Context Label for MPLS EVPN
draft-wang-bess-evpn-context-label-03
The information below is for an old version of the document.
| Document | Type |
This is an older version of an Internet-Draft whose latest revision state is "Expired".
|
|
|---|---|---|---|
| Authors | Yubao(Bob) Wang , Bing Song | ||
| Last updated | 2020-08-15 (Latest revision 2020-06-10) | ||
| RFC stream | (None) | ||
| Formats | |||
| Stream | Stream state | (No stream defined) | |
| Consensus boilerplate | Unknown | ||
| RFC Editor Note | (None) | ||
| IESG | IESG state | I-D Exists | |
| Telechat date | (None) | ||
| Responsible AD | (None) | ||
| Send notices to | (None) |
draft-wang-bess-evpn-context-label-03
BESS WG Y. Wang
Internet-Draft B. Song
Intended status: Standards Track ZTE Corporation
Expires: 16 February 2021 15 August 2020
Context Label for MPLS EVPN
draft-wang-bess-evpn-context-label-03
Abstract
EVPN is designed to provide a better VPLS service than [RFC4761] and
[RFC4762], and EVPN indeed introduced many new features which
couldn't be achieved in those old VPLS implementions. But EVPN
didn't inherit all features of old VPLS, and a few issues arises for
EVPN only.
Some of these issues can be imputed to the MP2P nature of EVPN
labels. The PW label in old VPLS is a label for P2P VC, so it
contains more context than a identifier in dataplane for it's VSI
instance.But the EVPN label just identifies it's VSI instnace and it
can't stand for the ingress PE in dataplane. So the following issues
arises with MPLS EVPN service:
* MPLS EVPN statistics can't be done per ingress PE.
* MPLS EVPN can't support hub/spoke use case which the spoke PE can
only connect to each other by the hub PE.
* MPLS EVPN can't support AR REPLICATOR.
* MPLS EVPN can't support anycast SR-MPLS tunnel on the SPE nodes.
This document introduces a compound label stack to take advantage of
both P2P VC and MP2P evpn labels.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Wang & Song Expires 16 February 2021 [Page 1]
Internet-Draft EVPN Context Label August 2020
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on 16 February 2021.
Copyright Notice
Copyright (c) 2020 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents (https://trustee.ietf.org/
license-info) in effect on the date of publication of this document.
Please review these documents carefully, as they describe your rights
and restrictions with respect to this document. Code Components
extracted from this document must include Simplified BSD License text
as described in Section 4.e of the Trust Legal Provisions and are
provided without warranty as described in the Simplified BSD License.
Table of Contents
1. Terminology and Acronyms . . . . . . . . . . . . . . . . . . 3
2. Problem Statement . . . . . . . . . . . . . . . . . . . . . . 5
3. Using VC Label to Add Context Data to EVPN Flows . . . . . . 5
3.1. The Shared Context VCs . . . . . . . . . . . . . . . . . 6
3.2. The per-EVI Context VCs . . . . . . . . . . . . . . . . . 6
4. Context VC Signalling Procedures . . . . . . . . . . . . . . 6
4.1. Construct Leaf A-D Route for IR . . . . . . . . . . . . . 6
4.1.1. Advertising Per-platform VC Label . . . . . . . . . . 7
4.1.2. Advertising Context-Specific VC label . . . . . . . . 7
4.1.3. CSL-Entry Extended Community . . . . . . . . . . . . 8
4.2. The Sharing of Context VCs . . . . . . . . . . . . . . . 9
4.2.1. Using Admin-EVI . . . . . . . . . . . . . . . . . . . 9
4.2.2. Using per-platform VC labels . . . . . . . . . . . . 9
4.3. Establish Ingress Replication List by Leaf A-D Route . . 10
4.4. Backward Compatibility . . . . . . . . . . . . . . . . . 10
5. Solutions . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.1. Solution for Source-Squelching in Hub-Spoke Scenarios . . 11
5.2. Solution for per ingress statistics . . . . . . . . . . . 12
5.3. Solution for AR REPLICATOR in MPLS EVPN . . . . . . . . . 12
5.4. Solution for anycast tunnel usage on SPE . . . . . . . . 13
5.4.1. Control-plane . . . . . . . . . . . . . . . . . . . . 13
5.4.2. Data-plane . . . . . . . . . . . . . . . . . . . . . 14
5.4.3. Dynamical VCL Allocation and Advertisement . . . . . 15
6. Security Considerations . . . . . . . . . . . . . . . . . . . 15
7. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 15
Wang & Song Expires 16 February 2021 [Page 2]
Internet-Draft EVPN Context Label August 2020
8. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 15
9. References . . . . . . . . . . . . . . . . . . . . . . . . . 15
9.1. Normative References . . . . . . . . . . . . . . . . . . 15
9.2. Informative References . . . . . . . . . . . . . . . . . 16
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 16
1. Terminology and Acronyms
This document uses the following acronyms and terms:
BUM - Broadcast, Unknown unicast, and Multicast.
