DTN Management Architecture
draft-ietf-dtn-dtnma-07
The information below is for an old version of the document.
| Document | Type |
This is an older version of an Internet-Draft whose latest revision state is "Active".
|
|
|---|---|---|---|
| Authors | Edward J. Birrane , Sarah Heiner , Emery Annis | ||
| Last updated | 2023-11-10 (Latest revision 2023-10-23) | ||
| Replaces | draft-ietf-dtn-ama | ||
| RFC stream | Internet Engineering Task Force (IETF) | ||
| Formats | |||
| Reviews |
INTDIR Telechat review
(of
-10)
by Donald Eastlake
On the Right Track
|
||
| Additional resources | Mailing list discussion | ||
| Stream | WG state | Submitted to IESG for Publication | |
| Document shepherd | Rick Taylor | ||
| Shepherd write-up | Show Last changed 2023-11-10 | ||
| IESG | IESG state | Publication Requested | |
| Consensus boilerplate | Unknown | ||
| Telechat date | (None) | ||
| Responsible AD | Zaheduzzaman Sarker | ||
| Send notices to | rick.taylor@ori.co |
draft-ietf-dtn-dtnma-07
Delay-Tolerant Networking E.J. Birrane
Internet-Draft S.E. Heiner
Intended status: Informational E. Annis
Expires: 25 April 2024 Johns Hopkins Applied Physics Laboratory
23 October 2023
DTN Management Architecture
draft-ietf-dtn-dtnma-07
Abstract
The Delay-Tolerant Networking (DTN) architecture describes a type of
challenged network in which communications may be significantly
affected by long signal propagation delays, frequent link
disruptions, or both. The unique characteristics of this environment
require a unique approach to network management that supports
asynchronous transport, autonomous local control, and a small
footprint (in both resources and dependencies) so as to deploy on
constrained devices.
This document describes a DTN management architecture (DTNMA)
suitable for managing devices in any challenged environment but, in
particular, those communicating using the DTN Bundle Protocol (BP).
Operating over BP requires an architecture that neither presumes
synchronized transport behavior nor relies on query-response
mechanisms. Implementations compliant with this DTNMA should expect
to successfully operate in extremely challenging conditions, such as
over uni-directional links and other places where BP is the preferred
transport.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on 25 April 2024.
Birrane, et al. Expires 25 April 2024 [Page 1]
Internet-Draft DTNMA October 2023
Copyright Notice
Copyright (c) 2023 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents (https://trustee.ietf.org/
license-info) in effect on the date of publication of this document.
Please review these documents carefully, as they describe your rights
and restrictions with respect to this document. Code Components
extracted from this document must include Revised BSD License text as
described in Section 4.e of the Trust Legal Provisions and are
provided without warranty as described in the Revised BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1. Scope . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.2. Requirements Language . . . . . . . . . . . . . . . . . . 5
1.3. Organization . . . . . . . . . . . . . . . . . . . . . . 5
2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 6
3. Challenged Network Overview . . . . . . . . . . . . . . . . . 8
3.1. Challenged Network Constraints . . . . . . . . . . . . . 8
3.2. Topology and Service Implications . . . . . . . . . . . . 9
3.2.1. Management Implications . . . . . . . . . . . . . . . 10
3.3. Management Special Cases . . . . . . . . . . . . . . . . 11
4. Desirable Design Properties . . . . . . . . . . . . . . . . . 11
4.1. Dynamic Architectures . . . . . . . . . . . . . . . . . . 12
4.2. Hierarchically Modeled Information . . . . . . . . . . . 12
4.3. Adaptive Push of Information . . . . . . . . . . . . . . 13
4.4. Efficient Data Encoding . . . . . . . . . . . . . . . . . 14
4.5. Universal, Unique Data Identification . . . . . . . . . . 15
4.6. Runtime Data Definitions . . . . . . . . . . . . . . . . 15
4.7. Autonomous Operation . . . . . . . . . . . . . . . . . . 16
5. Current Network Management Approaches . . . . . . . . . . . . 17
5.1. Simple Network Management Protocol (SNMP) . . . . . . . . 18
5.2. XML-Based Protocols . . . . . . . . . . . . . . . . . . . 19
5.2.1. The YANG Data Model . . . . . . . . . . . . . . . . . 19
5.2.2. XML-Based Management Protocols . . . . . . . . . . . 20
5.3. Autonomic Networking . . . . . . . . . . . . . . . . . . 21
6. Motivation for New Features . . . . . . . . . . . . . . . . . 22
7. Reference Model . . . . . . . . . . . . . . . . . . . . . . . 23
7.1. Important Concepts . . . . . . . . . . . . . . . . . . . 23
7.2. Model Overview . . . . . . . . . . . . . . . . . . . . . 24
7.3. Functional Elements . . . . . . . . . . . . . . . . . . . 25
7.3.1. Managed Applications and Services . . . . . . . . . . 25
7.3.2. DTNMA Agent (DA) . . . . . . . . . . . . . . . . . . 26
7.3.3. Managing Applications and Services . . . . . . . . . 28
Birrane, et al. Expires 25 April 2024 [Page 2]
Internet-Draft DTNMA October 2023
7.3.4. DTNMA Manager (DM) . . . . . . . . . . . . . . . . . 29
7.3.5. Pre-Shared Definitions . . . . . . . . . . . . . . . 31
8. Desired Services . . . . . . . . . . . . . . . . . . . . . . 31
8.1. Local Monitoring and Control . . . . . . . . . . . . . . 32
8.2. Local Data Fusion . . . . . . . . . . . . . . . . . . . . 32
8.3. Remote Configuration . . . . . . . . . . . . . . . . . . 33
8.4. Remote Reporting . . . . . . . . . . . . . . . . . . . . 34
8.5. Authorization . . . . . . . . . . . . . . . . . . . . . . 34
9. Logical Autonomy Model . . . . . . . . . . . . . . . . . . . 34
9.1. Overview . . . . . . . . . . . . . . . . . . . . . . . . 35
9.2. Model Characteristics . . . . . . . . . . . . . . . . . . 37
9.3. Data Value Representation . . . . . . . . . . . . . . . . 39
9.4. Data Reporting . . . . . . . . . . . . . . . . . . . . . 39
9.5. Command Execution . . . . . . . . . . . . . . . . . . . . 40
9.6. Predicate Autonomy Rules . . . . . . . . . . . . . . . . 41
10. Use Cases . . . . . . . . . . . . . . . . . . . . . . . . . . 41
10.1. Notation . . . . . . . . . . . . . . . . . . . . . . . . 41
10.2. Serialized Management . . . . . . . . . . . . . . . . . 42
10.3. Intermittent Connectivity . . . . . . . . . . . . . . . 43
10.4. Open-Loop Reporting . . . . . . . . . . . . . . . . . . 45
10.5. Multiple Administrative Domains . . . . . . . . . . . . 46
10.6. Cascading Management . . . . . . . . . . . . . . . . . . 48
11. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 50
12. Security Considerations . . . . . . . . . . . . . . . . . . . 50
13. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 50
14. Informative References . . . . . . . . . . . . . . . . . . . 50
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 54
1. Introduction
The Delay-Tolerant Networking (DTN) architecture, as described in
[RFC4838], has been designed to cope with data exchange in challenged
networks. Just as the DTN architecture requires new capabilities for
transport and transport security, special consideration must be given
for the management of DTN devices.
This document describes a DTN Management Architecture (DTNMA)
providing configuration, monitoring, and local control of both
application and network services on a managed device. The DTNMA is
designed to provide for the management of devices operating either
within or across a challenged network.
Birrane, et al. Expires 25 April 2024 [Page 3]
Internet-Draft DTNMA October 2023
Fundamental properties of a challenged network are outlined in
Section 2.2.1 of [RFC7228]. These properties include lacking end-to-
end IP connectivity, having "serious interruptions" to end-to-end
connectivity, and exhibiting delays longer than can be tolerated by
end-to-end synchronization mechanisms (such as TCP). It is further
noted that the DTN architecture was designed to cope with such
networks.
| NOTE: These challenges may be caused by physical impairments
| such as long signal propagation and frequent link disruption,
| or by other factors such as quality-of-service prioritization,
| service-level agreements, and other consequences of traffic
| management and scheduling.
Device management in these environments must occur without human
interactivity, without system-in-the-loop synchronous function, and
without requiring a synchronous underlying transport layer. This
means that managed devices need to determine their own schedules for
data reporting, their own operational configuration, and perform
their own error discovery and mitigation.
Certain outcomes of device self-management should be determinable by
a privileged external observer (such as a managing device). In a
challenged network, these observers may need to communicate with a
managed device after significant periods of disconnectedness. Non-
deterministic behavior of a managed device may make establishing
communication difficult or impossible.
The desire to define asynchronous and autonomous device management is
not new. However, challenged networks (in general) and the DTN
environment (in particular) represent unique deployment scenarios and
impose unique design constraints. To the extent that these
environments differ from more traditional, enterprise networks, their
management may also differ from the management of enterprise
networks. Therefore, existing techniques may need to be adapted to
operate in the DTN environment or new techniques may need to be
created.
| NOTE: The DTNMA is designed to leverage any transport, network,
| and security solutions designed for challenged networks.
| However, the DTNMA should operate in any environment in which
| the Bundle Protocol (BPv7) [RFC9171] is deployed.
Birrane, et al. Expires 25 April 2024 [Page 4]
Internet-Draft DTNMA October 2023
1.1. Scope
This document describes the desirable properties of, and motivation
for, a DTNMA. This document also provides a reference model, service
descriptions, autonomy model, and use cases to better reason about
ways to standardize and implement this architecture.
This is not a normative document and the information herein is not
meant to represent a standardization of any data model, protocol, or
implementation. Instead, this document provides informative guidance
to authors and users of such models, protocols, and implementations.
The selection of any particular transport or network layer is outside
of the scope of this document. The DTNMA does not require the use of
any specific protocol such as IP, BP, TCP, or UDP. In particular,
the DTNMA design does not assume the use of either IPv4 or IPv6.
| NOTE: The fact that the DTNMA must operate in any environment
| that deploys BP does not mean that the DTNMA requires the use
| of BP to operate.
Network features such as naming, addressing, routing, and security
are out of scope of the DTNMA. It is presumed that any operational
network communicating DTNMA messages would implement these services
for any payloads carried by that network.
The interactions between and amongst the DTNMA and other management
approaches are outside of the scope of this document.
1.2. Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
1.3. Organization
The remainder of this document is organized into the following nine
sections, described as follows.
* Terminology - This section identifies terms fundamental to
understanding DTNMA concepts. Whenever possible, these terms
align in both word selection and meaning with their use in other
management protocols.
* Challenged Network Overview - This section describes important
aspects of challenged networks and necessary approaches for their
management.
Birrane, et al. Expires 25 April 2024 [Page 5]
Internet-Draft DTNMA October 2023
* Desirable Design Properties - This section defines those
properties of the DTNMA that must be present to operate within the
constraints of a challenged network. These properties are similar
to the specification of system-level requirements of a DTN
management solution.
* Current Network Management Approaches - This section provides a
brief overview of existing network management approaches. Where
possible, the DTNMA adopts concepts from these approaches. The
limitations of current approaches from the perspective of the
DTNMA desirable properties are identified and discussed.
* Motivation for New Features - This section provides an overall
motivation for this work, to include explaining why a management
architecture for challenged networks is useful and necessary.
* Reference Model - This section defines a reference model that can
be used to reason about the DTNMA independent of an
implementation. This model identifies the logical elements of the
system and the high-level relationships and behaviors amongst
those elements.
* Desired Services - This section identifies and defines the DTNMA
services provided to network and mission operators.
* Logical Autonomy Model - This section provides an exemplar data
model that can be used to reason about DTNMA control and data
flows. This model is based on the DTNMA reference model.
* Use Cases - This section presents multiple use cases accommodated
by the DTNMA architecture. Each use case is presented as a set of
control and data flows referencing the DTNMA reference model and
logical autonomy model.
