Definitions of Managed Objects for the ADSL Lines
RFC 2662
Document | Type | RFC - Proposed Standard (August 1999) Errata | |
---|---|---|---|
Authors | Gregory Bathrick , Faye Ly | ||
Last updated | 2020-01-21 | ||
RFC stream | Internet Engineering Task Force (IETF) | ||
Formats | |||
Additional resources | Mailing list discussion | ||
IESG | Responsible AD | (None) | |
Send notices to | (None) |
RFC 2662
Network Working Group G. Bathrick Request for Comments: 2662 AG Communication Systems Category: Standards Track F. Ly Copper Mountain Networks August 1999 Definitions of Managed Objects for the ADSL Lines Status of this Memo This document specifies an Internet standards track protocol for the Internet community, and requests discussion and suggestions for improvements. Please refer to the current edition of the "Internet Official Protocol Standards" (STD 1) for the standardization state and status of this protocol. Distribution of this memo is unlimited. Copyright Notice Copyright (C) The Internet Society (1999). All Rights Reserved. Table of Contents 1. Abstract .............................................. 1 2. The SNMP Network Management Framework ................. 2 3. Object Definitions ..................................... 3 4. Relationship of the ADSL LINE MIB with standard MIBs ... 3 5. Conventions used in the MIB ............................ 7 6. Conformance and Compliance ............................. 17 7. Definitions ............................................ 17 8. Acknowledgments ........................................ 110 9. References ............................................. 111 10. Security Considerations ................................ 113 11. Intellectual Property Notice ........................... 114 12. Authors' Addresses ..................................... 114 13. Full Copyright Statement ............................... 115 1. Abstract This document defines a standard SNMP MIB for ADSL lines based on the ADSL Forum standard data model [9]. The ADSL standard describes ATU-C and ATU-R as two sides of the ADSL line. This MIB covers both ATU-C and ATU-R agent's perspectives. Each instance defined in the MIB represents a single ADSL line. Bathrick & Ly Standards Track [Page 1] RFC 2662 ADSL Line MIB August 1999 It should be noted that the ADSL Forum Network Management Working Group provided input towards the content of this document. See the Acknowledgement Section for a list of individuals who made this document possible. 2. The SNMP Network Management Framework The SNMP Management Framework presently consists of five major components: o An overall architecture, described in RFC 2571 [13]. o Mechanisms for describing and naming objects and events for the purpose of management. The first version of this Structure of Management Information (SMI) is called SMIv1 and described in STD 16, RFC 1155 [14], STD 16, RFC 1212 [15] and RFC 1215 [16]. The second version, called SMIv2, is described in STD 58, RFC 2578 [1], STD 58, RFC 2579 [2] and STD 58, RFC 2580 [17]. o Message protocols for transferring management information. The first version of the SNMP message protocol is called SNMPv1 and described in STD 15, RFC 1157 [7]. A second version of the SNMP message protocol, which is not an Internet standards track protocol, is called SNMPv2c and described in RFC 1901 [18] and RFC 1906 [19]. The third version of the message protocol is called SNMPv3 and described in RFC 1906 [19], RFC 2572 [20] and RFC 2574 [21]. o Protocol operations for accessing management information. The first set of protocol operations and associated PDU formats is described in STD 15, RFC 1157 [7]. A second set of protocol operations and associated PDU formats is described in RFC 1905 [8]. o A set of fundamental applications described in RFC 2573 [22] and the view-based access control mechanism described in RFC 2575 [23]. This document specifies a MIB module that is compliant to the SMIv2. A MIB conforming to the SMIv1 can be produced through the appropriate translations. The resulting translated MIB must be semantically equivalent, except where objects or events are omitted because no translation is possible (e.g., use of Counter64). Some machine readable information in SMIv2 will be converted into textual descriptions in SMIv1 during the translation process. However, this loss of machine readable information is not considered to change the semantics of the MIB. Bathrick & Ly Standards Track [Page 2] RFC 2662 ADSL Line MIB August 1999 3. Object Definitions Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. Objects in the MIB are defined using the extended subset of Abstract Syntax Notation One (ASN.1) defined in the SMI. In particular, each object type is named by an OBJECT IDENTIFIER, an administratively assigned name. The object type together with an object instance serves to uniquely identify a specific instantiation of the object. For human convenience, we often use a textual string, termed the descriptor, to also refer to the object type. 4. Relationship of the ADSL LINE MIB with standard MIBs This section outlines the relationship of ADSL Line MIB with other MIBs described in RFCs and in their various degrees of "standardization". 4.1 Use of the IfTable The ADSL LINE MIB specifies the detailed attributes of a data interface. As such, it needs to integrate with IF-MIB [5]. The IANA has assigned the following ifType(s) relative to ADSL: IANAifType ::= TEXTUAL-CONVENTION . . . SYNTAX INTEGER { . . . adsl(94), -- Asymmetric Digital Subscriber Loop . . . adslInterleave(124), -- ADSL Interleaved Channel adslFast(125), -- ADSL Fast Channel . . . } Interfaces of each of these types are modeled by this document. Most MIB tables in this document represent information of one of these interface types and are indexed by ifIndex. Remaining are `profile' tables which may be accessed by the profileIndex. This is explained in more detail in section 5.4 Profiles. Bathrick & Ly Standards Track [Page 3] RFC 2662 ADSL Line MIB August 1999 4.1.1 ADSL Interface Types As shown below, three ADSL interface types are defined in this document, namely physical, interleaved channel, and fast channel. The physical interface represents characteristics of the physical media associated with both the ATUC and ATUR. The interleaved and fast channel interface represent the characteristics of the two types of ADSL channels. For each ADSL Line, a physical interface always exists. Depending on which ADSL operational configuration is present (as listed in Figure 5), the channel interfaces (fast or interleaved) may or may not exist. ______ ______ | |____________________| | | ATUC | | ATUR | | |____________________| | |______| |______| | <----- physical --------> | | <--- fast channel ------> | | <- interleaved channel -> | Figure 1: ADSL Model 4.1.2 Use of IF-MIB (Interface MIB RFC 2233) [5] The following attributes are part of the required ifGeneralInformationGroup object group specified in RFC 2233 [5], and are not duplicated in the ADSL MIB. Keep in mind that these objects apply to the agent's view of the line. Bathrick & Ly Standards Track [Page 4] RFC 2662 ADSL Line MIB August 1999 ifTable Object Use for ADSL ================================================================== ifIndex Interface index. ifDescr See interfaces MIB [5] ifType physical - adsl(94) fast - adslFast(125) interleaved - adslInterleave(124) ifSpeed Transmit rate from the perspective of the agent. physical - line rate fast - channel rate interleaved - channel rate ifPhysAddress This object should have an octet string with zero length. ifAdminStatus See interfaces MIB [5] ifOperStatus See interfaces MIB [5] Supplemented by adslAturCurrStatus and adslAturCurrStatus ifLastChange See interfaces MIB [5] ifName See interfaces MIB [5] ifLinkUpDownTrapEnable See interfaces MIB [5] Default set as follows: physical - enabled(1) fast - disabled(2) interleaved - disabled(2) ifHighSpeed Speed of line in Mega-bits per second (ifSpeed/1,000,000) ifConnectorPresent See interfaces MIB [5] Default set as follows: physical - true(1) fast - false(2) Bathrick & Ly Standards Track [Page 5] RFC 2662 ADSL Line MIB August 1999 interleaved - false(2) ifAlias See interfaces MIB [5] ifTableLastChange See interfaces MIB [5] ================================================================== Figure 2: Use of ifTable Objects: ifGeneralInformationGroup Use of the ifStackTable to associate the entries for physical, fast, interleaved channels, and higher layers (e.g., ATM) is shown below in figure 3. Use of ifStackTable is necessary, because configuration information is stored in profile tables associated with the physical-layer ifEntry only. The channels' ifEntrys need the ifStackTable to find their associated physical-layer entry and thus their configuration parameters. (See Profile section, 5.4). ______ (ifEntry=j) ______ | | fast channel | | | |________________________| | | | and/or | | | | | | | | (ifEntry=k) | | | | interleaved channel | | | |________________________| | | ATUC | | ATUR | | | | | | | (ifEntry=i) | | | | physical | | | |________________________| | |______| |______| Figure 3: Use of ifStackTable (part 1) The ifStackTable is then used to show the relationships between the various ADSL interfaces, as illustrated below in figure 4. HigherLayer LowerLayer -------------------------- j i k i Figure 4: Use of ifStackTable (part 2) The ifRcvAddressTable is not applicable for ADSL interfaces. Bathrick & Ly Standards Track [Page 6] RFC 2662 ADSL Line MIB August 1999 4.2 Relationship with RFC 2037 [25] Implementation of the Entity MIB [25] is optional. It in no way alters the information required in the adslLineMib, nor does it alter the relationship with IF-MIB. The Entity MIB introduces a standardized way of presenting the components of complex systems, such as a Digital Subscriber Line Access Multiplexer (DSLAM), that may contain multiple racks, shelves, line cards, and/or ports. The Entity MIB's main goal is to present these system components, their containment relationship, and mapping information with other MIBs such as the Interface MIB and the adslLineMib. If ATU-C agent is implemented, the Entity MIB should include entities for the ATU-C in the entPhysicalTable. The MIB's entAliasMappingTable would contain mapping information identifying the 'ifIndex' object associated with each ATU-C. However, if ATU-R agent is implemented, the Entity MIB should include entities for the ATU-R in the entPhysicalTable. In this case, the MIB's entAliasMappingTable would contain mapping information identifying the 'ifIndex' object associated with each ATU-R. Also associating the relationship between the ifTable and Entity MIB, the entPhysicalTable contains an 'entPhysicalName' object, which approximates the semantics of the 'ifName' object from the Interface MIB. 5. Conventions used in the MIB 5.1 Naming Conventions A. Atuc/Atur are used for the ATU-C and ATU-R. In other RFCs, these are sometimes referred to as the Near End (Ne) and Far End (Fe) respectively, but not in this document. B. The terms, "transmit" and "receive", are from the perspective of the corresponding table's end of the line. For example, in the case of Fast channels, adslAtucChanConfFastMaxTxRate defines the "downstream" rate, while adslAturChanConfFastMaxTxRate defines the "upstream" rate for a particular channel. C. There are two possible channels: fast, and interleaved. None, one or both may be implemented on a particular ADSL Line. Figure 5 illustrates all possible operational configurations. Bathrick & Ly Standards Track [Page 7] RFC 2662 ADSL Line MIB August 1999 D. Lof, Lol, Los, Lpr mean Loss of Framing, Link, Signal, and Power, respectively. Lpr is used by T1E1, so it is used for consistency (rather than Lop). A Loss of Link condition is declared at the ATU-C if a Loss of Signal is not preceded by a `dying-gasp' message from the ATU-R. Note that Loss of Link is only supported by the ATU-C. E. ES means errored second. An Errored Second is any second containing one or more CRC anomaly, or one or more Los(s) or Severely Errored Frame (Sef) defect(s). F. A "block" is a physical-layer `data buffer' over which CRCs are calculated. For example, in DMT, the block is defined as the ADSL superframe. The block duration is 250 micro-seconds so the block length in bytes, as defined in adslAtu*ChanCrcBlockLength, varies with data rate. See Line Code Specific MIBs [11] [12] for more line code specific information. G. Atn means Attenuation, Psd is Power Spectral Density and Snr is Signal to Noise Ratio. H. LCS means line code specific, e.g., o DMT = Discrete MultiTone o CAP = Carrierless Amplitude and Phase modulation and o QAM = Quadrature Amplitude Modulation I. Vendor (in the Inventory objects) refers to the manufacturer of the ATU-C or ATU-R assembly, not the modem chip vendor. When in doubt, use the manufacturer of the smallest field replaceable unit (e.g., stand-alone modem box, plug-in board). J. RADSL - Rate Adaptive Asymmetric Digital Subscriber Loop 5.2 Structure The MIB has multiple parallel tables. There are tables for: o line - common attributes o atuc and atur status Bathrick & Ly Standards Track [Page 8] RFC 2662 ADSL Line MIB August 1999 o atuc and atur performance - Current and up to 96 buckets of 15 min performance history - Current and Previous 1-day bucket performance history o profiles - configuration parameters and alarm parameters There are separate tables for Physical and Channel layers. Since their attributes are similar, only one set of "channel" tables are defined to be used for both fast and interleaved channels. The corresponding ifType gives the proper interpretation for that ifEntry. It is intented that Line Code Specific MIBs be located under adslLCSMib. These MIBs will be defined in separate modules. There could have been fewer tables by combining the ATU-C and ATU-R information into shared tables. However, the tables are more easily read when there are two identical sets of data. The figure below lists the five possible ADSL operational configurations. (indicated by the value of the adslLineType). In all configurations, the physical line interface entry will exist. However, the existence of the ADSL channel varies in each case, as shown below. Table Phys Fast Interleaved ___________________________________________________________ No Channels (1) | Y | | | Fast Only (2) | Y | Y | | Interleaved Only (3) | Y | | Y | Fast or Interleaved (4) | Y | Y | Y | Fast and Interleaved (5) | Y | Y | Y | Figure 5: ADSL Operational configurations NOTE: In (4), channel exists of either Fast or Interleaved type, but not both. The Manager may select the type of channel to be used. Depending on which operation configuration exists, some or all ADSL MIB tables could be supported, as shown in below. See Conformance Statements for more information on which objects are mandatory. Bathrick & Ly Standards Track [Page 9] RFC 2662 ADSL Line MIB August 1999 Table Phys Fast Interleaved ___________________________________________________________ adslLineTable | Y | | | adslAtucPhysTable | Y | | | adslAturPhysTable | Y | | | adslAtucChanTable | | Y | Y | adslAturChanTable | | Y | Y | adslAtucPerfDataTable | Y | | | adslAturPerfDataTable | Y | | | adslAtucIntervalTable | Y | | | adslAturIntervalTable | Y | | | adslAtucChanPerfDataTable | | Y | Y | adslAturChanPerfDataTable | | Y | Y | adslAtucChanIntervalTable | | Y | Y | adslAturChanIntervalTable | | Y | Y | Figure 6: Use of ADSL MIB Tables with various ifIndex values NOTE: The adslLineConfProfileTable and adslLineAlarmConfProfileTable will be present for all scenarios. See Profile Section of this document for implementation details such as profile creation, assignment, and indexing. 5.2.1 Structure of Conformance Groups The MIB is organized to cover both ends of the ADSL line, ATU-C and ATU-R. Objects defined can be categorized into two groups: the ATU-C group which provides objects that are supported by ATU-C agents and the ATU-R group which provides objects that are supported by ATU-R agents. These two groups are defined by the conformance section of the MIB. All objects defined in the MIB module are supported by the ATU-C agent and only portions of the objects are supported by the ATU-R agent. Figure 7 lists all tables/objects that are supported by the ATU-R agent. Bathrick & Ly Standards Track [Page 10] RFC 2662 ADSL Line MIB August 1999 Table Objects _______________________________________________________ adslLineTable adslLineCoding adslAtucPhysTable adslAtucInvVendorID adslAtucInvVersionNumber adslAtucCurrStatus (Partial) adslAtucCurrOutputPwr adslAtucCurrAttainableRate adslAturPhysTable all are supported adslAtucChanTable all except adslAtucChanCrcBlockLength are supported adslAtucPerfDataTable all except adslAtucPerfLols, adslAtucPerfLprs adslAtucPerfCurr15MinLols, adslAtucPerfCurr15MinLprs, adslAtucPerfCurr1DayLols, adslAtucPerfCurr1DayLprs, adslAtucPerfPrev1DayLols and adslAtucPerfPrev1DayLprs are supported adslAturPerfDataTable all are supported adslAtucIntervalTable adslAtucIntervalLofs adslAtucIntervalLoss adslAtucIntervalESs adslAtucIntervalInits adslAtucIntervalValidData adslAturIntervalTable all are supported adslAtucChanPerfDataTable all are supported adslAturChanPerfDataTable all are supported adslAtucChanIntervalTable all are supported adslAturChanIntervalTable all are supported adslLineConfProfileTable not supported adslLineAlarmConfProfileTable all are supported except adslAtucThresh15MinLols and adslAtucThresh15MinLprs -------------------------------------------------------------------- Figure 7: MIB Tables and Objects Supported by the ATU-R Agent Bathrick & Ly Standards Track [Page 11] RFC 2662 ADSL Line MIB August 1999 All traps supported by the ATU-R agent are also listed: adslAtucPerfLofsThreshTrap adslAtucPerfLossThreshTrap adslAtucPerfESsThreshTrap adslAtucRateChangeTrap adslAturPerfLofsThreshTrap adslAturPerfLossThreshTrap adslAturPerfLprsThreshTrap adslAturPerfESsThreshTrap adslAturRateChangeTrap 5.3 Counters, Interval Buckets and Thresholds For physical-level ES, Los, Lof, Lol, Lpr and line initialization attempts, there are event counters, current 15-minute and one (up to 96) 15-minute history bucket(s) of "interval-counters", as well as current and previous 1-day interval-counters. Each physical-layer current 15-minute event bucket has threshold trap. At the channel level, there are counters for total received blocks, received-and-corrected blocks, received-but-uncorrectable blocks, and transmitted blocks. There are the same set of 15-minute and 1-day buckets as at the physical-layer. There is no requirement for an agent to ensure fixed relationship between the start of a fifteen minute and any wall clock; however some implementations may align the fifteen minute intervals with quarter hours. Likewise, an implementation may choose to align one day intervals with start of a day. Separate tables are provided for the 96 interval-counters. They are indexed by {ifIndex, AdslAtu*IntervalNumber}. Counters are not reset when an ATU-C or ATU-R is reinitialized, only when the agent is reset or reinitialized (or under specific request outside the scope of this MIB). The 15-minute event counters are of type PerfCurrentCount and PerfIntervalCount. The 1-day event counters are of type AdslPerfCurrDayCount and AdslPerfPrevDayCount. Both 15-minute and 1- day time elapsed counters are of type AdslPerfTimeElapsed. Bathrick & Ly Standards Track [Page 12] RFC 2662 ADSL Line MIB August 1999 5.4 Profiles As a managed node can handle a large number of ATU-Cs (e.g., hundreds or perhaps thousands of ADSL lines), provisioning every parameter on every ATU-C may become burdensome. In response, two MIB tables have been created to define ADSL equipment configuration data profiles, as well as a mechanism to associate the equipment to these profiles. Profile tables may be implemented in one of two ways, but not simultaneously: o MODE-I: Dynamic Profiles - one profile shared by one or multiple ADSL lines. o MODE-II: Static Profiles - one profile per ADSL physical line always. 