CE - Customer Edge equipment.
PE - Provider Edge equipment.
OPE - Originating PE - the original Router of an EVPN route.
ORIP - Originating Router's IP address.
Root ORIP - The ORIP in the Route Key field of a Leaf A-D route is
called as that Leaf A-D route's Root ORIP. The Route Key field is
the "Route Type specific" field of an PMSI route for which that
Leaf A-D route is generated. When that PMSI route is an IMET
route, that Leaf A-D route's root ORIP is that IMET route's
"Originating Router's IP Address".
Leaf ORIP - The "Originator's Addr" field of the "Route Type
specific" field of a Leaf A-D route is called as that Leaf A-D
route's Leaf ORIP.
Self ORIP - The Leaf ORIP of a Leaf A-D route is also called as
that Leaf A-D route's "self ORIP".
PTA - PMSI Tunnel Attribute.
PTA label - The MPLS label field of PMSI Tunnel Attribute.
PTA flags - The flags field of PMSI Tunnel Attribute.
IR - Ingress Replication.
AR - Assisted Replication.
IR PTA - PMSI Tunnel Attribute with tunnel-type = IR.
AR PTA - PMSI Tunnel Attribute with tunnel-type = AR.
Wang & Song Expires 16 February 2021 [Page 3]
Internet-Draft EVPN Context Label August 2020
IRL - Ingress Replication List, the list for Ingress-Replication
BUM packets forwarding.
LS - Label Space.
CL - Context-identifying Label, or Context Label, A "context
label" is one label that identifies a label table in which the
label immediately below the context label should be looked up. It
is defined in [RFC5331] section 3.
CLS - Context Label Space, a Label Space that is identified by a
Context Label. In [RFC5331], it is called as "Context-specific
Label Space".
CLS ID - Context Label Space ID, which is defined in
[I-D.ietf-bess-mvpn-evpn-aggregation-label].
CSL - Context-Specific Label, a MPLS label that is allocated in a
Context Label Space (CLS) which is identified by a CL. Note that
a CSL is totally different from a CL. A CL itself is typically
allocated in the per-platform label space.
CSL-Entry - Context-Specific Label Entry, a specific MPLS label
allocated in a specific Context Label Space (CLS).
EVI - EVPN Instance.
EVL - EVI label, a MPLS label identifies an EVPN Instance (EVI) or
a MAC/IP/Prefix in that EVPN instance.
EVPN label - The MPLS label in an EVPN route. It includes ESI
label and EVL.
Admin EVI - A EVPN Instance (EVI) that is responsible for specific
signalling work for other EVIs.
EC - Extended Community
SR-TL - Segment Routing (SR) Tunnel Label (TL).
ILM - Incoming Label Map, which is defined in [RFC3031] section
3.11.
CLS ILM - CLS-Specific ILM, an ILM that is installed in a
"Context-specific Label Space".
Transit LSP - A LSP whose label operation for its ILM label is
Label Swapping.
Wang & Song Expires 16 February 2021 [Page 4]
Internet-Draft EVPN Context Label August 2020
2. Problem Statement
EVPN is designed to provide a better VPLS service than RFC4761/
RFC4762, and EVPN indeed introduced many new features which couldn't
be achieved in those old VPLS implemention.But EVPN didn't inherit
all features of old VPLS, and a few issues arises for EVPN only.