2. Terminology
This section defines terminology that either is unique to the DTNMA
or is necessary for understanding the concepts defined in this
specification.
* Controls: Procedures run by a DA to change the behavior,
configuration, or state of an application or protocol managed by
that DA. This includes procedures to manage the DA itself, such
as to have the DA produce performance reports or to apply new
management policies.
Birrane, et al. Expires 25 April 2024 [Page 6]
Internet-Draft DTNMA October 2023
* DTN Management: Management that does not depend on stateful
connections, timely delivery of management messages, or closed-
loop control.
* DTNMA Agent (DA): A role associated with a managed device,
responsible for reporting performance data, accepting policy
directives, performing autonomous local control, error-handling,
and data validation. DAs exchange information with DMs operating
either on the same device and/or on remote devices in the network.
* DTNMA Manager (DM): A role associated with a managing device
responsible for configuring the behavior of, and eventually
receiving information from, DAs. DMs interact with one or more
DAs located on the same device and/or on remote devices in the
network.
* Externally Defined Data (EDD): Typed information made available to
a DA by its hosting device, but not computed directly by the DA
itself.
* Macros: Named, ordered collections of Controls and/or other
macros.
* Data Reports: Typed, ordered collections of data values gathered
by one or more DAs and provided to one or more DMs. Reports
comply to the format of a given Data Report Schema.
* Data Report Schemas: Named, ordered collection of data names that
represent the schema of a Data Report.
* Rules: Unit of autonomous specification that provides a stimulus-
response relationship between time or state on a DA and the
actions or operations to be run as a result of that time or state.
* State-Based Rule (SBR): Any Rule triggered by the calculable,
internal state of the DA.
* Time-Based Rule (TBR): A specialization, and simplification, of a
State-Based Rule in which the rule stimulus is triggered by
relative or absolute time on a DA.
* Variables (VARs): Typed information computed internal to a DA.
Birrane, et al. Expires 25 April 2024 [Page 7]
Internet-Draft DTNMA October 2023
3. Challenged Network Overview
The DTNMA provides network management services able to operate in a
challenged network environment, such as envisioned by the DTN
architecture. This section describes what is meant by the term
"challenged network", the important properties of such a network, and
observations on impacts to conventional management approaches.
3.1. Challenged Network Constraints
Constrained networks are defined as networks where "some of the
characteristics pretty much taken for granted with link layers in
common use in the Internet at the time of writing are not
attainable." [RFC7228]. This broad definition captures a variety of
potential issues relating to physical, technical, and regulatory
constraints on message transmission. Constrained networks typically
include nodes that regularly reboot or are otherwise turned off for
long periods of time, transmit at low or asynchronous bitrates, and/
or have very limited computational resources.
Separately, a challenged network is defined as one that "has serious
trouble maintaining what an application would today expect of the
end-to-end IP model" [RFC7228]. This definition includes networks
where there is never simultaneous end-to-end connectivity, when such
connectivity is interrupted at planned or unplanned intervals, or
when delays exceed those that could be accommodated by IP-based
transport. Links in such networks are often unavailable due to
attenuation, propagation delays, mobility, occultation, and other
limitations imposed by energy and mass considerations.
| NOTE: Because challenged networks might not provide services
| expected of the end-to-end IP model, devices in such networks
| might not implement networking stacks associated with the end-
| to-end IP model. This means that devices might not include
| support for certain transport protocols (TCP/UDP), web
| protocols (HTTP), or even internetworking protocols (IPv4/
| IPv6).
By these definitions, a "challenged" network is a special type of
"constrained" network, where the constraints are related to end-to-
end connectivity and delays. As such, "all challenged networks are
constrained networks ... but not all constrained networks are
challenged networks ... Delay-Tolerant Networking (DTN) has been
designed to cope with challenged networks" [RFC7228].
Birrane, et al. Expires 25 April 2024 [Page 8]
Internet-Draft DTNMA October 2023
Solutions that work in constrained networks might not be solutions
that work in challenged networks. In particular, challenged networks
exhibit the following properties that impact the way in which the
function of network management is considered.
* No end-to-end path is guaranteed to exist at any given time
between any two nodes.
* Round-trip communications between any two nodes within any given
time window may be impossible.
* Latencies on the order of seconds, hours, or days must be
tolerated.
* Links may be uni-directional.
* Bi-directional links may have asymmetric data rates.
* The existence of external infrastructure, software, systems, or
processes such as a Domain Name Service (DNS) or a Certificate
Authority (CA) cannot be guaranteed.
3.2. Topology and Service Implications
The set of constraints that might be present in a challenged network
impact both the topology of the network and the services active
within that network.
Operational networks handle cases where nodes join and leave the
network over time. These topology changes may or may not be planned,
they may or may not represent errors, and they may or may not impact
network services. Challenged networks differ from other networks not
in the present of topological change, but in the likelihood that
impacts to topology result in impacts to network services.
The difference between topology impacts and service impacts can be
expressed in terms of connectivity. Topological connectivity usually
refers to the existence of a path between an application message
source and destination. Service connectivity, alternatively, refers
to the existence of a path between a node and one or more services
needed to process (often just-in-time) application messaging.
Examples of service connectivity include access to infrastructure
elements such as a Domain Name System (DNS) or a Certificate
Authority (CA).
In networks that might be partitioned most of the time, it is less
likely that a node would concurrently access both an application
endpoint and one or more network service endpoints. For this reason,
Birrane, et al. Expires 25 April 2024 [Page 9]
Internet-Draft DTNMA October 2023
network services in a challenged network should be designed to allow
for asynchronous operation. Accommodating this use case often
involves the use of local caching, pre-placing information, and not
hard-coding message information at a source that might change when a
message reaches its destination.
| NOTE: One example of rethinking services in a challenged
| network is the securing of BPv7 bundles. The BPSec [RFC9172]
| security extensions to BPv7 do not encode security destinations
| when applying security. Instead, BPSec requires nodes in a
| network to identify themselves as security verifiers or
| acceptors when receiving and processing secured messages.
3.2.1. Management Implications
Network management approaches must adapt to the topology and service
impacts encountered in challenged networks. In particular, the ways
in which "managers" and "agents" in a management architecture operate
must consider how to operate with changes to topology and changes to
service endpoints.
When connectivity to a manager cannot be guaranteed, agents must rely
on locally available information and use local autonomy to react to
changes at the node. Architectures that rely on external resources
such as access to third-party oracles, operators-in-the-loop, or
other service infrastructure may fail to operate in a challenged
network.
In addition to disconnectivity, topological change can alter the
associations amongst managed and managing devices. Different
managing devices might be active in a network at different times or
in different partitions. Managed devices might communicate with
some, all, or none of these managing devices as a function of their
own local configuration and policy.
| NOTE: These concepts relate to practices in conventional
| networks. For example, supporting multiple managing devices is
| similar to deploying multiple instances of a network service --
| such as a DNS server or CA node. Selecting from a set of
| managing devices is similar to a sensor node practice of
| electing cluster heads to act as privileged nodes for data
| storage and exfiltration.
Therefore, a network management architecture for challenged networks
should:
1. Support a many-to-many association amongst managing and managed
devices, and
Birrane, et al. Expires 25 April 2024 [Page 10]
Internet-Draft DTNMA October 2023
2. Allow "control from" and "reporting to" managing devices to
function independent of one another.
3.3. Management Special Cases
The following special cases illustrate some of the operational
situations that can be encountered in the management of devices in a
challenged network.
* One-Way Management. A managed device can only be accessed via a
uni-directional link, or a via a link whose duration is shorter
than a single round-trip propagation time.
* Summary Data. A managing device can only receive summary data of
a managed device's state because a link or path is constrained by
capacity or reliability.
* Bulk Historical Reporting. A managing device receives a large
volume of historical report data for a managed device. This can
occur when a managed device rejoins a network or has access to a
high capacity link (or path) to the managed device.
* Multiple Managers. A managed device tracks multiple managers in
the network and communicates with them as a function of time,
local state, or network topology. This includes challenged
networks that interconnect two or more unchallenged networks such
that managed and managing devices exist in different networks.
These special cases highlight the need for managed devices to operate
without presupposing a dedicated connection to a single managing
device. To support this, managing devices must deliver instruction
sets that govern the local, autonomous behavior of managed devices.
These behaviors include (but are not limited to) collecting
performance data, state, and error conditions, and applying pre-
determined responses to pre-determined events. Managing devices in a
challenged network might never expect a reply to a command, and
communications from managed devices may be delivered much later than
the events being reported.
4. Desirable Design Properties
This section describes those design properties that are desirable
when defining a management architecture operating across challenged
links in a network. These properties ensure that network management
capabilities are retained even as delays and disruptions in the
network scale. Ultimately, these properties are the driving design
principles for the DTNMA.
Birrane, et al. Expires 25 April 2024 [Page 11]
Internet-Draft DTNMA October 2023
| NOTE: These properties may influence the design, construction,
| and adaptation of existing management tools for use in
| challenged networks. For example, the properties the DTN
| architecture [RFC4838] resulted in the development of BPv7
| [RFC9171] and BPSec [RFC9172]. The DTNMA may result in the
| construction of new management data models, policy expressions,
| and/or protocols.
4.1. Dynamic Architectures
The DTNMA should be agnostic of the underlying physical topology,
transport protocols, security solutions, and supporting
infrastructure of a given network. Due to the likelihood of
operating in a frequently partitioned environment, the topology of a
network may change over time. Attempts to stabilize an architecture
around individual nodes can result in a brittle management framework
and the creation of congestion points during periods of connectivity.
| NOTE: The DTNMA must run in every environment in which BP
| bundles may be used, even though the DTNMA does not require the
| use of BP for its transport.
The DTNMA should not prescribe any association between a DM and a DA
other than those defined in this document. There should be no
logical limitation to the number of DMs that can control a DA, the
number of DMs that a DA should report to, or any requirement that a
DM and DA relationship implies a pair.
| NOTE: Practical limitations on the relationships between and
| amongst DMs and DAs will exist as a function of the
| capabilities of networked devices. These limitations derive
| from processing and storage constraints, performance
| requirements, and other engineering factors. While this
| information is vital to the proper engineering of a managed and
| managing device, they are implementation considerations, and
| not otherwise design constraints on the DTNMA.
4.2. Hierarchically Modeled Information
The DTNMA should use data models to define the syntactic and semantic
contracts for data exchange between a DA and a DM. A given model
should have the ability to "inherit" the contents of other models to
form hierarchical data relationships.
| NOTE: The term data model in this context refers to a schema
| that defines a contract between a DA and a DM for how
| information is represented and validated.
Birrane, et al. Expires 25 April 2024 [Page 12]
Internet-Draft DTNMA October 2023
Many network management solutions use data models to specify the
semantic and syntactic representation of data exchanged between
managed and managing devices. The DTNMA is not different in this
regard - information exchanged between DAs and DMs should conform to
one or more pre-defined, normative data models.
A common best practice when defining a data model is to make it
cohesive. A cohesive model is one that includes information related
to a single purpose such as managing a single application or
protocol. When applying this practice, it is not uncommon to develop
a large number of small data models that, together, describe the
information needed to manage a device.
Another best practice for data model development is the use of
inclusion mechanisms to allow one data model to include information
from another data model. This ability to include a data model avoids
repeating information in different data models. When one data model
includes information from another data model, there is an implied
model hierarchy.
Data models in the DTNMA should allow for the construction of both
cohesive models and hierarchically related models. These data models
should be used to define all sources of information that can be
retrieved, configured, or executed in the DTNMA. This includes
supporting DA autonomy functions such as parameterization, filtering,
and event driven behaviors. These models will be used to both
implement interoperable autonomy engines on DAs and define
interoperable report parsing mechanisms on DMs.
| NOTE: While data model hierarchies can result in a more concise
| data model, arbitrarily complex nesting schemes can also result
| in very verbose encodings. Where possible, data
| identifications schemes should be constructed that allow for
| both hierarchical data and highly compressible data
| identification.
