PCEP Extension for Native IP Network
draft-ietf-pce-pcep-extension-native-ip-17
The information below is for an old version of the document.
| Document | Type | Active Internet-Draft (pce WG) | |
|---|---|---|---|
| Authors | Aijun Wang , Boris Khasanov , Sheng Fang , Ren Tan , Chun Zhu | ||
| Last updated | 2022-02-06 (Latest revision 2021-08-15) | ||
| Replaces | draft-wang-pce-pcep-extension-native-ip | ||
| Stream | Internet Engineering Task Force (IETF) | ||
| Formats | plain text html xml htmlized pdfized bibtex | ||
| Stream | WG state | WG Document | |
| Document shepherd | (None) | ||
| IESG | IESG state | I-D Exists | |
| Consensus boilerplate | Unknown | ||
| Telechat date | (None) | ||
| Responsible AD | (None) | ||
| Send notices to | (None) |
draft-ietf-pce-pcep-extension-native-ip-17
PCE Working Group A. Wang
Internet-Draft China Telecom
Intended status: Standards Track B. Khasanov
Expires: 11 August 2022 Yandex LLC
S. Fang
R. Tan
Huawei Technologies,Co.,Ltd
C. Zhu
ZTE Corporation
7 February 2022
PCEP Extension for Native IP Network
draft-ietf-pce-pcep-extension-native-ip-17
Abstract
This document defines the Path Computation Element Communication
Protocol (PCEP) extension for Central Control Dynamic Routing (CCDR)
based application in Native IP network. The scenario and framework
of CCDR in native IP is described in [RFC8735] and [RFC8821]. This
draft describes the key information that is transferred between Path
Computation Element (PCE) and Path Computation Clients (PCC) to
accomplish the End to End (E2E) traffic assurance in Native IP
network under central control mode.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on 11 August 2022.
Copyright Notice
Copyright (c) 2022 IETF Trust and the persons identified as the
document authors. All rights reserved.
Wang, et al. Expires 11 August 2022 [Page 1]
Internet-Draft PCEP Extension for Native IP Network February 2022
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents (https://trustee.ietf.org/
license-info) in effect on the date of publication of this document.
Please review these documents carefully, as they describe your rights
and restrictions with respect to this document. Code Components
extracted from this document must include Revised BSD License text as
described in Section 4.e of the Trust Legal Provisions and are
provided without warranty as described in the Revised BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Conventions used in this document . . . . . . . . . . . . . . 3
3. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 3
4. Capability Advertisemnt . . . . . . . . . . . . . . . . . . . 4
4.1. Open message . . . . . . . . . . . . . . . . . . . . . . 4
5. PCEP messages . . . . . . . . . . . . . . . . . . . . . . . . 4
5.1. The PCInitiate message . . . . . . . . . . . . . . . . . 5
5.2. The PCRpt message . . . . . . . . . . . . . . . . . . . . 6
6. PCECC Native IP TE Procedures . . . . . . . . . . . . . . . . 7
6.1. BGP Session Establishment Procedures . . . . . . . . . . 7
6.2. Explicit Route Establish Procedures . . . . . . . . . . . 9
6.3. BGP Prefix Advertisement Procedures . . . . . . . . . . . 12
7. New PCEP Objects . . . . . . . . . . . . . . . . . . . . . . 14
7.1. CCI Object . . . . . . . . . . . . . . . . . . . . . . . 14
7.2. BGP Peer Info Object . . . . . . . . . . . . . . . . . . 15
7.3. Explicit Peer Route Object . . . . . . . . . . . . . . . 17
7.4. Peer Prefix Advertisement Object . . . . . . . . . . . . 20
8. End to End Path Protection . . . . . . . . . . . . . . . . . 21
9. Re-Delegation and Clean up . . . . . . . . . . . . . . . . . 21
10. BGP Considerations . . . . . . . . . . . . . . . . . . . . . 22
11. New Error-Types and Error-Values Defined . . . . . . . . . . 22
12. Deployment Considerations . . . . . . . . . . . . . . . . . . 23
13. Security Considerations . . . . . . . . . . . . . . . . . . . 24
14. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 24
14.1. Path Setup Type Registry . . . . . . . . . . . . . . . . 24
14.2. PCECC-CAPABILITY sub-TLV's Flag field . . . . . . . . . 24
14.3. PCEP Object Types . . . . . . . . . . . . . . . . . . . 25
14.4. PCEP-Error Object . . . . . . . . . . . . . . . . . . . 25
15. Contributor . . . . . . . . . . . . . . . . . . . . . . . . . 26
16. Acknowledgement . . . . . . . . . . . . . . . . . . . . . . . 26
17. Normative References . . . . . . . . . . . . . . . . . . . . 26
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 28
Wang, et al. Expires 11 August 2022 [Page 2]
Internet-Draft PCEP Extension for Native IP Network February 2022
1. Introduction
Generally, Multiprotocol Label Switching Traffic Engineering (MPLS-
TE) requires the corresponding network devices support Multiprotocol
Label Switching (MPLS) or Resource ReSerVation Protocol (RSVP)/Label
Distribution Protocol (LDP) technologies to assure the End-to-End
(E2E) traffic performance. In Segment Routing either IGP extensions
or BGP are used to steer a packet through an SR Policy instantiated
as an ordered list of instructions called "segments". But in native
IP network, there will be no such signaling protocol to synchronize
the action among different network devices. It is necessary to use
the central control mode that described in [RFC8283] to correlate the
forwarding behavior among different network devices. [RFC8821]
describes the architecture and solution philosophy for the E2E
traffic assurance in Native IP network via Multi Border Gateway
Protocol (BGP) solution. This draft describes the corresponding Path
Computation Element Communication Protocol (PCEP) extensions to
transfer the key information about BGP peer info, peer prefix
advertisement and the explicit peer route on on-path routers.
2. Conventions used in this document
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in BCP
14 [RFC2119] [RFC8174] when, and only when, they appear in all
capitals, as shown here.