Some of these issues can be imputed to the MP2P nature of EVPN
labels. The PW label in old VPLS is a label for P2P VC, so it
contains more context than a identifier in dataplane for it's VSI
instance. But the EVPN label just identifies it's VSI instnace and
it can't stand for the ingress PE in dataplane. So the following
issues arises with MPLS EVPN service:
* MPLS EVPN statistics can't be done per ingress PE. All flows from
remote PEs share the same statistics on egress PE, because they
share the same EVPN label and the egress PE can't pick them out in
the dataplane.
* MPLS EVPN can't support hub/spoke usecase, where the spoke PEs can
only connect to each other through the hub PE. Especially when at
least two of the spoke PEs are connected to a common route
reflector.
* MPLS EVPN can't work as an AR-REPLICATOR. Because the AR-
REPLICATOR will apply replication for the ingress AR-LEAF too.
But a packet shoud not be sent back to the AR-LEAF where it is
received from.
* MPLS EVPN SPE cannot make use of SR-MPLS anycast tunnel because
the two SPEs of the anycast tunnel will assign different EVPN
labels for the same EVPN route.
So this document introduces an compound label stack to take advantage
of both P2P VC and MP2P EVPN labels.
3. Using VC Label to Add Context Data to EVPN Flows
In order to add as much context as old VPLS to EVPN data packet, We
can construct a infrastructure by a full-mesh of context-VCs among
the EVPN PEs.
Take the context-VCs between PE-i and PE-j as an example, VC-ij is
the context-VC from PE-i to PE-j, and VC-ji is the context-VC from
PE-j to PE-i. The VC-ij identifies the PE-i node on PE-j. The VC-ji
identifies PE-j node on PE-i. The VC-label for VC-ij is called as
L-ij, and the VC-label for VC-ji is called as L-ji.
Wang & Song Expires 16 February 2021 [Page 5]
Internet-Draft EVPN Context Label August 2020
So the PE-i can push the L-ij onto the EVPN data packet for PE-j to
distinguish the packet of PE-i from other data packets. Because the
L-ij identifies the ingress PE of the data packet.
There are two styles of context-VC in this draft. One style is named
as shared context-VC, the other style is named as per-EVI context VC.
3.1. The Shared Context VCs
The shared context-VCs are dedicated to identify the context for a
data packet while the EVPN label still identifies the EVPN instance.
Note that typically a shared context VC can be shared by all the EVPN
instances between it's ingress PE and egress PE. In other words, we
don't have to establish a dedicated mesh of context VCs for each
specified EVPN service. So we called the shared context VCs as a
common infrastructure for those EVPN services.
3.2. The per-EVI Context VCs
The per-EVI context VCs are used to identify both the context
(typically the ingress-PE) and the EVPN instance for a data packet at
the same time. In other words, we have to establish a dedicated set
of per-EVI context VCs for each specified EVPN service.
4. Context VC Signalling Procedures
The IMET route per [RFC7432] have a corresponding route-type in MVPN.
It is, in effect, the Intra-AS I-PMSI route per [RFC6514]. The
difference between them is that an IMET route won't handle a
responding Leaf A-D route, but an Intra-AS I-PMSI route will.
The Leaf A-D route per [I-D.ietf-bess-evpn-bum-procedure-updates] is
required for per-EVI context VCs. In this draft, we use the Leaf A-D
route with IR-PTA to establish per-EVI context-VCs. The Leaf A-D
route is generated for an IMET route.
It is an update for [RFC7432]. The backward compatibility will be
described in Section 4.4.
4.1. Construct Leaf A-D Route for IR
PE1 will construct a Leaf A-D route with IR-PTA for EVI1 in response
to an IMET route R1 with IR-PTA. The IMET route R1 is received from
PE2 previously. The key fields of the IMET route is included in the
"Route Key" field of the Leaf A-D route (say R2) along with the ORIP
of PE1 itself. We call the ORIP of PE1 itself as the Leaf A-D
route's "self-ORIP" in order to distinguish it from the Leaf A-D
Wang & Song Expires 16 February 2021 [Page 6]
Internet-Draft EVPN Context Label August 2020
route's Root-ORIP. So the "Route Type sepcific" field of the Leaf
A-D route is per <EVI1, PE2> basis.
