Skip to main content

The PKCS#11 URI Scheme
draft-pechanec-pkcs11uri-13

The information below is for an old version of the document.
Document Type
This is an older version of an Internet-Draft that was ultimately published as RFC 7512.
Expired & archived
Authors Jan Pechanec , Darren Moffat
Last updated 2014-04-02 (Latest revision 2013-09-29)
RFC stream (None)
Formats
Reviews
Stream Stream state (No stream defined)
Consensus boilerplate Unknown
RFC Editor Note (None)
IESG IESG state Became RFC 7512 (Proposed Standard)
Telechat date (None)
Responsible AD (None)
Send notices to (None)
draft-pechanec-pkcs11uri-13
Network Working Group                                        J. Pechanec
Internet-Draft                                                 D. Moffat
Intended status: Standards Track                      Oracle Corporation
Expires: April 03, 2014                               September 30, 2013

                         The PKCS#11 URI Scheme
                      draft-pechanec-pkcs11uri-13

Abstract

   This memo specifies a PKCS#11 Uniform Resource Identifier (URI)
   Scheme for identifying PKCS#11 objects stored in PKCS#11 tokens, for
   identifying PKCS#11 tokens themselves, or for identifying PKCS#11
   libraries.  The URI is based on how PKCS#11 objects, tokens, and
   libraries are identified in the PKCS#11 Cryptographic Token Interface
   Standard.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at http://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on April 03, 2014.

Copyright Notice

   Copyright (c) 2013 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

Pechanec & Moffat        Expires April 03, 2014                 [Page 1]
Internet-Draft           The PKCS#11 URI Scheme           September 2013

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   2
   2.  Contributors  . . . . . . . . . . . . . . . . . . . . . . . .   3
   3.  PKCS#11 URI Scheme Definition . . . . . . . . . . . . . . . .   3
     3.1.  PKCS#11 URI Scheme Name . . . . . . . . . . . . . . . . .   4
     3.2.  PKCS#11 URI Scheme Status . . . . . . . . . . . . . . . .   4
     3.3.  PKCS#11 URI Scheme Syntax . . . . . . . . . . . . . . . .   4
     3.4.  PKCS#11 URI Matching Guidelines . . . . . . . . . . . . .   7
     3.5.  PKCS#11 URI Comparison  . . . . . . . . . . . . . . . . .   8
   4.  Examples of PKCS#11 URIs  . . . . . . . . . . . . . . . . . .   9
   5.  IANA Considerations . . . . . . . . . . . . . . . . . . . . .  11
   6.  Security Considerations . . . . . . . . . . . . . . . . . . .  11
   7.  References  . . . . . . . . . . . . . . . . . . . . . . . . .  12
     7.1.  Normative References  . . . . . . . . . . . . . . . . . .  12
     7.2.  Informative References  . . . . . . . . . . . . . . . . .  12
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  12

1.  Introduction

   The PKCS #11: Cryptographic Token Interface Standard [pkcs11_spec]
   specifies an API, called Cryptoki, for devices which hold
   cryptographic information and perform cryptographic functions.
   Cryptoki, pronounced crypto-key and short for cryptographic token
   interface, follows a simple object-based approach, addressing the
   goals of technology independence (any kind of device may be used) and
   resource sharing (multiple applications may access multiple devices),
   presenting applications with a common, logical view of the device - a
   cryptographic token.

   It is desirable for applications or libraries that work with PKCS#11
   tokens to accept a common identifier that consumers could use to
   identify an existing PKCS#11 storage object in a PKCS#11 token, an
   existing token itself, or an existing Cryptoki library (also called a
   producer, module, or provider).  The set of storage object types that
   can be stored in a PKCS#11 token includes a certificate, a public,
   private or secret key, and a data object.  These objects can be
   uniquely identifiable via the PKCS#11 URI scheme defined in this

Pechanec & Moffat        Expires April 03, 2014                 [Page 2]
Internet-Draft           The PKCS#11 URI Scheme           September 2013

   document.  The set of attributes describing a storage object can
   contain an object label, its type, and its ID.  The set of attributes
   that identifies a PKCS#11 token can contain a token label, a
   manufacturer name, a serial number, and a token model.  Attributes
   that can identify a Cryptoki library are a library manufacturer, a
   library description, and a library version.  Library attributes may
   be necessary to use if more than one Cryptoki library provides a
   token and/or PKCS#11 objects of the same name(s).