3. Terminology
This document uses the following terms defined in [RFC5440]: PCE,
PCEP
The following terms are defined in this document:
* CCDR: Central Control Dynamic Routing
* E2E: End to End
* BPI: BGP Peer Info
* EPR: Explicit Peer Route
* PPA: Peer Prefix Advertisement
* QoS: Quality of Service
Wang, et al. Expires 11 August 2022 [Page 3]
Internet-Draft PCEP Extension for Native IP Network February 2022
4. Capability Advertisemnt
4.1. Open message
During the PCEP Initialization Phase, PCEP Speakers (PCE or PCC)
advertise their support of Native IP extensions.
This document defines a new Path Setup Type (PST) [RFC8408] for
Native-IP, as follows:
* PST = TBD1: Path is a Native IP path as per [RFC8821].
A PCEP speaker MUST indicate its support of the function described in
this document by sending a PATH-SETUP-TYPE-CAPABILITY TLV in the OPEN
object with this new PST included in the PST list.
[RFC9050] defined the PCECC-CAPABILITY sub-TLV to exchange
information about their PCECC capability. A new flag is defined in
PCECC-CAPABILITY sub-TLV for Native IP:
N (NATIVE-IP-TE-CAPABILITY - 1 bit - TBD2): If set to 1 by a PCEP
speaker, it indicates that the PCEP speaker is capable for TE in
Native IP network as specified in this document. The flag MUST be
set by both the PCC and PCE in order to support this extension.
If a PCEP speaker receives the PATH-SETUP-TYPE-CAPABILITY TLV with
the newly defined path setup type, but without the N bit set in
PCECC-CAPABILITY sub-TLV, it MUST:
* Send a PCErr message with Error-Type=10(Reception of an invalid
object) and Error-Value TBD3(PCECC NATIVE-IP-TE-CAPABILITY bit is
not set).
* Terminate the PCEP session
5. PCEP messages
PCECC Native IP TE solution utilizing the existing PCE LSP Initate
Request message(PCInitiate)[RFC8281], and PCE Report message(PCRpt)
[RFC8281] to accomplish the multi BGP sessions establishment, E2E TE
path deployment, and route prefixes advertisement among different BGP
sessions. A new PST for Native-IP is used to indicate the path setup
based on TE in Native IP networks.
The extended PCInitiate message described in [RFC9050] is used to
download or cleanup central controller's instructions (CCIs).
[RFC9050] specifies an object called CCI for the encoding of central
controller's instructions. This document specify a new CCI object-
Wang, et al. Expires 11 August 2022 [Page 4]
Internet-Draft PCEP Extension for Native IP Network February 2022
type for Native IP. The PCEP messages are extended in this document
to handle the PCECC operations for Native IP. Three new PCEP Objects
(BGP Peer Info (BPI) Object, Explicit Peer Route (EPR) Object and
Peer Prefix Advertisement (PPA) Object) are defined in this document.
Refer toSection 7 for detail object definitions.
5.1. The PCInitiate message
The PCInitiate Message defined in [RFC8281] and extended in [RFC9050]
is further extended to support Native-IP CCI.
The format of the extended PCInitiate message is as follows:
<PCInitiate Message> ::= <Common Header>
<PCE-initiated-lsp-list>
Where:
<Common Header> is defined in [RFC5440]
<PCE-initiated-lsp-list> ::= <PCE-initiated-lsp-request>
[<PCE-initiated-lsp-list>]
<PCE-initiated-lsp-request> ::=
(<PCE-initiated-lsp-instantiation>|
<PCE-initiated-lsp-deletion>|
<PCE-initiated-lsp-central-control>)
<PCE-initiated-lsp-central-control> ::= <SRP>
<LSP>
(<cci-list>|
((<BPI>|<EPR>|<PPA>)
<CCI>))
<cci-list> ::= <CCI>
[<cci-list>]
Where:
<cci-list> is as per
[I-D.ietf-pce-pcep-extension-for-pce-controller].
<PCE-initiated-lsp-instantiation> and
<PCE-initiated-lsp-deletion> are as per
[RFC8281].
The LSP and SRP objects are defined in [RFC8231].
When PCInitiate message is used create Native IP instructions, the
SRP, LSP and CCI objects MUST be present. The error handling for
missing SRP, LSP or CCI object is as per [RFC9050]. Further only one
of BPI, EPR, or PPA object MUST be present. The PLSP-ID within the
Wang, et al. Expires 11 August 2022 [Page 5]
Internet-Draft PCEP Extension for Native IP Network February 2022
LSP object should be set by PCC uniquely according to the Symbolic
Path Name TLV that included in the CCI object. The Symbolic Path
Name is used by the PCE/PCC to identify uniquely the E2E native IP TE
path.
If none of them are present, the receiving PCC MUST send a PCErr
message with Error-type=6 (Mandatory Object missing) and Error-
value=TBD4 (Native IP object missing). If there are more than one of
BPI, EPR or PPA object are presented, the receiving PCC MUST send a
PCErr message with Error-type=19(Invalid Operation) and Error-
value=TBD5(Only one of the BPI, EPR or PPA object can be included in
this message).
To cleanup the SRP object must set the R (remove) bit.
5.2. The PCRpt message
The PCRpt message is used to acknowledge the Native-IP instructions
received from the central controller (PCE).
The format of the PCRpt message is as follows:
<PCRpt Message> ::= <Common Header>
<state-report-list>
Where:
<state-report-list> ::= <state-report>[<state-report-list>]
<state-report> ::= (<lsp-state-report>|
<central-control-report>)
<lsp-state-report> ::= [<SRP>]
<LSP>
<path>
<central-control-report> ::= [<SRP>]
<LSP>
(<cci-list>|
((<BPI>|<EPR>|<PPA>)
<CCI>))
Where:
<path> is as per [RFC8231] and the LSP and SRP object are
also defined in [RFC8231].
The error handling for missing CCI object is as per [RFC9050].
Further only one of BPI, EPR, or PPA object MUST be present.
Wang, et al. Expires 11 August 2022 [Page 6]
Internet-Draft PCEP Extension for Native IP Network February 2022
If none of them are present, the receiving PCE MUST send a PCErr
message with Error-type=6 (Mandatory Object missing) and Error-
value=TBD4 ( Native IP object missing). If there are more than one
of BPI, EPR or PPA object are presented, the receiving PCE MUST send
a PCErr message with Error-type=19(Invalid Operation) and Error-
value=TBD5(Only one of the BPI, EPR or PPA object can be included in
this message).