4.1.1. Advertising Per-platform VC Label
The MPLS label field in the IR-PTA of the Leaf A-D route is allocated
per <EVI1, PE2> basis in per-platform label space on PE1. So the
per-EVI context VC can identify the EVI1 too.
Note that PE1 may already advertise an IMET route R3 to PE2 before
the advertisement of above Leaf A-D route.
4.1.2. Advertising Context-Specific VC label
Note that the per <EVI,Ingress PE> basis label allocation (see
Section 4.1.1) may consume too many labels in per-platform label
space. Sometimes we want to use the same EVPN label in all Leaf A-D
routes and IMET routes of the same EVI. So we allocate a context-
specific label (CSL) for a context VC in this section.
The EVPN label is still allocated from per-platform label space, and
it identifies the EVPN instance as per [RFC7432]. But it also
identifies a context label space CLS1. The VC label of the context
VC is allocated in CLS1. So we say that the VC label is a context-
specific VC label.
The encapsulation of the Context-Specific VC Label is illustrated as
the following figure:
+---------------------------------+
| underlay ethernet header |
+---------------------------------+
| PSN tunnel label |
+---------------------------------+
| EVPN label |
+---------------------------------+
| Context VC Label |
+---------------------------------+
| overlay ethernet or IP header |
+---------------------------------+
Figure 1: Encapsulation of EVI-Specific VC Label for EVPN Payload
Wang & Song Expires 16 February 2021 [Page 7]
Internet-Draft EVPN Context Label August 2020
Note that the Context-VC Label here is not the Context Label Space
(CLS) ID of the EVPN Label. But the EVPN label is the CLS-ID of the
Context-VC Label. That's why the CLS-ID EC (see section 3.1 of
[I-D.ietf-bess-mvpn-evpn-aggregation-label]) is not appropriate for
such encapsulation.
We introduce a new BGP Extended Community called Context-specific
Label (CSL) Entry Extended Community, the CSL-Entry EC was used to
carry the downstream-assigned context-specific VC labels.
4.1.3. CSL-Entry Extended Community
CSL-Entry Extended Community is a new Transitive Opaque EC with the
following structure (Sub-Type value to be assigned by IANA):
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x03 or 0x43 | Sub-Type | CSL-Type |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| CSL-Value |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 2: CSL-Entry Extended Community
* CSL-Type: A 2-octet field that specifies the type of Context-
Specific Label (CSL). In this document, the CSL-Type is 0,
indicating that the CSL-Value field is a downstream-assigned label
whose label space is identified by the EVPN label of the same
route.
* CSL-Value: A 4-octet field that specifies the value of CSL-Entry.
When it is a label (with CSL-Type 0), the most significant 20-bit
is set to the label value.
The "sub-type" field of the CSL-Entry EC has a different codepoint
from the CLS-ID EC. The CSL-Value of the CSL-Entry EC is a MPLS
label in a context-specific label space identified by the PTA label.
And the MPLS label in the CSL-Entry EC will be pushed onto the label
stack before the PTA label by the ingress PE. Typically, the MPLS
label of the CSL-Entry EC is a downstream assigned label, which means
that it will be used as an outgoing label by the PE receiving the
CSL-Entry EC, not as incomming label.
When constructing the Leaf A-D route, the IR-PTA label is the EVPN
Label, as per [RFC7432]. But the CSL-value in the CSL-Entry EC is a
label (say L1) that is allocated per TPE basis in CLS1. In fact, L1
Wang & Song Expires 16 February 2021 [Page 8]
Internet-Draft EVPN Context Label August 2020
is the context-specific VC label of the context VC of that ingress
TPE. That's why the context VC is called as CSL-based context VC.
So the CLS1-specific VC label need to be pushed onto the label stack
before EVPN Label (which identifies CLS1) on ingress PEs.