4.3. Adaptive Push of Information
DAs in the DTNMA architecture should determine when to push
information to DMs as a function of their local state.
Pull management mechanisms require a managing device to send a query
to a managed device and then wait for a response to that specific
query. This practice implies some serialization mechanism (such as a
control session) between entities. However, challenged networks
cannot guarantee timely round-trip data exchange. For this reason,
pull mechanisms must be avoided in the DTNMA.
Birrane, et al. Expires 25 April 2024 [Page 13]
Internet-Draft DTNMA October 2023
Push mechanisms, in this context, refer to the ability of DAs to
leverage local autonomy to determine when and what information should
be sent to which DMs. The push is considered adaptive because a DA
determines what information to push (and when) as an adaptation to
changes to the DA's internal state. Once pushed, information might
still be queued pending connectivity of the DA to the network.
| NOTE: Even in cases where a round-trip exchange can occur, pull
| mechanisms increase the overall amount of traffic in the
| network and preclude the use of autonomy at managed devices.
| So even when pull mechanisms are feasible they should not be
| considered a pragmatic alternative to push mechanisms.
4.4. Efficient Data Encoding
Messages exchanged between a DA and a DM in the DTNMA should be
defined in a way that allows for efficient on-the-wire encoding.
DTNMA design decisions that result in smaller message sizes should be
preferred over those that result in larger message sizes.
There is a relationship between message encoding and message
processing time at a node. Messages with little or no encodings may
simplify node processing whereas more compact encodings may require
additional activities to generate/parse encoded messages. Generally,
compressing a message takes processing time at the sender and
decompressing a message takes processing time at a receiver.
Therefore, there is a design tradeoff between minimizing message
sizes and minimizing node processing.
| NOTE: There are many ways in which message size, number of
| messages, and node behaviors can impact processing performance.
| Because the DTNMA does not presuppose any underlying protocol
| or implementation, this section is focused solely on the
| compactness of an individual message and the processing for
| encoding and decoding that individual message.
There is no advantage to minimizing node processing time in a
challenged network. The same sparse connectivity that benefits from
store-and-forward transport provides time at a node for data
processing prior to a future transmission opportunity.
However, there is a significant advantage to smaller message sizes in
a challenged network. Smaller messages require smaller periods of
viable transmission for communication, they incur less re-
transmission cost, and they consume less resources when persistently
stored en-route in the network.
Birrane, et al. Expires 25 April 2024 [Page 14]
Internet-Draft DTNMA October 2023
| NOTE: Naive approaches to minimizing message size through
| general purpose compression algorithms do not produce minimal
| encodings. Data models can, and should, be designed for
| compact encoding from the beginning. Design strategies for
| compact encodings involve using structured data instead of
| large hash values, reusable, hierarchical data models, and
| exploiting common structures in data models.
4.5. Universal, Unique Data Identification
Elements within the DTNMA should be uniquely identifiable so that
they can be individually manipulated. Further, these identifiers
should be universal - the identifier for a data element should be the
same regardless of role, implementation, or network instance.
Identification schemes that are relative to a specific DA or specific
system configuration might change over time. In particular, nodes in
a challenged network may change their status or configuration during
periods of partition from other parts of the network.
Resynchronizing relative state or configuration should be avoided
whenever possible.
| NOTE: Consider the common technique for approximating an
| associative array lookup. A manager wishing to perform an
| associative lookup for some key K1 will:
|
| 1. Query a list of array keys from an agent.
|
| 2. Find the key that matches K1 and infer the index of K1
| from the returned key list.
|
| 3. Query the discovered index on the agent to retrieve the
| desired data.
|
| Ignoring the inefficiency of two round-trip exchanges, this
| mechanism will fail if the agent changes its key-index mapping
| between the first and second query. While this is unlikely to
| occur in a low-latency network, it is more likely to occur in a
| challenged network.
4.6. Runtime Data Definitions
The DTNMA should allow for the definition of new elements to a data
model as part of the runtime operation of the management system.
These definitions may represent custom data definitions that are
applicable only for a particular device or network. Custom
definitions should also be able to be removed from the system during
runtime.
Birrane, et al. Expires 25 April 2024 [Page 15]
Internet-Draft DTNMA October 2023
The custom definition of new data from existing data (such as through
data fusion, averaging, sampling, or other mechanisms) provides the
ability to communicate desired information in as compact a form as
possible.
| NOTE: A DM could, for example, define a custom data report that
| includes only summary information around a specific operational
| event or as part of specific debugging. DAs could then produce
| this smaller report until it is no longer necessary, at which
| point the custom report could be removed from the management
| system.
Custom data elements should be calculated and used both as parameters
for DA autonomy and for more efficient reporting to DMs. Defining
new data elements allows for DAs to perform local data fusion and
defining new reporting templates allows for DMs to specify desired
formats and generally save on link capacity, storage, and processing
time.
4.7. Autonomous Operation
The management of applications by a DA should be achievable using
only knowledge local to the DA because DAs might need to operate
during times when they are disconnected from a DM.
DA autonomy may be used for simple automation of predefined tasks or
to support semi-autonomous behavior in determining when to run tasks
and how to configure or parameterize tasks when they are run. In
either case, a DA should provide the following features.
* Stand-alone Operation - Pre-configuration allows DAs to operate
without regular contact with other nodes in the network. The
initial configuration (and periodic update) of a DA autonomy
engine remains difficult in a challenged network, but removes the
requirement that a DM be in-the-loop during regular operations.
Sending stimuli-and-responses to a DA during periods of
connectivity allows DAs to self-manage during periods of
disconnectivity.
* Deterministic Behavior - Operational systems might need to act in
a deterministic way even in the absence of an operator in-the-
loop. Deterministic behavior allows an out-of-contact DM to
predict the state of a DA and to determine how a DA got into a
particular state.
Birrane, et al. Expires 25 April 2024 [Page 16]
Internet-Draft DTNMA October 2023
* Engine-Based Behavior - Operational systems might not be able to
deploy "mobile code" [RFC4949] solutions due to network bandwidth,
memory or processor loading, or security concerns. Engine-based
approaches provide configurable behavior without incurring these
concerns.
* Authentication, Authorization, and Accounting - The DTNMA does not
require a specific underlying transport protocol, network
infrastructure, or network services. Therefore, mechanisms for
authentication, authorization, and accounting must be present in a
standard way at DAs and DMs to provide these functions if the
underlying network does not. This is particularly true in cases
where multiple DMs may be active concurrently in the network.
Features such as deterministic processing and engine-based behavior
do not preclude the use of other Artificial Intelligence (AI) and
Machine Learning (ML) approaches on a managed device.
| NOTE: The deterministic automation of the DTNMA can monitor and
| control AI/ML management applications on a managed device.
| Using multiple levels of autonomy is a well-known method to
| balance the flexibility of a highly autonomous system with the
| reduced risk of a deterministic system.
5. Current Network Management Approaches
Several network management solutions have been developed for both
local-area and wide-area networks. Their capabilities range from
simple configuration and report generation to complex modeling of
device settings, state, and behavior. Each of these approaches are
successful in the domains for which they have been built, but are not
all equally functional when deployed in a challenged network.
Early network management tools designed for unchallenged networks
provide synchronous mechanisms for communicating locally-collected
data from devices to operators. Applications are managed using a
"pull" mechanism, requiring a managing device to explicitly request
the data to be produced and transmitted by a managed device.
| NOTE: Network management solutions that pull large sets of data
| might not operate in a challenged environment that cannot
| support timely, round-trip exchange of large data volumes.
More recent network management tools focus on message-based
management, reduced state keeping by managed and managing devices,
and increased levels of system autonomy.
Birrane, et al. Expires 25 April 2024 [Page 17]
Internet-Draft DTNMA October 2023
This section describes some of the well-known, standardized protocols
for network management and contrasts their purposes with the
desirable properties of the DTNMA. The purpose of this comparison is
to identify elements of existing approaches that can be adopted or
adapted for use in challenged networks and where new elements must be
created specifically for this environment.
5.1. Simple Network Management Protocol (SNMP)
The de facto example of a pull architecture is the Simple Network
Management Protocol (SNMP) [RFC3410]. SNMP utilizes a request/
response model to set and retrieve data values such as host
identifiers, link utilization metrics, error rates, and counters
between application software on managing and managed devices
[RFC3411]. Data may be directly sampled or consolidated into
representative statistics. Additionally, SNMP supports a model for
unidirectional push notification messages, called event
notifications, based on predefined triggering events.
SNMP managing devices can query agents for status information, send
new configurations, and request to be informed when specific events
have occurred. SNMP devices separate the representations for data
modeling (Structure of Management Information (SMI) [RFC2578] and the
Management Information Base (MIB) [RFC3418]) and messaging,
sequencing and encoding (the SNMP protocol [RFC3411] [RFC3416]).
Separating data models from messaging and encoding is a best practice
in subsequent management protocols and likely necessary for the
DTNMA. In particular, SNMP MIBs provide well-organized, hierarchical
Object Identifiers (OIDs) which support the compressibility necessary
for challenged DTNs.
While there is a large installation base for SNMP, several aspects of
the protocol make it inappropriate for use in a challenged network.
SNMP relies on sessions with low round-trip latency to support its
"pull" mechanism. Complex management can be achieved, but only
through careful orchestration of real-time, end-to-end, managing-
device-generated query-and-response logic.
There is existing work that uses the SNMP data model to support some
low-fidelity Agent-side processing, to include the Distributed
Management Expression MIB [RFC2982] and Definitions of Managed
Objects for the Delegation of Management Scripts [RFC3165]. However,
Agent autonomy is not an SNMP mechanism, so support for a local agent
response to an initiating event is limited. In a challenged network
where the delay between a managing device receiving an alert and
sending a response can be significant, SNMP is insufficient for
autonomous event handling.
Birrane, et al. Expires 25 April 2024 [Page 18]
Internet-Draft DTNMA October 2023
5.2. XML-Based Protocols
Several network management protocols, including NETCONF [RFC6241],
RESTCONF [RFC8040], and CORECONF [I-D.ietf-core-comi], share the same
XML information set [xml-infoset] to describe the abstract data model
necessary to manage the configuration of network devices. Each
protocol, however, provides a different encoding of that XML
information set.
YANG can be used to define the data model semantics and/or model
syntax for the aforementioned network management protocols. YANG
[RFC7950] is a data modeling language used to model the configuration
and state data of managed devices and applications. A number of
network management protocols have been developed around the
definition, exchange, and reporting associated with YANG data models.
Currently, YANG represents the standard for defining network
management information.
5.2.1. The YANG Data Model
The YANG model defines a schema for organizing and accessing a
device's configuration or operational information. Once a model is
developed, it is loaded to both the client and server, and serves as
a contract between the two. A YANG model can be complex, describing
many containers of managed elements, each providing methods for
device configuration or reporting of operational state while
differentiating implied and applied configuration [RFC8342].
The YANG module itself is a flexible data model that could be used
for capturing the autonomy models and other behaviors needed by the
DTNMA. The YANG schema provides flexibility in the organization of
data to the model developer. The YANG schema supports a broad range
of data types noted in [RFC6991]. YANG supports the definition of
parameterized Remote Procedure Calls (RPCs) to be executed on managed
nodes as well as the definition of push notifications within the
model.
The YANG modeling language continues to evolve as new features are
needed by adopting management protocols. Two evolving features that
might be useful in the DTNMA are notifications and schema
identifiers.
* YANG notifications [RFC8639] and YANG-Push notifications [RFC8641]
allow a client to subscribe to the delivery of specific containers
or data nodes defined in the model, either on a periodic or "on
change" basis. These notification events can be filtered
according to XPath [xpath] or subtree [RFC6241] filtering as
described in [RFC8639] Section 2.2.
Birrane, et al. Expires 25 April 2024 [Page 19]
Internet-Draft DTNMA October 2023
* YANG Schema Item iDentifiers (SIDs) [I-D.ietf-core-sid] are
proposed to be 63-bit identifiers used for more efficiently
identification of YANG data elements for use in constrained
environments.