5.4.1 MODE-I : Dynamic Profiles Implementations using this mode will enable the manager to dynamically create and delete profiles as needed. The index of the profile is an locally-unique administratively assigned name for the profile having the textual convention `SnmpAdminString' (RFC2571 [13]). One or more ADSL lines may be configured to share parameters of a single profile (e.g., adslLineConfProfileName = `silver') by setting its adslLineConfProfile objects to the index value of this profile. If a change is made to the profile, all lines that refer to it will be re-configured to the changed parameters. Before a profile can be deleted or taken out of service it must be first unreferenced from all associated lines. This figure below shows an example of how this mode can be implemented. In the example, ADSL lines `1' and `x' share the configuration of the `silver' profile, while line `2' uses the `platinum' profile. The `gold' profile has no lines associated with it. Bathrick & Ly Standards Track [Page 13] RFC 2662 ADSL Line MIB August 1999 ADSL ifIndex ifTable Configuration Line Profile Table __________________________________________________________________ 1 i1 ADSL Line -- ---> Platinum Profile j1 Fast Chan | | k1 Int Chan | | | ^ v | Gold Profile 2 i2 ADSL Line ------->---- j2 Fast Chan | k2 Int Chan | | | | v x ix ADSL Line ------>------> Silver Profile jx Fast Chan ---------------> kx Int Chan __________________________________________________________________ Figure 8: Use of Dynamic Profiles: MODE-I In the figure above, note that three interface entries of an ADSL line, physical, fast channel, and interleaved channel, are represented by `i', `j', and `k'. Only the physical-layer entry `i' contains an adslLineTable entry, therefore only those entries contain pointers to the adslLineConfProfileTable. The ifStackTable (see rfc2233 [5]) can be used to link the channel entries to the corresponding physical-layer entry to get the channel's configuration parameters. See figure 4 for use of the ifStackTable. The same characteristics and mechanisms are present for the alarm profile type. There is no requirement that its index be the same as the configuration profile. Implementations of this mode, must provide a default profile whose name is `DEFVAL' for each profile type: Configuration and Alarm. The values of the associated parameters will be vendor specific unless otherwise indicated in this document. Before a line's profiles have been set, these profiles will be automatically used by setting adslLineConfProfile and adslLineAlarmConfProfile to `DEFVAL'. Bathrick & Ly Standards Track [Page 14] RFC 2662 ADSL Line MIB August 1999 In this mode, profiles are created, assigned, and deleted dynamically using these four objects: adslLineConfProfile, adslLineConfProfileRowStatus, adslLineAlarmConfProfile, and adslLineAlarmConfProfileRowStatus. 5.4.2 MODE-II : Static Profiles Implementations with this mode will automatically create a profile one-for-one with each ADSL line physical entry. The name of this profile is a system generated read-only object whose value is equivalent to the index of the physical line. The Agent will not allow a Manager to create/delete profiles in this mode. Therefore, adslLineConfProfile, adslLineConfProfileRowStatus, adslLineAlarmConfProfile, and adslLineAlarmConfProfileRowStatus objects have minimal value in this mode and are read-only. The figure below shows an example of this mode. In the example, ADSL lines `1', `2', and `x' each have their own profiles. ADSL ifIndex ifTable Configuration Line Profile Table __________________________________________________________________ 1 i1 ADSL Line ------------> Profile j1 Fast Chan k1 Int Chan 2 i2 ADSL Line ------------> Profile j2 Fast Chan k2 Int Chan x ix ADSL Line ------------> Profile jx Fast Chan kx Int Chan __________________________________________________________________ Figure 9: Use of Static Profiles: MODE II 5.5 Traps These SNMP traps are required: coldStart / warmStart (per [6]) -- which are per agent (e.g., per DSLAM in such a device), and linkUp / linkDown (per [5]) -- which are per interface (i.e., ADSL line). Note: RFC 2233 [5] recommends that linkUp / linkDown only be used at a physical-layer ifEntry, as discussed above. Bathrick & Ly Standards Track [Page 15] RFC 2662 ADSL Line MIB August 1999 A linkDown trap is generated whenever any of Lof, Los, Lol, Loss of Signal Quality, or Lpr events occurs. At this operational point, a manager can use adslAtu*CurrStatus for additional detailed information. The corresponding linkUp trap is sent when all link failure conditions are cleared. The traps defined in this MIB are for initialization failure, rate change, and for the threshold crossings associated with the following events: Lofs, Lols, Loss, Lprs, and ESs. Each threshold has its own enable/threshold value. When that value is 0, the trap is disabled. The current status objects (adslAtu*CurrStatus) indicate, through a bitmask, all outstanding error conditions or that the line is operational. Note that each object claims to represent the status of the modem at that end of the line. However, since the SNMP agent likely co-resides with only one end of the line, the corresponding far-end current status object may be incomplete. For example, when there are errors on the line, the far-end ATU may not be able to correctly report this condition. Therefore, not all conditions are included in its current status. A threshold trap occurs whenever the corresponding current 15-minute interval error counter becomes equal and/or exceeds to the threshold value. One trap will be sent per interval per interface. Since the current 15-minute counter are reset to 0 every 15 minutes, if the condition persists, the trap may recur as often as every 15 minutes. For example, to get a trap whenever a "loss of" event occurs (but at most once every 15 minutes), set the corresponding "Thresh15Min" to 1. The agent will generate a trap when the event originally occurs. Note that the NMS will get a linkDown trap, as well, if enabled. At the beginning of the next 15 minute interval, the counter is reset. When the first second goes by and the event occurs, the current interval bucket will be 1, which equals the threshold and the trap will be sent again. The rate change trap is invoked when the transmit rate on a channel either increases by adsl(x)Thresh(y)RateUp or decreases by adsl(x)Thresh(y)RateDown. The trap is per direction:(x) == Atuc or Atur, and per channel: (y) == Fast or Interleave. In other words, the trap is sent whenever the rate changes in either direction on either channel and: CurrTxRate >= PrevTxRate plus ThreshRateUp or CurrTxRate <= PrevTxRate minus ThreshRateDown Bathrick & Ly Standards Track [Page 16] RFC 2662 ADSL Line MIB August 1999 No trap is sent on initialization. It can be disabled by setting the Up (and/or) Down threshold rates to 0. The PrevTxRate object is set to the current value at initialization and when a trap is sent. Thus rate changes are cumulative until the total change reaches the threshold. 6. Conformance and Compliance See the conformance and compliance statements within the information module. 7. Definitions ADSL-TC-MIB DEFINITIONS ::= BEGIN IMPORTS transmission, MODULE-IDENTITY, Gauge32 FROM SNMPv2-SMI TEXTUAL-CONVENTION FROM SNMPv2-TC; adsltcmib MODULE-IDENTITY LAST-UPDATED "9908190000Z" ORGANIZATION "IETF ADSL MIB Working Group" CONTACT-INFO " Gregory Bathrick AG Communication Systems A Subsidiary of Lucent Technologies 2500 W Utopia Rd. Phoenix, AZ 85027 USA Tel: +1 602-582-7679 Fax: +1 602-582-7697 E-mail: bathricg@agcs.com Faye Ly Copper Mountain Networks Norcal Office 2470 Embarcadero Way Palo Alto, CA 94303 Tel: +1 650-858-8500 Fax: +1 650-858-8085 E-Mail: faye@coppermountain.com Bathrick & Ly Standards Track [Page 17] RFC 2662 ADSL Line MIB August 1999 IETF ADSL MIB Working Group (adsl@xlist.agcs.com) " DESCRIPTION "The MIB module which provides a ADSL Line Coding Textual Convention to be used by ADSL Lines." -- Revision history REVISION "9908190000Z" -- 19 August 1999, midnight DESCRIPTION "Initial Version, published as RFC 2662" ::= { transmission 94 2 } -- adslMIB 2 AdslLineCodingType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This data type is used as the syntax for the ADSL Line Code." SYNTAX INTEGER { other(1),-- none of the following dmt (2), -- Discrete MultiTone cap (3), -- Carrierless Amplitude & Phase modulation qam (4) -- Quadrature Amplitude Modulation } AdslPerfCurrDayCount ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "A counter associated with interface performance measurements in a current 1-day (24 hour) measurement interval. The value of this counter starts at zero at the beginning of an interval and is increased when associated events occur, until the end of the 1-day interval. At that time the value of the counter is stored in the previous 1-day history interval, if available, and the current interval counter is restarted at zero. In the case where the agent has no valid data available for this interval the corresponding object instance is not available and upon a retrieval request a corresponding error message shall be returned to indicate that this instance does not exist (for example, a noSuchName error for SNMPv1 and a noSuchInstance for SNMPv2 GET operation)." Bathrick & Ly Standards Track [Page 18] RFC 2662 ADSL Line MIB August 1999 SYNTAX Gauge32 AdslPerfPrevDayCount ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "A counter associated with interface performance measurements during the most previous 1-day (24 hour) measurement interval. The value of this counter is equal to the value of the current day counter at the end of its most recent interval. In the case where the agent has no valid data available for this interval the corresponding object instance is not available and upon a retrieval request a corresponding error message shall be returned to indicate that this instance does not exist (for example, a noSuchName error for SNMPv1 and a noSuchInstance for SNMPv2 GET operation)." SYNTAX Gauge32 AdslPerfTimeElapsed ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The number of seconds that have elapsed since the beginning of the current measurement period. If, for some reason, such as an adjustment in the system's time-of-day clock, the current interval exceeds the maximum value, the agent will return the maximum value." SYNTAX Gauge32 END ADSL-LINE-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Counter32, Gauge32, NOTIFICATION-TYPE, transmission, Unsigned32 FROM SNMPv2-SMI RowStatus, TruthValue, VariablePointer FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF ifIndex FROM IF-MIB PerfCurrentCount, PerfIntervalCount FROM PerfHist-TC-MIB Bathrick & Ly Standards Track [Page 19] RFC 2662 ADSL Line MIB August 1999 SnmpAdminString FROM SNMP-FRAMEWORK-MIB AdslPerfCurrDayCount, AdslPerfPrevDayCount, AdslPerfTimeElapsed, AdslLineCodingType FROM ADSL-TC-MIB ; adslMIB MODULE-IDENTITY LAST-UPDATED "9908190000Z" ORGANIZATION "IETF ADSL MIB Working Group" CONTACT-INFO " Gregory Bathrick AG Communication Systems A Subsidiary of Lucent Technologies 2500 W Utopia Rd. Phoenix, AZ 85027 USA Tel: +1 602-582-7679 Fax: +1 602-582-7697 E-mail: bathricg@agcs.com Faye Ly Copper Mountain Networks Norcal Office 2470 Embarcadero Way Palo Alto, CA 94303 Tel: +1 650-858-8500 Fax: +1 650-858-8085 E-Mail: faye@coppermountain.com (ADSL Forum input only) John Burgess Predictive Systems, Inc. 25A Vreeland Rd. Florham Park, NJ 07932 USA Tel: +1 973-301-5610 Fax: +1 973-301-5699 E-mail: jtburgess@predictive.com IETF ADSL MIB Working Group (adsl@xlist.agcs.com) " DESCRIPTION "The MIB module defining objects for the management of a pair of ADSL modems at each end of the ADSL line. Each such line has Bathrick & Ly Standards Track [Page 20] RFC 2662 ADSL Line MIB August 1999 an entry in an ifTable which may include multiple modem lines. An agent may reside at either end of the ADSL line however the MIB is designed to require no management communication between them beyond that inherent in the low-level ADSL line protocol. The agent may monitor and control this protocol for its needs. ADSL lines may support optional Fast or Interleaved channels. If these are supported, additional entries corresponding to the supported channels must be created in the ifTable. Thus an ADSL line that supports both channels will have three entries in the ifTable, one for each physical, fast, and interleaved, whose ifType values are equal to adsl(94), fast(125), and interleaved(124), respectively. The ifStackTable is used to represent the relationship between the entries. Naming Conventions: Atuc -- (ATUC) modem at near (Central) end of line Atur -- (ATUR) modem at Remote end of line Curr -- Current Prev -- Previous Atn -- Attenuation ES -- Errored Second. LCS -- Line Code Specific Lof -- Loss of Frame Lol -- Loss of Link Los -- Loss of Signal Lpr -- Loss of Power xxxs-- interval of Seconds in which xxx occurs (e.g., xxx=Lof, Los, Lpr) Max -- Maximum Mgn -- Margin Min -- Minimum Psd -- Power Spectral Density Snr -- Signal to Noise Ratio Tx -- Transmit Blks-- Blocks, a data unit, see adslAtuXChanCrcBlockLength " -- Revision history REVISION "9908190000Z" -- 19 August 1999, midnight DESCRIPTION "Initial Version, published as RFC 2662" ::= { transmission 94 } adslLineMib OBJECT IDENTIFIER ::= { adslMIB 1 } adslMibObjects OBJECT IDENTIFIER ::= { adslLineMib 1 } Bathrick & Ly Standards Track [Page 21] RFC 2662 ADSL Line MIB August 1999 -- objects adslLineTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslLineEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes common attributes describing both ends of the line. It is required for all ADSL physical interfaces. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94)." ::= { adslMibObjects 1 } adslLineEntry OBJECT-TYPE SYNTAX AdslLineEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in adslLineTable." INDEX { ifIndex } ::= { adslLineTable 1 } AdslLineEntry ::= SEQUENCE { adslLineCoding AdslLineCodingType, adslLineType INTEGER, adslLineSpecific VariablePointer, adslLineConfProfile SnmpAdminString, adslLineAlarmConfProfile SnmpAdminString } adslLineCoding OBJECT-TYPE SYNTAX AdslLineCodingType MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the ADSL coding type used on this line." ::= { adslLineEntry 1 } adslLineType OBJECT-TYPE SYNTAX INTEGER { noChannel (1), -- no channels exist fastOnly (2), -- fast channel exists only interleavedOnly (3), -- interleaved channel exists -- only fastOrInterleaved (4),-- either fast or interleaved -- channels can exist, but -- only one at any time fastAndInterleaved (5)-- both fast or interleaved Bathrick & Ly Standards Track [Page 22] RFC 2662 ADSL Line MIB August 1999 -- channels exist } MAX-ACCESS read-only STATUS current DESCRIPTION "Defines the type of ADSL physical line entity that exists, by defining whether and how the line is channelized. If the line is channelized, the value will be other than noChannel(1). This object defines which channel type(s) are supported. In the case that the line is channelized, the manager can use the ifStackTable to determine the ifIndex for the associated channel(s)." ::= { adslLineEntry 2 } adslLineSpecific OBJECT-TYPE SYNTAX VariablePointer MAX-ACCESS read-only STATUS current DESCRIPTION "OID instance in vendor-specific MIB. The Instance may be used to determine shelf/slot/port of the ATUC interface in a DSLAM." ::= { adslLineEntry 3 } adslLineConfProfile OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "The value of this object identifies the row in the ADSL Line Configuration Profile Table, (adslLineConfProfileTable), which applies for this ADSL line, and channels if applicable. For `dynamic' mode, in the case which the configuration profile has not been set, the value will be set to `DEFVAL'. If the implementator of this MIB has chosen not to implement `dynamic assignment' of profiles, this object's MIN-ACCESS is read-only." ::= { adslLineEntry 4 } adslLineAlarmConfProfile OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..32)) MAX-ACCESS read-write Bathrick & Ly Standards Track [Page 23] RFC 2662 ADSL Line MIB August 1999 STATUS current DESCRIPTION "The value of this object identifies the row in the ADSL Line Alarm Configuration Profile Table, (adslLineAlarmConfProfileTable), which applies to this ADSL line, and channels if applicable. For `dynamic' mode, in the case which the alarm profile has not been set, the value will be set to `DEFVAL'. If the implementator of this MIB has chosen not to implement `dynamic assignment' of profiles, this object's MIN-ACCESS is read-only." ::= { adslLineEntry 5 } adslAtucPhysTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAtucPhysEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUC. Each row contains the Physical Layer Parameters table for that ATUC. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94)." ::= { adslMibObjects 2 } adslAtucPhysEntry OBJECT-TYPE SYNTAX AdslAtucPhysEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the adslAtucPhysTable." INDEX { ifIndex } ::= { adslAtucPhysTable 1 } AdslAtucPhysEntry ::= SEQUENCE { adslAtucInvSerialNumber SnmpAdminString, adslAtucInvVendorID SnmpAdminString, adslAtucInvVersionNumber SnmpAdminString, adslAtucCurrSnrMgn INTEGER, adslAtucCurrAtn Gauge32, adslAtucCurrStatus BITS, adslAtucCurrOutputPwr INTEGER, adslAtucCurrAttainableRate Gauge32 } -- inventory group Bathrick & Ly Standards Track [Page 24] RFC 2662 ADSL Line MIB August 1999 -- -- These items should describe the lowest level identifiable -- component, be it a stand-alone modem, a card in a rack, -- a child-board, etc. -- adslAtucInvSerialNumber OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The vendor specific string that identifies the vendor equipment." ::= { adslAtucPhysEntry 1 } adslAtucInvVendorID OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The vendor ID code is a copy of the binary vendor identification field defined by the PHY[10] and expressed as readable characters." REFERENCE "ANSI T1.413[10]" ::= { adslAtucPhysEntry 2 } adslAtucInvVersionNumber OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The vendor specific version number sent by this ATU as part of the initialization messages. It is a copy of the binary version number field defined by the PHY[10] and expressed as readable characters." REFERENCE "ANSI T1.413[10]" ::= { adslAtucPhysEntry 3 } -- current status group -- adslAtucCurrSnrMgn OBJECT-TYPE SYNTAX INTEGER (-640..640) UNITS "tenth dB" MAX-ACCESS read-only STATUS current DESCRIPTION "Noise Margin as seen by this ATU with respect to its received signal in tenth dB." Bathrick & Ly Standards Track [Page 25] RFC 2662 ADSL Line MIB August 1999 ::= { adslAtucPhysEntry 4 } adslAtucCurrAtn OBJECT-TYPE SYNTAX Gauge32(0..630) UNITS "tenth dB" MAX-ACCESS read-only STATUS current DESCRIPTION "Measured difference in the total power transmitted by the peer ATU and the total power received by this ATU." ::= { adslAtucPhysEntry 5 } adslAtucCurrStatus OBJECT-TYPE SYNTAX BITS { noDefect(0), lossOfFraming(1), lossOfSignal(2), lossOfPower(3), lossOfSignalQuality(4), lossOfLink(5), dataInitFailure(6), configInitFailure(7), protocolInitFailure(8), noPeerAtuPresent(9) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates current state of the ATUC line. This is a bit-map of possible conditions. The various bit positions are: 0 noDefect There no defects on the line 1 lossOfFraming ATUC failure due to not receiving valid frame. 2 lossOfSignal ATUC failure due to not receiving signal. 3 lossOfPower ATUC failure due to loss of power. Note: the Agent may still function. 4 lossOfSignalQuality Loss of Signal Quality is declared when the Noise Margin falls below the Minimum Noise Bathrick & Ly Standards Track [Page 26] RFC 2662 ADSL Line MIB August 1999 Margin, or the bit-error-rate exceeds 10^-7. 5 lossOfLink ATUC failure due to inability to link with ATUR. 6 dataInitFailure ATUC failure during initialization due to bit errors corrupting startup exchange data. 7 configInitFailure ATUC failure during initialization due to peer ATU not able to support requested configuration 8 protocolInitFailure ATUC failure during initialization due to incompatible protocol used by the peer ATU. 9 noPeerAtuPresent ATUC failure during initialization due to no activation sequence detected from peer ATU. This is intended to supplement ifOperStatus." ::= { adslAtucPhysEntry 6 } adslAtucCurrOutputPwr OBJECT-TYPE SYNTAX INTEGER (-310..310) UNITS "tenth dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "Measured total output power transmitted by this ATU. This is the measurement that was reported during the last activation sequence." ::= { adslAtucPhysEntry 7 } adslAtucCurrAttainableRate OBJECT-TYPE SYNTAX Gauge32 UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the maximum currently attainable data rate by the ATU. This value will be equal or greater than Bathrick & Ly Standards Track [Page 27] RFC 2662 ADSL Line MIB August 1999 the current line rate." ::= { adslAtucPhysEntry 8 } adslAturPhysTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAturPhysEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUR Each row contains the Physical Layer Parameters table for that ATUR. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94)." ::= { adslMibObjects 3 } adslAturPhysEntry OBJECT-TYPE SYNTAX AdslAturPhysEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the adslAturPhysTable." INDEX { ifIndex } ::= { adslAturPhysTable 1 } AdslAturPhysEntry ::= SEQUENCE { adslAturInvSerialNumber SnmpAdminString, adslAturInvVendorID SnmpAdminString, adslAturInvVersionNumber SnmpAdminString, adslAturCurrSnrMgn INTEGER, adslAturCurrAtn Gauge32, adslAturCurrStatus BITS, adslAturCurrOutputPwr INTEGER, adslAturCurrAttainableRate Gauge32 } -- inventory group -- adslAturInvSerialNumber OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The vendor specific string that identifies the vendor equipment." ::= { adslAturPhysEntry 1 } adslAturInvVendorID OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..16)) MAX-ACCESS read-only Bathrick & Ly Standards Track [Page 28] RFC 2662 ADSL Line MIB August 1999 STATUS current DESCRIPTION "The vendor ID code is a copy of the binary vendor identification field defined by the PHY[10] and expressed as readable characters." REFERENCE "ANSI T1.413" ::= { adslAturPhysEntry 2 } adslAturInvVersionNumber OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The vendor specific version number sent by this ATU as part of the initialization messages. It is a copy of the binary version number field defined by the PHY[10] and expressed as readable characters." REFERENCE "ANSI T1.413" ::= { adslAturPhysEntry 3 } -- current status group -- adslAturCurrSnrMgn OBJECT-TYPE SYNTAX INTEGER (-640..640) UNITS "tenth dB" MAX-ACCESS read-only STATUS current DESCRIPTION "Noise Margin as seen by this ATU with respect to its received signal in tenth dB." ::= { adslAturPhysEntry 4 } adslAturCurrAtn OBJECT-TYPE SYNTAX Gauge32(0..630) UNITS "tenth dB" MAX-ACCESS read-only STATUS current DESCRIPTION "Measured difference in the total power transmitted by the peer ATU and the total power received by this ATU." ::= { adslAturPhysEntry 5 } adslAturCurrStatus OBJECT-TYPE SYNTAX BITS { noDefect(0), lossOfFraming(1), lossOfSignal(2), lossOfPower(3), Bathrick & Ly Standards Track [Page 29] RFC 2662 ADSL Line MIB August 1999 lossOfSignalQuality(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates current state of the ATUR line. This is a bit-map of possible conditions. Due to the isolation of the ATUR when line problems occur, many state conditions like loss of power, loss of quality signal, and initialization errors, can not be determined. While trouble shooting ATUR, also use object, adslAtucCurrStatus. The various bit positions are: 0 noDefect There no defects on the line 1 lossOfFraming ATUR failure due to not receiving valid frame 2 lossOfSignal ATUR failure due to not receiving signal 3 lossOfPower ATUR failure due to loss of power 4 lossOfSignalQuality Loss of Signal Quality is declared when the Noise Margin falls below the Minimum Noise Margin, or the bit-error-rate exceeds 10^-7. This is intended to supplement ifOperStatus." ::= { adslAturPhysEntry 6 } adslAturCurrOutputPwr OBJECT-TYPE SYNTAX INTEGER (-310..310) UNITS "tenth dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "Measured total output power transmitted by this ATU. This is the measurement that was reported during the last activation sequence." ::= { adslAturPhysEntry 7 } adslAturCurrAttainableRate OBJECT-TYPE SYNTAX Gauge32 UNITS "bps" MAX-ACCESS read-only Bathrick & Ly Standards Track [Page 30] RFC 2662 ADSL Line MIB August 1999 STATUS current DESCRIPTION "Indicates the maximum currently attainable data rate by the ATU. This value will be equal or greater than the current line rate." ::= { adslAturPhysEntry 8 } adslAtucChanTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAtucChanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUC channel. ADSL channel interfaces are those ifEntries where ifType is equal to adslInterleave(124) or adslFast(125)." ::= { adslMibObjects 4 } adslAtucChanEntry OBJECT-TYPE SYNTAX AdslAtucChanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the adslAtucChanTable." INDEX { ifIndex } ::= { adslAtucChanTable 1 } AdslAtucChanEntry ::= SEQUENCE { adslAtucChanInterleaveDelay Gauge32, adslAtucChanCurrTxRate Gauge32, adslAtucChanPrevTxRate Gauge32, adslAtucChanCrcBlockLength Gauge32 } -- current group -- adslAtucChanInterleaveDelay OBJECT-TYPE SYNTAX Gauge32 UNITS "milli-seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement Bathrick & Ly Standards Track [Page 31] RFC 2662 ADSL Line MIB August 1999 in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency. In the case where the ifType is Fast(125), use noSuchObject." ::= { adslAtucChanEntry 1 } adslAtucChanCurrTxRate OBJECT-TYPE SYNTAX Gauge32 UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "Actual transmit rate on this channel." ::= { adslAtucChanEntry 2 } adslAtucChanPrevTxRate OBJECT-TYPE SYNTAX Gauge32 UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "The rate at the time of the last adslAtucRateChangeTrap event. It is also set at initialization to prevent a trap being sent. Rate changes less than adslAtucThresh(*)RateDown or less than adslAtucThresh(*)RateUp will not cause a trap or cause this object to change. (*) == Fast or Interleave. See AdslLineAlarmConfProfileEntry." ::= { adslAtucChanEntry 3 } adslAtucChanCrcBlockLength OBJECT-TYPE SYNTAX Gauge32 UNITS "byte" MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the length of the channel data-block on which the CRC operates. Refer to Line Code Specific MIBs, [11] and [12] for more information." ::= { adslAtucChanEntry 4 } Bathrick & Ly Standards Track [Page 32] RFC 2662 ADSL Line MIB August 1999 adslAturChanTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAturChanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUR channel. ADSL channel interfaces are those ifEntries where ifType is equal to adslInterleave(124) or adslFast(125)." ::= { adslMibObjects 5 } adslAturChanEntry OBJECT-TYPE SYNTAX AdslAturChanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the adslAturChanTable." INDEX { ifIndex } ::= { adslAturChanTable 1 } AdslAturChanEntry ::= SEQUENCE { adslAturChanInterleaveDelay Gauge32, adslAturChanCurrTxRate Gauge32, adslAturChanPrevTxRate Gauge32, adslAturChanCrcBlockLength Gauge32 } -- current group -- adslAturChanInterleaveDelay OBJECT-TYPE SYNTAX Gauge32 UNITS "milli-seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency. In the case where the ifType is Fast(125), use Bathrick & Ly Standards Track [Page 33] RFC 2662 ADSL Line MIB August 1999 noSuchObject." ::= { adslAturChanEntry 1 } adslAturChanCurrTxRate OBJECT-TYPE SYNTAX Gauge32 UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "Actual transmit rate on this channel." ::= { adslAturChanEntry 2 } adslAturChanPrevTxRate OBJECT-TYPE SYNTAX Gauge32 UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "The rate at the time of the last adslAturRateChangeTrap event. It is also set at initialization to prevent a trap being sent. Rate changes less than adslAturThresh(*)RateDown or less than adslAturThresh(*)RateUp will not cause a trap or cause this object to change. (*) == Fast or Interleave. See AdslLineAlarmConfProfileEntry." ::= { adslAturChanEntry 3 } adslAturChanCrcBlockLength OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the length of the channel data-block on which the CRC operates. Refer to Line Code Specific MIBs, [11] and [12] for more information." ::= { adslAturChanEntry 4 } adslAtucPerfDataTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAtucPerfDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUC. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94)." ::= { adslMibObjects 6 } Bathrick & Ly Standards Track [Page 34] RFC 2662 ADSL Line MIB August 1999 adslAtucPerfDataEntry OBJECT-TYPE SYNTAX AdslAtucPerfDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in adslAtucPerfDataTable." INDEX { ifIndex } ::= { adslAtucPerfDataTable 1 } AdslAtucPerfDataEntry ::= SEQUENCE { adslAtucPerfLofs Counter32, adslAtucPerfLoss Counter32, adslAtucPerfLols Counter32, adslAtucPerfLprs Counter32, adslAtucPerfESs Counter32, adslAtucPerfInits Counter32, adslAtucPerfValidIntervals INTEGER, adslAtucPerfInvalidIntervals INTEGER, adslAtucPerfCurr15MinTimeElapsed AdslPerfTimeElapsed, adslAtucPerfCurr15MinLofs PerfCurrentCount, adslAtucPerfCurr15MinLoss PerfCurrentCount, adslAtucPerfCurr15MinLols PerfCurrentCount, adslAtucPerfCurr15MinLprs PerfCurrentCount, adslAtucPerfCurr15MinESs PerfCurrentCount, adslAtucPerfCurr15MinInits PerfCurrentCount, adslAtucPerfCurr1DayTimeElapsed AdslPerfTimeElapsed, adslAtucPerfCurr1DayLofs AdslPerfCurrDayCount, adslAtucPerfCurr1DayLoss AdslPerfCurrDayCount, adslAtucPerfCurr1DayLols AdslPerfCurrDayCount, adslAtucPerfCurr1DayLprs AdslPerfCurrDayCount, adslAtucPerfCurr1DayESs AdslPerfCurrDayCount, adslAtucPerfCurr1DayInits AdslPerfCurrDayCount, adslAtucPerfPrev1DayMoniSecs INTEGER, adslAtucPerfPrev1DayLofs AdslPerfPrevDayCount, adslAtucPerfPrev1DayLoss AdslPerfPrevDayCount, adslAtucPerfPrev1DayLols AdslPerfPrevDayCount, adslAtucPerfPrev1DayLprs AdslPerfPrevDayCount, adslAtucPerfPrev1DayESs AdslPerfPrevDayCount, adslAtucPerfPrev1DayInits AdslPerfPrevDayCount } -- Event Counters -- -- Also see adslAtucIntervalTable for 15 minute interval -- elapsed counters. -- adslAtucPerfLofs OBJECT-TYPE SYNTAX Counter32 Bathrick & Ly Standards Track [Page 35] RFC 2662 ADSL Line MIB August 1999 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of Loss of Framing failures since agent reset." ::= { adslAtucPerfDataEntry 1 } adslAtucPerfLoss OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of Loss of Signal failures since agent reset." ::= { adslAtucPerfDataEntry 2 } adslAtucPerfLols OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of Loss of Link failures since agent reset." ::= { adslAtucPerfDataEntry 3 } adslAtucPerfLprs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of Loss of Power failures since agent reset." ::= { adslAtucPerfDataEntry 4 } adslAtucPerfESs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of Errored Seconds since agent reset. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects." ::= { adslAtucPerfDataEntry 5 } adslAtucPerfInits OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only Bathrick & Ly Standards Track [Page 36] RFC 2662 ADSL Line MIB August 1999 STATUS current DESCRIPTION "Count of the line initialization attempts since agent reset. Includes both successful and failed attempts." ::= { adslAtucPerfDataEntry 6 } -- general 15 min interval information -- adslAtucPerfValidIntervals OBJECT-TYPE SYNTAX INTEGER(0..96) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of previous 15-minute intervals in the interval table for which data was collected. Given that <n> is the maximum # of intervals supported. The value will be <n> unless the measurement was (re-)started within the last (<n>*15) minutes, in which case the value will be the number of complete 15 minute intervals for which the agent has at least some data. In certain cases (e.g., in the case where the agent is a proxy) it is possible that some intervals are unavailable. In this case, this interval is the maximum interval number for which data is available." ::= { adslAtucPerfDataEntry 7 } adslAtucPerfInvalidIntervals OBJECT-TYPE SYNTAX INTEGER(0..96) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of intervals in the range from 0 to the value of adslAtucPerfValidIntervals for which no data is available. This object will typically be zero except in cases where the data for some intervals are not available (e.g., in proxy situations)." ::= { adslAtucPerfDataEntry 8 } -- 15 min current performance group -- adslAtucPerfCurr15MinTimeElapsed OBJECT-TYPE SYNTAX AdslPerfTimeElapsed(0..899) UNITS "seconds" MAX-ACCESS read-only Bathrick & Ly Standards Track [Page 37] RFC 2662 ADSL Line MIB August 1999 STATUS current DESCRIPTION "Total elapsed seconds in this interval." ::= { adslAtucPerfDataEntry 9 } adslAtucPerfCurr15MinLofs OBJECT-TYPE SYNTAX PerfCurrentCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the current 15 minute interval when there was Loss of Framing." ::= { adslAtucPerfDataEntry 10 } adslAtucPerfCurr15MinLoss OBJECT-TYPE SYNTAX PerfCurrentCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the current 15 minute interval when there was Loss of Signal." ::= { adslAtucPerfDataEntry 11 } adslAtucPerfCurr15MinLols OBJECT-TYPE SYNTAX PerfCurrentCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the current 15 minute interval when there was Loss of Link." ::= { adslAtucPerfDataEntry 12 } adslAtucPerfCurr15MinLprs OBJECT-TYPE SYNTAX PerfCurrentCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the current 15 minute interval when there was Loss of Power." ::= { adslAtucPerfDataEntry 13 } adslAtucPerfCurr15MinESs OBJECT-TYPE SYNTAX PerfCurrentCount UNITS "seconds" Bathrick & Ly Standards Track [Page 38] RFC 2662 ADSL Line MIB August 1999 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds in the current 15 minute interval. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects." ::= { adslAtucPerfDataEntry 14 } adslAtucPerfCurr15MinInits OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the line initialization attempts in the current 15 minute interval. Includes both successful and failed attempts." ::= { adslAtucPerfDataEntry 15 } -- 1-day current and previous performance group -- adslAtucPerfCurr1DayTimeElapsed OBJECT-TYPE SYNTAX AdslPerfTimeElapsed(0..86399) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of seconds that have elapsed since the beginning of the current 1-day interval." ::= { adslAtucPerfDataEntry 16 } adslAtucPerfCurr1DayLofs OBJECT-TYPE SYNTAX AdslPerfCurrDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of seconds when there was Loss of Framing during the current day as measured by adslAtucPerfCurr1DayTimeElapsed." ::= { adslAtucPerfDataEntry 17 } adslAtucPerfCurr1DayLoss OBJECT-TYPE SYNTAX AdslPerfCurrDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION Bathrick & Ly Standards Track [Page 39] RFC 2662 ADSL Line MIB August 1999 "Count of the number of seconds when there was Loss of Signal during the current day as measured by adslAtucPerfCurr1DayTimeElapsed." ::= { adslAtucPerfDataEntry 18 } adslAtucPerfCurr1DayLols OBJECT-TYPE SYNTAX AdslPerfCurrDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of seconds when there was Loss of Link during the current day as measured by adslAtucPerfCurr1DayTimeElapsed." ::= { adslAtucPerfDataEntry 19 } adslAtucPerfCurr1DayLprs OBJECT-TYPE SYNTAX AdslPerfCurrDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of seconds when there was Loss of Power during the current day as measured by adslAtucPerfCurr1DayTimeElapsed." ::= { adslAtucPerfDataEntry 20 } adslAtucPerfCurr1DayESs OBJECT-TYPE SYNTAX AdslPerfCurrDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds during the current day as measured by adslAtucPerfCurr1DayTimeElapsed. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects." ::= { adslAtucPerfDataEntry 21 } adslAtucPerfCurr1DayInits OBJECT-TYPE SYNTAX AdslPerfCurrDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the line initialization attempts in the day as measured by adslAtucPerfCurr1DayTimeElapsed. Includes both successful and failed attempts." Bathrick & Ly Standards Track [Page 40] RFC 2662 ADSL Line MIB August 1999 ::= { adslAtucPerfDataEntry 22 } adslAtucPerfPrev1DayMoniSecs OBJECT-TYPE SYNTAX INTEGER(0..86400) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The amount of time in the previous 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason." ::= { adslAtucPerfDataEntry 23 } adslAtucPerfPrev1DayLofs OBJECT-TYPE SYNTAX AdslPerfPrevDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Framing within the most recent previous 1-day period." ::= { adslAtucPerfDataEntry 24 } adslAtucPerfPrev1DayLoss OBJECT-TYPE SYNTAX AdslPerfPrevDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Signal within the most recent previous 1-day period." ::= { adslAtucPerfDataEntry 25 } adslAtucPerfPrev1DayLols OBJECT-TYPE SYNTAX AdslPerfPrevDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Link within the most recent previous 1-day period." ::= { adslAtucPerfDataEntry 26 } Bathrick & Ly Standards Track [Page 41] RFC 2662 ADSL Line MIB August 1999 adslAtucPerfPrev1DayLprs OBJECT-TYPE SYNTAX AdslPerfPrevDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Power within the most recent previous 1-day period." ::= { adslAtucPerfDataEntry 27 } adslAtucPerfPrev1DayESs OBJECT-TYPE SYNTAX AdslPerfPrevDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds within the most recent previous 1-day period. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects." ::= { adslAtucPerfDataEntry 28 } adslAtucPerfPrev1DayInits OBJECT-TYPE SYNTAX AdslPerfPrevDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the line initialization attempts in the most recent previous 1-day period. Includes both successful and failed attempts." ::= { adslAtucPerfDataEntry 29 } adslAturPerfDataTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAturPerfDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUR. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94)." ::= { adslMibObjects 7 } adslAturPerfDataEntry OBJECT-TYPE SYNTAX AdslAturPerfDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in adslAturPerfDataTable." Bathrick & Ly Standards Track [Page 42] RFC 2662 ADSL Line MIB August 1999 INDEX { ifIndex } ::= { adslAturPerfDataTable 1 } AdslAturPerfDataEntry ::= SEQUENCE { adslAturPerfLofs Counter32, adslAturPerfLoss Counter32, adslAturPerfLprs Counter32, adslAturPerfESs Counter32, adslAturPerfValidIntervals INTEGER, adslAturPerfInvalidIntervals INTEGER, adslAturPerfCurr15MinTimeElapsed AdslPerfTimeElapsed, adslAturPerfCurr15MinLofs PerfCurrentCount, adslAturPerfCurr15MinLoss PerfCurrentCount, adslAturPerfCurr15MinLprs PerfCurrentCount, adslAturPerfCurr15MinESs PerfCurrentCount, adslAturPerfCurr1DayTimeElapsed AdslPerfTimeElapsed, adslAturPerfCurr1DayLofs AdslPerfCurrDayCount, adslAturPerfCurr1DayLoss AdslPerfCurrDayCount, adslAturPerfCurr1DayLprs AdslPerfCurrDayCount, adslAturPerfCurr1DayESs AdslPerfCurrDayCount, adslAturPerfPrev1DayMoniSecs INTEGER, adslAturPerfPrev1DayLofs AdslPerfPrevDayCount, adslAturPerfPrev1DayLoss AdslPerfPrevDayCount, adslAturPerfPrev1DayLprs AdslPerfPrevDayCount, adslAturPerfPrev1DayESs AdslPerfPrevDayCount } -- Event (Raw) Counters -- -- Also see adslAturIntervalTable for 15 minute interval -- elapsed counters. -- adslAturPerfLofs OBJECT-TYPE SYNTAX Counter32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of Loss of Framing failures since agent reset." ::= { adslAturPerfDataEntry 1 } adslAturPerfLoss OBJECT-TYPE SYNTAX Counter32 UNITS "seconds" MAX-ACCESS read-only STATUS current Bathrick & Ly Standards Track [Page 43] RFC 2662 ADSL Line MIB August 1999 DESCRIPTION "Count of the number of Loss of Signal failures since agent reset." ::= { adslAturPerfDataEntry 2 } adslAturPerfLprs OBJECT-TYPE SYNTAX Counter32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of Loss of Power failures since agent reset." ::= { adslAturPerfDataEntry 3 } adslAturPerfESs OBJECT-TYPE SYNTAX Counter32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of Errored Seconds since agent reset. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects." ::= { adslAturPerfDataEntry 4 } -- general 15 min interval information -- adslAturPerfValidIntervals OBJECT-TYPE SYNTAX INTEGER(0..96) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of previous 15-minute intervals in the interval table for which data was collected. Given that <n> is the maximum # of intervals supported. The value will be <n> unless the measurement was (re-)started within the last (<n>*15) minutes, in which case the value will be the number of complete 15 minute intervals for which the agent has at least some data. In certain cases (e.g., in the case where the agent is a proxy) it is possible that some intervals are unavailable. In this case, this interval is the maximum interval number for which data is available." ::= { adslAturPerfDataEntry 5 } Bathrick & Ly Standards Track [Page 44] RFC 2662 ADSL Line MIB August 1999 adslAturPerfInvalidIntervals OBJECT-TYPE SYNTAX INTEGER(0..96) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of intervals in the range from 0 to the value of adslAturPerfValidIntervals for which no data is available. This object will typically be zero except in cases where the data for some intervals are not available (e.g., in proxy situations)." ::= { adslAturPerfDataEntry 6 } -- 15 min current performance group -- adslAturPerfCurr15MinTimeElapsed OBJECT-TYPE SYNTAX AdslPerfTimeElapsed(0..899) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Total elapsed seconds in this interval." ::= { adslAturPerfDataEntry 7 } adslAturPerfCurr15MinLofs OBJECT-TYPE SYNTAX PerfCurrentCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the current 15 minute interval when there was Loss of Framing." ::= { adslAturPerfDataEntry 8 } adslAturPerfCurr15MinLoss OBJECT-TYPE SYNTAX PerfCurrentCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the current 15 minute interval when there was Loss of Signal." ::= { adslAturPerfDataEntry 9 } adslAturPerfCurr15MinLprs OBJECT-TYPE SYNTAX PerfCurrentCount UNITS "seconds" MAX-ACCESS read-only Bathrick & Ly Standards Track [Page 45] RFC 2662 ADSL Line MIB August 1999 STATUS current DESCRIPTION "Count of seconds in the current 15 minute interval when there was Loss of Power." ::= { adslAturPerfDataEntry 10 } adslAturPerfCurr15MinESs OBJECT-TYPE SYNTAX PerfCurrentCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds in the current 15 minute interval. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects." ::= { adslAturPerfDataEntry 11 } -- 1-day current and previous performance group -- adslAturPerfCurr1DayTimeElapsed OBJECT-TYPE SYNTAX AdslPerfTimeElapsed(0..86399) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of seconds that have elapsed since the beginning of the current 1-day interval." ::= { adslAturPerfDataEntry 12 } adslAturPerfCurr1DayLofs OBJECT-TYPE SYNTAX AdslPerfCurrDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of seconds when there was Loss of Framing during the current day as measured by adslAturPerfCurr1DayTimeElapsed." ::= { adslAturPerfDataEntry 13 } adslAturPerfCurr1DayLoss OBJECT-TYPE SYNTAX AdslPerfCurrDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION Bathrick & Ly Standards Track [Page 46] RFC 2662 ADSL Line MIB August 1999 "Count of the number of seconds when there was Loss of Signal during the current day as measured by adslAturPerfCurr1DayTimeElapsed." ::= { adslAturPerfDataEntry 14 } adslAturPerfCurr1DayLprs OBJECT-TYPE SYNTAX AdslPerfCurrDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of seconds when there was Loss of Power during the current day as measured by adslAturPerfCurr1DayTimeElapsed." ::= { adslAturPerfDataEntry 15 } adslAturPerfCurr1DayESs OBJECT-TYPE SYNTAX AdslPerfCurrDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds during the current day as measured by adslAturPerfCurr1DayTimeElapsed. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects." ::= { adslAturPerfDataEntry 16 } adslAturPerfPrev1DayMoniSecs OBJECT-TYPE SYNTAX INTEGER(0..86400) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The amount of time in the previous 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason." ::= { adslAturPerfDataEntry 17 } adslAturPerfPrev1DayLofs OBJECT-TYPE SYNTAX AdslPerfPrevDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current Bathrick & Ly Standards Track [Page 47] RFC 2662 ADSL Line MIB August 1999 DESCRIPTION "Count of seconds in the interval when there was Loss of Framing within the most recent previous 1-day period." ::= { adslAturPerfDataEntry 18 } adslAturPerfPrev1DayLoss OBJECT-TYPE SYNTAX AdslPerfPrevDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Signal within the most recent previous 1-day period." ::= { adslAturPerfDataEntry 19 } adslAturPerfPrev1DayLprs OBJECT-TYPE SYNTAX AdslPerfPrevDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Power within the most recent previous 1-day period." ::= { adslAturPerfDataEntry 20 } adslAturPerfPrev1DayESs OBJECT-TYPE SYNTAX AdslPerfPrevDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds within the most recent previous 1-day period. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects." ::= { adslAturPerfDataEntry 21 } adslAtucIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAtucIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUC performance data collection interval. ADSL physical interfaces are Bathrick & Ly Standards Track [Page 48] RFC 2662 ADSL Line MIB August 1999 those ifEntries where ifType is equal to adsl(94)." ::= { adslMibObjects 8 } adslAtucIntervalEntry OBJECT-TYPE SYNTAX AdslAtucIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the adslAtucIntervalTable." INDEX { ifIndex, adslAtucIntervalNumber } ::= { adslAtucIntervalTable 1 } AdslAtucIntervalEntry ::= SEQUENCE { adslAtucIntervalNumber INTEGER, adslAtucIntervalLofs PerfIntervalCount, adslAtucIntervalLoss PerfIntervalCount, adslAtucIntervalLols PerfIntervalCount, adslAtucIntervalLprs PerfIntervalCount, adslAtucIntervalESs PerfIntervalCount, adslAtucIntervalInits PerfIntervalCount, adslAtucIntervalValidData TruthValue } adslAtucIntervalNumber OBJECT-TYPE SYNTAX INTEGER(1..96) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Performance Data Interval number 1 is the the most recent previous interval; interval 96 is 24 hours ago. Intervals 2..96 are optional." ::= { adslAtucIntervalEntry 1 } adslAtucIntervalLofs OBJECT-TYPE SYNTAX PerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Framing." ::= { adslAtucIntervalEntry 2 } adslAtucIntervalLoss OBJECT-TYPE SYNTAX PerfIntervalCount UNITS "seconds" MAX-ACCESS read-only Bathrick & Ly Standards Track [Page 49] RFC 2662 ADSL Line MIB August 1999 STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Signal." ::= { adslAtucIntervalEntry 3 } adslAtucIntervalLols OBJECT-TYPE SYNTAX PerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Link." ::= { adslAtucIntervalEntry 4 } adslAtucIntervalLprs OBJECT-TYPE SYNTAX PerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Power." ::= { adslAtucIntervalEntry 5 } adslAtucIntervalESs OBJECT-TYPE SYNTAX PerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds in the interval. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects." ::= { adslAtucIntervalEntry 6 } adslAtucIntervalInits OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the line initialization attempts during the interval. Includes both successful and failed attempts." ::= { adslAtucIntervalEntry 7 } Bathrick & Ly Standards Track [Page 50] RFC 2662 ADSL Line MIB August 1999 adslAtucIntervalValidData OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates if the data for this interval is valid." ::= { adslAtucIntervalEntry 8 } adslAturIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAturIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUR performance data collection interval. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94)." ::= { adslMibObjects 9 } adslAturIntervalEntry OBJECT-TYPE SYNTAX AdslAturIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the adslAturIntervalTable." INDEX { ifIndex, adslAturIntervalNumber } ::= { adslAturIntervalTable 1 } AdslAturIntervalEntry ::= SEQUENCE { adslAturIntervalNumber INTEGER, adslAturIntervalLofs PerfIntervalCount, adslAturIntervalLoss PerfIntervalCount, adslAturIntervalLprs PerfIntervalCount, adslAturIntervalESs PerfIntervalCount, adslAturIntervalValidData TruthValue } adslAturIntervalNumber OBJECT-TYPE SYNTAX INTEGER(1..96) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Performance Data Interval number 1 is the the most recent previous interval; interval 96 is 24 hours ago. Intervals 2..96 are optional." ::= { adslAturIntervalEntry 1 } Bathrick & Ly Standards Track [Page 51] RFC 2662 ADSL Line MIB August 1999 adslAturIntervalLofs OBJECT-TYPE SYNTAX PerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Framing." ::= { adslAturIntervalEntry 2 } adslAturIntervalLoss OBJECT-TYPE SYNTAX PerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Signal." ::= { adslAturIntervalEntry 3 } adslAturIntervalLprs OBJECT-TYPE SYNTAX PerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Power." ::= { adslAturIntervalEntry 4 } adslAturIntervalESs OBJECT-TYPE SYNTAX PerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds in the interval. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects." ::= { adslAturIntervalEntry 5 } adslAturIntervalValidData OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates if the data for this Bathrick & Ly Standards Track [Page 52] RFC 2662 ADSL Line MIB August 1999 interval is valid." ::= { adslAturIntervalEntry 6 } adslAtucChanPerfDataTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAtucChanPerfDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUC channel. ADSL channel interfaces are those ifEntries where ifType is equal to adslInterleave(124) or adslFast(125)." ::= { adslMibObjects 10 } adslAtucChanPerfDataEntry OBJECT-TYPE SYNTAX AdslAtucChanPerfDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in adslAtucChanPerfDataTable." INDEX { ifIndex } ::= { adslAtucChanPerfDataTable 1 } AdslAtucChanPerfDataEntry ::= SEQUENCE { adslAtucChanReceivedBlks Counter32, adslAtucChanTransmittedBlks Counter32, adslAtucChanCorrectedBlks Counter32, adslAtucChanUncorrectBlks Counter32, adslAtucChanPerfValidIntervals INTEGER, adslAtucChanPerfInvalidIntervals INTEGER, adslAtucChanPerfCurr15MinTimeElapsed AdslPerfTimeElapsed, adslAtucChanPerfCurr15MinReceivedBlks PerfCurrentCount, adslAtucChanPerfCurr15MinTransmittedBlks PerfCurrentCount, adslAtucChanPerfCurr15MinCorrectedBlks PerfCurrentCount, adslAtucChanPerfCurr15MinUncorrectBlks PerfCurrentCount, adslAtucChanPerfCurr1DayTimeElapsed AdslPerfTimeElapsed, adslAtucChanPerfCurr1DayReceivedBlks AdslPerfCurrDayCount, adslAtucChanPerfCurr1DayTransmittedBlks AdslPerfCurrDayCount, adslAtucChanPerfCurr1DayCorrectedBlks AdslPerfCurrDayCount, adslAtucChanPerfCurr1DayUncorrectBlks AdslPerfCurrDayCount, adslAtucChanPerfPrev1DayMoniSecs INTEGER, adslAtucChanPerfPrev1DayReceivedBlks AdslPerfPrevDayCount, adslAtucChanPerfPrev1DayTransmittedBlks AdslPerfPrevDayCount, adslAtucChanPerfPrev1DayCorrectedBlks AdslPerfPrevDayCount, adslAtucChanPerfPrev1DayUncorrectBlks AdslPerfPrevDayCount } -- performance group Bathrick & Ly Standards Track [Page 53] RFC 2662 ADSL Line MIB August 1999 -- -- Note: block is intended to be the length of the channel -- data-block on which the CRC operates. See -- adslAtucChanCrcBlockLength for more information. -- adslAtucChanReceivedBlks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks received on this channel since agent reset." ::= { adslAtucChanPerfDataEntry 1 } adslAtucChanTransmittedBlks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks transmitted on this channel since agent reset." ::= { adslAtucChanPerfDataEntry 2 } adslAtucChanCorrectedBlks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with errors that were corrected since agent reset. These blocks are passed on as good data." ::= { adslAtucChanPerfDataEntry 3 } adslAtucChanUncorrectBlks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with uncorrectable errors since agent reset." ::= { adslAtucChanPerfDataEntry 4 } -- general 15 min interval information -- adslAtucChanPerfValidIntervals OBJECT-TYPE SYNTAX INTEGER(0..96) MAX-ACCESS read-only STATUS current Bathrick & Ly Standards Track [Page 54] RFC 2662 ADSL Line MIB August 1999 DESCRIPTION "The number of previous 15-minute intervals in the interval table for which data was collected. Given that <n> is the maximum # of intervals supported. The value will be <n> unless the measurement was (re-)started within the last (<n>*15) minutes, in which case the value will be the number of complete 15 minute intervals for which the agent has at least some data. In certain cases (e.g., in the case where the agent is a proxy) it is possible that some intervals are unavailable. In this case, this interval is the maximum interval number for which data is available." ::= { adslAtucChanPerfDataEntry 5 } adslAtucChanPerfInvalidIntervals OBJECT-TYPE SYNTAX INTEGER(0..96) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of intervals in the range from 0 to the value of adslAtucChanPerfValidIntervals for which no data is available. This object will typically be zero except in cases where the data for some intervals are not available (e.g., in proxy situations)." ::= { adslAtucChanPerfDataEntry 6 } -- 15 min current performance group -- adslAtucChanPerfCurr15MinTimeElapsed OBJECT-TYPE SYNTAX AdslPerfTimeElapsed(0..899) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Total elapsed seconds in this interval." ::= { adslAtucChanPerfDataEntry 7 } adslAtucChanPerfCurr15MinReceivedBlks OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks received on this channel within the current 15 minute interval." ::= { adslAtucChanPerfDataEntry 8 } Bathrick & Ly Standards Track [Page 55] RFC 2662 ADSL Line MIB August 1999 adslAtucChanPerfCurr15MinTransmittedBlks OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks transmitted on this channel within the current 15 minute interval." ::= { adslAtucChanPerfDataEntry 9 } adslAtucChanPerfCurr15MinCorrectedBlks OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with errors that were corrected on this channel within the current 15 minute interval." ::= { adslAtucChanPerfDataEntry 10 } adslAtucChanPerfCurr15MinUncorrectBlks OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with uncorrectable errors on this channel within the current 15 minute interval." ::= { adslAtucChanPerfDataEntry 11 } -- 1-day current and previous performance group -- adslAtucChanPerfCurr1DayTimeElapsed OBJECT-TYPE SYNTAX AdslPerfTimeElapsed(0..86399) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of seconds that have elapsed since the beginning of the current 1-day