6. PCECC Native IP TE Procedures
The detail procedures for the TE in native IP environment are
described in the following sections.
6.1. BGP Session Establishment Procedures
The PCInitiate message can be used to configure the parameters for a
BGP peer session using the PCInitiate and PCRpt message pair. This
pair of PCE messages is exchanged with a PCE function attached to
each BGP peer which needs to be configured. After the BGP peer
session has been configured via this pair of PCE messages the BGP
session establishment process operates in a normal fashion. All BGP
peers are configured for peer to peer communication whether the peers
are E-BGP peers or I-BGP peers. One of the IBGP topologies requires
that multiple I-BGPs peers operate in a route-reflector I-BGP peer
topology. The example below shows two I-BGP route reflector clients
interacting with one Route Reflector (RR), but Route Reflector
topologies may have up to 100s of clients. Centralized configuration
via PCE provides mechanisms to scale auto-configuration of small and
large topologies.
The PCInitiate message should be sent to PCC which acts as BGP router
and/or route reflector(RR).
The route reflector topology for a single AS is shown in Figure 1.
The BGP routers R1, R3, and R7 are within a single AS. R1 and R7 are
BGP router-reflector clients, and R3 is a Route Reflector. The
PCInitiate message should be sent all of the BGP routers that need to
be configured R1 (M3), R3 (M2 & M3), and R7 (M4).
PCInitiate message creates an auto-configuration function for these
BGP peers providing the indicated Peer AS and the Local/Peer IP
Address.
When PCC receives the BPI and CCI object (with the R bit set to 0 in
SRP object) in PCInitiate message, the PCC should try to establish
the BGP session with the indicated Peer AS and Local/Peer IP address.
Wang, et al. Expires 11 August 2022 [Page 7]
Internet-Draft PCEP Extension for Native IP Network February 2022
When PCC creates successfully the BGP session that is indicated by
the associated information, it should report the result via the PCRpt
messages, with BPI object and the corresponding SRP and CCI object
included.
When PCC receives this message with the R bit set to 1 in SRP object
in PCInitiate message, the PCC should clear the BGP session that
indicated by the BPI object.
When PCC clears successfully the specified BGP session, it should
report the result via the PCRpt message, with the BPI object
included, and the corresponding SRP and CCI object.
+------------------+
+-----------+ PCE +----------+
| +--------^---------+ |
| | |
M2/M2-R & M3/M3-R
| | |
| +---v---+ |
+---------------+ R3(RR)+-----------------+
| +-------+ |
M1/M1-R M4/M4-R
| |
+v-+ +--+ +--+ +-v+
|R1+----------+R5+----------+R6+---------+R7|
++-+ +--+ +--+ +-++
| |
| +--+ +--+ |
+------------+R2+----------+R4+-----------+
+--+ +--+
Figure 1: BGP Session Establishment Procedures(R3 act as RR)
The message number, message peers, message type and message key
parameters in the above figures are shown in below table:
Wang, et al. Expires 11 August 2022 [Page 8]
Internet-Draft PCEP Extension for Native IP Network February 2022
Table 1: Message Information
+-------------------------------------------------------------+
| No.| Peers| Type | Message Key Parameters |
+-------------------------------------------------------------+
|M1 |PCE/R1|PCInitiate|CC-ID=X1(Symbolic Path Name=Class A) |
|M1-R| |PCRpt |BPI Object(Local_IP=R1_A,Peer_IP=R3_A)|
+-------------------------------------------------------------+
|M2 |PCE/R3|PCInitiate|CC-ID=X2(Symbolic Path Name=Class A) |
|M2-R| |PCRpt |BPI Object(Local_IP=R3_A,Peer_IP=R1_A)|
+-------------------------------------------------------------+
|M3 |PCE/R3|PCInitiate|CC-ID=X3(Symbolic Path Name=Class A) |
|M3-R| |PCRpt |BPI Object(Local_IP=R3_A,Peer_IP=R7_A)|
+-------------------------------------------------------------+
|M4 |PCE/R7|PCInitiate|CC-ID=X4(Symbolic Path Name=Class A) |
|M4-R| |PCRpt |BPI Object(Local_IP=R7_A,Peer_IP=R3_A)|
+-------------------------------------------------------------+
If the PCC cannot establish the BGP session that required by this
object, it should report the error values via PCErr message with the
newly defined error type(Error-type=TBD6) and error value(Error-
value=TBD7, Peer AS not match; or Error-Value=TBD8, Peer IP can't be
reached), which is indicated in Section 11
If the Local IP Address or Peer IP Address within BPI object is used
in other existing BGP sessions, the PCC should report such error
situation via PCErr message with Err-type=TBD6 and error value(Error-
value=TBD9, Local IP is in use; Error-value=TBD10, Remote IP is in
use).
6.2. Explicit Route Establish Procedures
The explicit route establishment procedures can be used to install a
route via PCE in the PCC/BGP Peer, using PCInitiate and PCRpt message
pair. Although the BGP policy might redistribute the routes
installed by explicit route, the PCE-BGP implementation needs to
prohibit the redistribution of the explicit route. PCE explicit
routes operate similar to static routes installed by network
management protocols (netconf/restconf) but the routes are associated
with the PCE routing module. Explicit route installations (like NM
static routes) must carefully install and uninstall static routes in
an specific order so that the pathways are established without loops.
The PCInitiate message should be sent to the on-path routers
respectively. In the example, for explicit route from R1 to R7, the
PCInitiate message should be sent to R1(M1), R2(M2) and R4(M3), as
shown in Figure 2. For explicit route from R7 to R1, the PCInitiate
message should be sent to R7(M1), R4(M2) and R2(M3), as shown in
Figure 3.
Wang, et al. Expires 11 August 2022 [Page 9]
Internet-Draft PCEP Extension for Native IP Network February 2022
When PCC receives the EPR and the CCI object (with the R bit set to 0
in SRP object) in PCInitiate message, the PCC should install the
explicit route to the the peer.
When PCC install successfully the explicit route to the peer, it
should report the result via the PCRpt messages, with EPR object and
the corresponding SRP and CCI object included.