While the YANG model is currently the standard way to describe
management data, there are concerns with its unmodified use in the
DTNMA, as follows.
1. Size. Data nodes within a YANG model are referenced by a
verbose, string-based path of the module, sub-module, container,
and any data nodes such as lists, leaf-lists, or leaves, without
any explicit hierarchical organization based on data or object
type. Existing efforts to make compressed identifies for YANG
objects (such as SIDs) are still relatively verbose (~8 bytes per
item) and do not natively support ways to glob multiple SIDs.
2. Protocol Coupling. A significant amount of existing YANG tooling
presumes the use of YANG with a specific management protocol.
The emergence of multiple NETCONF-derived protocols may make
these presumptions less problematic in the future. Work to more
consistently identify different types of YANG modules and their
use has been undertaken to disambiguate how YANG modules should
be treated [RFC8199].
3. Agent Control. YANG RPCs execute commands on a device and
generate an expected, structured response. RPC execution is
strictly limited to those issued by the client. Commands are
executed immediately and sequentially as they are received by the
server, and there is no method to autonomously execute RPCs
triggered by specific events or conditions.
5.2.2. XML-Based Management Protocols
NETCONF [RFC6241], RESTCONF [RFC8040], and CORECONF
[I-D.ietf-core-comi] each provide the mechanisms to install,
manipulate, and delete the configuration of network devices. These
network management protocols use the same XML information set, but
provide different encodings of the abstract data model it describes.
5.2.2.1. NETCONF
NETCONF is a stateful, XML-based protocol that provides a RPC syntax
to retrieve, edit, copy, or delete any data nodes or exposed
functionality on a server. It requires that underlying transport
protocols support long-lived, reliable, low-latency, sequenced data
delivery sessions.
Birrane, et al. Expires 25 April 2024 [Page 20]
Internet-Draft DTNMA October 2023
NETCONF connections are required to provide authentication, data
integrity, confidentiality, and replay protection through secure
transport protocols such as SSH or TLS. A bi-directional NETCONF
session must be established before any data transfer can occur. All
of these requirements make NETCONF a poor choice for operating in a
challenged network.
5.2.2.2. RESTCONF
RESTCONF is a stateless RESTful protocol based on HTTP. RESTCONF
configures or retrieves individual data elements or containers within
YANG data models by passing JSON over REST. This JSON encoding is
used to GET, POST, PUT, PATCH, or DELETE data nodes within YANG
modules.
RESTCONF is a stateless protocol because it presumes that it is
running over a stateful secure transport (HTTP over TLS). Also,
RESTCONF presumes that a single pull of information can be made in a
single round-trip. In this way, RESTCONF is only stateless between
queries - not internal to a single query.
5.2.2.3. CORECONF
CORECONF is an emerging stateless protocol built atop the Constrained
Application Protocol (CoAP) [RFC7252] that defines a messaging
construct developed to operate specifically on constrained devices
and networks by limiting message size and fragmentation. CoAP also
implements a request/response system and methods for GET, POST, PUT,
and DELETE.
Currently, the CORECONF draft [I-D.ietf-core-comi] is archived and
expired since 2021.
5.3. Autonomic Networking
The future of network operations requires more autonomous behavior
including self-configuration, self-management, self-healing, and
self-optimization. One approach to support this is termed Autonomic
Networking [RFC7575].
In particular, there is a large and growing set of work within the
IETF focused on developing an Autonomic Networking Integrated Model
and Approach (ANIMA). The ANIMA work has developed a comprehensive
reference model for distributing autonomic functions across multiple
nodes in an autonomic networking infrastructure [RFC8993].
Birrane, et al. Expires 25 April 2024 [Page 21]
Internet-Draft DTNMA October 2023
This work, focused on learning the behavior of distributed systems to
predict future events, is an exciting and emerging network management
capability. This includes the development of signalling protocols
such as GRASP [RFC8990] and autonomic control planes [RFC8368].
Both autonomic and challenged networks require similar degrees of
autonomy. However, challenged networks cannot provide the complex
coordination between nodes and distributed supporting infrastructure
necessary for the frequent data exchanges for negotiation, learning,
and bootstrapping associated with the above capabilities.
There is some emerging work in ANIMA as to how disconnected devices
might join and leave the autonomic control plane over time. However,
this work is solving an important, but different, problem than that
encountered by challenged networks.
6. Motivation for New Features
The future of network management will involve autonomous and
autonomic functions operating on both managed and managing devices.
However, the development of distributed autonomy for coordinated
learning and event reaction is different from a managed device
operating without connectivity to a managing node.
Management mechanisms that provide DTNMA desirable properties do not
currently exist. This is not surprising since autonomous management
in the context of a challenged networking environment is an emerging
use case.
In particular, a management architecture is needed that provides the
following new features.
1. Open Loop Control. Freedom from a request-response architecture,
API, or other presumption of timely round-trip communications.
This is particularly important when managing networks that are
not built over an HTTP or TCP/TLS infrastructure.
2. Standard Autonomy Model. An autonomy model that allows for
standard expressions of policy to guarantee deterministic
behavior across devices and vendor implementations.
3. Compressible Model Structure. A data model that allows for very
compact encodings by defining and exploiting common elements of
data schemas.
Birrane, et al. Expires 25 April 2024 [Page 22]
Internet-Draft DTNMA October 2023
Combining these new features with existing mechanisms for message
data exchange (such as BP), data representations (such as CBOR) and
data modeling languages (such as YANG) will form a pragmatic approach
to defining challenged network management.
7. Reference Model
There are a multitude of ways in which both existing and emerging
network management protocols, APIs, and applications can be
integrated for use in challenged environments. However, expressing
the needed behaviors of the DTNMA in the context of any of these pre-
existing elements risks conflating systems requirements, operational
assumptions, and implementation design constraints.
7.1. Important Concepts
This section describes a network management concept for challenged
networks (generally) and those conforming to the DTN architecture (in
particular). The goal of this section is to describe how DTNMA
services provide DTNMA desirable properties.
| NOTE: This section assumes a BPv7 underlying network transport.
| Bundles are the baselined transport protocol data units of the
| DTN architecture. Additionally, they may be used in a variety
| of network architectures beyond the DTN architecture.
| Therefore, assuming bundles is a convenient way of scoping
| DTNMA to any network or network architecture that relies on
| BPv7 features.
Similar to other network management architectures, the DTNMA draws a
logical distinction between a managed device and a managing device.
Managed devices use a DA to manage resident applications. Managing
devices use a DM to both monitor and control DAs.
| NOTE: The terms "managing" and "managed" represent logical
| characteristics of a device and are not, themselves, mutually
| exclusive. For example, a managed device might, itself, also
| manage some other device in the network. Therefore, a device
| may support either or both of these characteristics.
The DTNMA differs from some other management architectures in three
significant ways, all related to the need for a device to self-manage
when disconnected from a managing device.
Birrane, et al. Expires 25 April 2024 [Page 23]
Internet-Draft DTNMA October 2023
1. Pre-shared Definitions. Managing and managed devices should
operate using pre-shared data definitions and models. This
implies that static definitions should be standardized whenever
possible and that managing and managed devices may need to
negotiate definitions during periods of connectivity.
2. Agent Self-Management. A managed device may find itself
disconnected from its managing device. In many challenged
networking scenarios, a managed device may spend the majority of
its time without a regular connection to a managing device. In
these cases, DAs manage themselves by applying pre-shared
policies received from managing devices.
3. Command-Based Interface. Managing devices communicate with
managed devices through a command-based interface. Instead of
exchanging variables, objects, or documents, a managing device
issues commands to be run by a managed device. These commands
may create or update variables, change data stores, or impact the
managed device in ways similar to other network management
approaches. The use of commands is, in part, driven by the need
for DAs to receive updates from both remote management devices
and local autonomy.
7.2. Model Overview
A DTNMA reference model is provided in Figure 1 below. In this
reference model, applications and services on a managing device
communicate with a DM which uses pre-shared definitions to create a
set of policy directives that can be sent to a managed device's DA
via a command-based interface. The DA provides local monitoring and
control (commanding) of the applications and services resident on the
managed device. The DA also performs local data fusion as necessary
to synthesize data products (such as reports) that can be sent back
to the DM when appropriate.
DTNMA Reference Model
Birrane, et al. Expires 25 April 2024 [Page 24]
Internet-Draft DTNMA October 2023
Managed Device Managing Device
+----------------------------+ +-----------------------------+
| +------------------------+ | | +-------------------------+ |
| |Applications & Services | | | | Applications & Services | |
| +----------^-------------+ | | +-----------^-------------+ |
| | | | | |
| +----------v-------------+ | | +-----------v-------------+ |
| | DTNMA +-------------+ | | | | +-----------+ DTNMA | |
| | AGENT | Monitor and | | |Commanding | | | Policy | MANAGER | |
| | | Control | | |<==========| | | Encoding | | |
| | +------+-------------+ | | | | +-----------+-------+ | |
| | |Admin | Data Fusion | | |==========>| | | Reporting | Admin | | |
| | +------+-------------+ | | Reporting | | +-----------+-------+ | |
| +------------------------+ | | +-------------------------+ |
+----------------------------+ +-----------------------------+
^ ^
| Pre-Shared Definitions |
| +---------------------------+ |
+--------| - Autonomy Model |--------+
| - Application Data Models |
| - Runtime Data Stores |
+---------------------------+
Figure 1
This model preserves the familiar concept of "managers" resident on
managing devices and "agents" resident on managed devices. However,
the DTNMA model is unique in how the DM and DA operate. The DM is
used to pre-configure DAs in the network with management policies.
it is expected that the DAs, themselves, perform monitoring and
control functions on their own. In this way, a properly configured
DA may operate without a timely, reliable connection back to a DM.
7.3. Functional Elements
The reference model illustrated in Figure 1 implies the existence of
certain logical elements whose roles and responsibilities are
discussed in this section.
7.3.1. Managed Applications and Services
By definition, managed applications and services reside on a managed
device. These software entities can be controlled through some
interface by the DA and their state can be sampled as part of
periodic monitoring. It is presumed that the DA on the managed
device has the proper data model, control interface, and permissions
to alter the configuration and behavior of these software
applications.
Birrane, et al. Expires 25 April 2024 [Page 25]
Internet-Draft DTNMA October 2023
7.3.2. DTNMA Agent (DA)
A DA resides on a managed device. As is the case with other network
management approaches, this agent is responsible for the monitoring
and control of the applications local to that device. Unlike other
network management approaches, the agent accomplishes this task
without a regular connection to a DTNMA Manager.
The DA performs three major functions on a managed device: the
monitoring and control of local applications, production of data
analytics, and the administrative control of the agent itself.
7.3.2.1. Monitoring and Control
DAs monitor the status of applications running on their managed
device and selectively control those applications as a function of
that monitoring. The following components are used to perform
monitoring and control on an agent.
Rules Database
Each DA maintains a database of policy expressions that form
rules of behavior of the managed device. Within this
database, each rule of behavior is a tuple of a stimulus and
a response. Within the DTNMA, these rules are the embodiment
of policy expressions received from DMs and evaluated at
regular intervals by the autonomy engine. The rules database
is the collection of active rules known to the DA.
Autonomy Engine
The DA autonomy engine monitors the state of the managed
device looking for pre-defined stimuli and, when encountered,
issuing a pre-defined response. To the extent that this
function is driven by the rules database, this engine acts as
a policy execution engine. This engine may also be directly
configured by managers during periods of connectivity for
actions separate from those in the rules database (such as
enabling or disabling sets of rules). Once configured, the
engine may function without other access to any managing
device. This engine may also reconfigure itself as a
function of policy.
Application Control Interfaces
DAs must support control interfaces for all managed
applications. Control interfaces are used to alter the
configuration and behavior of an application. These
interfaces may be custom for each application, or as provided
through a common framework such as provided by an operating
system.