   The PKCS#11 URI cannot identify other objects aside from storage
   objects, for example a hardware feature or mechanism.  Note that a
   Cryptoki library does not have to provide for storage objects at all.
   The URI can still be used to identify a specific PKCS#11 token or an
   API producer in such a case.

   A subset of existing PKCS#11 structure members and object attributes
   was chosen believed to be sufficient in uniquely identifying a
   PKCS#11 token, storage object, or library in a configuration file, on
   a command line, or in a configuration property of something else.
   Should there be a need for a more complex information exchange on
   PKCS#11 entities a different means of data marshalling should be
   chosen accordingly.

   A PKCS#11 URI is not intended to be used to create new PKCS#11
   objects in tokens, or to create PKCS#11 tokens.  It is solely to be
   used to identify and work with existing storage objects and tokens
   through the PKCS#11 API, or identify Cryptoki libraries themselves.

   The URI scheme defined in this document is designed specifically with
   a mapping to the PKCS#11 API in mind.  The URI uses the scheme, path
   and query components defined in the Uniform Resource Identifier
   (URI): Generic Syntax [RFC3986] document.  The URI does not use the
   hierarchical element for a naming authority in the path since the
   authority part could not be mapped to PKCS#11 API elements.  The URI
   does not use the fragment component.

   If an application has no access to a producer or producers of the
   PKCS#11 API it is left to its implementation to provide adequate user
   interface to locate and load such producer(s).

2.  Contributors

   Stef Walter, Nikos Mavrogiannopoulos, Nico Williams, Dan Winship, and
   Jaroslav Imrich contributed to the development of this document.

3.  PKCS#11 URI Scheme Definition

Pechanec & Moffat        Expires April 03, 2014                 [Page 3]
Internet-Draft           The PKCS#11 URI Scheme           September 2013

   In accordance with [RFC4395], this section provides the information
   required to register the PKCS#11 URI scheme.

3.1.  PKCS#11 URI Scheme Name

   pkcs11

3.2.  PKCS#11 URI Scheme Status

   Permanent.

3.3.  PKCS#11 URI Scheme Syntax

   The PKCS#11 URI is a sequence of attribute value pairs separated by a
   semicolon that form a one level path component, optionally followed
   by a query.  In accordance with Section 2.5 of [RFC3986], the data
   should first be encoded as octets according to the UTF-8 character
   encoding [RFC3629]; then only those octets that do not correspond to
   characters in the unreserved set or to permitted characters from the
   reserved set should be percent-encoded.  This specification suggests
   one allowable exception to that rule for the "id" attribute, as
   stated later in this section.  Grammar rules "unreserved" and "pct-
   encoded" in the PKCS#11 URI specification below are imported from
   [RFC3986].  As a special case, note that according to Appendix A of
   [RFC3986], a space must be percent-encoded.

   PKCS#11 specification imposes various limitations on the value of
   attributes, be it a more restrictive character set for the "serial"
   attribute or fixed sized buffers for almost all the others, including
   "token", "manufacturer", and "model" attributes.  However, the
   PKCS#11 URI notation does not impose such limitations aside from
   removing generic and PKCS#11 URI delimiters from a permitted
   character set.  We believe that being too restrictive on the
   attribute values could limit the PKCS#11 URI's usefulness.  What is
   more, possible future changes to the PKCS#11 specification should not
   affect existing attributes.