When PCC receives the EPR and the CCI object with the R bit set to 1
in SRP object in PCInitiate message, the PCC should clear the
explicit route to the peer that indicated by the EPR object.
When PCC clear successfully the explicit route that indicated by this
object, it should report the result via the PCRpt message, with the
EPR object included, and the corresponding SRP and CCI object.
+------------------+
+----------+ PCE +
| +----^-----------^-+
| | |
| | |
| | +------+ |
+-----------------+R3(RR)+--|-------------+
M1/M1-R | +------+ | |
| | | |
+v-+ +--+ | | +--+ +--+
|R1+------+R5+---+-----------|---+R6+----+R7|
++-+ +--+ | | +--+ +-++
| M2/M2-R M3/M3-R |
| | | |
| +--v--+ +--v-+ |
+------------+- R2 +-----+ R4 +-----------+
+--+--+ +--+-+
Figure 2: Explicit Route Establish Procedures(From R1 to R7)
The message number, message peers, message type and message key
parameters in the above figures are shown in below table:
Wang, et al. Expires 11 August 2022 [Page 10]
Internet-Draft PCEP Extension for Native IP Network February 2022
Table 2: Message Information
+------------------------------------------------------------------+
| No.|Peers | Type | Message Key Parameters |
+------------------------------------------------------------------+
|M1 |PCE/R1|PCInitiate|CC-ID=X1(Symbolic Path Name=Class A) |
|M1-R| |PCRpt |EPR Object(Peer Address=R7_A,Next Hop=R2_A)|
+------------------------------------------------------------------+
|M2 |PCE/R2|PCInitiate|CC-ID=X2(Symbolic Path Name=Class A) |
|M2-R| |PCRpt |EPR Object(Peer Address=R7_A,Next Hop=R4_A)|
+------------------------------------------------------------------+
|M3 |PCE/R4|PCInitiate|CC-ID=X3(Symbolic Path Name=Class A) |
|M3-R| |PCRpt |EPR Object(Peer Address=R7_A,Next Hop=R7_A)|
+------------------------------------------------------------------+
+------------------+
+ PCE +-----------+
+----^-----------^-+ |
| | |
| | |
| +------+ | |
+-----------------+R3(RR)+--|-------------+
| | +------+ | M1/M1-R
| | | |
+--+ +--+ | | +--+ +-v+
|R1+------+R5+---+-----------|---+R6+----+R7|
++-+ +--+ | | +--+ +-++
| M3/M3-R M2/M2-R |
| | | |
| +--v--+ +--v-+ |
+------------+- R2 +-----+ R4 +-----------+
+--+--+ +--+-+
Figure 3: Explicit Route Establish Procedures(From R7 to R1)
The message number, message peers, message type and message key
parameters in the above figures are shown in below table:
Wang, et al. Expires 11 August 2022 [Page 11]
Internet-Draft PCEP Extension for Native IP Network February 2022
Table 3: Message Information
+------------------------------------------------------------------+
|No. |Peers | Type | Message Key Parameters |
+------------------------------------------------------------------+
|M1 |PCE/R7|PCInitiate|CC-ID=X1(Symbolic Path Name=Class A) |
|M1-R| |PCRpt |EPR Object(Peer Address=R1_A,Next Hop=R4_A)|
+------------------------------------------------------------------+
|M2 |PCE/R4|PCInitiate|CC-ID=X2(Symbolic Path Name=Class A) |
|M2-R| |PCRpt |EPR Object(Peer Address=R1_A,Next Hop=R2_A)|
+------------------------------------------------------------------+
|M3 |PCE/R2|PCInitiate|CC-ID=X3(Symbolic Path Name=Class A) |
|M3-R| |PCRpt |EPR Object(Peer Address=R1_A,Next Hop=R1_A)|
+------------------------------------------------------------------+
In order to avoid the transient loop during the deploy of explicit
peer route, the EPR object should be sent to the PCCs in the reverse
order of the E2E path. To remove the explicit peer route, the EPR
object should be sent to the PCCs in the same order of E2E path.
To accomplish ECMP effects, the PCE can send multiple EPR objects to
the same node, with the same route priority and peer address value
but different next hop addresses.
The PCC should verify that the next hop address is reachable. Upon
the error occurs, the PCC SHOULD send the corresponding error via
PCErr message, with an error information (Error-type=TBD6, Error-
value=TBD12, Explicit Peer Route Error) that defined in Section 11.
When the peer info is not the same as the peer info that indicated in
BPI object in PCC for the same path that is identified by Symbolic
Path Name TLV, an error (Error-type=TBD6, Error-value=17, EPR/BPI
Peer Info mismatch) should be reported via the PCErr message.
6.3. BGP Prefix Advertisement Procedures
The detail procedures for BGP prefix advertisement are shown below,
using PCInitiate and PCRpt message pair.
The PCInitiate message should be sent to PCC that acts as BGP peer
router only. In the example, it should be sent to R1(M1) or R7(M2)
respectively.
When PCC receives the PPA and the CCI object (with the R bit set to 0
in SRP object) in PCInitiate message, the PCC should send the
prefixes indicated in this object to the appointed BGP peer.
Wang, et al. Expires 11 August 2022 [Page 12]
Internet-Draft PCEP Extension for Native IP Network February 2022
When PCC sends successfully the prefixes to the appointed BGP peer,
it should report the result via the PCRpt messages, with PPA object
and the corresponding SRP and CCI object included.
When PCC receives the PPA and the CCI object with the R bit set to 1
in SRP object in PCInitiate message, the PCC should withdraw the
prefixes advertisement to the peer that indicated by this object.
When PCC withdraws successfully the prefixes that indicated by this
object, it should report the result via the PCRpt message, with the
PPA object included, and the corresponding SRP and CCI object.
The allowed AFI/SAFI for the IPv4 BGP session should be 1/1(IPv4
prefix) and the allowed AFI/SAFI for the IPv6 BGP session should be
2/1(IPv6 prefix). If mismatch occur, an error(Error-type=TBD6,
Error-value=TBD18, BPI/PPR address family mismatch) should be
reported via PCErr message.
When the peer info is not the same as the peer info that indicated in
BPI object in PCC for the same path that is identified by Symbolic
Path Name TLV, an error (Error-type=TBD6, Error-value=TBD19, PPA/BPI
peer info mismatch) should be reported via the PCErr message.