Note that when the PTA label is changed to a new value (caused by the
BGP nexthop rewriting) by the SPE nodes, the CSL-Entry in the same
EVPN route won't be rewrite. This is similar to the behavior of ESI
Label EC of EAD per ES route.
4.2. The Sharing of Context VCs
4.2.1. Using Admin-EVI
Note that the CSL-Entry ECs (for different EVIs) received from the
same TPE may be the same label, because that all EVLs on the same PE
may identify the same Context-specific Label Space (CLS). So we can
select a single EVI to use the Leaf A-D route with CSL-Entry EC in
such case. This EVI is called as administrating EVI (admin-EVI).
The context VC label carried in the Leaf A-D routes of the admin-EVI
will be used to take the place of the PTA label of the IMET route
with the same ORIP in all other ordinary EVIs in such case.
Note that all other ordinary EVIs don't have to use the Leaf A-D
routes with IR-PTA in their signalling procedures, they can use
ordinary IMET routes instead. The admin-EVI need to be configured on
all EVPN-PEs in such case.
4.2.2. Using per-platform VC labels
The admin EVIs may allocate the VC labels of its context VCs in the
per-platform label space.
Even if these VC labels are allocated in the per-platform label
space, The CSL-Entry EC is still necessary.
Because that the Context VC is not expected to be used to determine
the forwarding path of the data packet. They just identify the
context of the data packet (typically the ingress PE of the data
packet). So they should not be rewritten even when the nexthop of
the EVPN route is rewriten. When the Leaf routes use PTA label
(instead of CSL-entry EC) to carry the Context VC Label, The PTA
label will be rewritten on SPE nodes. It is just not our
expectation.
Wang & Song Expires 16 February 2021 [Page 9]
Internet-Draft EVPN Context Label August 2020
Note that the SPEs don't have to recognize the CSL-Entry EC, because
that it's a transitive opaque EC. The EVPN label of the admin-EVIs
in the PTA is unuseful. But they should also be included so as to
pass though the SPE nodes.
4.3. Establish Ingress Replication List by Leaf A-D Route
T1: ===R3(IMET)======>
PE1----------------------------PE2
T2: <==R1(IMET)=======
T3: ===R2(Leaf A-D)==>
Figure 3: The Leaf A-D Route's Ordinal Number
PE2 receives (at time T3) the responding Leaf A-D route (say R2) of
the IMET route R1 which is previously (at time T2) advertised by
itself, and PE2 preiously (at time T1) received an IMET route R3 with
the same ORIP as the self-ORIP of R2 . Given that R1,R2 and R3 both
have a IR-PTA, PE2 SHOULD use R2 to install the Ingress Replication
List (IRL) item for PE1 instead, and R3 will not used to install the
IRL-item for PE1 from then on.
Note that when R2 included a CSL-Entry EC, the CSL-value of the CSL-
Entry EC will be used as the outgoing label of the IRL-item. The
MPLS label of the IR-PTA will be used as the context label (CL) of
the CSL-Entry in NHLFE. No ILM entry will be installed for the CSL
of R2 on PE2.
Note that when PE2 sent R1 (at time T2) to other PEs(including PE1),
it will set the LIR flag of R1 to one. At the same time, PE2 will
add an import RT (say RT1) to the EVPN instance. When PE1 send R2
(at time T3) to PE2 as R1's reply, PE1 will add the same RT1 to R2,
because PE1 assumes that RT1 should have been added to the EVPN
instance by PE2 as an import RT. Otherwise PE2 wouldn't set the LIR
flag to one during the advertisement of R1.
4.4. Backward Compatibility
In [RFC7432], the LIR flag of IMET route is required to be zero when
it is advertised and to be ignored on receipt.
It means that the LIR flag is reserved by [RFC7432], but it
technically can be used in the future. What should the LIR flag be
restrained in the future use is no more severer than any other
reserved PTA flags in the IMET routes.
Wang & Song Expires 16 February 2021 [Page 10]
Internet-Draft EVPN Context Label August 2020
So when PE2 set the LIR flag to one in the IMET route and send it to
PE1, PE2 won't expect that the IMET route must be responded by a Leaf
A-D. When the corresponding Leaf A-D route can't be received from
PE1, the IMET route from PE1 still be used as per [RFC7432]. But
when PE1 is a new PE following this draft, PE1 will indeed respond a
Leaf A-D route for the IMET route.