   A PKCS#11 URI takes the form (for explanation of Augmented BNF, see
   [RFC5234]):

Pechanec & Moffat        Expires April 03, 2014                 [Page 4]
Internet-Draft           The PKCS#11 URI Scheme           September 2013

   pk11-URI            = "pkcs11" ":" pk11-path *1("?" pk11-query)
   ; Path component and its attributes.  Path may be empty.
   pk11-path           = *1(pk11-pattr *(";" pk11-pattr))
   pk11-pattr          = pk11-token / pk11-manuf / pk11-serial /
                         pk11-model / pk11-lib-manuf /
                         pk11-lib-ver / pk11-lib-desc /
                         pk11-object / pk11-type / pk11-id /
                         pk11-x-pattr
   ; Query component and its attributes.  Query may be empty.
   pk11-qattr          = pk11-pin-source / pk11-x-qattr
   pk11-query          = *1(pk11-qattr *("&" pk11-qattr))
   ; RFC 3986 section 2.2 mandates all potentially reserved characters
   ; that do not conflict with actual delimiters of the URI do not have
   ; to be percent-encoded.
   pk11-res-avail =      ":" / "[" / "]" / "@" / "!" / "$" /
                         "'" / "(" / ")" / "*" / "+" / "," / "="
   pk11-path-res-avail = pk11-res-avail / "&"
   ; We allow "/" and "?" in the query to be unencoded but "&" must
   ; be encoded since it may be used as a delimiter in the component.
   pk11-query-res-avail = pk11-res-avail / "/" / "?"
   pk11-pchar          = unreserved / pk11-path-res-avail / pct-encoded
   pk11-qchar          = unreserved / pk11-query-res-avail / pct-encoded
   pk11-token          = "token" "=" *pk11-pchar
   pk11-manuf          = "manufacturer" "=" *pk11-pchar
   pk11-serial         = "serial" "=" *pk11-pchar
   pk11-model          = "model" "=" *pk11-pchar
   pk11-lib-manuf      = "library-manufacturer" "=" *pk11-pchar
   pk11-lib-desc       = "library-description" "=" *pk11-pchar
   pk11-lib-ver        = "library-version" "=" 1*DIGIT *1("." 1*DIGIT)
   pk11-object         = "object" "=" *pk11-pchar
   pk11-type           = "type" "=" *1("public" / "private" / "cert" /
                         "secret-key" / "data")
   pk11-id             = "id" "=" *pk11-pchar
   pk11-pin-source     = "pin-source" "=" *pk11-qchar
   pk11-x-attr-nm-char = ALPHA / DIGIT / "-" / "_"
   ; Permitted value of a vendor specific attribute is based on
   ; whether the attribute is used in the path or in the query.
   pk11-x-pattr         = "x-" 1*pk11-x-attr-nm-char "=" *pk11-pchar
   pk11-x-qattr         = "x-" 1*pk11-x-attr-nm-char "=" *pk11-qchar

Pechanec & Moffat        Expires April 03, 2014                 [Page 5]
Internet-Draft           The PKCS#11 URI Scheme           September 2013

   The URI path component contains attributes that identify a resource
   in a one level hierarchy provided by Cryptoki producers.  The query
   component may contain a PIN source attribute that may be needed to
   retrieve the resource identified by the URI path.  Both path and
   query components may contain vendor specific attributes.  Such
   attribute names must start with an "x-" prefix.  Attributes in the
   path component are delimited by ';' character, attributes in the
   query component use '&' as a delimiter.

   The general '/' delimiter was removed from available characters that
   do not have to be percent-encoded in the path component so that
   generic URI parsers never split the path component into multiple
   segments.  The '/' delimiter can be used unencoded in the query
   component.  Delimiter '?' was removed since the PKCS#11 URI uses a
   query component.  Delimiter '#' was removed so that generic URI
   parsers are not confused by unencoded hash characters.  All other
   generic delimiters are allowed to be used unencoded (':', '[', ']',
   and '@') in the PKCS#11 URI.

   The attribute "token" represents a token label and corresponds to the
   "label" member of the CK_TOKEN_INFO structure, the attribute
   "manufacturer" corresponds to the "manufacturerID" member of
   CK_TOKEN_INFO, the attribute "serial" corresponds to the
   "serialNumber" member of CK_TOKEN_INFO, the attribute "model"
   corresponds to the "model" member of CK_TOKEN_INFO, the attribute
   "library-manufacturer" represents the Cryptoki library manufacturer
   and corresponds to the "manufacturerID" member of the CK_INFO
   structure, the attribute "library-description" corresponds to the
   "libraryDescription" member of CK_INFO, the attribute "library-
   version" corresponds to the "libraryVersion" member of CK_INFO, the
   attribute "object" represents a PKCS#11 object label and corresponds
   to the "CKA_LABEL" object attribute, the attribute "type" represents
   the type of the object and corresponds to the "CKA_CLASS" object
   attribute, the attribute "id" represents the object ID and
   corresponds to the "CKA_ID" object attribute, and the attribute "pin-
   source" specifies where the application or library should find the
   token PIN, if needed.