+------------------+
+----------+ PCE +-----------+
| +------------------+ |
| +--+ |
+------------------+R3+-------------------+
M1&M1-R +--+ M2&M2-R
| |
+v-+ +--+ +--+ +-v+
|R1+----------+R5+----------+R6+---------+R7|
++-+ +--+ +--+ +-++
(BGP Router) (BGP Router)
| |
| |
| +--+ +--+ |
+------------+R2+----------+R4+-----------+
Figure 4: BGP Prefix Advertisement Procedures
Wang, et al. Expires 11 August 2022 [Page 13]
Internet-Draft PCEP Extension for Native IP Network February 2022
Table 4: Message Information
+-----------------------------------------------------------+
|No. | Peers| Type | Message Key Parameters |
+-----------------------------------------------------------+
|M1 |PCE/R1|PCInitiate|CC-ID=X1(Symbolic Path Name=Class A)|
|M1-R| |PCRpt |PPA Object(Peer IP=R7_A,Prefix=1_A) |
+-----------------------------------------------------------+
|M2 |PCE/R7|PCInitiate|CC-ID=X2(Symbolic Path Name=Class A)|
|M2-R| |PCRpt |PPA Object(Peer IP=R1_A,Prefix=7_A) |
+-----------------------------------------------------------+
7. New PCEP Objects
One new CCI Object and three new PCEP objects are defined in this
draft. All new PCEP objects are as per [RFC5440]
7.1. CCI Object
The Central Control Instructions (CCI) Object is used by the PCE to
specify the forwarding instructions is defined in [RFC9050]. This
document defines another object-type for Native-IP.
CCI Object-Type is TBD13 for Native-IP as below
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| CC-ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Reserved | Flags |
+---------------------------------------------------------------+
| |
// Optional TLV //
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 5: CCI Object for Native IP
Figure 1
The field CC-ID is as described in [RFC9050]. Following fields are
defined for CCI Object-Type TBD13
Reserved: is set to zero while sending, ignored on receipt.
Flags: is used to carry any additional information pertaining to the
CCI. Currently no flag bits are defined.
Wang, et al. Expires 11 August 2022 [Page 14]
Internet-Draft PCEP Extension for Native IP Network February 2022
The Symbolic Path Name TLV [RFC8231] MUST be included in the CCI
Object-Type TBD13 to identify the E2E TE path in Native IP
environment and MUST be unique.
7.2. BGP Peer Info Object
The BGP Peer Info object is used to specify the information about the
peer that the PCC should establish the BGP relationship with. This
object should only be included and sent to the head and end router of
the E2E path in case there is no Route Reflection (RR) involved. If
the RR is used between the head and end routers, then such
information should be sent to head router, RR and end router
respectively.
By default, there MUST be no prefix be distributed via such BGP
session that established by this object.
By default, the Local/Peer IP address SHOULD be dedicated to the
usage of native IP TE solution, and SHOULD NOT be used by other BGP
sessions that established by manual or non PCE initiated
configuration.
BGP Peer Info Object-Class is TBD14
BGP Peer Info Object-Type is 1 for IPv4 and 2 for IPv6
The format of the BGP Peer Info object body for IPv4(Object-Type=1)
is as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Peer AS Number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ETTL | Reserved |T|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Local IP Address |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Peer IP Address |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Tunnel Source IP Address |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Tunnel Destination IP Address |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Additional TLVs |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 6: BGP Peer Info Object Body Format for IPv4
Wang, et al. Expires 11 August 2022 [Page 15]
Internet-Draft PCEP Extension for Native IP Network February 2022
The format of the BGP Peer Info object body for IPv6(Object-Type=2)
is as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Peer AS Number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ETTL | Reserved |T|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ +
| Local IP Address (16 bytes) |
+ +
| |
+ +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ +
| Peer IP Address (16 bytes) |
+ +
| |
+ +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ +
| Tunnel Source IP Address (16 bytes) |
+ +
| |
+ +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ +
| Tunnel Destination IP Address (16 bytes) |
+ +
| |
+ +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Additional TLVs |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 7: BGP Peer Info Object Body Format for IPv6
Peer AS Number: 4 Bytes, to indicate the AS number of Remote Peer.
Wang, et al. Expires 11 August 2022 [Page 16]
Internet-Draft PCEP Extension for Native IP Network February 2022
ETTL: 1 Byte, to indicate the multihop count for EBGP session. It
should be 0 and ignored when Local AS and Peer AS is same.
Reserved: is set to zero while sending, ignored on receipt.
T bit: Indicates whether the traffic that associated with the
prefixes advertised via this BGP session is transported via IPinIP
tunnel (when T bit is set) or not (when T bit is clear).
Local IP Address(4/16 Bytes): IP address of the local router, used to
peer with other end router. When Object-Type is 1, length is 4
bytes; when Object-Type is 2, length is 16 bytes.
Peer IP Address(4/16 Bytes): IP address of the peer router, used to
peer with the local router. When Object-Type is 1, length is 4
bytes; when Object-Type is 2, length is 16 bytes;
Tunnel Source IP Address(4/16 Bytes): IP address of the tunnel
source, should be owned by the local router. When Object-Type is 1,
length is 4 bytes; when Object-Type is 2, length is 16 bytes.
Tunnel Destination IP Address(4/16 Bytes): IP address of the tunnel
destination, should be owned by the peer router. When Object-Type is
1, length is 4 bytes; when Object-Type is 2, length is 16 bytes.
Should be different from the Peer IP Address.
Additional TLVs: TLVs that associated with this object, can be used
to convey other necessary information for dynamic BGP session
establishment. Their definition are out of the current document.
When PCC receives BPI object, with Object-Type=1, it should try to
establish BGP session with the peer in AFI/SAFI=1/1; when PCC
receives BPI object with Object-Type=2, it should try to establish
the BGP session with the peer in AFI/SAFI=2/1. Other BGP
capabilities,for example, Graceful Restart(GR) that enhance the BGP
performance should also be negotiated and used by default.
7.3. Explicit Peer Route Object
The Explicit Peer Route object is defined to specify the explicit
peer route to the corresponding peer address on each device that is
on the E2E assurance path. This Object should be sent to all the
devices that locates on the E2E assurance path that calculated by
PCE.