Birrane, et al. Expires 25 April 2024 [Page 26]
Internet-Draft DTNMA October 2023
7.3.2.2. Data Fusion
DAs generate new data elements as a function of the current state of
the managed device and its applications. These new data products may
take the form of individual data values, or new collections of data
used for reporting. The logical components responsible for these
behaviors are as follows.
Application Data Interfaces
DAs must support mechanisms by which important state is
retrieved from various applications resident on the managed
device. These data interfaces may be custom for each
application, or as provided through a common framework such
as provided by an operating system.
Data Value Generators
DAs may support the generation of new data values as a
function of other values collected from the managed device.
These data generators may be configured with descriptions of
data values and the data values they generate may be included
in the overall monitoring and reporting associated with the
managed device.
Report Generators
DAs may, as appropriate, generate collections of data values
for transmission to managers. Reports can be generated as a
matter of policy or in response to the handling of critical
events (such as errors), or other logging needs. The
generation of a report is independent of whether there exists
any connectivity between a DA and a DM. It is assumed that
reports are queued on an agent pending transmit
opportunities.
7.3.2.3. Administration
DAs must perform a variety of administrative services in support of
their configuration. The significant such administrative services
are as follows.
Manager Mapping
The DTNMA allows for a many-to-many relationship amongst
DTNMA Agents and Managers. A single DM may configure
multiple DAs, and a single DA may be configured by multiple
DMs. Multiple managers may exist in a network for at least
two reasons. First, different managers may exist to control
different applications on a device. Second, multiple
managers increase the likelihood of an agent encountering a
manager when operating in a sparse or challenged environment.
Birrane, et al. Expires 25 April 2024 [Page 27]
Internet-Draft DTNMA October 2023
While the need for multiple managers is required for
operating in a dynamically partitioned network, this
situation allows for the possibility of conflicting
information from different managers. Implementations of the
DTNMA should consider conflict resolution mechanisms. Such
mechanisms might include analyzing managed content, time,
agent location, or other relevant information to select one
manager input over other manager inputs.
Data Verifiers
DAs might handle large amounts of data produced by various
sources, to include data from local managed applications,
remote managers, and self-calculated values. DAs should
ensure, when possible, that externally generated data values
have the proper syntax (e.g., data type and ranges) and any
required integrity and confidentiality.
Access Controllers
DAs support authorized access to the management of individual
applications, to include the administrative management of the
agent itself. This means that a manager may only set policy
on the agent pursuant to verifying that the manager is
authorized to do so.
7.3.3. Managing Applications and Services
Managing applications and services reside on a managing device and
serve as the both the source of DA policy statements and the target
of DA reporting. They may operate with or without an operator in the
loop.
Unlike management applications in unchallenged networks, these
applications cannot exert timely closed-loop control over any managed
device application. Instead, these applications must be built to
exercise open-loop control by producing policies that can be
configured and enforced on managed devices by DAs.
| NOTE: Closed-loop control in this context refers to the
| practice of waiting for a response from a managed device prior
| to issuing new commands to that device. These "loops" may be
| closed quickly (in milliseconds) or over much longer periods
| (hours, days, years). The alternative to closed-loop control
| is open-loop control, where responses from a managed device and
| commands to the managed device are independent of one another.
Birrane, et al. Expires 25 April 2024 [Page 28]
Internet-Draft DTNMA October 2023
7.3.4. DTNMA Manager (DM)
A DM resides on a managing device. This manager provides an
interface between various managing applications and services and the
DAs that enforce their policies. In providing this interface, DMs
translate between whatever native interface exists to various
managing applications and the autonomy models used to encode
management policy.
The DM performs three major functions on a managing device: policy
encoding, reporting, and administration.
7.3.4.1. Policy Encoding
DMs translate policy directives from managing applications and
services into standardized policy expressions that can be recognized
by DAs. The following logical components are used to perform this
policy encoding.
Application Control Interfaces
DMs must support control interfaces for managing
applications. These control interfaces are used to receive
desired policy statements from applications. These
interfaces may be custom for each application, or provided
through a common framework, protocol, or operating system.
Policy Encoders
DAs implement a standardized autonomy model comprising
standardized data elements. The open-loop control structures
provided by managing applications must be represented in this
common language. Policy encoders perform this encoding
function.
Policy Aggregators
DMs collect multiple encoded policies into messages that can
be sent to DAs over the network. This implies the proper
addressing of agents and the creation of messages that
support store-and-forward operations. It is recommended that
control messages be packaged using BP bundles when there may
be intermittent connectivity between DMs and DAs.
7.3.4.2. Reporting
DMs receive reports on the status of managed devices during periods
of connectivity with the DAs on those devices. The following logical
components are needed to implement reporting capabilities on a DM.
Birrane, et al. Expires 25 April 2024 [Page 29]
Internet-Draft DTNMA October 2023
Report Collectors
DMs receive reports from DAs in an asynchronous manner. This
means that reports may be received out of chronological order
and in ways that are difficult or impossible to associate
with a specific policy from a managing application. DMs
collect these reports and extract their data in support of
subsequent data analytics.
Data Analyzers
DMs review sets of data reports from DAs with the purpose of
extracting relevant data to communicate with managing
applications. This may include simple data extraction or may
include more complex processing such as data conversion, data
fusion, and appropriate data analytics.
Application Data Interfaces
DMs must support mechanisms by which data retrieved from
agent may be provided back to managing devices. These
interfaces may be custom for each application, or as provided
through a common framework, protocol, or operating system.
7.3.4.3. Administration
Managers in the DTNMA must perform a variety of administrative
services in support of their proper configuration and operation.
This includes the following logical components.
Agent Mappings
The DTNMA allows DMs to communicate with multiple DAs.
However, not every agent in a network is expected to support
the same set of Application Data Models or otherwise have the
same set of managed applications running. For this reason,
DMs must determine individual DA capabilities to ensure that
only appropriate controls are sent to a DA.
Data Verifiers
DMs handle large amounts of data produced by various sources,
to include data from managing applications and DAs. DMs
should ensure, when possible, that data values received from
DAs over a network have the proper syntax (e.g., data type
and ranges) and any required integrity and confidentiality.
Access Controllers
DMs should only send controls to agents when the manager is
configured with appropriate access to both the agent and the
applications being managed.
Birrane, et al. Expires 25 April 2024 [Page 30]
Internet-Draft DTNMA October 2023
7.3.5. Pre-Shared Definitions
A consequence of operating in a challenged environment is the
potential inability to negotiate information in real-time. For this
reason, the DTNMA requires that managed and managing devices operate
using pre-shared definitions rather than relying on data definition
negotiation.
The three types of pre-shared definitions in the DTNMA are the DA
autonomy model, managed application data models, and any runtime data
shared by managers and agents.
Autonomy Model
A DTNMA autonomy model represents the data elements and
associated autonomy structures that define the behavior of
the agent autonomy engine. A standardized autonomy model
allows for individual implementations of DAs, and DMs to
interoperate. A standardized model also provides guidance to
the design and implementation of both managed and managing
applications.
Application Data Models
As with other network management architectures, the DTNMA
pre-supposes that managed applications (and services) define
their own data models. These data models include the data
produced by, and controls implemented by, the application.
These models are expected to be static for individual
applications and standardized for applications implementing
standard protocols.
Runtime Data Stores
Runtime data stores, by definition, include data that is
defined at runtime. As such, the data is not pre-shared
prior to the deployment of DMs and DAs. Pre-sharing in this
context means that DMs and DAs are able to define and
synchronize data elements prior to their operational use in
the system. This synchronization happens during periods of
connectivity between DMs and DAs.
8. Desired Services
This section provides a description of the services provided by DTNMA
elements on both managing and managed devices. These service
descriptions differ from other management descriptions because of the
unique characteristics of the DTNMA operating environment.
Birrane, et al. Expires 25 April 2024 [Page 31]
Internet-Draft DTNMA October 2023
| Predicate autonomy, asynchronous data transport, and
| intermittent connectivity require new techniques for device
| management. Many of the services discussed in this section
| attempt to provide continuous operation of a managed device
| through periods of no connectivity.
8.1. Local Monitoring and Control
DTNMA monitoring is associated with the agent autonomy engine. The
term monitoring implies timely and regular access to information such
that state changes may be acted upon within some response time
period. Within the DTNMA, connections between a managed and managing
device are unable to provide such a connection and, thus, monitoring
functions must be handled on the managed device.
Predicate autonomy on a managed device should collect state
associated with the device at regular intervals and evaluate that
collected state for any changes that require a preventative or
corrective action. Similarly, this monitoring may cause the device
to generate one or more reports destined to the managing device.
Similar to monitoring, DTNMA control results in actions by the agent
to change the state or behavior of the managed device. All control
in the DTNMA is local control. In cases where there exists a timely
connection to a manager, received controls are still run through the
autonomy engine. In this case, the stimulus is the direct receipt of
the control and the response is to immediately run the control. In
this way, there is never a dependency on a session or other stateful
exchange with any remote entity.
8.2. Local Data Fusion
DTNMA Fusion services produce new data products from existing state
on the managed device. These fusion products can be anything from
simple summations of sampled counters to complex calculations of
behavior over time.
Fusion is an important service in the DTNMA because fusion products
are part of the overall state of a managed device. Complete
knowledge of this overall state is important for the management of
the device, particularly in a stimulus-response system whose stimuli
are evaluated against this state. In particular, the predicates of
rules on a DA may refer to fused data.
Birrane, et al. Expires 25 April 2024 [Page 32]
Internet-Draft DTNMA October 2023
In-situ data fusion is an important function as it allows for the
construction of intermediate summary data, the reduction of stored
and transmitted raw data, possibly fewer predicates in rule
definitions, and otherwise insulates the data source from conclusions
drawn from that data.
While some fusion is performed in any management system, the DTNMA
requires fusion to occur on the managed device itself. If the
network is partitioned such that no connection to a managing device
is available, fusion must happen locally. Similarly, connections to
a managing device might not remain active long enough for round-trip
data exchange or may not have the bandwidth to send all sampled data.
| NOTE: While data fusion is an important function within the
| DTNMA, it is expected that the storage and transmission of raw
| (or pre-fused) data remains a capability of the system. In
| particular, raw data can be useful for debugging managed
| devices, understanding complex interactions and underlying
| conditions, and tuning for better performance and/or better
| outcomes.
8.3. Remote Configuration
DTNMA configuration services must update the local configuration of a
managed device with the intent to impact the behavior and
capabilities of that device. The change of device configurations is
a common service provided by many network management systems. The
DTNMA has a unique approach to configuration for the following
reasons.
The DTNMA configuration service is unique in that the selection of
managed device configurations must occur, itself, as a function of
the state of the device. This implies that management proxies on the
device store multiple configuration functions that can be applied as
needed without consultation from a managing device.
| This approach differs from the management concept of selecting
| from multiple datastores in that DTNMA configuration functions
| can target individual data elements and can calculate new
| values from local device state.
When detecting stimuli, the agent autonomy engine must support a
mechanism for evaluating whether application monitoring data or
runtime data values are recent enough to indicate a change of state.
In cases where data has not been updated recently, it may be
considered stale and not used to reliably indicate that some stimulus
has occurred.
Birrane, et al. Expires 25 April 2024 [Page 33]
Internet-Draft DTNMA October 2023
8.4. Remote Reporting
DTNMA reporting services collect information known to the managed
device and prepare it for eventual transmission to one or more
managing devices. The contents of these reports, and the frequency
at which they are generated, occurs as a function of the state of the
managed device, independent of the managing device.
Once generated, it is expected that reports might be queued pending a
connection back to a managing device. Therefore, reports must be
differentiable as a function of the time they were generated.
When reports are sent to a managing device over a challenged network,
they may arrive out of order due to taking different paths through
the network or being delayed due to retransmissions. A managing
device should not infer meaning from the order in which reports are
received, nor should a given report be associated with a specific
control or autonomy action on a given managed device.
8.5. Authorization
Both local and remote services provided by the DTNMA affect the
behavior of multiple applications on a managed device and may
interface with multiple managing devices. It is expected that
transport protocols used in any DTNMA implementation support security
services such as integrity and confidentiality.