interval." ::= { adslAtucChanPerfDataEntry 12 } adslAtucChanPerfCurr1DayReceivedBlks OBJECT-TYPE SYNTAX AdslPerfCurrDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks received on this channel during the current day as measured by Bathrick & Ly Standards Track [Page 56] RFC 2662 ADSL Line MIB August 1999 adslAtucChanPerfCurr1DayTimeElapsed." ::= { adslAtucChanPerfDataEntry 13 } adslAtucChanPerfCurr1DayTransmittedBlks OBJECT-TYPE SYNTAX AdslPerfCurrDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks transmitted on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed." ::= { adslAtucChanPerfDataEntry 14 } adslAtucChanPerfCurr1DayCorrectedBlks OBJECT-TYPE SYNTAX AdslPerfCurrDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with errors that were corrected on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed." ::= { adslAtucChanPerfDataEntry 15 } adslAtucChanPerfCurr1DayUncorrectBlks OBJECT-TYPE SYNTAX AdslPerfCurrDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with uncorrectable errors on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed." ::= { adslAtucChanPerfDataEntry 16 } adslAtucChanPerfPrev1DayMoniSecs OBJECT-TYPE SYNTAX INTEGER(0..86400) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The amount of time in the previous 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason." ::= { adslAtucChanPerfDataEntry 17 } adslAtucChanPerfPrev1DayReceivedBlks OBJECT-TYPE Bathrick & Ly Standards Track [Page 57] RFC 2662 ADSL Line MIB August 1999 SYNTAX AdslPerfPrevDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks received on this channel within the most recent previous 1-day period." ::= { adslAtucChanPerfDataEntry 18 } adslAtucChanPerfPrev1DayTransmittedBlks OBJECT-TYPE SYNTAX AdslPerfPrevDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks transmitted on this channel within the most recent previous 1-day period." ::= { adslAtucChanPerfDataEntry 19 } adslAtucChanPerfPrev1DayCorrectedBlks OBJECT-TYPE SYNTAX AdslPerfPrevDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with errors that were corrected on this channel within the most recent previous 1-day period." ::= { adslAtucChanPerfDataEntry 20 } adslAtucChanPerfPrev1DayUncorrectBlks OBJECT-TYPE SYNTAX AdslPerfPrevDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with uncorrectable errors on this channel within the most recent previous 1-day period." ::= { adslAtucChanPerfDataEntry 21 } adslAturChanPerfDataTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAturChanPerfDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUR channel. ADSL channel interfaces are those ifEntries where ifType is equal to adslInterleave(124) or adslFast(125)." Bathrick & Ly Standards Track [Page 58] RFC 2662 ADSL Line MIB August 1999 ::= { adslMibObjects 11 } adslAturChanPerfDataEntry OBJECT-TYPE SYNTAX AdslAturChanPerfDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in adslAturChanPerfDataTable." INDEX { ifIndex } ::= { adslAturChanPerfDataTable 1 } AdslAturChanPerfDataEntry ::= SEQUENCE { adslAturChanReceivedBlks Counter32, adslAturChanTransmittedBlks Counter32, adslAturChanCorrectedBlks Counter32, adslAturChanUncorrectBlks Counter32, adslAturChanPerfValidIntervals INTEGER, adslAturChanPerfInvalidIntervals INTEGER, adslAturChanPerfCurr15MinTimeElapsed AdslPerfTimeElapsed, adslAturChanPerfCurr15MinReceivedBlks PerfCurrentCount, adslAturChanPerfCurr15MinTransmittedBlks PerfCurrentCount, adslAturChanPerfCurr15MinCorrectedBlks PerfCurrentCount, adslAturChanPerfCurr15MinUncorrectBlks PerfCurrentCount, adslAturChanPerfCurr1DayTimeElapsed AdslPerfTimeElapsed, adslAturChanPerfCurr1DayReceivedBlks AdslPerfCurrDayCount, adslAturChanPerfCurr1DayTransmittedBlks AdslPerfCurrDayCount, adslAturChanPerfCurr1DayCorrectedBlks AdslPerfCurrDayCount, adslAturChanPerfCurr1DayUncorrectBlks AdslPerfCurrDayCount, adslAturChanPerfPrev1DayMoniSecs INTEGER, adslAturChanPerfPrev1DayReceivedBlks AdslPerfPrevDayCount, adslAturChanPerfPrev1DayTransmittedBlks AdslPerfPrevDayCount, adslAturChanPerfPrev1DayCorrectedBlks AdslPerfPrevDayCount, adslAturChanPerfPrev1DayUncorrectBlks AdslPerfPrevDayCount } -- performance group -- -- Note: block is intended to be the length of the channel -- data-block on which the CRC operates. See -- adslAturChanCrcBlockLength for more information. -- adslAturChanReceivedBlks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks received on this channel since agent reset." ::= { adslAturChanPerfDataEntry 1 } Bathrick & Ly Standards Track [Page 59] RFC 2662 ADSL Line MIB August 1999 adslAturChanTransmittedBlks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks transmitted on this channel since agent reset." ::= { adslAturChanPerfDataEntry 2 } adslAturChanCorrectedBlks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with errors that were corrected since agent reset. These blocks are passed on as good data." ::= { adslAturChanPerfDataEntry 3 } adslAturChanUncorrectBlks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with uncorrectable errors since agent reset." ::= { adslAturChanPerfDataEntry 4 } -- general 15 min interval information -- adslAturChanPerfValidIntervals OBJECT-TYPE SYNTAX INTEGER(0..96) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of previous 15-minute intervals in the interval table for which data was collected. Given that <n> is the maximum # of intervals supported. The value will be <n> unless the measurement was (re-)started within the last (<n>*15) minutes, in which case the value will be the number of complete 15 minute intervals for which the agent has at least some data. In certain cases (e.g., in the case where the agent is a proxy) it is possible that some intervals are unavailable. In this case, this interval is the maximum interval number for which data is available." ::= { adslAturChanPerfDataEntry 5 } Bathrick & Ly Standards Track [Page 60] RFC 2662 ADSL Line MIB August 1999 adslAturChanPerfInvalidIntervals OBJECT-TYPE SYNTAX INTEGER(0..96) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of intervals in the range from 0 to the value of adslAturChanPerfValidIntervals for which no data is available. This object will typically be zero except in cases where the data for some intervals are not available (e.g., in proxy situations)." ::= { adslAturChanPerfDataEntry 6 } -- 15 min current performance group -- adslAturChanPerfCurr15MinTimeElapsed OBJECT-TYPE SYNTAX AdslPerfTimeElapsed(0..899) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Total elapsed seconds in this interval. A full interval is 900 seconds." ::= { adslAturChanPerfDataEntry 7 } adslAturChanPerfCurr15MinReceivedBlks OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks received on this channel within the current 15 minute interval." ::= { adslAturChanPerfDataEntry 8 } adslAturChanPerfCurr15MinTransmittedBlks OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks transmitted on this channel within the current 15 minute interval." ::= { adslAturChanPerfDataEntry 9 } adslAturChanPerfCurr15MinCorrectedBlks OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION Bathrick & Ly Standards Track [Page 61] RFC 2662 ADSL Line MIB August 1999 "Count of all blocks received with errors that were corrected on this channel within the current 15 minute interval." ::= { adslAturChanPerfDataEntry 10 } adslAturChanPerfCurr15MinUncorrectBlks OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with uncorrectable errors on this channel within the current 15 minute interval." ::= { adslAturChanPerfDataEntry 11 } -- 1-day current and previous performance group -- adslAturChanPerfCurr1DayTimeElapsed OBJECT-TYPE SYNTAX AdslPerfTimeElapsed(0..86399) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of seconds that have elapsed since the beginning of the current 1-day interval." ::= { adslAturChanPerfDataEntry 12 } adslAturChanPerfCurr1DayReceivedBlks OBJECT-TYPE SYNTAX AdslPerfCurrDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks received on this channel during the current day as measured by adslAturChanPerfCurr1DayTimeElapsed." ::= { adslAturChanPerfDataEntry 13 } adslAturChanPerfCurr1DayTransmittedBlks OBJECT-TYPE SYNTAX AdslPerfCurrDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks transmitted on this channel during the current day as measured by adslAturChanPerfCurr1DayTimeElapsed." ::= { adslAturChanPerfDataEntry 14 } Bathrick & Ly Standards Track [Page 62] RFC 2662 ADSL Line MIB August 1999 adslAturChanPerfCurr1DayCorrectedBlks OBJECT-TYPE SYNTAX AdslPerfCurrDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with errors that were corrected on this channel during the current day as measured by adslAturChanPerfCurr1DayTimeElapsed." ::= { adslAturChanPerfDataEntry 15 } adslAturChanPerfCurr1DayUncorrectBlks OBJECT-TYPE SYNTAX AdslPerfCurrDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with uncorrectable errors on this channel during the current day as measured by adslAturChanPerfCurr1DayTimeElapsed." ::= { adslAturChanPerfDataEntry 16 } adslAturChanPerfPrev1DayMoniSecs OBJECT-TYPE SYNTAX INTEGER(0..86400) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The amount of time in the previous 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason." ::= { adslAturChanPerfDataEntry 17 } adslAturChanPerfPrev1DayReceivedBlks OBJECT-TYPE SYNTAX AdslPerfPrevDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks received on this channel within the most recent previous 1-day period." ::= { adslAturChanPerfDataEntry 18 } adslAturChanPerfPrev1DayTransmittedBlks OBJECT-TYPE SYNTAX AdslPerfPrevDayCount MAX-ACCESS read-only STATUS current Bathrick & Ly Standards Track [Page 63] RFC 2662 ADSL Line MIB August 1999 DESCRIPTION "Count of all encoded blocks transmitted on this channel within the most recent previous 1-day period." ::= { adslAturChanPerfDataEntry 19 } adslAturChanPerfPrev1DayCorrectedBlks OBJECT-TYPE SYNTAX AdslPerfPrevDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with errors that were corrected on this channel within the most recent previous 1-day period." ::= { adslAturChanPerfDataEntry 20 } adslAturChanPerfPrev1DayUncorrectBlks OBJECT-TYPE SYNTAX AdslPerfPrevDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with uncorrectable errors on this channel within the most recent previous 1-day period." ::= { adslAturChanPerfDataEntry 21 } adslAtucChanIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAtucChanIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUC channel's performance data collection interval. ADSL channel interfaces are those ifEntries where ifType is equal to adslInterleave(124) or adslFast(125)." ::= { adslMibObjects 12 } adslAtucChanIntervalEntry OBJECT-TYPE SYNTAX AdslAtucChanIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the adslAtucIntervalTable." INDEX { ifIndex, adslAtucChanIntervalNumber } ::= { adslAtucChanIntervalTable 1 } AdslAtucChanIntervalEntry ::= SEQUENCE { Bathrick & Ly Standards Track [Page 64] RFC 2662 ADSL Line MIB August 1999 adslAtucChanIntervalNumber INTEGER, adslAtucChanIntervalReceivedBlks PerfIntervalCount, adslAtucChanIntervalTransmittedBlks PerfIntervalCount, adslAtucChanIntervalCorrectedBlks PerfIntervalCount, adslAtucChanIntervalUncorrectBlks PerfIntervalCount, adslAtucChanIntervalValidData TruthValue } adslAtucChanIntervalNumber OBJECT-TYPE SYNTAX INTEGER(1..96) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Performance Data Interval number 1 is the the most recent previous interval; interval 96 is 24 hours ago. Intervals 2..96 are optional." ::= { adslAtucChanIntervalEntry 1 } adslAtucChanIntervalReceivedBlks OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks received on this channel during this interval." ::= { adslAtucChanIntervalEntry 2 } adslAtucChanIntervalTransmittedBlks OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks transmitted on this channel during this interval." ::= { adslAtucChanIntervalEntry 3 } adslAtucChanIntervalCorrectedBlks OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with errors that were corrected on this channel during this interval." ::= { adslAtucChanIntervalEntry 4 } adslAtucChanIntervalUncorrectBlks OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only Bathrick & Ly Standards Track [Page 65] RFC 2662 ADSL Line MIB August 1999 STATUS current DESCRIPTION "Count of all blocks received with uncorrectable errors on this channel during this interval." ::= { adslAtucChanIntervalEntry 5 } adslAtucChanIntervalValidData OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates if the data for this interval is valid." ::= { adslAtucChanIntervalEntry 6 } adslAturChanIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAturChanIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUR channel's performance data collection interval. ADSL channel interfaces are those ifEntries where ifType is equal to adslInterleave(124) or adslFast(125)." ::= { adslMibObjects 13 } adslAturChanIntervalEntry OBJECT-TYPE SYNTAX AdslAturChanIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the adslAturIntervalTable." INDEX { ifIndex, adslAturChanIntervalNumber } ::= { adslAturChanIntervalTable 1 } AdslAturChanIntervalEntry ::= SEQUENCE { adslAturChanIntervalNumber INTEGER, adslAturChanIntervalReceivedBlks PerfIntervalCount, adslAturChanIntervalTransmittedBlks PerfIntervalCount, adslAturChanIntervalCorrectedBlks PerfIntervalCount, adslAturChanIntervalUncorrectBlks PerfIntervalCount, adslAturChanIntervalValidData TruthValue } adslAturChanIntervalNumber OBJECT-TYPE SYNTAX INTEGER(1..96) MAX-ACCESS not-accessible STATUS current Bathrick & Ly Standards Track [Page 66] RFC 2662 ADSL Line MIB August 1999 DESCRIPTION "Performance Data Interval number 1 is the the most recent previous interval; interval 96 is 24 hours ago. Intervals 2..96 are optional." ::= { adslAturChanIntervalEntry 1 } adslAturChanIntervalReceivedBlks OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks received on this channel during this interval." ::= { adslAturChanIntervalEntry 2 } adslAturChanIntervalTransmittedBlks OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks transmitted on this channel during this interval." ::= { adslAturChanIntervalEntry 3 } adslAturChanIntervalCorrectedBlks OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with errors that were corrected on this channel during this interval." ::= { adslAturChanIntervalEntry 4 } adslAturChanIntervalUncorrectBlks OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with uncorrectable errors on this channel during this interval." ::= { adslAturChanIntervalEntry 5 } adslAturChanIntervalValidData OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION Bathrick & Ly Standards Track [Page 67] RFC 2662 ADSL Line MIB August 1999 "This variable indicates if the data for this interval is valid." ::= { adslAturChanIntervalEntry 6 } -- Profile Group -- adslLineConfProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslLineConfProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information on the ADSL line configuration. One entry in this table reflects a profile defined by a manager which can be used to configure the ADSL line." ::= { adslMibObjects 14} adslLineConfProfileEntry OBJECT-TYPE SYNTAX AdslLineConfProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry consists of a list of parameters that represents the configuration of an ADSL modem. When `dynamic' profiles are implemented, a default profile will always exist. This profile's name will be set to `DEFVAL' and its parameters will be set to vendor specific values, unless otherwise specified in this document. When `static' profiles are implemented, profiles are automaticly created or destroyed as ADSL physical lines are discovered and removed by the system. The name of the profile will be equivalent to the decimal value of the line's interface index. " INDEX { IMPLIED adslLineConfProfileName} ::= { adslLineConfProfileTable 1} AdslLineConfProfileEntry ::= SEQUENCE { adslLineConfProfileName SnmpAdminString, adslAtucConfRateMode INTEGER, adslAtucConfRateChanRatio INTEGER, adslAtucConfTargetSnrMgn INTEGER, Bathrick & Ly Standards Track [Page 68] RFC 2662 ADSL Line MIB August 1999 adslAtucConfMaxSnrMgn INTEGER, adslAtucConfMinSnrMgn INTEGER, adslAtucConfDownshiftSnrMgn INTEGER, adslAtucConfUpshiftSnrMgn INTEGER, adslAtucConfMinUpshiftTime INTEGER, adslAtucConfMinDownshiftTime INTEGER, adslAtucChanConfFastMinTxRate Unsigned32, adslAtucChanConfInterleaveMinTxRate Unsigned32, adslAtucChanConfFastMaxTxRate Unsigned32, adslAtucChanConfInterleaveMaxTxRate Unsigned32, adslAtucChanConfMaxInterleaveDelay INTEGER, adslAturConfRateMode INTEGER, adslAturConfRateChanRatio INTEGER, adslAturConfTargetSnrMgn INTEGER, adslAturConfMaxSnrMgn INTEGER, adslAturConfMinSnrMgn INTEGER, adslAturConfDownshiftSnrMgn INTEGER, adslAturConfUpshiftSnrMgn INTEGER, adslAturConfMinUpshiftTime INTEGER, adslAturConfMinDownshiftTime INTEGER, adslAturChanConfFastMinTxRate Unsigned32, adslAturChanConfInterleaveMinTxRate Unsigned32, adslAturChanConfFastMaxTxRate Unsigned32, adslAturChanConfInterleaveMaxTxRate Unsigned32, adslAturChanConfMaxInterleaveDelay INTEGER, adslLineConfProfileRowStatus RowStatus } adslLineConfProfileName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object is used by the line configuration table in order to identify a row of this table. When `dynamic' profiles are implemented, the profile name is user specified. Also, the system will always provide a default profile whose name is `DEFVAL'. When `static' profiles are implemented, there is an one-to-one relationship between each line and its profile. In which case, the profile name will need to algorithmicly represent the Line's ifIndex. Therefore, the profile's name is a decimalized string of the ifIndex that is fixed-length (i.e., 10) with leading zero(s). For example, the profile name for ifIndex which equals '15' will be '0000000015'." Bathrick & Ly Standards Track [Page 69] RFC 2662 ADSL Line MIB August 1999 ::= { adslLineConfProfileEntry 1 } adslAtucConfRateMode OBJECT-TYPE SYNTAX INTEGER { fixed (1), -- no rate adaptation adaptAtStartup (2), -- perform rate adaptation -- only at initialization adaptAtRuntime (3) -- perform rate adaptation at -- any time } MAX-ACCESS read-create STATUS current DESCRIPTION "Defines what form of transmit rate adaptation is configured on this modem. See ADSL Forum TR-005 [3] for more information." ::= { adslLineConfProfileEntry 2 } adslAtucConfRateChanRatio OBJECT-TYPE SYNTAX INTEGER(0..100) UNITS "%" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured allocation ratio of excess transmit bandwidth between fast and interleaved channels. Only applies when two channel mode and RADSL are supported. Distribute bandwidth on each channel in excess of the corresponding ChanConfMinTxRate so that: adslAtucConfRateChanRatio = [Fast / (Fast + Interleaved)] * 100 In other words this value is the fast channel