routing with the MPLS Data Plane", RFC 8660,
              DOI 10.17487/RFC8660, December 2019,
              <https://www.rfc-editor.org/info/rfc8660>.

   [RFC8664]  Sivabalan, S., Filsfils, C., Tantsura, J., Henderickx, W.,
              and J. Hardwick, "Path Computation Element Communication
              Protocol (PCEP) Extensions for Segment Routing", RFC 8664,
              DOI 10.17487/RFC8664, December 2019,
              <https://www.rfc-editor.org/info/rfc8664>.

   [RFC8814]  Tantsura, J., Chunduri, U., Talaulikar, K., Mirsky, G.,
              and N. Triantafillis, "Signaling Maximum SID Depth (MSD)
              Using the Border Gateway Protocol - Link State", RFC 8814,
              DOI 10.17487/RFC8814, August 2020,
              <https://www.rfc-editor.org/info/rfc8814>.

   [RFC9085]  Previdi, S., Talaulikar, K., Ed., Filsfils, C., Gredler,
              H., and M. Chen, "Border Gateway Protocol - Link State
              (BGP-LS) Extensions for Segment Routing", RFC 9085,
              DOI 10.17487/RFC9085, August 2021,
              <https://www.rfc-editor.org/info/rfc9085>.

   [RFC9088]  Xu, X., Kini, S., Psenak, P., Filsfils, C., Litkowski, S.,
              and M. Bocci, "Signaling Entropy Label Capability and
              Entropy Readable Label Depth Using IS-IS", RFC 9088,
              DOI 10.17487/RFC9088, August 2021,
              <https://www.rfc-editor.org/info/rfc9088>.

   [RFC9089]  Xu, X., Kini, S., Psenak, P., Filsfils, C., Litkowski, S.,
              and M. Bocci, "Signaling Entropy Label Capability and
              Entropy Readable Label Depth Using OSPF", RFC 9089,
              DOI 10.17487/RFC9089, August 2021,
              <https://www.rfc-editor.org/info/rfc9089>.

Authors' Addresses

   Yao Liu
   ZTE
   Nanjing
   China
   Email: liu.yao71@zte.com.cn

Liu & Peng                Expires 8 August 2024                 [Page 9]
Internet-Draft            BGP Extension for ELP            February 2024

   Shaofu Peng
   ZTE
   Nanjing
   China
   Email: peng.shaofu@zte.com.cn

Liu & Peng                Expires 8 August 2024                [Page 10]