Authorization services enforce the potentially complex mapping of
other DTNMA services amongst managed and managing devices in the
network. For example, fine-grained access control can determine
which managing devices receive which reports, and what controls can
be used to alter which managed applications.
This is particularly beneficial in networks that either deal with
multiple administrative entities or overlay networks that cross
administrative boundaries. Allowlists, blocklists, key-based
infrastructures, or other schemes may be used for this purpose.
9. Logical Autonomy Model
An important characteristic of the DTNMA is the shift in the role of
a managing device. In the DTNMA, managers configure the autonomy
engines on agents, and it is the agents that provide local device
management. One way to describe the behavior of the agent autonomy
engine is to describe the characteristics of the autonomy model it
implements.
Birrane, et al. Expires 25 April 2024 [Page 34]
Internet-Draft DTNMA October 2023
This section describes a logical autonomy model in terms of the
abstract data elements that would comprise the model. Defining
abstract data elements allows for an unambiguous discussion of the
behavior of an autonomy model without mandating a particular design,
encoding, or transport associated with that model.
9.1. Overview
Managing autonomy on a potentially disconnected device must behave in
both an expressive and deterministic way. Expressivity allows for
the model to be configured for a wide range of future situations.
Determinism allows for the forensic reconstruction of device behavior
as part of debugging or recovery efforts.
| NOTE: The use of predicate logic and a stimulus-response system
| does not conflict with the use of higher-level autonomous
| function or the incorporation of machine learning. The DTNMA
| recommended autonomy model allows for the use of higher levels
| of autonomous function as moderated and controlled by a more
| deterministic base autonomy system.
|
| By allowing for a multi-tier autonomy system, the DTNMA may
| increase the adoption of higher-functioning autonomy because of
| the reporting, control, and determinism of the underlying
| predicate system.
The DTNMA autonomy model is a rule-based model in which individual
rules associate a pre-identified stimulus with a pre-configured
response to that stimulus.
Stimuli are identified using one or more predicate logic expressions
that examine aspects of the state of the managed device. Responses
are implemented by running one or more procedures on the managed
device.
In its simplest form, a stimulus is a single predicate expression of
a condition that examines some aspect of the state of the managed
device. When the condition is met, a predetermined response is
applied. This behavior can be captured using the construct:
IF <condition 1> THEN <response 1>;
Birrane, et al. Expires 25 April 2024 [Page 35]
Internet-Draft DTNMA October 2023
In more complex forms, a stimulus may include both a common condition
shared by multiple rules and a specific condition for each individual
rule. If the common condition is not met, the evaluation of the
specific condition of each rule sharing the common condition can be
skipped. In this way, the total number of predicate evaluations can
be reduced. This behavior can be captured using the construct:
IF <common condition> THEN
IF <specific condition 1> THEN <response 1>
IF <specific condition 2> THEN <response 2>
IF <specific condition 3> THEN <response 3>
| NOTE: The DTNMA model remains a stimulus-response system,
| regardless of whether a common condition is part of the
| stimulus. However, it is recommended that implementations
| incorporate a common condition because of the efficiency
| provided by such a bulk evaluation.
|
| NOTE: One use of a stimulus "common condition" is to associated
| the condition with an on-board event such as the expiring of a
| timer or the changing of a monitored value.
|
| NOTE: The DTNMA does not prescribe when rule stimuli must be
| evaluated. Implementations may choose to evaluate rule stimuli
| at periodic intervals (such as 1Hz or 100Hz). When stimuli
| include on-board events, implementations may choose to perform
| an immediate evaluation at the time of the event rather than
| waiting for a periodic evaluation.
DTNMA Autonomy Model
Birrane, et al. Expires 25 April 2024 [Page 36]
Internet-Draft DTNMA October 2023
Managed Applications | DTNMA Agent | DTNMA Manager
+---------------------+--------------------------------+--------------+
| +---------+ |
| | Local | | Encoded
| | Rule DB |<-------------------- Policy
| +---------+ | Expressions
| ^ |
| | |
| v |
| +----------+ +---------+ |
Monitoring Data------>| Agent | | Runtime | |
| | Autonomy |<-->| Data |<---- Definitions
Application Control<------| Engine | | Store | |
| +----------+ +---------+ |
| | |
| +-------------------------> Reports
| |
Figure 2
The flow of data into and out of the agent autonomy engine is
illustrated in Figure 2. In this model, the autonomy engine stores
the combination of stimulus conditions and associated responses as a
set of "rules" in a rules database. This database is updated through
the execution of the autonomy engine and as configured from policy
statements received by managers.
Stimuli are detected by examining the state of applications as
reported through application monitoring interfaces and through any
locally-derived data. Local data is calculated in accordance with
definitions also provided by managers as part of the runtime data
store.
Responses to stimuli are run as updated to the rules database,
updated to the runtime data store, controls sent to applications, and
the generation of reports.
9.2. Model Characteristics
There are several practical challenges to the implementation of a
distributed rule-based system. Large numbers of rules may be
difficult to understand, deconflict, and debug. Rules whose
conditions are given by fused or other dynamic data may require data
logging and reporting for deterministic offline analysis. Rule
differences across managed devices may lead to oscillating effects.
This section identifies those characteristics of an autonomy model
that might help implementations mitigate some of these challenges.
Birrane, et al. Expires 25 April 2024 [Page 37]
Internet-Draft DTNMA October 2023
There are a number of ways to represent data values, and many data
modeling languages exist for this purpose. When considering how to
model data in the context of the DTNMA autonomy model there are some
modeling features that should be present to enable functionality.
There are also some modeling features that should be prevented to
avoid ambiguity.
Traditional network management approaches favor flexibility in their
data models. The DTNMA stresses deterministic behavior that supports
forensic analysis of agent activities "after the fact". As such, the
following statements should be true of all data representations
relating to DTNMA autonomy.
* Strong Typing - The predicates and expressions that comprise the
autonomy services in the DTNMA should require strict data typing.
This avoids errors associated with implicit data conversions and
helps detect misconfiguration.
* Acyclic Dependency - Many dependencies exist in an autonomy model,
particularly when combining individual expressions or results to
create complex behaviors. Implementations that conform to the
DTNMA must prevent circular dependencies.
* Fresh Data - Autonomy models operating on data values presume that
their data inputs represent the actionable state of the managed
device. If a data value has failed to be refreshed within a time
period, autonomy might incorrectly infer an operational state.
Regardless of whether a data value has changed, DTNMA
implementations must provide some indicator of whether the data
value is "fresh" meaning that is still represents the current
state of the device.
* Pervasive Parameterization - Where possible, autonomy model
objects should support parameterization to allow for flexibility
in the specification. Parameterization allows for the definition
of fewer unique model objects and also can support the
substitution of local device state when exercising device control
or data reporting.
* Configurable Cardinality - The number of data values that can be
supported in a given implementation is finite. For devices
operating in challenged environments, the number of supported
objects may be far fewer than that which can be supported by
devices in well-resourced environments. DTNMA implementations
should define limits to the number of supported objects that can
be active in a system at one time, as a function of the resources
available to the implementation.
Birrane, et al. Expires 25 April 2024 [Page 38]
Internet-Draft DTNMA October 2023
* Control-Based Updates - The agent autonomy engine changes the
state of the managed device by running controls on the device.
This is different from other approaches where the behavior of a
managed device is updated only by updated configuration values,
such as in a table or datastore. Altering behavior via one or
more controls allows checking all pre-conditions before making
changes as well as providing more granularity in the way in which
the device is updated. Where necessary, controls can be defined
to perform bulk updated of configuration data so as not to lose
that update modality.
9.3. Data Value Representation
The expressive representation of simple data values is fundamental to
the successful construction and evaluation of predicates in the DTNMA
autonomy model. When defining such values, there are useful
distinctions regarding how values are identified and whether values
are generated internal or external to the autonomy model.
A DTNMA data value should combine a base type (e.g., integer, real,
string) representation with relevant semantic information. Base
types are used for proper storage and encoding. Semantic information
allows for additional typing, constraint definitions, and mnemonic
naming. This expanded definition of data value allows for better
predicate construction and evaluation, early type checking, and other
uses.
Data values may further be annotated based on whether their value is
the result of a DA calculation or the result of some external process
on the managed device. For example, operators may with to know which
values can be updated by actions on the DA versus which values (such
as sensor readings) cannot be reliably changed because they are
calculated external to the DA.
9.4. Data Reporting
The DTNMA autonomy model should, as required, report on the state of
its managed device (to include the state of the model itself). This
reporting should be done as a function of the changing state of the
managed device, independent of the connection to any managing device.
Queuing reports allows for later forensic analysis of device
behavior, which is a desirable property of DTNMA management.
DTNMA data reporting consists of the production of some data report
instance conforming to a data report schema. The use of schemas
allows a report instance to identify the schema to which it conforms
in lieu of carry that structure in the instance itself. This
approach can significantly reduce the size of generated reports.
Birrane, et al. Expires 25 April 2024 [Page 39]
Internet-Draft DTNMA October 2023
| NOTE: The DTNMA data reporting concept is intentionally
| distinct from the concept of exchanging data stores across a
| network. It is envisioned that a DA might generate a data
| report instance of a data report schema at regular intervals or
| in response to local events. In this model, many report
| schemas may be defined to capture unique, relevant combinations
| of known data values rather than sending bulk data stores off-
| platform for analysis.
|
| NOTE: It is not required that data report schemas be tabular in
| nature. Individual implementations might define tabular
| schemas for table-like data and other report schemas for more
| heterogeneous reporting.
9.5. Command Execution
The agent autonomy engine requires that managed devices issue
commands on themselves as if they were otherwise being controlled by
a managing device. The DTNMA implements commanding through the use
of controls and macros.
Controls represent parameterized, predefined procedures run by the DA
either as directed by the DM or as part of a rule response from the
DA autonomy engine. Controls are conceptually similar to RPCs in
that they represent parameterized functions run on the managed
device. However, they are conceptually dissimilar from RPCs in that
they do not have a concept of a return code as they must operate over
an asynchronous transport. The concept of return code in an RPC
implies a synchronous relationship between the caller of the
procedure and the procedure being called, which might not be possible
within the DTNMA.
The success or failure of a control may be handled locally by the
agent autonomy engine. Otherwise, the externally observable impact
of a control can be understood through the generation and eventual
examination of data reports produced by the managed device.
Macros represent ordered sequences of controls.
| NOTE: The use of the term Control in the DTNMA is derived in
| part from the concept of Command and Control (C2) where control
| implies the operational instructions that must be undertaken to
| implement (or maintain) a commanded objective. The DA autonomy
| engine controls a managed device to allow it to fulfill some
| purpose as commanded by a (possibly disconnected) managing
| device.
|
Birrane, et al. Expires 25 April 2024 [Page 40]
Internet-Draft DTNMA October 2023
| For example, attempting to maintain a safe internal thermal
| environment for a spacecraft is considered "thermal control"
| (not "thermal commanding") even though thermal control involves
| sending commands to heaters, louvers, radiators, and other
| temperature-affecting components.
|
| Even when CTRLs are received from a managing device with the
| intent to be run immediately, the control-vs-command
| distinction still applies. The CTRL run on the managed device
| is in service of the command received from the managing device
| to immediately change the local state of the device.
9.6. Predicate Autonomy Rules
As discussed in Section 9.1, the DTNMA rule-based stimulus-response
system associates stimulus detection with a predetermined response.
Rules may be categorized based on whether their stimuli include
generic statements of managed device state or whether they are
optimized to only consider the passage of time on the device.
State-based rules are those whose stimulus is based on the evaluated
state of the managed device. Time-based rules are a unique subset of
state-based rules whose stimulus is given only by a time-based event.
Implementations might create different structures and evaluation
mechanisms for these two different types of rules to achieve more
efficient processing on a platform.
10. Use Cases
Using the autonomy model mnemonics defined in Section 9, this section
describes flows through sample configurations conforming to the
DTNMA. These use cases illustrate remote configuration, local
monitoring and control, multiple manager support, and data fusion.