The EVPN S-PMSI routes for (C-*,C-*) may be a succedaneum of IMET
routes. Such EVPN S-PMSI route is called wildcard S-PMSI route in
these document. The LIR flag of wildcard S-PMSI route is not
reserved. So there won't be any controversial issues on the
compatibilities of Leaf A-D route responsing. But we prefer the IMET
routes, because the IMET routes with non-zero LIR flag won't conflict
with [RFC7432] either.
5. Solutions
5.1. Solution for Source-Squelching in Hub-Spoke Scenarios
PEs3--------RR2--------+
PEh------CE3
CE1----PEs1--------RR1--------+
/
CE2----PEs2-------/
Figure 4: Hub PE and Spoke PEs
Now take above use case for example, there are three spoke PEs and
one hub PE. The spoke PEs are PEs1, PEs2 and PEs3. The hub PE is
PEh. Two of the spoke PEs (PEs1 and PEs2) are connected to the same
RR group and the third one connects to another RR group.
Although we can advertise different EVPN labels for different RR
groups, we can't advertise different EVPN labels for PEs1 and PEs2 by
default. In order to advertise different EVPN labels for PEs1 and
PEs2, PEh may use BGP ADD-PATH to advertise two NLRIs (of the same
EVI) to RR1, each along with a different EVPN label.
But this approach will cause some issues. Because that the BGP ADD-
PATH is typically used for ECMP purpose. But we don't expect RR1 to
do ECMP for these two NLRIs. That's the first issue. The second
issue is that we can't expect that PEs1/PEs2 will import one of (and
exactly only one of) these two NLRIs, even if PEh adds some intended
RTs along with these NLRIs. Because that such RT may be not so
intended from the view point of PEs1/PEs2. The third issue is that
when RR1 receives these two NLRIs, RR1 may just reflect one of them
to its clients because that their nexthop is the same IP address.
Wang & Song Expires 16 February 2021 [Page 11]
Internet-Draft EVPN Context Label August 2020
But PEh can request PEs1 or PEs2 to push the label of the context VC
from them to PEh. Benefit from the context VC label, PEh can
distinguish where the packet from, in other words, PEh can decide
where the packet can't be sent to.
The signaling for the hub PE to request the spoke PE to push the
context VC label will be the CSL-Entry EC, regardless of the label-
space type of the context VC label.
Note that although PEs1 and PEs2 can receive EVPN routes from each
other they won't import these routes because of the hub/spoke
behaviors.
5.2. Solution for per ingress statistics
We use CSL-based per-EVI context-VCs(see Section 4.1.2) to do per-
ingress statistics.
Note that The per-platform label space can be used as CLS1 at the
same time. In such case, the inner context-VC label is similar to
the downstream-assigned ESI-label in ILM-lookup behavior. Such
context-VC is very similar to the shared context VC too.
Note that when PE1 sends a Leaf A-D route with a CSL-Entry EC to PE2,
but PE2 don't recognize the CSL-Entry EC, then PE2 will encapsulate
the EVPN label without the inner context-VC label. If CLS1 is
actually identical to the per-platform label space, this will work as
well as [RFC7432], although the per-ingress statistics can't be
executed.
Note that legacy PEs will not send a Leaf A-D route in response to an
IMET route even if the LIR flag in the IMET route is set to one. So
when legacy PEs and new PEs following this section coexist in the
same EVI, they can interwork well, but only the new PEs can do per-
ingress statistics.