Wang, et al. Expires 11 August 2022 [Page 17]
Internet-Draft PCEP Extension for Native IP Network February 2022
The path established by this object should have higher priority than
other path calculated by dynamic IGP protocol, but should be lower
priority than the static route configured by manual or NETCONF or by
other means.
Explicit Peer Route Object-Class is TBD15.
Explicit Peer Route Object-Type is 1 for IPv4 and 2 for IPv6
The format of Explicit Peer Route object body for IPv4(Object-Type=1)
is as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Route Priority | Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Peer/Tunnel Destination Address |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Next Hop Address to the Peer/Tunnel Destination Address |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Additional TLVs |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 8: Explicit Peer Route Object Body Format for IPv4
The format of Explicit Peer Route object body for IPv6(Object-Type=2)
is as follows:
Wang, et al. Expires 11 August 2022 [Page 18]
Internet-Draft PCEP Extension for Native IP Network February 2022
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Route Priority | Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ +
| Peer Address/Tunnel Destination Address |
+ +
| |
+ +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ +
| Next Hop Address to the Peer/Tunnel Destination Address |
+ +
| |
+ +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Additional TLVs |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 9: Explicit Peer Route Object Body Format for IPv6
Route Priority: 2 Bytes, The priority of this explicit route. The
higher priority should be preferred by the device. This field is
used to indicate the backup path at each hop.
Reserved: is set to zero while sending, ignored on receipt.
Peer/Tunnel Destination Address: To indicate the peer address(4/16
Bytes). When T bit is set in the associated BPI object, use the
tunnel destination address in BPI object; when T bit is clear, use
the peer address in BPI object.
Next Hop Address to the Peer/Tunnel Destination Address: To indicate
the next hop address(4/16 Bytes) to the corresponding peer/tunnel
destination address.
Additional TLVs: TLVs that associated with this object, can be used
to convey other necessary information for explicit peer path
establishment. Their definitions are out of the current document.
Wang, et al. Expires 11 August 2022 [Page 19]
Internet-Draft PCEP Extension for Native IP Network February 2022
7.4. Peer Prefix Advertisement Object
The Peer Prefix Advertisement object is defined to specify the IP
prefixes that should be advertised to the corresponding peer. This
object should only be included and sent to the head/end router of the
end2end path.
The prefixes information included in this object MUST only be
advertised to the indicated peer, MUST NOT be advertised to other BGP
peers.
Peer Prefix Advertisement Object-Class is TBD16
Peer Prefix Advertisement Object-Type is 1 for IPv4 and 2 for IPv6
The format of the Peer Prefix Advertisement object body is as
follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Peer IPv4 Address |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
// IPv4 Prefix subobjects //
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Additional TLVs |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 10: Peer Prefix Advertisement Object Body Format for IPv4
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Peer IPv6 Address |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
// IPv6 Prefix subobjects //
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Additional TLVs |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 11: Peer Prefix Advertisement Object Body Format for IPv6
Peer IPv4 Address: 4 Bytes. Identifies the peer IPv4 address that
the associated prefixes will be sent to.
Wang, et al. Expires 11 August 2022 [Page 20]
Internet-Draft PCEP Extension for Native IP Network February 2022
IPv4 Prefix subojects: List of IPv4 Prefix subobjects that defined in
[RFC3209], identify the prefixes that will be sent to the peer that
identified by Peer IPv4 Address List.
Peer IPv6 Address: 16 Bytes. Identifies the peer IPv6 address that
the associated prefixes will be sent to.
IPv6 Prefix subojects: List of IPv6 Prefix subobjects that defined in
[RFC3209], identify the prefixes that will be sent to the peer that
identified by Peer IPv6 Address List.
Additional TLVs: TLVs that associated with this object, can be used
to convey other necessary information for prefixes advertisement.
Their definitions are out of the current document.
8. End to End Path Protection
[RFC8697] defines the path associations procedures between sets of
Label Switched Path (LSP). Such procedures can also be used for the
E2E path protection. To accomplish this, the PCE should attach the
ASSOCIATION object with the EPR object in the PCInitiate message,
with the association type set to 1 (Path Protection Association).
The Extended Association ID that included within the Extended
Association ID TLV, which is included in the ASSOCIATION object,
should be set to the Symbolic Path Name of different E2E path. This
PCinitiate should be sent to the head-end of the E2E path.
The head-end of the path can use the existing path detection
mechanism(for example, Bidirectional Forwarding Detection [RFC5880]),
to monitor the status of the active path. Once it detects the
failure, it can switch the backup protection path immediately.
9. Re-Delegation and Clean up
In case of a PCE failure, a new PCE can gain control over the central
controller instructions. As per the PCEP procedures in [RFC8281],
the State Timeout Interval timer is used to ensure that a PCE failure
does not result in automatic and immediate disruption for the
services. Similarly, as per [RFC9050], the central controller
instructions are not removed immediately upon PCE failure. Instead,
they could be re-delegated to the new PCE before the expiration of
this timer, or be cleaned up on the expiration of this timer. The
allows for network clean up without manual intervention. The PCC
MUST support the removal of CCI as one of the behaviors applied on
expiration of the State Timeout Interval timer.
Wang, et al. Expires 11 August 2022 [Page 21]
Internet-Draft PCEP Extension for Native IP Network February 2022
10. BGP Considerations
This draft defines the procedures and objects to create the BGP
sessions and advertises the associated prefixes dynamically. Only
the key information, for example peer IP addresses, peer AS number
are exchanged via the PCEP protocol. Other parameters that are
needed for the BGP session setup should be derived from their default
values, as described in Section 7.2. Upon receives such key
information, the BGP module on the PCC should try to accomplish the
task that appointed by the PCEP protocol and report the status to the
PCEP modules.
There is no influence to current implementation of BGP Finite State
Machine(FSM). The PCEP cares only the success and failure status of
BGP session, and act upon such information accordingly.
The error handling procedures related to incorrect BGP parameters are
specified in Section 6.1, Section 6.2, and Section 6.3. The handling
of the dynamic BGP sessions and associated prefixes on PCE failure is
described in Section 9.