10.1. Notation
The use cases presented in this section are documented with a
shorthand notation to describe the types of data sent between
managers and agents. This notation, outlined in Table 1, leverages
the mnemonic definitions of autonomy model elements defined in
Section 9.
Birrane, et al. Expires 25 April 2024 [Page 41]
Internet-Draft DTNMA October 2023
+==================+===================================+===========+
| Term | Definition | Example |
+==================+===================================+===========+
| EDD# | Externally Defined Data - a data | EDD1, |
| | value defined external to the DA. | EDD2 |
+------------------+-----------------------------------+-----------+
| V# | Variable - a data value defined | V1 = EDD1 |
| | internal to the DA. | + 7 |
+------------------+-----------------------------------+-----------+
| EXPR | Predicate expression - used to | V1 > 5 |
| | define a rule stimulus. | |
+------------------+-----------------------------------+-----------+
| ID | DTNMA Object Identifier. | V1, EDD2 |
+------------------+-----------------------------------+-----------+
| ACL# | Enumerated Access Control List. | ACL1 |
+------------------+-----------------------------------+-----------+
| DEF(ACL,ID,EXPR) | Define ID from expression. Allow | DEF(ACL1, |
| | managers in ACL to see this ID. | V1, EDD1 |
| | | + EDD2) |
+------------------+-----------------------------------+-----------+
| PROD(P,ID) | Produce ID according to predicate | PROD(1s, |
| | P. P may be a time period (1s) | EDD1) |
| | or an expression (EDD1 > 10). | |
+------------------+-----------------------------------+-----------+
| RPT(ID) | A report instance containing data | RPT(EDD1) |
| | named ID. | |
+------------------+-----------------------------------+-----------+
Table 1: Terminology
These notations do not imply any implementation approach. They only
provide a succinct syntax for expressing the data flows in the use
case diagrams in the remainder of this section.
10.2. Serialized Management
This nominal configuration shows a single DM interacting with
multiple DAs. The control flows for this scenario are outlined in
Figure 3.
Serialized Management Control Flow
Birrane, et al. Expires 25 April 2024 [Page 42]
Internet-Draft DTNMA October 2023
+-----------+ +---------+ +---------+
| DTNMA | | DTNMA | | DTNMA |
| Manager A | | Agent A | | Agent B |
+----+------+ +----+----+ +----+----+
| | |
|-----PROD(1s, EDD1)--->| | (1)
|----------------------------PROD(1s, EDD1)-->|
| | |
| | |
|<-------RPT(EDD1)------| | (2)
|<----------------------------RPT(EDD1)-------|
| | |
| | |
|<-------RPT(EDD1)------| |
|<----------------------------RPT(EDD1)-------|
| | |
| | |
|<-------RPT(EDD1)------| |
|<----------------------------RPT(EDD1)-------|
| | |
Figure 3
In a serialized management scenario, a single DM interacts with
multiple DAs.
In this figure, the DTNMA Manager A sends a policy to DTNMA Agents A
and B to report the value of an EDD (EDD1) every second in (step 1).
Each DA receives this policy and configures their respective autonomy
engines for this production. Thereafter, (step 2) each DA produces a
report containing data element EDD1 and sends those reports back to
the DM.
This behavior continues without any additional communications from
the DM and without requiring a connection between the DA and DM.
10.3. Intermittent Connectivity
Building from the nominal configuration in Section 10.2, this
scenario shows a challenged network in which connectivity between
DTNMA Agent B and the DM is temporarily lost. Control flows for this
case are outlined in Figure 4.
Challenged Management Control Flow
Birrane, et al. Expires 25 April 2024 [Page 43]
Internet-Draft DTNMA October 2023
+-----------+ +---------+ +---------+
| DTNMA | | DTNMA | | DTNMA |
| Manager A | | Agent A | | Agent B |
+----+------+ +----+----+ +----+----+
| | |
|-----PROD(1s, EDD1)--->| | (1)
|----------------------------PROD(1s, EDD1)-->|
| | |
| | |
|<-------RPT(EDD1)------| | (2)
|<----------------------------RPT(EDD1)-------|
| | |
| | |
|<-------RPT(EDD1)------| |
|<----------------------------RPT(EDD1)-------|
| | |
| | |
|<-------RPT(EDD1)------| |
| | RPT(EDD1)| (3)
| | |
| | |
|<-------RPT(EDD1)------| |
| | RPT(EDD1)| (4)
| | |
| | |
|<-------RPT(EDD1)------| |
|<----------------RPT(EDD1), RPT(EDD1)--------| (5)
| | |
Figure 4
In a challenged network, DAs store reports pending a transmit
opportunity.
In this figure, DTNMA Manager A sends a policy to DTNMA Agents A and
B to produce an EDD (EDD1) every second in (step 1). Each DA
receives this policy and configures their respective autonomy engines
for this production. Produced reports are transmitted when there is
connectivity between the DA and DM (step 2).
At some point, DTNMA Agent B loses the ability to transmit in the
network (steps 3 and 4). During this time period, DA B continues to
produce reports, but they are queued for transmission. This queuing
might be done by the DA itself or by a supporting transport such as
BP. Eventually, DTNMA Agent B is able to transmit in the network
again (step 5) and all queued reports are sent at that time. DTNMA
Agent A maintains connectivity with the DM during steps 3-5, and
continues to send reports as they are generated.
Birrane, et al. Expires 25 April 2024 [Page 44]
Internet-Draft DTNMA October 2023
10.4. Open-Loop Reporting
This scenario illustrates the DTNMA open-loop control paradigm, where
DAs manage themselves in accordance with policies provided by DMs,
and provide reports to DMs based on these policies.
The control flow shown in Figure 5, includes an example of data
fusion, where multiple policies configured by a DM result in a single
report from a DA.
Consolidated Management Control Flow
+-----------+ +---------+ +---------+
| DTNMA | | DTNMA | | DTNMA |
| Manager A | | Agent A | | Agent B |
+----+------+ +----+----+ +----+----+
| | |
|-----PROD(1s, EDD1)--->| | (1)
|----------------------------PROD(1s, EDD1)-->|
| | |
| | |
|<-------RPT(EDD1)------| | (2)
|<----------------------------RPT(EDD1)-------|
| | |
| | |
|----------------------------PROD(1s, EDD2)-->| (3)
| | |
| | |
|<-------RPT(EDD1)------| |
|<--------------------------RPT(EDD1,EDD2)----| (4)
| | |
| | |
|<-------RPT(EDD1)------| |
|<--------------------------RPT(EDD1,EDD2)----|
| | |
Figure 5
A many-to-one mapping between management policy and device state
reporting is supported by the DTNMA.
In this figure, DTNMA Manager A sends a policy statement in the form
of a rule to DTNMA Agents A and B, which instructs the DAs to produce
a report with EDD1 every second (step 1). Each DA receives this
policy, which is stored in its respective Rule Database, and
configures its Autonomy Engine. Reports are transmitted by each DA
when produced (step 2).
Birrane, et al. Expires 25 April 2024 [Page 45]
Internet-Draft DTNMA October 2023
At a later time, DTNMA Manager A sends an additional policy to DTNMA
Agent B, requesting the production of a report for EDD2 every second
(step 3). This policy is added to DTNMA Agent B's Rule Database.
Following this policy update, DTNMA Agent A will continue to produce
EDD1 and DTNMA Agent B will produce both EDD1 and EDD2 (step 4).
However, DTNMA Agent B may provide these values to the DM in a single
report rather than as 2 independent reports. In this way, there is
no direct mapping between the single consolidated report sent by
DTNMA Agent B (step 4) and the two different policies sent to DTNMA
Agent B that caused that report to be generated (steps 1 and 3).
10.5. Multiple Administrative Domains
The managed applications on a DA may be controlled by different
administrative entities in a network. The DTNMA allows DAs to
communicate with multiple DMs in the network, such as in cases where
there is one DM per administrative domain.
Whenever a DM sends a policy expression to a DA, that policy
expression may be associated with authorization information. One
method of representing this is an ACL.
| The use of an ACL in this use case does not imply the DTNMA
| requires ACLs to annotate policy expressions. Further, the
| inclusion of ACLs in the policy expressions themselves is for
| representation purposes only, as ACLs are internal to DAs and
| not supplied explicitly in messaging. ACLs and their
| representation in this context are for example purposes only.
The ability of one DM to access the results of policy expressions
configured by some other DM will be limited to the authorization
annotations of those policy expressions.
An example of multi-manager authorization is illustrated in Figure 6.
Multiplexed Management Control Flow
Birrane, et al. Expires 25 April 2024 [Page 46]
Internet-Draft DTNMA October 2023
+-----------+ +---------+ +-----------+
| DTNMA | | DTNMA | | DTNMA |
| Manager A | | Agent A | | Manager B |
+-----+-----+ +----+----+ +-----+-----+
| | |
|---DEF(ACL1,V1,EDD1*2)--->|<---DEF(ACL2, V2, EDD2*2)---| (1)
| | |
|---PROD(1s, V1)---------->|<---PROD(1s, V2)------------| (2)
| | |
|<--------RPT(V1)----------| | (3)
| |--------RPT(V2)------------>|
|<--------RPT(V1)----------| |
| |--------RPT(V2)------------>|
| | |
| |<---PROD(1s, V1)------------| (4)
| | |
| |----ERR(V1 no perm.)------->|
| | |
|--DEF(NULL,V3,EDD3*3)---->| | (5)
| | |
|---PROD(1s, V3)---------->| | (6)
| | |
| |<----PROD(1s, V3)-----------|
| | |
|<--------RPT(V3)----------|--------RPT(V3)------------>| (7)
|<--------RPT(V1)----------| |
| |--------RPT(V2)------------>|
|<-------RPT(V3)-----------|--------RPT(V3)------------>|
|<-------RPT(V1)-----------| |
| |--------RPT(V2)------------>|
Figure 6
Multiple DMs may interface with a single DA, particularly in complex
networks.
In this figure, both DTNMA Managers A and B send policies to DTNMA
Agent A (step 1). DM A defines a variable (V1) whose value is given
by the mathematical expression (EDD1 * 2) and is associated with an
ACL (ACL1) that restricts access to V1 to DM A only. Similarly, DM B
defines a variable (V2) whose value is given by the mathematical
expression (EDD2 * 2) and associated with an ACL (ACL2) that
restricts access to V2 to DM B only.
Birrane, et al. Expires 25 April 2024 [Page 47]
Internet-Draft DTNMA October 2023
Both DTNMA Managers A and B also send policies to DTNMA Agent A to
report on the values of their variables at 1 second intervals (step
2). Since DM A can access V1 and DM B can access V2, there is no
authorization issue with these policies and they are both accepted by
the autonomy engine on Agent A. Agent A produces reports as
expected, sending them to their respective managers (step 3).
Later (step 4) DM B attempts to configure DA A to also report to it
the value of V1. Since DM B does not have authorization to view this
variable, DA A does not include this in the configuration of its
autonomy engine and, instead, some indication of permission error is
included in any regular reporting back to DM B.
DM A also sends a policy to Agent A (step 5) that defines a variable
(V3) whose value is given by the mathematical expression (EDD3 * 3)
and is not associated with an ACL, indicating that any DM can access
V3. In this instance, both DM A and DM B can then send policies to
DA A to report the value of V3 (step 6). Since there is no
authorization restriction on V3, these policies are accepted by the
autonomy engine on Agent A and reports are sent to both DM A and B
over time (step 7).
10.6. Cascading Management
There are times where a single network device may serve as both a DM
for other DAs in the network and, itself, as a device managed by
someone else. This may be the case on nodes serving as gateways or
proxies. The DTNMA accommodates this case by allowing a single
device to run both a DA and DM.
An example of this configuration is illustrated in Figure 7.