5.3. Solution for AR REPLICATOR in MPLS EVPN
LEAF1--------REPLICATOR1--------RNVE1
/
LEAF2-----------/
Figure 5: AR REPLICATOR in MPLS EVPN
Wang & Song Expires 16 February 2021 [Page 12]
Internet-Draft EVPN Context Label August 2020
When REPLICATOR1 node recieves an IMET Route with AR-role = AR-LEAF
from LEAF1 node, REPLICATOR1 SHOLD respond to it with an Leaf A-D
route with AR-PTA. The MPLS label field of the AR-PTA (say AR-PTA
Label) will be allocated following the same rules as the IR-PTA Label
in Section 4.1. When AR-LEAF1 receives above Leaf A-D route, the
Leaf A-D route is treated as a Replicator-AR route for the same ORIP,
then the control-plane procedures follows
[I-D.ietf-bess-evpn-optimized-ir]. When REPLICATOR1 receives data
packets from the AR-PTA Label, REPLICATOR1 will do source-squelching
for LEAF1, which means that these data packets will not be forwarded
back to LEAF1.
Note that the old Replicator-AR route (from AR-REPLICATOR) which is
in terms of IMET route will not be installed in dataplane by MPLS
EVPN AR-LEAF. Because that the Leaf A-D route (from AR-RPELICATOR)
will take it's place on AR-LEAF node. But the old Regular-IR route
(from AR-REPLICATOR) should still be installed by MPLS EVPN AR-LEAFs.
As what is discussed in Section 4.4, the wildcard S-PMSI route can be
used to replace the IMET route between AR-REPLICATOR and its AR-
LEAFs.
5.4. Solution for anycast tunnel usage on SPE
/--------SPE1-------\
TPE1 TPE2
\--------SPE2-------/
Figure 6: SPE with Anycast Tunnel
Now take above use case for example, the two SPEs are the egress
nodes of an anycast SR-MPLS tunnel. The anycast SR-MPLS tunnel is
used to transport flows from TPE1 to either SPE1 or SPE2 according to
load balancing procedures. So SPE1 and SPE2 have to advertise the
same EVPN label independently for a given EVPN route.
5.4.1. Control-plane
In fact, SPE1 and SPE2 can simply inherit the EVPN label (say EVL4)
from TPE2, and they advertise it to TPE1 along with a context-VC
label (say VCL4). The context-VC label is for the shared context-VC
from TPE2 to SPE1 or SPE2. We can make the VC labels from TPE2 to
SPE1 and SPE2 have the same value through configuring.
Wang & Song Expires 16 February 2021 [Page 13]
Internet-Draft EVPN Context Label August 2020
Note that the context-VC labels (in the admin-EVI) can be advertised
according to Section 4.2.2. Then the context-VCs will be established
according to Section 4.2.2 too. Note that VCL4 identify a Label
Space (say TPE2-specific CLS) that is dedicated to turning the EVL
received from TPE2 into an incoming label on the SPEs. When SPE1
receives EVPN labels from different TPEs, SPE1 MUST use different CLS
to install the corresponding ILM entry for Label swapping.
Then the VCL4 are advertised (along with the EVL) in the form of CLS-
ID EC, not in the form of CSL-Entry EC. Because that VCL4 is the
outer label of the EVL, not the inner label.
5.4.2. Data-plane
The label stack on the anycast SR-MPLS tunnel is constructed by TPE1
as the following:
+---------------------------------+
| underlay ethernet header |
+---------------------------------+
| Anycast SR-TL = SR_LSP_to_SPEs |
+---------------------------------+
| Context-VC Label = VCL4 |
+---------------------------------+
| EVPN label = EVL4 |
+---------------------------------+
| overlay ethernet or IP header |
+---------------------------------+
Figure 7: Anycast SPE dataplane
Note that the SR Tunnel Label (TL) in the label stack is the anycast
SR-LSP label from TPE1 to the SPE1 or SPE2.
Note that the context-VC is constructed in per-platform label space,
and VC labels from TPE2 to SPE1 and SPE2 will be the same value. so
the label stacks on the anycast tunnel are the same for SPE1 and
SPE2.
Then SPE1/SPE2 will perform ILM lookup for the EVPN label in the
"TPE2-specific label space" which is identified by the context-VC
label VCL4. The label operation will be "swap", and the new outgoing
EVPN label will be the same value (as EVL4).
Wang & Song Expires 16 February 2021 [Page 14]
Internet-Draft EVPN Context Label August 2020
5.4.3. Dynamical VCL Allocation and Advertisement
Typically, the control plane in Section 4.2.2 doesn't have to ensure
that the context-VCs from the same PE to different PEs should use the
same VCL. But in this use case, it is necessary. We use static
configuration to ensure that requirement in Section 5.4.1. But this
will bring out complexity of its management plane.