11. New Error-Types and Error-Values Defined
A PCEP-ERROR object is used to report a PCEP error and is
characterized by an Error-Type that specifies that type of error and
an Error-value that provides additional information about the error.
An additional Error-Type and several Error-values are defined to
represent some the errors related to the newly defined objects, which
are related to Native IP TE procedures.
Wang, et al. Expires 11 August 2022 [Page 22]
Internet-Draft PCEP Extension for Native IP Network February 2022
+============+===============+==============================+
| Error-Type | Meaning | Error-value |
+============+===============+=====================================+
| TBD6 | Native IP | |
| | TE failure | |
+------------+---------------+-------------------------------------+
| | | 0: Unassigned |
+------------+---------------+-------------------------------------+
| | |TBD7: Peer AS not match |
+------------+---------------+-------------------------------------+
| | |TBD8:Peer IP can't be reached |
+------------+---------------+-------------------------------------+
| | |TBD9:Local IP is in use |
+------------+---------------+-------------------------------------+
| | |TBD10:Remote IP is in use |
+------------+---------------+-------------------------------------+
| | |TBD11:Exist BGP session broken |
+------------+---------------+-------------------------------------+
| | |TBD12:Explicit Peer Route Error |
+------------+---------------+-------------------------------------+
| | |TBD17:EPR/BPI Peer Info mismatch |
+------------+---------------+-------------------------------------+
| | |TBD18:BPI/PPA Address Family mismatch|
+------------+---------------+-------------------------------------+
| | |TBD19:PPA/BPI Peer Info mismatch |
+------------+---------------+-------------------------------------+
Figure 12: Newly defined Error-Type and Error-Value
12. Deployment Considerations
The information transferred in this draft is mainly used for the
light weight BGP session setup, explicit route deployment and the
prefix distribution. The planning, allocation and distribution of
the peer addresses within IGP should be accomplished in advanced and
they are out of the scope of this draft.
[RFC8232] describes the state synchronization procedure between
stateful PCE and PCC. The communication of PCE and PCC described in
this draft should also follow this procedures, treat the three newly
defined objects that associated with the same symbolic path name as
the attribute of the same path in the LSP-DB.
Wang, et al. Expires 11 August 2022 [Page 23]
Internet-Draft PCEP Extension for Native IP Network February 2022
When PCE detects one or some of the PCCs are out of control, it
should recompute and redeploy the traffic engineering path for native
IP on the active PCCs. When PCC detects that it is out of control of
the PCE, it should clear the information that initiated by the PCE.
The PCE should assures the avoidance of possible transient loop in
such node failure when it deploy the explicit peer route on the PCCs.
If the established BGP session is broken after some time, the PCC
should also report such error via PCErr message with Err-type=TBD6
and error value(Error-value=TBD11, Existing BGP session is broken).
Upon receiving such PCErr message, the PCE should clear the prefixes
advertisement on the previous BGP session, clear the explicit peer
route to the previous peer address; select other Local_IP/Peer_IP
pair to establish the new BGP session, deploy the explicit peer route
to the new peer address, and advertises the prefixes on the new BGP
session.
13. Security Considerations
The setup of BGP sessions, prefix advertisement, and explicit peer
route establishment are all controlled by the PCE. See [RFC4271] and
[RFC4272] for BGP security considerations. Security consideration
part in [RFC5440] and [RFC8231] should be considered. To prevent a
bogus PCE sending harmful messages to the network nodes, the network
devices should authenticate the validity of the PCE and ensure a
secure communication channel between them. Mechanisms described in
[RFC8253] should be used.
14. IANA Considerations
14.1. Path Setup Type Registry
[RFC8408] created a sub-registry within the "Path Computation Element
Protocol (PCEP) Numbers" registry called "PCEP Path Setup Types".
IANA is requested to allocate a new code point within this registry,
as follows:
Value Description Reference
TBD1 Native IP TE Path This document
14.2. PCECC-CAPABILITY sub-TLV's Flag field
[RFC9050] created a sub-registry within the "Path Computation Element
Protocol (PCEP) Numbers" registry to manage the value of the PCECC-
CAPABILITY sub-TLV's 32-bits Flag field. IANA is requested to
allocate a new bit position within this registry, as follows:
Wang, et al. Expires 11 August 2022 [Page 24]
Internet-Draft PCEP Extension for Native IP Network February 2022
Value Description Reference
TBD2(N) NATIVE-IP-TE-CAPABILITY This document
14.3. PCEP Object Types
IANA is requested to allocate new registry for the PCEP Object Type:
Object-Class Value Name Reference
44 CCI Object This document
Object-Type
TBD13: Native IP
TBD14 BGP Peer Info This document
Object-Type
1: IPv4 address
2: IPv6 address
TBD15 Explicit Peer Route This document
Object-Type
1: IPv4 address
2: IPv6 address
TBD16 Peer Prefix Advertisement This document
Object-Type
1: IPv4 address
2: IPv6 address
14.4. PCEP-Error Object
IANA is requested to allocate new error types and error values within
the "PCEP-ERROR Object Error Types and Values" sub-registry of the
PCEP Numbers registry for the following errors::
Wang, et al. Expires 11 August 2022 [Page 25]
Internet-Draft PCEP Extension for Native IP Network February 2022
Error-Type Meaning Error-value Reference
6 Mandatory Object missing
TBD4:Native IP object missing This document
10 Reception of an invalid object
TBD3:PCECC NATIVE-IP-TE-CAPABILITY bit is not set This document
19 Invalid Operation
TBD5:Only one of the BPI,EPR or PPA object can be included in this message This document
TBD6 Native IP TE failure This document
TBD7:Peer AS not match
TBD8:Peer IP can't be reached
TBD9:Local IP is in use
TBD10:Remote IP is in use
TBD11:Exist BGP session broken
TBD12:Explicit Peer Route Error
TBD17:EPR/BPI Peer Info mismatch
TBD18:BPI/PPA Address Family mismatch
TBD19:PPA/BPI Peer Info mismatch
15. Contributor
Dhruv Dhody has contributed the contents of this draft.
16. Acknowledgement
Thanks Mike Koldychev, Susan Hares, Siva Sivabalan, Adam Simpson for
his valuable suggestions and comments.
17. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/info/rfc2119>.
[RFC3209] Awduche, D., Berger, L., Gan, D., Li, T., Srinivasan, V.,
and G. Swallow, "RSVP-TE: Extensions to RSVP for LSP
Tunnels", RFC 3209, DOI 10.17487/RFC3209, December 2001,
<https://www.rfc-editor.org/info/rfc3209>.
[RFC4271] Rekhter, Y., Ed., Li, T., Ed., and S. Hares, Ed., "A
Border Gateway Protocol 4 (BGP-4)", RFC 4271,
DOI 10.17487/RFC4271, January 2006,
<https://www.rfc-editor.org/info/rfc4271>.
Wang, et al. Expires 11 August 2022 [Page 26]
Internet-Draft PCEP Extension for Native IP Network February 2022
[RFC4272] Murphy, S., "BGP Security Vulnerabilities Analysis",
RFC 4272, DOI 10.17487/RFC4272, January 2006,
<https://www.rfc-editor.org/info/rfc4272>.
[RFC5440] Vasseur, JP., Ed. and JL. Le Roux, Ed., "Path Computation
Element (PCE) Communication Protocol (PCEP)", RFC 5440,
DOI 10.17487/RFC5440, March 2009,
<https://www.rfc-editor.org/info/rfc5440>.
[RFC5880] Katz, D. and D. Ward, "Bidirectional Forwarding Detection
(BFD)", RFC 5880, DOI 10.17487/RFC5880, June 2010,
<https://www.rfc-editor.org/info/rfc5880>.
[RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
May 2017, <https://www.rfc-editor.org/info/rfc8174>.
[RFC8231] Crabbe, E., Minei, I., Medved, J., and R. Varga, "Path
Computation Element Communication Protocol (PCEP)
Extensions for Stateful PCE", RFC 8231,
DOI 10.17487/RFC8231, September 2017,
<https://www.rfc-editor.org/info/rfc8231>.
[RFC8232] Crabbe, E., Minei, I., Medved, J., Varga, R., Zhang, X.,
and D. Dhody, "Optimizations of Label Switched Path State
Synchronization Procedures for a Stateful PCE", RFC 8232,
DOI 10.17487/RFC8232, September 2017,
<https://www.rfc-editor.org/info/rfc8232>.
[RFC8253] Lopez, D., Gonzalez de Dios, O., Wu, Q., and D. Dhody,
"PCEPS: Usage of TLS to Provide a Secure Transport for the
Path Computation Element Communication Protocol (PCEP)",
RFC 8253, DOI 10.17487/RFC8253, October 2017,
<https://www.rfc-editor.org/info/rfc8253>.
[RFC8281] Crabbe, E., Minei, I., Sivabalan, S., and R. Varga, "Path
Computation Element Communication Protocol (PCEP)
Extensions for PCE-Initiated LSP Setup in a Stateful PCE
Model", RFC 8281, DOI 10.17487/RFC8281, December 2017,
<https://www.rfc-editor.org/info/rfc8281>.
[RFC8283] Farrel, A., Ed., Zhao, Q., Ed., Li, Z., and C. Zhou, "An
Architecture for Use of PCE and the PCE Communication
Protocol (PCEP) in a Network with Central Control",
RFC 8283, DOI 10.17487/RFC8283, December 2017,
<https://www.rfc-editor.org/info/rfc8283>.
Wang, et al. Expires 11 August 2022 [Page 27]
Internet-Draft PCEP Extension for Native IP Network February 2022
[RFC8408] Sivabalan, S., Tantsura, J., Minei, I., Varga, R., and J.
Hardwick, "Conveying Path Setup Type in PCE Communication
Protocol (PCEP) Messages", RFC 8408, DOI 10.17487/RFC8408,
July 2018, <https://www.rfc-editor.org/info/rfc8408>.
[RFC8697] Minei, I., Crabbe, E., Sivabalan, S., Ananthakrishnan, H.,
Dhody, D., and Y. Tanaka, "Path Computation Element
Communication Protocol (PCEP) Extensions for Establishing
Relationships between Sets of Label Switched Paths
(LSPs)", RFC 8697, DOI 10.17487/RFC8697, January 2020,
<https://www.rfc-editor.org/info/rfc8697>.
[RFC8735] Wang, A., Huang, X., Kou, C., Li, Z., and P. Mi,
"Scenarios and Simulation Results of PCE in a Native IP
Network", RFC 8735, DOI 10.17487/RFC8735, February 2020,
<https://www.rfc-editor.org/info/rfc8735>.
[RFC8821] Wang, A., Khasanov, B., Zhao, Q., and H. Chen, "PCE-Based
Traffic Engineering (TE) in Native IP Networks", RFC 8821,
DOI 10.17487/RFC8821, April 2021,
<https://www.rfc-editor.org/info/rfc8821>.
[RFC9050] Li, Z., Peng, S., Negi, M., Zhao, Q., and C. Zhou, "Path
Computation Element Communication Protocol (PCEP)
Procedures and Extensions for Using the PCE as a Central
Controller (PCECC) of LSPs", RFC 9050,
DOI 10.17487/RFC9050, July 2021,
<https://www.rfc-editor.org/info/rfc9050>.
Authors' Addresses
Aijun Wang
China Telecom
Beiqijia Town, Changping District
Beijing
Beijing, 102209
China
Email: wangaj3@chinatelecom.cn
Boris Khasanov
Yandex LLC
Ulitsa Lva Tolstogo 16
Moscow
Email: bhassanov@yahoo.com
Wang, et al. Expires 11 August 2022 [Page 28]
Internet-Draft PCEP Extension for Native IP Network February 2022
Sheng Fang
Huawei Technologies,Co.,Ltd
Huawei Bld., No.156 Beiqing Rd.
Beijing
China
Email: fsheng@huawei.com
Ren Tan
Huawei Technologies,Co.,Ltd
Huawei Bld., No.156 Beiqing Rd.
Beijing
China
Email: tanren@huawei.com
Chun Zhu
ZTE Corporation
50 Software Avenue, Yuhua District
Nanjing
Jiangsu, 210012
China
Email: zhu.chun1@zte.com.cn
Wang, et al. Expires 11 August 2022 [Page 29]