   The PKCS#11 URI must not contain duplicate attributes of the same
   name in the URI path component.  It means that each attribute may be
   present at most once in the PKCS#11 URI path.  Aside from the "pin-
   source" attribute, duplicate attributes may be present in the URI
   query component and it is up to the URI consumer to decide on how to
   deal with such duplicates.

   The "pin-source" attribute may represent a filename that contains a
   token PIN but an application may overload this attribute.  For
   example, "pin-source=%7Cprog-name" could mean to read a PIN from an

Pechanec & Moffat        Expires April 03, 2014                 [Page 6]
Internet-Draft           The PKCS#11 URI Scheme           September 2013

   external application (%7C denotes a pipe '|' character).  Note that
   an application may always ask for a PIN and/or interpret the "pin-
   source" attribute by any means it decides to.  However, as discussed
   in Section 6, the attribute should never contain the PIN itself.

   It is recommended to percent-encode the whole value of the "id"
   attribute which is supposed to be handled as arbitrary binary data.
   Value "M" of the "library-version" attribute should be interpreted as
   "M" for the major and "0" for the minor version of the library.  Note
   that if the "library-version" attribute is present, the major version
   number is mandatory.

   An empty PKCS#11 URI path attribute that does allow for an empty
   value matches a corresponding structure member or an object attribute
   with an empty value.  Note that according to the PKCS#11
   specification [pkcs11_spec], empty character values in a PKCS#11 API
   producer must be padded with spaces and should not be NULL
   terminated.

3.4.  PKCS#11 URI Matching Guidelines

   The PKCS#11 URI can identify PKCS#11 storage objects, tokens, or
   Cryptoki libraries.  The following guidelines should help a PKCS#11
   URI consumer (eg. an application accepting PKCS#11 URIs) to match the
   URI with the desired resource.

   o  the consumer must know whether the URI is to identify PKCS#11
      storage object(s), token(s), or Cryptoki producer(s).

   o  an unrecognized attribute in the URI path component, including a
      vendor specific attribute, should result in an empty set of
      matched resources.  The consumer should consider whether an error
      message presented to the user is appropriate in such a case.

   o  an unrecognized attribute in the URI query should be ignored.  The
      consumer should consider whether a warning message presented to
      the user is appropriate in such a case.

   o  an attribute not present in the URI path but known to a consumer
      matches everything.  Each additional attribute present in the URI
      path further restricts the selection.

   o  a logical extension of the above is that an empty URI path matches
      everything.  For example, if used to identify storage objects, it
      matches all accessible objects in all tokens provided by all
      PKCS#11 API producers found in the system.

Pechanec & Moffat        Expires April 03, 2014                 [Page 7]
Internet-Draft           The PKCS#11 URI Scheme           September 2013

   o  use of the PIN attribute may change the set of storage objects
      visible to the consumer.

   o  in addition to the PIN attribute, query string attributes may
      contain further information about how to perform the selection or
      other related information.

3.5.  PKCS#11 URI Comparison

   Comparison of two URIs is a way of determining whether the URIs are
   equivalent without comparing the actual resource the URIs point to.
   The comparison of URIs aims to minimize false negatives while
   strictly avoiding false positives.

   Two PKCS#11 URIs are said to be equal if URIs as character strings
   are identical as specified in Section 6.2.1 of [RFC3986], or if both
   following rules are fulfilled:

   o  set of attributes present in the URI is equal.  Note that the
      ordering of attributes in the URI string is not significant for
      the mechanism of comparison.

   o  values of respective attributes are equal based on rules specified
      below

   The rules for comparing values of respective attributes are:

   o  values of attributes "library-description", "library-
      manufacturer", "manufacturer", "model", "object", "serial",
      "token", and "type" must be compared using a simple string
      comparison as specified in Section 6.2.1 of [RFC3986] after the
      case and the percent-encoding normalization are both applied as
      specified in Section 6.2.2 of [RFC3986]

   o  value of attribute "id" must be compared using the simple string
      comparison after all bytes are percent-encoded using uppercase
      letters for digits A-F

   o  value for attribute "pin-source", if deemed containing the
      filename with the PIN value, must be compared using the simple
      string comparison after the full syntax based normalization as
      specified in Section 6.2.2 of [RFC3986] is applied.  If value of
      the "pin-source" attribute is believed to be overloaded it is
      recommended to perform case and percent-encoding normalization
      before the values are compared but the exact mechanism of
      comparison is left to the application.