In order to simply such administrative complexity, the signalling of
admin-EVI may not base on Section 4. It is feasible for such
signalling to be implemented on the basis of Kompella VPLS signalling
or BGP SR signaling. But it will be better for the admin-EVI and
EVPN VPLS to use the same signalling framework.
So we can just transplant the SRGB or VE-Block configuration model
into the admin-EVI but still use the signalling of Section 5.4.1.
6. Security Considerations
This section will be added in future versions.
7. IANA Considerations
The IANA considerations for CSL-Entry EC in Section 4.1.2 will be
added in future versions.
8. Acknowledgements
The authors would like to thank the following for their comments and
review of this document:
Benchong Xu.
9. References
9.1. Normative References
[I-D.ietf-bess-evpn-bum-procedure-updates]
Zhang, Z., Lin, W., Rabadan, J., Patel, K., and A.
Sajassi, "Updates on EVPN BUM Procedures", Work in
Progress, Internet-Draft, draft-ietf-bess-evpn-bum-
procedure-updates-08, 18 November 2019,
<https://tools.ietf.org/html/draft-ietf-bess-evpn-bum-
procedure-updates-08>.
[I-D.ietf-bess-evpn-optimized-ir]
Rabadan, J., Sathappan, S., Lin, W., Katiyar, M., and A.
Sajassi, "Optimized Ingress Replication solution for
Wang & Song Expires 16 February 2021 [Page 15]
Internet-Draft EVPN Context Label August 2020
EVPN", Work in Progress, Internet-Draft, draft-ietf-bess-
evpn-optimized-ir-07, 13 July 2020,
<https://tools.ietf.org/html/draft-ietf-bess-evpn-
optimized-ir-07>.
[I-D.ietf-bess-mvpn-evpn-aggregation-label]
Zhang, Z., Rosen, E., Lin, W., Li, Z., and I. Wijnands,
"MVPN/EVPN Tunnel Aggregation with Common Labels", Work in
Progress, Internet-Draft, draft-ietf-bess-mvpn-evpn-
aggregation-label-03, 24 October 2019,
<https://tools.ietf.org/html/draft-ietf-bess-mvpn-evpn-
aggregation-label-03>.
[RFC6514] Aggarwal, R., Rosen, E., Morin, T., and Y. Rekhter, "BGP
Encodings and Procedures for Multicast in MPLS/BGP IP
VPNs", RFC 6514, DOI 10.17487/RFC6514, February 2012,
<https://www.rfc-editor.org/info/rfc6514>.
[RFC7432] Sajassi, A., Ed., Aggarwal, R., Bitar, N., Isaac, A.,
Uttaro, J., Drake, J., and W. Henderickx, "BGP MPLS-Based
Ethernet VPN", RFC 7432, DOI 10.17487/RFC7432, February
2015, <https://www.rfc-editor.org/info/rfc7432>.
9.2. Informative References
[RFC3031] Rosen, E., Viswanathan, A., and R. Callon, "Multiprotocol
Label Switching Architecture", RFC 3031,
DOI 10.17487/RFC3031, January 2001,
<https://www.rfc-editor.org/info/rfc3031>.
[RFC5331] Aggarwal, R., Rekhter, Y., and E. Rosen, "MPLS Upstream
Label Assignment and Context-Specific Label Space",
RFC 5331, DOI 10.17487/RFC5331, August 2008,
<https://www.rfc-editor.org/info/rfc5331>.
Authors' Addresses
Yubao Wang
ZTE Corporation
No. 50 Software Ave, Yuhuatai Distinct
Nanjing
China
Email: yubao.wang2008@hotmail.com
Wang & Song Expires 16 February 2021 [Page 16]
Internet-Draft EVPN Context Label August 2020
Bing Song
ZTE Corporation
No. 50 Software Ave, Yuhuatai Distinct
Nanjing
China
Email: song.bing@zte.com.cn
Wang & Song Expires 16 February 2021 [Page 17]