percentage." ::= { adslLineConfProfileEntry 3 } adslAtucConfTargetSnrMgn OBJECT-TYPE SYNTAX INTEGER (0..310) UNITS "tenth dB" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successfully complete initialization." ::= { adslLineConfProfileEntry 4 } Bathrick & Ly Standards Track [Page 70] RFC 2662 ADSL Line MIB August 1999 adslAtucConfMaxSnrMgn OBJECT-TYPE SYNTAX INTEGER (0..310) UNITS "tenth dB" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Maximum acceptable Signal/Noise Margin. If the Noise Margin is above this the modem should attempt to reduce its power output to optimize its operation." ::= { adslLineConfProfileEntry 5 } adslAtucConfMinSnrMgn OBJECT-TYPE SYNTAX INTEGER (0..310) UNITS "tenth dB" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Minimum acceptable Signal/Noise Margin. If the noise margin falls below this level, the modem should attempt to increase its power output. If that is not possible the modem will attempt to re-initialize or shut down." ::= { adslLineConfProfileEntry 6 } adslAtucConfDownshiftSnrMgn OBJECT-TYPE SYNTAX INTEGER (0..310) UNITS "tenth dB" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Signal/Noise Margin for rate downshift. If the noise margin falls below this level, the modem should attempt to decrease its transmit rate. In the case that RADSL mode is not present, the value will be `0'." ::= { adslLineConfProfileEntry 7 } adslAtucConfUpshiftSnrMgn OBJECT-TYPE SYNTAX INTEGER (0..310) UNITS "tenth dB" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Signal/Noise Margin for rate upshift. If the noise margin rises above this level, the modem should attempt to increase its transmit rate. In the case that RADSL is not present, the value will Bathrick & Ly Standards Track [Page 71] RFC 2662 ADSL Line MIB August 1999 be `0'." ::= { adslLineConfProfileEntry 8 } adslAtucConfMinUpshiftTime OBJECT-TYPE SYNTAX INTEGER(0..16383) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Minimum time that the current margin is above UpshiftSnrMgn before an upshift occurs. In the case that RADSL is not present, the value will be `0'." ::= { adslLineConfProfileEntry 9 } adslAtucConfMinDownshiftTime OBJECT-TYPE SYNTAX INTEGER(0..16383) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Minimum time that the current margin is below DownshiftSnrMgn before a downshift occurs. In the case that RADSL mode is not present, the value will be `0'." ::= { adslLineConfProfileEntry 10 } adslAtucChanConfFastMinTxRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Minimum Transmit rate for `Fast' channels, in bps. See adslAtucConfRateChanRatio for information regarding RADSL mode and ATUR transmit rate for ATUC receive rates." ::= { adslLineConfProfileEntry 11 } adslAtucChanConfInterleaveMinTxRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Minimum Transmit rate for `Interleave' channels, in bps. See adslAtucConfRateChanRatio for information regarding RADSL mode and see ATUR transmit rate for receive rates." Bathrick & Ly Standards Track [Page 72] RFC 2662 ADSL Line MIB August 1999 ::= { adslLineConfProfileEntry 12 } adslAtucChanConfFastMaxTxRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Maximum Transmit rate for `Fast' channels, in bps. See adslAtucConfRateChanRatio for information regarding RADSL mode and see ATUR transmit rate for ATUC receive rates." ::= { adslLineConfProfileEntry 13 } adslAtucChanConfInterleaveMaxTxRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Maximum Transmit rate for `Interleave' channels, in bps. See adslAtucConfRateChanRatio for information regarding RADSL mode and ATUR transmit rate for ATUC receive rates." ::= { adslLineConfProfileEntry 14 } adslAtucChanConfMaxInterleaveDelay OBJECT-TYPE SYNTAX INTEGER(0..255) UNITS "milli-seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured maximum Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency." ::= { adslLineConfProfileEntry 15 } adslAturConfRateMode OBJECT-TYPE SYNTAX INTEGER { fixed (1), -- no rate adaptation adaptAtStartup (2), -- perform rate adaptation Bathrick & Ly Standards Track [Page 73] RFC 2662 ADSL Line MIB August 1999 -- only at initialization adaptAtRuntime (3) -- perform rate adaptation at -- any time } MAX-ACCESS read-create STATUS current DESCRIPTION "Defines what form of transmit rate adaptation is configured on this modem. See ADSL Forum TR-005 [3] for more information." ::= { adslLineConfProfileEntry 16 } adslAturConfRateChanRatio OBJECT-TYPE SYNTAX INTEGER(0..100) UNITS "%" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured allocation ratio of excess transmit bandwidth between fast and interleaved channels. Only applies when two channel mode and RADSL are supported. Distribute bandwidth on each channel in excess of the corresponding ChanConfMinTxRate so that: adslAturConfRateChanRatio = [Fast / (Fast + Interleaved)] * 100 In other words this value is the fast channel percentage." ::= { adslLineConfProfileEntry 17 } adslAturConfTargetSnrMgn OBJECT-TYPE SYNTAX INTEGER (0..310) UNITS "tenth dB" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successfully complete initialization." ::= { adslLineConfProfileEntry 18 } adslAturConfMaxSnrMgn OBJECT-TYPE SYNTAX INTEGER (0..310) UNITS "tenth dB" MAX-ACCESS read-create STATUS current Bathrick & Ly Standards Track [Page 74] RFC 2662 ADSL Line MIB August 1999 DESCRIPTION "Configured Maximum acceptable Signal/Noise Margin. If the Noise Margin is above this the modem should attempt to reduce its power output to optimize its operation." ::= { adslLineConfProfileEntry 19 } adslAturConfMinSnrMgn OBJECT-TYPE SYNTAX INTEGER (0..310) UNITS "tenth dB" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Minimum acceptable Signal/Noise Margin. If the noise margin falls below this level, the modem should attempt to increase its power output. If that is not possible the modem will attempt to re-initialize or shut down." ::= { adslLineConfProfileEntry 20 } adslAturConfDownshiftSnrMgn OBJECT-TYPE SYNTAX INTEGER (0..310) UNITS "tenth dB" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Signal/Noise Margin for rate downshift. If the noise margin falls below this level, the modem should attempt to decrease its transmit rate. In the case that RADSL mode is not present, the value will be `0'." ::= { adslLineConfProfileEntry 21 } adslAturConfUpshiftSnrMgn OBJECT-TYPE SYNTAX INTEGER (0..310) UNITS "tenth dB" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Signal/Noise Margin for rate upshift. If the noise margin rises above this level, the modem should attempt to increase its transmit rate. In the case that RADSL is not present, the value will be `0'." ::= { adslLineConfProfileEntry 22 } adslAturConfMinUpshiftTime OBJECT-TYPE SYNTAX INTEGER(0..16383) Bathrick & Ly Standards Track [Page 75] RFC 2662 ADSL Line MIB August 1999 UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Minimum time that the current margin is above UpshiftSnrMgn before an upshift occurs. In the case that RADSL is not present, the value will be `0'." ::= { adslLineConfProfileEntry 23 } adslAturConfMinDownshiftTime OBJECT-TYPE SYNTAX INTEGER(0..16383) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Minimum time that the current margin is below DownshiftSnrMgn before a downshift occurs. In the case that RADSL mode is not present, the value will be `0'." ::= { adslLineConfProfileEntry 24 } adslAturChanConfFastMinTxRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Minimum Transmit rate for `Fast' channels, in bps. See adslAturConfRateChanRatio for information regarding RADSL mode and ATUC transmit rate for ATUR receive rates." ::= { adslLineConfProfileEntry 25 } adslAturChanConfInterleaveMinTxRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Minimum Transmit rate for `Interleave' channels, in bps. See adslAturConfRateChanRatio for information regarding RADSL mode and ATUC transmit rate for ATUR receive rates." ::= { adslLineConfProfileEntry 26 } adslAturChanConfFastMaxTxRate OBJECT-TYPE SYNTAX Unsigned32 Bathrick & Ly Standards Track [Page 76] RFC 2662 ADSL Line MIB August 1999 UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Maximum Transmit rate for `Fast' channels, in bps. See adslAturConfRateChanRatio for information regarding RADSL mode and ATUC transmit rate for ATUR receive rates." ::= { adslLineConfProfileEntry 27 } adslAturChanConfInterleaveMaxTxRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Maximum Transmit rate for `Interleave' channels, in bps. See adslAturConfRateChanRatio for information regarding RADSL mode and see ATUC transmit rate for ATUR receive rates." ::= { adslLineConfProfileEntry 28 } adslAturChanConfMaxInterleaveDelay OBJECT-TYPE SYNTAX INTEGER(0..255) UNITS "milli-seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured maximum Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency." ::= { adslLineConfProfileEntry 29 } adslLineConfProfileRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or modify or delete an existing row in this table. Bathrick & Ly Standards Track [Page 77] RFC 2662 ADSL Line MIB August 1999 A profile activated by setting this object to `active'. When `active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service, (by setting this object to `destroy' or `outOfService') it must be first unreferenced from all associated lines. If the implementator of this MIB has chosen not to implement `dynamic assignment' of profiles, this object's MIN-ACCESS is read-only and its value is always to be `active'." ::= { adslLineConfProfileEntry 30 } adslLineAlarmConfProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslLineAlarmConfProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information on the ADSL line configuration. One entry in this table reflects a profile defined by a manager which can be used to configure the modem for a physical line" ::= { adslMibObjects 15} adslLineAlarmConfProfileEntry OBJECT-TYPE SYNTAX AdslLineAlarmConfProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry consists of a list of parameters that represents the configuration of an ADSL modem. When `dynamic' profiles are implemented, a default profile will always exist. This profile's name will be set to `DEFVAL' and its parameters will be set to vendor specific values, unless otherwise specified in this document. When `static' profiles are implemented, profiles are automaticly created or destroyed as ADSL physical lines are discovered and removed by the system. The name of the profile will be equivalent to the decimal value of the line's interface index. " INDEX { IMPLIED adslLineAlarmConfProfileName} Bathrick & Ly Standards Track [Page 78] RFC 2662 ADSL Line MIB August 1999 ::= { adslLineAlarmConfProfileTable 1} AdslLineAlarmConfProfileEntry ::= SEQUENCE { adslLineAlarmConfProfileName SnmpAdminString, adslAtucThresh15MinLofs INTEGER, adslAtucThresh15MinLoss INTEGER, adslAtucThresh15MinLols INTEGER, adslAtucThresh15MinLprs INTEGER, adslAtucThresh15MinESs INTEGER, adslAtucThreshFastRateUp Unsigned32, adslAtucThreshInterleaveRateUp Unsigned32, adslAtucThreshFastRateDown Unsigned32, adslAtucThreshInterleaveRateDown Unsigned32, adslAtucInitFailureTrapEnable INTEGER, adslAturThresh15MinLofs INTEGER, adslAturThresh15MinLoss INTEGER, adslAturThresh15MinLprs INTEGER, adslAturThresh15MinESs INTEGER, adslAturThreshFastRateUp Unsigned32, adslAturThreshInterleaveRateUp Unsigned32, adslAturThreshFastRateDown Unsigned32, adslAturThreshInterleaveRateDown Unsigned32, adslLineAlarmConfProfileRowStatus RowStatus } adslLineAlarmConfProfileName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object is used by the line alarm configuration table in order to identify a row of this table. When `dynamic' profiles are implemented, the profile name is user specified. Also, the system will always provide a default profile whose name is `DEFVAL'. When `static' profiles are implemented, there is an one-to-one relationship between each line and its profile. In which case, the profile name will need to algorithmicly represent the Line's ifIndex. Therefore, the profile's name is a decimalized string of the ifIndex that is fixed-length (i.e., 10) with leading zero(s). For example, the profile name for ifIndex which equals '15' will be '0000000015'." ::= { adslLineAlarmConfProfileEntry 1} Bathrick & Ly Standards Track [Page 79] RFC 2662 ADSL Line MIB August 1999 adslAtucThresh15MinLofs OBJECT-TYPE SYNTAX INTEGER(0..900) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The number of Loss of Frame Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfLofsThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 2} adslAtucThresh15MinLoss OBJECT-TYPE SYNTAX INTEGER(0..900) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The number of Loss of Signal Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfLossThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 3} adslAtucThresh15MinLols OBJECT-TYPE SYNTAX INTEGER(0..900) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The number of Loss of Link Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfLolsThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 4} adslAtucThresh15MinLprs OBJECT-TYPE SYNTAX INTEGER(0..900) UNITS "seconds" Bathrick & Ly Standards Track [Page 80] RFC 2662 ADSL Line MIB August 1999 MAX-ACCESS read-create STATUS current DESCRIPTION "The number of Loss of Power Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfLprsThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 5} adslAtucThresh15MinESs OBJECT-TYPE SYNTAX INTEGER(0..900) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The number of Errored Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfESsThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 6} adslAtucThreshFastRateUp OBJECT-TYPE SYNTAX Unsigned32 UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "Applies to `Fast' channels only. Configured change in rate causing an adslAtucRateChangeTrap. A trap is produced when: ChanCurrTxRate >= ChanPrevTxRate plus the value of this object. A value of `0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 7} adslAtucThreshInterleaveRateUp OBJECT-TYPE SYNTAX Unsigned32 UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "Applies to `Interleave' channels only. Configured change in rate causing an Bathrick & Ly Standards Track [Page 81] RFC 2662 ADSL Line MIB August 1999 adslAtucRateChangeTrap. A trap is produced when: ChanCurrTxRate >= ChanPrevTxRate plus the value of this object. A value of `0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 8} adslAtucThreshFastRateDown OBJECT-TYPE SYNTAX Unsigned32 UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "Applies to `Fast' channels only. Configured change in rate causing an adslAtucRateChangeTrap. A trap is produced when: ChanCurrTxRate <= ChanPrevTxRate minus the value of this object. A value of `0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 9 } adslAtucThreshInterleaveRateDown OBJECT-TYPE SYNTAX Unsigned32 UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "Applies to `Interleave' channels only. Configured change in rate causing an adslAtucRateChangeTrap. A trap is produced when: ChanCurrTxRate <= ChanPrevTxRate minus the value of this object. A value of `0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 10 } adslAtucInitFailureTrapEnable OBJECT-TYPE SYNTAX INTEGER { enable (1), disable (2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enables and disables the InitFailureTrap. This object is defaulted disable(2)." DEFVAL { disable } ::= { adslLineAlarmConfProfileEntry 11 } adslAturThresh15MinLofs OBJECT-TYPE SYNTAX INTEGER(0..900) UNITS "seconds" MAX-ACCESS read-create Bathrick & Ly Standards Track [Page 82] RFC 2662 ADSL Line MIB August 1999 STATUS current DESCRIPTION "The number of Loss of Frame Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAturPerfLofsThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 12 } adslAturThresh15MinLoss OBJECT-TYPE SYNTAX INTEGER(0..900) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The number of Loss of Signal Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAturPerfLossThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 13 } adslAturThresh15MinLprs OBJECT-TYPE SYNTAX INTEGER(0..900) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The number of Loss of Power Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAturPerfLprsThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 14 } adslAturThresh15MinESs OBJECT-TYPE SYNTAX INTEGER(0..900) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The number of Errored Seconds Bathrick & Ly Standards Track [Page 83] RFC 2662 ADSL Line MIB August 1999 encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAturPerfESsThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 15 } adslAturThreshFastRateUp OBJECT-TYPE SYNTAX Unsigned32 UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "Applies to `Fast' channels only. Configured change in rate causing an adslAturRateChangeTrap. A trap is produced when: ChanCurrTxRate >= ChanPrevTxRate plus the value of this object. A value of `0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 16 } adslAturThreshInterleaveRateUp OBJECT-TYPE SYNTAX Unsigned32 UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "Applies to `Interleave' channels only. configured change in rate causing an adslAturRateChangeTrap. A trap is produced when: ChanCurrTxRate >= ChanPrevTxRate plus the value of this object. A value of `0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 17 } adslAturThreshFastRateDown OBJECT-TYPE SYNTAX Unsigned32 UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "Applies to `Fast' channels only. Configured change in rate causing an adslAturRateChangeTrap. A trap is produced when: ChanCurrTxRate <= ChanPrevTxRate minus the value of this object. A value of `0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 18 } adslAturThreshInterleaveRateDown OBJECT-TYPE Bathrick & Ly Standards Track [Page 84] RFC 2662 ADSL Line MIB August 1999 SYNTAX Unsigned32 UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "Applies to `Interleave' channels only. Configured change in rate causing an adslAturRateChangeTrap. A trap is produced when: ChanCurrTxRate <= ChanPrevTxRate minus the value of this object. A value of `0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 19 } adslLineAlarmConfProfileRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or modify or delete an existing row in this table. A profile activated by setting this object to `active'. When `active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service, (by setting this object to `destroy' or `outOfService') it must be first unreferenced from all associated lines. If the implementator of this MIB has chosen not to implement `dynamic assignment' of profiles, this object's MIN-ACCESS is read-only and its value is always to be `active'." ::= { adslLineAlarmConfProfileEntry 20 } -- Line Code Specific Tables -- These are place holders for the Line Code Specific MIBs -- once they become available. adslLCSMib OBJECT IDENTIFIER ::= { adslMibObjects 16 } -- trap definitions adslTraps OBJECT IDENTIFIER ::= { adslLineMib 2 } adslAtucTraps OBJECT IDENTIFIER ::= { adslTraps 1 } Bathrick & Ly Standards Track [Page 85] RFC 2662 ADSL Line MIB August 1999 adslAtucPerfLofsThreshTrap NOTIFICATION-TYPE OBJECTS { adslAtucPerfCurr15MinLofs, adslAtucThresh15MinLofs } STATUS current DESCRIPTION "Loss of Framing 15-minute interval threshold reached." ::= { adslAtucTraps 0 1 } adslAtucPerfLossThreshTrap NOTIFICATION-TYPE OBJECTS { adslAtucPerfCurr15MinLoss, adslAtucThresh15MinLoss } STATUS current DESCRIPTION "Loss of Signal 15-minute interval threshold reached." ::= { adslAtucTraps 0 2 } adslAtucPerfLprsThreshTrap NOTIFICATION-TYPE OBJECTS { adslAtucPerfCurr15MinLprs, adslAtucThresh15MinLprs } STATUS current DESCRIPTION "Loss of Power 15-minute interval threshold reached." ::= { adslAtucTraps 0 3 } adslAtucPerfESsThreshTrap NOTIFICATION-TYPE OBJECTS { adslAtucPerfCurr15MinESs, adslAtucThresh15MinESs } STATUS current DESCRIPTION "Errored Second 15-minute interval threshold reached." ::= { adslAtucTraps 0 4 } adslAtucRateChangeTrap NOTIFICATION-TYPE OBJECTS { adslAtucChanCurrTxRate, adslAtucChanPrevTxRate } STATUS current DESCRIPTION "The ATUCs transmit rate has changed (RADSL mode only)" ::= { adslAtucTraps 0 5 } adslAtucPerfLolsThreshTrap NOTIFICATION-TYPE OBJECTS { adslAtucPerfCurr15MinLols, adslAtucThresh15MinLols } STATUS current DESCRIPTION "Loss of Link 15-minute interval threshold reached." ::= { adslAtucTraps 0 6 } Bathrick & Ly Standards Track [Page 86] RFC 2662 ADSL Line MIB August 1999 adslAtucInitFailureTrap NOTIFICATION-TYPE OBJECTS { adslAtucCurrStatus } STATUS current DESCRIPTION "ATUC initialization failed. See adslAtucCurrStatus for potential reasons." ::= { adslAtucTraps 0 7 } adslAturTraps OBJECT IDENTIFIER ::= { adslTraps 2 } adslAturPerfLofsThreshTrap NOTIFICATION-TYPE OBJECTS { adslAturPerfCurr15MinLofs, adslAturThresh15MinLofs } STATUS current DESCRIPTION "Loss of Framing 15-minute interval threshold reached." ::= { adslAturTraps 0 1 } adslAturPerfLossThreshTrap NOTIFICATION-TYPE OBJECTS { adslAturPerfCurr15MinLoss, adslAturThresh15MinLoss } STATUS current DESCRIPTION "Loss of Signal 15-minute interval threshold reached." ::= { adslAturTraps 0 2 } adslAturPerfLprsThreshTrap NOTIFICATION-TYPE OBJECTS { adslAturPerfCurr15MinLprs, adslAturThresh15MinLprs } STATUS current DESCRIPTION "Loss of Power 15-minute interval threshold reached." ::= { adslAturTraps 0 3 } adslAturPerfESsThreshTrap NOTIFICATION-TYPE OBJECTS { adslAturPerfCurr15MinESs, adslAturThresh15MinESs } STATUS current DESCRIPTION "Errored Second 15-minute interval threshold reached." ::= { adslAturTraps 0 4 } adslAturRateChangeTrap NOTIFICATION-TYPE OBJECTS { adslAturChanCurrTxRate, adslAturChanPrevTxRate } STATUS current DESCRIPTION "The ATURs transmit rate has changed (RADSL mode only)" Bathrick & Ly Standards Track [Page 87] RFC 2662 ADSL Line MIB August 1999 ::= { adslAturTraps 0 5 } -- no adslAturPerfLolsThreshTrap possible { 0 6 } -- no adslAturInitFailureTrap possible { 0 7 } -- conformance information adslConformance OBJECT IDENTIFIER ::= { adslLineMib 3 } adslGroups OBJECT IDENTIFIER ::= { adslConformance 1 } adslCompliances OBJECT IDENTIFIER ::= { adslConformance 2 } -- ATU-C agent compliance statements adslLineMibAtucCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for SNMP entities which manage ADSL ATU-C interfaces." MODULE -- this module MANDATORY-GROUPS { adslLineGroup, adslPhysicalGroup, adslChannelGroup, adslAtucPhysPerfIntervalGroup, adslAturPhysPerfIntervalGroup, adslLineConfProfileGroup, adslLineAlarmConfProfileGroup, adslLineConfProfileControlGroup } GROUP adslAtucPhysPerfRawCounterGroup DESCRIPTION "This group is optional. Implementations which require continuous ATU-C physical event counters should implement this group." GROUP adslAturPhysPerfRawCounterGroup DESCRIPTION "This group is optional. Implementations which require continuous ATU-R physical event counters should implement this group." GROUP adslAtucChanPerformanceGroup DESCRIPTION "This group is optional. Implementations which require ATU-C channel block event counters should implement this group." Bathrick & Ly Standards Track [Page 88] RFC 2662 ADSL Line MIB August 1999 GROUP adslAturChanPerformanceGroup DESCRIPTION "This group is optional. Implementations which require ATU-R channel block event counters should implement this group." OBJECT adslLineConfProfile MIN-ACCESS read-only DESCRIPTION "Read-only access is applicable when static profiles are implemented." OBJECT adslAtucConfRateMode MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucConfRateChanRatio MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucConfTargetSnrMgn MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucConfMaxSnrMgn MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucConfMinSnrMgn MIN-ACCESS read-wr MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucConfDownshiftSnrMgn MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." Bathrick & Ly Standards Track [Page 89] RFC 2662 ADSL Line MIB August 1999 OBJECT adslAtucConfUpshiftSnrMgn MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucConfMinUpshiftTime MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucConfMinDownshiftTime MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucChanConfFastMinTxRate MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucChanConfInterleaveMinTxRate MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucChanConfFastMaxTxRate MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucChanConfInterleaveMaxTxRate MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucChanConfMaxInterleaveDelay MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." Bathrick & Ly Standards Track [Page 90] RFC 2662 ADSL Line MIB August 1999 OBJECT adslAturConfRateMode MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturConfRateChanRatio MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturConfTargetSnrMgn MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturConfMaxSnrMgn MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturConfMinSnrMgn MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturConfDownshiftSnrMgn MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturConfUpshiftSnrMgn MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturConfMinUpshiftTime MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." Bathrick & Ly Standards Track [Page 91] RFC 2662 ADSL Line MIB August 1999 OBJECT adslAturConfMinDownshiftTime MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturChanConfFastMinTxRate MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturChanConfInterleaveMinTxRate MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturChanConfFastMaxTxRate MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturChanConfInterleaveMaxTxRate MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturChanConfMaxInterleaveDelay MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslLineConfProfileRowStatus MIN-ACCESS read-only DESCRIPTION "Read-only access is applicable only when static profiles are implemented." OBJECT adslLineAlarmConfProfile MIN-ACCESS read-only DESCRIPTION "Read-only access is applicable only when static profiles are implemented." Bathrick & Ly Standards Track [Page 92] RFC 2662 ADSL Line MIB August 1999 OBJECT adslAtucThresh15MinLofs MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucThresh15MinLoss MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucThresh15MinLols MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucThresh15MinLprs MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucThresh15MinESs MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucThreshFastRateUp MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucThreshInterleaveRateUp MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucThreshFastRateDown MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." Bathrick & Ly Standards Track [Page 93] RFC 2662 ADSL Line MIB August 1999 OBJECT adslAtucThreshInterleaveRateDown MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucInitFailureTrapEnable MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturThresh15MinLofs MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturThresh15MinLoss MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturThresh15MinLprs MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturThresh15MinESs MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturThreshFastRateUp MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturThreshInterleaveRateUp MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." Bathrick & Ly Standards Track [Page 94] RFC 2662 ADSL Line MIB August 1999 OBJECT adslAturThreshFastRateDown MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturThreshInterleaveRateDown MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslLineAlarmConfProfileRowStatus MIN-ACCESS read-only DESCRIPTION "Read-only access is applicable only when static profiles are implemented." ::= { adslCompliances 1 } -- ATU-R agent compliance statements adslLineMibAturCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for SNMP entities which manage ADSL ATU-R interfaces." MODULE -- this module MANDATORY-GROUPS { adslAturLineGroup, adslAturPhysicalGroup, adslAturChannelGroup, adslAturAtucPhysPerfIntervalGroup, adslAturAturPhysPerfIntervalGroup, adslAturLineAlarmConfProfileGroup, adslAturLineConfProfileControlGroup } GROUP adslAturAtucPhysPerfRawCounterGroup DESCRIPTION "This group is optional. Implementations which require continuous ATU-C physical event counters should implement this group." GROUP adslAturAturPhysPerfRawCounterGroup DESCRIPTION "This group is optional. Implementations which Bathrick & Ly Standards Track [Page 95] RFC 2662 ADSL Line MIB August 1999 require continuous ATU-R physical event counters should implement this group." GROUP adslAturAtucChanPerformanceGroup DESCRIPTION "This group is optional. Implementations which require ATU-C channel block event counters should implement this group." GROUP adslAturAturChanPerformanceGroup DESCRIPTION "This group is optional. Implementations which require ATU-R channel block event counters should implement this group." OBJECT adslLineAlarmConfProfile MIN-ACCESS read-only DESCRIPTION "Read-only access is applicable only when static profiles are implemented." OBJECT adslAtucThresh15MinLofs MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucThresh15MinLoss MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucThresh15MinESs MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucThreshFastRateUp MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucThreshInterleaveRateUp MIN-ACCESS read-write DESCRIPTION Bathrick & Ly Standards Track [Page 96] RFC 2662 ADSL Line MIB August 1999 "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucThreshFastRateDown MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucInitFailureTrapEnable MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturThresh15MinLofs MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturThresh15MinLoss MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturThresh15MinLprs MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturThresh15MinESs MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturThreshFastRateUp MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturThreshInterleaveRateUp MIN-ACCESS read-write Bathrick & Ly Standards Track [Page 97] RFC 2662 ADSL Line MIB August 1999 DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturThreshFastRateDown MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAturThreshInterleaveRateDown MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslLineAlarmConfProfileRowStatus MIN-ACCESS read-only DESCRIPTION "Read-only access is applicable only when static profiles are implemented." OBJECT adslAtucCurrStatus SYNTAX BITS { noDefect(0), lossOfFraming(1), lossOfSignal(2) } DESCRIPTION "It is allowable to implement only noDefect(0), lossOfFraming(1) and lossOfSignal(2) by the ATU-R agent." ::= { adslCompliances 2 } -- units of conformance adslLineGroup OBJECT-GROUP OBJECTS { adslLineCoding, adslLineType, adslLineSpecific } STATUS current DESCRIPTION "A collection of objects providing configuration information about an ADSL Line." ::= { adslGroups 1 } adslPhysicalGroup OBJECT-GROUP OBJECTS { Bathrick & Ly Standards Track [Page 98] RFC 2662 ADSL Line MIB August 1999 adslAtucInvSerialNumber, adslAtucInvVendorID, adslAtucInvVersionNumber, adslAtucCurrSnrMgn, adslAtucCurrAtn, adslAtucCurrStatus, adslAtucCurrOutputPwr, adslAtucCurrAttainableRate, adslAturInvSerialNumber, adslAturInvVendorID, adslAturInvVersionNumber, adslAturCurrSnrMgn, adslAturCurrAtn, adslAturCurrStatus, adslAturCurrOutputPwr, adslAturCurrAttainableRate } STATUS current DESCRIPTION "A collection of objects providing physical configuration information of the ADSL Line." ::= { adslGroups 2 } adslChannelGroup OBJECT-GROUP OBJECTS { adslAtucChanInterleaveDelay, adslAtucChanCurrTxRate, adslAtucChanPrevTxRate, adslAtucChanCrcBlockLength, adslAturChanInterleaveDelay, adslAturChanCurrTxRate, adslAturChanPrevTxRate, adslAturChanCrcBlockLength } STATUS current DESCRIPTION "A collection of objects providing configuration information about an ADSL channel." ::= { adslGroups 3 } adslAtucPhysPerfRawCounterGroup OBJECT-GROUP OBJECTS { adslAtucPerfLofs, adslAtucPerfLoss, adslAtucPerfLols, adslAtucPerfLprs, adslAtucPerfESs, adslAtucPerfInits } STATUS current DESCRIPTION "A collection of objects providing raw performance counts on an ADSL Line (ATU-C end)." ::= { adslGroups 4 } adslAtucPhysPerfIntervalGroup OBJECT-GROUP OBJECTS { adslAtucPerfValidIntervals, adslAtucPerfInvalidIntervals, adslAtucPerfCurr15MinTimeElapsed, adslAtucPerfCurr15MinLofs, adslAtucPerfCurr15MinLoss, adslAtucPerfCurr15MinLols, adslAtucPerfCurr15MinLprs, adslAtucPerfCurr15MinESs, adslAtucPerfCurr15MinInits, Bathrick & Ly Standards Track [Page 99] RFC 2662 ADSL Line MIB August 1999 adslAtucPerfCurr1DayLofs, adslAtucPerfCurr1DayLoss, adslAtucPerfCurr1DayLols, adslAtucPerfCurr1DayLprs, adslAtucPerfCurr1DayESs, adslAtucPerfCurr1DayInits, adslAtucPerfPrev1DayMoniSecs, adslAtucPerfPrev1DayLofs, adslAtucPerfPrev1DayLoss, adslAtucPerfPrev1DayLols, adslAtucPerfPrev1DayLprs, adslAtucPerfPrev1DayESs, adslAtucPerfPrev1DayInits, adslAtucIntervalLofs, adslAtucIntervalLoss, adslAtucIntervalLols, adslAtucIntervalLprs, adslAtucIntervalESs, adslAtucIntervalInits, adslAtucIntervalValidData } STATUS current DESCRIPTION "A collection of objects providing current 15-minute, 1-day; and previous 1-day performance counts on ADSL Line (ATU-C end) ." ::= { adslGroups 5 } adslAturPhysPerfRawCounterGroup OBJECT-GROUP OBJECTS { adslAturPerfLofs, adslAturPerfLoss, adslAturPerfLprs, adslAturPerfESs } STATUS current DESCRIPTION "A collection of objects providing raw performance counts on an ADSL Line (ATU-R end)." ::= { adslGroups 6 } adslAturPhysPerfIntervalGroup OBJECT-GROUP OBJECTS { adslAturPerfValidIntervals, adslAturPerfInvalidIntervals, adslAturPerfCurr15MinTimeElapsed, adslAturPerfCurr15MinLofs, adslAturPerfCurr15MinLoss, adslAturPerfCurr15MinLprs, adslAturPerfCurr15MinESs, adslAturPerfCurr1DayTimeElapsed, adslAturPerfCurr1DayLofs, adslAturPerfCurr1DayLoss, adslAturPerfCurr1DayLprs, adslAturPerfCurr1DayESs, adslAturPerfPrev1DayMoniSecs, adslAturPerfPrev1DayLofs, adslAturPerfPrev1DayLoss, adslAturPerfPrev1DayLprs, adslAturPerfPrev1DayESs, adslAturIntervalLofs, adslAturIntervalLoss, adslAturIntervalLprs, adslAturIntervalESs, adslAturIntervalValidData } Bathrick & Ly Standards Track [Page 100] RFC 2662 ADSL Line MIB August 1999 STATUS current DESCRIPTION "A collection of objects providing current 15-minute, 1-day; and previous 1-day performance counts on ADSL Line (ATU-R end)." ::= { adslGroups 7 } adslAtucChanPerformanceGroup OBJECT-GROUP OBJECTS { adslAtucChanReceivedBlks, adslAtucChanTransmittedBlks, adslAtucChanCorrectedBlks, adslAtucChanUncorrectBlks, adslAtucChanPerfValidIntervals, adslAtucChanPerfInvalidIntervals, adslAtucChanPerfCurr15MinTimeElapsed, adslAtucChanPerfCurr15MinReceivedBlks, adslAtucChanPerfCurr15MinTransmittedBlks, adslAtucChanPerfCurr15MinCorrectedBlks, adslAtucChanPerfCurr15MinUncorrectBlks, adslAtucChanPerfCurr1DayTimeElapsed, adslAtucChanPerfCurr1DayReceivedBlks, adslAtucChanPerfCurr1DayTransmittedBlks, adslAtucChanPerfCurr1DayCorrectedBlks, adslAtucChanPerfCurr1DayUncorrectBlks, adslAtucChanPerfPrev1DayMoniSecs, adslAtucChanPerfPrev1DayReceivedBlks, adslAtucChanPerfPrev1DayTransmittedBlks, adslAtucChanPerfPrev1DayCorrectedBlks, adslAtucChanPerfPrev1DayUncorrectBlks, adslAtucChanIntervalReceivedBlks, adslAtucChanIntervalTransmittedBlks, adslAtucChanIntervalCorrectedBlks, adslAtucChanIntervalUncorrectBlks, adslAtucChanIntervalValidData } STATUS current DESCRIPTION "A collection of objects providing channel block performance information on an ADSL channel (ATU-C end)." ::= { adslGroups 8 } adslAturChanPerformanceGroup OBJECT-GROUP OBJECTS { adslAturChanReceivedBlks, adslAturChanTransmittedBlks, adslAturChanCorrectedBlks, Bathrick & Ly Standards Track [Page 101] RFC 2662 ADSL Line MIB August 1999 adslAturChanUncorrectBlks, adslAturChanPerfValidIntervals, adslAturChanPerfInvalidIntervals, adslAturChanPerfCurr15MinTimeElapsed, adslAturChanPerfCurr15MinReceivedBlks, adslAturChanPerfCurr15MinTransmittedBlks, adslAturChanPerfCurr15MinCorrectedBlks, adslAturChanPerfCurr15MinUncorrectBlks, adslAturChanPerfCurr1DayTimeElapsed, adslAturChanPerfCurr1DayReceivedBlks, adslAturChanPerfCurr1DayTransmittedBlks, adslAturChanPerfCurr1DayCorrectedBlks, adslAturChanPerfCurr1DayUncorrectBlks, adslAturChanPerfPrev1DayMoniSecs, adslAturChanPerfPrev1DayReceivedBlks, adslAturChanPerfPrev1DayTransmittedBlks, adslAturChanPerfPrev1DayCorrectedBlks, adslAturChanPerfPrev1DayUncorrectBlks, adslAturChanIntervalReceivedBlks, adslAturChanIntervalTransmittedBlks, adslAturChanIntervalCorrectedBlks, adslAturChanIntervalUncorrectBlks, adslAturChanIntervalValidData } STATUS current DESCRIPTION "A collection of objects providing channel block performance information on an ADSL channel (ATU-C end)." ::= { adslGroups 9 } adslLineConfProfileGroup OBJECT-GROUP OBJECTS { adslAtucConfRateMode, adslAtucConfRateChanRatio, adslAtucConfTargetSnrMgn, adslAtucConfMaxSnrMgn, adslAtucConfMinSnrMgn, adslAtucConfDownshiftSnrMgn, adslAtucConfUpshiftSnrMgn, adslAtucConfMinUpshiftTime, adslAtucConfMinDownshiftTime, adslAtucChanConfFastMinTxRate, adslAtucChanConfInterleaveMinTxRate, adslAtucChanConfFastMaxTxRate, adslAtucChanConfInterleaveMaxTxRate, adslAtucChanConfMaxInterleaveDelay, adslAturConfRateMode, adslAturConfRateChanRatio, adslAturConfTargetSnrMgn, adslAturConfMaxSnrMgn, adslAturConfMinSnrMgn, adslAturConfDownshiftSnrMgn, Bathrick & Ly Standards Track [Page 102] RFC 2662 ADSL Line MIB August 1999 adslAturConfUpshiftSnrMgn, adslAturConfMinUpshiftTime, adslAturConfMinDownshiftTime, adslAturChanConfFastMinTxRate, adslAturChanConfInterleaveMinTxRate, adslAturChanConfFastMaxTxRate, adslAturChanConfInterleaveMaxTxRate, adslAturChanConfMaxInterleaveDelay } STATUS current DESCRIPTION "A collection of objects providing provisioning information about an ADSL Line." ::= { adslGroups 10 } adslLineAlarmConfProfileGroup OBJECT-GROUP OBJECTS { adslAtucThresh15MinLofs, adslAtucThresh15MinLoss, adslAtucThresh15MinLols, adslAtucThresh15MinLprs, adslAtucThresh15MinESs, adslAtucThreshFastRateUp, adslAtucThreshInterleaveRateUp, adslAtucThreshFastRateDown, adslAtucThreshInterleaveRateDown, adslAtucInitFailureTrapEnable, adslAturThresh15MinLofs, adslAturThresh15MinLoss, adslAturThresh15MinLprs, adslAturThresh15MinESs, adslAturThreshFastRateUp, adslAturThreshInterleaveRateUp, adslAturThreshFastRateDown, adslAturThreshInterleaveRateDown } STATUS current DESCRIPTION "A collection of objects providing alarm provisioning information about an ADSL Line." ::= { adslGroups 11 } adslLineConfProfileControlGroup OBJECT-GROUP OBJECTS { adslLineConfProfile, adslLineAlarmConfProfile, adslLineConfProfileRowStatus, adslLineAlarmConfProfileRowStatus } STATUS current DESCRIPTION "A collection of objects providing profile control for the ADSL system." ::= { adslGroups 12 } Bathrick & Ly Standards Track [Page 103] RFC 2662 ADSL Line MIB August 1999 adslNotificationsGroup NOTIFICATION-GROUP NOTIFICATIONS { adslAtucPerfLofsThreshTrap, adslAtucPerfLossThreshTrap, adslAtucPerfLprsThreshTrap, adslAtucPerfESsThreshTrap, adslAtucRateChangeTrap, adslAtucPerfLolsThreshTrap, adslAtucInitFailureTrap, adslAturPerfLofsThreshTrap, adslAturPerfLossThreshTrap, adslAturPerfLprsThreshTrap, adslAturPerfESsThreshTrap, adslAturRateChangeTrap } STATUS current DESCRIPTION "The collection of adsl notifications." ::= { adslGroups 13 } -- units of conformance for ATU-R agent adslAturLineGroup OBJECT-GROUP OBJECTS { adslLineCoding } STATUS current DESCRIPTION "A collection of objects providing configuration information about an ADSL Line on the ATU-R side." ::= { adslGroups 14 } adslAturPhysicalGroup OBJECT-GROUP OBJECTS { adslAtucInvVendorID, adslAtucInvVersionNumber, adslAtucCurrOutputPwr, adslAtucCurrAttainableRate, adslAturInvSerialNumber, adslAturInvVendorID, adslAturInvVersionNumber, adslAturCurrSnrMgn, adslAturCurrAtn, adslAturCurrStatus, adslAturCurrOutputPwr, adslAturCurrAttainableRate, adslAtucCurrStatus } STATUS current DESCRIPTION "A collection of objects providing physical configuration information of the ADSL Line on the ATU-R side." Bathrick & Ly Standards Track [Page 104] RFC 2662 ADSL Line MIB August 1999 ::= { adslGroups 15 } adslAturChannelGroup OBJECT-GROUP OBJECTS { adslAtucChanInterleaveDelay, adslAtucChanCurrTxRate, adslAtucChanPrevTxRate, adslAturChanInterleaveDelay, adslAturChanCurrTxRate, adslAturChanPrevTxRate, adslAturChanCrcBlockLength } STATUS current DESCRIPTION "A collection of objects providing configuration information about an ADSL channel on the ATU-R side." ::= { adslGroups 16 } adslAturAtucPhysPerfRawCounterGroup OBJECT-GROUP OBJECTS { adslAtucPerfLofs, adslAtucPerfLoss, adslAtucPerfESs, adslAtucPerfInits } STATUS current DESCRIPTION "A collection of objects providing raw performance counts on an ADSL Line (ATU-C end) provided by the ATU-R agent." ::= { adslGroups 17 } adslAturAtucPhysPerfIntervalGroup OBJECT-GROUP OBJECTS { adslAtucPerfValidIntervals, adslAtucPerfInvalidIntervals, adslAtucPerfCurr15MinTimeElapsed, adslAtucPerfCurr15MinLofs, adslAtucPerfCurr15MinLoss, adslAtucPerfCurr15MinESs, adslAtucPerfCurr15MinInits, adslAtucPerfCurr1DayTimeElapsed, adslAtucPerfCurr1DayLofs, adslAtucPerfCurr1DayLoss, adslAtucPerfCurr1DayESs, adslAtucPerfCurr1DayInits, adslAtucPerfPrev1DayMoniSecs, adslAtucPerfPrev1DayLofs, adslAtucPerfPrev1DayLoss, adslAtucPerfPrev1DayESs, adslAtucPerfPrev1DayInits, adslAtucIntervalLofs, adslAtucIntervalLoss, adslAtucIntervalESs, adslAtucIntervalInits, adslAtucIntervalValidData } STATUS current DESCRIPTION "A collection of objects providing current Bathrick & Ly Standards Track [Page 105] RFC 2662 ADSL Line MIB August 1999 15-minute, 1-day; and previous 1-day performance counts on ADSL Line (ATU-C end) provided by the ATU-R agent." ::= { adslGroups 18 } adslAturAturPhysPerfRawCounterGroup OBJECT-GROUP OBJECTS { adslAturPerfLofs, adslAturPerfLoss, adslAturPerfLprs, adslAturPerfESs } STATUS current DESCRIPTION "A collection of objects providing raw performance counts on an ADSL Line (ATU-R end) provided by the ATU-R agent." ::= { adslGroups 19 } adslAturAturPhysPerfIntervalGroup OBJECT-GROUP OBJECTS { adslAturPerfValidIntervals, adslAturPerfInvalidIntervals, adslAturPerfCurr15MinTimeElapsed, adslAturPerfCurr15MinLofs, adslAturPerfCurr15MinLoss, adslAturPerfCurr15MinLprs, adslAturPerfCurr15MinESs, adslAturPerfCurr1DayTimeElapsed, adslAturPerfCurr1DayLofs, adslAturPerfCurr1DayLoss, adslAturPerfCurr1DayLprs, adslAturPerfCurr1DayESs, adslAturPerfPrev1DayMoniSecs, adslAturPerfPrev1DayLofs, adslAturPerfPrev1DayLoss, adslAturPerfPrev1DayLprs, adslAturPerfPrev1DayESs, adslAturIntervalLofs, adslAturIntervalLoss, adslAturIntervalLprs, adslAturIntervalESs, adslAturIntervalValidData } STATUS current DESCRIPTION "A collection of objects providing current 15-minute, 1-day; and previous 1-day performance counts on ADSL Line (ATU-R end) provided by the ATU-R agent." ::= { adslGroups 20 } adslAturAtucChanPerformanceGroup OBJECT-GROUP OBJECTS { adslAtucChanReceivedBlks, adslAtucChanTransmittedBlks, adslAtucChanCorrectedBlks, adslAtucChanUncorrectBlks, Bathrick & Ly Standards Track [Page 106] RFC 2662 ADSL Line MIB August 1999 adslAtucChanPerfCurr15MinTimeElapsed, adslAtucChanPerfCurr15MinReceivedBlks, adslAtucChanPerfCurr15MinTransmittedBlks, adslAtucChanPerfCurr15MinCorrectedBlks, adslAtucChanPerfCurr15MinUncorrectBlks, adslAtucChanPerfCurr1DayTimeElapsed, adslAtucChanPerfCurr1DayReceivedBlks, adslAtucChanPerfCurr1DayTransmittedBlks, adslAtucChanPerfCurr1DayCorrectedBlks, adslAtucChanPerfCurr1DayUncorrectBlks, adslAtucChanPerfPrev1DayMoniSecs, adslAtucChanPerfPrev1DayReceivedBlks, adslAtucChanPerfPrev1DayTransmittedBlks, adslAtucChanPerfPrev1DayCorrectedBlks, adslAtucChanPerfPrev1DayUncorrectBlks, adslAtucChanPerfValidIntervals, adslAtucChanPerfInvalidIntervals, adslAtucChanIntervalReceivedBlks, adslAtucChanIntervalTransmittedBlks, adslAtucChanIntervalCorrectedBlks, adslAtucChanIntervalUncorrectBlks, adslAtucChanIntervalValidData } STATUS current DESCRIPTION "A collection of objects providing channel block performance information on an ADSL channel (ATU-C end) provided by the ATU-R agent." ::= { adslGroups 21 } adslAturAturChanPerformanceGroup OBJECT-GROUP OBJECTS { adslAturChanReceivedBlks, adslAturChanTransmittedBlks, adslAturChanCorrectedBlks, adslAturChanUncorrectBlks, adslAturChanPerfValidIntervals, adslAturChanPerfInvalidIntervals, adslAturChanPerfCurr15MinTimeElapsed, adslAturChanPerfCurr15MinReceivedBlks, adslAturChanPerfCurr15MinTransmittedBlks, adslAturChanPerfCurr15MinCorrectedBlks, adslAturChanPerfCurr15MinUncorrectBlks, adslAturChanPerfCurr1DayTimeElapsed, adslAturChanPerfCurr1DayReceivedBlks, adslAturChanPerfCurr1DayTransmittedBlks, adslAturChanPerfCurr1DayCorrectedBlks, adslAturChanPerfCurr1DayUncorrectBlks, Bathrick & Ly Standards Track [Page 107] RFC 2662 ADSL Line MIB August 1999 adslAturChanPerfPrev1DayMoniSecs, adslAturChanPerfPrev1DayReceivedBlks, adslAturChanPerfPrev1DayTransmittedBlks, adslAturChanPerfPrev1DayCorrectedBlks, adslAturChanPerfPrev1DayUncorrectBlks, adslAturChanIntervalReceivedBlks, adslAturChanIntervalTransmittedBlks, adslAturChanIntervalCorrectedBlks, adslAturChanIntervalUncorrectBlks, adslAturChanIntervalValidData } STATUS current DESCRIPTION "A collection of objects providing channel block performance information on an ADSL channel (ATU-R end) provided by the ATU-R agent." ::= { adslGroups 22 } adslAturLineAlarmConfProfileGroup OBJECT-GROUP OBJECTS { adslAtucThresh15MinLofs, adslAtucThresh15MinLoss, adslAtucThresh15MinESs, adslAtucThreshFastRateUp, adslAtucThreshInterleaveRateUp, adslAtucThreshFastRateDown, adslAtucThreshInterleaveRateDown, adslAtucInitFailureTrapEnable, adslAturThresh15MinLofs, adslAturThresh15MinLoss, adslAturThresh15MinLprs, adslAturThresh15MinESs, adslAturThreshFastRateUp, adslAturThreshInterleaveRateUp, adslAturThreshFastRateDown, adslAturThreshInterleaveRateDown } STATUS current DESCRIPTION "A collection of objects providing alarm provisioning information about an ADSL Line provided by the ATU-R agent." ::= { adslGroups 23 } adslAturLineConfProfileControlGroup OBJECT-GROUP OBJECTS { adslLineAlarmConfProfile, adslLineAlarmConfProfileRowStatus } STATUS current DESCRIPTION Bathrick & Ly Standards Track [Page 108] RFC 2662 ADSL Line MIB August 1999 "A collection of objects providing profile control for the ADSL system by the ATU-R agent." ::= { adslGroups 24 } adslAturNotificationsGroup NOTIFICATION-GROUP NOTIFICATIONS { adslAtucPerfLofsThreshTrap, adslAtucPerfLossThreshTrap, adslAtucPerfESsThreshTrap, adslAtucRateChangeTrap, adslAturPerfLofsThreshTrap, adslAturPerfLossThreshTrap, adslAturPerfLprsThreshTrap, adslAturPerfESsThreshTrap, adslAturRateChangeTrap } STATUS current DESCRIPTION "The collection of ADSL notifications implemented by the ATU-R agent." ::= { adslGroups 25 } END Bathrick & Ly Standards Track [Page 109] RFC 2662 ADSL Line MIB August 1999 8. Acknowledgments The current authors/editors are: Gregory Bathrick (AG Communication Systems) Faye Ly (Copper Mountain Networks) Input from the ADSL Forum was edited by: Gregory Bathrick (AG Communication Systems) John Burgess (Predictive Systems) Contributions have been received from, but not limited to the following. (in alphabetical order) David Allen (Nortel) Rajesh Abbi (Alcatel) Gregory Bathrick (AG Communication Systems) Umberto Bonollo (NEC) John Burgess (Predictive Systems) Gail Cone (Amati) Andrew Cheers (NEC) Peter Duffy (Atlantech) Kevin Godfrey (Motorola) Bill Hong (Diamond Lane) Bob Jenness (Siemens) Lars Johansson (Ericsson) Jeff Johnson (RedBack Network) Tsu Kai Lu (DSC) Faye Ly (Copper Mountain Networks) Gigi Karmous-Edwards (Pulsecom) Ron Knipper (Diamond Lane) Adil Masood (AG Communication Systems) Padmore Peterson (BT) Anna Salguero (SBC) Donald Simon (Motorola) Mike Sneed (Pulsecom) Ted Soo-Hoo (Pulsecom) John Stehman (Diamond Lane) Chuck Storry (Newbridge) Chi-Lin Tom (AFC) Frank Van der Putten (Alcatel) Marc Van Vlimmeren (Alcatel) Bert Wijnen (IBM) Bathrick & Ly Standards Track [Page 110] RFC 2662 ADSL Line MIB August 1999 9. References [1] McCloghrie K., Perkins D. and J. Schoenwaelder, "Structure of Management Information Version 2 (SMIv2)", STD 58, RFC 2578, April 1999. [2] McCloghrie K., Perkins D. and J. Schoenwaelder, "Textual Conventions for SMIv2", STD 58, RFC 2579, April 1999. [3] ADSL Forum TR-005, "Network Management Element Management", March 1998. [4] McCloghrie, K. and M. Rose, Editors, "Management Information Base for Network Management of TCP/IP-based internets: MIB-II", STD 17, RFC 1213, March 1991. [5] McCloghrie, K. and F. Kastenholz, "The Interfaces Group MIB using SMIv2", RFC 2233, November 1997. [6] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser, "Management Information Base for version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1907, January 1996. [7] Case, J., Fedor, M., Schoffstall, M. and J. Davin. " A Simple Network Management Protocol (SNMP)", STD 15, RFC 1157, May 1990. [8] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser, "Protocol Operations for Version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1905, January 1996. [9] ADSL Forum TR-006, "SNMP-based ADSL Line MIB", March 1998. [10] American National Standards Institute, ANSI T1.413-1995, August 1995. [11] ADSL Forum WT-014, "DMT Line Code Specific MIB", February 1999. [12] ADSL Forum WT-015, "CAP Line Code Specific MIB", February 1999. [13] Wijnen, B., Harrington, D. and R. Presuhn, "An Architecture for Describing SNMP Management Frameworks", RFC 2571, April 1999. [14] Rose, M. and K. McCloghrie, "Structure and Identification of Management Information for TCP/IP-based Internets", STD 16, RFC 1155, May 1990. Bathrick & Ly Standards Track [Page 111] RFC 2662 ADSL Line MIB August 1999 [15] Rose, M. and K. McCloghrie, "Concise MIB Definitions", STD 16, RFC 1212, March 1991. [16] Rose, M., "A Convention for Defining Traps for use with the SNMP", RFC 1215, March 1991. [17] McCloghrie K., Perkins D. and J. Schoenwaelder, "Conformance Statements for SMIv2", RFC 2580, April 1999. [18] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser, "Introduction to Community-based SNMPv2", RFC 1901, January 1996. [19] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser, "Transport Mappings for Version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1906, January 1996. [20] Case, J., Harrington D., Presuhn R. and B. Wijnen, "Message Processing and Dispatching for the Simple Network Management Protocol (SNMP)", RFC 2572, April 1999. [21] Blumenthal, U. and B. Wijnen, "User-based Security Model (USM) for version 3 of the Simple Network Management Protocol (SNMPv3)", RFC 2574, April 1999. [22] Levi, D., Meyer, P. and B. Stewart, "SNMP Applications", RFC 2573, April 1999. [23] Wijnen, B., Presuhn, R. and K. McCloghrie, "View-based Access Control Model (VACM) for the Simple Network Management Protocol (SNMP)", RFC 2575, April 1999. [24] Ahmed, M. and K. Tesink, Editors, "Definitions of Managed Objects for ATM Management Version 8.0 using SMIv2", RFC 1695, August 1994. [25] McCloghrie, K. and A. Bierman, "Entity MIB", RFC 2037, October 1996. [26] Yergeau, F., "UTF-8, a transformation format of ISO 10646", RFC 2279, January 1998. Bathrick & Ly Standards Track [Page 112] RFC 2662 ADSL Line MIB August 1999 10. Security Considerations 1) Blocking unauthorized access to the ADSL MIB via the element management system is outside the scope of this document. It should be noted that access to the MIB permits the unauthorized entity to modify the profiles (sect 6.4) such that both subscriber service and network operations can be interfered with. Subscriber service can be altered by modifying any of a number of service characteristics such as rate partitioning and maximum transmission rates. Network operations can be impacted by modification of trap thresholds such as SNR margins. 2) There are a number of managed objects in this MIB that may be considered to contain sensitive information. In particular, the certain objects may be considered sensitive in many environments, since it would allow an intruder to obtain information about which vendor's equipment is in use on the network. Therefore, it may be important in some environments to control read access to these objects and possibly to even encrypt the values of these object when sending them over the network via SNMP. Not all versions of SNMP provide features for such a secure environment. SNMPv1 by itself is such an insecure environment. Even if the network itself is secure (for example by using IPSec), even then, there is no control as to who on the secure network is allowed to access and GET (read) the objects in this MIB. It is recommended that the implementors consider the security features as provided by the SNMPv3 framework. Specifically, the use of the User-based Security Model RFC 2574 [21] and the View-based Access Control Model RFC 2575 [23] is recommended. It is then a customer/user responsibility to ensure that the SNMP entity giving access to an instance of this MIB, is properly configured to give access to those objects only to those principals (users) that have legitimate rights to access them. 3) ADSL layer connectivity from the ATU-R will permit the subscriber to manipulate both the ADSL link directly and the AOC/EOC channels for their own loop. For example, unchecked or unfiltered fluctuations initiated by the subscriber could generate sufficient traps to potentially overwhelm either the management interface to the network or the element manager. Other attacks affecting the ATU-R portions of the MIB may also be possible. Bathrick & Ly Standards Track [Page 113] RFC 2662 ADSL Line MIB August 1999 11. Intellectual Property Notice The IETF takes no position regarding the validity or scope of any intellectual property or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; neither does it represent that it has made any effort to identify any such rights. Information on the IETF's procedures with respect to rights in standards-track and standards-related documentation can be found in BCP-11. Copies of claims of rights made available for publication and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementers or users of this specification can be obtained from the IETF Secretariat." The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights which may cover technology that may be required to practice this standard. Please address the information to the IETF Executive Director. 12. Authors' Addresses Gregory Bathrick AG Communication Systems [A Subsidiary of Lucent Technologies] 2500 W Utopia Rd. Phoenix, AZ 85027 USA Phone: +1 602-582-7679 Fax: +1 602-582-7697 EMail: bathricg@agcs.com Faye Ly Copper Mountain Networks Norcal Office 2470 Embarcadero Way Palo Alto, CA 94303 Phone: +1 650-858-8500 Fax: +1 650-858-8085 EMail: faye@coppermountain.com Bathrick & Ly Standards Track [Page 114] RFC 2662 ADSL Line MIB August 1999 13. Full Copyright Statement Copyright (C) The Internet Society (1999). All Rights Reserved. This document and translations of it may be copied and furnished to others, and derivative works that comment on or otherwise explain it or assist in its implementation may be prepared, copied, published and distributed, in whole or in part, without restriction of any kind, provided that the above copyright notice and this paragraph are included on all such copies and derivative works. However, this document itself may not be modified in any way, such as by removing the copyright notice or references to the Internet Society or other Internet organizations, except as needed for the purpose of developing Internet standards in which case the procedures for copyrights defined in the Internet Standards process must be followed, or as required to translate it into languages other than English. The limited permissions granted above are perpetual and will not be revoked by the Internet Society or its successors or assigns. This document and the information contained herein is provided on an "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Acknowledgement Funding for the RFC Editor function is currently provided by the Internet Society. Bathrick & Ly Standards Track [Page 115]