Pechanec & Moffat        Expires April 03, 2014                 [Page 8]
Internet-Draft           The PKCS#11 URI Scheme           September 2013

   o  value of attribute "library-version" must be processed as a
      specific scheme-based normalization permitted by Section 6.2.3 of
      [RFC3986].  The value must be split into a major and minor version
      with character '.' (dot) serving as a delimiter.  Library version
      "M" must be treated as "M" for the major version and "0" for the
      minor version.  Resulting minor and major version numbers must be
      then separately compared numerically.

   o  when comparing vendor specific attributes it is recommended to
      perform case and percent-encoding normalization before the values
      are compared but the exact mechanism of comparison is left to the
      application.

4.  Examples of PKCS#11 URIs

   This section contains some examples of how PKCS#11 token objects,
   PKCS#11 tokens, and PKCS#11 libraries can be identified using the
   PKCS#11 URI scheme.  Note that in some of the following examples,
   newlines and spaces were inserted for better readability.  As
   specified in Appendix C of [RFC3986], whitespace should be ignored
   when extracting the URI.  Also note that all spaces as part of the
   URI are percent-encoded, as specified in Appendix A of [RFC3986].

   An empty PKCS#11 URI might be useful to PKCS#11 consumers:

   pkcs11:

   One of the simplest and most useful forms might be a PKCS#11 URI that
   specifies only an object label and its type.  The default token is
   used so the URI does not specify it.  Note that when specifying
   public objects, a token PIN might not be required.

   pkcs11:object=my-pubkey;type=public

   When a private key is specified either the "pin-source" attribute or
   an application specific method would be usually used.  Note that '/'
   is not percent-encoded in the "pin-source" attribute value since this
   attribute is part of the query component, not the path, and thus is
   separated by '?' from the rest of the URI.

   pkcs11:object=my-key;type=private?pin-source=/etc/token

   The following example identifies a certificate in the software token.
   Note an empty value for the attribute "serial".  Also note that the
   "id" attribute value is entirely percent-encoded, as recommended.

Pechanec & Moffat        Expires April 03, 2014                 [Page 9]
Internet-Draft           The PKCS#11 URI Scheme           September 2013

   While ',' is in the reserved set it does not have to be percent-
   encoded since it does not conflict with any sub-delimiters used.  The
   '#' character as in "The Software PKCS#11 Softtoken" must be percent-
   encoded.

   pkcs11:token=The%20Software%20PKCS%2311%20Softtoken;
          manufacturer=Snake%20Oil,%20Inc.;
          model=1.0;
          object=my-certificate;
          type=cert;
          id=%69%95%3E%5C%F4%BD%EC%91;
          serial=
          ?pin-source=/etc/token_pin

   The token alone can be identified without specifying any PKCS#11
   objects.  A PIN may still be needed to list all objects, for example.

   pkcs11:token=Software%20PKCS%2311%20softtoken;
          manufacturer=Snake%20Oil,%20Inc.
          ?pin-source=/etc/token_pin

   The Cryptoki library alone can be also identified without specifying
   a PKCS#11 token or object.

   pkcs11:library-manufacturer=Snake%20Oil,%20Inc.;
          library-description=Soft%20Token%20Library;
          library-version=1.23

   The following example shows that the attribute value can contain a
   semicolon.  In such case, it is percent-encoded.  The token attribute
   value must be read as "My token; created by Joe".  Lower case letters
   can also be used in percent-encoding as shown below in the "id"
   attribute value but note that Sections 2.1 and 6.2.2.1 of [RFC3986]
   read that all percent-encoded characters should use the uppercase
   hexadecimal digits.  More specifically, if the URI string was to be
   compared, the algorithm defined in Section 3.5 explicitly requires
   percent-encoding to use the uppercase digits A-F in the "id"
   attribute values.  And as explained in Section 3.3, library version
   "3" should be interpreted as "3" for the major and "0" for the minor
   version of the library.