Data Fusion Control Flow
Birrane, et al. Expires 25 April 2024 [Page 48]
Internet-Draft DTNMA October 2023
---------------------------------------
| Node B |
| |
+-----------+ | +-----------+ +---------+ | +---------+
| DTNMA | | | DTNMA | | DTNMA | | | DTNMA |
| Manager A | | | Manager B | | Agent B | | | Agent C |
+---+-------+ | +-----+-----+ +----+----+ | +----+----+
| | | | | |
|---------------DEF(NULL,V0,EDD1+EDD2)->| | | (1)
|------------------PROD(EDD1&EDD2,V0)-->| | |
| | | | | |
| | | | | |
| | |--------------------PROD(1s, EDD2)->| (2)
| | | | | |
| | | | | |
| | |<--------------------RPT(EDD2)------| (3)
| | | | | |
|<------------------RPT(V0)-------------| | | (4)
| | | | | |
| | | | | |
| |
| |
---------------------------------------
Figure 7
A device can operate as both a DTNMA Manager and an Agent.
In this example, we presume that DA B is able to sample a given EDD
(EDD1) and that DA C is able to sample a different EDD (EDD2). Node
B houses DM B (which controls DA C) and DA B (which is controlled by
DM A). DM A must periodically receive some new value that is
calculated as a function of both EDD1 and EDD2.
First, DM A sends a policy to DA B to define a variable (V0) whose
value is given by the mathematical expression (EDD1 + EDD2) without a
restricting ACL. Further, DM A sends a policy to DA B to report on
the value of V0 every second (step 1).
DA B can require the ability to monitor both EDD1 and EDD2. However,
the only way to receive EDD2 values is to have them reported back to
Node B by DA C and included in the Node B runtime data stores.
Therefore, DM B sends a policy to DA C to report on the value of EDD2
(step 2).
DA C receives the policy in its autonomy engine and produces reports
on the value of EDD2 every second (step 3).
Birrane, et al. Expires 25 April 2024 [Page 49]
Internet-Draft DTNMA October 2023
DA B may locally sample EDD1 and EDD2 and uses that to compute values
of V0 and report on those values at regular intervals to DM A (step
4).
While a trivial example, the mechanism of associating fusion with the
Agent function rather than the Manager function scales with fusion
complexity. Within the DTNMA, DAs and DMs are not required to be
separate software implementations. There may be a single software
application running on Node B implementing both DM B and DA B roles.
11. IANA Considerations
This informational document requires no registrations to be managed
by IANA.
12. Security Considerations
Security within a DTNMA MUST exist in at least two layers: security
in the data model and security in the messaging and encoding of the
data model.
Data model security refers to the confidentiality of elements of a
data model and the authorization of DTNMA actors to access those
elements. For example, elements of a data model might be available
to certain DAs or DMs in a system, whereas the same elements may be
hidden from other DAs or DMs.
| NOTE: One way to provide finer-grained application security is
| through the use of Access Control Lists (ACLs) that would be
| defined as part of the configuration of DAs and DMs. It is
| expected that many common data model tools provide mechanisms
| for the definition of ACLs and best practices for their
| operational use.
The exchange of information between and amongst DAs and DMs in the
DTNMA is expected to be accomplished through some messaging
transport. As such, security at the transport layer is expected to
address the questions of authentication, integrity, and
confidentiality.
13. Acknowledgements
Brian Sipos of the Johns Hopkins University Applied Physics
Laboratory (JHU/APL) provided excellent technical review of the DTNMA
concepts presented in this document.
14. Informative References
Birrane, et al. Expires 25 April 2024 [Page 50]
Internet-Draft DTNMA October 2023
[I-D.ietf-core-comi]
Veillette, M., Van der Stok, P., Pelov, A., Bierman, A.,
and C. Bormann, "CoAP Management Interface (CORECONF)",
Work in Progress, Internet-Draft, draft-ietf-core-comi-16,
4 September 2023, <https://datatracker.ietf.org/doc/html/
draft-ietf-core-comi-16>.
[I-D.ietf-core-sid]
Veillette, M., Pelov, A., Petrov, I., Bormann, C., and M.
Richardson, "YANG Schema Item iDentifier (YANG SID)", Work
in Progress, Internet-Draft, draft-ietf-core-sid-21, 29
August 2023, <https://datatracker.ietf.org/doc/html/draft-
ietf-core-sid-21>.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/info/rfc2119>.
[RFC2578] McCloghrie, K., Ed., Perkins, D., Ed., and J.
Schoenwaelder, Ed., "Structure of Management Information
Version 2 (SMIv2)", STD 58, RFC 2578,
DOI 10.17487/RFC2578, April 1999,
<https://www.rfc-editor.org/info/rfc2578>.
[RFC2982] Kavasseri, R., Ed., "Distributed Management Expression
MIB", RFC 2982, DOI 10.17487/RFC2982, October 2000,
<https://www.rfc-editor.org/info/rfc2982>.
[RFC3165] Levi, D. and J. Schoenwaelder, "Definitions of Managed
Objects for the Delegation of Management Scripts",
RFC 3165, DOI 10.17487/RFC3165, August 2001,
<https://www.rfc-editor.org/info/rfc3165>.
[RFC3410] Case, J., Mundy, R., Partain, D., and B. Stewart,
"Introduction and Applicability Statements for Internet-
Standard Management Framework", RFC 3410,
DOI 10.17487/RFC3410, December 2002,
<https://www.rfc-editor.org/info/rfc3410>.
[RFC3411] Harrington, D., Presuhn, R., and B. Wijnen, "An
Architecture for Describing Simple Network Management
Protocol (SNMP) Management Frameworks", STD 62, RFC 3411,
DOI 10.17487/RFC3411, December 2002,
<https://www.rfc-editor.org/info/rfc3411>.
Birrane, et al. Expires 25 April 2024 [Page 51]
Internet-Draft DTNMA October 2023
[RFC3416] Presuhn, R., Ed., "Version 2 of the Protocol Operations
for the Simple Network Management Protocol (SNMP)",
STD 62, RFC 3416, DOI 10.17487/RFC3416, December 2002,
<https://www.rfc-editor.org/info/rfc3416>.
[RFC3418] Presuhn, R., Ed., "Management Information Base (MIB) for
the Simple Network Management Protocol (SNMP)", STD 62,
RFC 3418, DOI 10.17487/RFC3418, December 2002,
<https://www.rfc-editor.org/info/rfc3418>.
[RFC4838] Cerf, V., Burleigh, S., Hooke, A., Torgerson, L., Durst,
R., Scott, K., Fall, K., and H. Weiss, "Delay-Tolerant
Networking Architecture", RFC 4838, DOI 10.17487/RFC4838,
April 2007, <https://www.rfc-editor.org/info/rfc4838>.
[RFC4949] Shirey, R., "Internet Security Glossary, Version 2",
FYI 36, RFC 4949, DOI 10.17487/RFC4949, August 2007,
<https://www.rfc-editor.org/info/rfc4949>.
[RFC6241] Enns, R., Ed., Bjorklund, M., Ed., Schoenwaelder, J., Ed.,
and A. Bierman, Ed., "Network Configuration Protocol
(NETCONF)", RFC 6241, DOI 10.17487/RFC6241, June 2011,
<https://www.rfc-editor.org/info/rfc6241>.
[RFC6991] Schoenwaelder, J., Ed., "Common YANG Data Types",
RFC 6991, DOI 10.17487/RFC6991, July 2013,
<https://www.rfc-editor.org/info/rfc6991>.
[RFC7228] Bormann, C., Ersue, M., and A. Keranen, "Terminology for
Constrained-Node Networks", RFC 7228,
DOI 10.17487/RFC7228, May 2014,
<https://www.rfc-editor.org/info/rfc7228>.
[RFC7252] Shelby, Z., Hartke, K., and C. Bormann, "The Constrained
Application Protocol (CoAP)", RFC 7252,
DOI 10.17487/RFC7252, June 2014,
<https://www.rfc-editor.org/info/rfc7252>.
[RFC7575] Behringer, M., Pritikin, M., Bjarnason, S., Clemm, A.,
Carpenter, B., Jiang, S., and L. Ciavaglia, "Autonomic
Networking: Definitions and Design Goals", RFC 7575,
DOI 10.17487/RFC7575, June 2015,
<https://www.rfc-editor.org/info/rfc7575>.
[RFC7950] Bjorklund, M., Ed., "The YANG 1.1 Data Modeling Language",
RFC 7950, DOI 10.17487/RFC7950, August 2016,
<https://www.rfc-editor.org/info/rfc7950>.
Birrane, et al. Expires 25 April 2024 [Page 52]
Internet-Draft DTNMA October 2023
[RFC8040] Bierman, A., Bjorklund, M., and K. Watsen, "RESTCONF
Protocol", RFC 8040, DOI 10.17487/RFC8040, January 2017,
<https://www.rfc-editor.org/info/rfc8040>.
[RFC8199] Bogdanovic, D., Claise, B., and C. Moberg, "YANG Module
Classification", RFC 8199, DOI 10.17487/RFC8199, July
2017, <https://www.rfc-editor.org/info/rfc8199>.
[RFC8342] Bjorklund, M., Schoenwaelder, J., Shafer, P., Watsen, K.,
and R. Wilton, "Network Management Datastore Architecture
(NMDA)", RFC 8342, DOI 10.17487/RFC8342, March 2018,
<https://www.rfc-editor.org/info/rfc8342>.
[RFC8368] Eckert, T., Ed. and M. Behringer, "Using an Autonomic
Control Plane for Stable Connectivity of Network
Operations, Administration, and Maintenance (OAM)",
RFC 8368, DOI 10.17487/RFC8368, May 2018,
<https://www.rfc-editor.org/info/rfc8368>.
[RFC8639] Voit, E., Clemm, A., Gonzalez Prieto, A., Nilsen-Nygaard,
E., and A. Tripathy, "Subscription to YANG Notifications",
RFC 8639, DOI 10.17487/RFC8639, September 2019,
<https://www.rfc-editor.org/info/rfc8639>.
[RFC8641] Clemm, A. and E. Voit, "Subscription to YANG Notifications
for Datastore Updates", RFC 8641, DOI 10.17487/RFC8641,
September 2019, <https://www.rfc-editor.org/info/rfc8641>.
[RFC8990] Bormann, C., Carpenter, B., Ed., and B. Liu, Ed., "GeneRic
Autonomic Signaling Protocol (GRASP)", RFC 8990,
DOI 10.17487/RFC8990, May 2021,
<https://www.rfc-editor.org/info/rfc8990>.
[RFC8993] Behringer, M., Ed., Carpenter, B., Eckert, T., Ciavaglia,
L., and J. Nobre, "A Reference Model for Autonomic
Networking", RFC 8993, DOI 10.17487/RFC8993, May 2021,
<https://www.rfc-editor.org/info/rfc8993>.
[RFC9171] Burleigh, S., Fall, K., and E. Birrane, III, "Bundle
Protocol Version 7", RFC 9171, DOI 10.17487/RFC9171,
January 2022, <https://www.rfc-editor.org/info/rfc9171>.
[RFC9172] Birrane, III, E. and K. McKeever, "Bundle Protocol
Security (BPSec)", RFC 9172, DOI 10.17487/RFC9172, January
2022, <https://www.rfc-editor.org/info/rfc9172>.
Birrane, et al. Expires 25 April 2024 [Page 53]
Internet-Draft DTNMA October 2023
[xml-infoset]
World Wide Web Consortium, "XML Information Set (Second
Edition)", February 2004,
<https://www.w3.org/TR/2004/REC-xml-infoset-20040204/>.
[xpath] Clark, J.C. and R.D. DeRose, "XML Path Language (XPath)
Version 1.0", 1999.
Authors' Addresses
Edward J. Birrane
Johns Hopkins Applied Physics Laboratory
Email: Edward.Birrane@jhuapl.edu
Sarah E. Heiner
Johns Hopkins Applied Physics Laboratory
Email: Sarah.Heiner@jhuapl.edu
Emery Annis
Johns Hopkins Applied Physics Laboratory
Email: Emery.Annis@jhuapl.edu
Birrane, et al. Expires 25 April 2024 [Page 54]