   pkcs11:token=My%20token%25%20created%20by%20Joe;
          library-version=3;
          id=%01%02%03%Ba%dd%Ca%fe%04%05%06

Pechanec & Moffat        Expires April 03, 2014                [Page 10]
Internet-Draft           The PKCS#11 URI Scheme           September 2013

   If there is any need to include literal "%;" substring, for example,
   both characters must be escaped.  The token value must be read as "A
   name with a substring %;".

   pkcs11:token=A%20name%20with%20a%20substring%20%25%3B;
          object=my-certificate;
          type=cert
          ?pin-source=/etc/token_pin

   The next example includes a small A with acute in the token name.  It
   must be encoded in octets according to the UTF-8 character encoding
   and then percent-encoded.  Given that a small A with acute is U+225
   unicode code point, the UTF-8 encoding is 195 161 in decimal, and
   that is "%C3%A1" in percent-encoding.

   pkcs11:token=Name%20with%20a%20small%20A%20with%20acute:%20%C3%A1;
          object=my-certificate;
          type=cert

   Both the path and query components may contain vendor specific
   attributes.  Attributes in the query component may be delimited by
   either ';' or '&'.  We use '&' in the example that follows.

   pkcs11:token=my-token;
          object=my-certificate;
          type=cert;
          x-vend-aaa=value-a
          ?pin-source=/etc/token_pin&
          x-vend-bbb=value-b

5.  IANA Considerations

   This document moves the "pkcs11" URI scheme from the provisional to
   the permanent URI scheme registry.  The registration template for the
   URI scheme is accessible on http://www.iana.org/assignments/uri-
   schemes.

6.  Security Considerations

   There are general security considerations for URI schemes discussed
   in Section 7 of [RFC3986].

   From those security considerations, Section 7.1 of [RFC3986] applies
   since there is no guarantee that the same PKCS#11 URI will always
   identify the same object, token, or a library in the future.

Pechanec & Moffat        Expires April 03, 2014                [Page 11]
Internet-Draft           The PKCS#11 URI Scheme           September 2013

   Section 7.5 of [RFC3986] applies since the PKCS#11 URI may be used in
   command line arguments to run applications, and those arguments can
   be world readable on some systems.  For that reasons, the URI
   intentionally does not allow for specifying the PKCS#11 token PIN as
   a URI attribute.

7.  References

7.1.  Normative References

   [RFC3629]  Yergeau, F., "UTF-8, a transformation format of ISO
              10646", RFC 3629, STD 63, November 2003.

   [RFC3986]  Berners-Lee, T., Fielding, R., and L. Masinter, "Uniform
              Resource Identifier (URI): Generic Syntax", RFC 3986, STD
              66, January 2005.

   [RFC5234]  Crocker, D. and P. Overell, "Augmented BNF for Syntax
              Specifications: ABNF", RFC 5234, STD 68, January 2008.

7.2.  Informative References

   [RFC4395]  Hansen, T., Hardie, T., and L. Masinter, "Guidelines and
              Registration Procedures for New URI Schemes", RFC 4395,
              February 2006.

   [pkcs11_spec]
              RSA Laboratories, "PKCS #11: Cryptographic Token Interface
              Standard v2.20", June 2004.

Authors' Addresses

   Jan Pechanec
   Oracle Corporation
   4180 Network Circle
   Santa Clara  CA 95054
   USA

   Email: Jan.Pechanec@Oracle.COM
   URI:   http://www.oracle.com

Pechanec & Moffat        Expires April 03, 2014                [Page 12]
Internet-Draft           The PKCS#11 URI Scheme           September 2013

   Darren J. Moffat
   Oracle Corporation
   Oracle Parkway
   Thames Valley Park
   Reading  RG6 1RA
   UK

   Email: Darren.Moffat@Oracle.COM
   URI:   http://www.oracle.com

Pechanec & Moffat        Expires April 03, 2014                [Page 13]